Debian on Synology RS816 (Armada 385) January 13, 2019 06:32AM |
Registered: 5 years ago Posts: 41 |
BootROM - 1.73 Booting from SPI flash General initialization - Version: 1.0.0 AVS selection from EFUSE disabled (Skip reading EFUSE values) Detected Device ID 6820 High speed PHY - Version: 2.0 Init Synology board board SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 0 | SGMII0 | | 1 | 6 | SATA0 | | 2 | 5 | PCIe1 | | 3 | 0 | SGMII2 | | 4 | 5 | USB3 HOST0 | | 5 | 5 | USB3 HOST1 | ------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.46.0 WARNING:Wrong configuration for pup #1 CS mask and CS mirroring for all pups should be the same WARNING:Wrong configuration for pup #3 CS mask and CS mirroring for all pups should be the same DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-g74a026b-dirty (Dec 30 2015 - 14:40:58) Marvell version: 2015_T1.0p16 Board: SYNO-RS816 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1866 [MHz] L2 @ 933 [MHz] TClock @ 200 [MHz] DDR3 @ 933 [MHz] DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB MMC: mv_sdh: 0 SF: Detected N25Q64 with page size 64 KiB, total 8 MiB PCI-e 1 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0 USB3.0 0: Host Mode USB3.0 1: Host Mode Map: Code: 0x3ff3b000:0x3ffc91bc BSS: 0x3ffef688 Stack: 0x3fa2af20 Heap: 0x3fa2b000:0x3ff3b000 U-Boot Environment: 0x007e0000:0x007f0000 (SPI) Board configuration detected: Synology Model: RS816 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | SGMII | 0x01 | | egiga2 | SGMII | 0x00 | egiga0 [PRIME], egiga2 Press Ctrl+C to abort autoboot in 3 second
Marvell>> printenv CASset=max MALLOC_len=5 MPmode=SMP ata_hdd_detect=syno_hdd_detect=39,39,39,39 ata_hdd_enable=syno_hdd_enable=37,37,37,37 autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs= bootargs_dflt=$console $nandEcc $mtdparts_lgcy $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=mw 0xf10a2620 0x251;mw 0xf10a2e20 0x251;usb xhciinit; run bootspi bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts_lgcy $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootm $loadaddr; bootdelay=3 bootftp=run syno_bootargs;tftpboot $loadaddr_kernel $file_kernel;tftpboot $loadaddr_rootfs $file_rootfs;sf probe; sf read $loadaddr_dt $spi_pt_addr_dt $spi_pt_size_dt;fdt addr $loadaddr_dt;bootm $loadaddr_kernel $loadaddr_rootfs $loadaddr_dt; bootspi=run syno_bootargs;sf probe 0 50000000;sf read $loadaddr_kernel $spi_pt_addr_kernel $spi_pt_size_kernel;sf read $loadaddr_rootfs $spi_pt_addr_rootfs $spi_pt_size_rootfs;sf read $loadaddr_dt $spi_pt_addr_dt $spi_pt_size_dt;bootm $loadaddr_kernel $loadaddr_rootfs $loadaddr_dt; cacheShare=no clean_env=sf probe; sf erase $spi_pt_addr_env $spi_pt_size_env; console=console=ttyS0,115200 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:13:27:4d eth1mtu=1500 eth2addr=00:50:43:13:27:4d eth2mtu=1500 eth3addr=00:50:43:27:27:13 eth3mtu=1500 ethact=egiga0 ethaddr=00:50:43:27:27:4d ethmtu=1500 ethprime=egiga0 fdt_addr=2040000 fdt_skip_update=yes fdtaddr=0x1000000 fdtfile=armada-38x.dtb file_flash=armada38x/flash.bin file_kernel=armada38x/uImage file_rootfs=armada38x/rd.bin file_uboot=armada38x/uboot.bin ide_path=/ image_name=uImage initrd_high=8000000 initrd_name=uInitrd kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 limit_dram_size=yes loadaddr=0x02000000 loadaddr_dt=0x1000000 loadaddr_kernel=0x2000000 loadaddr_rootfs=0x3000000 loads_echo=0 mtdids=spi0=spi_flash mtdparts=mtdparts=spi0.0:4m(boot),-(spi-rootfs) mtdparts_lgcy=mtdparts=spi_flash:4m(boot),-(spi-rootfs) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:4d:27:13 netbsd_en=no netretry=no pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ run_script=no sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr sd_detection_dat3=no spi_pt_addr_dt=0x0E0000 spi_pt_addr_env=0x7e0000 spi_pt_addr_kernel=0x0F0000 spi_pt_addr_rootfs=0x3C0000 spi_pt_size_dt=0x010000 spi_pt_size_env=0x010000 spi_pt_size_kernel=0x2D0000 spi_pt_size_rootfs=0x410000 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts_lgcy root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial syno_boot_dev=/dev/md0 syno_bootargs=setenv bootargs console=ttyS0,115200 ip=off initrd=$loadaddr_rootfs root=$syno_boot_dev rw $syno_extra_args syno_hw_version=$syno_hw_version hd_power_on_seq=$syno_hdd_powerup_seq ihd_num=$syno_hdd_powerup_seq netif_num=$syno_net_if_num $ata_hdd_detect $ata_hdd_enable flash_size=8 syno_extra_args=HddHotplug=4 sata_remap=0>4:4>0 syno_hdd_powerup_seq=4 syno_hw_version=RS816 syno_net_if_num=2 upd_flash=setenv tftpfile $file_flash; tftpboot $loadaddr $tftpfile; if test $? -eq 0; then echo "This may take a while, please be patient..."; sf probe; sf erase 0 +$filesize; sf write $loadaddr 0 $filesize; echo "\ Flash Update Done"; fi; upd_kernel=setenv tftpfile $file_kernel; mw.b $loadaddr 0xFF $spi_pt_size_kernel; tftpboot $loadaddr $tftpfile; if test $? -eq 0; then sf probe; sf erase $spi_pt_addr_kernel $spi_pt_size_kernel; sf write $loadaddr $spi_pt_addr_kernel $spi_pt_size_kernel; echo "\ Kernel Update Done"; fi; upd_rootfs=setenv tftpfile $file_rootfs; mw.b $loadaddr 0xFF $spi_pt_size_rootfs; tftpboot $loadaddr $tftpfile; if test $? -eq 0; then sf probe; sf erase $spi_pt_addr_rootfs +$filesize; sf write $loadaddr $spi_pt_addr_rootfs $filesize; echo "\ Rootfs Update Done"; fi; upd_uboot=setenv tftpfile $file_uboot; tftpboot $loadaddr $tftpfile; if test $? -eq 0; then sf probe; sf erase 0 +$filesize; sf write $loadaddr 0 $filesize; echo "\ Uboot Update Done"; fi; usb0Mode=host usbActive=0 usbType=2 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 5734/65532 bytes
Marvell>> bdinfo arch_number = 0x00000210 boot_params = 0x00000100 DRAM bank = 0x00000000 -> start = 0x00000000 -> size = 0x40000000 DRAM bank = 0x00000001 -> start = 0x00000000 -> size = 0x00000000 ethaddr = 00:50:43:27:27:4d ip_addr = <NULL> baudrate = 115200 bps TLB addr = 0x3FFF0000 relocaddr = 0x3FF3B000 reloc off = 0x3FF3B000 irq_sp = 0x3FA2AF30 sp start = 0x3FA2AF20 FB base = 0x00000000
Marvell>> flash_part_print SF: Detected N25Q64 with page size 64 KiB, total 8 MiB Linux/vxWorks partitions on spi flash -------------------------------------- Spi flash Address (rx) : 0xf4000000 Spi flash size : 8MB u-boot : offset=0x00000000, size=0x00200000 (2MB) kernel/vxWorks-image : offset=0x00200000, size=0x00400000 (4MB) Linux rootfs : offset=0x00600000, size=0x00200000 (2MB) Single Image : offset=0x00200000, size=0x00600000 (6MB)
Marvell>> boot (Re)start USB controller... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 USB1: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 SF: Detected N25Q64 with page size 64 KiB, total 8 MiB ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-3.10.105 Created: 2018-12-25 10:24:34 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2558456 Bytes = 2.4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 03000000 ... Image Name: synology_armada38x_rs816 23824 Created: 2018-12-25 10:50:38 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 3632827 Bytes = 3.5 MiB Load Address: 08000000 Entry Point: 08000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x01000000 Loading Kernel Image ... OK OK Loading Ramdisk to 07c89000, end 07fffebb ... OK Loading Device Tree to 00ff9000, end 00fffa9b ... OK Skipping Device Tree update ('fdt_skip_update' = yes) Limit DDR size at 3GB due to power of 2 requirement of Address decoding Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.105 (root@build4) (gcc version 4.9.3 20150311 (prerelease) (crosstool-NG 1.20.0) ) #23824 SMP Tue Dec 25 18:23:47 CST 2018 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: Synology RS816 [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] PERCPU: Embedded 7 pages/cpu @80eda000 s7168 r8192 d13312 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 [ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x3000000 root=/dev/md0 rw HddHotplug=4 sata_remap=0>4:4>0 syno_hw_version=RS816 hd_power_on_seq=4 ihd_num=4 netif_num=2 syno_hdd_detect=39,39,39,39 syno_hdd_enable=37,37,37,37 flash_size=8 [ 0.000000] Support HDD Hotplug. [ 0.000000] SYNO: sata remap initialized [ 0.000000] Synology Hardware Version: RS816-j [ 0.000000] Internal HD num: 4 [ 0.000000] Internal netif num: 2 [ 0.000000] SYNO GPIO hdd detect pin: 39 39 39 39 [ 0.000000] SYNO