Boot Debian from SATA (GoFlex Net) March 26, 2012 03:20PM |
Registered: 12 years ago Posts: 17 |
Re: Boot Debian from SATA (GoFlex Net) March 26, 2012 08:11PM |
Registered: 12 years ago Posts: 501 |
Re: Boot Debian from SATA (GoFlex Net) March 27, 2012 03:24PM |
Registered: 12 years ago Posts: 17 |
Yes.Quote
Did you actually clone the USB rootfs and other partitions to the SATA drive already?
Quote
Did you enable and set up netconsole already?
Too few good blocks within range
Re: Boot Debian from SATA (GoFlex Net) March 27, 2012 03:32PM |
Registered: 12 years ago Posts: 501 |
Re: Boot Debian from SATA (GoFlex Net) March 27, 2012 03:41PM |
Registered: 12 years ago Posts: 17 |
Re: Boot Debian from SATA (GoFlex Net) March 27, 2012 03:54PM |
Registered: 12 years ago Posts: 501 |
Re: Boot Debian from SATA (GoFlex Net) March 27, 2012 04:36PM |
Registered: 12 years ago Posts: 17 |
Re: Boot Debian from SATA (GoFlex Net) March 27, 2012 05:24PM |
Registered: 12 years ago Posts: 501 |
Re: Boot Debian from SATA (GoFlex Net) March 27, 2012 05:32PM |
Registered: 12 years ago Posts: 17 |
Re: Boot Debian from SATA (GoFlex Net) March 27, 2012 11:40PM |
Registered: 12 years ago Posts: 501 |
Re: Boot Debian from SATA (GoFlex Net) April 01, 2012 07:58AM |
Registered: 12 years ago Posts: 17 |
U-Boot 2010.09 (Feb 16 2011 - 18:42:02) UBIT v0.6 by Jeff Doozan and Peter Carmichael [cut out USB setup. -baafie] Reset IDE: Bus 0: not available Bus 1: OK Device 1: Model: <�<�<�<�<�<�<�<�<�<�<�<�<�<�<�<�<�<�<�<� Firm: <�<�<�<� Ser#: <�<�<�<�<�<�<�<�<�<� Type: Hard Disk Supports 48-bit addressing Capacity: 495943.5 MB = 484.3 GB (1015692426 x 512) IDE read: device 1 not ready IDE read: device 1 not ready ** Bad partition 1 ** ** Bad partition 1 ** No Powersaving mode 7F Error (no IRQ) dev 0 blk 0: status 0x7f ** Can't read from device 0 ** ** Unable to use ide 0:1 for fatload ** No Powersaving mode 7F Error (no IRQ) dev 0 blk 0: status 0x7f ** Can't read from device 0 ** ** Unable to use ide 0:1 for fatload ** ** Bad partition 1 ** ** Bad partition 1 ** IDE read: device 1 not ready ** Can't read from device 1 ** ** Unable to use ide 1:1 for fatload ** IDE read: device 1 not ready ** Can't read from device 1 ** ** Unable to use ide 1:1 for fatload ** UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:ramdisk", error -19 Error reading superblock on volume 'ubi:ramdisk'! UBIFS not mounted, use ubifs mount to mount volume first! Marvell>> ide reset ide reset Reset IDE: Bus 0: not available Bus 1: ............................................................** Timeout **
Re: Boot Debian from SATA (GoFlex Net) April 01, 2012 04:59PM |
Registered: 12 years ago Posts: 17 |
Re: Boot Debian from SATA (GoFlex Net) April 02, 2012 04:55PM |
Registered: 12 years ago Posts: 501 |
Re: Boot Debian from SATA (GoFlex Net) April 17, 2012 03:06AM |
Registered: 13 years ago Posts: 25 |
fw_setenv sata_boot 'ide reset; mw 0x800000 0 1; ext2load ide 0:1 0x800000 /boot/uImage; if ext2load ide 0:1 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi' fw_setenv sata_bootcmd 'run usb_set_bootargs; run sata_boot' fw_setenv bootcmd 'usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run sata_bootcmd; run rescue_bootcmd; run pogo_bootcmd; reset'
Re: Boot Debian from SATA (GoFlex Net) April 21, 2012 09:34PM |
Registered: 12 years ago Posts: 501 |
deX
Re: Boot Debian from SATA (GoFlex Net) May 27, 2012 11:00AM |
Re: Boot Debian from SATA (GoFlex Net) May 27, 2012 11:52AM |
Registered: 12 years ago Posts: 501 |
deX
Re: Boot Debian from SATA (GoFlex Net) May 27, 2012 01:24PM |
dpkg -i linux-image-3.3.2-kirkwood-dg_1.1_armel.deb5)Then..
cd /boot mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-3.3.2 -d vmlinuz-3.3.2-kirkwood-dg uImage mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-3.3.2-kirkwood-dg -d initrd.img-3.3.2-kirkwood-dg uInitrd6) Reboot..
Re: Boot Debian from SATA (GoFlex Net) May 27, 2012 01:48PM |
Registered: 12 years ago Posts: 501 |