|
Problem booting with Arch U-Boot 2016.09.01-1 February 05, 2017 08:12PM |
Registered: 10 years ago Posts: 7 |
U-Boot 2016.09.01-1 (Oct 10 2016 - 23:12:58 -0600) Arch Linux ARM
Pogo E02
gcc (GCC) 6.2.1 20160830
GNU ld (GNU Binutils) 2.27
Hit any key to stop autoboot: 0
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
USB device 0:
Device 0: Vendor: Ext Hard Rev: Prod: Disk
Type: Hard Disk
Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
... is now current device
usb found on device 0
Checking for: /boot/uEnv.txt ...
** File not found /boot/zImage **
4603360 bytes read in 545 ms (8.1 MiB/s)
loading /boot/dtbs/kirkwood-pogo_e02.dtb ...
** File not found /boot/dtbs/kirkwood-pogo_e02.dtb **
4352795 bytes read in 554 ms (7.5 MiB/s)
Booting uImage with initrd
## Booting kernel from Legacy Image at 00810000 ...
Image Name: Linux-4.4.28-1-ARCH
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4603296 Bytes = 4.4 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.28-1-ARCH (builduser@leming) (gcc version 6.2.120160830 (GCC) ) #1 PREEMPT Sat Oct 29 00:27:49 MDT 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Pogoplug E02 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] free_area_init_node: node 0, pgdat c0918bd4, node_mem_map cfdba000 [ 0.000000] Normal zone: 576 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65536 pages, LIFO batch:15 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64960 [ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:1M(u-boot),-(rootfs) root=PARTUUID=4131cea8-01 rw rootwait ignore_loglevel netconso le=6665@10.10.10.3/eth0,6666@10.10.10.4/ [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 245264K/262144K available (6597K kernel code, 547K rwdata, 1876K rodata, 300K init, 725K bss, 16880K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc084e9a4 (8475 kB) [ 0.000000] .init : 0xc084f000 - 0xc089a000 ( 300 kB) [ 0.000000] .data : 0xc089a000 - 0xc0922e0c ( 548 kB) [ 0.000000] .bss : 0xc0922e0c - 0xc09d83d8 ( 726 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:114 [ 0.000013] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 10.814887] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 10.815077] Console: colour dummy device 80x30 [ 10.815106] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 10.904972] pid_max: default: 32768 minimum: 301 [ 10.905068] Security Framework initialized [ 10.905146] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 10.905164] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 10.905907] Initializing cgroup subsys io [ 10.905939] Initializing cgroup subsys memory [ 10.905991] Initializing cgroup subsys devices [ 10.906017] Initializing cgroup subsys freezer [ 10.906037] Initializing cgroup subsys net_cls [ 10.906054] Initializing cgroup subsys perf_event [ 10.906076] Initializing cgroup subsys net_prio [ 10.906159] CPU: Testing write buffer coherency: ok [ 10.906621] Setting up static identity map for 0x81e0 - 0x8238 [ 10.908577] devtmpfs: initialized [ 10.910994] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 10.911433] pinctrl core: initialized pinctrl subsystem [ 10.912224] NET: Registered protocol family 16 [ 10.912763] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 10.934975] cpuidle: using governor ladder [ 10.964974] cpuidle: using governor menu [ 10.965187] Kirkwood: MV88F6281-A0, TCLK=200000000. [ 10.965212] Feroceon L2: Enabling L2 [ 10.965250] Feroceon L2: Cache support initialised. [ 10.966000] initial MPP regs: 01111111 11113322 00001111 00100000 00000000 00 000000 00000000 [ 10.966027] final MPP regs: 01111111 11113322 00001111 00000000 00000000 00000000 00000000 [ 11.006484] vgaarb: loaded [ 11.006816] SCSI subsystem initialized [ 11.007003] libata version 3.00 loaded. [ 11.007302] usbcore: registered new interface driver usbfs [ 11.007377] usbcore: registered new