GPIO hdd enable pin: 37 37 37 37 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] allocated 2097152 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 1024MB = 1024MB total [ 0.000000] Memory: 1026876k/1026876k available, 21700k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc0800000 - 0xfff00000 (1015 MB) [ 0.000000] lowmem : 0x80000000 - 0xc0000000 (1024 MB) [ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB) [ 0.000000] .text : 0x80008000 - 0x805f7078 (6077 kB) [ 0.000000] .init : 0x805f8000 - 0x80631c00 ( 231 kB) [ 0.000000] .data : 0x80632000 - 0x80668a40 ( 219 kB) [ 0.000000] .bss : 0x80668a40 - 0x806cec84 ( 409 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] [ 0.000000] LSP version: linux-3.10.70-2015_T1.1p7 [ 0.000000] [ 0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms [ 0.000000] L310 cache controller enabled [ 0.000000] l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B [ 0.000333] Calibrating delay loop... 3719.16 BogoMIPS (lpj=18595840) [ 0.060016] pid_max: default: 32768 minimum: 301 [ 0.060054] Security Framework initialized [ 0.060062] AppArmor: AppArmor initialized [ 0.060076] Mount-cache hash table entries: 512 [ 0.060337] Initializing cgroup subsys memory [ 0.060350] Disabling memory control group subsystem [ 0.060353] Initializing cgroup subsys devices [ 0.060356] Initializing cgroup subsys freezer [ 0.060359] Initializing cgroup subsys blkio [ 0.060377] CPU: Testing write buffer coherency: ok [ 0.060464] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.060467] Calibrating local timer... 933.17MHz. [ 0.120040] Setting up static identity map for 0x8047a190 - 0x8047a1e8 [ 0.120142] mvebu-pmsu: Initializing Power Management Service Unit [ 0.120166] Initializing CPU Reset module [ 0.120651] CPU1: Booted secondary processor [ 0.180035] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.180079] Brought up 2 CPUs [ 0.180085] SMP: Total of 2 processors activated (7445.70 BogoMIPS). [ 0.180088] CPU: All CPU(s) started in SVC mode. [ 0.180306] devtmpfs: initialized [ 0.182059] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 [ 0.182200] xor: measuring software checksum speed [ 0.279995] arm4regs : 3314.800 MB/sec [ 0.379978] 8regs : 2284.400 MB/sec [ 0.479961] 32regs : 2324.000 MB/sec [ 0.479963] xor: using function: arm4regs (3314.800 MB/sec) [ 0.479967] pinctrl core: initialized pinctrl subsystem [ 0.480180] regulator-dummy: no parameters [ 0.480301] NET: Registered protocol family 16 [ 0.480737] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.482369] irq: Cannot allocate irq_descs @ IRQ195, assuming pre-allocated [ 0.482631] irq: Cannot allocate irq_descs @ IRQ227, assuming pre-allocated [ 0.484727] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.484731] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.490332] bio: create slab <bio-0> at 0 [ 0.659950] raid6: int32x1 gen() 279 MB/s [ 0.830046] raid6: int32x1 xor() 231 MB/s [ 0.999893] raid6: int32x2 gen() 383 MB/s [ 1.169886] raid6: int32x2 xor() 260 MB/s [ 1.339819] raid6: int32x4 gen() 384 MB/s [ 1.509822] raid6: int32x4 xor() 276 MB/s [ 1.679822] raid6: int32x8 gen() 425 MB/s [ 1.849818] raid6: int32x8 xor() 272 MB/s [ 1.849821] raid6: using algorithm int32x8 gen() (425 MB/s) [ 1.849823] raid6: .... xor() 272 MB/s, rmw enabled [ 1.849825] raid6: using intx1 recovery algorithm [ 1.849960] mvebu-pcie pcie-controller.3: PCIe1.0: link up [ 1.850056] mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 [ 1.850063] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.850067] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.850071] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.850178] PCI: bus0: Fast back to back transfers disabled [ 1.850183] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.850421] PCI: bus1: Fast back to back transfers disabled [ 1.850453] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff] [ 1.850458] pci 0000:00:02.0: BAR 7: assigned [io 0x10000-0x10fff] [ 1.850463] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref] [ 1.850468] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0010000-0xe00107ff] [ 1.850473] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1001f] [ 1.850477] pci 0000:01:00.0: BAR 0: assigned [io 0x10020-0x10027] [ 1.850482] pci 0000:01:00.0: BAR 2: assigned [io 0x10028-0x1002f] [ 1.850486] pci 0000:01:00.0: BAR 1: assigned [io 0x10030-0x10033] [ 1.850491] pci 0000:01:00.0: BAR 3: assigned [io 0x10034-0x10037] [ 1.850495] pci 0000:00:02.0: PCI bridge to [bus 01] [ 1.850499] pci 0000:00:02.0: bridge window [io 0x10000-0x10fff] [ 1.850510] pci 0000:00:02.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.850517] PCI: enabling device 0000:00:02.0 (0140 -> 0143) [ 1.850913] SCSI subsystem initialized [ 1.851748] Switching to clocksource armada_370_xp_clocksource [ 1.851893] AppArmor: AppArmor Filesystem Enabled [ 1.852703] NET: Registered protocol family 2 [ 1.852966] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 1.853020] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 1.853072] TCP: Hash tables configured (established 8192 bind 8192) [ 1.853102] TCP: reno registered [ 1.853108] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 1.853123] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 1.853205] NET: Registered protocol family 1 [ 1.853321] RPC: Registered named UNIX socket transport module. [ 1.853325] RPC: Registered udp transport module. [ 1.853327] RPC: Registered tcp transport module. [ 1.853329] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.853347] pci 0000:01:00.0: Apply mv9235 specific programming steps [ 1.853438] Trying to unpack rootfs image as initramfs... [ 2.746179] Freeing initrd memory: 3544K (87c89000 - 87fff000) [ 2.746362] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 2.747522] Initialise module verification [ 2.747555] audit: initializing netlink socket (disabled) [ 2.747585] type=2000 audit(2.740:1): initialized [ 2.748541] VFS: Disk quotas dquot_6.5.2 [ 2.748583] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.748806] NFS: Registering the id_resolver key type [ 2.748819] Key type id_resolver registered [ 2.748822] Key type id_legacy registered [ 2.748838] msgmni has been set to 2012 [ 2.749286] async_tx: api initialized (async) [ 2.749292] Key type asymmetric registered [ 2.749295] Asymmetric key parser 'x509' registered [ 2.749440] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 2.749445] io scheduler noop registered [ 2.749456] io scheduler cfq registered (default) [ 2.750112] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 2.750508] mv_xor f1060800.xor: Marvell shared XOR driver [ 2.782009] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq ) [ 2.812031] mv_xor f1060800.xor: freeing 1 in use descriptors! [ 2.812039] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( intr crc32c ) [ 2.812892] mv_xor f1060900.xor: Marvell shared XOR driver [ 2.851994] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq ) [ 2.882016] mv_xor f1060900.xor: freeing 1 in use descriptors! [ 2.882024] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( intr crc32c ) [ 2.883260] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.904760] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A [ 3.785664] console [ttyS0] enabled [ 3.809589] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 45) is a 16550A [ 3.823908] brd: module loaded [ 3.826977] Loading iSCSI transport class v2.0-870. [ 3.833505] Change defer qc mode on external port for compatibility [ 3.839796] Change defer qc mode on external port for compatibility [ 3.846097] Change defer qc mode on external port for compatibility [ 3.852395] Change defer qc mode on external port for compatibility [ 3.871871] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode [ 3.879997] ahci 0000:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.890991] scsi0 : ahci [ 3.893987] scsi1 : ahci [ 3.896866] scsi2 : ahci [ 3.899812] scsi3 : ahci [ 3.902716] ata1: SATA max UDMA/133 abar m2048@0xe0010000 port 0xe0010100 irq 65 [ 3.910143] ata2: SATA max UDMA/133 abar m2048@0xe0010000 port 0xe0010180 irq 65 [ 3.917580] ata3: SATA max UDMA/133 abar m2048@0xe0010000 port 0xe0010200 irq 65 [ 3.925022] ata4: SATA max UDMA/133 abar m2048@0xe0010000 port 0xe0010280 irq 65 [ 4.281776] ata1: SATA link down (SStatus 0 SControl 300) [ 4.287196] ata1: No present pin info for SATA link down event [ 4.641775] ata2: SATA link down (SStatus 0 SControl 300) [ 4.647194] ata2: Disk is not present for SATA link down event [ 5.001776] ata3: SATA link down (SStatus 0 SControl 300) [ 5.007195] ata3: Disk is not present for SATA link down event [ 5.361775] ata4: SATA link down (SStatus 0 SControl 300) [ 5.367194] ata4: Disk is not present for SATA link down event [ 5.373515] ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 5.382351] ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 5.392272] scsi4 : ahci_mv_platform [ 5.396254] scsi5 : ahci_mv_platform [ 5.400172] ata5: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 [ 5.408144] ata6: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 [ 5.761771] ata5: SATA link down (SStatus 0 SControl 300) [ 5.767191] ata5: Disk is not present for SATA link down event [ 6.121770] ata6: SATA link down (SStatus 0 SControl 300) [ 6.127189] ata6: No present pin info for SATA link down event [ 6.135392] m25p80 spi0.0: n25q064 (8192 Kbytes) [ 6.140037] Searching for RedBoot partition table in spi0.0 at offset 0x7f0000 [ 6.243212] 6 RedBoot partitions found on MTD device spi0.0 [ 6.248807] Creating 6 MTD partitions on "spi0.0": [ 6.253644] 0x000000000000-0x0000000f0000 : "RedBoot" [ 6.259574] 0x0000000f0000-0x0000003c0000 : "zImage" [ 6.265442] 0x0000003c0000-0x0000007d0000 : "rd.gz" [ 6.271109] 0x0000007d0000-0x0000007e0000 : "vendor" [ 6.276484] vender Mac0 address : 00:11:32:88:5d:cb [ 6.281382] vender Mac1 address : 00:11:32:88:5d:cc [ 6.286289] vender Mac2 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 6.292147] vender Mac3 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 6.298003] serial number='1810NWN991200' [ 6.302638] 0x0000007e0000-0x0000007f0000 : "RedBoot Config" [ 6.309425] 0x0000007f0000-0x000000800000 : "FIS directory" [ 6.318236] SoC: model = 0x6820, revision = 0x4 [ 6.322860] mvPncVirtBase = 0xc0c00000, pncTcamSize = 1024 [ 6.328366] o 3 Giga ports supported [ 6.332139] o SKB recycle supported for SWF (Disabled) [ 6.337470] o NETA acceleration mode 4 [ 6.341405] o BM supported for CPU: 4 BM pools [ 6.346042] o PnC supported (Enabled) [ 6.349890] o RX Queue support: 8 Queues * 512 Descriptors [ 6.355573] o TX Queue support: 8 Queues * 1024 Descriptors [ 6.361338] o GSO supported [ 6.364316] o GRO supported [ 6.367292] o Receive checksum offload supported [ 6.372102] o Transmit checksum offload supported [ 6.376996] o Driver ERROR statistics enabled [ 6.381542] o Driver INFO statistics enabled [ 6.386003] o Driver DEBUG statistics enabled [ 6.390548] [ 6.392921] port #0: is_sgmii=1, is_rgmii=0, phy_addr=1 [ 6.398192] o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 [ 6.406510] [ 6.408004] o Port 0 is connected to Linux netdevice [ 6.416646] o eth0, ifindex = 2, GbE port = 0 [ 6.421382] o eth0, phy chipid = 1410dd0, Support WOL = 32 [ 6.430659] giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform) [ 6.436799] [ 6.438372] port #2: is_sgmii=1, is_rgmii=0, phy_addr=0 [ 6.443626] o Loading network interface(s) for port #2: cpu_mask=0x3, tx_csum_limit=2048 [ 6.451939] [ 6.453432] o Port 2 is connected to Linux netdevice [ 6.461948] o eth1, ifindex = 3, GbE port = 2 [ 6.466683] o eth1, phy chipid = 1410dd0, Support WOL = 32 [ 6.475964] giga p=2: mtu=1500, mac=00:50:43:02:02:03 (platform) [ 6.482090] [ 6.483987] libphy: orion_mdio_bus: probed [ 6.492109] mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 6.551910] i2c /dev entries driver [ 7.355542] Syno_HddMon: Initialization completed. [ 7.370416] armada_thermal f10e4078.thermal: Overheat threshold between 92..107 [ 7.378375] md: linear personality registered for level -1 [ 7.383895] md: raid0 personality registered for level 0 [ 7.389228] md: raid1 personality registered for level 1 [ 7.394567] md: raid10 personality registered for level 10 [ 7.400239] md: raid6 personality registered for level 6 [ 7.405582] md: raid5 personality registered for level 5 [ 7.410913] md: raid4 personality registered for level 4 [ 7.416428] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-devel@redhat.com [ 7.424912] cpuidle: using governor ladder [ 7.429231] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 [ 7.438592] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) [ 7.447051] mvCesaInit: channels=2, session=640, queue=256 [ 7.460704] armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode [ 7.470044] cesadev_init(80616ae0) [ 7.474039] TCP: cubic registered [ 7.477369] NET: Registered protocol family 17 [ 7.481876] Key type dns_resolver registered [ 7.486223] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 7.493943] Registering suspend init for this board failed [ 7.501510] Loading module verification blacklist certificates [ 7.507400] Loading module verification certificates [ 7.512443] MODSIGN: Loaded cert 'Synology SDG kernel module signing key: 7bd0b0d6bcd31651c22ce3978bdc8c8bdc417329' [ 7.526613] MODSIGN: Loaded cert 'Synology Root Certification Authority: f2c075361f168425f8b5ef31b796406c3aab2089' [ 7.537034] MODSIGN: Loaded cert 'Synology Kernel Module Signing Certification Authority: 600839b5d127e0e11d817a31f0575d323a7c0e28' [ 7.548931] MODSIGN: Loaded cert 'Synology kernel module signing key: 4646ce54489669338118a3b1286da156ac366fa5' [ 7.559074] registered taskstats version 1 [ 7.563236] regulator-dummy: disabling [ 7.567250] Freeing unused kernel memory: 228K (805f8000 - 80631000) START /linuxrc.syno Insert basic USB modules... :: Loading module usb-common ... [ OK ] :: Loading module usbcore[ 7.679472] usbcore: registered new interface driver usbfs [ 7.686002] usbcore: registered new interface driver hub [ 7.695190] usbcore: registered new device driver usb ... [ OK ] :: Loading module ehci-hcd[ 7.724397] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ... [ OK ] :: Loading module xhci-hcd[ 7.757430] xhci-hcd f10f0000.usb3: USB2 Vbus gpio 58 [ 7.762524] xhci-hcd f10f0000.usb3: power control enabled [ 7.767951] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 7.773304] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 1 [ 7.780940] xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 [ 7.787221] hub 1-0:1.0: USB hub found [ 7.790997] hub 1-0:1.0: 1 port detected [ 7.795043] xhci-hcd f10f0000.usb3: USB3 Vbus gpio 58 [ 7.800120] xhci-hcd f10f0000.usb3: power control enabled [ 7.805577] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 7.810924] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 7.820732] hub 2-0:1.0: USB hub found [ 7.824533] hub 2-0:1.0: 1 port detected [ 7.828659] xhci-hcd f10f8000.usb3: USB2 Vbus gpio 59 [ 7.833751] xhci-hcd f10f8000.usb3: power control enabled [ 7.839178] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 7.844551] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3 [ 7.852242] xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 [ 7.858537] hub 3-0:1.0: USB hub found [ 7.862331] hub 3-0:1.0: 1 port detected [ 7.866353] xhci-hcd f10f8000.usb3: USB3 Vbus gpio 59 [ 7.871430] xhci-hcd f10f8000.usb3: power control enabled [ 7.876874] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 7.882226] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 7.890450] hub 4-0:1.0: USB hub found [ 7.894259] hub 4-0:1.0: 1 port detected ... [ OK ] :: Loading module ehci-orion[ 7.937726] ehci-orion: EHCI orion driver [ 7.941882] orion-ehci f1058000.usb: failed to get Vbus gpio [ 7.947569] orion-ehci f1058000.usb: USB2 Vbus gpio -1 [ 7.952739] orion-ehci f1058000.usb: power control disabled [ 7.958332] orion-ehci f1058000.usb: EHCI Host Controller [ 7.963763] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 5 [ 7.971407] orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 [ 7.991805] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 7.998238] hub 5-0:1.0: USB hub found [ 8.002060] hub 5-0:1.0: 1 port detected ... [ OK ] insmod: can't insert '/lib/modules/etxhci-hcd.ko': No such file or directory Insert net driver([ 8.045917] rs816_synobios: module license 'Synology Inc.' taints kernel. Mindspeed only).