Restore uboot for Synology DS414
Posted by bignellrp
|
Re: Restore uboot for Synology DS414 April 12, 2020 05:05PM |
Admin Registered: 14 years ago Posts: 19,932 |
bignellrp,
> GOT IT!!! I 100% owe you a beer. I will
> certainly be donating to the charity from your
> link. (https://www.doctorswithoutborders.org/)
>
Awesome!
The reason it did not like the label was because you did not load uInitrd. The root device /dev/sda1 points the kernel to the first disk. In this case it works because it is the only disk in the system. When you load initrd, it will find the disk partition with label rootfs. And then it does not matter how many partitions/disks you have plugged in, the kernel will always able to find the rootfs.
OK so it is all set! Now before flashing u-boot inside Debian, we need to define the mtd devices (mtdparts) in bootargs. The ones we have now came from the DTS, so it is likely write-protected. And the definition is misleading, it is actually u-boot (not RedBoot).
This box predefine mtds are slightly different from the RS816. But basically the boot loader is in mtd0. So we can flash it without worrying (based on the RS816 example).
Let me write the flashing commands in the next post.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 04/12/2020 05:07PM by bodhi.
> GOT IT!!! I 100% owe you a beer. I will
> certainly be donating to the charity from your
> link. (https://www.doctorswithoutborders.org/)
>
Awesome!
The reason it did not like the label was because you did not load uInitrd. The root device /dev/sda1 points the kernel to the first disk. In this case it works because it is the only disk in the system. When you load initrd, it will find the disk partition with label rootfs. And then it does not matter how many partitions/disks you have plugged in, the kernel will always able to find the rootfs.
Quote
=> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 earlyprintk=serial'
=> ext2load usb 0:1 2000000 boot/uImage
5074848 bytes read in 227 ms (21.3 MiB/s)
=> bootm 0x2000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-5.2.9-mvebu-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5074784 Bytes = 4.8 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image
Starting kernel ...
Quote
> 192.168.0.37
> Synology DS414
> Linux version 5.2.9-mvebu-tld-1 (root@tldDebianVM)
> (gcc version 7.4.0 (Ubuntu/Linaro
> 7.4.0-1ubuntu1~18.04.1)) #1 SMP PREEMPT Mon Aug 19
> 12:47:39 PDT 2019
> Debian 10.0
> Sun Apr 12 05:48:40 PDT 2020 up 4 minutes
OK so it is all set! Now before flashing u-boot inside Debian, we need to define the mtd devices (mtdparts) in bootargs. The ones we have now came from the DTS, so it is likely write-protected. And the definition is misleading, it is actually u-boot (not RedBoot).
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 000d0000 00001000 "RedBoot" mtd1: 002d0000 00001000 "zImage" mtd2: 00430000 00001000 "rd.gz" mtd3: 00010000 00001000 "vendor" mtd4: 00010000 00001000 "RedBoot config" mtd5: 00010000 00001000 "FIS directory"
This box predefine mtds are slightly different from the RS816. But basically the boot loader is in mtd0. So we can flash it without worrying (based on the RS816 example).
Let me write the flashing commands in the next post.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 04/12/2020 05:07PM by bodhi.
|
Re: Restore uboot for Synology DS414 April 12, 2020 05:12PM |
Admin Registered: 14 years ago Posts: 19,932 |
bignellrp ,
What is the size of uboot_DS414r1.bin in bytes?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
What is the size of uboot_DS414r1.bin in bytes?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Restore uboot for Synology DS414 April 12, 2020 05:47PM |
Admin Registered: 14 years ago Posts: 19,932 |
Restore stock u-boot.
Prerequisite:
Make sure the uboot_DS414r1.bin size is less than or equal to 832K. If it is larger, then it will not work.
Flashing Steps:
Repeat the kwboot booting. Interrupt serial console and
And then load and boot
Let it boot all the way into Debian. Login, and verify the mtds. We want to see 2 partition. And the 1st looks like:
cat /proc/mtd
If the mtd0 looks like above, go ahead and flash
Note that if flash_unlock give you error, you can ignore it. If there is error after flashcp here then stop and post the entire serial console log until this point.
Now if kwboot is still running, it is OK. It runs as a normal serial comm terminal too. Or you can start picocom/minicom to run a regular serial console.
Reboot and let it boot automatically, watch the serial console to observe progress. See if stock u-boot can run. Interrupt serial console. And see if the envs are normal.
Done.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 04/13/2020 05:44PM by bodhi.
Prerequisite:
Make sure the uboot_DS414r1.bin size is less than or equal to 832K. If it is larger, then it will not work.
Flashing Steps:
Repeat the kwboot booting. Interrupt serial console and
setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 mtdparts=spi0.0:832K(u-boot),-(data) earlyprintk=serial'
And then load and boot
ext2load usb 0:1 2000000 boot/uImage
Let it boot all the way into Debian. Login, and verify the mtds. We want to see 2 partition. And the 1st looks like:
cat /proc/mtd
dev: size erasesize name mtd0: 000d0000 00001000 "u-boot"
If the mtd0 looks like above, go ahead and flash
flash_unlock /dev/mtd0 flashcp -v uboot_DS414r1.bin /dev/mtd0
Note that if flash_unlock give you error, you can ignore it. If there is error after flashcp here then stop and post the entire serial console log until this point.
Now if kwboot is still running, it is OK. It runs as a normal serial comm terminal too. Or you can start picocom/minicom to run a regular serial console.
Reboot and let it boot automatically, watch the serial console to observe progress. See if stock u-boot can run. Interrupt serial console. And see if the envs are normal.
Done.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 04/13/2020 05:44PM by bodhi.
|
Re: Restore uboot for Synology DS414 April 13, 2020 01:52AM |
Registered: 5 years ago Posts: 48 |
First attempt to boot back into debian with the new bootargs failed. Something about the label again:
I'll try again
I'll try again
92 % [......................................................................]
93 % [......................................................................]
95 % [......................................................................]
96 % [......................................................................]
97 % [......................................................................]
99 % [.....................................................]
[Type Ctrl-\ + c to quit]
U-Boot 2019.10-tld-1 (Apr 09 2020 - 16:26:57 -0700)
SoC: MV78230-B0 at 1333 MHz
I2C: ready
DRAM: 1 GiB (667 MHz, 32-bit, ECC not enabled)
Loading Environment from SPI Flash... SF: Detected n25q064 with page size 256 Bytes, erase size 4 KiB, total 8 MiB
*** Warning - bad CRC, using default environment
In: serial@12000
Out: serial@12000
Err: serial@12000
Model: Synology DS414
Board: DS414
Net:
Warning: ethernet@70000 (eth0) using random MAC address - 6a:8f:6a:eb:21:ea
eth0: ethernet@70000
Warning: ethernet@74000 (eth1) using random MAC address - b2:69:e6:99:9b:b6
, eth1: ethernet@74000
starting USB...
Bus usb@50000: USB EHCI 1.00
scanning bus usb@50000 for devices...
USB retry period from the environment: 0 second(s)
2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
SF: Detected n25q064 with page size 256 Bytes, erase size 4 KiB, total 8 MiB
Hit any key to stop autoboot: 0
device 0 offset 0xd0000, size 0x700000
SF: 7340032 bytes @ 0xd0000 Read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
=> setenv mtdparts 'mtdparts=spi0.0:832K(u-boot),-(data)'
=> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial'
=> ext2load usb 0:1 2000000 boot/uImage
5074848 bytes read in 226 ms (21.4 MiB/s)
=> bootm 0x2000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-5.2.9-mvebu-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5074784 Bytes = 4.8 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.2.9-mvebu-tld-1 (root@tldDebianVM) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1)) #1 SMP PREEMPT Mon Aug 19 12:47:39 PDT 2019
[ 0.000000][ T0] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d
[ 0.000000][ T0] CPU: div instructions available: patching division code
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Synology DS414
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writealloc
[ 0.000000][ T0] percpu: Embedded 21 pages/cpu s55244 r8192 d22580 u86016
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000][ T0] Memory: 1023808K/1048576K available (10240K kernel code, 833K rwdata, 2724K rodata, 1024K init, 343K bss, 24768K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x30c/0x830 with crng_init=0
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000][ T0] Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x1a096b00 -> 0x1a096b02
[ 0.000000][ T0] Aurora cache controller enabled, 16 ways, 1024 kB
[ 0.000000][ T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a096b02
[ 0.000000][ T0] Switching to timer-based delay loop, resolution 40ns
[ 0.000005][ T0] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.008557][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.020795][ T0] Console: colour dummy device 80x30
[ 0.025969][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.037074][ T0] pid_max: default: 32768 minimum: 301
[ 0.042535][ T0] LSM: Security Framework initializing
[ 0.047922][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.055268][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.063487][ T0] *** VALIDATE proc ***
[ 0.067653][ T0] *** VALIDATE cgroup1 ***
[ 0.071951][ T0] *** VALIDATE cgroup2 ***
[ 0.076277][ T0] CPU: Testing write buffer coherency: ok
[ 0.082079][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.140234][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.147383][ T1] mvebu-soc-id: MVEBU SoC ID=0x7823, Rev=0x2
[ 0.153366][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.180197][ T1] rcu: Hierarchical SRCU implementation.
[ 0.220196][ T1] smp: Bringing up secondary CPUs ...
[ 0.280299][ T1] Booting CPU 1
[ 0.284042][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.294137][ T1] smp: Brought up 1 node, 2 CPUs
[ 0.305348][ T1] SMP: Total of 2 processors activated (100.00 BogoMIPS).
[ 0.312342][ T1] CPU: All CPU(s) started in SVC mode.
[ 0.318363][ T1] devtmpfs: initialized
[ 0.325715][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[ 0.334571][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.345150][ T1] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.352121][ T1] xor: measuring software checksum speed
[ 0.450185][ T1] arm4regs : 1290.800 MB/sec
[ 0.550185][ T1] 8regs : 810.000 MB/sec
[ 0.650184][ T1] 32regs : 1146.400 MB/sec
[ 0.655076][ T1] xor: using function: arm4regs (1290.800 MB/sec)
[ 0.661372][ T1] prandom: seed boundary self test passed
[ 0.669267][ T1] prandom: 100 self tests passed
[ 0.674082][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.681358][ T1] NET: Registered protocol family 16
[ 0.686859][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.695016][ T1] audit: initializing netlink subsys (disabled)
[ 0.701307][ T33] audit: type=2000 audit(0.680:1): state=initialized audit_enabled=0 res=1
[ 0.710234][ T1] cpuidle: using governor ladder
[ 0.715066][ T1] cpuidle: using governor menu
[ 0.719898][ T12] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0
[ 0.729665][ T12] hw-breakpoint: CPU 0 failed to disable vector catch
[ 0.736357][ T13] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1
[ 0.960393][ T1] raid6: int32x8 gen() 227 MB/s
[ 1.130327][ T1] raid6: int32x8 xor() 134 MB/s
[ 1.300426][ T1] raid6: int32x4 gen() 206 MB/s
[ 1.470241][ T1] raid6: int32x4 xor() 163 MB/s
[ 1.640402][ T1] raid6: int32x2 gen() 197 MB/s
[ 1.810207][ T1] raid6: int32x2 xor() 210 MB/s
[ 1.980255][ T1] raid6: int32x1 gen() 135 MB/s
[ 2.150302][ T1] raid6: int32x1 xor() 182 MB/s
[ 2.155296][ T1] raid6: using algorithm int32x8 gen() 227 MB/s
[ 2.161404][ T1] raid6: .... xor() 134 MB/s, rmw enabled
[ 2.166999][ T1] raid6: using intx1 recovery algorithm
[ 2.173629][ T1] vgaarb: loaded
[ 2.177677][ T1] SCSI subsystem initialized
[ 2.183025][ T1] usbcore: registered new interface driver usbfs
[ 2.189351][ T1] usbcore: registered new interface driver hub
[ 2.195526][ T1] usbcore: registered new device driver usb
[ 2.201923][ T1] media: Linux media interface: v0.10
[ 2.207279][ T1] videodev: Linux video capture interface: v2.00
[ 2.213851][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 2.219548][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 2.229496][ T1] PTP clock support registered
[ 2.235911][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource
[ 2.788420][ T1] VFS: Disk quotas dquot_6.6.0
[ 2.793106][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.813995][ T1] NET: Registered protocol family 2
[ 2.819624][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 2.828043][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 2.835862][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 2.843091][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.850248][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 2.856920][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 2.864204][ T1] NET: Registered protocol family 1
[ 2.869743][ T1] RPC: Registered named UNIX socket transport module.
[ 2.876402][ T1] RPC: Registered udp transport module.
[ 2.881815][ T1] RPC: Registered tcp transport module.
[ 2.887241][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.894399][ T1] PCI: CLS 0 bytes, default 64
[ 2.899389][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 2.906867][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 2.918138][ T1] Initialise system trusted keyrings
[ 2.923317][ T1] Key type blacklist registered
[ 2.928216][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 2.935477][ T1] zbud: loaded
[ 2.939408][ T1] NFS: Registering the id_resolver key type
[ 2.945187][ T1] Key type id_resolver registered
[ 2.950104][ T1] Key type id_legacy registered
[ 2.954830][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 2.962265][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 2.969583][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 2.977787][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 2.985067][ T1] orangefs_init: module version upstream loaded
[ 2.992912][ T1] async_tx: api initialized (async)
[ 2.998009][ T1] Key type asymmetric registered
[ 3.002814][ T1] Asymmetric key parser 'x509' registered
[ 3.008454][ T1] bounce: pool size: 64 pages
[ 3.013100][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[ 3.023930][ T1] armada-xp-pinctrl f1018000.pin-ctrl: registered pinctrl driver
[ 3.034576][ T1] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00
[ 3.042028][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 3.048244][ T1] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff]
[ 3.055836][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 3.062922][ T1] pci 0000:00:01.0: [11ab:7823] type 01 class 0x060400
[ 3.069678][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 3.077553][ T1] pci 0000:00:05.0: [11ab:7823] type 01 class 0x060400
[ 3.084291][ T1] pci 0000:00:05.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 3.092891][ T1] PCI: bus0: Fast back to back transfers disabled
[ 3.099218][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.107967][ T1] pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.116896][ T1] pci 0000:01:00.0: [11ab:7042] type 00 class 0x010000
[ 3.123645][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x14000000-0x140fffff 64bit]
[ 3.131180][ T1] pci 0000:01:00.0: reg 0x18: [io 0x0000-0x00ff]
[ 3.137791][ T1] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 3.149633][ T1] PCI: bus1: Fast back to back transfers disabled
[ 3.155946][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 3.163488][ T1] pci 0000:02:00.0: [1b6f:7023] type 00 class 0x0c0330
[ 3.170263][ T1] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[ 3.177819][ T1] pci 0000:02:00.0: enabling Extended Tags
[ 3.183563][ T1] pci 0000:02:00.0: supports D1 D2
[ 3.188557][ T1] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot
[ 3.195545][ T1] pci 0000:00:05.0: ASPM: current common clock configuration is broken, reconfiguring
[ 3.227038][ T1] PCI: bus2: Fast back to back transfers disabled
[ 3.233333][ T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 3.240734][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xf8000000-0xf80fffff]
[ 3.248345][ T1] pci 0000:00:05.0: BAR 14: assigned [mem 0xf8100000-0xf81fffff]
[ 3.255950][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff]
[ 3.263021][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xf8200000-0xf82007ff pref]
[ 3.270974][ T1] pci 0000:00:05.0: BAR 6: assigned [mem 0xf8300000-0xf83007ff pref]
[ 3.278931][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf80fffff 64bit]
[ 3.286979][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10000-0x100ff]
[ 3.293964][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 3.299653][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff]
[ 3.306650][ T1] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff]
[ 3.314162][ T1] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8100000-0xf8107fff 64bit]
[ 3.322209][ T1] pci 0000:00:05.0: PCI bridge to [bus 02]
[ 3.327899][ T1] pci 0000:00:05.0: bridge window [mem 0xf8100000-0xf81fffff]
[ 3.335478][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143)
[ 3.342403][ T1] pcieport 0000:00:05.0: enabling device (0140 -> 0142)
[ 3.349293][ T1] pci 0000:02:00.0: enabling device (0140 -> 0142)
[ 3.356466][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 3.416569][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 3.426483][ T1] mv_xor f10f0900.xor: Marvell shared XOR driver
[ 3.486581][ T1] mv_xor f10f0900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 3.576434][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.585699][ T1] printk: console [ttyS0] disabled
[ 3.610825][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 19, base_baud = 15625000) is a 16550A
[ 3.620596][ T1] printk: console [ttyS0] enabled
[ 3.620596][ T1] printk: console [ttyS0] enabled
[ 3.630397][ T1] printk: bootconsole [earlycon0] disabled
[ 3.630397][ T1] printk: bootconsole [earlycon0] disabled
[ 3.662807][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 20, base_baud = 15625000) is a 16550A
[ 3.674334][ T1] sata_mv 0000:01:00.0: enabling device (0140 -> 0143)
[ 3.681193][ T1] sata_mv 0000:01:00.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[ 3.692145][ T1] scsi host0: sata_mv
[ 3.696593][ T1] scsi host1: sata_mv
[ 3.700978][ T1] scsi host2: sata_mv
[ 3.705355][ T1] scsi host3: sata_mv
[ 3.709572][ T1] ata1: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8022000 irq 41
[ 3.717977][ T1] ata2: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8024000 irq 41
[ 3.726369][ T1] ata3: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8026000 irq 41
[ 3.734745][ T1] ata4: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8028000 irq 41
[ 3.744907][ T1] m25p80 spi0.0: n25q064 (8192 Kbytes)
[ 3.750311][ T1] 6 fixed-partitions partitions found on MTD device spi0.0
[ 3.757395][ T1] Creating 6 MTD partitions on "spi0.0":
[ 3.762906][ T1] 0x000000000000-0x0000000d0000 : "RedBoot"
[ 3.769718][ T1] 0x0000000d0000-0x0000003a0000 : "zImage"
[ 3.776473][ T1] 0x0000003a0000-0x0000007d0000 : "rd.gz"
[ 3.783065][ T1] 0x0000007d0000-0x0000007e0000 : "vendor"
[ 3.789771][ T1] 0x0000007e0000-0x0000007f0000 : "RedBoot config"
[ 3.797166][ T1] 0x0000007f0000-0x000000800000 : "FIS directory"
[ 3.805409][ T1] libphy: Fixed MDIO Bus: probed
[ 3.810984][ T1] libphy: orion_mdio_bus: probed
[ 3.818849][ T1] mvneta f1070000.ethernet eth0: Using hardware mac address 6a:8f:6a:eb:21:ea
[ 3.829062][ T1] mvneta f1074000.ethernet eth1: Using hardware mac address b2:69:e6:99:9b:b6
[ 3.838141][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.845404][ T1] ehci-pci: EHCI PCI platform driver
[ 3.850656][ T1] ehci-orion: EHCI orion driver
[ 3.855509][ T1] orion-ehci f1050000.usb: EHCI Host Controller
[ 3.861663][ T1] orion-ehci f1050000.usb: new USB bus registered, assigned bus number 1
[ 3.870061][ T1] orion-ehci f1050000.usb: irq 26, io mem 0xf1050000
[ 3.915933][ T1] orion-ehci f1050000.usb: USB 2.0 started, EHCI 1.00
[ 3.922788][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[ 3.931803][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.939758][ T1] usb usb1: Product: EHCI Host Controller
[ 3.945349][ T1] usb usb1: Manufacturer: Linux 5.2.9-mvebu-tld-1 ehci_hcd
[ 3.952431][ T1] usb usb1: SerialNumber: f1050000.usb
[ 3.958217][ T1] hub 1-0:1.0: USB hub found
[ 3.962714][ T1] hub 1-0:1.0: 1 port detected
[ 3.967988][ T1] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 3.973940][ T1] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2
[ 3.982181][ T1] xhci_hcd 0000:02:00.0: hcc params 0x040040a5 hci version 0x100 quirks 0x0000000000080490
[ 3.992522][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[ 4.001565][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.009524][ T1] usb usb2: Product: xHCI Host Controller
[ 4.015114][ T1] usb usb2: Manufacturer: Linux 5.2.9-mvebu-tld-1 xhci-hcd
[ 4.022196][ T1] usb usb2: SerialNumber: 0000:02:00.0
[ 4.027941][ T1] hub 2-0:1.0: USB hub found
[ 4.032436][ T1] hub 2-0:1.0: 2 ports detected
[ 4.037583][ T1] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 4.043532][ T1] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3
[ 4.051683][ T1] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed
[ 4.058750][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.067398][ T1221] ata1: SATA link down (SStatus 0 SControl 300)
[ 4.067714][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.02
[ 4.082792][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.090756][ T1] usb usb3: Product: xHCI Host Controller
[ 4.096362][ T1] usb usb3: Manufacturer: Linux 5.2.9-mvebu-tld-1 xhci-hcd
[ 4.103431][ T1] usb usb3: SerialNumber: 0000:02:00.0
[ 4.109297][ T1] hub 3-0:1.0: USB hub found
[ 4.113792][ T1] hub 3-0:1.0: 2 ports detected
[ 4.119733][ T1] usbcore: registered new interface driver usblp
[ 4.126113][ T1] usbcore: registered new interface driver usb-storage
[ 4.133289][ T1] mousedev: PS/2 mouse device common for all mice
[ 4.140606][ T1] i2c /dev entries driver
[ 4.148675][ T1] rtc-s35390a 0-0030: registered as rtc0
[ 4.257049][ T1] watchdog: f1020300.watchdog: driver supplied timeout (4294967295) out of range
[ 4.266151][ T1] watchdog: f1020300.watchdog: falling back to default timeout (171)
[ 4.274448][ T1] orion_wdt: Initial timeout 171 sec
[ 4.290214][ T1] device-mapper: uevent: version 1.0.3
[ 4.295790][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[ 4.325302][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 4.332570][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 4.339934][ T23] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 4.341575][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 4.354761][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 4.361610][ T1] device-mapper: raid: Loading target version 1.14.0
[ 4.373100][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 4.381308][ T1] hidraw: raw HID events driver (C) Jiri Kosina
[ 4.387976][ T1] usbcore: registered new interface driver usbhid
[ 4.394264][ T1] usbhid: USB HID core driver
[ 4.399303][ T1] drop_monitor: Initializing network drop monitor service
[ 4.406678][ T1] NET: Registered protocol family 10
[ 4.408390][ T1225] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.418584][ T1] Segment Routing with IPv6
[ 4.423013][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 4.430779][ T1] NET: Registered protocol family 17
[ 4.436139][ T1] 8021q: 802.1Q VLAN Support v1.8
[ 4.441072][ T1] Key type dns_resolver registered
[ 4.446271][ T1] ThumbEE CPU extension supported.
