Welcome! Log In Create A New Profile

Advanced

openwrt on pogoplug pro v3

Posted by echowarrior108 
openwrt on pogoplug pro v3
October 25, 2020 11:21AM
I currently installed openwrt into nand from the openwrt website, I can post the link if anyone likes as it works well. Feel free to add to this:)

learning is living! Echowarrior108



device pogoplug-pro v3

Debian GNU/Linux bullseye/sid \n \l
Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6) ) #1 SMP PREEMPT Fri Nov 15 04:12:45 PST 2019



Edited 1 time(s). Last edit at 10/25/2020 11:22AM by echowarrior108.
Re: openwrt on pogoplug pro v3
October 25, 2020 11:30AM
my current print env from debian using usb followed by openwrt using nand, the envs are not really cleaned up as this is my alternate (test) pplug.

1:My question from https://forum.doozan.com/read.php?4,86219
Quote

have working openwrt on pogoplug v3 runnning on nand, the trouble I run into is switching from nand to usb boot when I want to run debian from the usb. Here is what I have to do so far and its probably a simple fix.

if I want to run openwrt I have to interrupt boot on serial connection and run the following:
setenv bootcmd 'nboot 60500000 0 440000; bootm'
saveenv 
boot


to run debian usb I have to interrupt boot on serial connection runs run the following:
setenv bootcmd 'run dt_bootcmd_usb'
saveenv
boot


now this will work if I want to always connect to the serial to switch between them however that is cumbersome, how can I set it to run openwrt if no usb and run debian if usb is inserted?

little bit stuck on that! any help would be nice ! Thanks!!



2: also is it possible to move the nand openwrt to a bootable usb so I have more room for the OS?


print env from usb debian:

OX820> printenv
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200n8
bootcmd=run dt_bootcmd_usb
bootcmd_exec=if run load_uimage; then; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
console=console=ttyS0,115200n8
devices=usb ide
dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
dt_load_dtb=ext4load usb 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_load_initrd=ext4load usb 0:1 $uinitrd_addr /boot/uInitrd
dt_load_uimage=ext4load usb 0:1 $uimage_addr /boot/uImage
dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm
dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot
dtb_addr=0x62c00000
dtb_file=/boot/dts/ox820-pogoplug-pro.dtb
ethact=dwmac.40400000
ethaddr=xxxxxxxxxxxx
fileaddr=64000000
filesize=61202a
if_netconsole=ping $serverip
ipaddr=xxxxxxxx
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
preboot_nc=run if_netconsole start_netconsole
serverip=xxxxxxxxxx
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version
stderr=serial
stdin=serial
stdout=serial
uenv_import=echo importing envs ...; env import -t 0x60500000
uenv_init_devices=setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices;  do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x60500000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
uimage_addr=0x60500000
uinitrd_addr=0x60e00000
usb_custom_params=zswap.enabled=1
usb_device=0:1
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10


printenv from openwrt nand:

OX820> printenv
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200n8
bootcmd=nboot 60500000 0 440000; bootm
bootcmd_exec=if run load_uimage; then; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
console=console=ttyS0,115200n8
devices=usb ide
dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
dt_load_dtb=ext4load usb 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_load_initrd=ext4load usb 0:1 $uinitrd_addr /boot/uInitrd
dt_load_uimage=ext4load usb 0:1 $uimage_addr /boot/uImage
dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm
dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot
dtb_addr=0x62c00000
dtb_file=/boot/dts/ox820-pogoplug-pro.dtb
ethact=dwmac.40400000
ethaddr=xxxxxxxxxxxx
fileaddr=64000000
filesize=61202a
if_netconsole=ping $serverip
ipaddr=xxxxxxxx
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
preboot_nc=run if_netconsole start_netconsole
serverip=xxxxxxxxxxx
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version
stderr=serial
stdin=serial
stdout=serial
uenv_import=echo importing envs ...; env import -t 0x60500000
uenv_init_devices=setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices;  do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x60500000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
uimage_addr=0x60500000
uinitrd_addr=0x60e00000
usb_custom_params=zswap.enabled=1
usb_device=0:1
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10

learning is living! Echowarrior108



device pogoplug-pro v3

Debian GNU/Linux bullseye/sid \n \l
Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6) ) #1 SMP PREEMPT Fri Nov 15 04:12:45 PST 2019



