Re: Who can compile an u-boot bin for me? January 29, 2016 09:18AM |
Admin Registered: 13 years ago Posts: 18,900 |
Re: Iomega ix4-200d U-boot needed February 02, 2016 02:07AM |
Registered: 8 years ago Posts: 49 |
root@debian:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x4000 root@debian:/tools# ./flash_erase /dev/mtd0 0 32 Erase Total 32 Units Performing Flash Erase of length 16384 at offset 0x7c000 done root@debian:/tools# ./nandwrite /dev/mtd0 uboot.2015.10-tld-1.sheevaplug.mtd0.kwb Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x4000 Writing data to block 2 at offset 0x8000 Writing data to block 3 at offset 0xc000 Writing data to block 4 at offset 0x10000 Writing data to block 5 at offset 0x14000 Writing data to block 6 at offset 0x18000 Writing data to block 7 at offset 0x1c000 Writing data to block 8 at offset 0x20000 Writing data to block 9 at offset 0x24000 Writing data to block 10 at offset 0x28000 Writing data to block 11 at offset 0x2c000 Writing data to block 12 at offset 0x30000 Writing data to block 13 at offset 0x34000 Writing data to block 14 at offset 0x38000 Writing data to block 15 at offset 0x3c000 Writing data to block 16 at offset 0x40000 Writing data to block 17 at offset 0x44000 Writing data to block 18 at offset 0x48000 Writing data to block 19 at offset 0x4c000 Writing data to block 20 at offset 0x50000 Writing data to block 21 at offset 0x54000 Writing data to block 22 at offset 0x58000 Writing data to block 23 at offset 0x5c000 Writing data to block 24 at offset 0x60000 Writing data to block 25 at offset 0x64000 Writing data to block 26 at offset 0x68000 Writing data to block 27 at offset 0x6c000 Writing data to block 28 at offset 0x70000 Writing data to block 29 at offset 0x74000 Writing data to block 30 at offset 0x78000 Writing data to block 31 at offset 0x7c000 root@debian:/tools# ./flash_erase /dev/mtd0 0xc0000 8Erase Total 8 Units Performing Flash Erase of length 16384 at offset 0xdc000 done root@debian:/tools# ./nandwrite -s 786432 /dev/mtd0 uboot.2014.07-tld-3.environment.img Writing data to block 48 at offset 0xc0000 Writing data to block 49 at offset 0xc4000 Writing data to block 50 at offset 0xc8000 Writing data to block 51 at offset 0xcc000 Writing data to block 52 at offset 0xd0000 Writing data to block 53 at offset 0xd4000 Writing data to block 54 at offset 0xd8000 Writing data to block 55 at offset 0xdc000 root@debian:/tools# fw_printenv Too few good blocks within range
Re: Iomega ix4-200d U-boot needed February 02, 2016 03:02AM |
Admin Registered: 13 years ago Posts: 18,900 |
Re: Iomega ix4-200d U-boot needed February 02, 2016 06:58AM |
Registered: 8 years ago Posts: 49 |
Re: Iomega ix4-200d U-boot needed February 02, 2016 12:44PM |
Admin Registered: 13 years ago Posts: 18,900 |
Re: Who can compile an u-boot bin for me? February 03, 2016 11:42PM |
Registered: 8 years ago Posts: 49 |
Re: Who can compile an u-boot bin for me? February 03, 2016 11:54PM |
Admin Registered: 13 years ago Posts: 18,900 |
Re: Iomega ix4-200d U-boot needed February 03, 2016 11:58PM |
Registered: 8 years ago Posts: 49 |
Re: Iomega ix4-200d U-boot needed February 04, 2016 12:22AM |
Admin Registered: 13 years ago Posts: 18,900 |
./kwboot -t -B 115200 /dev/ttyUSB0 -b mtd0.bin -p
printenv
Re: Iomega ix4-200d U-boot needed February 04, 2016 01:17AM |
Registered: 8 years ago Posts: 49 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** uboot_ver:v1.1.1 ** ** MARVELL BOARD: IX4-110 LE U-Boot 1.1.4 (Mar 10 2011 - 15:01:57) Marvell version: 3.4.18 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CF600 Soc: 88F6281 A1 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Found 0x20 i2c device Toggle power status Set Power State as Always On Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:32 MB Found ADT7473, program LED ...(led_volt=90) OK Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp_min=60) OK Marvell Serial ATA Adapter Integrated Sata device found CPU : Marvell Feroceon (Rev 1) Could not found correct initrd Streaming disabled Write allocate disabled Module 0 is RGMII Module 1 is RGMII USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 SCSI: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode flags: 64bit ncq stag led pmp slum part scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: WDC WD20EFRX-68A Rev: 80.0 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 Marvell>> printenv bootdelay=1 baudrate=115200 loads_echo=0 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 run_diag=yes CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage console=console=ttyS0,115200 mtdparts=nand_mtd:0xa0000@0x0(uboot),0x00010000@0x000a0000(param),32m@0x0(flash) uboot_start=0x0 uboot_size=0xa0000 env_start=0xa0000 env_size=0x10000 kernel_start=0xb0000 kernel_size=0x228000 initrd_start=0x2d8000 initrd_size=0x300000 make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=nand_mtd:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash); flash_load=run make_boot_args;nand read.e 0x2000000 $(kernel_start) $(kernel_size);nand read.e 0x12000000 $(initrd_start) $(initrd_size);bootm 0x2000000 0x12000000; bootcmd=run flash_load; standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x2000000; ethaddr=00:50:43:f6:15:30 ethmtu=1500 mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no uboot_ver=v1.1.1 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no disaMvPnp=no eth1addr=00:50:43:f6:15:31 enaAutoRecovery=yes pcieTune=no ethact=egiga0 Environment size: 1627/16380 bytes
Re: Iomega ix4-200d U-boot needed February 04, 2016 02:39AM |
Admin Registered: 13 years ago Posts: 18,900 |
help
Re: Iomega ix4-200d U-boot needed February 04, 2016 02:44AM |
Admin Registered: 13 years ago Posts: 18,900 |
Re: Iomega ix4-200d U-boot needed February 04, 2016 02:48AM |
Registered: 8 years ago Posts: 49 |