[ 4.451258][ T1] Registering SWP/SWPB emulation handler
[ 4.457272][ T1] registered taskstats version 1
[ 4.462080][ T1] Loading compiled-in X.509 certificates
[ 4.467682][ T1] zswap: loaded using pool lzo/zbud
[ 4.474712][ T1] Key type big_key registered
[ 4.479973][ T1] Key type encrypted registered
[ 4.558221][ T23] usb 1-1: New USB device found, idVendor=18a5, idProduct=0240, bcdDevice= 1.00
[ 4.567151][ T23] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.575008][ T23] usb 1-1: Product: STORE N GO
[ 4.579667][ T23] usb 1-1: Manufacturer: Verbatim
[ 4.584568][ T23] usb 1-1: SerialNumber: 07B21107CD4F328B
[ 4.590846][ T23] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 4.598076][ T23] scsi host4: usb-storage 1-1:1.0
[ 4.747838][ T1229] ata3: SATA link down (SStatus 0 SControl 300)
[ 5.088659][ T1233] ata4: SATA link down (SStatus 0 SControl 300)
[ 5.637701][ T1237] scsi 4:0:0:0: Direct-Access Verbatim STORE N GO PMAP PQ: 0 ANSI: 0 CCS
[ 5.650396][ T7] sd 4:0:0:0: [sda] 15646720 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 5.659264][ T7] sd 4:0:0:0: [sda] Write Protect is off
[ 5.665258][ T7] sd 4:0:0:0: [sda] No Caching mode page found
[ 5.671373][ T7] sd 4:0:0:0: [sda] Assuming drive cache: write through
[ 5.688314][ T7] sda: sda1
[ 5.695015][ T7] sd 4:0:0:0: [sda] Attached SCSI removable disk
[ 25.477669][ T1] rtc-s35390a 0-0030: setting system clock to 2020-04-13T06:46:55 UTC (1586760415)
[ 25.487602][ T1] Waiting 10 sec before mounting root device...
[ 35.716132][ T1] md: Waiting for all devices to be available before autodetect
[ 35.723648][ T1] md: If you don't use raid, use raid=noautodetect
[ 35.730926][ T1] md: Autodetecting RAID arrays.
[ 35.735752][ T1] md: autorun ...
[ 35.739318][ T1] md: ... autorun DONE.
[ 35.770912][ T1] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
[ 35.778896][ T1] VFS: Mounted root (ext4 filesystem) readonly on device 8:1.
[ 35.792534][ C0] random: fast init done
[ 35.813825][ T1] devtmpfs: mounted
[ 35.819501][ T1] Freeing unused kernel memory: 1024K
[ 35.837634][ T1] Checked W+X mappings: passed, no W+X pages found
[ 35.844027][ T1] Run /sbin/init as init process
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
ERROR: could not open /proc/stat: No such file or directory
findfs: unable to resolve 'LABEL=rootfs'
[warn] Files under mount point '/run' will be hidden. ... (warning).
[ ok ] Starting hotplug events dispatcher: systemd-udevd.
[ ok ] Synthesizing the initial hotplug events (subsystems)...done.
[ ok ] Synthesizing the initial hotplug events (devices)...done.
[....] Waiting for /dev to be fully populated...[ 39.267844][ T1739] systemd-udevd[1739]: Using default interface naming scheme 'v240'.
[ 39.284463][ T1733] systemd-udevd[1733]: Using default interface naming scheme 'v240'.
[ 39.363491][ T1733] systemd-udevd[1733]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 39.364472][ T1739] systemd-udevd[1739]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 39.430291][ T1729] systemd-udevd[1729]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 39.430732][ T1736] systemd-udevd[1736]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 39.449490][ T1729] systemd-udevd[1729]: Could not generate persistent MAC address for ip6tnl0: No such file or directory
[ 39.460709][ T1732] systemd-udevd[1732]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 39.618708][ T1730] usbcore: registered new interface driver uas
|
Re: Restore uboot for Synology DS414 April 13, 2020 01:59AM |
Registered: 5 years ago Posts: 48 |
Attempt 2 with initrd loaded
93 % [......................................................................]
95 % [......................................................................]
96 % [......................................................................]
97 % [......................................................................]
99 % [.....................................................]
[Type Ctrl-\ + c to quit]
U-Boot 2019.10-tld-1 (Apr 09 2020 - 16:26:57 -0700)
SoC: MV78230-B0 at 1333 MHz
I2C: ready
DRAM: 1 GiB (667 MHz, 32-bit, ECC not enabled)
Loading Environment from SPI Flash... SF: Detected n25q064 with page size 256 Bytes, erase size 4 KiB, total 8 MiB
*** Warning - bad CRC, using default environment
In: serial@12000
Out: serial@12000
Err: serial@12000
Model: Synology DS414
Board: DS414
Net:
Warning: ethernet@70000 (eth0) using random MAC address - 6a:8f:6a:eb:21:ea
eth0: ethernet@70000
Warning: ethernet@74000 (eth1) using random MAC address - 92:68:23:d6:4a:66
, eth1: ethernet@74000
starting USB...
Bus usb@50000: USB EHCI 1.00
scanning bus usb@50000 for devices...
USB retry period from the environment: 0 second(s)
2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
SF: Detected n25q064 with page size 256 Bytes, erase size 4 KiB, total 8 MiB
Hit any key to stop autoboot: 0
device 0 offset 0xd0000, size 0x700000
SF: 7340032 bytes @ 0xd0000 Read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
=> ext2ls usb 0:1
<DIR> 4096 .
<DIR> 4096 ..
<DIR> 4096 lost+found
<DIR> 4096 etc
<DIR> 4096 mnt
<DIR> 4096 sbin
<DIR> 4096 root
<DIR> 4096 dev
<DIR> 4096 usr
<DIR> 4096 srv
<DIR> 4096 boot
<DIR> 4096 media
<DIR> 4096 proc
<DIR> 4096 var
<DIR> 4096 run
<DIR> 4096 bin
<DIR> 4096 opt
<DIR> 4096 tmp
<DIR> 4096 lib
<DIR> 4096 home
<DIR> 4096 sys
=> ext2ls usb 0:1 boot/
<DIR> 4096 .
<DIR> 4096 ..
<DIR> 4096 dts
3266081 System.map-5.2.9-mvebu-tld-1
5057632 vmlinuz-5.2.9-mvebu-tld-1
9488554 initrd.img-5.2.9-mvebu-tld-1
9676808 linux-headers-5.2.9-mvebu-tld-1_1.0_armhf.deb
5057632 zImage-5.2.9-mvebu-tld-1
5057632 zImage
9488618 uInitrd
183639 config-5.2.9-mvebu-tld-1
5074784 zImage.fdt
5074848 uImage
=> setenv mtdparts 'mtdparts=spi0.0:832K(u-boot),-(data)'
=> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial'
=> ext2load usb 0:1 8000000 boot/uInitrd
9488618 bytes read in 367 ms (24.7 MiB/s)
=> ext2load usb 0:1 2000000 boot/uImage
5074848 bytes read in 227 ms (21.3 MiB/s)
=> bootm 0x2000000 0x8000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-5.2.9-mvebu-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5074784 Bytes = 4.8 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 08000000 ...
Image Name: initramfs-5.2.9-mvebu-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9488554 Bytes = 9 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image
Loading Ramdisk to 3f23d000, end 3fb498aa ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.2.9-mvebu-tld-1 (root@tldDebianVM) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1)) #1 SMP PREEMPT Mon Aug 19 12:47:39 PDT 2019
[ 0.000000][ T0] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d
[ 0.000000][ T0] CPU: div instructions available: patching division code
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Synology DS414
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writealloc
[ 0.000000][ T0] percpu: Embedded 21 pages/cpu s55244 r8192 d22580 u86016
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000][ T0] Memory: 1014540K/1048576K available (10240K kernel code, 833K rwdata, 2724K rodata, 1024K init, 343K bss, 34036K reserved, 0K cma-reserved, 252876K highmem)
[ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x30c/0x830 with crng_init=0
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000][ T0] Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x1a096b00 -> 0x1a096b02
[ 0.000000][ T0] Aurora cache controller enabled, 16 ways, 1024 kB
[ 0.000000][ T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a096b02
[ 0.000000][ T0] Switching to timer-based delay loop, resolution 40ns
[ 0.000005][ T0] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.008556][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.020795][ T0] Console: colour dummy device 80x30
[ 0.025969][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.037074][ T0] pid_max: default: 32768 minimum: 301
[ 0.042534][ T0] LSM: Security Framework initializing
[ 0.047920][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.055267][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.063495][ T0] *** VALIDATE proc ***
[ 0.067661][ T0] *** VALIDATE cgroup1 ***
[ 0.071959][ T0] *** VALIDATE cgroup2 ***
[ 0.076287][ T0] CPU: Testing write buffer coherency: ok
[ 0.082088][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.140233][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.147382][ T1] mvebu-soc-id: MVEBU SoC ID=0x7823, Rev=0x2
[ 0.153364][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.180195][ T1] rcu: Hierarchical SRCU implementation.
[ 0.220195][ T1] smp: Bringing up secondary CPUs ...
[ 0.280297][ T1] Booting CPU 1
[ 0.284039][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.294135][ T1] smp: Brought up 1 node, 2 CPUs
[ 0.305345][ T1] SMP: Total of 2 processors activated (100.00 BogoMIPS).
[ 0.312339][ T1] CPU: All CPU(s) started in SVC mode.
[ 0.318377][ T1] devtmpfs: initialized
[ 0.325734][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[ 0.334604][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.345186][ T1] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.352156][ T1] xor: measuring software checksum speed
[ 0.450183][ T1] arm4regs : 1290.800 MB/sec
[ 0.550184][ T1] 8regs : 810.000 MB/sec
[ 0.650183][ T1] 32regs : 1146.400 MB/sec
[ 0.655075][ T1] xor: using function: arm4regs (1290.800 MB/sec)
[ 0.661371][ T1] prandom: seed boundary self test passed
[ 0.669265][ T1] prandom: 100 self tests passed
[ 0.674080][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.681359][ T1] NET: Registered protocol family 16
[ 0.686858][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.695018][ T1] audit: initializing netlink subsys (disabled)
[ 0.701309][ T33] audit: type=2000 audit(0.680:1): state=initialized audit_enabled=0 res=1
[ 0.710233][ T1] cpuidle: using governor ladder
[ 0.715065][ T1] cpuidle: using governor menu
[ 0.719900][ T12] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0
[ 0.729667][ T12] hw-breakpoint: CPU 0 failed to disable vector catch
[ 0.736359][ T13] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1
[ 0.950371][ T1] raid6: int32x8 gen() 227 MB/s
[ 1.120306][ T1] raid6: int32x8 xor() 134 MB/s
[ 1.290251][ T1] raid6: int32x4 gen() 206 MB/s
[ 1.460264][ T1] raid6: int32x4 xor() 163 MB/s
[ 1.630370][ T1] raid6: int32x2 gen() 197 MB/s
[ 1.800219][ T1] raid6: int32x2 xor() 210 MB/s
[ 1.970263][ T1] raid6: int32x1 gen() 135 MB/s
[ 2.140278][ T1] raid6: int32x1 xor() 182 MB/s
[ 2.145257][ T1] raid6: using algorithm int32x8 gen() 227 MB/s
[ 2.151378][ T1] raid6: .... xor() 134 MB/s, rmw enabled
[ 2.156965][ T1] raid6: using intx1 recovery algorithm
[ 2.163208][ T1] vgaarb: loaded
[ 2.167001][ T1] SCSI subsystem initialized
[ 2.171867][ T1] usbcore: registered new interface driver usbfs
[ 2.178106][ T1] usbcore: registered new interface driver hub
[ 2.184303][ T1] usbcore: registered new device driver usb
[ 2.190310][ T1] media: Linux media interface: v0.10
[ 2.195584][ T1] videodev: Linux video capture interface: v2.00
[ 2.201899][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 2.207575][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 2.217463][ T1] PTP clock support registered
[ 2.223426][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource
[ 2.775941][ T1] VFS: Disk quotas dquot_6.6.0
[ 2.780627][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.798091][ T1] NET: Registered protocol family 2
[ 2.803833][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 2.812220][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 2.820208][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 2.827565][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.834797][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 2.841445][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 2.848747][ T1] NET: Registered protocol family 1
[ 2.854347][ T1] RPC: Registered named UNIX socket transport module.
[ 2.860981][ T1] RPC: Registered udp transport module.
[ 2.866422][ T1] RPC: Registered tcp transport module.
[ 2.871835][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.879006][ T1] PCI: CLS 0 bytes, default 64
[ 2.883813][ T1] Trying to unpack rootfs image as initramfs...
[ 2.889930][ T1] Unable to handle kernel paging request at virtual address ff23d000
[ 2.897867][ T1] pgd = (ptrval)
[ 2.901277][ T1] [ff23d000] *pgd=00000000
[ 2.905562][ T1] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 2.911584][ T1] Modules linked in:
[ 2.915347][ T1] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.2.9-mvebu-tld-1 #1
[ 2.922935][ T1] Hardware name: Marvell Armada 370/XP (Device Tree)
[ 2.929487][ T1] PC is at unpack_to_rootfs+0x128/0x2f4
[ 2.934903][ T1] LR is at kmem_cache_alloc_trace+0x54/0x1a0
[ 2.940750][ T1] pc : [<c0e02bfc>] lr : [<c02861a4>] psr: 20000113
[ 2.947729][ T1] sp : ef0b1e90 ip : 0000001c fp : c0e6283c
[ 2.953663][ T1] r10: c0fd0650 r9 : c0fb27d0 r8 : 00000000
[ 2.959597][ T1] r7 : 00000000 r6 : ff23d000 r5 : 0090c8aa r4 : c0e63cc8
[ 2.966837][ T1] r3 : 00000000 r2 : 00000000 r1 : ef7d09ec r0 : 00000000
[ 2.974078][ T1] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 2.981928][ T1] Control: 10c5387d Table: 0000406a DAC: 00000051
[ 2.988385][ T1] Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
[ 2.995103][ T1] Stack: (0xef0b1e90 to 0xef0b2000)
[ 3.000169][ T1] 1e80: c0e6283c c0f04d48 c0fae520 c0fd0648
[ 3.009067][ T1] 1ea0: 00000000 00000000 c0e79800 efffcd80 c0e6283c c0f04d48 c0c6ba3d 444f66dc
[ 3.017965][ T1] 1ec0: 00000000 c0fd064c c0fae520 c0fd0648 c0e0322c 00000000 c0e79800 efffcd80
[ 3.026863][ T1] 1ee0: c0e6283c c0e0327c ffffe000 c0fae520 c0f04d48 c01037d8 c0cbb64d c014498c
[ 3.035761][ T1] 1f00: 00000000 ef0b1f00 00000000 c0e00670 c0da7310 0000013c 00000005 00000005
[ 3.044659][ T1] 1f20: 00000000 c0da8bc0 0000013b c0da8bc0 c0e62818 efffcdbb efffcdc7 444f66dc
[ 3.053557][ T1] 1f40: c0e6283c 444f66dc 00000006 c0fae520 00000006 c0fd0600 c0e62830 c0fd0600
[ 3.062454][ T1] 1f60: c0e79800 c0e01284 00000005 00000005 00000000 c0e00670 c0a3af74 0000013c
[ 3.071351][ T1] 1f80: 00000000 00000000 c0a3af74 00000000 00000000 00000000 00000000 00000000
[ 3.080249][ T1] 1fa0: 00000000 c0a3af7c 00000000 c01010e8 00000000 00000000 00000000 00000000
[ 3.089146][ T1] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 3.098043][ T1] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[ 3.106949][ T1] [<c0e02bfc>] (unpack_to_rootfs) from [<c0e0327c>] (populate_rootfs+0x50/0xbc)
[ 3.115850][ T1] [<c0e0327c>] (populate_rootfs) from [<c01037d8>] (do_one_initcall+0xe4/0x26c)
[ 3.124750][ T1] [<c01037d8>] (do_one_initcall) from [<c0e01284>] (kernel_init_freeable+0x364/0x3bc)
[ 3.134174][ T1] [<c0e01284>] (kernel_init_freeable) from [<c0a3af7c>] (kernel_init+0x8/0x10c)
[ 3.143073][ T1] [<c0a3af7c>] (kernel_init) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
[ 3.151358][ T1] Exception stack(0xef0b1fb0 to 0xef0b1ff8)
[ 3.157120][ T1] 1fa0: 00000000 00000000 00000000 00000000
[ 3.166017][ T1] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 3.174913][ T1] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 3.182244][ T1] Code: 0a000064 ebcc9032 e1c421d0 e1cd21f0 (e5d63000)
[ 3.189055][ T1] ---[ end trace b4f8607050bccde7 ]---
[ 3.194466][ T1] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 3.202847][ C1] CPU1: stopping
[ 3.206263][ C1] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G D 5.2.9-mvebu-tld-1 #1
[ 3.215245][ C1] Hardware name: Marvell Armada 370/XP (Device Tree)
[ 3.221802][ C1] [<c0117684>] (unwind_backtrace) from [<c0112034>] (show_stack+0x10/0x14)
[ 3.230267][ C1] [<c0112034>] (show_stack) from [<c0a258a8>] (dump_stack+0x70/0x8c)
[ 3.238211][ C1] [<c0a258a8>] (dump_stack) from [<c0115338>] (handle_IPI+0x2b8/0x3d4)
[ 3.246330][ C1] [<c0115338>] (handle_IPI) from [<c05a2024>] (armada_370_xp_handle_irq+0x8c/0xa0)
[ 3.255490][ C1] [<c05a2024>] (armada_370_xp_handle_irq) from [<c01021cc>] (__irq_svc+0x6c/0xa8)
[ 3.264558][ C1] Exception stack(0xef0cff68 to 0xef0cffb0)
[ 3.270322][ C1] ff60: 00000000 0000089c ef7e34a0 c0120634 00000000 00000000
[ 3.279220][ C1] ff80: c0f04d48 00000002 ffffe000 c0f04dac c0d04d83 00000000 00000000 ef0cffb8
[ 3.288116][ C1] ffa0: c010e8a4 c0154030 60000113 ffffffff
[ 3.293883][ C1] [<c01021cc>] (__irq_svc) from [<c0154030>] (do_idle+0x13c/0x270)
[ 3.301650][ C1] [<c0154030>] (do_idle) from [<c01543f8>] (cpu_startup_entry+0x18/0x1c)
[ 3.309938][ C1] [<c01543f8>] (cpu_startup_entry) from [<00102d6c>] (0x102d6c)
[ 3.317446][ T1] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]---
|
Re: Restore uboot for Synology DS414 April 13, 2020 02:17AM |
Admin Registered: 14 years ago Posts: 19,932 |
bignellrp,
Let's go back to booting with root=/dev/sda1. Meaning don't load uInitrd.