Edited 3 time(s). Last edit at 10/25/2020 11:55AM by echowarrior108.
Re: openwrt on pogoplug pro v3
October 26, 2020 11:24PM
echowarrior108,

With the USB rootfs removed, Power up, Interrupt serial console, and,
setenv bootcmd_openwrt 'nboot 60500000 0 440000; bootm'
setenv bootcmd_exec 'if run load_uimage; then; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi; else run bootcmd_openwrt;  fi'
And then boot
boot

And test it a few times with and without the USB rootfs. After that you can do saveenv before boot to make it permanent.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: openwrt on pogoplug pro v3
October 26, 2020 11:26PM
Quote

"2: also is it possible to move the nand openwrt to a bootable usb so I have more room for the OS?"

There is a method in OpenWrt installation that you can set up the extension of the rootfs on USB. You can find it at their website.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: openwrt on pogoplug pro v3
October 27, 2020 03:11PM
bodhi Wrote:
-------------------------------------------------------
> echowarrior108,
>
> With the USB rootfs removed, Power up, Interrupt
> serial console, and,
>
> setenv bootcmd_openwrt 'nboot 60500000 0 440000;
> bootm'
> setenv bootcmd_exec 'if run load_uimage; then; if
> run load_initrd; then if run load_dtb; then bootm
> $load_uimage_addr $load_initrd_addr
> $load_dtb_addr; else bootm $load_uimage_addr
> $load_initrd_addr; fi; else if run load_dtb; then
> bootm $load_uimage_addr - $load_dtb_addr; else
> bootm $load_uimage_addr; fi; fi; else run
> bootcmd_openwrt;  fi'
>
> And then boot
>
> boot
>
>
> And test it a few times with and without the USB
> rootfs. After that you can do saveenv before boot
> to make it permanent.

OX820> setenv bootcmd_openwrt 'nboot 60500000 0 440000; bootm'
OX820> setenv bootcmd_exec 'if run load_uimage; then; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi; else run bootcmd_openwrt;  fi'
OX820> boot

