U-Boot Kirkwood - NSA310 - nandump segfault March 01, 2020 03:47PM |
Registered: 5 years ago Posts: 29 |
/mnt/testmount/tools # cat /etc/fw_env.config # Configuration file for fw_(printenv/saveenv) utility. # Up to two entries are valid, in this case the redundand # environment sector is assumed present. # Notice, that the "Number of sectors" is ignored on NOR. # MTD device name Device offset Env. size Flash sector size Number of sectors # NAND example /dev/mtd1 0x0000 0x20000 0x20000 4
/mnt/testmount/tools # cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "uboot" mtd1: 00080000 00020000 "uboot_env" mtd2: 00080000 00020000 "key_store" mtd3: 00080000 00020000 "info" mtd4: 00a00000 00020000 "etc" mtd5: 00a00000 00020000 "kernel_1" mtd6: 02fc0000 00020000 "rootfs1" mtd7: 00a00000 00020000 "kernel_2" mtd8: 02fc0000 00020000 "rootfs2"
/mnt/testmount/tools # ./nanddump --noecc --omitoob -l 0x80000 -f mtd0 /dev/mtd0Segmentation fault
20:37:30.619 -> | \/ | __ _ _ ____ _____| | | 20:37:30.619 -> | |\/| |/ _` | '__\ \ / / _ \ | | 20:37:30.619 -> | | | | (_| | | \ V / __/ | | 20:37:30.619 -> |_| |_|\__,_|_| \_/ \___|_|_| 20:37:30.619 -> _ _ ____ _ 20:37:30.619 -> | | | | | __ ) ___ ___ | |_ 20:37:30.619 -> | | | |___| _ \ / _ \ / _ \| __| 20:37:30.619 -> | |_| |___| |_) | (_) | (_) | |_ 20:37:30.619 -> \___/ |____/ \___/ \___/ \__| 20:37:30.619 -> ** MARVELL BOARD: RD-88F6281A LE 20:37:30.619 -> 20:37:30.619 -> U-Boot 1.1.4 (Feb 22 2011 - 10:31:35) Marvell version: 3.4.19 20:37:30.619 -> 20:37:30.619 -> U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFEE0 20:37:30.685 -> 20:37:30.685 -> Soc: 88F6281 A1 (DDR2) 20:37:30.685 -> CPU running @ 1200Mhz L2 running @ 400Mhz 20:37:30.685 -> SysClock = 400Mhz , TClock = 200Mhz 20:37:30.685 -> 20:37:30.685 -> DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 20:37:30.685 -> DRAM CS[0] base 0x00000000 size 256MB 20:37:30.685 -> DRAM Total size 256MB 16bit width 20:37:30.685 -> Addresses 10M - 0M are saved for the U-Boot usage. 20:37:30.685 -> Mem malloc Initialization (10M - 7M): Done 20:37:30.738 -> NAND:128 MB 20:37:31.781 -> Flash: 0 kB 20:37:31.814 -> 20:37:31.814 -> CPU : Marvell Feroceon (Rev 1) 20:37:32.379 -> Kernel address is 0xc80000. 20:37:32.379 -> 20:37:32.379 -> Streaming disabled 20:37:32.379 -> Write allocate disabled 20:37:32.379 -> 20:37:32.379 -> Module 0 is RGMII 20:37:32.379 -> Module 1 is TDM 20:37:32.379 -> 20:37:32.379 -> USB 0: host mode 20:37:32.911 -> PEX 0: PCI Express Root Complex Interface 20:37:32.911 -> PEX interface detected Link X1 20:37:32.944 -> Net: egiga0, egiga1 [PRIME] 20:37:32.977 -> Hit any key to stop autoboot: 2 1 0 20:37:34.969 -> 20:37:34.969 -> NAND read: device 0 offset 0xc80000, size 0xa00000 20:37:35.002 -> 20:37:35.002 -> Reading data from 0xc80000 -- 0% complete. [...] Reading data from 0x167f800 -- 100% complete. 20:37:41.976 -> 10485760 bytes read: OK 20:37:41.976 -> ## Booting image at 02000000 ... 20:37:41.976 -> Image Name: Linux-2.6.22.18 20:37:41.976 -> Created: 2011-02-22 3:33:51 UTC 20:37:41.976 -> Image Type: ARM Linux Kernel Image (uncompressed) 20:37:41.976 -> Data Size: 5701144 Bytes = 5.4 MB 20:37:41.976 -> Load Address: 00008000 20:37:41.976 -> Entry Point: 00008000 20:37:41.976 -> Verifying Checksum ... OK 20:37:43.304 -> OK 20:37:43.304 -> 20:37:43.304 -> Starting kernel ...
/mnt/testmount/tools # mount rootfs on / type rootfs (rw) /proc on /proc type proc (rw) /sys on /sys type sysfs (rw) none on /proc/bus/usb type usbfs (rw) /dev/mtdblock6 on /zyxel/mnt/nand type yaffs2 (ro) /dev/sda1 on /zyxel/mnt/sysdisk type ext3 (ro,data=ordered) /dev/loop0 on /ram_bin type ext2 (ro) /dev/loop0 on /usr type ext2 (ro) /dev/loop0 on /lib/security type ext2 (ro) /dev/loop0 on /lib/modules type ext2 (ro) /dev/ram0 on /tmp/tmpfs type tmpfs (rw) /dev/ram0 on /usr/local/etc type tmpfs (rw) /dev/ram0 on /usr/local/var type tmpfs (rw) /dev/mtdblock4 on /etc/zyxel type yaffs2 (rw) /dev/md0 on /i-data/3c7e9e7c type xfs (rw,usrquota,nouuid) /dev/md0 on /i-data/3c7e9e7c/.media/mbvideo/Musik type xfs (rw,usrquota,nouuid) /dev/md0 on /i-data/3c7e9e7c/.media/mbvideo/Billeder type xfs (rw,usrquota,nouuid) /dev/md0 on /i-data/3c7e9e7c/.media/mbvideo/Videoer type xfs (rw,usrquota,nouuid) /dev/md0 on /i-data/3c7e9e7c/.media/mbvideo/Dokumenter type xfs (rw,usrquota,nouuid) /dev/md0 on /usr/local/apache/web_framework/data/cache type xfs (rw,usrquota,nouuid) /dev/mtdblock4 on /usr/local/apache/web_framework/data/config type yaffs2 (rw) /dev/md0 on /usr/local/zy-pkgs type xfs (rw,usrquota,nouuid) /dev/md0 on /etc/zyxel/zy-pkgs type xfs (rw,usrquota,nouuid) /dev/md0 on /usr/local/apache/htdocs/zyxel/pkg type xfs (rw,usrquota,nouuid) /dev/sdb1 on /mnt/testmount type ext3 (rw,data=ordered) /mnt/testmount/tools #
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 01, 2020 05:15PM |
Admin Registered: 14 years ago Posts: 19,425 |
> /mnt/testmount/tools # cat /proc/mtd > dev: size erasesize name > mtd0: 00100000 00020000 "uboot" > mtd1: 00080000 00020000 "uboot_env" > mtd2: 00080000 00020000 "key_store" > mtd3: 00080000 00020000 "info" > mtd4: 00a00000 00020000 "etc" > mtd5: 00a00000 00020000 "kernel_1" > mtd6: 02fc0000 00020000 "rootfs1" > mtd7: 00a00000 00020000 "kernel_2" > mtd8: 02fc0000 00020000 "rootfs2" >
cat /proc/mtd
dmesg cat /proc/mtd
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 02, 2020 12:40AM |
Registered: 5 years ago Posts: 29 |
07:36:33.516 -> ⸮ 07:36:33.516 -> __ __ _ _ 07:36:33.516 -> | \/ | __ _ _ ____ _____| | | 07:36:33.516 -> | |\/| |/ _` | '__\ \ / / _ \ | | 07:36:33.516 -> | | | | (_| | | \ V / __/ | | 07:36:33.516 -> |_| |_|\__,_|_| \_/ \___|_|_| 07:36:33.516 -> _ _ ____ _ 07:36:33.516 -> | | | | | __ ) ___ ___ | |_ 07:36:33.516 -> | | | |___| _ \ / _ \ / _ \| __| 07:36:33.516 -> | |_| |___| |_) | (_) | (_) | |_ 07:36:33.516 -> \___/ |____/ \___/ \___/ \__| 07:36:33.516 -> ** MARVELL BOARD: RD-88F6281A LE 07:36:33.516 -> 07:36:33.516 -> U-Boot 1.1.4 (Feb 22 2011 - 10:31:35) Marvell version: 3.4.19 07:36:33.516 -> 07:36:33.516 -> U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFEE0 07:36:33.547 -> 07:36:33.547 -> Soc: 88F6281 A1 (DDR2) 07:36:33.547 -> CPU running @ 1200Mhz L2 running @ 400Mhz 07:36:33.547 -> SysClock = 400Mhz , TClock = 200Mhz 07:36:33.547 -> 07:36:33.547 -> DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 07:36:33.547 -> DRAM CS[0] base 0x00000000 size 256MB 07:36:33.547 -> DRAM Total size 256MB 16bit width 07:36:33.547 -> Addresses 10M - 0M are saved for the U-Boot usage. 07:36:33.547 -> Mem malloc Initialization (10M - 7M): Done 07:36:33.597 -> NAND:128 MB 07:36:34.677 -> Flash: 0 kB 07:36:34.710 -> 07:36:34.710 -> CPU : Marvell Feroceon (Rev 1) 07:36:35.242 -> Kernel address is 0xc80000. 07:36:35.275 -> 07:36:35.275 -> Streaming disabled 07:36:35.275 -> Write allocate disabled 07:36:35.275 -> 07:36:35.275 -> Module 0 is RGMII 07:36:35.275 -> Module 1 is TDM 07:36:35.275 -> 07:36:35.275 -> USB 0: host mode 07:36:35.774 -> PEX 0: PCI Express Root Complex Interface 07:36:35.774 -> PEX interface detected Link X1 07:36:35.807 -> Net: egiga0, egiga1 [PRIME] 07:36:35.840 -> Hit any key to stop autoboot: 2 1 0 07:36:37.867 -> 07:36:37.867 -> NAND read: device 0 offset 0xc80000, size 0xa00000 07:36:37.867 -> 07:36:37.867 -> Reading data from 0xc80000 -- 0% complete. Reading data from 0xc99800 -- 1% complete. Reading data from 0xcb3000 -- 2% complete. Reading data from 0xccc800 -- 3% complete. Reading data from 0xce6000 -- 4% complete. Reading data from 0xcff800 -- 5% complete. Reading data from 0xd19800 -- 6% complete. Reading data from 0xd33000 -- 7% complete. Reading data from 0xd4c800 -- 8% complete. Reading data from 0xd66000 -- 9% complete. Reading data from 0xd7f800 -- 10% complete. Reading data from 0xd99800 -- 11% complete. Reading data from 0xdb3000 -- 12% complete. Reading data from 0xdcc800 -- 13% complete. Reading data from 0xde6000 -- 14% complete. Reading data from 0xdff800 -- 15% complete. Reading data from 0xe19800 -- 16% complete. Reading data from 0xe33000 -- 17% complete. Reading data from 0xe4c800 -- 18% complete. Reading data from 0xe66000 -- 19% complete. Reading data from 0xe7f800 -- 20% complete. Reading data from 0xe99800 -- 21% complete. Reading data from 0xeb3000 -- 22% complete. Reading data from 0xecc800 -- 23% complete. Reading data from 0xee6000 -- 24% complete. Reading data from 0xeff800 -- 25% complete. Reading data from 0xf19800 -- 26% complete. Reading data from 0xf33000 -- 27% complete. Reading data from 0xf4c800 -- 28% complete. Reading data from 0xf66000 -- 29% complete. Reading data from 0xf7f800 -- 30% complete. Reading data from 0xf99800 -- 31% complete. Reading data from 0xfb3000 -- 32% complete. Reading data from 0xfcc800 -- 33% complete. Reading data from 0xfe6000 -- 34% complete. Reading data from 0xfff800 -- 35% complete. Reading data from 0x1019800 -- 36% complete. Reading data from 0x1033000 -- 37% complete. Reading data from 0x104c800 -- 38% complete. Reading data from 0x1066000 -- 39% complete. Reading data from 0x107f800 -- 40% complete. Reading data from 0x1099800 -- 41% complete. Reading data from 0x10b3000 -- 42% complete. Reading data from 0x10cc800 -- 43% complete. Reading data from 0x10e6000 -- 44% complete. Reading data from 0x10ff800 -- 45% complete. Reading data from 0x1119800 -- 46% complete. Reading data from 0x1133000 -- 47% complete. Reading data from 0x114c800 -- 48% complete. Reading data from 0x1166000 -- 49% complete. Reading data from 0x117f800 -- 50% complete. Reading data from 0x1199800 -- 51% complete. Reading data from 0x11b3000 -- 52% complete. Reading data from 0x11cc800 -- 53% complete. Reading data from 0x11e6000 -- 54% complete. Reading data from 0x11ff800 -- 55% complete. Reading data from 0x1219800 -- 56% complete. Reading data from 0x1233000 -- 57% complete. Reading data from 0x124c800 -- 58% complete. Reading data from 0x1266000 -- 59% complete. Reading data from 0x127f800 -- 60% complete. Reading data from 0x1299800 -- 61% complete. Reading data from 0x12b3000 -- 62% complete. Reading data from 0x12cc800 -- 63% complete. Reading data from 0x12e6000 -- 64% complete. Reading data from 0x12ff800 -- 65% complete. Reading data from 0x1319800 -- 66% complete. Reading data from 0x1333000 -- 67% complete. Reading data from 0x134c800 -- 68% complete. Reading data from 0x1366000 -- 69% complete. Reading data from 0x137f800 -- 70% complete. Reading data from 0x1399800 -- 71% complete. Reading data from 0x13b3000 -- 72% complete. Reading data from 0x13cc800 -- 73% complete. Reading data from 0x13e6000 -- 74% complete. Reading data from 0x13ff800 -- 75% complete. Reading data from 0x1419800 -- 76% complete. Reading data from 0x1433000 -- 77% complete. Reading data from 0x144c800 -- 78% complete. Reading data from 0x1466000 -- 79% complete. Reading data from 0x147f800 -- 80% complete. Reading data from 0x1499800 -- 81% complete. Reading data from 0x14b3000 -- 82% complete. Reading data from 0x14cc800 -- 83% complete. Reading data from 0x14e6000 -- 84% complete. Reading data from 0x14ff800 -- 85% complete. Reading data from 0x1519800 -- 86% complete. Reading data from 0x1533000 -- 87% complete. Reading data from 0x154c800 -- 88% complete. Reading data from 0x1566000 -- 89% complete. Reading data from 0x157f800 -- 90% complete. Reading data from 0x1599800 -- 91% complete. Reading data from 0x15b3000 -- 92% complete. Reading data from 0x15cc800 -- 93% complete. Reading data from 0x15e6000 -- 94% complete. Reading data from 0x15ff800 -- 95% complete. Reading data from 0x1619800 -- 96% complete. Reading data from 0x1633000 -- 97% complete. Reading data from 0x164c800 -- 98% complete. Reading data from 0x1666000 -- 99% complete. Reading data from 0x167f800 -- 100% complete. 07:36:44.844 -> 10485760 bytes read: OK 07:36:44.844 -> ## Booting image at 02000000 ... 07:36:44.844 -> Image Name: Linux-2.6.22.18 07:36:44.844 -> Created: 2011-02-22 3:33:51 UTC 07:36:44.844 -> Image Type: ARM Linux Kernel Image (uncompressed) 07:36:44.844 -> Data Size: 5701144 Bytes = 5.4 MB 07:36:44.844 -> Load Address: 00008000 07:36:44.844 -> Entry Point: 00008000 07:36:44.844 -> Verifying Checksum ... OK 07:36:46.207 -> OK 07:36:46.207 -> 07:36:46.207 -> Starting kernel ... 07:36:46.207 -> 07:36:46.207 -> Uncompressing Linux..................................................................................................................................................................................................................................................................... done, booting the kernel. 07:36:46.805 -> Linux version 2.6.22.18 (root@Neo) (gcc version 3.4.3 (MontaVista 3.4.3-25.0.70.0501961 2005-12-18)) #2 Tue Feb 22 11:33:29 CST 2011 07:36:48.267 -> CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977 07:36:48.267 -> Machine: Feroceon-KW 07:36:48.267 -> Using UBoot passing parameters structure 07:36:48.267 -> Memory policy: ECC disabled, Data cache writeback 07:36:48.267 -> CPU0: D VIVT write-back cache 07:36:48.267 -> CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets 07:36:48.267 -> CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets 07:36:48.267 -> Built 1 zonelists. Total pages: 65024 07:36:48.334 -> Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init 07:36:48.334 -> PID hash table entries: 1024 (order: 10, 4096 bytes) 07:36:48.334 -> Console: colour dummy device 80x30 07:36:48.334 -> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) 07:36:48.334 -> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) 07:36:48.334 -> Memory: 256MB 0MB 0MB 0MB = 256MB total 07:36:48.367 -> Memory: 251392KB available (4832K code, 403K data, 3116K init) 07:36:48.367 -> Mount-cache hash table entries: 512 07:36:48.367 -> CPU: Testing write buffer coherency: ok 07:36:48.367 -> NET: Registered protocol family 16 07:36:48.367 -> 07:36:48.367 -> CPU Interface 07:36:48.367 -> ------------- 07:36:48.367 -> SDRAM_CS0 ....base 00000000, size 256MB 07:36:48.367 -> SDRAM_CS1 ....disable 07:36:48.367 -> SDRAM_CS2 ....disable 07:36:48.367 -> SDRAM_CS3 ....disable 07:36:48.367 -> PEX0_MEM ....base e8000000, size 128MB 07:36:48.367 -> PEX0_IO ....base f2000000, size 1MB 07:36:48.367 -> INTER_REGS ....base f1000000, size 1MB 07:36:48.367 -> NFLASH_CS ....base fa000000, size 2MB 07:36:48.400 -> SPI_CS ....base f4000000, size 16MB 07:36:48.400 -> BOOT_ROM_CS ....no such 07:36:48.400 -> DEV_BOOTCS ....no such 07:36:48.400 -> CRYPT_ENG ....base f0000000, size 2MB 07:36:48.400 -> 07:36:48.400 -> Marvell Development Board (LSP Version KW_LSP_4.2.7)-- RD-88F6281A Soc: MV88F6281 Rev 3 LE 07:36:48.400 -> 07:36:48.400 -> Detected Tclk 200000000 and SysClk 400000000 07:36:48.400 -> Marvell USB EHCI Host controller #0: c0a9a600 07:36:48.400 -> PEX0 interface detected Link X1 07:36:48.400 -> PCI: bus0: Fast back to back transfers disabled 07:36:48.400 -> SCSI subsystem initialized 07:36:48.400 -> usbcore: registered new interface driver usbfs 07:36:48.467 -> usbcore: registered new interface driver hub 07:36:48.467 -> usbcore: registered new device driver usb 07:36:48.467 -> NET: Registered protocol family 2 07:36:48.467 -> Time: kw_clocksource clocksource has been installed. 07:36:48.467 -> IP route cache hash table entries: 2048 (order: 1, 8192 bytes) 07:36:48.467 -> TCP established hash table entries: 8192 (order: 4, 65536 bytes) 07:36:48.467 -> TCP bind hash table entries: 8192 (order: 3, 32768 bytes) 07:36:48.467 -> TCP: Hash tables configured (established 8192 bind 8192) 07:36:48.467 -> TCP reno registered 07:36:48.467 -> RTC registered 07:36:48.467 -> Use the XOR engines (acceleration) for enhancing the following functions: 07:36:48.500 -> o RAID 5 Xor calculation 07:36:48.500 -> o kernel memcpy 07:36:48.500 -> o kenrel memzero 07:36:48.500 -> Number of XOR engines to use: 4 07:36:48.500 -> cesadev_init(c0011f5c) 07:36:48.500 -> mvCesaInit: sessions=640, queue=64, pSram=f0000000 07:36:48.500 -> Warning: TS unit is powered off. 07:36:48.500 -> gpio_dev = fe00000 07:36:48.500 -> LED_SET_CTL_IOC_NUM= 6702 07:36:48.500 -> High gpio polarity = 50 07:36:48.500 -> High gpio polarity = 70 07:36:48.500 -> Enable Interrupt 07:36:48.500 -> mv88f6281_wdt: Watchdog Timer timeout = 8 sec. 07:36:48.500 -> mv88f6281_wdt: HW Watchdog timeout = 15 sec. 07:36:48.500 -> VFS: Disk quotas dquot_6.5.1 07:36:48.533 -> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) 07:36:48.533 -> Installing knfsd (copyright (C) 1996 okir@monad.swb.de). 07:36:48.533 -> JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. 07:36:48.533 -> fuse init (API version 7.8) 07:36:48.533 -> SGI XFS with large block numbers, no debug enabled 07:36:48.533 -> SGI XFS Quota Management subsystem 07:36:48.533 -> yaffs Feb 10 2011 21:07:53 Installing. 07:36:48.533 -> io scheduler noop registered 07:36:48.533 -> io scheduler cfq registered (default) 07:36:48.533 -> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled 07:36:48.533 -> serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A 07:36:48.600 -> serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A 07:36:48.600 -> RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize 07:36:48.600 -> loop: module loaded 07:36:48.600 -> Loading Marvell Ethernet Driver: 07:36:48.600 -> o Cached descriptors in DRAM 07:36:48.600 -> o DRAM SW cache-coherency 07:36:48.600 -> o Single RX Queue support - ETH_DEF_RXQ=0 07:36:48.600 -> o Single TX Queue support - ETH_DEF_TXQ=0 07:36:48.600 -> o TCP segmentation offload enabled 07:36:48.600 -> o Receive checksum offload enabled 07:36:48.600 -> o Transmit checksum offload enabled 07:36:48.633 -> o Network Fast Processing (Routing) supported 07:36:48.633 -> o Proc tool API enabled 07:36:48.633 -> o Rx descripors: q0=128 07:36:48.633 -> o Tx descripors: q0=532 07:36:48.633 -> o Loading network interface(s): 07:36:48.633 -> eth_get_config: Unexpected port number 0 07:36:48.633 -> EthPort #0: Bad initialization parameters 07:36:48.633 -> eth port=0: load failed 07:36:48.633 -> eth_init_module: can't init eth_hal driver 07:36:48.633 -> Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI 07:36:48.633 -> Copyright (c) 1999-2006 Intel Corporation. 