[ 8.054098] Disabling lock debugging due to kernel taint .. [ 8.061641] Synobios RS816 GPIO initialized [ 8.066051] 2019-1-13 11:29:19 UTC [ 8.069469] synobios: load, major number 201 [ 8.073765] Brand: Synology [ 8.076587] Model: RS-816 [ 8.079225] This is default settings: set group disks wakeup number to 1, spinup time deno 1 [ 8.087714] synobios cpu_arch proc entry initialized [ 8.092701] synobios crypto_hw proc entry initialized [ 8.097773] synobios syno_platform proc entry initialized [ 8.103253] synobios open /dev/ttyS1 success Starting /usr/syno/bin/synocfgen... /usr/syno/bin/synocfgen returns 0 [ 8.118224] synobios: unload Exit on error [1] DISK NOT INSTALLED... Sun Jan 13 11:29:19 UTC 2019 none /sys/kernel/debug debugfs rw,relatime 0 0 sys /sys sysfs rw,relatime 0 0 none /dev devtmpfs rw,relatime,size=513436k,nr_inodes=128359,mode=755 0 0 proc /proc proc rw,relatime 0 0 linuxrc.syno failed on 1 starting pid 901, tty '': '/etc/rc' :: Starting /etc/rc :: Mounting procfs ... [ OK ] :: Mounting tmpfs ... [ OK ] :: Mounting devtmpfs ... [ OK ] :: Mounting devpts ... [ OK ] :: Mounting sysfs ... [ OK ] mdadm: error opening /dev/md1: No such file or directory rc: Use all internal disk as swap. rc: No internal disk installed. swapon: can't stat '/dev/md1': No such file or directory :: Loading module fat ... [ OK ] :: Loading module vfat ... [ OK ] :: Loading module synobios[ 8.593832] Synobios RS816 GPIO initialized [ 8.598228] 2019-1-13 11:29:19 UTC [ 8.601646] synobios: load, major number 201 [ 8.605954] Brand: Synology [ 8.608776] Model: RS-816 [ 8.611414] This is default settings: set group disks wakeup number to 1, spinup time deno 1 [ 8.619905] synobios cpu_arch proc entry initialized [ 8.624893] synobios crypto_hw proc entry initialized [ 8.629964] synobios syno_platform proc entry initialized [ 8.635441] synobios open /dev/ttyS1 success ... [ OK ] [ 8.767885] eth0: mac address changed [ 8.786463] eth1: mac address changed [ 8.810378] pool #0: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added [ 8.817884] eth0: started udhcpc (v1.16.1) started [ 9.876118] pool #2: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added [ 9.883635] eth1: started udhcpc (v1.16.1) started eth0 Link encap:Ethernet HWaddr 00:11:32:88:5D:CB UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1024 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:193 eth1 Link encap:Ethernet HWaddr 00:11:32:88:5D:CC UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1024 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:194 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) :: Starting syslogd ... [ OK ] /etc/rc: line 262: /usr/syno/bin/syno_pstore_collect: not found :: Starting scemd :: Starting services in background Starting findhostd in flash_rd... Starting services in flash_rd... Running /usr/syno/etc/rc.d/J01httpd.sh... Starting httpd:80 in flash_rd... Starting httpd:5000 in flash_rd... Running /usr/syno/etc/rc.d/J03ssdpd.sh... /usr/bin/minissdpd -i eth0 -i eth1 eth0 not RUNNING eth1 not RUNNING Running /usr/syno/etc/rc.d/J04synoagentregisterd.sh... Starting synoagentregisterd... Running /usr/syno/etc/rc.d/J30DisableNCQ.sh... cat: can't open '/sys/block/sd*/device//model': No such file or directory Running /usr/syno/etc/rc.d/J80ADTFanControl.sh... Running /usr/syno/etc/rc.d/J98nbnsd.sh... Starting nbnsd... Running /usr/syno/etc/rc.d/J99avahi.sh... Starting Avahi mDNS/DNS-SD Daemon cname_load_conf failed:/var/tmp/nginx/avahi-aliases.conf :: Loading module usb-storage[ 18.236645] usbcore: registered new interface driver usb-storage ... [ OK ] ============ Date ============ Sun Jan 13 11:2 Sun Jan 13 11:29:29 2019 RackStation login:
Marvell>> help ? - alias for 'help' Creset - Creset - Run 'reset' or boot command in a loop, while counting. SatR - Sample At Reset sub-system WOLTest - WOLTest - Wake On Lan u-boot testing active_units- print active units on board base - print or set address offset bdinfo - print Board Info structure boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootelf - Boot from an ELF image in memory bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol bootvx - Boot vxWorks from an ELF image bootz - boot Linux zImage image from memory cmp - memory compare coninfo - print console devices and information cp - memory copy cpss_env- set cpss environment variables permanently crc32 - checksum calculation date - get/set/reset date & time ddrPhyRead- ddrPhyRead - Read DDR PHY register ddrPhyWrite- ddrPhyWrite - Write DDR PHY register dhcp - boot image via network using DHCP/TFTP protocol diskboot- diskboot- boot from IDE device dma - dma - Perform DMA using the XOR engine echo - echo args to console editenv - edit environment variable eeprom - EEPROM sub-system env - environment handling commands exit - exit script false - do nothing, unsuccessfully fdt - flattened device tree utility commands flash_part_print- flash_part_print - print spi/nand FLASH memory information go - start application at address 'addr' help - print command description/usage i2c - I2C sub-system ide - ide - IDE sub-system iminfo - print header information for application image imxtract- extract a part of a multi-image ir - ir - reading and changing MV internal register values. itest - return true/false on integer compare loadb - load binary file over serial line (kermit mode) loads - load S-Record file over serial line loadx - load binary file over serial line (xmodem mode) loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range map - map - Display address decode windows md - memory display me - me - PCIe master enable mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - display MMC info mp - mp - map PCIe BAR mtdburn - Burn a Linux image and Filesystem` on the NAND/SPI flash. mtest - simple RAM read/write test mw - memory write (fill) nfs - boot image via network using NFS protocol nm - memory modify (constant address) pci - list and access PCI Configuration Space pciePhyRead- phyRead - Read PCI-E Phy register pciePhyWrite- pciePhyWrite - Write PCI-E Phy register phyRead - phyRead - Read Phy register phyWrite- phyWrite - Write Phy register ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables pxe - commands to get and boot from pxe files qsgmii_sel- Select SFP or QSGMII modes on bc2. rcvr - rcvr - Start recovery process (with TFTP server) reset - Perform RESET of the CPU resetenv- resetenv - Erase environment sector to reset all variables to default. run - run commands in an environment variable saveenv - save environment variables to persistent storage scsi - SCSI sub-system scsiboot- boot from SCSI device se - se - PCIe Slave enable setenv - set environment variables sf - SPI flash sub-system sg - sg - scanning the PHYs status showvar - print local hushshell variables sleep - delay execution for some time smiscan - smiscan - Scan for marvell smi devices. source - run script from memory sp - scan and detect all devices on PCI-e interface sspi - SPI utility command switchCountersRead- switchCntPrint - Read switch port counters. switchPhyRegRead- - Read switch register switchPhyRegWrite- - Write switch register switchRegRead- switchRegRead - Read switch register switchRegWrite- switchRegWrite - Write switch register syno_pwoff- syno_pwoff - bring the system down syno_up - syno_up - Send a character to microp sysboot - command to get and boot from syslinux files temp - temp - Display the device temperature. tempCmd0- tempCmd - This command allocated for monitor extinction tempCmd1- tempCmd - This command allocated for monitor extinction tempCmd2- tempCmd - This command allocated for monitor extinction tempCmd3- tempCmd - This command allocated for monitor extinction test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol training- training - prints the results of the DDR3 Training. trainingStability- training - prints the results of the DDR3 Training. true - do nothing, successfully ts_report- ts_report - report touch screen coordinate ts_test - ts_test - test touch screen usb - USB sub-system usbboot - boot from USB device version - print monitor, compiler and linker version whoAmI - - reading CPU ID Marvell>>
Re: Debian on Synology RS816 (Armada 385) January 13, 2019 11:03AM |
Admin Registered: 13 years ago Posts: 19,102 |
U-Boot 2013.01-g74a026b-dirty (Dec 30 2015 - 14:40:58) Marvell version: 2015_T1.0p16 Board: SYNO-RS816 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE
Quote
I do not have a dts file either for the device.