This u-boot does not like the variable mtdparts.
Try again with my modified post above.
https://forum.doozan.com/read.php?3,99414,99774#msg-99774
I've changed this env, and removed the mtdparts env.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Let's go back to booting with root=/dev/sda1. Meaning don't load uInitrd.
This u-boot does not like the variable mtdparts.
Try again with my modified post above.
https://forum.doozan.com/read.php?3,99414,99774#msg-99774
I've changed this env, and removed the mtdparts env.
setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=10 mtdparts=spi0.0:832K(u-boot),-(data) earlyprintk=serial'
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Restore uboot for Synology DS414 April 13, 2020 05:47AM |
Registered: 5 years ago Posts: 48 |
I cant get it to boot with those mtdparts vars....
Do you know how i can load the stock uboot bin from your uboot build without booting into debian?
Edited 2 time(s). Last edit at 04/13/2020 10:39AM by bignellrp.
87 % [......................................................................]
88 % [......................................................................]
90 % [......................................................................]
91 % [......................................................................]
92 % [......................................................................]
93 % [......................................................................]
95 % [......................................................................]
96 % [......................................................................]
97 % [......................................................................]
99 % [.....................................................]
[Type Ctrl-\ + c to quit]
U-Boot 2019.10-tld-1 (Apr 09 2020 - 16:26:57 -0700)
SoC: MV78230-B0 at 1333 MHz
I2C: ready
DRAM: 1 GiB (667 MHz, 32-bit, ECC not enabled)
Loading Environment from SPI Flash... SF: Detected n25q064 with page size 256 Bytes, erase size 4 KiB, total 8 MiB
*** Warning - bad CRC, using default environment
In: serial@12000
Out: serial@12000
Err: serial@12000
Model: Synology DS414
Board: DS414
Net:
Warning: ethernet@70000 (eth0) using random MAC address - 62:68:99:f9:43:29
eth0: ethernet@70000
Warning: ethernet@74000 (eth1) using random MAC address - 92:1d:70:ca:61:12
, eth1: ethernet@74000
starting USB...
Bus usb@50000: USB EHCI 1.00
scanning bus usb@50000 for devices...
USB retry period from the environment: 0 second(s)
2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
SF: Detected n25q064 with page size 256 Bytes, erase size 4 KiB, total 8 MiB
Hit any key to stop autoboot: 0
device 0 offset 0xd0000, size 0x700000
SF: 7340032 bytes @ 0xd0000 Read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
=> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=3 mtdparts=spi0.0:832K(u-boot),-(data) earlyprintk=serial'
=> ext2load usb 0:1 2000000 boot/uImage
5074848 bytes read in 230 ms (21 MiB/s)
=> bootm 0x2000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-5.2.9-mvebu-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5074784 Bytes = 4.8 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.2.9-mvebu-tld-1 (root@tldDebianVM) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1)) #1 SMP PREEMPT Mon Aug 19 12:47:39 PDT 2019
[ 0.000000][ T0] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d
[ 0.000000][ T0] CPU: div instructions available: patching division code
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Synology DS414
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writealloc
[ 0.000000][ T0] percpu: Embedded 21 pages/cpu s55244 r8192 d22580 u86016
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=3 mtdparts=spi0.0:832K(u-boot),-(data) earlyprintk=serial
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000][ T0] Memory: 1023808K/1048576K available (10240K kernel code, 833K rwdata, 2724K rodata, 1024K init, 343K bss, 24768K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x30c/0x830 with crng_init=0
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000][ T0] Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x1a096b00 -> 0x1a096b02
[ 0.000000][ T0] Aurora cache controller enabled, 16 ways, 1024 kB
[ 0.000000][ T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a096b02
[ 0.000000][ T0] Switching to timer-based delay loop, resolution 40ns
[ 0.000005][ T0] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.008556][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.020794][ T0] Console: colour dummy device 80x30
[ 0.025969][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.037074][ T0] pid_max: default: 32768 minimum: 301
[ 0.042534][ T0] LSM: Security Framework initializing
[ 0.047921][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.055268][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.063495][ T0] *** VALIDATE proc ***
[ 0.067662][ T0] *** VALIDATE cgroup1 ***
[ 0.071960][ T0] *** VALIDATE cgroup2 ***
[ 0.076287][ T0] CPU: Testing write buffer coherency: ok
[ 0.082087][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.140231][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.147382][ T1] mvebu-soc-id: MVEBU SoC ID=0x7823, Rev=0x2
[ 0.153364][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.180195][ T1] rcu: Hierarchical SRCU implementation.
[ 0.220195][ T1] smp: Bringing up secondary CPUs ...
[ 0.280296][ T1] Booting CPU 1
[ 0.284037][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.294133][ T1] smp: Brought up 1 node, 2 CPUs
[ 0.305344][ T1] SMP: Total of 2 processors activated (100.00 BogoMIPS).
[ 0.312337][ T1] CPU: All CPU(s) started in SVC mode.
[ 0.318358][ T1] devtmpfs: initialized
[ 0.325705][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[ 0.334558][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.345137][ T1] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.352109][ T1] xor: measuring software checksum speed
[ 0.450183][ T1] arm4regs : 1290.800 MB/sec
[ 0.550184][ T1] 8regs : 810.000 MB/sec
[ 0.650183][ T1] 32regs : 1146.400 MB/sec
[ 0.655075][ T1] xor: using function: arm4regs (1290.800 MB/sec)
[ 0.661372][ T1] prandom: seed boundary self test passed
[ 0.669266][ T1] prandom: 100 self tests passed
[ 0.674081][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.681363][ T1] NET: Registered protocol family 16
[ 0.686862][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.695021][ T1] audit: initializing netlink subsys (disabled)
[ 0.701311][ T33] audit: type=2000 audit(0.680:1): state=initialized audit_enabled=0 res=1
[ 0.710232][ T1] cpuidle: using governor ladder
[ 0.715065][ T1] cpuidle: using governor menu
[ 0.719898][ T12] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0
[ 0.729665][ T12] hw-breakpoint: CPU 0 failed to disable vector catch
[ 0.736358][ T13] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1
[ 0.960456][ T1] raid6: int32x8 gen() 227 MB/s
[ 1.130359][ T1] raid6: int32x8 xor() 134 MB/s
[ 1.300423][ T1] raid6: int32x4 gen() 206 MB/s
[ 1.470240][ T1] raid6: int32x4 xor() 163 MB/s
[ 1.640437][ T1] raid6: int32x2 gen() 197 MB/s
[ 1.810193][ T1] raid6: int32x2 xor() 210 MB/s
[ 1.980252][ T1] raid6: int32x1 gen() 135 MB/s
[ 2.150229][ T1] raid6: int32x1 xor() 182 MB/s
[ 2.155221][ T1] raid6: using algorithm int32x8 gen() 227 MB/s
[ 2.161330][ T1] raid6: .... xor() 134 MB/s, rmw enabled
[ 2.166924][ T1] raid6: using intx1 recovery algorithm
[ 2.173553][ T1] vgaarb: loaded
[ 2.177601][ T1] SCSI subsystem initialized
[ 2.182951][ T1] usbcore: registered new interface driver usbfs
[ 2.189277][ T1] usbcore: registered new interface driver hub
[ 2.195450][ T1] usbcore: registered new device driver usb
[ 2.201850][ T1] media: Linux media interface: v0.10
[ 2.207204][ T1] videodev: Linux video capture interface: v2.00
[ 2.213775][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 2.219472][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 2.229419][ T1] PTP clock support registered
[ 2.235825][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource
[ 2.788352][ T1] VFS: Disk quotas dquot_6.6.0
[ 2.793038][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.813922][ T1] NET: Registered protocol family 2
[ 2.819552][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 2.827972][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 2.835791][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 2.843020][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.850177][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 2.856849][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 2.864129][ T1] NET: Registered protocol family 1
[ 2.869696][ T1] RPC: Registered named UNIX socket transport module.
[ 2.876359][ T1] RPC: Registered udp transport module.
[ 2.881773][ T1] RPC: Registered tcp transport module.
[ 2.887200][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.894358][ T1] PCI: CLS 0 bytes, default 64
[ 2.899351][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 2.906833][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 2.918103][ T1] Initialise system trusted keyrings
[ 2.923284][ T1] Key type blacklist registered
[ 2.928191][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 2.935451][ T1] zbud: loaded
[ 2.939373][ T1] NFS: Registering the id_resolver key type
[ 2.945148][ T1] Key type id_resolver registered
[ 2.950066][ T1] Key type id_legacy registered
[ 2.954791][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 2.962226][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 2.969549][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 2.977755][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 2.985041][ T1] orangefs_init: module version upstream loaded
[ 2.992861][ T1] async_tx: api initialized (async)
[ 2.997958][ T1] Key type asymmetric registered
[ 3.002763][ T1] Asymmetric key parser 'x509' registered
[ 3.008403][ T1] bounce: pool size: 64 pages
[ 3.013046][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[ 3.023873][ T1] armada-xp-pinctrl f1018000.pin-ctrl: registered pinctrl driver
[ 3.034537][ T1] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00
[ 3.041990][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 3.048205][ T1] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff]
[ 3.055796][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 3.062883][ T1] pci 0000:00:01.0: [11ab:7823] type 01 class 0x060400
[ 3.069641][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 3.077519][ T1] pci 0000:00:05.0: [11ab:7823] type 01 class 0x060400
[ 3.084257][ T1] pci 0000:00:05.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 3.092859][ T1] PCI: bus0: Fast back to back transfers disabled
[ 3.099185][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.107935][ T1] pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.116865][ T1] pci 0000:01:00.0: [11ab:7042] type 00 class 0x010000
[ 3.123614][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x14000000-0x140fffff 64bit]
[ 3.131150][ T1] pci 0000:01:00.0: reg 0x18: [io 0x0000-0x00ff]
[ 3.137767][ T1] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 3.149600][ T1] PCI: bus1: Fast back to back transfers disabled
[ 3.155912][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 3.163450][ T1] pci 0000:02:00.0: [1b6f:7023] type 00 class 0x0c0330
[ 3.170224][ T1] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[ 3.177780][ T1] pci 0000:02:00.0: enabling Extended Tags
[ 3.183525][ T1] pci 0000:02:00.0: supports D1 D2
[ 3.188519][ T1] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot
[ 3.195508][ T1] pci 0000:00:05.0: ASPM: current common clock configuration is broken, reconfiguring
[ 3.226949][ T1] PCI: bus2: Fast back to back transfers disabled
[ 3.233243][ T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 3.240645][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xf8000000-0xf80fffff]
[ 3.248256][ T1] pci 0000:00:05.0: BAR 14: assigned [mem 0xf8100000-0xf81fffff]
[ 3.255862][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff]
[ 3.262933][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xf8200000-0xf82007ff pref]
[ 3.270886][ T1] pci 0000:00:05.0: BAR 6: assigned [mem 0xf8300000-0xf83007ff pref]
[ 3.278842][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf80fffff 64bit]
[ 3.286890][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10000-0x100ff]
[ 3.293876][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 3.299565][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff]
[ 3.306561][ T1] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff]
[ 3.314074][ T1] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8100000-0xf8107fff 64bit]
[ 3.322121][ T1] pci 0000:00:05.0: PCI bridge to [bus 02]
[ 3.327811][ T1] pci 0000:00:05.0: bridge window [mem 0xf8100000-0xf81fffff]
[ 3.335396][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143)
[ 3.342321][ T1] pcieport 0000:00:05.0: enabling device (0140 -> 0142)
[ 3.349211][ T1] pci 0000:02:00.0: enabling device (0140 -> 0142)
[ 3.356375][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 3.416523][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 3.426454][ T1] mv_xor f10f0900.xor: Marvell shared XOR driver
[ 3.486533][ T1] mv_xor f10f0900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 3.576522][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.585780][ T1] printk: console [ttyS0] disabled
[ 3.610906][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 19, base_baud = 15625000) is a 16550A
[ 3.620683][ T1] printk: console [ttyS0] enabled
[ 3.620683][ T1] printk: console [ttyS0] enabled
[ 3.630484][ T1] printk: bootconsole [earlycon0] disabled
[ 3.630484][ T1] printk: bootconsole [earlycon0] disabled
[ 3.662901][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 20, base_baud = 15625000) is a 16550A
[ 3.674430][ T1] sata_mv 0000:01:00.0: enabling device (0140 -> 0143)
[ 3.681289][ T1] sata_mv 0000:01:00.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[ 3.692301][ T1] scsi host0: sata_mv
[ 3.696748][ T1] scsi host1: sata_mv
[ 3.701125][ T1] scsi host2: sata_mv
[ 3.705508][ T1] scsi host3: sata_mv
[ 3.709724][ T1] ata1: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8022000 irq 41
[ 3.718128][ T1] ata2: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8024000 irq 41
[ 3.726521][ T1] ata3: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8026000 irq 41
[ 3.734897][ T1] ata4: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8028000 irq 41
[ 3.745158][ T1] m25p80 spi0.0: n25q064 (8192 Kbytes)
[ 3.750528][ T1] 2 cmdlinepart partitions found on MTD device spi0.0
[ 3.757184][ T1] Creating 2 MTD partitions on "spi0.0":
[ 3.762693][ T1] 0x000000000000-0x0000000d0000 : "u-boot"
[ 3.769463][ T1] 0x0000000d0000-0x000000800000 : "data"
[ 3.776946][ T1] libphy: Fixed MDIO Bus: probed
[ 3.782356][ T1] libphy: orion_mdio_bus: probed
[ 3.790163][ T1] mvneta f1070000.ethernet eth0: Using hardware mac address 62:68:99:f9:43:29
[ 3.800392][ T1] mvneta f1074000.ethernet eth1: Using hardware mac address 92:1d:70:ca:61:12
[ 3.809458][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.816741][ T1] ehci-pci: EHCI PCI platform driver
[ 3.821949][ T1] ehci-orion: EHCI orion driver
[ 3.826826][ T1] orion-ehci f1050000.usb: EHCI Host Controller
[ 3.832957][ T1] orion-ehci f1050000.usb: new USB bus registered, assigned bus number 1
[ 3.841351][ T1] orion-ehci f1050000.usb: irq 26, io mem 0xf1050000
[ 3.875846][ T1] orion-ehci f1050000.usb: USB 2.0 started, EHCI 1.00
[ 3.882693][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[ 3.891710][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.899683][ T1] usb usb1: Product: EHCI Host Controller
[ 3.905275][ T1] usb usb1: Manufacturer: Linux 5.2.9-mvebu-tld-1 ehci_hcd
[ 3.912358][ T1] usb usb1: SerialNumber: f1050000.usb
[ 3.918157][ T1] hub 1-0:1.0: USB hub found
[ 3.922650][ T1] hub 1-0:1.0: 1 port detected
[ 3.927922][ T1] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 3.933874][ T1] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2
[ 3.942115][ T1] xhci_hcd 0000:02:00.0: hcc params 0x040040a5 hci version 0x100 quirks 0x0000000000080490
[ 3.952457][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[ 3.961471][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.969429][ T1] usb usb2: Product: xHCI Host Controller
[ 3.975020][ T1] usb usb2: Manufacturer: Linux 5.2.9-mvebu-tld-1 xhci-hcd
[ 3.982103][ T1] usb usb2: SerialNumber: 0000:02:00.0
[ 3.987852][ T1] hub 2-0:1.0: USB hub found
[ 3.992353][ T1] hub 2-0:1.0: 2 ports detected
[ 3.997521][ T1] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 4.003470][ T1] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3
[ 4.011620][ T1] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed
[ 4.018686][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.027641][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.02
[ 4.036733][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.044676][ T1] usb usb3: Product: xHCI Host Controller
[ 4.050288][ T1] usb usb3: Manufacturer: Linux 5.2.9-mvebu-tld-1 xhci-hcd
[ 4.057373][ T1] usb usb3: SerialNumber: 0000:02:00.0
[ 4.063093][ T1] hub 3-0:1.0: USB hub found
[ 4.067301][ T1221] ata1: SATA link down (SStatus 0 SControl 300)
[ 4.067617][ T1] hub 3-0:1.0: 2 ports detected
[ 4.079600][ T1] usbcore: registered new interface driver usblp
[ 4.085979][ T1] usbcore: registered new interface driver usb-storage
[ 4.093161][ T1] mousedev: PS/2 mouse device common for all mice
[ 4.100478][ T1] i2c /dev entries driver
[ 4.108441][ T1] rtc-s35390a 0-0030: registered as rtc0
[ 4.216816][ T1] watchdog: f1020300.watchdog: driver supplied timeout (4294967295) out of range
[ 4.225806][ T1] watchdog: f1020300.watchdog: falling back to default timeout (171)
[ 4.234118][ T1] orion_wdt: Initial timeout 171 sec
[ 4.249973][ T1] device-mapper: uevent: version 1.0.3
[ 4.255534][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[ 4.285039][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 4.292308][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 4.299654][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 4.307016][ T23] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 4.311117][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 4.321314][ T1] device-mapper: raid: Loading target version 1.14.0
[ 4.332789][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 4.341019][ T1] hidraw: raw HID events driver (C) Jiri Kosina
[ 4.347734][ T1] usbcore: registered new interface driver usbhid
[ 4.354049][ T1] usbhid: USB HID core driver
[ 4.359120][ T1] drop_monitor: Initializing network drop monitor service
[ 4.366529][ T1] NET: Registered protocol family 10
[ 4.372596][ T1] Segment Routing with IPv6
[ 4.377106][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 4.385151][ T1] NET: Registered protocol family 17
[ 4.390523][ T1] 8021q: 802.1Q VLAN Support v1.8
[ 4.395478][ T1] Key type dns_resolver registered
[ 4.400685][ T1] ThumbEE CPU extension supported.
[ 4.405696][ T1] Registering SWP/SWPB emulation handler
[ 4.411262][ T1225] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.416453][ T1] registered taskstats version 1
[ 4.422259][ T1] Loading compiled-in X.509 certificates
[ 4.427879][ T1] zswap: loaded using pool lzo/zbud
[ 4.434802][ T1] Key type big_key registered
[ 4.440064][ T1] Key type encrypted registered
[ 4.518134][ T23] usb 1-1: New USB device found, idVendor=18a5, idProduct=0240, bcdDevice= 1.00
[ 4.527065][ T23] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.534923][ T23] usb 1-1: Product: STORE N GO
[ 4.539579][ T23] usb 1-1: Manufacturer: Verbatim
[ 4.544479][ T23] usb 1-1: SerialNumber: 07B21107CD4F328B
[ 4.550770][ T23] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 4.568032][ T23] scsi host4: usb-storage 1-1:1.0
[ 4.757708][ T1229] ata3: SATA link down (SStatus 0 SControl 300)
[ 5.088578][ T1233] ata4: SATA link down (SStatus 0 SControl 300)
[ 5.637417][ T1237] scsi 4:0:0:0: Direct-Access Verbatim STORE N GO PMAP PQ: 0 ANSI: 0 CCS
[ 5.649637][ T7] sd 4:0:0:0: [sda] 15646720 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 5.658678][ T7] sd 4:0:0:0: [sda] Write Protect is off
[ 5.664674][ T7] sd 4:0:0:0: [sda] No Caching mode page found
[ 5.670781][ T7] sd 4:0:0:0: [sda] Assuming drive cache: write through
[ 5.682105][ T7] sda: sda1
[ 5.688802][ T7] sd 4:0:0:0: [sda] Attached SCSI removable disk
[ 25.477573][ T1] rtc-s35390a 0-0030: setting system clock to 2020-04-13T15:12:17 UTC (1586790737)
[ 25.487505][ T1] Waiting 3 sec before mounting root device...
[ 28.516120][ T1] md: Waiting for all devices to be available before autodetect
[ 28.523636][ T1] md: If you don't use raid, use raid=noautodetect
[ 28.530925][ T1] md: Autodetecting RAID arrays.
[ 28.535751][ T1] md: autorun ...
[ 28.539318][ T1] md: ... autorun DONE.
[ 28.572058][ T1] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
[ 28.580021][ T1] VFS: Mounted root (ext4 filesystem) readonly on device 8:1.
[ 28.593950][ C0] random: fast init done
[ 28.614863][ T1] devtmpfs: mounted
[ 28.620529][ T1] Freeing unused kernel memory: 1024K
[ 28.637547][ T1] Checked W+X mappings: passed, no W+X pages found
[ 28.643933][ T1] Run /sbin/init as init process
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
ERROR: could not open /proc/stat: No such file or directory
[warn] Files under mount point '/run' will be hidden. ... (warning).
[ ok ] Starting hotplug events dispatcher: systemd-udevd.
[ ok ] Synthesizing the initial hotplug events (subsystems)...done.
[ ok ] Synthesizing the initial hotplug events (devices)...done.
[....] Waiting for /dev to be fully populated...[ 31.883403][ T1708] systemd-udevd[1708]: Using default interface naming scheme 'v240'.
[ 31.897504][ T1709] systemd-udevd[1709]: Using default interface naming scheme 'v240'.
[ 32.026966][ T1708] systemd-udevd[1708]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 32.047053][ T1724] systemd-udevd[1724]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 32.060529][ T1709] systemd-udevd[1709]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 32.078707][ T1724] systemd-udevd[1724]: Could not generate persistent MAC address for ip6tnl0: No such file or directory
[ 32.099761][ T1714] systemd-udevd[1714]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 32.165980][ T1711] usbcore: registered new interface driver uas
[ 32.193630][ T1712] systemd-udevd[1712]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 32.321631][ T1713] sd 4:0:0:0: Attached scsi generic sg0 type 0
done.
[ ok ] Setting hostname to 'debian'...done.
[ ok ] Activating swap:.
[ 43.220062][ T1920] EXT4-fs (sda1): warning: mounting unchecked fs, running e2fsck is recommended
[ 43.854617][ T1920] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[info] Will now check all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
[ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable..
--HANGS--
Do you know how i can load the stock uboot bin from your uboot build without booting into debian?
Edited 2 time(s). Last edit at 04/13/2020 10:39AM by bignellrp.
|
Re: Restore uboot for Synology DS414 April 13, 2020 10:23AM |
Registered: 5 years ago Posts: 48 |
I tried setting the fstab to /dev/sda1 and disabling the disk check but it still hangs here:
Edited 1 time(s). Last edit at 04/13/2020 10:37AM by bignellrp.
INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. ERROR: could not open /proc/stat: No such file or directory [warn] Files under mount point '/run' will be hidden. ... (warning). [ ok ] Starting hotplug events dispatcher: systemd-udevd. [ ok ] Synthesizing the initial hotplug events (subsystems)...done. [ ok ] Synthesizing the initial hotplug events (devices)...done. [....] Waiting for /dev to be fully populated...[ 31.883403][ T1708] systemd-udevd[1708]: Using default interface naming scheme 'v240'. [ 31.897504][ T1709] systemd-udevd[1709]: Using default interface naming scheme 'v240'. [ 32.026966][ T1708] systemd-udevd[1708]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 32.047053][ T1724] systemd-udevd[1724]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 32.060529][ T1709] systemd-udevd[1709]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 32.078707][ T1724] systemd-udevd[1724]: Could not generate persistent MAC address for ip6tnl0: No such file or directory [ 32.099761][ T1714] systemd-udevd[1714]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 32.165980][ T1711] usbcore: registered new interface driver uas [ 32.193630][ T1712] systemd-udevd[1712]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 32.321631][ T1713] sd 4:0:0:0: Attached scsi generic sg0 type 0 done. [ ok ] Setting hostname to 'debian'...done. [ ok ] Activating swap:. [ 43.220062][ T1920] EXT4-fs (sda1): warning: mounting unchecked fs, running e2fsck is recommended [ 43.854617][ T1920] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [info] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. --HANGS--
Edited 1 time(s). Last edit at 04/13/2020 10:37AM by bignellrp.
|
Re: Restore uboot for Synology DS414 April 13, 2020 10:52AM |
Registered: 5 years ago Posts: 48 |
Ok. I made some progress. I noticed the uboot bin was only 809k so i changed the mtdparts to 810k and i can boot.
But i get permission denied on the flash unlock
root@debian:~# cat /proc/mtd
dev: size erasesize name
mtd0: 000ca800 00001000 "u-boot"
mtd1: 00735800 00001000 "data"
root@debian:~# flash_unlock /dev/mtd0
flash_unlock: error!: could not open: /dev/mtd0
error 13 (Permission denied)
Full serial log below:
But i get permission denied on the flash unlock
root@debian:~# cat /proc/mtd
dev: size erasesize name
mtd0: 000ca800 00001000 "u-boot"
mtd1: 00735800 00001000 "data"
root@debian:~# flash_unlock /dev/mtd0
flash_unlock: error!: could not open: /dev/mtd0
error 13 (Permission denied)
Full serial log below:
93 % [......................................................................]
95 % [......................................................................]
96 % [......................................................................]
97 % [......................................................................]
99 % [.....................................................]
[Type Ctrl-\ + c to quit]
U-Boot 2019.10-tld-1 (Apr 09 2020 - 16:26:57 -0700)
SoC: MV78230-B0 at 1333 MHz
I2C: ready
DRAM: 1 GiB (667 MHz, 32-bit, ECC not enabled)
Loading Environment from SPI Flash... SF: Detected n25q064 with page size 256 Bytes, erase size 4 KiB, total 8 MiB
*** Warning - bad CRC, using default environment
In: serial@12000
Out: serial@12000
Err: serial@12000
Model: Synology DS414
Board: DS414
Net:
Warning: ethernet@70000 (eth0) using random MAC address - 6e:94:77:6e:c7:f6
eth0: ethernet@70000
Warning: ethernet@74000 (eth1) using random MAC address - ea:94:b3:85:20:27
, eth1: ethernet@74000
starting USB...
Bus usb@50000: USB EHCI 1.00
scanning bus usb@50000 for devices...
USB retry period from the environment: 0 second(s)
2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
SF: Detected n25q064 with page size 256 Bytes, erase size 4 KiB, total 8 MiB
Hit any key to stop autoboot: 0
=> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=20 mtdparts=spi0.0:810K(u-boot),-(data) earlyprintk=serial'
=> ext2load usb 0:1 2000000 boot/uImage
5074848 bytes read in 231 ms (21 MiB/s)
=> bootm 0x2000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-5.2.9-mvebu-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5074784 Bytes = 4.8 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.2.9-mvebu-tld-1 (root@tldDebianVM) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1)) #1 SMP PREEMPT Mon Aug 19 12:47:39 PDT 2019
[ 0.000000][ T0] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d
[ 0.000000][ T0] CPU: div instructions available: patching division code
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Synology DS414
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writealloc
[ 0.000000][ T0] percpu: Embedded 21 pages/cpu s55244 r8192 d22580 u86016
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=20 mtdparts=spi0.0:810K(u-boot),-(data) earlyprintk=serial
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000][ T0] Memory: 1023808K/1048576K available (10240K kernel code, 833K rwdata, 2724K rodata, 1024K init, 343K bss, 24768K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x30c/0x830 with crng_init=0
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000][ T0] Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x1a096b00 -> 0x1a096b02
[ 0.000000][ T0] Aurora cache controller enabled, 16 ways, 1024 kB
[ 0.000000][ T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a096b02
[ 0.000000][ T0] Switching to timer-based delay loop, resolution 40ns
[ 0.000005][ T0] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.008557][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.020795][ T0] Console: colour dummy device 80x30
[ 0.025970][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.037075][ T0] pid_max: default: 32768 minimum: 301
[ 0.042536][ T0] LSM: Security Framework initializing
[ 0.047922][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.055269][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.063496][ T0] *** VALIDATE proc ***
[ 0.067661][ T0] *** VALIDATE cgroup1 ***
[ 0.071960][ T0] *** VALIDATE cgroup2 ***
[ 0.076286][ T0] CPU: Testing write buffer coherency: ok
[ 0.082088][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.140232][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.147381][ T1] mvebu-soc-id: MVEBU SoC ID=0x7823, Rev=0x2
[ 0.153363][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.180196][ T1] rcu: Hierarchical SRCU implementation.
[ 0.220196][ T1] smp: Bringing up secondary CPUs ...
[ 0.280298][ T1] Booting CPU 1
[ 0.284040][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.294135][ T1] smp: Brought up 1 node, 2 CPUs
[ 0.305347][ T1] SMP: Total of 2 processors activated (100.00 BogoMIPS).
[ 0.312340][ T1] CPU: All CPU(s) started in SVC mode.
[ 0.318363][ T1] devtmpfs: initialized
[ 0.325719][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[ 0.334593][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.345175][ T1] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.352147][ T1] xor: measuring software checksum speed
[ 0.450184][ T1] arm4regs : 1290.800 MB/sec
[ 0.550185][ T1] 8regs : 810.000 MB/sec
[ 0.650184][ T1] 32regs : 1146.400 MB/sec
[ 0.655076][ T1] xor: using function: arm4regs (1290.800 MB/sec)
[ 0.661373][ T1] prandom: seed boundary self test passed
[ 0.669267][ T1] prandom: 100 self tests passed
[ 0.674082][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.681366][ T1] NET: Registered protocol family 16
[ 0.686863][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.695022][ T1] audit: initializing netlink subsys (disabled)
[ 0.701314][ T33] audit: type=2000 audit(0.680:1): state=initialized audit_enabled=0 res=1
[ 0.710233][ T1] cpuidle: using governor ladder
[ 0.715065][ T1] cpuidle: using governor menu
[ 0.719897][ T12] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0
[ 0.729664][ T12] hw-breakpoint: CPU 0 failed to disable vector catch
[ 0.736357][ T13] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1
[ 0.950394][ T1] raid6: int32x8 gen() 227 MB/s
[ 1.120325][ T1] raid6: int32x8 xor() 134 MB/s
[ 1.290425][ T1] raid6: int32x4 gen() 206 MB/s
[ 1.460243][ T1] raid6: int32x4 xor() 163 MB/s
[ 1.630402][ T1] raid6: int32x2 gen() 197 MB/s
[ 1.800237][ T1] raid6: int32x2 xor() 210 MB/s
[ 1.970256][ T1] raid6: int32x1 gen() 135 MB/s
[ 2.140333][ T1] raid6: int32x1 xor() 183 MB/s
[ 2.145312][ T1] raid6: using algorithm int32x8 gen() 227 MB/s
[ 2.151435][ T1] raid6: .... xor() 134 MB/s, rmw enabled
[ 2.157021][ T1] raid6: using intx1 recovery algorithm
[ 2.163279][ T1] vgaarb: loaded
[ 2.167065][ T1] SCSI subsystem initialized
[ 2.171936][ T1] usbcore: registered new interface driver usbfs
[ 2.178175][ T1] usbcore: registered new interface driver hub
[ 2.184364][ T1] usbcore: registered new device driver usb
[ 2.190374][ T1] media: Linux media interface: v0.10
[ 2.195647][ T1] videodev: Linux video capture interface: v2.00
[ 2.201950][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 2.207626][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 2.217521][ T1] PTP clock support registered
[ 2.231334][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource
[ 2.783889][ T1] VFS: Disk quotas dquot_6.6.0
[ 2.788576][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.806087][ T1] NET: Registered protocol family 2
[ 2.811760][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 2.820148][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 2.828142][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 2.835493][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.842662][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 2.849311][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 2.856608][ T1] NET: Registered protocol family 1
[ 2.862188][ T1] RPC: Registered named UNIX socket transport module.
[ 2.868822][ T1] RPC: Registered udp transport module.
[ 2.874257][ T1] RPC: Registered tcp transport module.