interface driver hub [ 11.007438] usbcore: registered new device driver usb [ 11.007610] pps_core: LinuxPPS API ver. 1 registered [ 11.007619] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 11.007653] PTP clock support registered [ 11.008757] clocksource: Switched to clocksource orion_clocksource [ 11.047473] FS-Cache: Loaded [ 11.060697] NET: Registered protocol family 2 [ 11.061522] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 11.061560] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 11.061591] TCP: Hash tables configured (established 2048 bind 2048) [ 11.061664] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 11.061687] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 11.061876] NET: Registered protocol family 1 [ 11.062202] RPC: Registered named UNIX socket transport module. [ 11.062214] RPC: Registered udp transport module. [ 11.062221] RPC: Registered tcp transport module. [ 11.062227] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 11.062248] PCI: CLS 0 bytes, default 32 [ 11.062518] Trying to unpack rootfs image as initramfs... [ 11.435303] Freeing initrd memory: 4252K (c1100000 - c1527000) [ 11.437191] futex hash table entries: 256 (order: -1, 3072 bytes) [ 11.450062] VFS: Disk quotas dquot_6.6.0 [ 11.450319] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 11.452372] FS-Cache: Netfs 'nfs' registered for caching [ 11.453483] NFS: Registering the id_resolver key type [ 11.453545] Key type id_resolver registered [ 11.453554] Key type id_legacy registered [ 11.453638] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 11.454953] fuse init (API version 7.23) [ 11.457186] aufs 4.4-20160912 [ 11.462612] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 11.462637] io scheduler noop registered [ 11.462653] io scheduler deadline registered [ 11.462929] io scheduler cfq registered [ 11.463197] io scheduler bfq registered (default) [ 11.463206] BFQ I/O-scheduler: v7r11 [ 11.463403] mv_xor mv_xor.0: Marvell shared XOR driver [ 11.500056] mv_xor mv_xor.0: Marvell XOR (Registers Mode): ( xor cpy ) [ 11.500305] mv_xor mv_xor.1: Marvell shared XOR driver [ 11.540019] mv_xor mv_xor.1: Marvell XOR (Registers Mode): ( xor cpy ) [ 11.545695] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 11.546820] console [ttyS0] disabled [ 11.566954] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 12500000) is a 16550A [ 12.200472] console [ttyS0] enabled [ 12.219879] brd: module loaded [ 12.230721] loop: module loaded [ 12.234675] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 12.241167] nand: Samsung NAND 128MiB 3,3V 8-bit [ 12.245809] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 12.253442] Scanning device for bad blocks [ 12.305811] Bad eraseblock 636 at 0x000004f80000 [ 12.311336] Bad eraseblock 648 at 0x000005100000 [ 12.344388] 2 cmdlinepart partitions found on MTD device orion_nand [ 12.350698] Creating 2 MTD partitions on "orion_nand": [ 12.355859] 0x000000000000-0x000000100000 : "u-boot" [ 12.361344] 0x000000100000-0x000008000000 : "rootfs" [ 12.379832] libphy: orion_mdio_bus: probed [ 12.384067] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 13.469710] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:02:24:78 [ 13.478592] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 13.485182] ehci-pci: EHCI PCI platform driver [ 13.489733] ehci-orion: EHCI orion driver [ 13.493837] orion-ehci orion-ehci.0: EHCI Host Controller [ 13.499319] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 13.507065] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 13.528788] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 13.535717] hub 1-0:1.0: USB hub found [ 13.539583] hub 1-0:1.0: 1 port detected [ 13.544232] usbcore: registered new interface driver uas [ 13.549763] usbcore: registered new interface driver usb-storage [ 13.555851] usbcore: registered