Marvell>> help ? - alias for 'help' SatR - sample at reset sub-system, relevent for DB only base - print or set address offset boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootext2 dev:boot_part1,boot_part2 addr boot_image linux_dev_name bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol bubt - Burn an image on the Boot Nand Flash. chpart - change active partition cmp - memory compare cmpm - Compare Memory cp - memory copy cpumap - Display CPU memory mapping settings. crc32 - checksum calculation date - get/set/reset date & time dclk - Display the MV device CLKs. dhcp - invoke DHCP client to obtain IP/boot params diskboot- boot from IDE device echo - echo args to console eeprom - EEPROM sub-system erase - erase FLASH memory ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fi - Find value in the memory. flinfo - print FLASH memory information fsinfo - print information about filesystems fsload - load binary file from a filesystem image g - start application at cached address 'addr'(default addr 0x40000) go - start application at address 'addr' help - print online help icrc32 - checksum calculation ide - IDE sub-system iloop - infinite loop on address range imd - i2c memory display imm[.b, .s, .w, .l] - i2c memory modify (auto-incrementing) imw - memory write (fill) inm - memory modify (constant address) iprobe - probe to discover valid I2C chip addresses ir - reading and changing MV internal register values. loop - infinite loop on address range ls - list files in a directory (default /) map - Diasplay address decode windows md - memory display me - PCI master enable mm - memory modify (auto-incrementing) mp - map PCI BAR mtdparts- define flash/nand partitions mtest - simple RAM test mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nbubt - Burn a boot loader image on the Boot Nand Flash. nm - memory modify (constant address) pci - list and access PCI Configuration Space phyRead - Read PCI-E Phy register pciePhyWrite - Write PCI-E Phy register phyRead - Read Phy register phyWrite - Write Phy register ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables protect - enable or disable FLASH write protection rarpboot- boot image via network using RARP/TFTP protocol rcvr - Satrt recovery process (Distress Beacon with TFTP server) reset - Perform RESET of the CPU resetenv - Return all environment variable to default. run - run commands in an environment variable saveenv - save environment variables to persistent storage scsi - SCSI sub-system scsiboot- boot from SCSI device se - PCI Slave enable setenv - set environment variables sflash - read, write or erase the external SPI Flash. sg - scanning the PHYs status sp - Scan PCI bus. tftpboot- boot image via network using TFTP protocol usb - USB sub-system usbboot - boot from USB device version - print monitor version
Re: Iomega ix4-200d U-boot needed February 04, 2016 03:05AM |
Admin Registered: 13 years ago Posts: 18,900 |
setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10' setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x1100000' setenv bootcmd 'run usb_make_boot_args ; run usb_boot; reset' printenv boot
Re: Iomega ix4-200d U-boot needed February 04, 2016 03:13AM |
Registered: 8 years ago Posts: 49 |
Marvell>> setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10' Marvell>> setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x1100000' Marvell>> setenv bootcmd 'run usb_make_boot_args ; run usb_boot; reset' Marvell>> printenv bootdelay=1 baudrate=115200 loads_echo=0 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 run_diag=yes CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage console=console=ttyS0,115200 mtdparts=nand_mtd:0xa0000@0x0(uboot),0x00010000@0x000a0000(param),32m@0x0(flash) uboot_start=0x0 uboot_size=0xa0000 env_start=0xa0000 env_size=0x10000 kernel_start=0xb0000 kernel_size=0x228000 initrd_start=0x2d8000 initrd_size=0x300000 make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=nand_mtd:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash); flash_load=run make_boot_args;nand read.e 0x2000000 $(kernel_start) $(kernel_size);nand read.e 0x12000000 $(initrd_start) $(initrd_size);bootm 0x2000000 0x12000000; standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x2000000; ethaddr=00:50:43:f6:15:30 ethmtu=1500 mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no uboot_ver=v1.1.1 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no disaMvPnp=no eth1addr=00:50:43:f6:15:31 enaAutoRecovery=yes pcieTune=no ethact=egiga0 usb_make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10 load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd load_uimage=ext2load usb 0:1 0x800000 /boot/uImage usb_boot=usb start; run load_uimage; run load_initrd; bootm 0x800000 0x1100000 bootcmd=run usb_make_boot_args ; run usb_boot; reset Environment size: 2105/16380 bytes Marvell>> boot (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found .... ............................................................................................................................................................................................................................................................................................................... 3156720 bytes read .... ............................ ............................................................................................................................................................................................................................................................................................................................................................................................. ........................................................................................................................................................................................................... 6325849 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.2.0-kirkwood-tld-1 Created: 2016-01-29 13:58:29 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3156656 Bytes = 3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-4.2.0-kirkwood-tld-1 Created: 2016-01-22 14:30:27 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6325785 Bytes = 6 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.2.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Aug 31 23:12:00 PDT 2015 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: Iomega ix4-200d [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0xa0000@0x0(uboot),0x10000@0xa0000(env),0x228000@0xb0000(zImage),0x300000@0x2d8000(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 504304K/524288K available (6019K kernel code, 571K rwdata, 1988K rodata, 284K init, 312K bss, 19984K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07da1b4 (8009 kB) [ 0.000000] .init : 0xc07db000 - 0xc0822000 ( 284 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b0e24 ( 572 kB) [ 0.000000] .bss : 0xc08b0e24 - 0xc08ff1a4 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000406] Console: colour dummy device 80x30 [ 0.000436] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.090098] pid_max: default: 32768 minimum: 301 [ 0.090225] Security Framework initialized [ 0.090307] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090326] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091055] Initializing cgroup subsys blkio [ 0.091083] Initializing cgroup subsys