[ 2.879670][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.886841][ T1] PCI: CLS 0 bytes, default 64
[ 2.891828][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 2.899288][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 2.909492][ T1] Initialise system trusted keyrings
[ 2.914708][ T1] Key type blacklist registered
[ 2.919546][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 2.926860][ T1] zbud: loaded
[ 2.940804][ T1] NFS: Registering the id_resolver key type
[ 2.946604][ T1] Key type id_resolver registered
[ 2.951510][ T1] Key type id_legacy registered
[ 2.956235][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 2.963667][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 2.970953][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 2.979120][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 2.986423][ T1] orangefs_init: module version upstream loaded
[ 2.994217][ T1] async_tx: api initialized (async)
[ 2.999287][ T1] Key type asymmetric registered
[ 3.004121][ T1] Asymmetric key parser 'x509' registered
[ 3.009747][ T1] bounce: pool size: 64 pages
[ 3.014367][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[ 3.024282][ T1] armada-xp-pinctrl f1018000.pin-ctrl: registered pinctrl driver
[ 3.033990][ T1] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00
[ 3.041569][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 3.047770][ T1] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff]
[ 3.055384][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 3.062473][ T1] pci 0000:00:01.0: [11ab:7823] type 01 class 0x060400
[ 3.069215][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 3.077000][ T1] pci 0000:00:05.0: [11ab:7823] type 01 class 0x060400
[ 3.083757][ T1] pci 0000:00:05.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 3.092294][ T1] PCI: bus0: Fast back to back transfers disabled
[ 3.098590][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.107346][ T1] pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.116220][ T1] pci 0000:01:00.0: [11ab:7042] type 00 class 0x010000
[ 3.122986][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x14000000-0x140fffff 64bit]
[ 3.130498][ T1] pci 0000:01:00.0: reg 0x18: [io 0x0000-0x00ff]
[ 3.137053][ T1] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 3.148912][ T1] PCI: bus1: Fast back to back transfers disabled
[ 3.155231][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 3.162730][ T1] pci 0000:02:00.0: [1b6f:7023] type 00 class 0x0c0330
[ 3.169481][ T1] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[ 3.177039][ T1] pci 0000:02:00.0: enabling Extended Tags
[ 3.182796][ T1] pci 0000:02:00.0: supports D1 D2
[ 3.187777][ T1] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot
[ 3.194717][ T1] pci 0000:00:05.0: ASPM: current common clock configuration is broken, reconfiguring
[ 3.232442][ T1] PCI: bus2: Fast back to back transfers disabled
[ 3.238737][ T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 3.246138][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xf8000000-0xf80fffff]
[ 3.253752][ T1] pci 0000:00:05.0: BAR 14: assigned [mem 0xf8100000-0xf81fffff]
[ 3.261358][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff]
[ 3.268429][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xf8200000-0xf82007ff pref]
[ 3.276383][ T1] pci 0000:00:05.0: BAR 6: assigned [mem 0xf8300000-0xf83007ff pref]
[ 3.284339][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf80fffff 64bit]
[ 3.292388][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10000-0x100ff]
[ 3.299373][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 3.305063][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff]
[ 3.312059][ T1] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff]
[ 3.319571][ T1] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8100000-0xf8107fff 64bit]
[ 3.327618][ T1] pci 0000:00:05.0: PCI bridge to [bus 02]
[ 3.333309][ T1] pci 0000:00:05.0: bridge window [mem 0xf8100000-0xf81fffff]
[ 3.340893][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143)
[ 3.347814][ T1] pcieport 0000:00:05.0: enabling device (0140 -> 0142)
[ 3.354703][ T1] pci 0000:02:00.0: enabling device (0140 -> 0142)
[ 3.361568][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 3.422046][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 3.431851][ T1] mv_xor f10f0900.xor: Marvell shared XOR driver
[ 3.492034][ T1] mv_xor f10f0900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 3.565894][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.575538][ T1] printk: console [ttyS0] disabled
[ 3.600810][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 19, base_baud = 15625000) is a 16550A
[ 3.610619][ T1] printk: console [ttyS0] enabled
[ 3.610619][ T1] printk: console [ttyS0] enabled
[ 3.620418][ T1] printk: bootconsole [earlycon0] disabled
[ 3.620418][ T1] printk: bootconsole [earlycon0] disabled
[ 3.652790][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 20, base_baud = 15625000) is a 16550A
[ 3.664355][ T1] sata_mv 0000:01:00.0: enabling device (0140 -> 0143)
[ 3.671181][ T1] sata_mv 0000:01:00.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[ 3.682236][ T1] scsi host0: sata_mv
[ 3.686656][ T1] scsi host1: sata_mv
[ 3.691027][ T1] scsi host2: sata_mv
[ 3.695448][ T1] scsi host3: sata_mv
[ 3.699641][ T1] ata1: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8022000 irq 41
[ 3.708044][ T1] ata2: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8024000 irq 41
[ 3.716435][ T1] ata3: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8026000 irq 41
[ 3.724822][ T1] ata4: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8028000 irq 41
[ 3.734977][ T1] m25p80 spi0.0: n25q064 (8192 Kbytes)
[ 3.740317][ T1] 2 cmdlinepart partitions found on MTD device spi0.0
[ 3.746980][ T1] Creating 2 MTD partitions on "spi0.0":
[ 3.752500][ T1] 0x000000000000-0x0000000ca800 : "u-boot"
[ 3.758176][ T1] mtd: partition "u-boot" doesn't end on an erase/write block -- force read-only
[ 3.768325][ T1] 0x0000000ca800-0x000000800000 : "data"
[ 3.773860][ T1] mtd: partition "data" doesn't start on an erase/write block boundary -- force read-only
[ 3.785567][ T1] libphy: Fixed MDIO Bus: probed
[ 3.790988][ T1] libphy: orion_mdio_bus: probed
[ 3.798830][ T1] mvneta f1070000.ethernet eth0: Using hardware mac address 6e:94:77:6e:c7:f6
[ 3.809086][ T1] mvneta f1074000.ethernet eth1: Using hardware mac address ea:94:b3:85:20:27
[ 3.818162][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.825456][ T1] ehci-pci: EHCI PCI platform driver
[ 3.830665][ T1] ehci-orion: EHCI orion driver
[ 3.835537][ T1] orion-ehci f1050000.usb: EHCI Host Controller
[ 3.841686][ T1] orion-ehci f1050000.usb: new USB bus registered, assigned bus number 1
[ 3.850063][ T1] orion-ehci f1050000.usb: irq 26, io mem 0xf1050000
[ 3.881356][ T1] orion-ehci f1050000.usb: USB 2.0 started, EHCI 1.00
[ 3.888215][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[ 3.897229][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.905185][ T1] usb usb1: Product: EHCI Host Controller
[ 3.910776][ T1] usb usb1: Manufacturer: Linux 5.2.9-mvebu-tld-1 ehci_hcd
[ 3.917858][ T1] usb usb1: SerialNumber: f1050000.usb
[ 3.923652][ T1] hub 1-0:1.0: USB hub found
[ 3.928148][ T1] hub 1-0:1.0: 1 port detected
[ 3.933425][ T1] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 3.939379][ T1] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2
[ 3.947627][ T1] xhci_hcd 0000:02:00.0: hcc params 0x040040a5 hci version 0x100 quirks 0x0000000000080490
[ 3.957966][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[ 3.966978][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.974935][ T1] usb usb2: Product: xHCI Host Controller
[ 3.980525][ T1] usb usb2: Manufacturer: Linux 5.2.9-mvebu-tld-1 xhci-hcd
[ 3.987607][ T1] usb usb2: SerialNumber: 0000:02:00.0
[ 3.993393][ T1] hub 2-0:1.0: USB hub found
[ 3.997888][ T1] hub 2-0:1.0: 2 ports detected
[ 4.003034][ T1] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 4.008988][ T1] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3
[ 4.017142][ T1] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed
[ 4.024210][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.033168][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.02
[ 4.042259][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.050201][ T1] usb usb3: Product: xHCI Host Controller
[ 4.055813][ T1] usb usb3: Manufacturer: Linux 5.2.9-mvebu-tld-1 xhci-hcd
[ 4.062828][ T1221] ata1: SATA link down (SStatus 0 SControl 300)
[ 4.062898][ T1] usb usb3: SerialNumber: 0000:02:00.0
[ 4.074900][ T1] hub 3-0:1.0: USB hub found
[ 4.079395][ T1] hub 3-0:1.0: 2 ports detected
[ 4.085288][ T1] usbcore: registered new interface driver usblp
[ 4.091669][ T1] usbcore: registered new interface driver usb-storage
[ 4.098833][ T1] mousedev: PS/2 mouse device common for all mice
[ 4.106216][ T1] i2c /dev entries driver
[ 4.114291][ T1] rtc-s35390a 0-0030: registered as rtc0
[ 4.222503][ T1] watchdog: f1020300.watchdog: driver supplied timeout (4294967295) out of range
[ 4.231605][ T1] watchdog: f1020300.watchdog: falling back to default timeout (171)
[ 4.239911][ T1] orion_wdt: Initial timeout 171 sec
[ 4.255615][ T1] device-mapper: uevent: version 1.0.3
[ 4.261213][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[ 4.270663][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 4.277932][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 4.285277][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 4.292651][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 4.299460][ T1] device-mapper: raid: Loading target version 1.14.0
[ 4.306040][ T49] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 4.317296][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 4.325551][ T1] hidraw: raw HID events driver (C) Jiri Kosina
[ 4.332266][ T1] usbcore: registered new interface driver usbhid
[ 4.338584][ T1] usbhid: USB HID core driver
[ 4.343663][ T1] drop_monitor: Initializing network drop monitor service
[ 4.351022][ T1] NET: Registered protocol family 10
[ 4.357172][ T1] Segment Routing with IPv6
[ 4.361652][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 4.369714][ T1] NET: Registered protocol family 17
[ 4.375085][ T1] 8021q: 802.1Q VLAN Support v1.8
[ 4.380049][ T1] Key type dns_resolver registered
[ 4.385259][ T1] ThumbEE CPU extension supported.
[ 4.390269][ T1] Registering SWP/SWPB emulation handler
[ 4.396626][ T1] registered taskstats version 1
[ 4.401504][ T1225] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.407660][ T1] Loading compiled-in X.509 certificates
[ 4.413254][ T1] zswap: loaded using pool lzo/zbud
[ 4.420731][ T1] Key type big_key registered
[ 4.425980][ T1] Key type encrypted registered
[ 4.523450][ T49] usb 1-1: New USB device found, idVendor=18a5, idProduct=0240, bcdDevice= 1.00
[ 4.532399][ T49] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.540262][ T49] usb 1-1: Product: STORE N GO
[ 4.544924][ T49] usb 1-1: Manufacturer: Verbatim
[ 4.549819][ T49] usb 1-1: SerialNumber: 07B21107CD4F328B
[ 4.555958][ T49] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 4.563288][ T49] scsi host4: usb-storage 1-1:1.0
[ 4.743210][ T1229] ata3: SATA link down (SStatus 0 SControl 300)
[ 5.084069][ T1233] ata4: SATA link down (SStatus 0 SControl 300)
[ 5.623038][ T1237] scsi 4:0:0:0: Direct-Access Verbatim STORE N GO PMAP PQ: 0 ANSI: 0 CCS
[ 5.635864][ T7] sd 4:0:0:0: [sda] 15646720 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 5.645111][ T7] sd 4:0:0:0: [sda] Write Protect is off
[ 5.651133][ T7] sd 4:0:0:0: [sda] No Caching mode page found
[ 5.657237][ T7] sd 4:0:0:0: [sda] Assuming drive cache: write through
[ 5.669195][ T7] sda: sda1
[ 5.675885][ T7] sd 4:0:0:0: [sda] Attached SCSI removable disk
[ 25.463603][ T1] rtc-s35390a 0-0030: setting system clock to 2020-04-13T15:48:00 UTC (1586792880)
[ 25.473537][ T1] Waiting 20 sec before mounting root device...
[ 45.941513][ T1] md: Waiting for all devices to be available before autodetect
[ 45.949029][ T1] md: If you don't use raid, use raid=noautodetect
[ 45.956687][ T1] md: Autodetecting RAID arrays.
[ 45.961575][ T1] md: autorun ...
[ 45.965088][ T1] md: ... autorun DONE.
[ 45.996269][ T1] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
[ 46.004237][ T1] VFS: Mounted root (ext4 filesystem) readonly on device 8:1.
[ 46.017911][ C0] random: fast init done
[ 46.039075][ T1] devtmpfs: mounted
[ 46.044731][ T1] Freeing unused kernel memory: 1024K
[ 46.063053][ T1] Checked W+X mappings: passed, no W+X pages found
[ 46.069447][ T1] Run /sbin/init as init process
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
ERROR: could not open /proc/stat: No such file or directory
[warn] Files under mount point '/run' will be hidden. ... (warning).
[ ok ] Starting hotplug events dispatcher: systemd-udevd.
[ ok ] Synthesizing the initial hotplug events (subsystems)...done.
[ ok ] Synthesizing the initial hotplug events (devices)...done.
[....] Waiting for /dev to be fully populated...[ 49.356731][ T1713] systemd-udevd[1713]: Using default interface naming scheme 'v240'.
[ 49.364469][ T1715] systemd-udevd[1715]: Using default interface naming scheme 'v240'.
[ 49.426681][ T1713] systemd-udevd[1713]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 49.446901][ T1715] systemd-udevd[1715]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 49.606814][ T1708] systemd-udevd[1708]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 49.619453][ T1708] systemd-udevd[1708]: Could not generate persistent MAC address for ip6tnl0: No such file or directory
[ 49.623240][ T1714] systemd-udevd[1714]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 49.672717][ T1711] usbcore: registered new interface driver uas
[ 49.674612][ T1716] systemd-udevd[1716]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 49.791261][ T1711] sd 4:0:0:0: Attached scsi generic sg0 type 0
done.
[ ok ] Setting hostname to 'debian'...done.
[ ok ] Activating swap:.
[ 60.761128][ T1920] EXT4-fs (sda1): warning: mounting unchecked fs, running e2fsck is recommended
[ 61.400628][ T1920] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[info] Will now check all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
[ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ 62.814248][ C1] random: crng init done
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Starting Setting kernel variables: sysctl.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...[ 64.805788][ T2446] mvneta f1070000.ethernet eth0: PHY [f1072004.mdio-mii:01] driver [Marvell 88E1510]
[ 64.815571][ T2446] mvneta f1070000.ethernet eth0: configuring for phy/rgmii-id link mode
[ 68.982264][ T23] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 68.990845][ T23] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2667 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2694 (klogd)
. ok
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[....] Running local boot scripts (/etc/rc.local)Warning: Bad CRC, using default environment
Warning: Bad CRC, using default environment
[ 78.235036][ T2901] Setting Persistent MAC address to 00:00:11:22:33:44
<13>Apr 13 08:48:53 root[2908]: Setting Persistent MAC address to 00:00:11:22:33:44
[ 78.333823][ T23] mvneta f1070000.ethernet eth0: Link is Down
[ 78.487613][ T2941] mvneta f1070000.ethernet eth0: PHY [f1072004.mdio-mii:01] driver [Marvell 88E1510]
[ 78.497357][ T2941] mvneta f1070000.ethernet eth0: configuring for phy/rgmii-id link mode
[ 82.665643][ T49] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 82.674225][ T49] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
. ok
Debian GNU/Linux 10 debian ttyS0
debian login: root
Password:
Last login: Mon Apr 13 08:18:34 PDT 2020 on ttyS0
Linux debian 5.2.9-mvebu-tld-1 #1 SMP PREEMPT Mon Aug 19 12:47:39 PDT 2019 armv7l
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
debian
192.168.0.37
Synology DS414
Linux version 5.2.9-mvebu-tld-1 (root@tldDebianVM) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1)) #1 SMP PREEMPT Mon Aug 19 12:47:39 PDT 2019
Debian 10.0
Mon Apr 13 08:49:04 PDT 2020 up 1 minute
root@debian:~# cat /proc/mtd
dev: size erasesize name
mtd0: 000ca800 00001000 "u-boot"
mtd1: 00735800 00001000 "data"
root@debian:~# flash_unlock /dev/mtd0
flash_unlock: error!: could not open: /dev/mtd0
error 13 (Permission denied)
root@debian:~#
|
Re: Restore uboot for Synology DS414 April 13, 2020 01:11PM |
Registered: 5 years ago Posts: 48 |
I think i see the problem now. Its complaining the value is not on the boundry as i didnt choose a value that was a multiple of 64 bytes
If the original cat /proc/mtd showed "000d0000" then a hex to decimal conversion is 851968. Can you set it in bytes?
mtd0: 000d0000 00001000 "RedBoot"
e.g
setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=20 mtdparts=spi0.0:851968B(u-boot),-(data) earlyprintk=serial'
Edited 1 time(s). Last edit at 04/13/2020 01:11PM by bignellrp.
[ 3.746980][ T1] Creating 2 MTD partitions on "spi0.0": [ 3.752500][ T1] 0x000000000000-0x0000000ca800 : "u-boot" [ 3.758176][ T1] mtd: partition "u-boot" doesn't end on an erase/write block -- force read-only [ 3.768325][ T1] 0x0000000ca800-0x000000800000 : "data" [ 3.773860][ T1] mtd: partition "data" doesn't start on an erase/write block boundary -- force read-only
If the original cat /proc/mtd showed "000d0000" then a hex to decimal conversion is 851968. Can you set it in bytes?
mtd0: 000d0000 00001000 "RedBoot"
e.g
setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=20 mtdparts=spi0.0:851968B(u-boot),-(data) earlyprintk=serial'
Edited 1 time(s). Last edit at 04/13/2020 01:11PM by bignellrp.
|
Re: Restore uboot for Synology DS414 April 13, 2020 01:20PM |
Registered: 5 years ago Posts: 48 |
|
Re: Restore uboot for Synology DS414 April 13, 2020 01:27PM |
Registered: 5 years ago Posts: 48 |
Got it. You have to specify the exact amount in bytes without the B
90 % [......................................................................]
91 % [......................................................................]
92 % [......................................................................]
93 % [......................................................................]
95 % [......................................................................]
96 % [......................................................................]
97 % [......................................................................]
99 % [.....................................................]
[Type Ctrl-\ + c to quit]
U-Boot 2019.10-tld-1 (Apr 09 2020 - 16:26:57 -0700)
SoC: MV78230-B0 at 1333 MHz
I2C: ready
DRAM: 1 GiB (667 MHz, 32-bit, ECC not enabled)
Loading Environment from SPI Flash... SF: Detected n25q064 with page size 256 Bytes, erase size 4 KiB, total 8 MiB
*** Warning - bad CRC, using default environment
In: serial@12000
Out: serial@12000
Err: serial@12000
Model: Synology DS414
Board: DS414
Net:
Warning: ethernet@70000 (eth0) using random MAC address - 1a:de:3c:37:5e:cd
eth0: ethernet@70000
Warning: ethernet@74000 (eth1) using random MAC address - e2:39:75:0a:35:41
, eth1: ethernet@74000
starting USB...
Bus usb@50000: USB EHCI 1.00
scanning bus usb@50000 for devices...
USB retry period from the environment: 0 second(s)
2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
SF: Detected n25q064 with page size 256 Bytes, erase size 4 KiB, total 8 MiB
Hit any key to stop autoboot: 0
device 0 offset 0xd0000, size 0x700000
SF: 7340032 bytes @ 0xd0000 Read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
=> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=20 mtdparts=spi0.0:851968(u-boot),-(data) earlyprintk=serial'
=> ext2load usb 0:1 2000000 boot/uImage
5074848 bytes read in 231 ms (21 MiB/s)
=> bootm 0x2000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-5.2.9-mvebu-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5074784 Bytes = 4.8 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.2.9-mvebu-tld-1 (root@tldDebianVM) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1)) #1 SMP PREEMPT Mon Aug 19 12:47:39 PDT 2019
[ 0.000000][ T0] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d
[ 0.000000][ T0] CPU: div instructions available: patching division code
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: Synology DS414
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writealloc
[ 0.000000][ T0] percpu: Embedded 21 pages/cpu s55244 r8192 d22580 u86016
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=20 mtdparts=spi0.0:851968(u-boot),-(data) earlyprintk=serial
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000][ T0] Memory: 1023808K/1048576K available (10240K kernel code, 833K rwdata, 2724K rodata, 1024K init, 343K bss, 24768K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x30c/0x830 with crng_init=0
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000][ T0] Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x1a096b00 -> 0x1a096b02
[ 0.000000][ T0] Aurora cache controller enabled, 16 ways, 1024 kB
[ 0.000000][ T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a096b02
[ 0.000000][ T0] Switching to timer-based delay loop, resolution 40ns
[ 0.000005][ T0] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.008556][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.020794][ T0] Console: colour dummy device 80x30
[ 0.025968][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.037074][ T0] pid_max: default: 32768 minimum: 301
[ 0.042534][ T0] LSM: Security Framework initializing
[ 0.047922][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.055268][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.063497][ T0] *** VALIDATE proc ***
[ 0.067663][ T0] *** VALIDATE cgroup1 ***
[ 0.071961][ T0] *** VALIDATE cgroup2 ***
[ 0.076288][ T0] CPU: Testing write buffer coherency: ok
[ 0.082088][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.140233][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.147383][ T1] mvebu-soc-id: MVEBU SoC ID=0x7823, Rev=0x2
[ 0.153364][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.180196][ T1] rcu: Hierarchical SRCU implementation.
[ 0.220195][ T1] smp: Bringing up secondary CPUs ...
[ 0.280297][ T1] Booting CPU 1
[ 0.284040][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.294136][ T1] smp: Brought up 1 node, 2 CPUs
[ 0.305346][ T1] SMP: Total of 2 processors activated (100.00 BogoMIPS).
[ 0.312340][ T1] CPU: All CPU(s) started in SVC mode.
[ 0.318374][ T1] devtmpfs: initialized
[ 0.325727][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[ 0.334587][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.345166][ T1] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.352135][ T1] xor: measuring software checksum speed
[ 0.450184][ T1] arm4regs : 1290.800 MB/sec
[ 0.550185][ T1] 8regs : 810.000 MB/sec
[ 0.650184][ T1] 32regs : 1146.400 MB/sec
[ 0.655076][ T1] xor: using function: arm4regs (1290.800 MB/sec)
[ 0.661373][ T1] prandom: seed boundary self test passed
[ 0.669268][ T1] prandom: 100 self tests passed
[ 0.674082][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.681367][ T1] NET: Registered protocol family 16
[ 0.686865][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.695024][ T1] audit: initializing netlink subsys (disabled)
[ 0.701316][ T33] audit: type=2000 audit(0.680:1): state=initialized audit_enabled=0 res=1
[ 0.710233][ T1] cpuidle: using governor ladder
[ 0.715065][ T1] cpuidle: using governor menu
[ 0.719899][ T12] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0
[ 0.729666][ T12] hw-breakpoint: CPU 0 failed to disable vector catch
[ 0.736358][ T13] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1
[ 0.960396][ T1] raid6: int32x8 gen() 227 MB/s
[ 1.130326][ T1] raid6: int32x8 xor() 134 MB/s
[ 1.300422][ T1] raid6: int32x4 gen() 206 MB/s
[ 1.470239][ T1] raid6: int32x4 xor() 163 MB/s
[ 1.640402][ T1] raid6: int32x2 gen() 197 MB/s
[ 1.810204][ T1] raid6: int32x2 xor() 210 MB/s
[ 1.980254][ T1] raid6: int32x1 gen() 135 MB/s
[ 2.150359][ T1] raid6: int32x1 xor() 182 MB/s
[ 2.155352][ T1] raid6: using algorithm int32x8 gen() 227 MB/s
[ 2.161462][ T1] raid6: .... xor() 134 MB/s, rmw enabled
[ 2.167056][ T1] raid6: using intx1 recovery algorithm
[ 2.173682][ T1] vgaarb: loaded
[ 2.177731][ T1] SCSI subsystem initialized
[ 2.183082][ T1] usbcore: registered new interface driver usbfs
[ 2.189407][ T1] usbcore: registered new interface driver hub
[ 2.195583][ T1] usbcore: registered new device driver usb
[ 2.201984][ T1] media: Linux media interface: v0.10
[ 2.207337][ T1] videodev: Linux video capture interface: v2.00
[ 2.213909][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 2.219605][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 2.229553][ T1] PTP clock support registered
[ 2.235946][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource
[ 2.788408][ T1] VFS: Disk quotas dquot_6.6.0
[ 2.793095][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.813998][ T1] NET: Registered protocol family 2
[ 2.819630][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 2.828049][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 2.835868][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 2.843098][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.850256][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 2.856930][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 2.864214][ T1] NET: Registered protocol family 1
[ 2.869752][ T1] RPC: Registered named UNIX socket transport module.
[ 2.876413][ T1] RPC: Registered udp transport module.
[ 2.881826][ T1] RPC: Registered tcp transport module.
[ 2.887253][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.894411][ T1] PCI: CLS 0 bytes, default 64
[ 2.899393][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 2.906872][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 2.918154][ T1] Initialise system trusted keyrings
[ 2.923337][ T1] Key type blacklist registered
[ 2.928246][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 2.935510][ T1] zbud: loaded
[ 2.939438][ T1] NFS: Registering the id_resolver key type
[ 2.945213][ T1] Key type id_resolver registered
[ 2.950130][ T1] Key type id_legacy registered
[ 2.954856][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 2.962292][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 2.969605][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 2.977811][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 2.985094][ T1] orangefs_init: module version upstream loaded
[ 2.992940][ T1] async_tx: api initialized (async)
[ 2.998040][ T1] Key type asymmetric registered
[ 3.002845][ T1] Asymmetric key parser 'x509' registered
[ 3.008485][ T1] bounce: pool size: 64 pages
[ 3.013132][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[ 3.023955][ T1] armada-xp-pinctrl f1018000.pin-ctrl: registered pinctrl driver
[ 3.034615][ T1] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00
[ 3.042068][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 3.048284][ T1] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff]
[ 3.055875][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 3.062961][ T1] pci 0000:00:01.0: [11ab:7823] type 01 class 0x060400
[ 3.069718][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 3.077598][ T1] pci 0000:00:05.0: [11ab:7823] type 01 class 0x060400
[ 3.084336][ T1] pci 0000:00:05.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[ 3.092941][ T1] PCI: bus0: Fast back to back transfers disabled
[ 3.099261][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.108011][ T1] pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.116942][ T1] pci 0000:01:00.0: [11ab:7042] type 00 class 0x010000
[ 3.123692][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x14000000-0x140fffff 64bit]
[ 3.131234][ T1] pci 0000:01:00.0: reg 0x18: [io 0x0000-0x00ff]
[ 3.137849][ T1] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 3.149680][ T1] PCI: bus1: Fast back to back transfers disabled
[ 3.155993][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 3.163529][ T1] pci 0000:02:00.0: [1b6f:7023] type 00 class 0x0c0330
[ 3.170304][ T1] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[ 3.177860][ T1] pci 0000:02:00.0: enabling Extended Tags
[ 3.183604][ T1] pci 0000:02:00.0: supports D1 D2
[ 3.188598][ T1] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot
[ 3.195588][ T1] pci 0000:00:05.0: ASPM: current common clock configuration is broken, reconfiguring
[ 3.227062][ T1] PCI: bus2: Fast back to back transfers disabled
[ 3.233357][ T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 3.240760][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xf8000000-0xf80fffff]
[ 3.248372][ T1] pci 0000:00:05.0: BAR 14: assigned [mem 0xf8100000-0xf81fffff]
[ 3.255978][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff]
[ 3.263049][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xf8200000-0xf82007ff pref]
[ 3.271003][ T1] pci 0000:00:05.0: BAR 6: assigned [mem 0xf8300000-0xf83007ff pref]
[ 3.278960][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf80fffff 64bit]
[ 3.287008][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10000-0x100ff]
[ 3.293994][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 3.299683][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff]
[ 3.306679][ T1] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff]
[ 3.314192][ T1] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8100000-0xf8107fff 64bit]
[ 3.322239][ T1] pci 0000:00:05.0: PCI bridge to [bus 02]
[ 3.327929][ T1] pci 0000:00:05.0: bridge window [mem 0xf8100000-0xf81fffff]
[ 3.335507][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143)
[ 3.342432][ T1] pcieport 0000:00:05.0: enabling device (0140 -> 0142)
[ 3.349323][ T1] pci 0000:02:00.0: enabling device (0140 -> 0142)
[ 3.356500][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 3.416622][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 3.426539][ T1] mv_xor f10f0900.xor: Marvell shared XOR driver
[ 3.486645][ T1] mv_xor f10f0900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 3.576643][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.585911][ T1] printk: console [ttyS0] disabled
[ 3.611037][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 19, base_baud = 15625000) is a 16550A
[ 3.620809][ T1] printk: console [ttyS0] enabled
[ 3.620809][ T1] printk: console [ttyS0] enabled
[ 3.630608][ T1] printk: bootconsole [earlycon0] disabled
[ 3.630608][ T1] printk: bootconsole [earlycon0] disabled
[ 3.663019][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 20, base_baud = 15625000) is a 16550A
[ 3.674557][ T1] sata_mv 0000:01:00.0: enabling device (0140 -> 0143)
[ 3.681415][ T1] sata_mv 0000:01:00.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[ 3.692367][ T1] scsi host0: sata_mv
[ 3.696812][ T1] scsi host1: sata_mv
[ 3.701201][ T1] scsi host2: sata_mv
[ 3.705578][ T1] scsi host3: sata_mv
[ 3.709797][ T1] ata1: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8022000 irq 41
[ 3.718201][ T1] ata2: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8024000 irq 41
[ 3.726592][ T1] ata3: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8026000 irq 41
[ 3.734968][ T1] ata4: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8028000 irq 41
[ 3.745131][ T1] m25p80 spi0.0: n25q064 (8192 Kbytes)
[ 3.750501][ T1] 2 cmdlinepart partitions found on MTD device spi0.0
[ 3.757150][ T1] Creating 2 MTD partitions on "spi0.0":
[ 3.762659][ T1] 0x000000000000-0x0000000d0000 : "u-boot"
[ 3.769378][ T1] 0x0000000d0000-0x000000800000 : "data"
[ 3.776872][ T1] libphy: Fixed MDIO Bus: probed
[ 3.782684][ T1] libphy: orion_mdio_bus: probed
[ 3.790479][ T1] mvneta f1070000.ethernet eth0: Using hardware mac address 1a:de:3c:37:5e:cd
[ 3.800720][ T1] mvneta f1074000.ethernet eth1: Using hardware mac address e2:39:75:0a:35:41
[ 3.809780][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.817063][ T1] ehci-pci: EHCI PCI platform driver
[ 3.822271][ T1] ehci-orion: EHCI orion driver
[ 3.827145][ T1] orion-ehci f1050000.usb: EHCI Host Controller
[ 3.833275][ T1] orion-ehci f1050000.usb: new USB bus registered, assigned bus number 1
[ 3.841676][ T1] orion-ehci f1050000.usb: irq 26, io mem 0xf1050000
[ 3.875968][ T1] orion-ehci f1050000.usb: USB 2.0 started, EHCI 1.00
[ 3.882816][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[ 3.891833][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.899806][ T1] usb usb1: Product: EHCI Host Controller
[ 3.905397][ T1] usb usb1: Manufacturer: Linux 5.2.9-mvebu-tld-1 ehci_hcd
[ 3.912480][ T1] usb usb1: SerialNumber: f1050000.usb
[ 3.918281][ T1] hub 1-0:1.0: USB hub found
[ 3.922773][ T1] hub 1-0:1.0: 1 port detected
[ 3.928043][ T1] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 3.933995][ T1] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2
[ 3.942237][ T1] xhci_hcd 0000:02:00.0: hcc params 0x040040a5 hci version 0x100 quirks 0x0000000000080490
[ 3.952584][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[ 3.961599][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.969558][ T1] usb usb2: Product: xHCI Host Controller
[ 3.975148][ T1] usb usb2: Manufacturer: Linux 5.2.9-mvebu-tld-1 xhci-hcd
[ 3.982231][ T1] usb usb2: SerialNumber: 0000:02:00.0
[ 3.987982][ T1] hub 2-0:1.0: USB hub found
[ 3.992477][ T1] hub 2-0:1.0: 2 ports detected
[ 3.997646][ T1] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 4.003594][ T1] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3
[ 4.011744][ T1] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed
[ 4.018810][ T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.027764][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.02
[ 4.036856][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.044799][ T1] usb usb3: Product: xHCI Host Controller
[ 4.050411][ T1] usb usb3: Manufacturer: Linux 5.2.9-mvebu-tld-1 xhci-hcd
[ 4.057496][ T1] usb usb3: SerialNumber: 0000:02:00.0
[ 4.063214][ T1] hub 3-0:1.0: USB hub found
[ 4.067425][ T1221] ata1: SATA link down (SStatus 0 SControl 300)
[ 4.067738][ T1] hub 3-0:1.0: 2 ports detected
[ 4.079752][ T1] usbcore: registered new interface driver usblp
[ 4.086138][ T1] usbcore: registered new interface driver usb-storage
[ 4.093314][ T1] mousedev: PS/2 mouse device common for all mice
[ 4.100639][ T1] i2c /dev entries driver
[ 4.108709][ T1] rtc-s35390a 0-0030: registered as rtc0
[ 4.216943][ T1] watchdog: f1020300.watchdog: driver supplied timeout (4294967295) out of range
[ 4.225932][ T1] watchdog: f1020300.watchdog: falling back to default timeout (171)
[ 4.234326][ T1] orion_wdt: Initial timeout 171 sec
[ 4.240156][ T1] device-mapper: uevent: version 1.0.3
[ 4.245715][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[ 4.255189][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 4.262458][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 4.269807][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 4.277181][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 4.283990][ T1] device-mapper: raid: Loading target version 1.14.0
[ 4.295835][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 4.304145][ T1] hidraw: raw HID events driver (C) Jiri Kosina
[ 4.310308][ T23] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 4.317984][ T1] usbcore: registered new interface driver usbhid
[ 4.324387][ T1] usbhid: USB HID core driver
[ 4.329394][ T1] drop_monitor: Initializing network drop monitor service
[ 4.336828][ T1] NET: Registered protocol family 10
[ 4.342933][ T1] Segment Routing with IPv6
[ 4.347420][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 4.355430][ T1] NET: Registered protocol family 17
[ 4.370847][ T1] 8021q: 802.1Q VLAN Support v1.8
[ 4.375775][ T1] Key type dns_resolver registered
[ 4.381028][ T1] ThumbEE CPU extension supported.
[ 4.386088][ T1] Registering SWP/SWPB emulation handler
[ 4.392542][ T1] registered taskstats version 1
[ 4.397399][ T1] Loading compiled-in X.509 certificates
[ 4.402984][ T1] zswap: loaded using pool lzo/zbud
[ 4.408116][ T1225] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.416719][ T1] Key type big_key registered
[ 4.421940][ T1] Key type encrypted registered
[ 4.518210][ T23] usb 1-1: New USB device found, idVendor=18a5, idProduct=0240, bcdDevice= 1.00
[ 4.527160][ T23] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.535018][ T23] usb 1-1: Product: STORE N GO
[ 4.539672][ T23] usb 1-1: Manufacturer: Verbatim
[ 4.544578][ T23] usb 1-1: SerialNumber: 07B21107CD4F328B
[ 4.551023][ T23] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 4.558317][ T23] scsi host4: usb-storage 1-1:1.0
[ 4.737847][ T1229] ata3: SATA link down (SStatus 0 SControl 300)
[ 5.068700][ T1233] ata4: SATA link down (SStatus 0 SControl 300)
[ 5.637497][ T1237] scsi 4:0:0:0: Direct-Access Verbatim STORE N GO PMAP PQ: 0 ANSI: 0 CCS
[ 5.649983][ T20] sd 4:0:0:0: [sda] 15646720 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 5.659225][ T20] sd 4:0:0:0: [sda] Write Protect is off
[ 5.665371][ T20] sd 4:0:0:0: [sda] No Caching mode page found
[ 5.671532][ T20] sd 4:0:0:0: [sda] Assuming drive cache: write through
[ 5.683179][ T20] sda: sda1
[ 5.689622][ T20] sd 4:0:0:0: [sda] Attached SCSI removable disk
[ 25.477795][ T1] rtc-s35390a 0-0030: setting system clock to 2020-04-13T18:22:43 UTC (1586802163)
[ 25.487735][ T1] Waiting 20 sec before mounting root device...
[ 45.956130][ T1] md: Waiting for all devices to be available before autodetect
[ 45.963646][ T1] md: If you don't use raid, use raid=noautodetect
[ 45.970994][ T1] md: Autodetecting RAID arrays.
[ 45.975819][ T1] md: autorun ...
[ 45.979391][ T1] md: ... autorun DONE.
[ 46.010628][ T1] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
[ 46.018604][ T1] VFS: Mounted root (ext4 filesystem) readonly on device 8:1.
[ 46.033028][ C0] random: fast init done
[ 46.052436][ T1] devtmpfs: mounted
[ 46.058068][ T1] Freeing unused kernel memory: 1024K
[ 46.064939][ T1] Checked W+X mappings: passed, no W+X pages found
[ 46.071414][ T1] Run /sbin/init as init process
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
ERROR: could not open /proc/stat: No such file or directory
[warn] Files under mount point '/run' will be hidden. ... (warning).
[ ok ] Starting hotplug events dispatcher: systemd-udevd.
[ ok ] Synthesizing the initial hotplug events (subsystems)...done.
[ ok ] Synthesizing the initial hotplug events (devices)...done.
[....] Waiting for /dev to be fully populated...[ 49.495101][ T1710] systemd-udevd[1710]: Using default interface naming scheme 'v240'.
[ 49.507606][ T1727] systemd-udevd[1727]: Using default interface naming scheme 'v240'.
[ 49.583675][ T1713] systemd-udevd[1713]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 49.584678][ T1715] systemd-udevd[1715]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 49.618376][ T1709] systemd-udevd[1709]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 49.638815][ T1715] systemd-udevd[1715]: Could not generate persistent MAC address for ip6tnl0: No such file or directory
[ 49.666294][ T1727] systemd-udevd[1727]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 49.697098][ T1710] systemd-udevd[1710]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[ 49.848001][ T1712] usbcore: registered new interface driver uas
[ 49.985257][ T1712] sd 4:0:0:0: Attached scsi generic sg0 type 0
done.
[ ok ] Setting hostname to 'debian'...done.
[ ok ] Activating swap:.
[ 60.825368][ T1921] EXT4-fs (sda1): warning: mounting unchecked fs, running e2fsck is recommended
[ 61.495735][ T1921] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[info] Will now check all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
[ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable..
[ 62.625009][ C0] random: crng init done
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Starting Setting kernel variables: sysctl.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...[ 64.577748][ T2447] mvneta f1070000.ethernet eth0: PHY [f1072004.mdio-mii:01] driver [Marvell 88E1510]
[ 64.587519][ T2447] mvneta f1070000.ethernet eth0: configuring for phy/rgmii-id link mode
[ 68.756884][ T1416] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 68.765466][ T1416] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2670 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2697 (klogd)
. ok
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[....] Running local boot scripts (/etc/rc.local)Warning: Bad CRC, using default environment
Warning: Bad CRC, using default environment
[ 77.838438][ T2904] Setting Persistent MAC address to 00:00:11:22:33:44
<13>Apr 13 11:23:35 root[2911]: Setting Persistent MAC address to 00:00:11:22:33:44
[ 77.937960][ T49] mvneta f1070000.ethernet eth0: Link is Down
[ 78.093305][ T2944] mvneta f1070000.ethernet eth0: PHY [f1072004.mdio-mii:01] driver [Marvell 88E1510]
[ 78.103083][ T2944] mvneta f1070000.ethernet eth0: configuring for phy/rgmii-id link mode
[ 82.280415][ T1416] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 82.288999][ T1416] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
. ok
Debian GNU/Linux 10 debian ttyS0
debian login: root
Password:
Last login: Mon Apr 13 08:49:03 PDT 2020 on ttyS0
Linux debian 5.2.9-mvebu-tld-1 #1 SMP PREEMPT Mon Aug 19 12:47:39 PDT 2019 armv7l
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
debian
192.168.0.37
Synology DS414
Linux version 5.2.9-mvebu-tld-1 (root@tldDebianVM) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1)) #1 SMP PREEMPT Mon Aug 19 12:47:39 PDT 2019
Debian 10.0
Mon Apr 13 11:23:45 PDT 2020 up 1 minute
root@debian:~#
root@debian:~#
root@debian:~# ca /proc/mtd
-bash: ca: command not found
root@debian:~# cat /proc/mtd
dev: size erasesize name
mtd0: 000d0000 00001000 "u-boot"
mtd1: 00730000 00001000 "data"
root@debian:~# ls /tmp/
. ..
root@debian:~# ls /tmp/
. ..
root@debian:~# ls
. .bash_history .config .nano .ssh set_persistent_mac_address
.. .bashrc .lesshst .profile myip.get uboot_DS414r1.bin
root@debian:~# flash_unlock /dev/mtd0
root@debian:~# flashcp -v uboot_DS414r1.bin /dev/mtd0
Erasing blocks: 203/203 (100%)
Writing data: 808k/808k (100%)
Verifying data: 808k/808k (100%)
root@debian:~#
root@debian:~#
|
Re: Restore uboot for Synology DS414 April 13, 2020 01:34PM |
Registered: 5 years ago Posts: 48 |
Do the settings live on another partition as its not changed. Still hangs at the same point with the stock uboot.
E.g. do i need to erase mtd4?
root@debian:~# cat /proc/mtd
dev: size erasesize name
mtd0: 000d0000 00001000 "RedBoot"
mtd1: 002d0000 00001000 "zImage"
mtd2: 00430000 00001000 "rd.gz"
mtd3: 00010000 00001000 "vendor"
mtd4: 00010000 00001000 "RedBoot config"
mtd5: 00010000 00001000 "FIS directory"
Edited 1 time(s). Last edit at 04/13/2020 01:38PM by bignellrp.
E.g. do i need to erase mtd4?
root@debian:~# cat /proc/mtd
dev: size erasesize name
mtd0: 000d0000 00001000 "RedBoot"
mtd1: 002d0000 00001000 "zImage"
mtd2: 00430000 00001000 "rd.gz"
mtd3: 00010000 00001000 "vendor"
mtd4: 00010000 00001000 "RedBoot config"
mtd5: 00010000 00001000 "FIS directory"
pi@raspberrypi:~ $ sudo minicom --device /dev/ttyUSB0
Welcome to minicom 2.7
OPTIONS: I18n
Compiled on Apr 22 2017, 09:14:19.
Port /dev/ttyUSB0, 19:29:17
Press CTRL-A Z for help on special keys
BootROM 1.20
Booting from SPI flash
High speed PHY - Version: 2.1.2 (COM-PHY-V20)
Update PEX Device ID 0x78230
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 4.5.0
DDR3 Training Sequence - Ended Successfully
Status = MV_OK
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-SYNO-d7bdf8d-2013-12-11 (Dec 11 2013 - 17:58:54) Marvell version: v2011.12 2013_Q1.2
Board: Synology AXP 78230 4-bay/2-bay
SoC: MV78230 B0
running 2 CPUs
Custom configuration
CPU: Marvell PJ4B (584) v7 (Rev 2) LE
CPU 0
CPU @ 1333 [MHz]
L2 @ 667 [MHz]
TClock @ 250 [MHz]
DDR @ 667 [MHz]
DDR 32Bit Width, FastPath Memory Access
DDR ECC Disabled
DRAM: 1 GiB
Map: Code: 0x3fefb000:0x3ff9f630
BSS: 0x3ffef33c
Stack: 0x3f9eaef8
Heap: 0x3f9eb000:0x3fefb000
MMC: MRVL_MMC: 0
SF: Detected M25P64 with page size 64 KiB, total 8 MiB
PEX 0.0(0): Root Complex Interface, Detected Link X4, GEN 1.1
PEX 1.0(1): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1.1(2): Detected No Link.
PEX 1.2(3): Detected No Link.
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Device Mode
Modules Detected:
Synology Model: DS414r1
Fan Status: Not Good
Fan 1: Good
Fan 2: Not Good
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-SYNO-d7bdf8d-2013-12-11 (Dec 11 2013 - 17:58:54) Marvell version: v2011.12 2013_Q1.2
Board: Synology AXP 78230 4-bay/2-bay
SoC: MV78230 B0
running 2 CPUs
Custom configuration
CPU: Marvell PJ4B (584) v7 (Rev 2) LE
CPU 0
CPU @ 1333 [MHz]
L2 @ 667 [MHz]
TClock @ 250 [MHz]
DDR @ 667 [MHz]
DDR 32Bit Width, FastPath Memory Access
DDR ECC Disabled
DRAM: 1 GiB
Map: Code: 0x3fefb000:0x3ff9f630
BSS: 0x3ffef33c
Stack: 0x3f9eaef8
Heap: 0x3f9eb000:0x3fefb000
MMC: MRVL_MMC: 0
SF: Detected M25P64 with page size 64 KiB, total 8 MiB
PEX 0.0(0): Root Complex Interface, Detected Link X4, GEN 1.1
PEX 1.0(1): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1.1(2): Detected No Link.
PEX 1.2(3): Detected No Link.
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Device Mode
Modules Detected:
Edited 1 time(s). Last edit at 04/13/2020 01:38PM by bignellrp.
|
Re: Restore uboot for Synology DS414 April 13, 2020 05:47PM |
Admin Registered: 14 years ago Posts: 19,932 |
bignellrp,
1. The bootarg mtdparts cannot prevent the kernel booting. If it is bad, the kernel will print error messages like you have above (out of boundary,...). And then ignore it. In this case, you cannot use it later. So that was a red herring. The booting error is most likely becasue of the rootfs.
This was excellent:
2. In previous booting, it showed your rootfs has errors and was fixed automatically during mount. This could have prevented the booting cleanly into Debian. So you want to bring it to the rPi and fix errors with e2fsck. And bring it back.
===========
And then post the entire serial console log here, if you'd like, before you follow the flashing step in my post above (I've edited to add more info).
https://forum.doozan.com/read.php?3,99414,99774#msg-99774
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
1. The bootarg mtdparts cannot prevent the kernel booting. If it is bad, the kernel will print error messages like you have above (out of boundary,...). And then ignore it. In this case, you cannot use it later. So that was a red herring. The booting error is most likely becasue of the rootfs.
This was excellent:
=> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=20 mtdparts=spi0.0:851968(u-boot),-(data) earlyprintk=serial'
[ 3.745131][ T1] m25p80 spi0.0: n25q064 (8192 Kbytes) [ 3.750501][ T1] 2 cmdlinepart partitions found on MTD device spi0.0 [ 3.757150][ T1] Creating 2 MTD partitions on "spi0.0": [ 3.762659][ T1] 0x000000000000-0x0000000d0000 : "u-boot" [ 3.769378][ T1] 0x0000000d0000-0x000000800000 : "data"
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 000d0000 00001000 "u-boot" mtd1: 00730000 00001000 "data"
2. In previous booting, it showed your rootfs has errors and was fixed automatically during mount. This could have prevented the booting cleanly into Debian. So you want to bring it to the rPi and fix errors with e2fsck. And bring it back.
===========
And then post the entire serial console log here, if you'd like, before you follow the flashing step in my post above (I've edited to add more info).
https://forum.doozan.com/read.php?3,99414,99774#msg-99774
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Restore uboot for Synology DS414 April 14, 2020 05:50AM |
Registered: 5 years ago Posts: 48 |
bodhi Wrote:
-------------------------------------------------------
> Restore stock u-boot.
>
> Prerequisite:
>
> Make sure the uboot_DS414r1.bin size is less than
> or equal to 832K. If it is larger, then it will
> not work.
>
> Flashing Steps:
>
> Repeat the kwboot booting. Interrupt serial
> console and
>
>
> And then load and boot
>
>
> Let it boot all the way into Debian. Login, and
> verify the mtds. We want to see 2 partition. And
> the 1st looks like:
>
> cat /proc/mtd
>
> If the mtd0 looks like above, go ahead and flash
>
>
> Note that if flash_unlock give you error, you can
> ignore it. If there is error after flashcp here
> then stop and post the entire serial console
> log until this point.
>
>
> Now if kwboot is still running, it is OK. It runs
> as a normal serial comm terminal too. Or you can
> start picocom/minicom to run a regular serial
> console.
>
> Reboot and let it boot automatically, watch the
> serial console to observe progress. See if stock
> u-boot can run. Interrupt serial console. And see
> if the envs are normal.
>
> Done.
I managed to follow all the steps successfully from your post here: https://forum.doozan.com/read.php?3,99414,99774#msg-99774
So the uboot should be back to stock. But using minicom my Synology still hangs on boot here:
It used to boot the marvell uboot successfully until i changed some of the setenvs and did a save. This was the reason for my original post here on doozan "Re: Restore uboot for Synology DS414" as i thought restoring uboot to stock would erase these settings and i could get back to the stock Marvel uboot prompt and load the stock firmware image.
It seems the uboot settings are stored on a different part of the flash, maybe here : mtd4: 00010000 00001000 "RedBoot config"
You have successfully helped me boot into debian which proves the hardware is ok and have helped me flash mtd0 proving the uboot partition is ok but i still need some help restoring these uboot settings/envs back to default as the stock uboot is hanging before i can interrupt and get to a prompt.
My current thought is that erasing mtd4 would removing these settings and help me back to this prompt although it could make the boot situation worse?
E.g setting the mtdparts to match the default /proc/mtd
mtd0: 000d0000 00001000 "RedBoot" = 0:851968 (000d0000 = 851968)
mtd1: 002d0000 00001000 "zImage" = 851968:3801088 (002d0000 = 2949120) 2949120+851968=3801088
mtd2: 00430000 00001000 "rd.gz" = 3801088:8192000 (00430000 = 4390912) 3801088+4390912=8192000
mtd3: 00010000 00001000 "vendor" = 8192000:8257536 (00010000 = 65536) 8192000+65536=8257536
mtd4: 00010000 00001000 "RedBoot config" = 8257536:8323072 (00010000 = 65536) 8257536+65536=8323072
mtd5: 00010000 00001000 "FIS directory" = 8323072:8388608 (00010000 = 65536) 8323072+65536=8388608
setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=20 mtdparts=spi0.0:0:851968(u-boot),851968:3801088(zimage),3801088:8192000(rd),8192000:8257536(vendor),8257536:8323072(uconfig),8323072:8388608(fis) earlyprintk=serial'
If this boots then run something along the lines of:
nanddump -f /root/usettings -n -l 65536 /dev/mtd4
flash_unlock /dev/mtd4
flash_erase /dev/mtd4
Please correct me if any of this is crazy talk as i completely understand a little bit of knowledge can be dangerous as all of these guesses are just compiled from lots of google searches.
-------------------------------------------------------
> Restore stock u-boot.
>
> Prerequisite:
>
> Make sure the uboot_DS414r1.bin size is less than
> or equal to 832K. If it is larger, then it will
> not work.
>
> Flashing Steps:
>
> Repeat the kwboot booting. Interrupt serial
> console and
>
>
> setenv bootargs 'console=ttyS0,115200 > root=/dev/sda1 rootdelay=10 > mtdparts=spi0.0:832K(u-boot),-(data) > earlyprintk=serial' >>
> And then load and boot
>
>
> ext2load usb 0:1 2000000 boot/uImage >>
> Let it boot all the way into Debian. Login, and
> verify the mtds. We want to see 2 partition. And
> the 1st looks like:
>
> cat /proc/mtd
>
> dev: size erasesize name > mtd0: 000d0000 00001000 "u-boot" >>
> If the mtd0 looks like above, go ahead and flash
>
>
> flash_unlock /dev/mtd0 > flashcp -v uboot_DS414r1.bin /dev/mtd0 >>
> Note that if flash_unlock give you error, you can
> ignore it. If there is error after flashcp here
> then stop and post the entire serial console
> log until this point.
>
>
> Now if kwboot is still running, it is OK. It runs
> as a normal serial comm terminal too. Or you can
> start picocom/minicom to run a regular serial
> console.
>
> Reboot and let it boot automatically, watch the
> serial console to observe progress. See if stock
> u-boot can run. Interrupt serial console. And see
> if the envs are normal.
>
> Done.
I managed to follow all the steps successfully from your post here: https://forum.doozan.com/read.php?3,99414,99774#msg-99774
root@debian:~# flash_unlock /dev/mtd0 root@debian:~# flashcp -v uboot_DS414r1.bin /dev/mtd0 Erasing blocks: 203/203 (100%) Writing data: 808k/808k (100%) Verifying data: 808k/808k (100%) root@debian:~#
So the uboot should be back to stock. But using minicom my Synology still hangs on boot here:
FPU initialized to Run Fast Mode. USB 0: Host Mode USB 1: Host Mode USB 2: Device Mode Modules Detected:
It used to boot the marvell uboot successfully until i changed some of the setenvs and did a save. This was the reason for my original post here on doozan "Re: Restore uboot for Synology DS414" as i thought restoring uboot to stock would erase these settings and i could get back to the stock Marvel uboot prompt and load the stock firmware image.
It seems the uboot settings are stored on a different part of the flash, maybe here : mtd4: 00010000 00001000 "RedBoot config"
You have successfully helped me boot into debian which proves the hardware is ok and have helped me flash mtd0 proving the uboot partition is ok but i still need some help restoring these uboot settings/envs back to default as the stock uboot is hanging before i can interrupt and get to a prompt.
My current thought is that erasing mtd4 would removing these settings and help me back to this prompt although it could make the boot situation worse?
E.g setting the mtdparts to match the default /proc/mtd
mtd0: 000d0000 00001000 "RedBoot" = 0:851968 (000d0000 = 851968)
mtd1: 002d0000 00001000 "zImage" = 851968:3801088 (002d0000 = 2949120) 2949120+851968=3801088
mtd2: 00430000 00001000 "rd.gz" = 3801088:8192000 (00430000 = 4390912) 3801088+4390912=8192000
mtd3: 00010000 00001000 "vendor" = 8192000:8257536 (00010000 = 65536) 8192000+65536=8257536
mtd4: 00010000 00001000 "RedBoot config" = 8257536:8323072 (00010000 = 65536) 8257536+65536=8323072
mtd5: 00010000 00001000 "FIS directory" = 8323072:8388608 (00010000 = 65536) 8323072+65536=8388608
setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=20 mtdparts=spi0.0:0:851968(u-boot),851968:3801088(zimage),3801088:8192000(rd),8192000:8257536(vendor),8257536:8323072(uconfig),8323072:8388608(fis) earlyprintk=serial'
If this boots then run something along the lines of:
nanddump -f /root/usettings -n -l 65536 /dev/mtd4
flash_unlock /dev/mtd4
flash_erase /dev/mtd4
Please correct me if any of this is crazy talk as i completely understand a little bit of knowledge can be dangerous as all of these guesses are just compiled from lots of google searches.
|
Re: Restore uboot for Synology DS414 April 14, 2020 06:15AM |
Registered: 5 years ago Posts: 48 |
It seems nanddump is not supported but dd works. Im not sure it liked my custom mtdparts as none of my labels are shown
[ 3.718159][ T1] m25p80 spi0.0: n25q064 (8192 Kbytes) [ 3.723530][ T1] mtd: partition has size 0 [ 3.727942][ T1] 6 fixed-partitions partitions found on MTD device spi0.0 [ 3.735025][ T1] Creating 6 MTD partitions on "spi0.0": [ 3.740530][ T1] 0x000000000000-0x0000000d0000 : "RedBoot" [ 3.747383][ T1] 0x0000000d0000-0x0000003a0000 : "zImage" [ 3.754105][ T1] 0x0000003a0000-0x0000007d0000 : "rd.gz" [ 3.760679][ T1] 0x0000007d0000-0x0000007e0000 : "vendor" [ 3.767397][ T1] 0x0000007e0000-0x0000007f0000 : "RedBoot config" [ 3.774802][ T1] 0x0000007f0000-0x000000800000 : "FIS directory"
root@debian:~# nanddump -f mtd4 -n -l 65536 /dev/mtd4 MTDFILEMODE: Operation not supported
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 000d0000 00001000 "RedBoot" mtd1: 002d0000 00001000 "zImage" mtd2: 00430000 00001000 "rd.gz" mtd3: 00010000 00001000 "vendor" mtd4: 00010000 00001000 "RedBoot config" mtd5: 00010000 00001000 "FIS directory"
root@debian:~# dd if=/dev/mtd0 of=mtd0 bs=1 count=851968 851968+0 records in 851968+0 records out 851968 bytes (852 kB, 832 KiB) copied, 67.4513 s, 12.6 kB/s root@debian:~# dd if=/dev/mtd4 of=mtd4 bs=1 count=65536 65536+0 records in 65536+0 records out 65536 bytes (66 kB, 64 KiB) copied, 7.10088 s, 9.2 kB/s
|
Re: Restore uboot for Synology DS414 April 14, 2020 05:48PM |
Admin Registered: 14 years ago Posts: 19,932 |
bignellrp,
Excellent!
Yes. It is more likely some envs there were messed up.
nanddump is a tool for NAND flash. This box has SPI flash.
And the flashing for SPI flash must be done with flashcp command. dd is not recommended. dd should only be used to dump a good mtd to a file for backup.
==========
The best way forward:
Don't erase mtd4. Define mtdparts correctly in u-boot, and then in Debian, adjust the envs using a good set of envs from stock. This hopefully could be found by googling the "DS414 boot log". Or from Synology website. If you can find the mtd4 backup file, or a log that shows the stock envs, then it is easy.
Let me look in the new u-boot source code to see if I can find where the envs reside (if it is the same as stock). This is to doublecheck if the mainline u-boot can be used to restore the envs, too.
I will write a few steps later tonight (my timezone is PST), so you will have something to try when you come back here. They are:
- Define the full stock mtdparts env in u-boot bootargs.
- Define the correct envs location in /etc/fw_env.config
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 04/14/2020 06:39PM by bodhi.
Quote
I managed to follow all the steps successfully from your post here: https://forum.doozan.com/read.php?3,99414,99774#msg-99774
root@debian:~# flash_unlock /dev/mtd0
root@debian:~# flashcp -v uboot_DS414r1.bin /dev/mtd0
Erasing blocks: 203/203 (100%)
Writing data: 808k/808k (100%)
Verifying data: 808k/808k (100%)
root@debian:~#
Excellent!
Quote
It seems the uboot settings are stored on a different part of the flash, maybe here : mtd4: 00010000 00001000 "RedBoot config"
Yes. It is more likely some envs there were messed up.
Quote
It seems nanddump is not supported but dd works. Im not sure it liked my custom mtdparts as none of my labels are shown
nanddump is a tool for NAND flash. This box has SPI flash.
And the flashing for SPI flash must be done with flashcp command. dd is not recommended. dd should only be used to dump a good mtd to a file for backup.
==========
The best way forward:
Don't erase mtd4. Define mtdparts correctly in u-boot, and then in Debian, adjust the envs using a good set of envs from stock. This hopefully could be found by googling the "DS414 boot log". Or from Synology website. If you can find the mtd4 backup file, or a log that shows the stock envs, then it is easy.
Let me look in the new u-boot source code to see if I can find where the envs reside (if it is the same as stock). This is to doublecheck if the mainline u-boot can be used to restore the envs, too.
I will write a few steps later tonight (my timezone is PST), so you will have something to try when you come back here. They are:
- Define the full stock mtdparts env in u-boot bootargs.
- Define the correct envs location in /etc/fw_env.config
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 04/14/2020 06:39PM by bodhi.
|
Re: Restore uboot for Synology DS414 April 14, 2020 09:13PM |
Admin Registered: 14 years ago Posts: 19,932 |
1. Define mtdparts in u-boot
There is no need to use decimal notation. We'll just copy the hex value from cat /proc/mtd. And no need to specify offset to run with the new kernel either. Size should be enough.
Therefore,
Boot with this new bootargs.
2. Define fw_env.config
Boot into Debian. And modify fw_env.config.
cat /etc/fw_env.config
And then list the envs
If the envs look sane, then we have defined the mtds correctly, especially mtd4.
Now look at the stock envs listing, and adjust the envs back to stock with fw_setenv. Or,
If the mtd4 stock envs image is available, we can flash it back. Assuming this image is named uboot_DS414_envs.bin,
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
There is no need to use decimal notation. We'll just copy the hex value from cat /proc/mtd. And no need to specify offset to run with the new kernel either. Size should be enough.
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 000d0000 00001000 "RedBoot" mtd1: 002d0000 00001000 "zImage" mtd2: 00430000 00001000 "rd.gz" mtd3: 00010000 00001000 "vendor" mtd4: 00010000 00001000 "RedBoot config" mtd5: 00010000 00001000 "FIS directory"
Therefore,
setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rootdelay=20 mtdparts=spi0.0:0x000d0000(u-boot),0x002d0000(zimage),0x00430000(rd),0x00010000(vendor),0x00010000(u-boot-envs),0x00010000(fis) earlyprintk=serial'
Boot with this new bootargs.
2. Define fw_env.config
Boot into Debian. And modify fw_env.config.
cat /etc/fw_env.config
/dev/mtd4 0x00000 0x10000 0x10000
And then list the envs
fw_printenv
If the envs look sane, then we have defined the mtds correctly, especially mtd4.
Now look at the stock envs listing, and adjust the envs back to stock with fw_setenv. Or,
If the mtd4 stock envs image is available, we can flash it back. Assuming this image is named uboot_DS414_envs.bin,
flash_unlock /dev/mtd4 flashcp -v uboot_DS414_envs.bin /dev/mtd4And then list it to check
fw_printenv
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Restore uboot for Synology DS414 April 15, 2020 03:07AM |
Registered: 5 years ago Posts: 48 |
Thanks. I'll try that in a bit.
Would it help if i get the envs from a working DS214? There is an ebay listing live at the moment. I assume the 214 would be almost identical to the DS414 as they are the same model just 2 disk instead of 4.
I contacted the guy and he is happy to run commands for us. What should i ask him to run?
https://www.ebay.co.uk/itm/274335005779
PS I cant find a file named uboot_DS414_envs.bin in the DS pat package from the synology website but i have a copy of the envs i had before my DS stopped booting.
Would it help if i get the envs from a working DS214? There is an ebay listing live at the moment. I assume the 214 would be almost identical to the DS414 as they are the same model just 2 disk instead of 4.
I contacted the guy and he is happy to run commands for us. What should i ask him to run?
https://www.ebay.co.uk/itm/274335005779
PS I cant find a file named uboot_DS414_envs.bin in the DS pat package from the synology website but i have a copy of the envs i had before my DS stopped booting.
|
Re: Restore uboot for Synology DS414 April 15, 2020 03:23AM |
Admin Registered: 14 years ago Posts: 19,932 |
bignellrp,
> Would it help if i get the envs from a working
> DS214? There is an ebay listing live at the
> moment. I assume the 214 would be almost
> identical to the DS414 as they are the same model
> just 2 disk instead of 4.
>
> I contacted the guy and he is happy to run
> commands for us. What should i ask him to run?
>
> https://www.ebay.co.uk/itm/274335005779
If he can log into stock OS, then
> PS I cant find a file named uboot_DS414_envs.bin
> in the DS pat package from the synology website
That was just an assumed name for that image. Whatever Synology named it, I think they would have that file.
> but i have a copy of the envs i had before my DS
> stopped booting.
That's exactly what we need.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Would it help if i get the envs from a working
> DS214? There is an ebay listing live at the
> moment. I assume the 214 would be almost
> identical to the DS414 as they are the same model
> just 2 disk instead of 4.
>
> I contacted the guy and he is happy to run
> commands for us. What should i ask him to run?
>
> https://www.ebay.co.uk/itm/274335005779
If he can log into stock OS, then
fw_printenv
> PS I cant find a file named uboot_DS414_envs.bin
> in the DS pat package from the synology website
That was just an assumed name for that image. Whatever Synology named it, I think they would have that file.
> but i have a copy of the envs i had before my DS
> stopped booting.
That's exactly what we need.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Restore uboot for Synology DS414 April 15, 2020 05:19AM |
Registered: 5 years ago Posts: 48 |
They certainly dont look right.
Here is the output but it says its on mtd1??
Compared to what it looked like without setting the mtdparts:
I dont think this is correctly printing from mtd4.
Here is the original fw_config i have when it was still booting:
Here is the output but it says its on mtd1??
root@debian:~# cat /proc/mtd
dev: size erasesize name
mtd0: 000d0000 00001000 "u-boot"
mtd1: 002d0000 00001000 "zimage"
mtd2: 00430000 00001000 "rd"
mtd3: 00010000 00001000 "vendor"
mtd4: 00010000 00001000 "u-boot-envs"
mtd5: 00010000 00001000 "fis"
root@debian:~# cat /etc/fw_env.config
# MTD device name Device offset Env. size Flash sector size Number of sectors
/dev/mtd1 0x0000 0x80000 0x20000 4
root@debian:~# fw_printenv
Warning: Bad CRC, using default environment
bootcmd=run distro_bootcmd
bootdelay=2
baudrate=115200
stdin=serial,cros-ec-keyb,usbkbd
stdout=serial,vidconsole
stderr=serial,vidconsole
ethaddr=00:00:11:22:33:44
eth1addr=00:00:11:22:33:45
eth3addr=00:00:11:22:33:46
eth5addr=00:00:11:22:33:47
ipaddr=1.2.3.4
host_boot=if host dev ${devnum}; then setenv devtype host; run scan_dev_for_boot_part; fi
sata_boot=if sata dev ${devnum}; then setenv devtype sata; run scan_dev_for_boot_part; fi
scsi_init=if ${scsi_need_init}; then setenv scsi_need_init false; scsi scan; fi
scsi_boot=run scsi_init; if scsi dev ${devnum}; then setenv devtype scsi; run scan_dev_for_boot_part; fi
virtio_boot=if virtio dev ${devnum}; then setenv devtype virtio; run scan_dev_for_boot_part; fi
boot_prefixes=/ /boot/
boot_scripts=boot.scr.uimg boot.scr
boot_script_dhcp=boot.scr.uimg
boot_targets=host1 host0
boot_syslinux_conf=extlinux/extlinux.conf
boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}${boot_syslinux_conf}
scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${boot_syslinux_conf}; then echo Found ${prefix}${boot_syslinux_conf}; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi
boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}
scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done
scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;
scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done
bootcmd_host1=setenv devnum 1; run host_boot
bootcmd_host0=setenv devnum 0; run host_boot
distro_bootcmd=setenv scsi_need_init; for target in ${boot_targets}; do run bootcmd_${target}; done
bootm_size=0x10000000
kernel_addr_r=0x1000000
fdt_addr_r=0xc00000
ramdisk_addr_r=0x2000000
scriptaddr=0x1000
pxefile_addr_r=0x2000
Compared to what it looked like without setting the mtdparts:
root@debian:~# fw_printenv
Warning: Bad CRC, using default environment
bootcmd=run distro_bootcmd
bootdelay=2
baudrate=115200
stdin=serial,cros-ec-keyb,usbkbd
stdout=serial,vidconsole
stderr=serial,vidconsole
ethaddr=00:00:11:22:33:44
eth1addr=00:00:11:22:33:45
eth3addr=00:00:11:22:33:46
eth5addr=00:00:11:22:33:47
ipaddr=1.2.3.4
host_boot=if host dev ${devnum}; then setenv devtype host; run scan_dev_for_boot_part; fi
sata_boot=if sata dev ${devnum}; then setenv devtype sata; run scan_dev_for_boot_part; fi
scsi_init=if ${scsi_need_init}; then setenv scsi_need_init false; scsi scan; fi
scsi_boot=run scsi_init; if scsi dev ${devnum}; then setenv devtype scsi; run scan_dev_for_boot_part; fi
virtio_boot=if virtio dev ${devnum}; then setenv devtype virtio; run scan_dev_for_boot_part; fi
boot_prefixes=/ /boot/
boot_scripts=boot.scr.uimg boot.scr
boot_script_dhcp=boot.scr.uimg
boot_targets=host1 host0
boot_syslinux_conf=extlinux/extlinux.conf
boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}${boot_syslinux_conf}
scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${boot_syslinux_conf}; then echo Found ${prefix}${boot_syslinux_conf}; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi
boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}
scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done
scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;
scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done
bootcmd_host1=setenv devnum 1; run host_boot
bootcmd_host0=setenv devnum 0; run host_boot
distro_bootcmd=setenv scsi_need_init; for target in ${boot_targets}; do run bootcmd_${target}; done
bootm_size=0x10000000
kernel_addr_r=0x1000000
fdt_addr_r=0xc00000
ramdisk_addr_r=0x2000000
scriptaddr=0x1000
pxefile_addr_r=0x2000
I dont think this is correctly printing from mtd4.
Here is the original fw_config i have when it was still booting:
Marvell>> printenv CASset=min MALLOC_len=5 MPmode=smp amp_enable=no autoload=no baudrate=115200 boot_order=hd_scr hd_img pxe net_img net_scr bootargs=console=ttyS0,115200 ip=off initrd=0x8000040,8M root=/dev/md0 rw syno_hw_version=DS414r1 ihd_num=4 netif_num=2 flash_size=8 SataLedSpecial=1 HddHotplug=1 bootargs_dflt=$console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:DSMP:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=bootm 0xf40d0000 0xf43a0000 bootcmd_auto=stage_boot $boot_order bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootdelay=3 cacheShare=no console=console=ttyS0,115200 device_partition=0:1 disL2Cache=yes disL2Prefetch=yes disaMvPnp=no eeeEnable=no enaAutoRecovery=yes enaClockGating=no enaCpuStream=no enaDCPref=yes enaFPU=yes enaICPref=yes enaLPAE=no enaWrAllo=no eth1addr=00:50:43:02:00:00 eth1mtu=1500 eth2addr=00:50:43:00:00:02 eth2mtu=1500 eth3addr=00:50:43:00:02:02 eth3mtu=1500 ethact=egiga0 ethaddr=00:50:43:02:02:00 ethmtu=1500 ethprime=egiga0 fdt_addr=2040000 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.0.205 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 loadaddr=0x02000000 loads_echo=0 mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:00:00:02 netbsd_en=no netmask=255.255.255.0 netretry=no pcieTune=no pexMode=rc pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rcvrip=169.254.100.100 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=192.168.0.18 setL2CacheWT=no standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usb1Mode=host usb2Mode=device usbActive=0 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 2276/65532 bytes
|
Re: Restore uboot for Synology DS414 April 15, 2020 05:40AM |
Admin Registered: 14 years ago Posts: 19,932 |
bignellrp,
> Here is the output but it says its on mtd1??
mtd1 is the kernel image. So it has nothting to do with u-boot envs.
See my post above:
https://forum.doozan.com/read.php?3,99414,99959#msg-99959
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Here is the output but it says its on mtd1??
mtd1 is the kernel image. So it has nothting to do with u-boot envs.
See my post above:
https://forum.doozan.com/read.php?3,99414,99959#msg-99959
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Restore uboot for Synology DS414 April 15, 2020 05:56AM |
Registered: 5 years ago Posts: 48 |
Yes, but why doesnt it say /dev/mtd4 when i "cat /etc/fw_env.config"
root@debian:~# cat /etc/fw_env.config
# MTD device name Device offset Env. size Flash sector size Number of sectors
/dev/mtd1 0x0000 0x80000 0x20000 4
Maybe i didnt understand your instruction here:
Do you mean vi the config and write it to mtd4? Im confused.
root@debian:~# cat /etc/fw_env.config
# MTD device name Device offset Env. size Flash sector size Number of sectors
/dev/mtd1 0x0000 0x80000 0x20000 4
Maybe i didnt understand your instruction here:
Quote
Boot into Debian. And modify fw_env.config.
cat /etc/fw_env.config
/dev/mtd4 0x00000 0x10000 0x10000
And then list the envs
fw_printenv
Do you mean vi the config and write it to mtd4? Im confused.
|
Re: Restore uboot for Synology DS414 April 15, 2020 06:21AM |
Admin Registered: 14 years ago Posts: 19,932 |
bignellrp,
> Do you mean vi the config and write it to mtd4? Im
> confused.
Yes, sorry I was not clear. Should say "edit the content of the file /etc/fw_env.config" to have
or
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Do you mean vi the config and write it to mtd4? Im
> confused.
Yes, sorry I was not clear. Should say "edit the content of the file /etc/fw_env.config" to have
/dev/mtd4 0x00000 0x10000 0x10000
or
echo "/dev/mtd4 0x00000 0x10000 0x10000" > /etc/fw_env.config
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Restore uboot for Synology DS414 April 15, 2020 07:28AM |
Registered: 5 years ago Posts: 48 |
Looks the same. Did i do something wrong?
Synology DS414
Linux version 5.2.9-mvebu-tld-1 (root@tldDebianVM) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1)) #1 SMP PREEMPT Mon Aug 19 12:47:39 PDT 2019
Debian 10.0
Wed Apr 15 05:22:02 PDT 2020 up 1 minute
root@debian:~# echo "/dev/mtd4 0x00000 0x10000 0x10000"
/dev/mtd4 0x00000 0x10000 0x10000
root@debian:~# cat /etc/fw_env.config
# MTD device name Device offset Env. size Flash sector size Number of sectors
/dev/mtd1 0x0000 0x80000 0x20000 4
root@debian:~# echo "/dev/mtd4 0x00000 0x10000 0x10000" > /etc/fw_env.config
root@debian:~# fw_printenv
Warning: Bad CRC, using default environment
bootcmd=run distro_bootcmd
bootdelay=2
baudrate=115200
stdin=serial,cros-ec-keyb,usbkbd
stdout=serial,vidconsole
stderr=serial,vidconsole
ethaddr=00:00:11:22:33:44
eth1addr=00:00:11:22:33:45
eth3addr=00:00:11:22:33:46
eth5addr=00:00:11:22:33:47
ipaddr=1.2.3.4
host_boot=if host dev ${devnum}; then setenv devtype host; run scan_dev_for_boot_part; fi
sata_boot=if sata dev ${devnum}; then setenv devtype sata; run scan_dev_for_boot_part; fi
scsi_init=if ${scsi_need_init}; then setenv scsi_need_init false; scsi scan; fi
scsi_boot=run scsi_init; if scsi dev ${devnum}; then setenv devtype scsi; run scan_dev_for_boot_part; fi
virtio_boot=if virtio dev ${devnum}; then setenv devtype virtio; run scan_dev_for_boot_part; fi
boot_prefixes=/ /boot/
boot_scripts=boot.scr.uimg boot.scr
boot_script_dhcp=boot.scr.uimg
boot_targets=host1 host0
boot_syslinux_conf=extlinux/extlinux.conf
boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}${boot_syslinux_conf}
scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${boot_syslinux_conf}; then echo Found ${prefix}${boot_syslinux_conf}; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi
boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}
scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done
scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;
scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done
bootcmd_host1=setenv devnum 1; run host_boot
bootcmd_host0=setenv devnum 0; run host_boot
distro_bootcmd=setenv scsi_need_init; for target in ${boot_targets}; do run bootcmd_${target}; done
bootm_size=0x10000000
kernel_addr_r=0x1000000
fdt_addr_r=0xc00000
ramdisk_addr_r=0x2000000
scriptaddr=0x1000
pxefile_addr_r=0x2000
root@debian:~# cat /etc/fw_env.config
/dev/mtd4 0x00000 0x10000 0x10000
|
Re: Restore uboot for Synology DS414 April 15, 2020 12:47PM |
Registered: 5 years ago Posts: 48 |
I've made some progress this evening. I backed up all the mtd parts using dd so thought i would try and reload the stock zImage back to mtd1
The verify gave an error but now the stock uboot boots again and has all the same values.
I can now successfully boot back into the syno software by loading it manually from usb:
usb start
ext2load usb 0:1 8000000 root/rd.bin
ext2load usb 0:1 2000000 root/zImage
bootm 0x2000000 0x8000000
So the last remaining task is to work out what to set in the bootenvs to get it to auto boot again?
Here are the current printenvs:
root@debian:~# flash_unlock /dev/mtd1 root@debian:~# flashcp -v zImage /dev/mtd1 Erasing blocks: 519/519 (100%) Writing data: 2074k/2074k (100%) Verifying data: 2050k/2074k (98%)File does not seem to match flash data. First mismatch at 0x001fe000-0x00200800
The verify gave an error but now the stock uboot boots again and has all the same values.
I can now successfully boot back into the syno software by loading it manually from usb:
usb start
ext2load usb 0:1 8000000 root/rd.bin
ext2load usb 0:1 2000000 root/zImage
bootm 0x2000000 0x8000000
So the last remaining task is to work out what to set in the bootenvs to get it to auto boot again?
Here are the current printenvs:
Modules Detected: Synology Model: DS414r1 Fan Status: Not Good Fan 1: Good Fan 2: Not Good Net: egiga0 [PRIME], egiga1 Press Ctrl+C to abort autoboot in 3 second ## Booting kernel from Legacy Image at f40d0000 ... Image Name: Linux-3.2.40 Created: 2019-05-09 18:48:48 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2123888 Bytes = 2 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... Bad Data CRC ERROR: can't get kernel image! Marvell>> Marvell>> Marvell>> Marvell>> Marvell>> Marvell>> printenv CASset=min MALLOC_len=5 MPmode=smp amp_enable=no autoload=no baudrate=115200 boot_order=hd_scr hd_img pxe net_img net_scr bootargs=console=ttyS0,115200 ip=off initrd=0x8000040,8M root=/dev/md0 rw syno_hw_version=DS414r1 ihd_num=4 netif_num=2 flash_size=8 SataLedSpecial=1 HddHotplug=1 bootargs_dflt=$console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:DSMP:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=bootm 0xf40d0000 0xf43a0000 bootcmd_auto=stage_boot $boot_order bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootdelay=3 cacheShare=no console=console=ttyS0,115200 device_partition=0:1 disL2Cache=yes disL2Prefetch=yes disaMvPnp=no eeeEnable=no enaAutoRecovery=yes enaClockGating=no enaCpuStream=no enaDCPref=yes enaFPU=yes enaICPref=yes enaLPAE=no enaWrAllo=no eth1addr=00:50:43:02:00:00 eth1mtu=1500 eth2addr=00:50:43:00:00:02 eth2mtu=1500 eth3addr=00:50:43:00:02:02 eth3mtu=1500 ethact=egiga0 ethaddr=00:50:43:02:02:00 ethmtu=1500 ethprime=egiga0 fdt_addr=2040000 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=10.4.50.165 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 loadaddr=0x02000000 loads_echo=0 mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:00:00:02 netbsd_en=no netmask=255.255.255.0 netretry=no pcieTune=no pexMode=rc pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rcvrip=169.254.100.100 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=10.4.50.5 setL2CacheWT=no standalone=fsload 0x2000000 $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usb1Mode=host usb2Mode=device usbActive=0 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 2271/65532 bytes Marvell>>
|
Re: Restore uboot for Synology DS414 April 15, 2020 04:06PM |
Registered: 5 years ago Posts: 48 |
Fixed!!
I booted into DSM manually and did a manual update. It rewrote the image itself and now it’s booting again.
Thank you again for all your help. I’ve actually found this fun especially during Corona lockdown. Waking up each morning with a new thing to try to fix my issue and learning lots in the process.
I have started writing a guide showing all the steps I went through which may be useful for others on here. Currently it’s a google doc but happy to add as a forum post if you want it as one of your guides?
I booted into DSM manually and did a manual update. It rewrote the image itself and now it’s booting again.
Thank you again for all your help. I’ve actually found this fun especially during Corona lockdown. Waking up each morning with a new thing to try to fix my issue and learning lots in the process.
I have started writing a guide showing all the steps I went through which may be useful for others on here. Currently it’s a google doc but happy to add as a forum post if you want it as one of your guides?
|
Re: Restore uboot for Synology DS414 April 15, 2020 04:52PM |
Admin Registered: 14 years ago Posts: 19,932 |
bignellrp,
> I booted into DSM manually and did a manual
> update. It rewrote the image itself and now it’s
> booting again.
Awesome!
FYI, after you defined the mtd4 and still see the CRC error, it means that the mtd4 was corrupted. So you cannot list the env without reflashing it, or force it to save so the CRC can be calculated and stored properly.
> I have started writing a guide showing all the
> steps I went through which may be useful for
> others on here. Currently it’s a google doc but
> happy to add as a forum post if you want it as one
> of your guides?
Please do! either in this thread, or create a new thread with title "Debian on Synology DS414" in Debian subforum.
By the way, you are the pioneer for this box, thanks to your testing I can now add this box to the support list for the kernel :)
If your guide will be in this thread, please change the Subject of this thread to "Debian on Synology DS414", so it will be easier for others to find later.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I booted into DSM manually and did a manual
> update. It rewrote the image itself and now it’s
> booting again.
Awesome!
FYI, after you defined the mtd4 and still see the CRC error, it means that the mtd4 was corrupted. So you cannot list the env without reflashing it, or force it to save so the CRC can be calculated and stored properly.
root@debian:~# echo "/dev/mtd4 0x00000 0x10000 0x10000" > /etc/fw_env.config root@debian:~# fw_printenv Warning: Bad CRC, using default environment
> I have started writing a guide showing all the
> steps I went through which may be useful for
> others on here. Currently it’s a google doc but
> happy to add as a forum post if you want it as one
> of your guides?
Please do! either in this thread, or create a new thread with title "Debian on Synology DS414" in Debian subforum.
By the way, you are the pioneer for this box, thanks to your testing I can now add this box to the support list for the kernel :)
If your guide will be in this thread, please change the Subject of this thread to "Debian on Synology DS414", so it will be easier for others to find later.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Restore uboot for Synology DS414 April 16, 2020 01:47PM |
Registered: 5 years ago Posts: 48 |