new interface driver ums-alauda [ 13.561900] usbcore: registered new interface driver ums-cypress [ 13.567987] usbcore: registered new interface driver ums-datafab [ 13.574096] usbcore: registered new interface driver ums_eneub6250 [ 13.580381] usbcore: registered new interface driver ums-freecom [ 13.586465] usbcore: registered new interface driver ums-isd200 [ 13.592485] usbcore: registered new interface driver ums-jumpshot [ 13.598655] usbcore: registered new interface driver ums-karma [ 13.604589] usbcore: registered new interface driver ums-onetouch [ 13.610809] usbcore: registered new interface driver ums-realtek [ 13.616898] usbcore: registered new interface driver ums-sddr09 [ 13.622920] usbcore: registered new interface driver ums-sddr55 [ 13.628944] usbcore: registered new interface driver ums-usbat [ 13.635254] mousedev: PS/2 mouse device common for all mice [ 13.858789] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 14.011333] hub 1-1:1.0: USB hub found [ 14.015451] hub 1-1:1.0: 4 ports detected [ 14.298780] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 14.412253] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 14.418902] scsi host0: usb-storage 1-1.1:1.0 [ 14.648781] rtc-mv rtc-mv: internal RTC not ticking [ 14.653828] i2c /dev entries driver [ 14.657912] sdhci: Secure Digital Host Controller Interface driver [ 14.664143] sdhci: Copyright(c) Pierre Ossman [ 14.668584] sdhci-pltfm: SDHCI platform and OF driver helper [ 14.674793] ledtrig-cpu: registered to indicate activity on CPUs [ 14.680997] usbcore: registered new interface driver r8712u [ 14.686843] gre: GRE over IPv4 demultiplexor driver [ 14.691811] NET: Registered protocol family 17 [ 14.696403] Key type dns_resolver registered [ 14.701743] registered taskstats version 1 [ 14.726635] Key type encrypted registered [ 14.731352] netpoll: netconsole: local port 6665 [ 14.735996] netpoll: netconsole: local IPv4 address 10.10.10.3 [ 14.742062] netpoll: netconsole: interface 'eth0' [ 14.746790] netpoll: netconsole: remote port 6666 [ 14.751573] netpoll: netconsole: remote IPv4 address 10.10.10.4 [ 14.757516] netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff [ 14.764470] netpoll: netconsole: device eth0 not up yet, forcing it [ 15.429412] scsi 0:0:0:0: Direct-Access Ext Hard Disk PQ0 ANSI: 4 [ 15.438988] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298GiB) [ 15.458781] sd 0:0:0:0: [sda] Write Protect is off [ 15.463615] sd 0:0:0:0: [sda] Mode Sense: 10 00 00 00 [ 15.469349] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 15.478822] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 15.527671] sda: sda1 sda2 [ 15.541226] sd 0:0:0:0: [sda] Attached SCSI disk [ 17.558659] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, fullduplex, flow control disabled [ 17.571608] console [netcon0] enabled [ 17.575307] netconsole: network logging started [ 17.580010] hctosys: unable to open rtc device (rtc0) [ 17.587044] Freeing unused kernel memory: 300K (c084f000 - c089a000) [ 17.656568] random: systemd-tmpfile: uninitialized urandom read (16 bytes read, 24 bits of entropy available) [ 17.688403] random: udevadm: uninitialized urandom read (16 bytes read, 24 bits of entropy available) [ 17.700369] random: systemd-udevd: uninitialized urandom read (16 bytes read,24 bits of entropy available) [ 17.710699] random: systemd-udevd: uninitialized urandom read (16 bytes read,24 bits of entropy available) [ 17.837882] random: udevadm: uninitialized urandom read (16 bytes read, 24 bits of entropy available) [ 17.868645] random: udevadm: uninitialized urandom read (16 bytes read, 24 bits of entropy available) [ 17.898130] random: udevadm: uninitialized urandom read (16 bytes read, 25 bits of entropy available) [ 17.927046] random: udevadm: uninitialized urandom read (16 bytes read, 25 bits of entropy available) [ 