Can't boot from SATA after power fail goes into Rescue

I have a system that typically boots into an ext3 Hard Drive (should allow it to survive power failures), but now will only boot into the rescue system. When I try to do anything on /dev/sda it says there is no drive, there are no USB devices attached.

I have tried /dev/sdb as well, but I didn't expect anything there either.

Anyone know how to figure out if my drive is no working or there is a problem with the Goflex Home?

Did uBoot detect it at all? ie. stop netconsole/serial console and check for SATA (I assume you are using a drive that is plugged into SATA port).

ide reset

Whether it did recognize the HDD or not. Put my latest rootfs (in signature) on a USB thumb and boot with it. In Debian, plug in the HDD to see if it is detected in dmesg. Then do e2fsck to fix any error.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 01/10/2014 11:12PM by bodhi.

I had forgotten I had a new computer without serial cable drivers since I could not get netconsole to work (I forgot to set the local ip! HA!)

Well, I booted into an old rootfs of yours I had on a stick 3.10.something. I have seen several different things along the way about the sata port so figure I will just post my environment, my 'mount', and dmesg and see what the experts say.

BTW printenv didnt seem to work in your rootfs so I went back to the rescue to get it

# fw_printenv
baudrate=115200
bootcmd_usb=run usb_init; run usb_load_uimage; run set_bootargs_usb; run usb_boot;
bootdelay=3
console=ttyS0,115200
ethact=egiga0
ethaddr=xxxxxxxxxx
led_error=orange blinking
led_exit=green off
led_init=green blinking
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts
stderr=serial
stdin=serial
stdout=serial
usb_boot=if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000;else bootm 0x800000;fi;
usb_device=0:1
usb_load_uimage=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage
usb_root=/dev/sda1
usb_rootdelay=10
usb_rootfstype=ext2
set_bootargs_rescue=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts
bootcmd_rescue=run set_bootargs_rescue; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000
bootcmd_pogo=run bootcmd_rescue
rescue_installed=1
usb_init=usb start; setenv usb_root LABEL=rootfs
sata_init=ide reset
sata_root=/dev/sda1
bootcmd_sata=run sata_init; run sata_load_uimage; run set_bootargs_sata; run sata_boot;
set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$sata_rootdelay rootfstype=$sata_rootfstype $mtdparts
sata_rootdelay=8
sata_device=0:1
sata_boot=if ext2load ide $sata_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000;else bootm 0x800000;fi;
bootcmd=run bootcmd_usb; usb stop; run bootcmd_sata; run bootcmd_pogo; reset
sata_load_uimage=mw 0x800000 0 1; ext2load ide $sata_device 0x800000 /boot/uImage
arcNumber=3338
sata_rootfstype=ext3
if_netconsole=ping $serverip
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
preboot=run if_netconsole start_netconsole
serverip=192.168.1.119
ipaddr=192.168.1.210

# mount
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,relatime)
udev on /dev type devtmpfs (rw,relatime,size=10240k,nr_inodes=14643,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000)
tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=12368k,mode=755)
/dev/disk/by-label/rootfs on / type ext2 (rw,noatime,errors=remount-ro)
tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k)
tmpfs on /run/shm type tmpfs (rw,nosuid,nodev,noexec,relatime,size=24720k)
tmpfs on /tmp type tmpfs (rw,relatime)
rpc_pipefs on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw,relatime)

# dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.4-kirkwood-tld-1 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 PREEMPT Tue Aug 20 23:25:42 PDT 2013
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Seagate GoFlex Home
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat c05dbf50, node_mem_map c0648000
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 117144k/117144k available, 13928k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0561b44   (5479 kB)
[    0.000000]       .init : 0xc0562000 - 0xc05909bc   ( 187 kB)
[    0.000000]       .data : 0xc0592000 - 0xc05de6d0   ( 306 kB)
[    0.000000]        .bss : 0xc05de6d0 - 0xc06470f4   ( 419 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:114
[    0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[    0.000000] Console: colour dummy device 80x30
[   20.478340] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[   20.568161] pid_max: default: 32768 minimum: 301
[   20.568264] Security Framework initialized
[   20.568331] Mount-cache hash table entries: 512
[   20.568937] Initializing cgroup subsys devices
[   20.568960] Initializing cgroup subsys freezer
[   20.568973] Initializing cgroup subsys net_cls
[   20.568984] Initializing cgroup subsys blkio
[   20.569072] CPU: Testing write buffer coherency: ok
[   20.569464] Setting up static identity map for 0xc03e88c8 - 0xc03e8904
[   20.571288] devtmpfs: initialized
[   20.573680] pinctrl core: initialized pinctrl subsystem
[   20.574010] regulator-dummy: no parameters
[   20.574321] NET: Registered protocol family 16
[   20.574743] DMA: preallocated 256 KiB pool for atomic coherent allocations
[   20.575445] Kirkwood: MV88F6281-A1, TCLK=200000000.
[   20.575475] Feroceon L2: Enabling L2
[   20.575513] Feroceon L2: Cache support initialised.
[   20.575843] initial MPP regs: 01111111 11113322 00001111 00100000 00000000 00000000 00000000
[   20.575870]   final MPP regs: 01111111 11113322 00001111 00000000 00000000 00000000 00000000
[   20.579315] bio: create slab <bio-0> at 0
[   20.579734] vgaarb: loaded
[   20.579858] usbcore: registered new interface driver usbfs
[   20.579918] usbcore: registered new interface driver hub
[   20.580017] usbcore: registered new device driver usb
[   20.580616] Switching to clocksource orion_clocksource
[   20.594607] NET: Registered protocol family 2
[   20.595240] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[   20.595275] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[   20.595296] TCP: Hash tables configured (established 1024 bind 1024)
[   20.595363] TCP: reno registered
[   20.595378] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   20.595399] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   20.595595] NET: Registered protocol family 1
[   20.595903] RPC: Registered named UNIX socket transport module.
[   20.595915] RPC: Registered udp transport module.
[   20.595922] RPC: Registered tcp transport module.
[   20.595929] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   20.595941] PCI: CLS 0 bytes, default 32
[   20.596133] Unpacking initramfs...
[   21.137286] Freeing initrd memory: 6324K (c1101000 - c172e000)
[   21.137391] NetWinder Floating Point Emulator V0.97 (double precision)
[   21.137896] audit: initializing netlink socket (disabled)
[   21.137947] type=2000 audit(0.650:1): initialized
[   21.138754] VFS: Disk quotas dquot_6.5.2
[   21.138805] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   21.139163] NFS: Registering the id_resolver key type
[   21.139223] Key type id_resolver registered
[   21.139233] Key type id_legacy registered
[   21.139251] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   21.139404] jffs2: version 2.2. (NAND) (SUMMARY)  \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc.
[   21.139615] msgmni has been set to 241
[   21.141490] alg: No test for stdrng (krng)
[   21.141586] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[   21.141597] io scheduler noop registered
[   21.141605] io scheduler deadline registered
[   21.141631] io scheduler cfq registered (default)
[   21.141751] mv_xor mv_xor.0: Marvell shared XOR driver
[   21.180695] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[   21.220694] mv_xor mv_xor.0: Marvell XOR: ( xor fill cpy )
[   21.220796] mv_xor mv_xor.1: Marvell shared XOR driver
[   21.260694] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[   21.300692] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[   21.300937] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   21.321483] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[   21.818453] console [ttyS0] enabled
[   21.822959] ONFI param page 0 valid
[   21.826463] ONFI flash detected
[   21.829625] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD), 256MiB, page size: 2048, OOB size: 64