Re: Debian on Synology RS816 (Armada 385) January 13, 2019 12:02PM |
Registered: 5 years ago Posts: 41 |
cp -a zImage-4.12.4-mvebu-tld-1 zImage
Re: Debian on Synology RS816 (Armada 385) January 13, 2019 12:06PM |
Registered: 5 years ago Posts: 41 |
Marvell>> usb start (Re)start USB... USB0: Error: requested 'usbActive' (0) is not connected on current board Supported Units: USB2.0: 1 ports: set usbType = 2 --> EHCI Stack will be used USB3.0: 2 ports: set usbType = 3 --> xHCI Stack will be used lowlevel init failed USB error: all controllers failed lowlevel init
Re: Debian on Synology RS816 (Armada 385) January 13, 2019 11:11PM |
Admin Registered: 13 years ago Posts: 19,102 |
Quote
Could it be possible that this is already done when unpacking the rootfs as there is already an zImage ?
cp -a zImage-4.12.4-mvebu-tld-1 zImage
Quote
Marvell>> usb start
(Re)start USB...
USB0:
Error: requested 'usbActive' (0) is not connected on current board
Supported Units:
USB2.0: 1 ports: set usbType = 2 --> EHCI Stack will be used
USB3.0: 2 ports: set usbType = 3 --> xHCI Stack will be used
lowlevel init failed
USB error: all controllers failed lowlevel init
setenv usbActive 1 usb reset
Re: Debian on Synology RS816 (Armada 385) January 14, 2019 12:28AM |
Admin Registered: 13 years ago Posts: 19,102 |
Quote
spi_pt_addr_dt=0x0E0000
Re: Debian on Synology RS816 (Armada 385) January 14, 2019 01:57PM |
Registered: 5 years ago Posts: 41 |
Quote
At u-boot prompt, try
setenv usbActive 1
usb reset
Quote
spi_pt_addr_dt=0x0E0000
The stock DTB is stored at this location (we could extract that).
Re: Debian on Synology RS816 (Armada 385) January 14, 2019 02:07PM |
Registered: 5 years ago Posts: 41 |
Marvell>> setenv usb 'setenv usbActive 1; setenv usbType 3; usb start;' Marvell>> run usb (Re)start USB... USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found
Re: Debian on Synology RS816 (Armada 385) January 14, 2019 09:36PM |
Registered: 9 years ago Posts: 465 |
Re: Debian on Synology RS816 (Armada 385) January 14, 2019 10:53PM |
Admin Registered: 13 years ago Posts: 19,102 |
ext2ls usb 0:1 /boot
Re: Debian on Synology RS816 (Armada 385) January 14, 2019 10:57PM |
Admin Registered: 13 years ago Posts: 19,102 |
Re: Debian on Synology RS816 (Armada 385) January 15, 2019 03:21AM |
Admin Registered: 13 years ago Posts: 19,102 |
Quote
[ 0.000000] Linux version 3.10.105 (root@build4) (gcc version 4.9.3 20150311 (prerelease) (crosstool-NG 1.20.0) ) #23824 SMP Tue Dec 25 18:23:47 CST 2018
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: Synology RS816
Re: Debian on Synology RS816 (Armada 385) January 15, 2019 04:04AM |
Registered: 5 years ago Posts: 41 |
Re: Debian on Synology RS816 (Armada 385) January 15, 2019 04:32AM |
Admin Registered: 13 years ago Posts: 19,102 |
https://sourceforge.net/projects/dsgpl/files/Synology%20NAS%20GPL%20Source/22259branch/armada38x-source/u-boot-1.3.3.txz
Re: Debian on Synology RS816 (Armada 385) January 15, 2019 11:46AM |
Registered: 5 years ago Posts: 41 |
Re: Debian on Synology RS816 (Armada 385) January 15, 2019 12:22PM |
Admin Registered: 13 years ago Posts: 19,102 |
> sudo kwboot -t -B 115200 /dev/ttyS0 -b > uboot_RS816.bin -s 0 -q 1 >>
Re: Debian on Synology RS816 (Armada 385) January 15, 2019 12:33PM |
Registered: 5 years ago Posts: 41 |
Re: Debian on Synology RS816 (Armada 385) January 15, 2019 11:00PM |
Admin Registered: 13 years ago Posts: 19,102 |
sudo kwboot -t -B 115200 /dev/ttyS0 -b uboot_RS816.bin -p
./download-serial.sh /dev/ttyUSB0 uboot_RS816.bin
Re: Debian on Synology RS816 (Armada 385) January 16, 2019 02:46AM |
Registered: 6 years ago Posts: 125 |
Re: Debian on Synology RS816 (Armada 385) January 16, 2019 03:12AM |
Admin Registered: 13 years ago Posts: 19,102 |
Re: Debian on Synology RS816 (Armada 385) January 16, 2019 05:41AM |
Admin Registered: 13 years ago Posts: 19,102 |
mw 0xf10a2620 0x251 mw 0xf10a2e20 0x251 usb xhciinit
usb start
Re: Debian on Synology RS816 (Armada 385) January 16, 2019 08:52AM |
Registered: 5 years ago Posts: 41 |
Quote
zifxify,
Back to USB issue.
At u-boot prompt
mw 0xf10a2620 0x251
mw 0xf10a2e20 0x251
usb xhciinit
And then if the USB drive is not initialized, go ahead and start it:
usb start
Marvell>> mw 0xf10a2620 0x251 Marvell>> mw 0xf10a2e20 0x251 Marvell>> usb xhciinit (Re)start USB controller... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 USB1: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 Marvell>> usb start (Re)start USB... USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found
Re: Debian on Synology RS816 (Armada 385) January 16, 2019 09:32AM |
Admin Registered: 13 years ago Posts: 19,102 |
Re: Debian on Synology RS816 (Armada 385) January 16, 2019 10:38AM |
Registered: 5 years ago Posts: 41 |
Quote
Hey, while there’s no extload commands there is tftpboot, have you tried loading the kernel from a tftp server?
Marvell>> setenv ipaddr 172.16.10.150 Marvell>> setenv serverip 172.16.10.18 Marvell>> tftpboot *** Warning: no boot file name; using 'AC100A96.img' Using egiga0 device TFTP from server 172.16.10.18; our IP address is 172.16.10.150 Filename 'AC100A96.img'. Load address: 0x2000000 Loading: ################################################################# ################################################################# ############################################# 2.5 MiB/s done Bytes transferred = 2558520 (270a38 hex) Marvell>> bootm ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-3.10.105 Created: 2018-10-26 10:32:58 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2558456 Bytes = 2.4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. no ATAGS support: can't continue
Re: Debian on Synology RS816 (Armada 385) January 16, 2019 11:13AM |
Registered: 5 years ago Posts: 41 |
Marvell>> tftpboot 0x2000000 uImage-D Using egiga0 device TFTP from server 172.16.10.18; our IP address is 172.16.10.150 Filename 'uImage-D'. Load address: 0x2000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ############## 5.1 MiB/s done Bytes transferred = 4021360 (3d5c70 hex) Marvell>> bootm 0x2000000 ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-4.12.4-mvebu-tld-1 Created: 2017-08-22 11:09:57 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4021296 Bytes = 3.8 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: unrecognized/unsupported machine ID (r1 = 0x00000210). Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Armada 39x (Device Tree) ffffffff Marvell Armada 380/385 (Device Tree) ffffffff Marvell Armada 375 (Device Tree) ffffffff Marvell Armada 370/XP (Device Tree) ffffffff Marvell Dove Please check your kernel config and/or bootloader.