devices [ 0.091106] Initializing cgroup subsys freezer [ 0.091137] Initializing cgroup subsys net_cls [ 0.091221] CPU: Testing write buffer coherency: ok [ 0.091605] Setting up static identity map for 0x8200 - 0x8258 [ 0.091870] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.095318] devtmpfs: initialized [ 0.099591] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.100029] prandom: seed boundary self test passed [ 0.103827] prandom: 100 self tests passed [ 0.103852] pinctrl core: initialized pinctrl subsystem [ 0.105181] NET: Registered protocol family 16 [ 0.105598] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130092] cpuidle: using governor ladder [ 0.160091] cpuidle: using governor menu [ 0.160487] Feroceon L2: Enabling L2 [ 0.160531] Feroceon L2: Cache support initialised. [ 0.160899] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.161002] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 0.165946] No ATAGs? [ 0.201543] vgaarb: loaded [ 0.201919] usbcore: registered new interface driver usbfs [ 0.202001] usbcore: registered new interface driver hub [ 0.202067] usbcore: registered new device driver usb [ 0.203152] clocksource: Switched to clocksource orion_clocksource [ 0.259497] NET: Registered protocol family 2 [ 0.260133] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.260194] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.260246] TCP: Hash tables configured (established 4096 bind 4096) [ 0.260309] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.260334] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.260539] NET: Registered protocol family 1 [ 0.260928] RPC: Registered named UNIX socket transport module. [ 0.260940] RPC: Registered udp transport module. [ 0.260947] RPC: Registered tcp transport module. [ 0.260955] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.261221] Unpacking initramfs... [ 0.810400] Freeing initrd memory: 6180K (c1100000 - c1709000) [ 0.810528] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.811590] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.811621] Initialise system trusted keyring [ 0.811742] audit: initializing netlink subsys (disabled) [ 0.811789] audit: type=2000 audit(0.800:1): initialized [ 0.812420] zpool: loaded [ 0.812437] zbud: loaded [ 0.812751] VFS: Disk quotas dquot_6.6.0 [ 0.812812] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.813451] NFS: Registering the id_resolver key type [ 0.813496] Key type id_resolver registered [ 0.813505] Key type id_legacy registered [ 0.813533] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.813549] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.813777] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.814303] Key type big_key registered [ 0.836729] Key type asymmetric registered [ 0.836753] Asymmetric key parser 'x509' registered [ 0.836845] bounce: pool size: 64 pages [ 0.836916] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.836934] io scheduler noop registered [ 0.836947] io scheduler deadline registered [ 0.837003] io scheduler cfq registered (default) [ 0.838311] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.838968] irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated [ 0.839386] irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated [ 0.840217] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00 [ 0.840237] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 0.840251] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 0.840265] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.840623] PCI: bus0: Fast back to back transfers disabled [ 0.840650] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.841426] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.841473] PCI: bus1: Fast back to back transfers disabled [ 0.841640] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 0.841657] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 0.841676] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0000000-0xe00003ff] [ 0.841696] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f] [ 0.841714] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017] [ 0.841731] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f] [ 0.841750] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023] [ 0.841767] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027] [ 0.841784] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.841797] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 0.841812] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 0.842118] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.883845] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy ) [ 0.923825] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy ) [ 0.924038] mv_xor f1060900.xor: Marvell shared XOR driver [ 0.963826] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy ) [ 1.003832] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy ) [ 1.004300] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.005734] console [ttyS0] disabled [ 1.005793] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 1.766092] console [ttyS0] enabled [ 1.770831] nand: device found, Manufacturer ID: 0xec, Chip ID: 0x75 [ 1.777248] nand: Samsung NAND 32MiB 3,3V 8-bit [ 1.781803] nand: 32 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 1.789173] Scanning device for bad blocks [ 2.134603] 5 cmdlinepart partitions found on MTD device orion_nand [ 2.140900] Creating 5 MTD partitions on "orion_nand": [ 2.146091] 0x000000000000-0x0000000a0000 : "uboot" [ 2.152033] 0x0000000a0000-0x0000000b0000 : "env" [ 2.157793] 0x0000000b0000-0x0000002d8000 : "zImage" [ 2.163853] 0x0000002d8000-0x0000005d8000 : "initrd" [ 2.169910] 0x000000000000-0x000002000000 : "flash" [ 2.177335] libphy: Fixed MDIO Bus: probed [ 2.181785] libphy: orion_mdio_bus: probed [ 2.197477] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 3.283745] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:f6:15:30 [ 4.363905] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:50:43:f6:15:31 [ 4.372968] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.379596] ehci-pci: EHCI PCI platform driver [ 4.384155] ehci-orion: EHCI orion driver [ 4.388356] orion-ehci f1050000.ehci: EHCI Host Controller [ 4.393922] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 4.401788] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 4.423187] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 4.429437] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.436287] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.443560] usb usb1: Product: EHCI Host Controller [ 4.448459] usb usb1: Manufacturer: Linux 