Loading from nand0, offset 0x440000
   Image Name:   ARM OpenWrt Linux-4.14.195
   Created:      2020-09-06  16:19:39 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2765936 Bytes = 2.6 MiB
   Load Address: 60008000
   Entry Point:  60008000
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   ARM OpenWrt Linux-4.14.195
   Created:      2020-09-06  16:19:39 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2765936 Bytes = 2.6 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.195 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11208-ce6496d796)) #0 SMP Sun Sep 6 16:19:39 2020
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Cloud Engines PogoPlug Pro
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 64 MiB at 0x64000000
[    0.000000] random: get_random_bytes called from 0xc07008b8 with crng_init=0
[    0.000000] percpu: Embedded 15 pages/cpu s29100 r8192 d24148 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: earlyprintk console=ttyS0,115200
[    0.000000] Bootloader command line (ignored): console=ttyS0,115200n8
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 56564K/131072K available (5120K kernel code, 128K rwdata, 620K rodata, 1024K init, 208K bss, 8972K reserved, 65536K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0600000   (6112 kB)
[    0.000000]       .init : 0xc0700000 - 0xc0800000   (1024 kB)
[    0.000000]       .data : 0xc0800000 - 0xc0820320   ( 129 kB)
[    0.000000]        .bss : 0xc0823a1c - 0xc0857da8   ( 209 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU event tracing is enabled.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] FPGA IRQ chip 0 "interrupt-controller" @ c8804000, 32 irqs, parent IRQ: 16
[    0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.000046] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000058] timer_oxnas_rps: Registered clocksource rate 390625Hz
[    0.000081] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[    0.000225] GIC: PPI13 is secure or misconfigured
[    0.000273] GIC: PPI13 is secure or misconfigured
[    0.000373] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.050362] pid_max: default: 32768 minimum: 301
[    0.050524] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.050547] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.051253] CPU: Testing write buffer coherency: ok
[    0.052413] Setting up static identity map for 0x60100000 - 0x6010005c
[    0.052628] Hierarchical SRCU implementation.
[    0.053427] smp: Bringing up secondary CPUs ...
[    0.054241] GIC: PPI13 is secure or misconfigured
[    0.110574] smp: Brought up 1 node, 2 CPUs
[    0.110602] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[    0.115415] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.115448] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.120232] pinctrl core: initialized pinctrl subsystem
[    0.120954] NET: Registered protocol family 16
[    0.124610] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.126717] cpuidle: using governor menu
[    0.126801] No ATAGs?
[    0.137912] pps_core: LinuxPPS API ver. 1 registered
[    0.137932] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.137978] PTP clock support registered
[    0.138864] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[    0.140103] NET: Registered protocol family 2
[    0.141007] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.141045] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.141079] TCP: Hash tables configured (established 1024 bind 1024)
[    0.141214] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.141260] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.141493] NET: Registered protocol family 1
[    0.142863] No memory allocated for crashlog
[    0.143111] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.149534] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.152913] io scheduler noop registered
[    0.152934] io scheduler deadline registered
[    0.153180] io scheduler cfq registered (default)
[    0.155233] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.158789] console [ttyS0] disabled
[    0.158996] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[    0.622435] console [ttyS0] enabled
[    0.638960] brd: module loaded
[    0.649699] loop: module loaded
[    0.719152] nand: Could not find valid ONFI parameter page; aborting
[    0.725486] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[    0.731852] nand: Hynix NAND 128MiB 3,3V 8-bit
[    0.736281] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.743851] Scanning device for bad blocks
[    0.830615] 5 fixed-partitions partitions found on MTD device 41000000.nand-controller
[    0.838492] Creating 5 MTD partitions on "41000000.nand-controller":
[    0.844853] 0x000000000000-0x000000040000 : "stage1"
[    0.850872] 0x000000040000-0x0000003c0000 : "u-boot"
[    0.856768] 0x0000003c0000-0x000000440000 : "u-boot-env"
[    0.863088] 0x000000440000-0x000000e00000 : "kernel"
[    0.869168] 0x000000e00000-0x000008000000 : "ubi"
[    0.875883] libphy: Fixed MDIO Bus: probed
[    0.880645] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[    0.886461] oxnas-dwmac 40400000.ethernet: no reset control found
[    0.958940] stmmac - user ID: 0x12, Synopsys ID: 0x35
[    0.963980] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[    0.969664] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[    0.976939] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[    0.983720] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[    0.990333] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[    0.997603] oxnas-dwmac 40400000.ethernet: COE Type 2
[    1.002657] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[    1.009525] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[    1.015841] oxnas-dwmac 40400000.ethernet (unnamed net_device) (uninitialized): device MAC address fa:15:67:81:91:1f
[    1.026352] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.043356] libphy: stmmac: probed
[    1.046758] RTL8211DN Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    1.059443] RTL8211DN Gigabit Ethernet stmmac-0:03: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:03, irq=POLL)