07:36:48.633 -> e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI 07:36:48.633 -> e100: Copyright(c) 1999-2006 Intel Corporation 07:36:48.666 -> Integrated Sata device found 07:36:53.651 -> scsi0 : Marvell SCSI to SATA adapter 07:36:53.684 -> scsi1 : Marvell SCSI to SATA adapter 07:36:54.215 -> scsi 0:0:0:0: Direct-Access WDC WD5000AAKX-001CA 15.0 PQ: 0 ANSI: 5 07:36:54.248 -> EnablePowerSaving 07:36:54.248 -> PowerSavingTime = 15 07:36:54.248 -> /////////////////////////////////// init sd 07:36:54.248 -> sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) 07:36:54.248 -> sd 0:0:0:0: [sda] Write Protect is off 07:36:54.248 -> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA 07:36:54.248 -> sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) 07:36:54.248 -> sd 0:0:0:0: [sda] Write Protect is off 07:36:54.248 -> sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA 07:36:54.315 -> sda: sda1 sda2 07:36:54.315 -> sd 0:0:0:0: [sda] Attached SCSI disk 07:36:54.315 -> sd 0:0:0:0: Attached scsi generic sg0 type 0 07:36:54.315 -> NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ 07:36:54.315 -> NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit) 07:36:54.315 -> Scanning device for bad blocks 07:36:54.315 -> Bad eraseblock 76 at 0x00980000 07:36:54.315 -> Bad eraseblock 281 at 0x02320000 07:36:54.315 -> Bad eraseblock 494 at 0x03dc0000 07:36:54.348 -> Bad eraseblock 703 at 0x057e0000 07:36:54.415 -> 9 cmdlinepart partitions found on MTD device nand_mtd 07:36:54.415 -> Using command line partition definition 07:36:54.415 -> Creating 9 MTD partitions on "nand_mtd": 07:36:54.415 -> 0x00000000-0x00100000 : "uboot" 07:36:54.415 -> 0x00100000-0x00180000 : "uboot_env" 07:36:54.415 -> 0x00180000-0x00200000 : "key_store" 07:36:54.415 -> 0x00200000-0x00280000 : "info" 07:36:54.415 -> 0x00280000-0x00c80000 : "etc" 07:36:54.415 -> 0x00c80000-0x01680000 : "kernel_1" 07:36:54.415 -> 0x01680000-0x04640000 : "rootfs1" 07:36:54.415 -> 0x04640000-0x05040000 : "kernel_2" 07:36:54.415 -> 0x05040000-0x08000000 : "rootfs2" 07:36:54.415 -> ehci_marvell ehci_marvell.70059: Marvell Orion EHCI 07:36:54.448 -> ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 07:36:54.448 -> ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 07:36:54.482 -> ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 07:36:54.482 -> usb usb1: configuration #1 chosen from 1 choice 07:36:54.482 -> hub 1-0:1.0: USB hub found 07:36:54.482 -> hub 1-0:1.0: 1 port detected 07:36:54.582 -> USB Universal Host Controller Interface driver v3.0 07:36:54.880 -> usb 1-1: new high speed USB device using ehci_marvell and address 2 07:36:55.047 -> In hub_port_init, and number is 0, retry 0, port 1 ..... 07:36:55.047 -> usb 1-1: configuration #1 chosen from 1 choice 07:36:55.047 -> hub 1-1:1.0: USB hub found 07:36:55.047 -> hub 1-1:1.0: 4 ports detected 07:36:55.146 -> usbcore: registered new interface driver usblp 07:36:55.180 -> drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver 07:36:55.180 -> Initializing USB Mass Storage driver... 07:36:55.180 -> usbcore: registered new interface driver usb-storage 07:36:55.180 -> USB Mass Storage support registered. 07:36:55.180 -> mice: PS/2 mouse device common for all mice 07:36:55.180 -> i2c /dev entries driver 07:36:55.180 -> i2c-adapter i2c-0: Unrecognized version/stepping 0x69 Defaulting to Generic LM85. 07:36:55.180 -> hwmon-vid: Unknown VRM version of your CPU 07:36:55.180 -> md: linear personality registered for level -1 07:36:55.180 -> md: raid0 personality registered for level 0 07:36:55.213 -> md: raid1 personality registered for level 1 07:36:55.379 -> raid6: int32x1 95 MB/s 07:36:55.512 -> raid6: int32x2 138 MB/s 07:36:55.711 -> raid6: int32x4 125 MB/s 07:36:55.910 -> raid6: int32x8 111 MB/s 07:36:55.910 -> raid6: using algorithm int32x2 (138 MB/s) 07:36:55.910 -> md: raid6 personality registered for level 6 07:36:55.910 -> md: raid5 personality registered for level 5 07:36:55.910 -> md: raid4 personality registered for level 4 07:36:55.910 -> raid5: measuring checksumming speed 07:36:55.943 -> arm4regs : 1090.800 MB/sec 07:36:55.977 -> 8regs : 653.600 MB/sec 07:36:56.076 -> 32regs : 884.400 MB/sec 07:36:56.076 -> raid5: using function: arm4regs (1090.800 MB/sec) 07:36:56.076 -> device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com 07:36:56.076 -> usbcore: registered new interface driver hiddev 07:36:56.076 -> usbcore: registered new interface driver usbhid 07:36:56.076 -> drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver 07:36:56.076 -> TCP cubic registered 07:36:56.076 -> NET: Registered protocol family 1 07:36:56.076 -> NET: Registered protocol family 17 07:36:56.076 -> Freeing init memory: 3116K 07:36:56.142 -> [031m*** Stage 1: Setup system and device drivers ***[0m 07:36:56.575 -> r8168 Gigabit Ethernet driver 8.012.00-NAPI loaded 07:36:56.641 -> pci_resource_start(pdev, 2) = e8014000 07:36:56.641 -> r8168 0000:00:01.0: no MSI. Back to INTx. 07:36:56.641 -> Set LED ... 07:36:56.641 -> r8168: This product is covered by one or more of the following patents: US5,307,459, US5,434,872, US5,732,094, US6,570,884, US6,115,776, and US6,327,625. 07:36:56.641 -> eth0: RTL8168B/8111B at 0xd0854000, 00:00:00:00:00:30, IRQ 9 07:36:56.641 -> ioaddr = d0854000 07:36:56.708 -> r8168 Copyright (C) 2009 Realtek NIC software team <nicfae@realtek.com> 07:36:56.708 -> This program comes with ABSOLUTELY NO WARRANTY; for details, please see http://www.gnu.org/licenses/. 07:36:56.708 -> This is free software, and you are welcome to redistribute it under certain conditions; see http://www.gnu.org/licenses/. 07:36:56.774 -> r8168: egiga0: link down 07:36:56.807 -> hwclock: settimeofday() failed: Invalid argument 07:36:57.007 -> [031m*** Stage 2: Prepare the root file system ***[0m 07:36:57.040 -> [033mMount system partition...[0m 07:36:57.040 -> yaffs: dev is 32505862 name is "mtdblock6" 07:36:57.040 -> yaffs: passed flags "" 07:36:57.040 -> yaffs: Attempting MTD mount on 31.6, "mtdblock6" 07:36:57.073 -> block 102 is bad 07:36:57.073 -> block 315 is bad 07:36:57.904 -> yaffs_read_super: isCheckpointed 0 07:36:58.004 -> e2fsck 1.38 (30-Jun-2005) 07:36:58.037 -> /dev/sda1: clean, 13/128520 files, 506601/514048 blocks 07:36:58.037 -> kjournald starting. Commit interval 5 seconds 07:36:58.037 -> EXT3-fs: mounted filesystem with ordered data mode. 07:36:58.137 -> kjournald starting. Commit interval 5 seconds 07:36:58.137 -> EXT3-fs: mounted filesystem with ordered data mode. 07:36:58.170 -> /dev/sda1 /zyxel/mnt/sysdisk ext3 ro,data=ordered 0 0 07:36:58.170 -> 0 07:36:58.170 -> Boot from disk 07:36:59.998 -> Checksum of sysdisk.img : 7ddf39bd27e18147c31a7d325e5acc98 07:36:59.998 -> Checksum from INFO : 7ddf39bd27e18147c31a7d325e5acc98 07:36:59.998 -> Checksum pass! 07:36:59.998 -> [033mMount system disk image ...[0m 07:37:00.030 -> cp: /ram_bin/bin/*: No such file or directory 07:37:00.097 -> yaffs: dev is 32505860 name is "mtdblock4" 07:37:00.130 -> yaffs: passed flags "" 07:37:00.130 -> yaffs: Attempting MTD mount on 31.4, "mtdblock4" 07:37:00.130 -> yaffs: restored from checkpoint 07:37:00.130 -> yaffs_read_super: isCheckpointed 1 07:37:00.163 -> /etc/zyxel/conf exist.. 07:37:00.230 -> [031m*** Stage 3: Start services on HDD ***[0m 07:37:00.263 -> NTFS driver 2.1.28 [Flags: R/O MODULE]. 07:37:00.297 -> tntfs: module license 'Commercial. For support email tntfs-support@tuxera.com.' taints kernel. 07:37:00.297 -> Tuxera NTFS driver 3010.9.16 [Flags: R/W MODULE]. 07:37:00.330 -> modprobe: module fuse not found. 07:37:00.330 -> modprobe: failed to load module fuse 07:37:00.430 -> Starting PID Fan Control.. 07:37:00.430 -> P:20, I:1, D:5, SampleRate:10 seconds, ST_CPU:46, ST_ADT7463:46, ST_DauBoard:46 07:37:00.430 -> Wt_CPU:0, Wt_ADT7463:0, Wt_DauBoard:1 07:37:00.430 -> Tolerance:1 MinPwm:0x40 07:37:00.430 -> 07:37:03.452 -> sda 07:37:03.452 -> checking sda 07:37:03.518 -> Trying to mount /dev/sda1 07:37:03.551 -> mount: /dev/sda1 already mounted or /mnt/parnerkey busy 07:37:03.551 -> mount: according to mtab, /dev/sda1 is mounted on /zyxel/mnt/sysdisk 07:37:03.551 -> Fail to mount /dev/sda1 07:37:03.551 -> Press ENTER to continue... 07:37:03.551 -> Starting zylogd... 07:37:03.584 -> zylog starts. 07:37:03.584 -> Starting uamd... 07:37:13.715 -> Starting ZySH daemon and client... 07:37:13.715 -> Start NSA-220 system daemon.... 07:37:13.715 -> Start ZySH daemon 07:37:13.782 -> zyshd: version 2.0.0 (build: 18:01:49 Feb 9 2011) 07:37:13.782 -> % zylog init start 07:37:13.782 -> cat: /var/run/syslog-ng.pid: No such file or directory 07:37:13.782 -> Try to KILL SIGHUP to syslog-ng: pid=0 07:37:13.782 -> syslog-ng not running, start /usr/sbin/syslog-ng 07:37:13.815 -> Dec 29 00:31:00 (none) syslog-ng[1110]: syslog-ng starting up; version='2.0.10' 07:37:13.848 -> zyio_open_config success. (/etc/__system_default.xml, 0) 07:37:13.848 -> zyio_open_config success. (/etc/zyxel/conf/__system_default_device_ha.xml, 0) 07:37:13.848 -> /usr/sbin/zic -d /etc /var/zyxel/myzone_rule 07:37:13.848 -> /bin/ln -s -f /etc/MyZone /etc/localtime 07:37:13.848 -> /bin/hostname HomeDisk 07:37:13.914 -> Usage: umount [-hV] 07:37:13.914 -> umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts] 07:37:13.914 -> umount [-f] [-F] [-r] [-n] [-v] special | node... 07:37:13.948 -> Usage: umount [-hV] 07:37:13.948 -> umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts] 07:37:13.948 -> umount [-f] [-F] [-r] [-n] [-v] special | node... 07:37:13.981 -> BusyBox v1.1.1 (2011.01.26-03:51+0000) multi-call binary 07:37:13.981 -> 07:37:13.981 -> Usage: rmdir [OPTION]... DIRECTORY... 07:37:13.981 -> 07:37:13.981 -> sh: cannot create /i-data/.zyxel/close_ftp_mapping: Directory nonexistent 07:37:14.977 -> Init SMB DB access... 07:37:15.011 -> rm: cannot remove `/var/log/samba/smb.db': No such file or directory 07:37:16.074 -> zyio_container_create_template(/etc/__system_default.xml): scope:[network/wlan] list:[wlan_list] type:[wlan_t] is not existed 07:37:18.897 -> Assemble volume.... 07:37:18.930 -> [1153] server write-only FIFO is opened (fd=6) 07:37:18.930 -> [1153] server read-only FIFO is opened (fd=7) 07:37:18.930 -> [1153] server error read-only FIFO is opened (fd=8) 07:37:18.930 -> argc = 1, func = 277 07:37:19.096 -> md: md0 stopped. 