17.956580] random: udevadm: uninitialized urandom read (16 bytes read, 25 bits of entropy available) [ 17.986119] random: udevadm: uninitialized urandom read (16 bytes read, 25 bits of entropy available) [ 19.346124] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 19.378213] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:(null) [ 20.939703] systemd[1]: System time before build time, advancing clock. [ 21.207620] NET: Registered protocol family 10 [ 21.265233] ip_tables: (C) 2000-2006 Netfilter Core Team [ 21.354915] systemd[1]: systemd 231 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 21.373536] systemd[1]: Detected architecture arm. [ 21.421336] systemd[1]: Set hostname to <alarm>. [ 22.859494] random: nonblocking pool is initialized [ 23.009946] systemd[1]: Reached target Remote File Systems. [ 23.041898] systemd[1]: Created slice System Slice. [ 23.069904] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 23.099906] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 23.129311] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 23.159203] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 23.190075] systemd[1]: Created slice system-netctl\x2difplugd.slice. [ 23.219232] systemd[1]: Listening on LVM2 metadata daemon socket. [ 23.249251] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 23.278985] systemd[1]: Reached target Paths. [ 23.299157] systemd[1]: Listening on Device-mapper event daemon FIFOs. [ 23.328986] systemd[1]: Reached target Encrypted Volumes. [ 23.359197] systemd[1]: Listening on udev Control Socket. [ 23.395280] systemd[1]: Listening on Process Core Dump Socket. [ 23.465238] systemd[1]: Listening on Journal Socket. [ 23.492778] systemd[1]: Mounting POSIX Message Queue File System... [ 23.539416] systemd[1]: Mounting Debug File System... [ 23.615381] systemd[1]: Starting Create list of required static device nodesfor the current kernel... [ 23.663141] systemd[1]: Starting Remount Root and Kernel File Systems... [ 23.713542] systemd[1]: Starting Setup Virtual Console... [ 23.799431] systemd[1]: Starting Apply Kernel Variables... [ 23.823981] systemd[1]: Mounting FUSE Control File System... [ 23.865678] EXT4-fs (sda1): re-mounted. Opts: (null) [ 23.885705] systemd[1]: Listening on Journal Socket (/dev/log). [ 23.963361] systemd[1]: Starting Journal Service... [ 23.989433] systemd[1]: Listening on udev Kernel Socket. [ 24.003694] systemd[1]: Created slice User and Session Slice. [ 24.059124] systemd[1]: Reached target Slices. [ 24.080009] systemd[1]: Created slice system-getty.slice. [ 24.129291] systemd[1]: Mounted Debug File System. [ 24.149215] systemd[1]: Mounted FUSE Control File System. [ 24.179118] systemd[1]: Mounted POSIX Message Queue File System. [ 24.211566] systemd[1]: Started Create list of required static device nodes for the current kernel. [ 24.241247] systemd[1]: Started Remount Root and Kernel File Systems. [ 24.270676] systemd[1]: Started Setup Virtual Console. [ 24.315413] systemd-journald[176]: File /var/log/journal/e4b5dad211aa4a41920893d218a05e68/system.journal corrupted or uncleanly shut down, renaming and replacing. [ 24.344412] systemd[1]: Starting Load/Save Random Seed... [ 24.499649] systemd[1]: Starting udev Coldplug all Devices... [ 24.534434] systemd[1]: Starting Create Static Device Nodes in /dev... [ 24.680358] systemd[1]: Started Load/Save Random Seed. [ 25.116204] systemd[1]: Started udev Coldplug all Devices. [ 25.208272] systemd[1]: Started Create Static Device Nodes in /dev. [ 25.264499] systemd[1]: Starting udev Kernel Device Manager... [ 25.297265] systemd[1]: Reached target Local File Systems (Pre). [ 25.491368] systemd[1]: Started Journal Service. [ 25.700643] systemd-journald[176]: Received request to flush runtime journal from PID 1 [ 26.244712] MV-CESA:Could not register sha1 driver [ 26.265748] MV-CESA:Could not register hmac-sha1 driver [ 27.518991] EXT4-fs (sda2): mounting ext3 file system using the ext4 subsystem [ 27.614092] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts:(null) [ 30.329090] Adding 1048572k swap on /media/usb/swapfile.img. Priority:-1 extents:265 across:1082584k