Re: Debian on Synology RS816 (Armada 385) January 16, 2019 11:17AM |
Admin Registered: 13 years ago Posts: 19,102 |
Re: Debian on Synology RS816 (Armada 385) January 16, 2019 11:18AM |
Admin Registered: 13 years ago Posts: 19,102 |
Re: Debian on Synology RS816 (Armada 385) January 17, 2019 12:00AM |
Admin Registered: 13 years ago Posts: 19,102 |
setenv usb_setup 'setenv usbActive 1; setenv usbType 3; usb start;' setenv load_dtb_addr 0x1000000 setenv load_initrd_addr 0x3000000 setenv load_image_addr 0x02000000 setenv load_image 'echo loading zImage ...; ext2load usb 0:1 $load_image_addr /boot/zImage' setenv load_initrd 'echo loading uInitrd ...; ext2load usb 0:1 $load_initrd_addr /boot/uInitrd' setenv load_dtb 'echo loading DTB from flash ...; sf probe 0 50000000; sf read $load_dtb_addr $spi_pt_addr_dt $spi_pt_size_dt' setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial"' setenv bootcmd_exec 'echo Booting Debian . . .; run usb_setup; run set_bootargs; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run load_image; run load_initrd; run load_dtb; bootz $load_image_addr $load_initrd_addr $load_dtb_addr' setenv bootcmd 'mw 0xf10a2620 0x251;mw 0xf10a2e20 0x251;usb xhciinit; run bootcmd_exec; run bootspi'
boot
Re: Debian on Synology RS816 (Armada 385) January 17, 2019 11:37AM |
Registered: 5 years ago Posts: 41 |
Marvell>> boot (Re)start USB controller... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 USB1: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 Booting Debian . . . (Re)start USB... USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading zImage ... Unknown command 'ext2load' - try 'help' loading uInitrd ... Unknown command 'ext2load' - try 'help' loading DTB from flash ... SF: Detected N25Q64 with page size 64 KiB, total 8 MiB Bad Linux ARM zImage magic! SF: Detected N25Q64 with page size 64 KiB, total 8 MiB ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-3.10.105 Created: 2018-12-25 10:24:34 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2558456 Bytes = 2.4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 03000000 ... Image Name: synology_armada38x_rs816 23824 Created: 2018-12-25 10:50:38 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 3632827 Bytes = 3.5 MiB Load Address: 08000000 Entry Point: 08000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x01000000 Loading Kernel Image ... OK OK Loading Device Tree to 00ff9000, end 00fffa9b ... OK Skipping Device Tree update ('fdt_skip_update' = yes) Limit DDR size at 3GB due to power of 2 requirement of Address decoding Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.105 (root@build4) (gcc version 4.9.3 20150311 (prerelease) (crosstool-NG 1.20.0) ) #23824 SMP Tue Dec 25 18:23:47 CST 2018 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: Synology RS816 [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] PERCPU: Embedded 7 pages/cpu @80eda000 s7168 r8192 d13312 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 [ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x3000000 root=/dev/md0 rw HddHotplug=4 sata_remap=0>4:4>0 syno_hw_version=RS816 hd_power_on_seq=4 ihd_num=4 netif_num=2 syno_hdd_detect=39,39,39,39 syno_hdd_enable=37,37,37,37 flash_size=8 [ 0.000000] Support HDD Hotplug. [ 0.000000] SYNO: sata remap initialized [ 0.000000] Synology Hardware Version: RS816-j [ 0.000000] Internal HD num: 4 [ 0.000000] Internal netif num: 2 [ 0.000000] SYNO GPIO hdd detect pin: 39 39 39 39 [ 0.000000] SYNO GPIO hdd enable pin: 37 37 37 37 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] allocated 2097152 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 1024MB = 1024MB total [ 0.000000] Memory: 1026876k/1026876k available, 21700k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc0800000 - 0xfff00000 (1015 MB) [ 0.000000] lowmem : 0x80000000 - 0xc0000000 (1024 MB) [ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB) [ 0.000000] .text : 0x80008000 - 0x805f7078 (6077 kB) [ 0.000000] .init : 0x805f8000 - 0x80631c00 ( 231 kB) [ 0.000000] .data : 0x80632000 - 0x80668a40 ( 219 kB) [ 0.000000] .bss : 0x80668a40 - 0x806cec84 ( 409 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] [ 0.000000] LSP version: linux-3.10.70-2015_T1.1p7 [ 0.000000] [ 0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms [ 0.000000] L310 cache controller enabled [ 0.000000] l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B [ 0.000334] Calibrating delay loop... 3719.16 BogoMIPS (lpj=18595840) [ 0.060016] pid_max: default: 32768 minimum: 301 [ 0.060054] Security Framework initialized [ 0.060061] AppArmor: AppArmor initialized [ 0.060075] Mount-cache hash table entries: 512 [ 0.060335] Initializing cgroup subsys memory [ 0.060347] Disabling memory control group subsystem [ 0.060350] Initializing cgroup subsys devices [ 0.060353] Initializing cgroup subsys freezer [ 0.060356] Initializing cgroup subsys blkio [ 0.060374] CPU: Testing write buffer coherency: ok [ 0.060462] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.060465] Calibrating local timer... 933.17MHz. [ 0.120037] Setting up static identity map for 0x8047a190 - 0x8047a1e8 [ 0.120138] mvebu-pmsu: Initializing Power Management Service Unit [ 0.120163] Initializing CPU Reset module [ 0.120649] CPU1: Booted secondary processor [ 0.180033] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.180077] Brought up 2 CPUs [ 0.180084] SMP: Total of 2 processors activated (7445.70 BogoMIPS). [ 0.180086] CPU: All CPU(s) started in SVC mode. [ 0.180307] devtmpfs: initialized [ 0.182061] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 [ 0.182201] xor: measuring software checksum speed [ 0.279993] arm4regs : 3314.800 MB/sec [ 0.379976] 8regs : 2284.400 MB/sec [ 0.479958] 32regs : 2324.000 MB/sec [ 0.479961] xor: using function: arm4regs (3314.800 MB/sec) [ 0.479965] pinctrl core: initialized pinctrl subsystem [ 0.480177] regulator-dummy: no parameters [ 0.480297] NET: Registered protocol family 16 [ 0.480732] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.482359] irq: Cannot allocate irq_descs @ IRQ195, assuming pre-allocated [ 0.482628] irq: Cannot allocate irq_descs @ IRQ227, assuming pre-allocated [ 0.484717] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.484721] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.490339] bio: create slab <bio-0> at 0 [ 0.660024] raid6: int32x1 gen() 279 MB/s [ 0.830005] raid6: int32x1 xor() 229 MB/s [ 0.999936] raid6: int32x2 gen() 384 MB/s [ 1.169940] raid6: int32x2 xor() 260 MB/s [ 1.339821] raid6: int32x4 gen() 384 MB/s [ 1.509825] raid6: int32x4 xor() 276 MB/s [ 1.679811] raid6: int32x8 gen() 425 MB/s [ 1.849775] raid6: int32x8 xor() 272 MB/s [ 1.849777] raid6: using algorithm int32x8 gen() (425 MB/s) [ 1.849779] raid6: .... xor() 272 MB/s, rmw enabled [ 1.849781] raid6: using intx1 recovery algorithm [ 1.849916] mvebu-pcie pcie-controller.3: PCIe1.0: link up [ 1.850006] mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 [ 1.850013] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.850018] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.850022] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.850129] PCI: bus0: Fast back to back transfers disabled [ 1.850135] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.850380] PCI: bus1: Fast back to back transfers disabled [ 1.850411] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff] [ 1.850415] pci 0000:00:02.0: BAR 7: assigned [io 0x10000-0x10fff] [ 1.850421] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref] [ 1.850425] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0010000-0xe00107ff] [ 1.850430] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1001f] [ 1.850435] pci 0000:01:00.0: BAR 0: assigned [io 0x10020-0x10027] [ 1.850439] pci 0000:01:00.0: BAR 2: assigned [io 0x10028-0x1002f] [ 1.850444] pci 0000:01:00.0: BAR 1: assigned [io 0x10030-0x10033] [ 1.850448] pci 0000:01:00.0: BAR 3: assigned [io 0x10034-0x10037] [ 1.850453] pci 0000:00:02.0: PCI bridge to [bus 01] [ 1.850457] pci 0000:00:02.0: bridge window [io 0x10000-0x10fff] [ 1.850467] pci 0000:00:02.