4.2.0-kirkwood-tld-1 ehci_hcd [ 4.455122] usb usb1: SerialNumber: f1050000.ehci [ 4.460533] hub 1-0:1.0: USB hub found [ 4.464384] hub 1-0:1.0: 1 port detected [ 4.469180] mousedev: PS/2 mouse device common for all mice [ 4.475470] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 4.482538] i2c /dev entries driver [ 4.487565] hidraw: raw HID events driver (C) Jiri Kosina [ 4.493396] drop_monitor: Initializing network drop monitor service [ 4.499932] NET: Registered protocol family 17 [ 4.504537] Key type dns_resolver registered [ 4.509658] Loading compiled-in X.509 certificates [ 4.514539] registered taskstats version 1 [ 4.518711] zswap: loading zswap [ 4.521961] zswap: using zbud pool [ 4.525405] zswap: using lzo compressor [ 4.540236] Key type encrypted registered [ 4.544996] rtc-mv f1010300.rtc: setting system clock to 2016-02-04 09:12:09 UTC (1454577129) [ 4.555885] Freeing unused kernel memory: 284K (c07db000 - c0822000) Loading, please wait... [ 4.634060] udevd[85]: starting version 175 [ 4.783255] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 4.901651] SCSI subsystem initialized [ 4.945186] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 4.951946] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 4.971254] usb 1-1: Product: USB2.0 Hub [ 4.984316] hub 1-1:1.0: USB hub found [ 4.991466] hub 1-1:1.0: 4 ports detected [ 5.056840] pci 0000:00:01.0: enabling device (0140 -> 0143) [ 5.062612] ahci 0000:01:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 5.101610] sata_mv f1080000.sata: slots 32 ports 2 [ 5.153288] scsi host0: sata_mv [ 5.162458] ahci 0000:01:00.0: controller can't do NCQ, turning off CAP_NCQ [ 5.176830] scsi host1: sata_mv [ 5.180335] ata1: SATA max UDMA/133 irq 33 [ 5.200521] ahci 0000:01:00.0: controller can't do PMP, turning off CAP_PMP [ 5.217140] ata2: SATA max UDMA/133 irq 33 [ 5.235753] ahci 0000:01:00.0: masking port_map 0x7 -> 0x3 [ 5.241365] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled [ 5.273265] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 5.293806] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 5.301888] ahci 0000:01:00.0: flags: 64bit stag led slum part [ 5.313321] scsi host2: ahci [ 5.317157] scsi host3: ahci [ 5.320946] scsi host4: ahci [ 5.324653] ata3: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000100 irq 84 [ 5.332084] ata4: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000180 irq 84 [ 5.339581] ata5: DUMMY [ 5.394427] usb 1-1.2: New USB device found, idVendor=125f, idProduct=de7a [ 5.401352] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 5.408733] usb 1-1.2: Product: ADATA USB Flash Drive [ 5.413823] usb 1-1.2: Manufacturer: ADATA [ 5.417939] usb 1-1.2: SerialNumber: 14B1311102300064 [ 5.450345] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 5.457088] scsi host5: usb-storage 1-1.2:1.0 [ 5.463385] usbcore: registered new interface driver usb-storage [ 5.472556] usbcore: registered new interface driver uas [ 5.563210] ata1: SATA link down (SStatus 0 SControl F300) [ 5.683200] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.689955] ata3.00: ATA-9: WDC WD20EFRX-68AX9N0, 80.00A80, max UDMA/133 [ 5.696718] ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 5.704059] ata3.00: configured for UDMA/133 [ 5.933187] ata2: SATA link down (SStatus 0 SControl F300) [ 5.953577] scsi 2:0:0:0: Direct-Access ATA WDC WD20EFRX-68A 0A80 PQ: 0 ANSI: 5 [ 6.313199] ata4: SATA link down (SStatus 0 SControl 300) [ 6.372204] sd 2:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 6.381114] sd 2:0:0:0: [sda] 4096-byte physical blocks [ 6.386754] sd 2:0:0:0: [sda] Write Protect is off [ 6.391701] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.454015] scsi 5:0:0:0: Direct-Access ADATA USB Flash Drive 1.00 PQ: 0 ANSI: 6 [ 6.462926] sda: sda1 [ 6.474340] sd 5:0:0:0: [sdb] 123480064 512-byte logical blocks: (63.2 GB/58.8 GiB) [ 6.482506] sd 2:0:0:0: [sda] Attached SCSI disk [ 6.491908] sd 5:0:0:0: [sdb] Write Protect is off [ 6.503849] sd 5:0:0:0: [sdb] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA [ 6.518008] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 6.526599] sd 5:0:0:0: Attached scsi generic sg1 type 0 [ 6.533463] sdb: sdb1 [ 6.538719] sd 5:0:0:0: [sdb] Attached SCSI removable disk Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 16.853669] EXT3-fs (sdb1): mounted filesystem with ordered data mode Begin: Running /scripts/local-bo[ 16.862132] kjournald starting. Commit interval 5 seconds ttom ... done. done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 18.004481] udevd[317]: starting version 175 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 18.790683] random: nonblocking pool is initialized [ 18.826524] orion_wdt: Initial timeout 21 sec [ 18.962670] adt7475 0-002e: ADT7473 device, revision 0 [ 19.002150] adt7475 0-002e: Optional features: fan4 pwm2 done. [ ok ] Activating swap...done. [....] Checking root file system...fsck from util-linux 2.20.1 rootfs: clean, 15997/3859072 files, 462346/15435004 blocks done. [ 20.739254] EXT3-fs (sdb1): using internal journal [ ok ] Loading kernel modules...done. [ ok ] Cleaning up temporary files... /lib/init/rw. [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.20.1 done. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [....] Configuring network interfaces...[ 25.280287] NET: Registered protocol family 10 Internet Systems Consortium DHCP Client 4.2.2 Copyright 2004-2011 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ [ 26.537586] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Listening on LPF/eth0/00:50:43:f6:15:30 Sending on LPF/eth0/00:50:43:f6:15:30 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 1 No DHCPOFFERS received. No working leases in persistent database - sleeping. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1810 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... [ ok ] Starting system message bus: dbus. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting NTP server: ntpd. [ ok ] Starting rpcbind daemon...[....] Already running.. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting OpenBSD Secure Shell server: sshd. 1811 (klogd) . ok [....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemonTimeout reached while wating for return value Could not receive return value from daemon process. (warning). Debian GNU/Linux 7 debian ttyS0 debian login: root Password: Last login: Mon Feb 1 23:36:18 PST 2016 on ttyS0 Linux debian 4.2.0-kirkwood-tld-1 #1 PREEMPT Mon Aug 31 23:12:00 PDT 2015 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~#
Re: Iomega ix4-200d U-boot needed February 04, 2016 03:32AM |