|
Re: Problem booting with Arch U-Boot 2016.09.01-1 February 05, 2017 09:42PM |
Admin Registered: 13 years ago Posts: 18,896 |
|
Re: Problem booting with Arch U-Boot 2016.09.01-1 February 05, 2017 10:22PM |
Registered: 10 years ago Posts: 7 |
|
Re: Problem booting with Arch U-Boot 2016.09.01-1 February 06, 2017 02:41PM |
Registered: 10 years ago Posts: 7 |
PogoE02> print
print
bootcmd=run startboot;run bootubi
bootdir=/boot
bootfilem=uImage
bootfilez=zImage
bootubi=echo Trying to boot from NAND ...;if run mountubi; then ubifsload ${loadaddr} /boot/zImage;ubifsload ${fdtaddr} /boot/dtbs/${fdtfile};ubifsumount; setenv bootargs console=${console} ubi.mtd=1 root=ubi0:rootfs ro rootfstype=ubifs rootwait ${mtdparts};bootz ${loadaddr} - ${fdtaddr};fi
console=ttyS0,115200
devnum=0
ethact=egiga0
ethaddr=00:25:31:02:24:78
fdtaddr=0x800000
fdtdir=/boot/dtbs
fdtfile=kirkwood-pogo_e02.dtb
ipaddr=10.10.10.3
loadaddr=0x810000
loadfdt=echo loading ${fdtdir}/${fdtfile} ...; load ${devtype} ${bootpart} ${fdtaddr} ${fdtdir}/${fdtfile}
loadimage=load ${devtype} ${bootpart} ${loadaddr} ${bootdir}/${bootfilez} || load ${devtype} ${bootpart} ${loadaddr} ${bootdir}/${bootfilem}
loadrd=load ${devtype} ${bootpart} ${rdaddr} ${bootdir}/${rdfile}
mainargs=setenv bootargs console=${console} ${mtdparts} root=${root} rw rootwait ${optargs} ${ncargs}
mountubi=ubi part rootfs; ubifsmount ubi0:rootfs
mtddevname=u-boot
mtddevnum=0
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),-(rootfs)
nand_erasesize=20000
nand_oobsize=40
nand_writesize=800
ncargs=ignore_loglevel netconsole=6665@10.10.10.3/eth0,6666@10.10.10.4/
ncip=10.10.10.5
ncipk=10.10.10.4
netconsole=on
partition=nand0,0
preboot=if env exists netconsole && test ${netconsole} = on; then if ping ${ncip}; then setenv stdin nc; setenv stdout nc; setenv stderr nc; version; if env exists ncargsusr; then echo ncargs has been defined by user; setenv ncargs ${ncargsusr}; else setenv ncargs ignore_loglevel netconsole=6665@${ipaddr}/eth0,6666@${ncipk}/; fi; fi; else echo Netconsole has been turned off.; echo To turn it on, set netconsole variable to on.; setenv stdin; setenv stdout; setenv stderr; setenv ncargs; fi
rdaddr=0x1100000
rdfile=initramfs-linux.img
startboot=usb start; for devtype in usb ; do setenv devnum 0; while ${devtype} dev ${devnum}; do echo ${devtype} found on device ${devnum}; setenv bootpart ${devnum}:1; echo Checking for: ${bootdir}/uEnv.txt ...; if test -e ${devtype} ${bootpart} ${bootdir}/uEnv.txt; then load ${devtype} ${bootpart} ${loadaddr} ${bootdir}/uEnv.txt; env import -t ${loadaddr} ${filesize}; echo Loaded environment from ${bootdir}/uEnv.txt; echo Checking if uenvcmd is set ...; if test -n ${uenvcmd}; then echo Running uenvcmd ...; run uenvcmd; fi; fi; if run loadimage; then if env exists root; then echo root has been defined by user; else part uuid ${devtype} ${bootpart} uuid; setenv root PARTUUID=${uuid}; fi; run mainargs; if run loadfdt; then if run loadrd; then bootz ${loadaddr} ${rdaddr}:${filesize} ${fdtaddr}; else bootz ${loadaddr} - ${fdtaddr}; fi; else if run loadrd; then echo Booting uImage with initrd; bootm ${loadaddr} ${rdaddr}:${filesize}; else bootm ${loadaddr}; fi; fi; else echo No kernel found; fi; setexpr devnum ${devnum} + 1; done; done;
stderr=nc
stdin=nc
stdout=nc
Environment size: 3014/131068 bytes
PogoE02>
|
Re: Problem booting with Arch U-Boot 2016.09.01-1 February 06, 2017 10:04PM |
Registered: 10 years ago Posts: 7 |
|
Re: Problem booting with Arch U-Boot 2016.09.01-1 February 07, 2017 12:55AM |
Admin Registered: 13 years ago Posts: 18,896 |