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.850474] PCI: enabling device 0000:00:02.0 (0140 -> 0143) [ 1.850883] SCSI subsystem initialized [ 1.851741] Switching to clocksource armada_370_xp_clocksource [ 1.851890] AppArmor: AppArmor Filesystem Enabled [ 1.852727] NET: Registered protocol family 2 [ 1.852983] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 1.853039] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 1.853091] TCP: Hash tables configured (established 8192 bind 8192) [ 1.853122] TCP: reno registered [ 1.853128] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 1.853143] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 1.853226] NET: Registered protocol family 1 [ 1.853350] RPC: Registered named UNIX socket transport module. [ 1.853354] RPC: Registered udp transport module. [ 1.853356] RPC: Registered tcp transport module. [ 1.853358] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.853376] pci 0000:01:00.0: Apply mv9235 specific programming steps [ 1.853470] Trying to unpack rootfs image as initramfs... [ 2.755942] Freeing initrd memory: 3540K (83001000 - 83376000) [ 2.756127] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 2.757277] Initialise module verification [ 2.757304] audit: initializing netlink socket (disabled) [ 2.757336] type=2000 audit(2.750:1): initialized [ 2.758285] VFS: Disk quotas dquot_6.5.2 [ 2.758329] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.758553] NFS: Registering the id_resolver key type [ 2.758569] Key type id_resolver registered [ 2.758572] Key type id_legacy registered [ 2.758588] msgmni has been set to 2012 [ 2.759028] async_tx: api initialized (async) [ 2.759033] Key type asymmetric registered [ 2.759036] Asymmetric key parser 'x509' registered [ 2.759180] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 2.759185] io scheduler noop registered [ 2.759197] io scheduler cfq registered (default) [ 2.759855] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 2.760253] mv_xor f1060800.xor: Marvell shared XOR driver [ 2.792077] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq ) [ 2.821998] mv_xor f1060800.xor: freeing 1 in use descriptors! [ 2.822006] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( intr crc32c ) [ 2.822861] mv_xor f1060900.xor: Marvell shared XOR driver [ 2.861983] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq ) [ 2.892022] mv_xor f1060900.xor: freeing 1 in use descriptors! [ 2.892030] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( intr crc32c ) [ 2.893263] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.914786] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A [ 3.795689] console [ttyS0] enabled [ 3.819607] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 45) is a 16550A [ 3.833972] brd: module loaded [ 3.837041] Loading iSCSI transport class v2.0-870. [ 3.843573] Change defer qc mode on external port for compatibility [ 3.849864] Change defer qc mode on external port for compatibility [ 3.856167] Change defer qc mode on external port for compatibility [ 3.862468] Change defer qc mode on external port for compatibility [ 3.881861] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode [ 3.889986] ahci 0000:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.901017] scsi0 : ahci [ 3.904018] scsi1 : ahci [ 3.906901] scsi2 : ahci [ 3.909849] scsi3 : ahci [ 3.912759] ata1: SATA max UDMA/133 abar m2048@0xe0010000 port 0xe0010100 irq 65 [ 3.920187] ata2: SATA max UDMA/133 abar m2048@0xe0010000 port 0xe0010180 irq 65 [ 3.927624] ata3: SATA max UDMA/133 abar m2048@0xe0010000 port 0xe0010200 irq 65 [ 3.935066] ata4: SATA max UDMA/133 abar m2048@0xe0010000 port 0xe0010280 irq 65 [ 4.291769] ata1: SATA link down (SStatus 0 SControl 300) [ 4.297190] ata1: No present pin info for SATA link down event [ 4.651767] ata2: SATA link down (SStatus 0 SControl 300) [ 4.657186] ata2: Disk is not present for SATA link down event [ 5.011770] ata3: SATA link down (SStatus 0 SControl 300) [ 5.017190] ata3: Disk is not present for SATA link down event [ 5.371767] ata4: SATA link down (SStatus 0 SControl 300) [ 5.377186] ata4: Disk is not present for SATA link down event [ 5.383496] ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 5.392330] ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 5.402251] scsi4 : ahci_mv_platform [ 5.406255] scsi5 : ahci_mv_platform [ 5.410196] ata5: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 [ 5.418156] ata6: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 [ 5.771764] ata5: SATA link down (SStatus 0 SControl 300) [ 5.777184] ata5: Disk is not present for SATA link down event [ 6.131763] ata6: SATA link down (SStatus 0 SControl 300) [ 6.137182] ata6: No present pin info for SATA link down event [ 6.145393] m25p80 spi0.0: n25q064 (8192 Kbytes) [ 6.150039] Searching for RedBoot partition table in spi0.0 at offset 0x7f0000 [ 6.253217] 6 RedBoot partitions found on MTD device spi0.0 [ 6.258811] Creating 6 MTD partitions on "spi0.0": [ 6.263648] 0x000000000000-0x0000000f0000 : "RedBoot" [ 6.269583] 0x0000000f0000-0x0000003c0000 : "zImage" [ 6.275424] 0x0000003c0000-0x0000007d0000 : "rd.gz" [ 6.281114] 0x0000007d0000-0x0000007e0000 : "vendor" [ 6.286487] vender Mac0 address : 00:11:32:88:5d:cb [ 6.291386] vender Mac1 address : 00:11:32:88:5d:cc [ 6.296293] vender Mac2 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 6.302151] vender Mac3 doesn't set ucSum:0x00 Buf:0x00 Sum:0. [ 6.308006] serial number='1810NWN991200' [ 6.312633] 0x0000007e0000-0x0000007f0000 : "RedBoot Config" [ 6.319424] 0x0000007f0000-0x000000800000 : "FIS directory" [ 6.328262] SoC: model = 0x6820, revision = 0x4 [ 6.332884] mvPncVirtBase = 0xc0c00000, pncTcamSize = 1024 [ 6.338390] o 3 Giga ports supported [ 6.342158] o SKB recycle supported for SWF (Disabled) [ 6.347490] o NETA acceleration mode 4 [ 6.351425] o BM supported for CPU: 4 BM pools [ 6.356062] o PnC supported (Enabled) [ 6.359910] o RX Queue support: 8 Queues * 512 Descriptors [ 6.365592] o TX Queue support: 8 Queues * 1024 Descriptors [ 6.371359] o GSO supported [ 6.374338] o GRO supported [ 6.377314] o Receive checksum offload supported [ 6.382123] o Transmit checksum offload supported [ 6.387017] o Driver ERROR statistics enabled [ 6.391562] o Driver INFO statistics enabled [ 6.396022] o Driver DEBUG statistics enabled [ 6.400567] [ 6.402935] port #0: is_sgmii=1, is_rgmii=0, phy_addr=1 [ 6.408205] o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 [ 6.416524] [ 6.418019] o Port 0 is connected to Linux netdevice [ 6.426646] o eth0, ifindex = 2, GbE port = 0 [ 6.431383] o eth0, phy chipid = 1410dd0, Support WOL = 32 [ 6.440661] giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform) [ 6.446799] [ 6.448373] port #2: is_sgmii=1, is_rgmii=0, phy_addr=0 [ 6.453626] o Loading network interface(s) for port #2: cpu_mask=0x3, tx_csum_limit=2048 [ 6.461936] [ 6.463430] o Port 2 is connected to Linux netdevice [ 6.472007] o eth1, ifindex = 3, GbE port = 2 [ 6.476743] o eth1, phy chipid = 1410dd0, Support WOL = 32 [ 6.486023] giga p=2: mtu=1500, mac=00:50:43:02:02:03 (platform) [ 6.492148] [ 6.494055] libphy: orion_mdio_bus: probed [ 6.502191] mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 6.571904] i2c /dev entries driver [ 7.375560] Syno_HddMon: Initialization completed. [ 7.390436] armada_thermal f10e4078.thermal: Overheat threshold between 92..107 [ 7.398263] md: linear personality registered for level -1 [ 7.403785] md: raid0 personality registered for level 0 [ 7.409118] md: raid1 personality registered for level 1 [ 7.414457] md: raid10 personality registered for level 10 [ 7.420129] md: raid6 personality registered for level 6 [ 7.425471] md: raid5 personality registered for level 5 [ 7.430803] md: raid4 personality registered for level 4 [ 7.436315] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-devel@redhat.com [ 7.444798] cpuidle: using governor ladder [ 7.449116] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 [ 7.458473] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) [ 7.466935] mvCesaInit: channels=2, session=640, queue=256 [ 7.480565] armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode [ 7.489902] cesadev_init(80616ae0) [ 7.493904] TCP: cubic registered [ 7.497234] NET: Registered protocol family 17 [ 7.501736] Key type dns_resolver registered [ 7.506093] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 7.513814] Registering suspend init for this board failed [ 7.521420] Loading module verification blacklist certificates [ 7.527306] Loading module verification certificates [ 7.532343] MODSIGN: Loaded cert 'Synology SDG kernel module signing key: 7bd0b0d6bcd31651c22ce3978bdc8c8bdc417329' [ 7.546511] MODSIGN: Loaded cert 'Synology Root Certification Authority: f2c075361f168425f8b5ef31b796406c3aab2089' [ 7.556931] MODSIGN: Loaded cert 'Synology Kernel Module Signing Certification Authority: 600839b5d127e0e11d817a31f0575d323a7c0e28' [ 7.568834] MODSIGN: Loaded cert 'Synology kernel module signing key: 4646ce54489669338118a3b1286da156ac366fa5' [ 7.578976] registered taskstats version 1 [ 7.583137] regulator-dummy: disabling [ 7.587139] Freeing unused kernel memory: 228K (805f8000 - 80631000) START /linuxrc.syno Insert basic USB modules... :: Loading module usb-common ... [ OK ] :: Loading module usbcore[ 7.699412] usbcore: registered new interface driver usbfs [ 7.706715] usbcore: registered new interface driver hub [ 7.715270] usbcore: registered new device driver usb ... [ OK ] :: Loading module ehci-hcd[ 7.744541] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ... [ OK ] :: Loading module xhci-hcd[ 7.777788] xhci-hcd f10f0000.usb3: USB2 Vbus gpio 58 [ 7.782904] xhci-hcd f10f0000.usb3: power control enabled [ 7.788327] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 7.793677] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 1 [ 7.801356] xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 [ 7.807913] hub 1-0:1.0: USB hub found [ 7.811690] hub 1-0:1.0: 1 port detected [ 7.815755] xhci-hcd f10f0000.usb3: USB3 Vbus gpio 58 [ 7.820833] xhci-hcd f10f0000.usb3: power control enabled [ 7.826281] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 7.831628] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 7.841361] hub 2-0:1.0: USB hub found [ 7.845178] hub 2-0:1.0: 1 port detected [ 7.849262] xhci-hcd f10f8000.usb3: USB2 Vbus gpio 59 [ 7.854356] xhci-hcd f10f8000.usb3: power control enabled [ 7.859782] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 7.865144] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3 [ 7.872835] xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 [ 7.879134] hub 3-0:1.0: USB hub found [ 7.882929] hub 3-0:1.0: 1 port detected [ 7.886965] xhci-hcd f10f8000.usb3: USB3 Vbus gpio 59 [ 7.892051] xhci-hcd f10f8000.usb3: power control enabled [ 7.897480] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 7.902858] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 7.911103] hub 4-0:1.0: USB hub found [ 7.914921] hub 4-0:1.0: 1 port detected ... [ OK ] :: Loading module ehci-orion[ 7.959771] ehci-orion: EHCI orion driver [ 7.963911] orion-ehci f1058000.usb: failed to get Vbus gpio [ 7.969597] orion-ehci f1058000.usb: USB2 Vbus gpio -1 [ 7.974774] orion-ehci f1058000.usb: power control disabled [ 7.980368] orion-ehci f1058000.usb: EHCI Host Controller [ 7.985806] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 5 [ 7.993452] orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 [ 8.011786] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 8.018262] hub 5-0:1.0: USB hub found [ 8.022061] hub 5-0:1.0: 1 port detected ... [ OK ] insmod: can't insert '/lib/modules/etxhci-hcd.ko': No such file or directory Insert net driver([ 8.064489] rs816_synobios: module license 'Synology Inc.' taints kernel. Mindspeed only).[ 8.072668] Disabling lock debugging due to kernel taint .. [ 8.079916] Synobios RS816 GPIO initialized [ 8.084325] 2019-1-17 17:28:27 UTC [ 8.087743] synobios: load, major number 201 [ 8.092049] Brand: Synology [ 8.094872] Model: RS-816 [ 8.097509] This is default settings: set group disks wakeup number to 1, spinup time deno 1 [ 8.106004] synobios cpu_arch proc entry initialized [ 8.110987] synobios crypto_hw proc entry initialized [ 8.116064] synobios syno_platform proc entry initialized [ 8.121547] synobios open /dev/ttyS1 success Starting /usr/syno/bin/synocfgen... /usr/syno/bin/synocfgen returns 0 [ 8.136681] synobios: unload Exit on error [1] DISK NOT INSTALLED... Thr Jan 17 17:28:27 UTC 2019 none /sys/kernel/debug debugfs rw,relatime 0 0 sys /sys sysfs rw,relatime 0 0 none /dev devtmpfs rw,relatime,size=513436k,nr_inodes=128359,mode=755 0 0 proc /proc proc rw,relatime 0 0 linuxrc.syno failed on 1 starting pid 901, tty '': '/etc/rc' :: Starting /etc/rc :: Mounting procfs ... [ OK ] :: Mounting tmpfs ... [ OK ] :: Mounting devtmpfs ... [ OK ] :: Mounting devpts ... [ OK ] :: Mounting sysfs ... [ OK ] mdadm: error opening /dev/md1: No such file or directory rc: Use all internal disk as swap. rc: No internal disk installed. swapon: can't stat '/dev/md1': No such file or directory :: Loading module fat ... [ OK ] :: Loading module vfat ... [ OK ] :: Loading module synobios[ 8.612394] Synobios RS816 GPIO initialized [ 8.616787] 2019-1-17 17:28:27 UTC [ 8.620206] synobios: load, major number 201 [ 8.624516] Brand: Synology [ 8.627338] Model: RS-816 [ 8.629975] This is default settings: set group disks wakeup number to 1, spinup time deno 1 [ 8.638470] synobios cpu_arch proc entry initialized [ 8.643458] synobios crypto_hw proc entry initialized [ 8.648529] synobios syno_platform proc entry initialized [ 8.654009] synobios open /dev/ttyS1 success ... [ OK ] [ 8.785794] eth0: mac address changed [ 8.804356] eth1: mac address changed [ 8.827955] pool #0: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added [ 8.835429] eth0: link up [ 8.838109] eth0: started udhcpc (v1.16.1) started [ 9.171770] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 9.916198] pool #2: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added [ 9.923706] eth1: started udhcpc (v1.16.1) started eth0 Link encap:Ethernet HWaddr 00:11:32:88:5D:CB inet addr:172.16.10.22 Bcast:172.16.10.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1024 RX bytes:746 (746.0 B) TX bytes:1480 (1.4 KiB) Interrupt:193 eth1 Link encap:Ethernet HWaddr 00:11:32:88:5D:CC UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1024 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:194 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) :: Starting syslogd ... [ OK ] /etc/rc: line 262: /usr/syno/bin/syno_pstore_collect: not found :: Starting scemd :: Starting services in background Starting findhostd in flash_rd... Starting services in flash_rd... Running /usr/syno/etc/rc.d/J01httpd.sh... Starting httpd:80 in flash_rd... Starting httpd:5000 in flash_rd... Running /usr/syno/etc/rc.d/J03ssdpd.sh... /usr/bin/minissdpd -i eth0 -i eth1 (15): upnp:rootdevice (51): uuid:upnp_SynologyNAS-001132885dcb::upnp:rootdevice (56): Synology/synology_armada38x_rs816/6.2-23824/172.16.10.22 (45): http://172.16.10.22:5000/description-eth0.xml Connected. done. /usr/syno/bin/reg_ssdp_service 172.16.10.22 001132885dcb 6.2-23824 synology_armada38x_rs816 eth0 eth1 not RUNNING Running /usr/syno/etc/rc.d/J04synoagentregisterd.sh... Starting synoagentregisterd... Running /usr/syno/etc/rc.d/J30DisableNCQ.sh... cat: can't open '/sys/block/sd*/device//model': No such file or directory Running /usr/syno/etc/rc.d/J80ADTFanControl.sh... Running /usr/syno/etc/rc.d/J98nbnsd.sh... Starting nbnsd... Running /usr/syno/etc/rc.d/J99avahi.sh... Starting Avahi mDNS/DNS-SD Daemon cname_load_conf failed:/var/tmp/nginx/avahi-aliases.conf :: Loading module usb-storage[ 18.276890] usb-storage 1-1:1.0: USB Mass Storage device detected [ 18.283353] scsi6 : usb-storage 1-1:1.0 [ 18.288891] usbcore: registered new interface driver usb-storage ... [ OK ] ============ Date ============ Thr Jan 17 17:2[ 19.431781] usb 1-1: reset high-speed USB device number 2 using xhci-hcd [ 19.451914] xhci-hcd f10f0000.usb3: xHCI xhci_drop_endpoint called with disabled ep bc532a40 [ 19.460392] xhci-hcd f10f0000.usb3: xHCI xhci_drop_endpoint called with disabled ep bc532a6c Thu Jan 17 17:28:37 2019 RackStation login: [ 19.482015] scsi 6:0:0:0: Direct-Access Dev PQ: 0 ANSI: 0 CCS [ 19.493314] sd 6:0:0:0: [sdq] 63062016 512-byte logical blocks: (32.2 GB/30.0 GiB) [ 19.501933] sd 6:0:0:0: [sdq] Write Protect is off [ 19.507698] sd 6:0:0:0: [sdq] Asking for cache data failed [ 19.513252] sd 6:0:0:0: [sdq] Assuming drive cache: write through [ 19.520408] sd 6:0:0:0: [sdq] Asking for cache data failed [ 19.525941] sd 6:0:0:0: [sdq] Assuming drive cache: write through [ 19.532459] sdq: sdq1 [ 19.535962] sd 6:0:0:0: [sdq] Asking for cache data failed [ 19.541477] sd 6:0:0:0: [sdq] Assuming drive cache: write through [ 19.547644] sd 6:0:0:0: [sdq] Attached SCSI disk RackStation login:
Re: Debian on Synology RS816 (Armada 385) January 17, 2019 11:56AM |
Registered: 5 years ago Posts: 41 |
sudo parted --script /dev/sdX \ mklabel msdos \ mkpart primary ext3 1MiB 100% sudo mkfs.ext3 -L rootfs /dev/sdX1 ROOTFSDIR=$(mktemp -d) sudo mount /dev/sdX1 $ROOTFSDIR sudo tar -C $ROOTFSDIR -jxvf Debian-4.12.4-mvebu-tld-1-rootfs-bodhi.tar.bz2 cp -a zImage-4.12.4-mvebu-tld-1 zImage