[    1.074032] ledtrig-cpu: registered to indicate activity on CPUs
[    1.080192] hidraw: raw HID events driver (C) Jiri Kosina
[    1.086860] NET: Registered protocol family 10
[    1.092869] Segment Routing with IPv6
[    1.096606] NET: Registered protocol family 17
[    1.101209] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.114176] 8021q: 802.1Q VLAN Support v1.8
[    1.368898] oxnas-pcie 47c00000.pcie-controller: PCIe version/deviceID 0x82510b5
[    1.376271] oxnas-pcie 47c00000.pcie-controller: link up
[    1.381890] oxnas-pcie 47c00000.pcie-controller: PCI host bridge to bus 0000:00
[    1.389224] pci_bus 0000:00: root bus resource [mem 0x48000000-0x49ffffff]
[    1.396067] pci_bus 0000:00: root bus resource [mem 0x4a000000-0x4bdfffff pref]
[    1.403376] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff]
[    1.409648] pci_bus 0000:00: root bus resource [bus 00-7f]
[    1.415610] PCI: bus0: Fast back to back transfers disabled
[    1.421230] pci 0000:00:00.0: BAR 0: assigned [mem 0x48000000-0x4800ffff]
[    1.428454] UBI: auto-attach mtd4
[    1.431838] ubi0: attaching mtd4
[    1.557806] ubi0: scanning is finished
[    1.570529] ubi0: attached mtd4 (name "ubi", size 114 MiB)
[    1.575994] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    1.582894] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    1.589593] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[    1.596346] ubi0: good PEBs: 912, bad PEBs: 0, corrupted PEBs: 0
[    1.602352] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    1.609569] ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 1761439147
[    1.618657] ubi0: available PEBs: 0, total reserved PEBs: 912, PEBs reserved for bad PEB handling: 20
[    1.627916] ubi0: background thread "ubi_bgt0d" started, PID 44
[    1.629145] block ubiblock0_0: created from ubi0:0(rootfs)
[    1.639326] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    1.646261] hctosys: unable to open rtc device (rtc0)
[    1.657059] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    1.665984] Freeing unused kernel memory: 1024K
[    1.996367] init: Console is alive
[    2.542476] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.616153] usbcore: registered new interface driver usbfs
[    2.621775] usbcore: registered new interface driver hub
[    2.627176] usbcore: registered new device driver usb
[    2.633182] Button Hotplug driver version 0.4.1
[    2.639546] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.647011] ehci-platform: EHCI generic platform driver
[    2.858905] oxnas-ehci 40200100.ehci: EHCI Host Controller
[    2.864432] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[    2.872604] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100
[    2.898903] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[    2.905930] hub 1-0:1.0: USB hub found
[    2.909818] hub 1-0:1.0: 2 ports detected
[    2.916700] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    2.930334] init: - preinit -
[    3.288998] usb 1-1: new high-speed USB device number 2 using oxnas-ehci
[    3.504097] random: jshn: uninitialized urandom read (4 bytes read)
[    3.542039] random: procd: uninitialized urandom read (4 bytes read)
[    3.542190] hub 1-1:1.0: USB hub found
[    3.552657] hub 1-1:1.0: 4 ports detected
[    3.568501] random: jshn: uninitialized urandom read (4 bytes read)
[    3.628421] RTL8211DN Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    3.648957] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[    3.657518] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock
[    3.665671] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    3.888890] usb 1-1.3: new high-speed USB device number 3 using oxnas-ehci
[    6.898234] mount_root: loading kmods from internal overlay
[    6.920581] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    6.928499] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[    7.152281] __nand_correct_data: uncorrectable ECC error
[    7.157578] __nand_correct_data: uncorrectable ECC error
[    7.162944] print_req_error: I/O error, dev mtdblock1, sector 2048
[    7.169456] __nand_correct_data: uncorrectable ECC error
[    7.174748] __nand_correct_data: uncorrectable ECC error
[    7.180088] print_req_error: I/O error, dev mtdblock1, sector 2048
[    7.186242] Buffer I/O error on dev mtdblock1, logical block 256, async page read
[    7.293035] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 111
[    7.327042] UBIFS (ubi0:1): recovery needed
[    7.506700] UBIFS (ubi0:1): recovery completed
[    7.511915] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[    7.519754] UBIFS (ubi0:1): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    7.529653] UBIFS (ubi0:1): FS size: 110057472 bytes (104 MiB, 853 LEBs), journal size 5548032 bytes (5 MiB, 43 LEBs)
[    7.540239] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[    7.546828] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 25EAB2F5-5759-49E0-9B6A-9300CB685771, small LPT model
[    7.558881] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[    7.568565] block: extroot: device not present, retrying in 5 seconds
[   12.635781] __nand_correct_data: uncorrectable ECC error
[   12.641134] __nand_correct_data: uncorrectable ECC error
[   12.646435] print_req_error: I/O error, dev mtdblock1, sector 2048
[   12.652915] __nand_correct_data: uncorrectable ECC error
[   12.658204] __nand_correct_data: uncorrectable ECC error
[   12.663534] print_req_error: I/O error, dev mtdblock1, sector 2048
[   12.669690] Buffer I/O error on dev mtdblock1, logical block 256, async page read
[   12.769175] block: extroot: cannot find device with UUID 763e1760-6b36-42ae-aaf5-b64aaa25e05b
[   12.809113] UBIFS (ubi0:1): un-mount UBI device 0
[   12.813862] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[   12.825533] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 112
[   12.884533] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   12.892410] UBIFS (ubi0:1): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   12.902336] UBIFS (ubi0:1): FS size: 110057472 bytes (104 MiB, 853 LEBs), journal size 5548032 bytes (5 MiB, 43 LEBs)
