GoFlexHome u-boot 2017-07-tld-1 November 12, 2017 02:56PM |
Registered: 6 years ago Posts: 337 |
Re: GoFlexHome u-boot 2017-07-tld-1 November 12, 2017 05:26PM |
Admin Registered: 13 years ago Posts: 18,613 |
Quote
> I'm trying to update u-boot on a GoFlexHome dock
> according to instructions here:-
>
> https://forum.doozan.com/read.php?3,12381
>
> I've downloaded
> uboot.2017.07-tld-1.goflexhome.bodhi.tar from
> https://bitly.com/2zQWP4Y , and made sure I made
> the appropriate tools.
>
> /etc/fw_env.config has been copied
>
> running cat /proc/mtd gives me:-
>
> dev: size erasesize name
> mtd0: 00100000 00020000 "u-boot"
> mtd2: 0ff00000 00020000 "rootfs"
>
> rather than what it suggested:-
>
> dev: size erasesize name
> mtd0: 00100000 00020000 "u-boot"
> mtd1: 00400000 00020000 "uImage"
> mtd2: 02000000 00020000 "rootfs"
> mtd3: 0db00000 00020000 "data"
>
> ...so I'm not at sure how to proceed.
> mtd0: 00100000 00020000 "u-boot" > mtd0: 00100000 00020000 "u-boot"
Re: GoFlexHome u-boot 2017-07-tld-1 November 13, 2017 03:01AM |
Registered: 6 years ago Posts: 337 |
fw_setenv mtdparts 'xxxxxxxxx' fw_setenv ethaddr 'xx:xx:xx:xx:xx:xx'
Re: GoFlexHome u-boot 2017-07-tld-1 November 13, 2017 04:26AM |
Admin Registered: 13 years ago Posts: 18,613 |
fw_setenv mtdparts 'mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)'
Re: GoFlexHome u-boot 2017-07-tld-1 November 13, 2017 10:54AM |
Registered: 6 years ago Posts: 337 |
Re: GoFlexHome u-boot 2017-07-tld-1 November 13, 2017 12:25PM |
Registered: 6 years ago Posts: 337 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:21:31 -0700) Seagate GoFlex Home Hit any key to stop autoboot: 10 9 8 7 6 5 4 3 2 1 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: ide_preinit failed Unknown command 'mmc' - try 'help' Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 15278144 41e49ae4-01 83 Boot ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... 747 bytes read in 830 ms (0 Bytes/s) no IDE devices available Unknown command 'mmc' - try 'help' importing envs ... running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 661 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 3154896 bytes read in 1129 ms (2.7 MiB/s) loading uInitrd ... 7179935 bytes read in 1169 ms (5.9 MiB/s) loading DTB /boot/dts/kirkwood-goflexhome.dtb ... 10605 bytes read in 2721 ms (2.9 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Created: 2016-02-19 5:55:25 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3154832 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Created: 2016-02-19 7:33:04 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Starting kernel ...
Re: GoFlexHome u-boot 2017-07-tld-1 November 13, 2017 04:15PM |
Admin Registered: 13 years ago Posts: 18,613 |
Quote
> U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:21:31
> -0700)
> Seagate GoFlex Home
> Found bootable drive on usb 0
> loading uImage ...
> 3154896 bytes read in 1129 ms (2.7 MiB/s)
> loading uInitrd ...
> 7179935 bytes read in 1169 ms (5.9 MiB/s)
> loading DTB /boot/dts/kirkwood-goflexhome.dtb ...
> 10605 bytes read in 2721 ms (2.9 KiB/s)
> ## Booting kernel from Legacy Image at 00800000
> ...
> Image Name: Linux-4.4.0-kirkwood-tld-1
> Created: 2016-02-19 5:55:25 UTC
> Image Type: ARM Linux Kernel Image
> (uncompressed)
> Data Size: 3154832 Bytes = 3 MiB
> Load Address: 00008000
> Entry Point: 00008000
> Verifying Checksum ... OK
> ## Loading init Ramdisk from Legacy Image at
> 01100000 ...
> Image Name: initramfs-4.4.0-kirkwood-tld-1
> Created: 2016-02-19 7:33:04 UTC
> Image Type: ARM Linux RAMDisk Image (gzip
> compressed)
> Data Size: 7179871 Bytes = 6.8 MiB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
> ## Flattened Device Tree blob at 01c00000
> Booting using the fdt blob at 0x1c00000
>
> Starting kernel ...
>
ping debian.local
ssh root@debian.local
Re: GoFlexHome u-boot 2017-07-tld-1 November 13, 2017 04:15PM |
Admin Registered: 13 years ago Posts: 18,613 |
LABEL=rootfs / ext3 noatime,errors=remount-ro 0 1