Problems with Pogoplug E02

Hi,

First: sorry for my english :-)

I have 3 identical Pogoplugs E02 buy in December.

One i have installing Debian with the script of December, all fine.

Yesterday i want isntall the other 2, all ok boot no boot.

Led ist ornage but no network connection. I take the image of the 1, but no running too.

I see that there are changes in the script, perhaps a new bootlader?

Can i backup the bootlader partition from my first running pogo und flash the other 2?
How?

Thx for your help

U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt

** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1435408 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
4529711 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-2.6.32-5-kirkwood
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1435344 Bytes = 1.4 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-2.6.32-5-kirkwood
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4529647 Bytes = 4.3 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

After this Pogo started 2. Time and then no Output


Thats my Output from the netconsole



Edited 1 time(s). Last edit at 02/27/2013 11:49AM by bernd99.

Ok i take it like in this Thread and Debian boots :-)

http://forum.doozan.com/read.php?2,11396