07:37:19.096 -> md: bind<sda2> 07:37:19.129 -> cat: /tmp/mduuid.map: No such file or directory 07:37:19.163 -> Filesystem "md0": Disabling barriers, not supported by the underlying device 07:37:19.196 -> XFS mounting filesystem md0 07:37:19.429 -> Startup config 07:37:19.462 -> POLLHUP on 7 07:37:19.462 -> pid = 1153 07:37:19.462 -> [1153] is disconnected 07:37:19.462 -> [1205] server write-only FIFO is opened (fd=6) 07:37:19.462 -> [1205] server read-only FIFO is opened (fd=7) 07:37:19.462 -> [1205] server error read-only FIFO is opened (fd=8) 07:37:19.462 -> argc = 1, func = 14 07:37:19.462 -> argc = 1, func = 17 07:37:19.462 -> argc = 1, func = 650 07:37:19.528 -> argc = 2, func = 104 07:37:19.528 -> argid[1]: 1069; argv[1]: ge1 07:37:19.528 -> argc = 6, func = 108 07:37:19.528 -> argid[1]: 1069; argv[1]: ge1 07:37:19.528 -> argid[2]: 313; argv[2]: ip 07:37:19.528 -> argid[3]: 434; argv[3]: address 07:37:19.528 -> argid[4]: 1062; argv[4]: 192.168.1.5 07:37:19.528 -> argid[5]: 1062; argv[5]: 255.255.255.0 07:37:19.528 -> argc = 5, func = 109 07:37:19.528 -> argid[1]: 1069; argv[1]: ge1 07:37:19.528 -> argid[2]: 313; argv[2]: ip 07:37:19.528 -> argid[3]: 542; argv[3]: gateway 07:37:19.528 -> argid[4]: 1062; argv[4]: 192.168.1.1 07:37:19.528 -> argc = 4, func = 106 07:37:19.528 -> argid[1]: 1069; argv[1]: ge1 07:37:19.528 -> argid[2]: 540; argv[2]: mtu 07:37:19.528 -> argid[3]: 1386; argv[3]: 1500 07:37:19.561 -> argc = 3, func = 105 07:37:19.561 -> argid[1]: 1069; argv[1]: ge1 07:37:19.561 -> argid[2]: 350; argv[2]: exit 07:37:19.561 -> argc = 2, func = 427 07:37:19.561 -> argid[1]: 1062; argv[1]: 192.168.1.1 07:37:19.561 -> argc = 4, func = 429 07:37:19.561 -> argid[1]: 867; argv[1]: fetch 07:37:19.561 -> argid[2]: 868; argv[2]: manually 07:37:19.561 -> argid[3]: 1069; argv[3]: ge1 07:37:21.587 -> /bin/rm -f /var/zyxel/zysh/egiga0.metric 07:37:21.587 -> argc = 7, func = 77 07:37:21.587 -> argid[1]: 267; argv[1]: mail 07:37:21.587 -> argid[2]: 1379; argv[2]: 1 07:37:21.587 -> argid[3]: 435; argv[3]: category 07:37:21.587 -> argid[4]: 375; argv[4]: all 07:37:21.587 -> argid[5]: 461; argv[5]: level 07:37:21.587 -> argid[6]: 478; argv[6]: alert 07:37:21.587 -> mail server '1' log_category(all) is:alert 07:37:21.587 -> argc = 7, func = 77 07:37:21.587 -> argid[1]: 267; argv[1]: mail 07:37:21.587 -> argid[2]: 1379; argv[2]: 1 07:37:21.587 -> argid[3]: 435; argv[3]: category 07:37:21.587 -> argid[4]: 375; argv[4]: all 07:37:21.587 -> argid[5]: 461; argv[5]: level 07:37:21.587 -> argid[6]: 375; argv[6]: all 07:37:21.587 -> mail server '1' log_category(all) is:all 07:37:21.620 -> argc = 2, func = 68 07:37:21.620 -> argid[1]: 1061; argv[1]: ntp1.tele.dk 07:37:21.620 -> argc = 2, func = 60 07:37:21.620 -> argid[1]: 1112; argv[1]: +0100 07:37:21.620 -> /usr/sbin/zic -d /etc /var/zyxel/myzone_rule 07:37:21.620 -> /bin/ln -s -f /etc/MyZone /etc/localtime 07:37:21.620 -> argc = 1, func = 72 07:37:21.620 -> /usr/sbin/ntpdate_agent ntp1.tele.dk 07:37:21.620 -> argc = 4, func = 343 07:37:21.620 -> argid[1]: 1205; argv[1]: "CET" 07:37:21.620 -> argid[2]: 593; argv[2]: in 07:37:21.620 -> argid[3]: 1206; argv[3]: "Brussels,Copenhagen,Madrid,Paris" 07:37:21.687 -> argc = 2, func = 192 07:37:21.687 -> argid[1]: 1122; argv[1]: "admin" 07:37:21.753 -> argc = 5, func = 193 07:37:21.753 -> argid[1]: 1122; argv[1]: "admin" 07:37:21.753 -> argid[2]: 1390; argv[2]: 501 07:37:21.753 -> argid[3]: 363; argv[3]: password 07:37:21.753 -> argid[4]: 1145; argv[4]: A3D1E87994E85270C482C03F54CDB5D9:F9F5B7CD7933221687A0AAA18F67C9A9 07:37:21.886 -> enter smb_db_update_user 07:37:21.886 -> argc = 5, func = 193 07:37:21.919 -> argid[1]: 1122; argv[1]: "admin" 07:37:21.919 -> argid[2]: 1390; argv[2]: 501 07:37:21.919 -> argid[3]: 633; argv[3]: type 07:37:21.919 -> argid[4]: 634; argv[4]: admin 07:37:21.919 -> enter smb_db_update_user 07:37:21.919 -> argc = 5, func = 194 07:37:21.919 -> argid[1]: 1122; argv[1]: "admin" 07:37:21.919 -> argid[2]: 1390; argv[2]: 501 07:37:21.919 -> argid[3]: 638; argv[3]: shpass 07:37:21.919 -> argid[4]: 1148; argv[4]: $1$$O50.7sajoawk19kwSgxsz0 07:37:21.919 -> shpass : $1$$O50.7sajoawk19kwSgxsz0 07:37:21.919 -> argc = 4, func = 189 07:37:21.919 -> argid[1]: 1122; argv[1]: "admin" 07:37:21.919 -> argid[2]: 1390; argv[2]: 501 07:37:21.919 -> argid[3]: 350; argv[3]: exit 07:37:21.919 -> argc = 6, func = 174 07:37:21.952 -> argid[1]: 456; argv[1]: share 07:37:21.952 -> argid[2]: 626; argv[2]: save 07:37:21.952 -> argid[3]: 1150; argv[3]: "HomeDisk" 07:37:21.952 -> argid[4]: 395; argv[4]: path 07:37:21.952 -> argid[5]: 1152; argv[5]: "/i-data/md0/HomeDisk" 07:37:21.952 -> argc = 7, func = 175 07:37:21.952 -> argid[1]: 456; argv[1]: share 07:37:21.952 -> argid[2]: 626; argv[2]: save 07:37:21.952 -> argid[3]: 1150; argv[3]: "HomeDisk" 07:37:21.952 -> argid[4]: 395; argv[4]: path 07:37:21.952 -> argid[5]: 1152; argv[5]: "/i-data/md0/HomeDisk" 07:37:21.952 -> argid[6]: 612; argv[6]: media-server 07:37:21.952 -> argc = 7, func = 163 07:37:21.952 -> argid[1]: 456; argv[1]: share 07:37:21.952 -> argid[2]: 626; argv[2]: save 07:37:22.018 -> argid[3]: 1150; argv[3]: "HomeDisk" 07:37:22.018 -> argid[4]: 395; argv[4]: path 07:37:22.018 -> argid[5]: 1152; argv[5]: "/i-data/md0/HomeDisk" 07:37:22.018 -> argid[6]: 350; argv[6]: exit 07:37:22.018 -> RegenSmbConfigFile:2114 Close file ok 07:37:22.018 -> argc = 6, func = 174 07:37:22.018 -> argid[1]: 456; argv[1]: share 07:37:22.018 -> argid[2]: 626; argv[2]: save 07:37:22.018 -> argid[3]: 1150; argv[3]: "admin" 07:37:22.018 -> argid[4]: 395; argv[4]: path 07:37:22.018 -> argid[5]: 1152; argv[5]: "/i-data/md0/admin" 07:37:22.018 -> argc = 7, func = 163 07:37:22.018 -> argid[1]: 456; argv[1]: share 07:37:22.018 -> argid[2]: 626; argv[2]: save 07:37:22.018 -> argid[3]: 1150; argv[3]: "admin" 07:37:22.052 -> argid[4]: 395; argv[4]: path 07:37:22.052 -> argid[5]: 1152; argv[5]: "/i-data/md0/admin" 07:37:22.052 -> argid[6]: 350; argv[6]: exit 07:37:22.052 -> RegenSmbConfigFile:2114 Close file ok 07:37:22.052 -> argc = 2, func = 399 07:37:22.052 -> argid[1]: 1219; argv[1]: default 07:37:22.218 -> argc = 2, func = 396 07:37:22.218 -> argid[1]: 1226; argv[1]: yes 07:37:22.218 -> argc = 1, func = 519 07:37:22.549 -> Jan 1 00:59:59 (none) mt-daapd[1335]: Starting rendezvous daemon 07:37:22.616 -> Jan 1 00:59:59 (none) mt-daapd[1339]: Starting signal handler 07:37:23.612 -> Jan 1 00:59:59 (none) mt-daapd[1339]: Loading playlists 07:37:23.678 -> Jan 1 00:59:59 (none) mt-daapd[1339]: Initializing database 07:37:23.678 -> Jan 1 00:59:59 (none) mt-daapd[1339]: Starting mp3 scan 07:37:23.678 -> Jan 1 00:59:59 (none) mt-daapd[1339]: Starting web server from /usr/local/apache/htdocs/zyxel on port 3689 07:37:23.678 -> Jan 1 00:59:59 (none) mt-daapd[1339]: Registering rendezvous names 07:37:23.678 -> Jan 1 00:59:59 (none) mt-daapd[1339]: Scanned 0 songs in 1 seconds 07:37:24.509 -> Starting iTune SDisablePowerSaving 07:37:24.509 -> erver: 07:37:24.509 -> CheckTimerState = 1 07:37:24.575 -> /i-data/md0/.zyEnablePowerSaving 07:37:24.575 -> xel existing: /iPowerSavingTime = 15 07:37:24.575 -> -data/md0/.zyxel exist 07:37:24.575 -> iTunes starting OK 07:37:24.575 -> Successfully starting iTunes server! 07:37:24.575 -> argc = 2, func = 146 07:37:24.575 -> argid[1]: 1137; argv[1]: 15 07:37:24.575 -> test0 07:37:24.575 -> Test1 07:37:24.575 -> Test2 07:37:24.575 -> Test3: 07:37:24.575 -> argc = 5, func = 168 07:37:24.575 -> argid[1]: 456; argv[1]: share 07:37:24.575 -> argid[2]: 615; argv[2]: recycle-bin 07:37:24.575 -> argid[3]: 620; argv[3]: expireday 07:37:24.575 -> argid[4]: 1389; argv[4]: 45 07:37:24.575 -> argc = 2, func = 160 07:37:24.575 -> argid[1]: 1142; argv[1]: d 07:37:24.575 -> exec_cmd complete 07:37:24.575 -> eth status = Wake-onpumbg 07:37:24.608 -> ethtest0 07:37:24.608 -> Test1 07:37:24.608 -> Test2 07:37:24.608 -> Test3: 07:37:24.608 -> eth cmd = /sbin/ethtool -s egiga0 wol d 07:37:24.608 -> argc = 2, func = 18 07:37:24.608 -> argid[1]: 350; argv[1]: exit 07:37:24.608 -> argc = 1, func = 20 07:37:24.608 -> POLLHUP on 7 07:37:24.608 -> pid = 1205 07:37:24.608 -> [1205] is disconnected 07:37:24.608 -> TDC Style Detected, overwrite admin's password 07:37:24.674 -> [1407] server write-only FIFO is opened (fd=6) 07:37:24.674 -> [1407] server read-only FIFO is opened (fd=7) 07:37:24.674 -> [1407] server error read-only FIFO is opened (fd=8) 07:37:24.674 -> argc = 6, func = 190 07:37:24.674 -> argid[1]: 363; argv[1]: password 07:37:24.674 -> argid[2]: 616; argv[2]: modify 07:37:24.674 -> argid[3]: 1122; argv[3]: "admin" 07:37:24.674 -> argid[4]: 1144; argv[4]: "33D67NTk" 07:37:24.674 -> argid[5]: 1143; argv[5]: RaidLing 07:37:24.774 -> enter smb_db_update_user 07:37:24.808 -> POLLHUP on 7 07:37:24.808 -> pid = 1407 07:37:24.808 -> [1407] is disconnected 07:37:24.841 -> ---> Starting upgrade_firmware.sh at 1920-12-29 01:31:11 07:37:24.907 -> ---> Starting upgrade_firmware.sh at 1920-12-29 01:31:11 07:37:24.907 -> cat: /tmp/fwupgrade/fwlog: No such file or directory 07:37:24.907 -> [: -1: unknown operand 07:37:24.907 -> rm: cannot remove `/i-data/.zyxel/zyfw/zyfw_info': No such file or directory 07:37:24.907 -> rm: cannot remove `/tmp/zyfw_info': No such file or directory 07:37:24.907 -> ---> download firmware information 07:37:24.907 -> rm: cannot remove `/tmp/zyfw_dl_errno': No such file or directory 07:37:24.907 -> [1441] server write-only FIFO is opened (fd=6) 07:37:24.940 -> [1441] server read-only FIFO is opened (fd=7) 07:37:24.940 -> [1441] server error read-only FIFO is opened (fd=8) 07:37:24.940 -> argc = 2, func = 637 07:37:24.940 -> argid[1]: 1343; argv[1]: 1 07:37:24.940 -> Result: Download 07:37:24.940 -> LastUpdated: N/A 07:37:24.940 -> Model: N/A 07:37:24.940 -> FW file: N/A 07:37:24.940 -> FW version: N/A 07:37:24.940 -> Revision: N/A 07:37:24.940 -> Release date: N/A 07:37:24.940 -> Release note: N/A 07:37:24.940 -> Size: N/A 07:37:24.940 -> Checksum: N/A 07:37:24.940 -> POLLHUP on 7 07:37:24.940 -> pid = 1441 07:37:24.940 -> [1441] is disconnected 07:37:24.940 -> ---> make sure process to download fwInfo is finished 07:37:25.007 -> du: /i-data/md0/.zyxel/clidump.gui: No such file or directory 07:37:25.007 -> [: 10240: unknown operand 07:37:25.073 -> du: /i-data/.zyxel/twonkymedia.log: No such file or directory 07:37:25.107 -> [: 10240: unknown operand 07:37:25.107 -> du: /i-data/.zyxel/cdsdaemon.log: No such file or directory 07:37:25.107 -> [: 10240: unknown operand 07:37:25.107 -> configure terminal ip smb internal enable "/i-data/md0" 07:37:25.140 -> [1490] server write-only FIFO is opened (fd=6) 07:37:25.173 -> [1490] server read-only FIFO is opened (fd=7) 07:37:25.173 -> [1490] server error read-only FIFO is opened (fd=8) 07:37:25.173 -> argc = 4, func = 180 07:37:25.173 -> argid[1]: 630; argv[1]: internal 07:37:25.173 -> argid[2]: 302; argv[2]: enable 07:37:25.173 -> argid[3]: 1164; argv[3]: "/i-data/md0" 07:37:25.173 -> RegenSmbConfigFile:2114 Close file ok 07:37:25.173 -> POLLHUP on 7 07:37:25.173 -> pid = 1490 07:37:25.173 -> [1490] is disconnected 07:37:25.173 -> Starting smbd... 07:37:25.306 -> Starting nmbd... 07:37:25.472 -> readlink: /i-data/md1: No such file or directory 07:37:25.472 -> configure terminal ip smb internal disable "/i-data/md1" 07:37:25.472 -> [1501] server write-only FIFO is opened (fd=6) 07:37:25.539 -> [1501] server read-only FIFO is opened (fd=7) 07:37:25.539 -> [1501] server error read-only FIFO is opened (fd=8) 07:37:25.539 -> argc = 4, func = 181 07:37:25.539 -> argid[1]: 630; argv[1]: internal 07:37:25.539 -> argid[2]: 303; argv[2]: disable 07:37:25.539 -> argid[3]: 1164; argv[3]: "/i-data/md1" 07:37:25.539 -> RegenSmbConfigFile:2114 Close file ok 07:37:25.539 -> POLLHUP on 7 07:37:25.539 -> pid = 1501 07:37:25.539 -> [1501] is disconnected 07:37:25.539 -> configure terminal ip smb internal enable "/i-data/3c7e9e7c" 07:37:25.539 -> [1509] server write-only FIFO is opened (fd=6) 07:37:25.572 -> [1509] server read-only FIFO is opened (fd=7) 07:37:25.572 -> [1509] server error read-only FIFO is opened (fd=8) 07:37:25.572 -> argc = 4, func = 180 07:37:25.572 -> argid[1]: 630; argv[1]: internal 07:37:25.572 -> argid[2]: 302; argv[2]: enable 07:37:25.572 -> argid[3]: 1164; argv[3]: "/i-data/3c7e9e7c" 07:37:25.572 -> RegenSmbConfigFile:2114 Close file ok 07:37:25.572 -> POLLHUP on 7 07:37:25.572 -> pid = 1509 07:37:25.572 -> [1509] is disconnected 07:37:25.638 -> Starting crond ... 07:37:26.136 -> Adding 524280k swap on /i-data/.zyxel/swap_ul6545p. Priority:-1 extents:1 across:524280k 07:37:26.170 -> 1442 root 1740 S < /bin/zyfw_downloader http://firmware.tdconline.dk/NSA 07:37:26.170 -> ---> still downloading, wait 2 second 07:37:26.170 -> storage_gen_swap.sh:/zyxel/mnt/sysdisk/swap_ul6545p exists 07:37:26.203 -> GMT offset=3600s 07:37:26.203 -> setting system time zone to tz_minuteswest=-60 07:37:26.336 -> [1613] server write-only FIFO is opened (fd=6) 07:37:26.336 -> [1613] server read-only FIFO is opened (fd=7) 07:37:26.336 -> [1613] server error read-only FIFO is opened (fd=8) 07:37:26.369 -> argc = 2, func = 348 07:37:26.369 -> argid[1]: 1207; argv[1]: former 07:37:26.369 -> POLLHUP on 7 07:37:26.369 -> pid = 1613 07:37:26.369 -> [1613] is disconnected 07:37:26.535 -> Dec 29 01:31:13 (none) syslog-ng[1110]: Termination requested via signal, terminating; 07:37:26.535 -> Dec 29 01:31:13 (none) syslog-ng[1110]: syslog-ng shutting down; version='2.0.10' 07:37:26.535 -> killall: webdisk_hook: no process killed 07:37:26.967 -> /usr/python-2.6.2/lib/python2.6/site-packages/flickrapi/__init__.py:45: DeprecationWarning: the md5 module is deprecated; use hashlib instead 07:37:27.531 -> killall: webdisk_hook: no process killed 07:37:27.597 -> Dec 29 01:31:14 HomeDisk syslog-ng[1649]: syslog-ng starting up; version='2.0.10' 07:37:28.229 -> 1442 root 1740 S < /bin/zyfw_downloader http://firmware.tdconline.dk/NSA 07:37:28.229 -> ---> still downloading, wait 2 second 07:37:28.627 -> [webdisk.h]init_backup_db(509): CREATE TABLE IF NOT EXISTS backup ( seq_num INTEGER PRIMARY KEY, action TEXT, old_name TEXT, old_parent TEXT, old_path TEXT, new_name TEXT, new_parent TEXT, new_path TEXT, type TEXT, size INTEGER, m_date INTEGER, d_date INTEGER, fsync INTEGER, flocalD INTEGER, fremoteD INTEGER, errCount INTEGER, w_name TEXT, w_parent TEXT, w_path TEXT, file_id INTEGER, id_parent INTEGER, checksum TEXT); 07:37:28.660 -> [webdisk.h]init_backup_db(517): CREATE INDEX IF NOT EXISTS seq_num on backup (seq_num); 07:37:28.660 -> [webdisk_maintain.c]main(834): delete from backup where d_date < -1551742125 and fsync=1 and flocalD=1 and fremoteD=1 07:37:28.693 -> [webdisk_maintain.c]main(843): vacuum backup 07:37:30.154 -> Starting Web Server... 07:37:30.254 -> 1442 root 1740 S < /bin/zyfw_downloader http://firmware.tdconline.dk/NSA 07:37:30.254 -> ---> still downloading, wait 2 second 07:37:31.350 -> Jan 1 00:59:59 HomeDisk httpd[1720]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache] 07:37:31.350 -> Jan 1 00:59:59 HomeDisk httpd[1720]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?) 07:37:31.350 -> Jan 1 00:59:59 HomeDisk httpd[1720]: [warn] RSA server certificate CommonName (CN) `HomeDisk' does NOT match server name!? 07:37:31.350 -> Jan 1 00:59:59 HomeDisk httpd[1720]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?) 07:37:31.350 -> Jan 1 00:59:59 HomeDisk httpd[1720]: [warn] RSA server certificate CommonName (CN) `HomeDisk' does NOT match server name!? 07:37:31.350 -> Jan 1 00:59:59 HomeDisk httpd[1720]: [error] mod_auth_zyxel: initialized. 07:37:31.682 -> Jan 1 00:59:59 HomeDisk httpd[1729]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?) 07:37:31.715 -> Jan 1 00:59:59 HomeDisk httpd[1729]: [warn] RSA server certificate CommonName (CN) `HomeDisk' does NOT match server name!? 07:37:31.715 -> Jan 1 00:59:59 HomeDisk httpd[1729]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?) 07:37:31.715 -> Jan 1 00:59:59 HomeDisk httpd[1729]: [warn] RSA server certificate CommonName (CN) `HomeDisk' does NOT match server name!? 07:37:31.715 -> Jan 1 00:59:59 HomeDisk httpd[1729]: [error] mod_auth_zyxel: initialized. 07:37:32.313 -> 1442 root 1740 S < /bin/zyfw_downloader http://firmware.tdconline.dk/NSA 07:37:32.346 -> ---> still downloading, wait 2 second 07:37:32.811 -> ===> Starting schedule_controller ... 07:37:32.877 -> killall: timer_source: no process killed 07:37:32.910 -> Starting "/etc/init.d/zypkg_controller.sh". 07:37:32.943 -> Starting to set up zy-pkgs environment ... 07:37:33.043 -> cp: /etc/zyxel/zy-pkgs/*: No such file or directory 07:37:33.109 -> du: /usr/local/zy-pkgs/tmp/zypkg.log: No such file or directory 07:37:33.109 -> [: 10240: unknown operand 07:37:33.109 -> Finish "/etc/init.d/zypkg_controller.sh". 07:37:33.142 -> Starting "/etc/init.d/zypkg_controller.sh". 07:37:33.142 -> Starting all zypkgs via "/etc/init.d/zypkg_controller.sh" ... 07:37:33.275 -> - starting package "PHP-MySQL-phpMyAdmin" ... 07:37:33.275 -> ---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/PHP-MySQL-phpMyAdmin" is not existed or not excutable 07:37:33.309 -> - starting package "SqueezeCenter" ... 07:37:33.342 -> ---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/SqueezeCenter" is not existed or not excutable 07:37:33.375 -> - starting package "SMART" ... 07:37:33.408 -> ---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/SMART" is not existed or not excutable 07:37:33.441 -> /etc/init.d/zypkg_controller.sh: /etc/init.d/zypkg_controller.sh: 491: cannot open /i-data/md0/admin/zy-pkgs/USRPKG_DEPS_START: No such file 07:37:33.441 -> Finish "/etc/init.d/zypkg_controller.sh". 07:37:33.474 -> rm: cannot remove `/i-data/md0/HomeDisk/start.htm': No such file or directory 07:37:33.707 -> Starting app_wd... 07:37:33.773 -> [031m core_checksum [0m: 60e5ac84547193df98917040f063855e 07:37:33.807 -> [031m fwversion [0m: V3.34(AFN.2) 07:37:33.807 -> [031m img_checksum [0m: 7ddf39bd27e18147c31a7d325e5acc98 07:37:33.807 -> [031m modelid [0m: DA01 07:37:33.807 -> [031m revision [0m: 29152 07:37:33.807 -> [031m romfile_checksum [0m: 1A7D 07:37:33.840 -> [031m zld_checksum [0m: 72ff7c00ebca9f21c3129d854d47cdb7 07:37:33.873 -> [1976] server write-only FIFO is opened (fd=6) 07:37:33.873 -> [1976] server read-only FIFO is opened (fd=7) 07:37:33.873 -> [1976] server error read-only FIFO is opened (fd=8) 07:37:33.873 -> argc = 2, func = 641 07:37:33.873 -> argid[1]: 1346; argv[1]: enable 07:37:33.939 -> Result: Success 07:37:33.939 -> POLLHUP on 7 07:37:33.939 -> pid = 1976 07:37:33.939 -> [1976] is disconnected 07:37:33.939 -> led_state_map_addr = 46 07:37:33.939 -> Jan 1 00:59:59 HomeDisk linuxrc: Starting pid 1 07:37:34.935 -> HomeDisk login: Jan 1 00:59:59 HomeDisk ntpdate[1241]: no servers can be used, exiting
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 02, 2020 01:09AM |
Admin Registered: 14 years ago Posts: 19,425 |
Quote
/mnt/testmount/tools # ./nanddump --noecc --omitoob -l 0x80000 -f mtd0 /dev/mtd0Segmentation fault
Quote
https://forum.doozan.com/read.php?3,12381
A. Flashing Instruction:
Installation is the same for each u-Boot image, the instruction below is written to include all boxes. So choose the platform name that you are installing for, and copy/paste the appropriate commands.