Admin Registered: 13 years ago Posts: 18,900 |
[ 2.134603] 5 cmdlinepart partitions found on MTD device orion_nand [ 2.140900] Creating 5 MTD partitions on "orion_nand": [ 2.146091] 0x000000000000-0x0000000a0000 : "uboot" [ 2.152033] 0x0000000a0000-0x0000000b0000 : "env" [ 2.157793] 0x0000000b0000-0x0000002d8000 : "zImage" [ 2.163853] 0x0000002d8000-0x0000005d8000 : "initrd" [ 2.169910] 0x000000000000-0x000002000000 : "flash"
cat /proc/mtd mtdinfo
Re: Iomega ix4-200d U-boot needed February 04, 2016 03:37AM |
Admin Registered: 13 years ago Posts: 18,900 |
setenv ethaddr xxxxx
Re: Iomega ix4-200d U-boot needed February 04, 2016 03:52AM |
Registered: 8 years ago Posts: 49 |
root@debian:/tools# cat /proc/mtd dev: size erasesize name mtd0: 000a0000 00004000 "uboot" mtd1: 00010000 00004000 "env" mtd2: 00228000 00004000 "zImage" mtd3: 00300000 00004000 "initrd" mtd4: 02000000 00004000 "flash" root@debian:/tools# ./mtdinfo Count of MTD devices: 5 Present MTD devices: mtd0, mtd1, mtd2, mtd3, mtd4 Sysfs interface supported: yes
Re: Iomega ix4-200d U-boot needed February 04, 2016 03:54AM |
Admin Registered: 13 years ago Posts: 18,900 |
mtdinfo -a
Re: Iomega ix4-200d U-boot needed February 04, 2016 04:00AM |
Registered: 8 years ago Posts: 49 |
root@debian:/tools# ./mtdinfo -a Count of MTD devices: 5 Present MTD devices: mtd0, mtd1, mtd2, mtd3, mtd4 Sysfs interface supported: yes mtd0 Name: uboot Type: nand Eraseblock size: 16384 bytes, 16.0 KiB Amount of eraseblocks: 40 (655360 bytes, 640.0 KiB) Minimum input/output unit size: 512 bytes Sub-page size: 256 bytes OOB size: 16 bytes Character device major/minor: 90:0 Bad blocks are allowed: true Device is writable: true mtd1 Name: env Type: nand Eraseblock size: 16384 bytes, 16.0 KiB Amount of eraseblocks: 4 (65536 bytes, 64.0 KiB) Minimum input/output unit size: 512 bytes Sub-page size: 256 bytes OOB size: 16 bytes Character device major/minor: 90:2 Bad blocks are allowed: true Device is writable: true mtd2 Name: zImage Type: nand Eraseblock size: 16384 bytes, 16.0 KiB Amount of eraseblocks: 138 (2260992 bytes, 2.2 MiB) Minimum input/output unit size: 512 bytes Sub-page size: 256 bytes OOB size: 16 bytes Character device major/minor: 90:4 Bad blocks are allowed: true Device is writable: true mtd3 Name: initrd Type: nand Eraseblock size: 16384 bytes, 16.0 KiB Amount of eraseblocks: 192 (3145728 bytes, 3.0 MiB) Minimum input/output unit size: 512 bytes Sub-page size: 256 bytes OOB size: 16 bytes Character device major/minor: 90:6 Bad blocks are allowed: true Device is writable: true mtd4 Name: flash Type: nand Eraseblock size: 16384 bytes, 16.0 KiB Amount of eraseblocks: 2048 (33554432 bytes, 32.0 MiB) Minimum input/output unit size: 512 bytes Sub-page size: 256 bytes OOB size: 16 bytes Character device major/minor: 90:8 Bad blocks are allowed: true Device is writable: true
Re: Iomega ix4-200d U-boot needed February 04, 2016 04:27AM |
Registered: 8 years ago Posts: 49 |
apps 620'602'368 apps.md5 33 config 8'388'608 config.md5 33 content.txt 0 copyjobs.lua 3'127 cpinit 54 enableatmosupgrade.py 1'198 handler.lua 9'766 homeinfo 957 httpd.xml 3'355 initrd 3'031'111 initrd.md5 33 inittab 1'838 iscsicheck 131 iscsicheck.lua 1'281 logrotate.conf 3'025 lvmsetarchive 178 menu.lst 863 networks.lua 10'522 oem 200'704 oem.md5 33 pcre.txt 972 pretty.lua 3'531 quota.lua 1'128 sshdupd.py 736 tz_convert 11'634 uboot_update 378 updateacl 11'446 updateconfig.lua 25'285 upgrade.xml 3'809 upgrade_ix12 2'017 upgrade_ix12_afterboot 3'772 Upgrade_USBShares.py 1'834 Upgrade_USBShares_Mirage.py 852 xml.lua 17'674 zeroconf 672 zImage 2'077'144 zImage.md5 33
Re: Iomega ix4-200d U-boot needed February 04, 2016 01:50PM |
Admin Registered: 13 years ago Posts: 18,900 |
flash_erase /dev/mtd0 0 0 nandwrite /dev/mtd0 mtd0.bin
sync shutdown -r now
setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10' setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x1100000' setenv bootcmd 'run usb_make_boot_args ; run usb_boot; reset' printenv boot
Re: Iomega ix4-200d U-boot needed February 05, 2016 02:13AM |
Registered: 8 years ago Posts: 49 |
root@debian:/tools# ./flash_erase /dev/mtd0 0 40 Erase Total 40 Units Performing Flash Erase of length 16384 at offset 0x9c000 done root@debian:/tools# ./nandwrite /dev/mtd0 mtd0.bin Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x4000 Writing data to block 2 at offset 0x8000 Writing data to block 3 at offset 0xc000 Writing data to block 4 at offset 0x10000 Writing data to block 5 at offset 0x14000 Writing data to block 6 at offset 0x18000 Writing data to block 7 at offset 0x1c000 Writing data to block 8 at offset 0x20000 Writing data to block 9 at offset 0x24000 Writing data to block 10 at offset 0x28000 Writing data to block 11 at offset 0x2c000 Writing data to block 12 at offset 0x30000 Writing data to block 13 at offset 0x34000 Writing data to block 14 at offset 0x38000 Writing data to block 15 at offset 0x3c000 Writing data to block 16 at offset 0x40000 Writing data to block 17 at offset 0x44000 Writing data to block 18 at offset 0x48000 Writing data to block 19 at offset 0x4c000 Writing data to block 20 at offset 0x50000 Writing data to block 21 at offset 0x54000 Writing data to block 22 at offset 0x58000 Writing data to block 23 at offset 0x5c000 Writing data to block 24 at offset 0x60000 Writing data to block 25 at offset 0x64000 Writing data to block 26 at offset 0x68000 Writing data to block 27 at offset 0x6c000 Writing data to block 28 at offset 0x70000 Writing data to block 29 at offset 0x74000 Writing data to block 30 at offset 0x78000 Writing data to block 31 at offset 0x7c000 Writing data to block 32 at offset 0x80000 Writing data to block 33 at offset 0x84000 Writing data to block 34 at offset 0x88000 Writing data to block 35 at offset 0x8c000 Writing data to block 36 at offset 0x90000 Writing data to block 37 at offset 0x94000 Writing data to block 38 at offset 0x98000 Writing data to block 39 at offset 0x9c000 root@debian:/tools# sync root@debian:/tools# shutdown -r now INIT: Switching to r Broadcast message from root@debian (ttyS0) (Fri Feb 5 00:03:42 2016): The system is going down for reboot NOW! [info] Using makefile-style concurrent boot in runlevel 6. [ ok ] Stopping Avahi mDNS/DNS-SD Daemon: avahi-daemon. [....] Stopping busybox' klogd implementation: klogd1862 (klogd) Stopped klogd (pid 1862). . ok [....] Stopping busybox' syslogd implementation: syslogd1859 (syslogd) . ok [ ok ] Stopping NFS kernel daemon: mountd nfsd. [ ok ] Unexporting directories for NFS kernel daemon.... [ ok ] Asking all remaining processes to