[   12.912924] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[   12.919539] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 25EAB2F5-5759-49E0-9B6A-9300CB685771, small LPT model
[   12.932436] mount_root: loading kmods from internal overlay
[   12.979453] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   13.111114] SCSI subsystem initialized
[   13.125949] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   13.133273] ohci-platform: OHCI generic platform driver
[   13.142753] uhci_hcd: USB Universal Host Controller Interface driver
[   13.157509] usb-storage 1-1.3:1.0: USB Mass Storage device detected
[   13.164597] scsi host0: usb-storage 1-1.3:1.0
[   13.169728] usbcore: registered new interface driver usb-storage
[   13.175984] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   13.255398] __nand_correct_data: uncorrectable ECC error
[   13.260764] __nand_correct_data: uncorrectable ECC error
[   13.266063] print_req_error: I/O error, dev mtdblock1, sector 2048
[   13.272555] __nand_correct_data: uncorrectable ECC error
[   13.277847] __nand_correct_data: uncorrectable ECC error
[   13.283187] print_req_error: I/O error, dev mtdblock1, sector 2048
[   13.289338] Buffer I/O error on dev mtdblock1, logical block 256, async page read
[   13.393904] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   13.402833] block: extroot: device not present, retrying in 5 seconds
[   14.250408] scsi 0:0:0:0: Direct-Access     SanDisk  Cruzer Glide     1.00 PQ: 0 ANSI: 6
[   14.261079] sd 0:0:0:0: [sda] 123174912 512-byte logical blocks: (63.1 GB/58.7 GiB)
[   14.270679] sd 0:0:0:0: [sda] Write Protect is off
[   14.276303] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   14.382384]  sda: sda1 sda2
[   14.390184] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   18.470320] __nand_correct_data: uncorrectable ECC error
[   18.475617] __nand_correct_data: uncorrectable ECC error
[   18.480977] print_req_error: I/O error, dev mtdblock1, sector 2048
[   18.487390] __nand_correct_data: uncorrectable ECC error
[   18.492736] __nand_correct_data: uncorrectable ECC error
[   18.498032] print_req_error: I/O error, dev mtdblock1, sector 2048
[   18.504184] Buffer I/O error on dev mtdblock1, logical block 256, async page read
[   18.654213] random: fast init done
[   18.784637] block: extroot: cannot find device with UUID 763e1760-6b36-42ae-aaf5-b64aaa25e05b
[   18.840384] mount_root: switching to ubifs overlay
[   18.864965] urandom-seed: Seeding with /etc/urandom.seed
[   18.963330] procd: - early -
[   19.647219] procd: - ubus -
[   19.702691] urandom_read: 1 callbacks suppressed
[   19.702702] random: ubusd: uninitialized urandom read (4 bytes read)
[   19.715008] random: ubusd: uninitialized urandom read (4 bytes read)
[   19.721948] random: ubusd: uninitialized urandom read (4 bytes read)
[   19.730170] procd: - init -
Please press Enter to activate this console.
[   20.316968] Adding 5119996k swap on /dev/sda2.  Priority:-2 extents:1 across:5119996k 
[   20.351843] urngd: v1.0.2 started.
[   20.380518] kmodloader: loading kernel modules from /etc/modules.d/*
[   20.406184] tun: Universal TUN/TAP device driver, 1.6
[   20.423797] Loading modules backported from Linux version v4.19.137-0-gc076c79e03c6
[   20.431516] Backport generated by backports.git v4.19.137-1-0-g60c3a249
[   20.444779] random: crng init done
[   20.448261] random: 3 urandom warning(s) missed due to ratelimiting
[   20.460106] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   20.526776] xt_time: kernel timezone is -0000
[   20.549821] ip_tables: (C) 2000-2006 Netfilter Core Team
[   20.611287] rt2800pci 0000:00:00.0: enabling device (0140 -> 0142)
[   20.617643] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3090, rev 3213 detected
[   20.628920] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
[   20.641169] kmodloader: done loading kernel modules from /etc/modules.d/*
[   24.441159] __nand_correct_data: uncorrectable ECC error
[   24.446458] __nand_correct_data: uncorrectable ECC error
[   24.451883] print_req_error: I/O error, dev mtdblock1, sector 2048
[   24.463362] __nand_correct_data: uncorrectable ECC error
[   24.468666] __nand_correct_data: uncorrectable ECC error
[   24.474137] print_req_error: I/O error, dev mtdblock1, sector 2048
[   24.480302] Buffer I/O error on dev mtdblock1, logical block 256, async page read
[   25.809152] RTL8211DN Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[   25.849064] oxnas-dwmac 40400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   25.857712] oxnas-dwmac 40400000.ethernet eth0: registered PTP clock
[   25.866449] br-lan: port 1(eth0) entered blocking state
[   25.871802] br-lan: port 1(eth0) entered disabled state
[   25.877445] device eth0 entered promiscuous mode
[   25.888396] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   28.460070] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[   28.469742] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.40
[   34.707141] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[   34.717772] br-lan: port 2(wlan0-1) entered blocking state
[   34.723358] br-lan: port 2(wlan0-1) entered disabled state
[   34.729231] device wlan0-1 entered promiscuous mode
[   35.020741] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   36.331422] wlan0: authenticate with 60:38:e0:c5:00:01
[   36.341235] wlan0: send auth to 60:38:e0:c5:00:01 (try 1/3)
[   36.348288] wlan0: authenticated
[   36.358983] wlan0: associate with 60:38:e0:c5:00:01 (try 1/3)
[   36.375672] wlan0: RX AssocResp from 60:38:e0:c5:00:01 (capab=0x511 status=0 aid=4)
[   36.383587] wlan0: associated
[   36.402301] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   36.479500] wlan0: Limiting TX power to 30 (30 - 0) dBm as advertised by 60:38:e0:c5:00:01
[   36.582663] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[   36.589493] br-lan: port 2(wlan0-1) entered blocking state
[   36.595008] br-lan: port 2(wlan0-1) entered forwarding state
[   36.601233] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready


the above is with usb rootfs insert as the example, which is what it does without the usb rootfs inserted,it goes to openwrt regardless, won't pick up usb rootfs.

learning is living! Echowarrior108



device pogoplug-pro v3

Debian GNU/Linux bullseye/sid \n \l
Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6) ) #1 SMP PREEMPT Fri Nov 15 04:12:45 PST 2019



Edited 1 time(s). Last edit at 10/27/2020 06:30PM by echowarrior108.
Re: openwrt on pogoplug pro v3
October 27, 2020 03:17PM
bodhi Wrote:
-------------------------------------------------------
>
Quote

"2: also is it possible to move the nand
> openwrt to a bootable usb so I have more room for
> the OS?"
>
> There is a method in OpenWrt installation that you
> can set up the extension of the rootfs on USB. You
> can find it at their website.


I set up openwrt as /overlay so working with it in nand is working well without loss of space, this may however interfere with the rootfs usb setup. It may be just as easy to interrupt when needed,lol!! thanks for assist!!

learning is living! Echowarrior108



device pogoplug-pro v3

Debian GNU/Linux bullseye/sid \n \l
Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6) ) #1 SMP PREEMPT Fri Nov 15 04:12:45 PST 2019
Re: openwrt on pogoplug pro v3
October 27, 2020 04:28PM
Echowarrior108,

Quote

goes to openwrt regardless, won't pick up usb rootfs.

I am not sure I understood. Please post log.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: openwrt on pogoplug pro v3
October 27, 2020 06:05PM
With the usb rootfs unplugged it loads to openwrt on nand ], when I restart and use the same steps as you posted and use the rootfs usb and boot it loads to nand openwrt anyway. :) I posted the log when usb rootfs was inserted as an example.I edited that for more clarity:)

learning is living! Echowarrior108



device pogoplug-pro v3

Debian GNU/Linux bullseye/sid \n \l
Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6) ) #1 SMP PREEMPT Fri Nov 15 04:12:45 PST 2019



Edited 1 time(s). Last edit at 10/27/2020 06:31PM by echowarrior108.
Re: openwrt on pogoplug pro v3
October 27, 2020 06:48PM
Ok. As I can see above, your envs look quite messed up!