If you are running kernel that do not provide mtd-utils and uboot-tools (fw_setenv, fw_printenv, flash_erase, nandwrite), you can download the NAND and U-Boot tools binaries here in this thread.
cat /proc/mtd
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 02, 2020 02:26AM |
Registered: 5 years ago Posts: 29 |
cat /proc/mtd
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 02, 2020 01:11PM |
Registered: 5 years ago Posts: 29 |
20:08:59.444 -> /mnt/sdb1 $ cat /proc/mtd 20:10:16.720 -> dev: size erasesize name 20:10:16.720 -> mtd0: 00100000 00020000 "uboot" 20:10:16.720 -> mtd1: 00080000 00020000 "uboot_env" 20:10:16.720 -> mtd2: 00080000 00020000 "key_store" 20:10:16.720 -> mtd3: 00080000 00020000 "info" 20:10:16.720 -> mtd4: 00a00000 00020000 "etc" 20:10:16.720 -> mtd5: 00a00000 00020000 "kernel_1" 20:10:16.720 -> mtd6: 02fc0000 00020000 "rootfs1" 20:10:16.720 -> mtd7: 00a00000 00020000 "kernel_2" 20:10:16.720 -> mtd8: 02fc0000 00020000 "rootfs2" 20:10:16.720 -> /mnt/sdb1 $
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 02, 2020 03:29PM |
Registered: 5 years ago Posts: 29 |
./nanddump --noecc --omitoo b -l 0x80000 -f mtd0 /dev/mtd0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00080000...
/e-data/fdea004f-2f09-4f53-87a4-c2bac9d87cbf/tools # cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "uboot" mtd1: 00080000 00020000 "uboot_env" mtd2: 00080000 00020000 "key_store" mtd3: 00080000 00020000 "info" mtd4: 00a00000 00020000 "etc" mtd5: 00a00000 00020000 "kernel_1" mtd6: 02fc0000 00020000 "rootfs1" mtd7: 00a00000 00020000 "kernel_2" mtd8: 02fc0000 00020000 "rootfs2" /e-data/fdea004f-2f09-4f53-87a4-c2bac9d87cbf/tools # cat /etc/fw_env.config # Configuration file for fw_(printenv/saveenv) utility. # Up to two entries are valid, in this case the redundand # environment sector is assumed present. # Notice, that the "Number of sectors" is ignored on NOR. # MTD device name Device offset Env. size Flash sector size Number of sectors # NAND example /dev/mtd1 0x0000 0x20000 0x20000 4 /e-data/fdea004f-2f09-4f53-87a4-c2bac9d87cbf/tools #
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 02, 2020 05:23PM |
Admin Registered: 14 years ago Posts: 19,425 |
> ./nanddump --noecc --omitoo > b -l 0x80000 -f mtd0 /dev/mtd0 > Block size 131072, page size 2048, OOB size 64 > Dumping data starting at 0x00000000 and ending at > 0x00080000... >
07:36:54.315 -> NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit) 07:36:54.315 -> Scanning device for bad blocks 07:36:54.315 -> Bad eraseblock 76 at 0x00980000 07:36:54.315 -> Bad eraseblock 281 at 0x02320000 07:36:54.315 -> Bad eraseblock 494 at 0x03dc0000 07:36:54.348 -> Bad eraseblock 703 at 0x057e0000 07:36:54.415 -> 9 cmdlinepart partitions found on MTD device nand_mtd
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 03, 2020 01:23AM |
Registered: 5 years ago Posts: 29 |
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 03, 2020 02:08AM |
Admin Registered: 14 years ago Posts: 19,425 |
Quote
UART Booting: If possible, try to test this boot image with UART booting before flashing to NAND. See davygravy's UART booting using kwboot instruction here in this thread. The latest u-boot image released here should be used for UART booting, if your box is the type that supports it (these do not: Dockstar, Pogo E02, iConnect).
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 03, 2020 01:13PM |
Registered: 5 years ago Posts: 29 |
device ide 0:1 ** File not found /boot/uImage ** device ide 1:1 ** Bad device ide 1 ** device ide 2:1 ** Bad device ide 2 ** device ide 3:1 ** Bad device ide 3 ** Scan device mmc Unknown command 'mmc' - try 'help' device mmc 0:1 ** Bad device mmc 0 ** device mmc 1:1 ** Bad device mmc 1 ** device mmc 2:1 ** Bad device mmc 2 ** device mmc 3:1 ** Bad device mmc 3 ** loading uImage ... ** Bad device usb 0 ** loading uInitrd ... ** Bad device usb 0 ** loading DTB ... ** Bad device usb 0 ** Wrong Image Format for bootm command Error occured, error code = 112 ERROR: can't get kernel image! NSA310>
U-Boot 2017.07-tld-1 (….) <your box name>
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 03, 2020 05:30PM |
Admin Registered: 14 years ago Posts: 19,425 |
Quote
Updated 25 Aug 2019:
Basic Debian buster Kirkwood rootfs for most Kirwood plugs:
- tarball size: 209M
- install size: 536M
- The init system used in this rootfs is sysvinit . To boot with systemd, see note 2 below.
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, isc-dhcp-client, dialog, bzip2, nfs server/client, iperf, ethtool, sysvinit-core, sysvinit, sysvinit-utils, u-boot-tools, and mtd-utils.
- see LED controls in /etc/rc.local, and /etc/init.d/halt
- see some useful aliases in /root/.profile
- root password: root
Download at Dropbox:
Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2
md5:
cd8ad170aa1a9fdc2a0a1c43ab1c0721
sha256:
8ccbbced367b4c2bf3728262e882f8232aff0fecd1c0c767219a0cab49a0b9bf
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 04, 2020 01:21PM |
Registered: 5 years ago Posts: 29 |
SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 Initializing devices... starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: WDC WD5000AAKX-001CA0 Firm: 15.01H15 Ser#: WD-WCAYUL098558 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Unknown command 'mmc' - try 'help' Loading envs from usb 0... ** File not found /boot/uEnv.txt ** Loading envs from usb 1... ** Bad device usb 1 ** Loading envs from usb 2... ** Bad device usb 2 ** Loading envs from usb 3... ** Bad device usb 3 ** Loading envs from ide 0... ** File not found /boot/uEnv.txt ** Loading envs from ide 1... ** Bad device ide 1 ** Loading envs from ide 2... ** Bad device ide 2 ** Loading envs from ide 3... ** Bad device ide 3 ** Loading envs from mmc 0... ** Bad device mmc 0 ** Loading envs from mmc 1... ** Bad device mmc 1 ** Loading envs from mmc 2... ** Bad device mmc 2 ** Loading envs from mmc 3... ** Bad device mmc 3 ** running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 723 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 4963680 bytes read in 911 ms (5.2 MiB/s) loading uInitrd ... 9713936 bytes read in 846 ms (11 MiB/s) loading DTB ... ** No boot file defined ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-1 Created: 2019-08-25 2:22:31 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4963616 Bytes = 4.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.2.9-kirkwood-tld-1 Created: 2019-08-25 2:22:50 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9713872 Bytes = 9.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Loading Ramdisk to 0f1ca000, end 0fb0d8d0 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: invalid dtb and unrecognized/unsupported machine ID r1=0x00000fb6, r2=0x00000100 r2[]=05 00 00 00 01 00 41 54 00 00 00 00 00 00 00 00 Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Kirkwood (Flattened Device Tree) Please check your kernel config and/or bootloader.
Begin: Running /scripts/local-block ... done. done. Gave up waiting for root file system device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Missing modules (cat /proc/modules; ls /dev) ALERT! LABEL=rootfs does not exist. Dropping to a shell! BusyBox v1.30.1 (Debian 1:1.30.1-4) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs) ls bin dev init proc run scripts tmp var conf etc lib root sbin sys usr (initramfs) mount rootfs on / type rootfs (rw) sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,nosuid,relatime,size=117388k,nr_inodes=29347,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=24532k,mode=755) (initramfs) ls /etc/ fstab ld.so.conf modprobe.d/ udev/ ld.so.cache ld.so.conf.d/ mtab
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 04, 2020 05:51PM |
Admin Registered: 14 years ago Posts: 19,425 |
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 06, 2020 01:31AM |
Registered: 5 years ago Posts: 29 |
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 06, 2020 02:15AM |
Admin Registered: 14 years ago Posts: 19,425 |
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 07, 2020 03:10PM |
Registered: 5 years ago Posts: 29 |
root@debian:/boot# parted -l Model: ATA WDC WD5000AAKX-0 (scsi) Disk /dev/sda: 500GB Sector size (logical/physical): 512B/512B Partition Table: msdos Disk Flags: Number Start End Size Type File system Flags 1 1049kB 16.9GB 16.9GB primary ext4 2 16.9GB 21.2GB 4295MB primary linux-swap(v1) 3 21.2GB 500GB 479GB primary ext4 Model: (scsi) Disk /dev/sdb: 8167MB Sector size (logical/physical): 512B/512B Partition Table: msdos Disk Flags: Number Start End Size Type File system Flags 1 1049kB 8166MB 8165MB primary ext4 Error: /dev/mtdblock2: unrecognised disk label Model: Unknown (unknown) Disk /dev/mtdblock2: 33.6MB Sector size (logical/physical): 512B/512B Partition Table: unknown Disk Flags: Error: /dev/mtdblock0: unrecognised disk label Model: Unknown (unknown) Disk /dev/mtdblock0: 1049kB Sector size (logical/physical): 512B/512B Partition Table: unknown Disk Flags: Error: /dev/mtdblock3: unrecognised disk label Model: Unknown (unknown) Disk /dev/mtdblock3: 95.4MB Sector size (logical/physical): 512B/512B Partition Table: unknown Disk Flags: Error: /dev/mtdblock1: unrecognised disk label Model: Unknown (unknown) Disk /dev/mtdblock1: 4194kB Sector size (logical/physical): 512B/512B Partition Table: unknown Disk Flags: root@debian:/boot#
root@debian:/boot# mount|grep sdb root@debian:/boot#
root@debian:/boot# ls -l /dev/disk/by-label total 0 drwxr-xr-x 2 root root 80 Mar 7 13:04 . drwxr-xr-x 7 root root 140 Mar 7 13:04 .. lrwxrwxrwx 1 root root 10 Mar 7 13:08 rootfs -> ../../sda1 lrwxrwxrwx 1 root root 10 Mar 7 13:08 rootfs_bu -> ../../sdb1 root@debian:/boot#
root@debian:/boot# cat /etc/fstab # /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> LABEL=rootfs / ext4 noatime,errors=remount-ro 0 1 /dev/sda3 /media/daten ext4 defaults 0 1 UUID=9e41369a-fb52-4f05-b1d1-0e3f2cabb176 none swap sw 0 0 tmpfs /tmp tmpfs defaults 0 0 root@debian:/boot#
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 07, 2020 04:45PM |
Admin Registered: 14 years ago Posts: 19,425 |
printenv boot
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 08, 2020 02:00PM |
Registered: 5 years ago Posts: 29 |
NSA310> printenv arcNumber=4022 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-nsa310.dtb load_dtb_addr=0x1c00000 load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=ext2load usb 0:1 0x800000 /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts init=/bin/systemd start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=echo Initializing devices...; setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in $disks; do if test $uenv_loaded -eq 0; then setenv device_type $devtype; setenv disk_number $disknum; run uenv_read; fi; done; done; uenv_read=echo Loading envs from $device_type $disk_number...; if load $device_type $disk_number:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; echo ... envs loaded; fi usb_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi usb_ready_retry=15 Environment size: 2854/131068 bytes NSA310>
NSA310> boot Initializing devices... starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: WDC WD5000AAKX-001CA0 Firm: 15.01H15 Ser#: WD-WCAYUL098558 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Unknown command 'mmc' - try 'help' Loading envs from usb 0... ** Bad device usb 0 ** Loading envs from usb 1... ** Bad device usb 1 ** Loading envs from usb 2... ** Bad device usb 2 ** Loading envs from usb 3... ** Bad device usb 3 ** Loading envs from ide 0... ** File not found /boot/uEnv.txt ** Loading envs from ide 1... ** Bad device ide 1 ** Loading envs from ide 2... ** Bad device ide 2 ** Loading envs from ide 3... ** Bad device ide 3 ** Loading envs from mmc 0... ** Bad device mmc 0 ** Loading envs from mmc 1... ** Bad device mmc 1 ** Loading envs from mmc 2... ** Bad device mmc 2 ** Loading envs from mmc 3... ** Bad device mmc 3 ** running scan_disk ... Scan device usb device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: WDC WD5000AAKX-001CA0 Firm: 15.01H15 Ser#: WD-WCAYUL098558 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) device ide 0:1 1 bytes read in 47 ms (0 Bytes/s) Found bootable drive on ide 0 ** Bad device usb 0 ** ** Bad device usb 0 ** ** Bad device usb 0 ** Wrong Image Format for bootm command Error occured, error code = 112 ERROR: can't get kernel image! NSA310>
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 08, 2020 06:01PM |
Admin Registered: 14 years ago Posts: 19,425 |
ver setenv load_dtb 'echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file' setenv load_initrd 'echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv load_uimage 'echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage' printenv boot
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 09, 2020 02:09PM |
Registered: 5 years ago Posts: 29 |
� U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:54:15 -0700) ZyXEL NSA310 1-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA310> ver U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:54:15 -0700) ZyXEL NSA310 1-Bay Power Media Server gcc (Debian 6.3.0-18) 6.3.0 20170516 GNU ld (GNU Binutils for Debian) 2.28 NSA310> setenv load_dtb 'echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file' NSA310> setenv load_initrd 'echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd' NSA310> setenv load_uimage 'echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage' NSA310> printenv arcNumber=4022 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts init=/bin/systemd start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=echo Initializing devices...; setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in $disks; do if test $uenv_loaded -eq 0; then setenv device_type $devtype; setenv disk_number $disknum; run uenv_read; fi; done; done; uenv_read=echo Loading envs from $device_type $disk_number...; if load $device_type $disk_number:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; echo ... envs loaded; fi usb_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi usb_ready_retry=15 Environment size: 2954/131068 bytes NSA310> boot Initializing devices... starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: WDC WD5000AAKX-001CA0 Firm: 15.01H15 Ser#: WD-WCAYUL098558 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Unknown command 'mmc' - try 'help' Loading envs from usb 0... ** Bad device usb 0 ** Loading envs from usb 1... ** Bad device usb 1 ** Loading envs from usb 2... ** Bad device usb 2 ** Loading envs from usb 3... ** Bad device usb 3 ** Loading envs from ide 0... ** File not found /boot/uEnv.txt ** Loading envs from ide 1... ** Bad device ide 1 ** Loading envs from ide 2... ** Bad device ide 2 ** Loading envs from ide 3... ** Bad device ide 3 ** Loading envs from mmc 0... ** Bad device mmc 0 ** Loading envs from mmc 1... ** Bad device mmc 1 ** Loading envs from mmc 2... ** Bad device mmc 2 ** Loading envs from mmc 3... ** Bad device mmc 3 ** running scan_disk ... Scan device usb device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: WDC WD5000AAKX-001CA0 Firm: 15.01H15 Ser#: WD-WCAYUL098558 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) device ide 0:1 1 bytes read in 47 ms (0 Bytes/s) Found bootable drive on ide 0 loading uImage ... 5202928 bytes read in 1097 ms (4.5 MiB/s) loading uInitrd ... 9743560 bytes read in 2096 ms (4.4 MiB/s) loading DTB ... ** No boot file defined ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.5.1-kirkwood-tld-1 Created: 2020-03-04 20:55:12 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5202864 Bytes = 5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.5.1-kirkwood-tld-1 Created: 2020-03-04 20:55:42 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9743496 Bytes = 9.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Loading Ramdisk to 0f1c2000, end 0fb0cc88 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: invalid dtb and unrecognized/unsupported machine ID r1=0x00000fb6, r2=0x00000100 r2[]=05 00 00 00 01 00 41 54 00 00 00 00 00 00 00 00 Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Kirkwood (Flattened Device Tree) Please check your kernel config and/or bootloader.