terminate...done. [ ok ] All processes ended within 1 seconds...done. rpcbind: rpcbind terminating on signal. Restart with "rpcbind -w" [ ok ] Stopping rpcbind daemon.... [ ok ] Stopping NFS common utilities: idmapd statd. [....] Deconfiguring network interfaces...Internet Systems Consortium DHCP Client 4.2.2 Copyright 2004-2011 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:50:43:f6:15:30 Sending on LPF/eth0/00:50:43:f6:15:30 Sending on Socket/fallback DHCPRELEASE on eth0 to 192.168.1.28 port 67 invoke-rc.d: ----------------------------------------------------- invoke-rc.d: WARNING: 'invoke-rc.d ntp try-restart' called invoke-rc.d: during shutdown sequence. invoke-rc.d: enabling safe mode: initscript policy layer disabled invoke-rc.d: ----------------------------------------------------- done. [ ok ] Unmounting temporary filesystems...done. [ ok ] Deactivating swap...done. [info] Will now restart. [ 266.500317] sd 2:0:0:0: [sda] Synchronizing SCSI cache [ 266.506229] reboot: Restarting system __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** uboot_ver:v1.1.1 ** ** MARVELL BOARD: IX4-110 LE U-Boot 1.1.4 (Mar 10 2011 - 15:01:57) Marvell version: 3.4.18 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CF600 Soc: 88F6281 A1 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Found 0x20 i2c device Set Power State as Always On Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:32 MB Found ADT7473, program LED ...(led_volt=90) OK Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp_min=60) OK Marvell Serial ATA Adapter Integrated Sata device found CPU : Marvell Feroceon (Rev 1) Could not found correct initrd Streaming disabled Write allocate disabled Module 0 is RGMII Module 1 is RGMII USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 SCSI: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode flags: 64bit ncq stag led pmp slum part scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: WDC WD20EFRX-68A Rev: 80.0 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 Marvell>> setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10' Marvell>> setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x1100000' Marvell>> setenv bootcmd 'run usb_make_boot_args ; run usb_boot; reset' Marvell>> setenv ethaddr '00:D0:B8:13:AC:24' Marvell>> setenv eth1addr '00:D0:B8:13:AC:23' Marvell>> boot (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found .... ............................................................................................................................................................................................................................................................................................................... 3156720 bytes read .... ............................ ............................................................................................................................................................................................................................................................................................................................................................................................. ........................................................................................................................................................................................................... 6325849 bytes read ## Booting image at 00800000 ... Image Name: Linux-4.2.0-kirkwood-tld-1 Created: 2016-01-29 13:58:29 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3156656 Bytes = 3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-4.2.0-kirkwood-tld-1 Created: 2016-01-22 14:30:27 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6325785 Bytes = 6 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.2.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Aug 31 23:12:00 PDT 2015 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: Iomega ix4-200d [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0xa0000@0x0(uboot),0x10000@0xa0000(env),0x228000@0xb0000(zImage),0x300000@0x2d8000(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 504304K/524288K available (6019K kernel code, 571K rwdata, 1988K rodata, 284K init, 312K bss, 19984K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07da1b4 (8009 kB) [ 0.000000] .init : 0xc07db000 - 0xc0822000 ( 284 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b0e24 ( 572 kB) [ 0.000000] .bss : 0xc08b0e24 - 0xc08ff1a4 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000406] Console: colour dummy device 80x30 [ 0.000435] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.090098] pid_max: default: 32768 minimum: 301 [ 0.090225] Security Framework initialized [ 0.090307] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090326] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091055] Initializing cgroup subsys blkio [ 0.091083] Initializing cgroup subsys devices [ 0.091106] Initializing cgroup subsys freezer [ 0.091138] Initializing cgroup subsys net_cls [ 0.091221] CPU: Testing write buffer coherency: ok [ 0.091605] Setting up static identity map for 0x8200 - 0x8258 [ 0.091869] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.095317] devtmpfs: initialized [ 0.099595] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.100031] prandom: seed boundary self test passed [ 0.103829] prandom: 100 self tests passed [ 0.103853] pinctrl core: initialized pinctrl subsystem [ 0.105181] NET: Registered protocol family 16 [ 0.105598] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130094] cpuidle: using governor ladder [ 0.160090] cpuidle: using governor menu [ 0.160488] Feroceon L2: Enabling L2 [ 0.160532] Feroceon L2: Cache support initialised. [ 0.160901] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.161003] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 0.165949] No ATAGs? [ 0.201540] vgaarb: loaded [ 0.201915] usbcore: registered new interface driver usbfs [ 0.201997] usbcore: registered new interface driver hub [ 0.202064] usbcore: registered new device driver usb [ 0.203150] clocksource: Switched to clocksource orion_clocksource [ 0.259494] NET: Registered protocol family 2 [ 0.260133] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.260194] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.260247] TCP: Hash tables configured (established 4096 bind 4096) [ 0.260309] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.260333] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.260535] NET: Registered protocol family 1 [ 0.260926] RPC: Registered named UNIX socket transport module. [ 0.260939] RPC: Registered udp transport module. [ 0.260947] RPC: Registered tcp transport module. [ 0.260954] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.261219] Unpacking initramfs... [ 0.810427] Freeing initrd memory: 6180K (c1100000 - c1709000) [ 0.810553] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.811621] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.811652] Initialise system trusted keyring [ 0.811760] audit: initializing netlink subsys (disabled) [ 0.811810] audit: type=2000 audit(0.800:1): initialized [ 0.812442] zpool: loaded [ 0.812460] zbud: loaded [ 0.812775] VFS: Disk quotas dquot_6.6.0 [ 0.812836] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.813479] NFS: Registering the id_resolver key type [ 0.813518] Key type id_resolver registered [ 0.813527] Key type id_legacy registered [ 0.813554] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.813570] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.813796] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.814323] Key type big_key registered [ 0.836756] Key type asymmetric registered [ 0.836780] Asymmetric key parser 'x509' registered [ 0.836872] bounce: pool size: 64 pages [ 0.836942] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.836959] io scheduler noop registered [ 0.836972] io scheduler deadline registered [ 0.837028] io scheduler cfq registered (default) [ 0.838337] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.838998] irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated [ 0.839415] irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated [ 0.840244] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00 [ 0.840264] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 0.840277] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 0.840291] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.840649] PCI: bus0: Fast back to back transfers disabled [ 0.840675] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.841453] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.841501] PCI: bus1: Fast back to back transfers disabled [ 0.841669] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 0.841686] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 0.841705] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0000000-0xe00003ff] [ 0.841724] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f] [ 0.841742] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017] [ 0.841760] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f] [ 0.841778] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023] [ 0.841796] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027] [ 0.841812] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.841825] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 0.841840] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 0.842147] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.883841] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy ) [ 0.923823] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy ) [ 0.924037] mv_xor f1060900.xor: Marvell shared XOR driver [ 0.963827] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy ) [ 1.003837] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy ) [ 1.004305] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.005740] console [ttyS0] disabled [ 1.005799] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 1.766094] console [ttyS0] enabled [ 1.770838] nand: device found, Manufacturer ID: 0xec, Chip ID: 0x75 [ 1.777257] nand: Samsung NAND 32MiB 3,3V 8-bit [ 1.781813] nand: 32 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 1.789183] Scanning device for bad blocks [ 2.134620] 5 cmdlinepart partitions found on MTD device orion_nand [ 2.140920] Creating 5 MTD partitions on "orion_nand": [ 2.146110] 0x000000000000-0x0000000a0000 : "uboot" [ 2.152052] 0x0000000a0000-0x0000000b0000 : "env" [ 2.157814] 0x0000000b0000-0x0000002d8000 : "zImage" [ 2.163882] 0x0000002d8000-0x0000005d8000 : "initrd" [ 2.169939] 0x000000000000-0x000002000000 : "flash" [ 2.177359] libphy: Fixed MDIO Bus: probed [ 2.181800] libphy: orion_mdio_bus: probed [ 2.197490] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 3.283803] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:f6:15:30 [ 4.363883] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:50:43:f6:15:31 [ 4.372943] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.379573] ehci-pci: EHCI PCI platform driver [ 4.384130] ehci-orion: EHCI orion driver [ 4.388333] orion-ehci f1050000.ehci: EHCI Host Controller [ 4.393898] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 4.401815] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 4.423185] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 4.429440] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.436290] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.443562] usb usb1: Product: EHCI Host Controller [ 4.448460] usb usb1: Manufacturer: Linux 4.2.0-kirkwood-tld-1 ehci_hcd [ 4.455124] usb usb1: SerialNumber: f1050000.ehci [ 4.460533] hub 1-0:1.0: USB hub found [ 4.464386] hub 1-0:1.0: 1 port detected [ 4.469182] mousedev: PS/2 mouse device common for all mice [ 4.475475] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 4.482549] i2c /dev entries driver [ 4.487585] hidraw: raw HID events driver (C) Jiri Kosina [ 4.493412] drop_monitor: Initializing network drop monitor service [ 4.499946] NET: Registered protocol family 17 [ 4.504559] Key type dns_resolver registered [ 4.509682] Loading compiled-in X.509 certificates [ 4.514557] registered taskstats version 1 [ 4.518731] zswap: loading zswap [ 4.521981] zswap: using zbud pool [ 4.525426] zswap: using lzo compressor [ 4.540220] Key type encrypted registered [ 4.544990] rtc-mv f1010300.rtc: setting system clock to 2016-02-05 08:09:04 UTC (1454659744) [ 4.555876] Freeing unused kernel memory: 284K (c07db000 - c0822000) Loading, please wait... [ 4.634065] udevd[85]: starting version 175 [ 4.783250] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 4.918197] SCSI subsystem initialized [ 4.945095] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 4.951853] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 4.972008] usb 1-1: Product: USB2.0 Hub [ 4.980706] hub 1-1:1.0: USB hub found [ 4.988844] hub 1-1:1.0: 4 ports detected [ 5.014808] pci 0000:00:01.0: enabling device (0140 -> 0143) [ 5.020607] ahci 0000:01:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 5.032908] sata_mv f1080000.sata: slots 32 ports 2 [ 5.081138] scsi host0: sata_mv [ 5.101675] scsi host1: sata_mv [ 5.108876] ata1: SATA max UDMA/133 irq 33 [ 5.112996] ata2: SATA max UDMA/133 irq 33 [ 5.120266] ahci 0000:01:00.0: controller can't do NCQ, turning off CAP_NCQ [ 5.152897] ahci 0000:01:00.0: controller can't do PMP, turning off CAP_PMP [ 5.182711] ahci 0000:01:00.0: masking port_map 0x7 -> 0x3 [ 5.207542] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled [ 5.214449] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 5.222556] ahci 0000:01:00.0: flags: 64bit stag led slum part [ 5.232857] scsi host2: ahci [ 5.236770] scsi host3: ahci [ 5.240555] scsi host4: ahci [ 5.244223] ata3: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000100 irq 84 [ 5.251678] ata4: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000180 irq 84 [ 5.259150] ata5: DUMMY [ 5.283195] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 5.394449] usb 1-1.2: New USB device found, idVendor=125f, idProduct=de7a [ 5.401372] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 5.408770] usb 1-1.2: Product: ADATA USB Flash Drive [ 5.413861] usb 1-1.2: Manufacturer: ADATA [ 5.417977] usb 1-1.2: SerialNumber: 14B1311102300064 [ 5.438974] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 5.445699] scsi host5: usb-storage 1-1.2:1.0 [ 5.451846] usbcore: registered new interface driver usb-storage [ 5.461108] usbcore: registered new interface driver uas [ 5.503211] ata1: SATA link down (SStatus 0 SControl F300) [ 5.603198] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.609953] ata3.00: ATA-9: WDC WD20EFRX-68AX9N0, 80.00A80, max UDMA/133 [ 5.616719] ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 5.624066] ata3.00: configured for UDMA/133 [ 5.873188] ata2: SATA link down (SStatus 0 SControl F300) [ 5.893572] scsi 2:0:0:0: Direct-Access ATA WDC WD20EFRX-68A 0A80 PQ: 0 ANSI: 5 [ 6.253196] ata4: SATA link down (SStatus 0 SControl 300) [ 6.344231] sd 2:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 6.352022] sd 2:0:0:0: [sda] 4096-byte physical blocks [ 6.358673] sd 2:0:0:0: [sda] Write Protect is off [ 6.363705] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.436898] sda: sda1 [ 6.441082] sd 2:0:0:0: [sda] Attached SCSI disk [ 6.447810] scsi 5:0:0:0: Direct-Access ADATA USB Flash Drive 1.00 PQ: 0 ANSI: 6 [ 6.465015] sd 5:0:0:0: [sdb] 123480064 512-byte logical blocks: (63.2 GB/58.8 GiB) [ 6.483290] sd 5:0:0:0: [sdb] Write Protect is off [ 6.488659] sd 5:0:0:0: [sdb] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA [ 6.498297] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 6.507154] sd 5:0:0:0: Attached scsi generic sg1 type 0 [ 6.517873] sdb: sdb1 [ 6.523311] sd 5:0:0:0: [sdb] Attached SCSI removable disk Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 16.832336] EXT3-fs (sdb1): mounted filesystem with ordered data mode [ 16.838952] kjournald starting. Commit interval 5 seconds Begin: Running /scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 17.950206] udevd[309]: starting version 175 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 18.703210] random: nonblocking pool is initialized [ 18.770246] orion_wdt: Initial timeout 21 sec [ 18.783822] adt7475 0-002e: ADT7473 device, revision 0 [ 18.789024] adt7475 0-002e: Optional features: fan4 pwm2 [ 49.133227] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 49.140323] ata3.00: failed command: IDENTIFY DEVICE [ 49.145349] ata3.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 2 pio 512 in [ 49.145349] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 49.159951] ata3.00: status: { DRDY } [ 49.163652] ata3: hard resetting link [ 49.513204] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 49.520575] ata3.00: configured for UDMA/133 [ 49.532750] ata3: EH complete done. [ ok ] Activating swap...done. [....] Checking root file system...fsck from util-linux 2.20.1 rootfs: clean, 15999/3859072 files, 462541/15435004 blocks done. [ 50.645902] EXT3-fs (sdb1): using internal journal [ ok ] Loading kernel modules...done. [ ok ] Cleaning up temporary files... /lib/init/rw. [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.20.1 done. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [....] Configuring network interfaces...[ 55.134566] NET: Registered protocol family 10 Internet Systems Consortium DHCP Client 4.2.2 Copyright 2004-2011 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ [ 56.369692] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Listening on LPF/eth0/00:50:43:f6:15:30 Sending on LPF/eth0/00:50:43:f6:15:30 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11 [ 63.526764] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 63.536682] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPOFFER from 192.168.1.28 DHCPACK from 192.168.1.28 bound to 192.168.0.15 -- renewal in 293 seconds. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 2036 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... [ ok ] Starting system message bus: dbus. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting NTP server: ntpd. [ ok ] Starting rpcbind daemon...[....] Already running.. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting OpenBSD Secure Shell server: sshd. 2035 (klogd) . ok [....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemonTimeout reached while wating for return value Could not receive return value from daemon process. (warning). Debian GNU/Linux 7 debian ttyS0 debian login: root Password: Last login: Fri Feb 5 00:01:38 PST 2016 on ttyS0 Linux debian 4.2.0-kirkwood-tld-1 #1 PREEMPT Mon Aug 31 23:12:00 PDT 2015 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~#
Re: Iomega ix4-200d U-boot needed February 05, 2016 02:53AM |
Admin Registered: 13 years ago Posts: 18,900 |
Marvell>> setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10' Marvell>> setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x1100000' Marvell>> setenv bootcmd 'run usb_make_boot_args ; run usb_boot; reset' Marvell>> setenv ethaddr '00:D0:B8:13:AC:24' Marvell>> setenv eth1addr '00:D0:B8:13:AC:23' Marvell>> saveenv Marvell>> boot
Re: Iomega ix4-200d U-boot needed February 05, 2016 03:13AM |
Admin Registered: 13 years ago Posts: 18,900 |
# MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x00000 0x10000 0x4000
fw_printenv
Re: Iomega ix4-200d U-boot needed February 05, 2016 03:49AM |
Registered: 8 years ago Posts: 49 |
Re: Iomega ix4-200d U-boot needed February 09, 2016 03:52AM |
Registered: 8 years ago Posts: 49 |
Re: Iomega ix4-200d U-boot needed February 09, 2016 11:34AM |
Admin Registered: 13 years ago Posts: 18,900 |
Re: Iomega ix4-200d U-boot needed February 10, 2016 12:30AM |
Admin Registered: 13 years ago Posts: 18,900 |
./blparam
Re: Iomega ix4-200d U-boot needed February 10, 2016 01:19AM |
Registered: 8 years ago Posts: 49 |