Or the envs were from a much older version, not the latest in
https://forum.doozan.com/read.php?3,16017

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: openwrt on pogoplug pro v3
October 27, 2020 10:10PM
lol, yep the envs are a mess, its my backup plug and I just tried openwrt on it as it was laying around and hadn't got into the envs as much as learning the openwrt which for some mysterious reason works great even with the messed up uboot.. I should have clean slated it first but hadn;t thought about it. I will do that tonight and see if that helps with your settings included:) Thanks!!


followup, installed new uboot this is the initial printenv:

OX820> printenv
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm 0x60500000 0x60e00000 0x62c00000; else bootm 0x60500000 0x60e00000; fi; else if run load_dtb; then bootm 0x60500000 - 0x62c00000; else bootm 0x60500000; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
device=0:1
devices=usb ide
disks=0 1 2 3
dtb_file=/boot/dts/ox820-pogoplug-pro.dtb
ethact=dwmac.40400000
ethaddr=52:3b:20:9c:11:51
if_netconsole=ping $serverip
ipaddr=192.168.0.222
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device 0x62c00000 $dtb_file
load_initrd=echo loading uInitrd ...; load $bootdev $device 0x60e00000 /boot/uInitrd
load_uimage=echo loading uImage ...; load $bootdev $device 0x60500000 /boot/uImage
mainlineLinux=yes
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start";  setenv scan_ide "ide reset";  setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 0x60500000 /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_import=echo importing envs ...; env import -t 0x60510000  $filesize
uenv_init_devices=setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices;  do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x60500000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
usb_custom_params=zswap.enabled=1
usb_ready_retry=15


it did start right up into debian so all is good there, I will try the changes and post later:)

learning is living! Echowarrior108



device pogoplug-pro v3

Debian GNU/Linux bullseye/sid \n \l
Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6) ) #1 SMP PREEMPT Fri Nov 15 04:12:45 PST 2019



Edited 2 time(s). Last edit at 10/27/2020 10:45PM by echowarrior108.
Re: openwrt on pogoplug pro v3
October 27, 2020 10:57PM
success!!!!
bodhi is genious!


later on I may go further and have duel os on one sata, mountain to climb later:)
then the challenge of making the os choice before boot... long way off on that one but I do have a spare hdd, see I upgrade my 2 ps3 units with ssd's, so I now one drive left to salvage for fun projects like these. What prompted this one was I crashed my router and was offline and too cheap to go out and buy another router when I could make a pogoplug into one... now I have a spare router in case of emergency!!:)

makes it all worthwhile when project have a use:)

learning is living! Echowarrior108



device pogoplug-pro v3

Debian GNU/Linux bullseye/sid \n \l
Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6) ) #1 SMP PREEMPT Fri Nov 15 04:12:45 PST 2019
Re: openwrt on pogoplug pro v3
October 28, 2020 05:34AM
Cool!

> later on I may go further and have duel os on one
> sata, mountain to climb later:)
> then the challenge of making the os choice before
> boot..


It's a little bit user unfriendly, but possible. With headless system like this, you need to do either one of the following to select a choice:

- Use serical console to enter a command to boot to the selected OS.
- Use netconsole to enter a command to boot to the selected OS.
- Use uEnv.txt to set an env to tell u-boot to boot to the selected OS.
- While the Debian is running, set an env to to tell u-boot to boot to the other OS upon reboot.
- Use a USB drive as a signal to tell u-boot to boot into one of the OS on HDD.

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 1 time(s). Last edit at 10/28/2020 05:35AM by bodhi.
Re: openwrt on pogoplug pro v3
October 28, 2020 11:16AM
When I get some time I will work it out. got so issues of a personal nature going on so it will be hit and miss...:)

learning is living! Echowarrior108



device pogoplug-pro v3

Debian GNU/Linux bullseye/sid \n \l
Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6) ) #1 SMP PREEMPT Fri Nov 15 04:12:45 PST 2019
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: