Problem with 2017.07 U-Boot for SheevaPlug December 03, 2017 01:31AM |
Registered: 9 years ago Posts: 442 |
Sheevaplug> load usb 0:1 $load_uimage_addr /boot/uImage Unknown command 'load' - try 'help' Sheevaplug> help ? - alias for 'help' base - print or set address offset bdinfo - print Board Info structure boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootefi - Boots an EFI payload from memory bootelf - Boot from an ELF image in memory bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol bootvx - Boot vxWorks from an ELF image bootz - boot Linux zImage image from memory chpart - change active partition cmp - memory compare coninfo - print console devices and information cp - memory copy crc32 - checksum calculation date - get/set/reset date & time dhcp - boot image via network using DHCP/TFTP protocol diskboot- boot from IDE device dns - lookup the IP of a hostname echo - echo args to console editenv - edit environment variable env - environment handling commands exit - exit script ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) ext4load- load binary file from a Ext4 filesystem ext4ls - list files in a directory (default /) ext4size- determine a file's size false - do nothing, unsuccessfully fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fatsize - determine a file's size fdt - flattened device tree utility commands fsinfo - print information about jffs filesystems fsload - load binary file from a jffs filesystem image fsls - list jffs files in a directory (default /) go - start application at address 'addr' gpio - query and control gpio pins gpt - GUID Partition Table help - print command description/usage ide - IDE sub-system iminfo - print header information for application image imxtract- extract a part of a multi-image itest - return true/false on integer compare loadb - load binary file over serial line (kermit mode) loads - load S-Record file over serial line loadx - load binary file over serial line (xmodem mode) loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range md - memory display mii - MII utility commands mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - display MMC info mtdparts- define flash/nand partitions mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nfs - boot image via network using NFS protocol nm - memory modify (constant address) ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables reset - Perform RESET of the CPU run - run commands in an environment variable saveenv - save environment variables to persistent storage setenv - set environment variables setexpr - set environment variable as the result of eval expression showvar - print local hushshell variables sleep - delay execution for some time sntp - synchronize RTC via network source - run script from memory test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol true - do nothing, successfully ubi - ubi commands ubifsload- load file from an UBIFS filesystem ubifsls - list files in a directory ubifsmount- mount UBIFS volume ubifsumount- unmount UBIFS volume usb - USB sub-system usbboot - boot from USB device version - print monitor, compiler and linker version
Re: Problem with 2017.07 U-Boot for SheevaPlug December 03, 2017 02:47PM |
Admin Registered: 13 years ago Posts: 18,580 |
ver helpThen post the entire serial console log up to this point.
Re: Problem with 2017.07 U-Boot for SheevaPlug December 03, 2017 08:13PM |
Registered: 9 years ago Posts: 442 |
> ver > help >> Then post the entire serial console log up to this
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:58:14 -0700) Marvell-Sheevaplug SoC: Kirkwood 88F6281_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 512 MiB MMC: MVEBU_MMC: 0 In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 Sheevaplug> ver U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:58:14 -0700) Marvell-Sheevaplug gcc (Debian 6.3.0-18) 6.3.0 20170516 GNU ld (GNU Binutils for Debian) 2.28 Sheevaplug> help ? - alias for 'help' base - print or set address offset bdinfo - print Board Info structure boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootefi - Boots an EFI payload from memory bootelf - Boot from an ELF image in memory bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol bootvx - Boot vxWorks from an ELF image bootz - boot Linux zImage image from memory chpart - change active partition cmp - memory compare coninfo - print console devices and information cp - memory copy crc32 - checksum calculation date - get/set/reset date & time dhcp - boot image via network using DHCP/TFTP protocol diskboot- boot from IDE device dns - lookup the IP of a hostname echo - echo args to console editenv - edit environment variable env - environment handling commands exit - exit script ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) ext4load- load binary file from a Ext4 filesystem ext4ls - list files in a directory (default /) ext4size- determine a file's size false - do nothing, unsuccessfully fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fatsize - determine a file's size fdt - flattened device tree utility commands fsinfo - print information about jffs filesystems fsload - load binary file from a jffs filesystem image fsls - list jffs files in a directory (default /) go - start application at address 'addr' gpio - query and control gpio pins gpt - GUID Partition Table help - print command description/usage ide - IDE sub-system iminfo - print header information for application image imxtract- extract a part of a multi-image itest - return true/false on integer compare loadb - load binary file over serial line (kermit mode) loads - load S-Record file over serial line loadx - load binary file over serial line (xmodem mode) loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range md - memory display mii - MII utility commands mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - display MMC info mtdparts- define flash/nand partitions mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nfs - boot image via network using NFS protocol nm - memory modify (constant address) ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables reset - Perform RESET of the CPU run - run commands in an environment variable saveenv - save environment variables to persistent storage setenv - set environment variables setexpr - set environment variable as the result of eval expression showvar - print local hushshell variables sleep - delay execution for some time sntp - synchronize RTC via network source - run script from memory test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol true - do nothing, successfully ubi - ubi commands ubifsload- load file from an UBIFS filesystem ubifsls - list files in a directory ubifsmount- mount UBIFS volume ubifsumount- unmount UBIFS volume usb - USB sub-system usbboot - boot from USB device version - print monitor, compiler and linker version Sheevaplug>
Re: Problem with 2017.07 U-Boot for SheevaPlug December 04, 2017 04:24AM |
Admin Registered: 13 years ago Posts: 18,580 |
Re: Problem with 2017.07 U-Boot for SheevaPlug December 05, 2017 04:44PM |
Admin Registered: 13 years ago Posts: 18,580 |
Quote
bodhi
> Please test this version (attached).
>
> You can kwboot it, change the u-boot envs back to
> use "load", and then boot.
Re: Problem with 2017.07 U-Boot for SheevaPlug December 06, 2017 12:42AM |
Registered: 9 years ago Posts: 442 |
U-Boot 2017.07-tld-2 (Dec 04 2017 - 02:00:45 -0800) Marvell-Sheevaplug SoC: Kirkwood 88F6281_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 512 MiB MMC: MVEBU_MMC: 0 In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 Sheevaplug> help ? - alias for 'help' base - print or set address offset bdinfo - print Board Info structure boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootefi - Boots an EFI payload from memory bootelf - Boot from an ELF image in memory bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol bootvx - Boot vxWorks from an ELF image bootz - boot Linux zImage image from memory chpart - change active partition cmp - memory compare coninfo - print console devices and information cp - memory copy crc32 - checksum calculation date - get/set/reset date & time dhcp - boot image via network using DHCP/TFTP protocol diskboot- boot from IDE device dns - lookup the IP of a hostname echo - echo args to console editenv - edit environment variable env - environment handling commands exit - exit script ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) ext4load- load binary file from a Ext4 filesystem ext4ls - list files in a directory (default /) ext4size- determine a file's size false - do nothing, unsuccessfully fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fatsize - determine a file's size fdt - flattened device tree utility commands fsinfo - print information about jffs filesystems fsload - load binary file from a jffs filesystem image fsls - list jffs files in a directory (default /) fstype - Look up a filesystem type go - start application at address 'addr' gpio - query and control gpio pins gpt - GUID Partition Table help - print command description/usage ide - IDE sub-system iminfo - print header information for application image imxtract- extract a part of a multi-image itest - return true/false on integer compare load - load binary file from a filesystem loadb - load binary file over serial line (kermit mode) loads - load S-Record file over serial line loadx - load binary file over serial line (xmodem mode) loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range ls - list files in a directory (default /) md - memory display mii - MII utility commands mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - display MMC info mtdparts- define flash/nand partitions mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nfs - boot image via network using NFS protocol nm - memory modify (constant address) ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables reset - Perform RESET of the CPU run - run commands in an environment variable save - save file to a filesystem saveenv - save environment variables to persistent storage setenv - set environment variables setexpr - set environment variable as the result of eval expression showvar - print local hushshell variables size - determine a file's size sleep - delay execution for some time sntp - synchronize RTC via network source - run script from memory test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol true - do nothing, successfully ubi - ubi commands ubifsload- load file from an UBIFS filesystem ubifsls - list files in a directory ubifsmount- mount UBIFS volume ubifsumount- unmount UBIFS volume usb - USB sub-system usbboot - boot from USB device version - print monitor, compiler and linker version Sheevaplug>
Sheevaplug> load $bootdev $device $load_dtb_addr $dtb_file 10506 bytes read in 35 ms (293 KiB/s)
Re: Problem with 2017.07 U-Boot for SheevaPlug December 06, 2017 02:24AM |
Admin Registered: 13 years ago Posts: 18,580 |
> Sheevaplug> load $bootdev $device $load_dtb_addr > $dtb_file > 10506 bytes read in 35 ms (293 KiB/s) >>
Re: Problem with 2017.07 U-Boot for SheevaPlug December 06, 2017 04:45PM |
Admin Registered: 13 years ago Posts: 18,580 |
Re: Problem with 2017.07 U-Boot for SheevaPlug December 07, 2017 05:54AM |
Registered: 6 years ago Posts: 337 |
Re: Problem with 2017.07 U-Boot for SheevaPlug December 07, 2017 07:56PM |
Registered: 9 years ago Posts: 442 |
Re: Problem with 2017.07 U-Boot for SheevaPlug December 08, 2017 02:28AM |
Admin Registered: 13 years ago Posts: 18,580 |
Re: Problem with 2017.07 U-Boot for SheevaPlug December 08, 2017 02:34AM |
Admin Registered: 13 years ago Posts: 18,580 |
Re: Problem with 2017.07 U-Boot for SheevaPlug December 08, 2017 02:48AM |
Registered: 6 years ago Posts: 337 |
Re: Problem with 2017.07 U-Boot for SheevaPlug December 08, 2017 02:49AM |
Admin Registered: 13 years ago Posts: 18,580 |
Re: Problem with 2017.07 U-Boot for SheevaPlug December 09, 2017 05:36AM |
Registered: 6 years ago Posts: 337 |
Connect the BusPirate and the Serial Adapter to the Dockstar's JTAG header
Re: Problem with 2017.07 U-Boot for SheevaPlug December 09, 2017 04:50PM |
Admin Registered: 13 years ago Posts: 18,580 |
Re: Problem with 2017.07 U-Boot for SheevaPlug December 10, 2017 05:23AM |
Registered: 6 years ago Posts: 337 |