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 09, 2020 05:36PM |
Admin Registered: 14 years ago Posts: 19,425 |
setenv devices 'usb ide' setenv bootdev usb setenv load_dtb 'echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file' setenv load_initrd 'echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv load_uimage 'echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage' boot
mkdir -p /media/sda1 mount -o noatime /dev/sda1 /media/sda1
cd /media/sda1/boot cp -a uImage uImage.nsa310_with_dtb cp -a uImage.orig uImage sync ls -lart /media/sda1/boot
shutdown -h now
setenv devices 'ide usb' setenv bootdev ide setenv load_dtb 'echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file' setenv load_initrd 'echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv load_uimage 'echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage' boot
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 10, 2020 02:01PM |
Registered: 5 years ago Posts: 29 |
NSA310> setenv devices 'usb ide' NSA310> setenv bootdev usb NSA310> setenv load_dtb 'echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file' NSA310> setenv load_initrd 'echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd' NSA310> setenv load_uimage 'echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage' NSA310> boot Initializing devices... starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: WDC WD5000AAKX-001CA0 Firm: 15.01H15 Ser#: WD-WCAYUL098558 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Loading envs from usb 0... ** File not found /boot/uEnv.txt ** Loading envs from usb 1... ** Bad device usb 1 ** Loading envs from usb 2... ** Bad device usb 2 ** Loading envs from usb 3... ** Bad device usb 3 ** Loading envs from ide 0... ** File not found /boot/uEnv.txt ** Loading envs from ide 1... ** Bad device ide 1 ** Loading envs from ide 2... ** Bad device ide 2 ** Loading envs from ide 3... ** Bad device ide 3 ** running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 723 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 5202928 bytes read in 919 ms (5.4 MiB/s) loading uInitrd ... 9743560 bytes read in 849 ms (10.9 MiB/s) loading DTB ... ** No boot file defined ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.5.1-kirkwood-tld-1 Created: 2020-03-04 20:55:12 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5202864 Bytes = 5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.5.1-kirkwood-tld-1 Created: 2020-03-04 20:55:42 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9743496 Bytes = 9.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Loading Ramdisk to 0f1c2000, end 0fb0cc88 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: invalid dtb and unrecognized/unsupported machine ID r1=0x00000fb6, r2=0x00000100 r2[]=05 00 00 00 01 00 41 54 00 00 00 00 00 00 00 00 Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Kirkwood (Flattened Device Tree) Please check your kernel config and/or bootloader.I can start without any intervention from USB though, was that the goal?
NSA310> printenv arcNumber=4022 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-nsa310.dtb load_dtb_addr=0x1c00000 load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=ext2load usb 0:1 0x800000 /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts init=/bin/systemd start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=echo Initializing devices...; setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in $disks; do if test $uenv_loaded -eq 0; then setenv device_type $devtype; setenv disk_number $disknum; run uenv_read; fi; done; done; uenv_read=echo Loading envs from $device_type $disk_number...; if load $device_type $disk_number:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; echo ... envs loaded; fi usb_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi usb_ready_retry=15 Environment size: 2854/131068 bytes NSA310>
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 10, 2020 05:30PM |
Admin Registered: 14 years ago Posts: 19,425 |
setenv devices 'ide usb' setenv bootdev ide setenv dtb_file '/boot/dts/kirkwood-nsa310.dtb' setenv load_dtb 'echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file' setenv load_initrd 'echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv load_uimage 'echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage' boot
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 11, 2020 02:21PM |
Registered: 5 years ago Posts: 29 |
setenv dtb_file /boot/dts/kirkwood-nsa310.dtb
root@debian:~# uname -a Linux debian 5.2.9-kirkwood-tld-1 #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 armv5tel GNU/Linux
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 11, 2020 06:20PM |
Admin Registered: 14 years ago Posts: 19,425 |
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 12, 2020 03:32AM |
Registered: 5 years ago Posts: 29 |
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 12, 2020 04:00AM |
Admin Registered: 14 years ago Posts: 19,425 |
Quote
4b. Boot with DTB file embedded in the kernel image (no U-Boot envs changes are needed if your system already booting on USB or HDD). Again, this step 4b is for stock U-Boot only.
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 12, 2020 03:44PM |
Registered: 5 years ago Posts: 29 |
NSA310> boot Initializing devices... Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: WDC WD5000AAKX-001CA0 Firm: 15.01H15 Ser#: WD-WCAYUL098558 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Loading envs from ide 0... ** File not found /boot/uEnv.txt ** Loading envs from ide 1... ** Bad device ide 1 ** Loading envs from ide 2... ** Bad device ide 2 ** Loading envs from ide 3... ** Bad device ide 3 ** Loading envs from usb 0... ** File not found /boot/uEnv.txt ** Loading envs from usb 1... ** Bad device usb 1 ** Loading envs from usb 2... ** Bad device usb 2 ** Loading envs from usb 3... ** Bad device usb 3 ** running scan_disk ... Scan device ide Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: WDC WD5000AAKX-001CA0 Firm: 15.01H15 Ser#: WD-WCAYUL098558 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) device ide 0:1 1 bytes read in 53 ms (0 Bytes/s) Found bootable drive on ide 0 loading uImage ... 5202928 bytes read in 1096 ms (4.5 MiB/s) loading uInitrd ... 9138783 bytes read in 1885 ms (4.6 MiB/s) loading DTB /boot/dts/kirkwood-nsa310.dtb ... 12568 bytes read in 27 ms (454.1 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.5.1-kirkwood-tld-1 Created: 2020-02-07 16:13:19 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5202864 Bytes = 5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.5.1-kirkwood-tld-1 Created: 2020-02-07 16:13:27 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9138719 Bytes = 8.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f256000, end 0fb0d21f ... OK Loading Device Tree to 0f24f000, end 0f255117 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.5.1-kirkwood-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1.0 PREEMPT Sat Feb 1 22:28:36 PST 2020 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: ZyXEL NSA310 [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) init=/bin/systemd [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 234256K/262144K available (9216K kernel code, 926K rwdata, 3860K rodata, 1024K init, 296K bss, 27888K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x470/0x80c with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000052][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.000837][ T0] Console: colour dummy device 80x30 [ 0.000890][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000916][ T0] pid_max: default: 32768 minimum: 301 [ 0.001293][ T0] LSM: Security Framework initializing [ 0.001465][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001492][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001646][ T0] *** VALIDATE tmpfs *** [ 0.002523][ T0] *** VALIDATE proc *** [ 0.002784][ T0] *** VALIDATE cgroup1 *** [ 0.002810][ T0] *** VALIDATE cgroup2 *** [ 0.002920][ T0] CPU: Testing write buffer coherency: ok [ 0.004892][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.005205][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.005526][ T1] rcu: Hierarchical SRCU implementation. [ 0.008235][ T1] devtmpfs: initialized [ 0.015506][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.015545][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.015831][ T1] xor: measuring software checksum speed [ 0.110127][ T1] arm4regs : 1088.400 MB/sec [ 0.210083][ T1] 8regs : 653.600 MB/sec [ 0.310081][ T1] 32regs : 950.000 MB/sec [ 0.310100][ T1] xor: using function: arm4regs (1088.400 MB/sec) [ 0.310121][ T1] prandom: seed boundary self test passed [ 0.314299][ T1] prandom: 100 self tests passed [ 0.314310][ T1] pinctrl core: initialized pinctrl subsystem [ 0.315285][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.315981][ T1] NET: Registered protocol family 16 [ 0.316744][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.317742][ T1] audit: initializing netlink subsys (disabled) [ 0.319179][ T14] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 [ 0.319313][ T1] cpuidle: using governor ladder [ 0.319400][ T1] cpuidle: using governor menu [ 0.319955][ T1] Feroceon L2: Enabling L2 [ 0.320007][ T1] Feroceon L2: Cache support initialised. [ 0.326213][ T1] No ATAGs? [ 2.560060][ C0] random: fast init done [ 5.400337][ T1] raid6: int32x8 gen() 105 MB/s [ 5.570404][ T1] raid6: int32x8 xor() 65 MB/s [ 5.740276][ T1] raid6: int32x4 gen() 106 MB/s [ 5.910400][ T1] raid6: int32x4 xor() 69 MB/s [ 6.080318][ T1] raid6: int32x2 gen() 132 MB/s [ 6.250293][ T1] raid6: int32x2 xor() 94 MB/s [ 6.420421][ T1] raid6: int32x1 gen() 100 MB/s [ 6.590440][ T1] raid6: int32x1 xor() 69 MB/s [ 6.590451][ T1] raid6: using algorithm int32x2 gen() 132 MB/s [ 6.590460][ T1] raid6: .... xor() 94 MB/s, rmw enabled [ 6.590468][ T1] raid6: using intx1 recovery algorithm [ 6.590759][ T1] vgaarb: loaded [ 6.591366][ T1] SCSI subsystem initialized [ 6.591904][ T1] usbcore: registered new interface driver usbfs [ 6.591973][ T1] usbcore: registered new interface driver hub [ 6.592063][ T1] usbcore: registered new device driver usb [ 6.592273][ T1] pps_core: LinuxPPS API ver. 1 registered [ 6.592285][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.592314][ T1] PTP clock support registered [ 6.593837][ T1] clocksource: Switched to clocksource orion_clocksource [ 7.933973][ T1] *** VALIDATE bpf *** [ 7.934441][ T1] VFS: Disk quotas dquot_6.6.0 [ 7.934534][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 7.934641][ T1] *** VALIDATE ramfs *** [ 7.945364][ T1] NET: Registered protocol family 2 [ 7.946260][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 7.946302][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 7.946344][ T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 7.946376][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 7.946520][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 7.946552][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 7.946786][ T1] NET: Registered protocol family 1 [ 7.947549][ T1] RPC: Registered named UNIX socket transport module. [ 7.947563][ T1] RPC: Registered udp transport module. [ 7.947572][ T1] RPC: Registered tcp transport module. [ 7.947580][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 7.947595][ T1] PCI: CLS 0 bytes, default 32 [ 7.947931][ T1] Trying to unpack rootfs image as initramfs... [ 7.950306][ T1] Initramfs unpacking failed: broken padding [ 7.975897][ T1] Freeing initrd memory: 8928K [ 7.976089][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 7.977434][ T1] Initialise system trusted keyrings [ 7.977493][ T1] Key type blacklist registered [ 7.977728][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 7.977836][ T1] zbud: loaded [ 7.979094][ T1] NFS: Registering the id_resolver key type [ 7.979128][ T1] Key type id_resolver registered [ 7.979138][ T1] Key type id_legacy registered [ 7.979162][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 7.979180][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 7.979612][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 7.980087][ T1] *** VALIDATE jffs2 *** [ 7.980105][ T1] fuse: init (API version 7.31) [ 7.980126][ T1] *** VALIDATE fuse *** [ 7.980140][ T1] *** VALIDATE fuse *** [ 7.980529][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 7.980748][ T1] orangefs_init: module version upstream loaded [ 7.980762][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 7.981515][ T1] *** VALIDATE xfs *** [ 8.019067][ T1] async_tx: api initialized (async) [ 8.019092][ T1] Key type asymmetric registered [ 8.019102][ T1] Asymmetric key parser 'x509' registered [ 8.019161][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 8.020743][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 8.022227][ T1] mvebu-gpio f1010140.gpio: IRQ index 3 not found [ 8.022846][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 8.022869][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 8.022885][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 8.022900][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 8.023023][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 8.023065][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 8.024608][ T1] PCI: bus0: Fast back to back transfers disabled [ 8.024638][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 8.024871][ T1] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 [ 8.024915][ T1] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff] [ 8.024946][ T1] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit pref] [ 8.024971][ T1] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 8.024992][ T1] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 8.025099][ T1] pci 0000:01:00.0: supports D1 D2 [ 8.025114][ T1] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 8.055081][ T1] PCI: bus1: Fast back to back transfers disabled [ 8.055111][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 8.055322][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 8.055340][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 8.055357][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref] [ 8.055380][ T1] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref] [ 8.055397][ T1] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0010000-0xe0013fff 64bit pref] [ 8.055423][ T1] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0014000-0xe0014fff 64bit pref] [ 8.055447][ T1] pci 0000:01:00.0: BAR 0: assigned [io 0x10000-0x100ff] [ 8.055464][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 8.055479][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 8.055497][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 8.055615][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 8.056182][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 8.114886][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 8.117463][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 8.174859][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 8.177738][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 8.179145][ T1] printk: console [ttyS0] disabled [ 8.179244][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 9.185997][ T1] printk: console [ttyS0] enabled [ 9.199438][ T1] loop: module loaded [ 9.203981][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 9.213237][ T1] scsi host0: sata_mv [ 9.217750][ T1] scsi host1: sata_mv [ 9.221880][ T1] ata1: SATA max UDMA/133 irq 32 [ 9.226762][ T1] ata2: SATA max UDMA/133 irq 32 [ 9.232601][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 9.239815][ T1] nand: Samsung NAND 128MiB 3,3V 8-bit [ 9.245186][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 9.253501][ T1] Scanning device for bad blocks [ 9.265690][ T1] Bad eraseblock 76 at 0x000000980000 [ 9.290583][ T1] Bad eraseblock 281 at 0x000002320000 [ 9.316350][ T1] Bad eraseblock 494 at 0x000003dc0000 [ 9.341727][ T1] Bad eraseblock 703 at 0x0000057e0000 [ 9.377856][ T1] 4 cmdlinepart partitions found on MTD device orion_nand [ 9.384874][ T1] Creating 4 MTD partitions on "orion_nand": [ 9.390754][ T1] 0x000000000000-0x000000100000 : "u-boot" [ 9.397942][ T1] 0x000000100000-0x000000500000 : "uImage" [ 9.405061][ T1] 0x000000500000-0x000002500000 : "rootfs" [ 9.412244][ T1] 0x000002500000-0x000008000000 : "data" [ 9.420860][ T1] libphy: Fixed MDIO Bus: probed [ 9.426504][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 9.433797][ T1] ehci-pci: EHCI PCI platform driver [ 9.439052][ T1] ehci-orion: EHCI orion driver [ 9.444012][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 9.450257][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 9.458929][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 9.493862][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 9.500913][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.05 [ 9.509968][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.517965][ T1] usb usb1: Product: EHCI Host Controller [ 9.523592][ T1] usb usb1: Manufacturer: Linux 5.5.1-kirkwood-tld-1 ehci_hcd [ 9.530981][ T1] usb usb1: SerialNumber: f1050000.ehci [ 9.537135][ T1] hub 1-0:1.0: USB hub found [ 9.541683][ T1] hub 1-0:1.0: 1 port detected [ 9.547201][ T1] usbcore: registered new interface driver usb-storage [ 9.554416][ T1] mousedev: PS/2 mouse device common for all mice [ 9.561537][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 9.567431][ T1] i2c /dev entries driver [ 9.573220][ T1] device-mapper: uevent: version 1.0.3 [ 9.578998][ T1] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 9.588678][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 9.596014][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 9.603359][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 9.610809][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 9.617662][ T1] device-mapper: raid: Loading target version 1.15.0 [ 9.626795][ T1] hid: raw HID events driver (C) Jiri Kosina [ 9.633007][ T1] exFAT: Version 1.3.0 [ 9.637088][ T1] drop_monitor: Initializing network drop monitor service [ 9.644406][ T1] NET: Registered protocol family 17 [ 9.649839][ T1] Key type dns_resolver registered [ 9.655505][ T1] registered taskstats version 1 [ 9.660325][ T1] Loading compiled-in X.509 certificates [ 9.665989][ T1] zswap: loaded using pool lzo/zbud [ 9.671275][ T1] Key type ._fscrypt registered [ 9.676036][ T1] Key type .fscrypt registered [ 9.702368][ T1] Key type big_key registered [ 9.710651][ T1] Key type encrypted registered [ 9.718528][ T1] Waiting 10 sec before mounting root device... [ 9.733929][ T118] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 9.745500][ T118] ata1.00: ATA-8: WDC WD5000AAKX-001CA0, 15.01H15, max UDMA/133 [ 9.753023][ T118] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 9.765200][ T118] ata1.00: configured for UDMA/133 [ 9.780747][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD5000AAKX-0 1H15 PQ: 0 ANSI: 5 [ 9.790908][ T122] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 9.799729][ T122] sd 0:0:0:0: [sda] Write Protect is off [ 9.805474][ T122] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 9.829226][ T122] sda: sda1 sda2 sda3 [ 9.835223][ T122] sd 0:0:0:0: [sda] Attached SCSI disk [ 9.913875][ T5] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 9.965816][ T5] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.63 [ 9.974771][ T5] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 9.982660][ T5] usb 1-1: Product: USB2.0 Hub [ 9.988114][ T5] hub 1-1:1.0: USB hub found [ 9.992939][ T5] hub 1-1:1.0: 4 ports detected [ 10.135492][ T120] ata2: SATA link down (SStatus 0 SControl F300) [ 10.313868][ T5] usb 1-1.3: new high-speed USB device number 3 using orion-ehci [ 10.366188][ T5] usb 1-1.3: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00 [ 10.375313][ T5] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 10.383379][ T5] usb 1-1.3: SerialNumber: T1205060000776 [ 10.389775][ T5] usb-storage 1-1.3:1.0: USB Mass Storage device detected [ 10.397305][ T5] scsi host2: usb-storage 1-1.3:1.0 [ 11.638681][ T22] scsi 2:0:0:0: Direct-Access 1100 PQ: 0 ANSI: 4 [ 11.649234][ T122] sd 2:0:0:0: [sdb] 15950592 512-byte logical blocks: (8.17 GB/7.61 GiB) [ 11.658220][ T122] sd 2:0:0:0: [sdb] Write Protect is off [ 11.664343][ T122] sd 2:0:0:0: [sdb] No Caching mode page found [ 11.670387][ T122] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 11.681588][ T122] sdb: sdb1 [ 11.687848][ T122] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 20.323944][ T1] md: Waiting for all devices to be available before autodetect [ 20.331485][ T1] md: If you don't use raid, use raid=noautodetect [ 20.338790][ T1] md: Autodetecting RAID arrays. [ 20.343606][ T1] md: autorun ... [ 20.347187][ T1] md: ... autorun DONE. [ 20.351442][ T1] VFS: Cannot open root device "LABEL=rootfs" or unknown-block(0,0): error -6 [ 20.360248][ T1] Please append a correct "root=" boot option; here are the available partitions: [ 20.369431][ T1] 1f00 1024 mtdblock0 [ 20.369434][ T1] (driver?) [ 20.377457][ T1] 1f01 4096 mtdblock1 [ 20.377460][ T1] (driver?) [ 20.385469][ T1] 1f02 32768 mtdblock2 [ 20.385472][ T1] (driver?) [ 20.393437][ T1] 1f03 93184 mtdblock3 [ 20.393439][ T1] (driver?) [ 20.401435][ T1] 0800 488386584 sda [ 20.401439][ T1] driver: sd [ 20.408994][ T1] 0801 16547840 sda1 00000000-01 [ 20.408997][ T1] [ 20.416816][ T1] 0802 4194304 sda2 00000000-02 [ 20.416818][ T1] [ 20.424630][ T1] 0803 467643416 sda3 00000000-03 [ 20.424633][ T1] [ 20.432425][ T1] 0810 7975296 sdb [ 20.432428][ T1] driver: sd [ 20.439985][ T1] 0811 7973888 sdb1 6633f146-01 [ 20.439988][ T1] [ 20.447798][ T1] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 20.456806][ T1] CPU: 0 PID: 1 Comm: swapper Not tainted 5.5.1-kirkwood-tld-1 #1.0 [ 20.464665][ T1] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 20.471688][ T1] [<8010f668>] (unwind_backtrace) from [<8010b9f4>] (show_stack+0x10/0x14) [ 20.480170][ T1] [<8010b9f4>] (show_stack) from [<80119e8c>] (panic+0xfc/0x328) [ 20.487789][ T1] [<80119e8c>] (panic) from [<80f0157c>] (mount_block_root+0x1c8/0x260) [ 20.496007][ T1] [<80f0157c>] (mount_block_root) from [<80f01704>] (mount_root+0xf0/0x130) [ 20.504578][ T1] [<80f01704>] (mount_root) from [<80f01888>] (prepare_namespace+0x144/0x180) [ 20.513323][ T1] [<80f01888>] (prepare_namespace) from [<80f010a4>] (kernel_init_freeable+0x144/0x1a0) [ 20.522950][ T1] [<80f010a4>] (kernel_init_freeable) from [<809d9904>] (kernel_init+0x8/0x10c) [ 20.531873][ T1] [<809d9904>] (kernel_init) from [<801010e0>] (ret_from_fork+0x14/0x34) [ 20.540173][ T1] Exception stack(0x8ec3dfb0 to 0x8ec3dff8) [ 20.545948][ T1] dfa0: 00000000 00000000 00000000 00000000 [ 20.554861][ T1] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 20.563773][ T1] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 20.571125][ T1] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---
root@debian:~# lsblk -o name,label NAME LABEL sda |-sda1 rootfs |-sda2 `-sda3 sdb `-sdb1 rootfs mtdblock0 mtdblock1 mtdblock2 mtdblock3 root@debian:~#
NSA310> printenv dtb_file=/boot/dts/kirkwood-nsa310.dtb arcNumber=4022 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=ide device=0:1 devices=ide usb disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-nsa310.dtb ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts init=/bin/systemd start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=echo Initializing devices...; setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in $disks; do if test $uenv_loaded -eq 0; then setenv device_type $devtype; setenv disk_number $disknum; run uenv_read; fi; done; done; uenv_read=echo Loading envs from $device_type $disk_number...; if load $device_type $disk_number:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; echo ... envs loaded; fi usb_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi usb_ready_retry=15 Environment size: 3033/131068 bytes
Re: U-Boot Kirkwood - NSA310 - nandump segfault March 12, 2020 06:59PM |
Admin Registered: 14 years ago Posts: 19,425 |
setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts'
boot