[   21.840744] Scanning device for bad blocks
[   22.060178] 4 cmdlinepart partitions found on MTD device orion_nand
[   22.066488] Creating 4 MTD partitions on "orion_nand":
[   22.071676] 0x000000000000-0x000000100000 : "u-boot"
[   22.076880] 0x000000100000-0x000000500000 : "uImage"
[   22.082092] 0x000000500000-0x000002500000 : "rootfs"
[   22.087312] 0x000002500000-0x000010000000 : "data"
[   22.092622] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   22.099181] ehci-pci: EHCI PCI platform driver
[   22.103709] ehci-orion: EHCI orion driver
[   22.107788] orion-ehci orion-ehci.0: EHCI Host Controller
[   22.113251] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   22.120983] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   22.140672] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   22.146696] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   22.153541] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   22.160815] usb usb1: Product: EHCI Host Controller
[   22.165717] usb usb1: Manufacturer: Linux 3.10.4-kirkwood-tld-1 ehci_hcd
[   22.172463] usb usb1: SerialNumber: orion-ehci.0
[   22.177508] hub 1-0:1.0: USB hub found
[   22.181314] hub 1-0:1.0: 1 port detected
[   22.185660] mousedev: PS/2 mouse device common for all mice
[   22.191617] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[   22.197544] i2c /dev entries driver
[   22.201164] cpuidle: using governor ladder
[   22.205277] cpuidle: using governor menu
[   22.209385] leds-gpio leds-gpio: pins are not configured from the driver
[   22.216429] drop_monitor: Initializing network drop monitor service
[   22.223027] TCP: cubic registered
[   22.226365] NET: Registered protocol family 17
[   22.230937] Key type dns_resolver registered
[   22.235620] registered taskstats version 1
[   22.240575] rtc-mv rtc-mv: setting system clock to 2014-01-11 16:05:32 UTC (1389456332)
[   22.249443] Freeing unused kernel memory: 184K (c0562000 - c0590000)
[   22.321349] udevd[52]: starting version 175
[   22.389106] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   22.473866] libphy: PHY orion-mdio-mii:00 not found
[   22.478797] platform mv643xx_eth_port.0: Driver mv643xx_eth_port requests probe deferral
[   22.500728] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   22.515430] SCSI subsystem initialized
[   22.576250] libphy: orion_mdio_bus: probed
[   22.581683] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 02:50:43:36:64:77
[   22.597457] libata version 3.00 loaded.
[   22.610770] sata_mv sata_mv.0: version 1.28
[   22.610831] sata_mv sata_mv.0: cannot get optional clkdev
[   22.616311] sata_mv sata_mv.0: slots 32 ports 1
[   22.653255] scsi0 : sata_mv
[   22.656289] ata1: SATA max UDMA/133 irq 21
[   22.661748] usb 1-1: New USB device found, idVendor=0781, idProduct=556b
[   22.668505] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   22.688044] usb 1-1: Product: Cruzer Edge
[   22.696076] usb 1-1: Manufacturer: SanDisk
[   22.700203] usb 1-1: SerialNumber: 20060774210EFE307EA0
[   22.738079] usb-storage 1-1:1.0: USB Mass Storage device detected
[   22.744505] scsi1 : usb-storage 1-1:1.0
[   22.749888] usbcore: registered new interface driver usb-storage
[   23.000679] ata1: SATA link down (SStatus 0 SControl F300)
[   23.691896] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen
[   23.699329] ata1: edma_err_cause=00000010 pp_flags=00000000, dev connect
[   23.706087] ata1: SError: { PHYRdyChg DevExch }
[   23.710674] ata1: hard resetting link
[   23.741593] scsi 1:0:0:0: Direct-Access     SanDisk  Cruzer Edge      1.18 PQ: 0 ANSI: 5
[   23.765179] sd 1:0:0:0: [sda] 7821312 512-byte logical blocks: (4.00 GB/3.72 GiB)
[   23.774652] sd 1:0:0:0: [sda] Write Protect is off
[   23.779470] sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
[   23.780141] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   23.798637]  sda: sda1 sda2
[   23.805513] sd 1:0:0:0: [sda] Attached SCSI removable disk
[   23.821407] sd 1:0:0:0: Attached scsi generic sg0 type 0
[   24.460681] ata1: SATA link down (SStatus 0 SControl F300)
[   24.466223] ata1: EH complete
[   33.099167] EXT2-fs (sda1): warning: mounting ext3 filesystem as ext2
[   34.318942] udevd[232]: starting version 175
[   34.769374] alg: hash: Test 1 failed for mv-hmac-sha1
[   34.777997] 00000000: 0c aa 9f d5 37 c3 79 3a 91 d9 21 5f 42 2b 2c 24
[   34.790889] 00000010: b7 c3 16 0c
[   34.809608] orion_wdt: Initial timeout 21 sec
[   40.022145] NET: Registered protocol family 10
[   40.184025] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
[   40.190106] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   43.895223] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   43.905144] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

It looks very good.

Now when you plug in the HDD,what dmesg says?

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

The HD was plugged in! I have not removed it. I will shutdown, do a reboot without it and a reboot with it in.

Can I hotplug the SATA HD? I can try that and look at dmesg if it would help but don't wnat to do it if thats a no-no.


NO HD:

# dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.4-kirkwood-tld-1 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 PREEMPT Tue Aug 20 23:25:42 PDT 2013
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Seagate GoFlex Home
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat c05dbf50, node_mem_map c0648000
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 117144k/117144k available, 13928k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0561b44   (5479 kB)
[    0.000000]       .init : 0xc0562000 - 0xc05909bc   ( 187 kB)
[    0.000000]       .data : 0xc0592000 - 0xc05de6d0   ( 306 kB)
[    0.000000]        .bss : 0xc05de6d0 - 0xc06470f4   ( 419 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:114
[    0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[    0.000000] Console: colour dummy device 80x30
[   20.478270] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[   20.568091] pid_max: default: 32768 minimum: 301
[   20.568193] Security Framework initialized
[   20.568261] Mount-cache hash table entries: 512
[   20.568867] Initializing cgroup subsys devices
[   20.568889] Initializing cgroup subsys freezer
[   20.568903] Initializing cgroup subsys net_cls
[   20.568913] Initializing cgroup subsys blkio
[   20.569002] CPU: Testing write buffer coherency: ok
[   20.569393] Setting up static identity map for 0xc03e88c8 - 0xc03e8904
[   20.571217] devtmpfs: initialized
[   20.573609] pinctrl core: initialized pinctrl subsystem
[   20.573939] regulator-dummy: no parameters
[   20.574250] NET: Registered protocol family 16
[   20.574673] DMA: preallocated 256 KiB pool for atomic coherent allocations
[   20.575374] Kirkwood: MV88F6281-A1, TCLK=200000000.
[   20.575405] Feroceon L2: Enabling L2
[   20.575443] Feroceon L2: Cache support initialised.
[   20.575773] initial MPP regs: 01111111 11113322 00001111 00100000 00000000 00000000 00000000
[   20.575800]   final MPP regs: 01111111 11113322 00001111 00000000 00000000 00000000 00000000
[   20.579244] bio: create slab <bio-0> at 0
[   20.579663] vgaarb: loaded
[   20.579787] usbcore: registered new interface driver usbfs
[   20.579848] usbcore: registered new interface driver hub
[   20.579947] usbcore: registered new device driver usb
[   20.580545] Switching to clocksource orion_clocksource
[   20.594537] NET: Registered protocol family 2
[   20.595170] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[   20.595206] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[   20.595226] TCP: Hash tables configured (established 1024 bind 1024)
[   20.595294] TCP: reno registered
[   20.595309] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   20.595330] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   20.595526] NET: Registered protocol family 1
[   20.595834] RPC: Registered named UNIX socket transport module.
[   20.595846] RPC: Registered udp transport module.
[   20.595853] RPC: Registered tcp transport module.
[   20.595860] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   20.595872] PCI: CLS 0 bytes, default 32
[   20.596064] Unpacking initramfs...
[   21.137136] Freeing initrd memory: 6324K (c1101000 - c172e000)
[   21.137240] NetWinder Floating Point Emulator V0.97 (double precision)
[   21.137744] audit: initializing netlink socket (disabled)
[   21.137796] type=2000 audit(0.650:1): initialized
[   21.138600] VFS: Disk quotas dquot_6.5.2
[   21.138651] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   21.139010] NFS: Registering the id_resolver key type
[   21.139086] Key type id_resolver registered
[   21.139096] Key type id_legacy registered
[   21.139114] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   21.139266] jffs2: version 2.2. (NAND) (SUMMARY)  \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc.
[   21.139479] msgmni has been set to 241
[   21.141357] alg: No test for stdrng (krng)
[   21.141454] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[   21.141466] io scheduler noop registered
[   21.141473] io scheduler deadline registered
[   21.141500] io scheduler cfq registered (default)
[   21.141619] mv_xor mv_xor.0: Marvell shared XOR driver
[   21.180623] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[   21.220623] mv_xor mv_xor.0: Marvell XOR: ( xor fill cpy )
[   21.220725] mv_xor mv_xor.1: Marvell shared XOR driver
[   21.260623] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[   21.300622] mv_xor mv_xorr.1: Marvell XOR: ( xor fill cpy )
[   21.300868] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   21.321412] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[   21.818350] console [ttyS0] enabled
[   21.822859] ONFI param page 0 valid
[   21.826361] ONFI flash detected
[   21.829522] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD), 256MiB, page size: 2048, OOB size: 64
[   21.840640] Scanning device for bad blocks
[   22.060076] 4 cmdlinepart partitions found on MTD device orion_nand
[   22.066385] Creating 4 MTD partitions on "orion_nand":
[   22.071575] 0x000000000000-0x000000100000 : "u-boot"
[   22.076787] 0x000000100000-0x000000500000 : "uImage"
[   22.081999] 0x000000500000-0x000002500000 : "rootfs"
[   22.087217] 0x000002500000-0x000010000000 : "data"
[   22.092524] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   22.099077] ehci-pci: EHCI PCI platform driver
[   22.103606] ehci-orion: EHCI orion driver
[   22.107685] orion-ehci orion-ehci.0: EHCI Host Controller
[   22.113148] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   22.120913] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   22.140601] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   22.146628] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   22.153470] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   22.160737] usb usb1: Product: EHCI Host Controller
[   22.165641] usb usb1: Manufacturer: Linux 3.10.4-kirkwood-tld-1 ehci_hcd
[   22.172387] usb usb1: SerialNumber: orion-ehci.0
[   22.177434] hub 1-0:1.0: USB hub found
[   22.181248] hub 1-0:1.0: 1 port detected
[   22.185590] mousedev: PS/2 mouse device common for all mice
[   22.191549] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[   22.197476] i2c /dev entries driver
[   22.201095] cpuidle: using governor ladder
[   22.205209] cpuidle: using governor menu
[   22.209317] leds-gpio leds-gpio: pins are not configured from the driver
[   22.216361] drop_monitor: Initializing network drop monitor service
[   22.222957] TCP: cubic registered
[   22.226288] NET: Registered protocol family 17
[   22.230860] Key type dns_resolver registered
[   22.235551] registered taskstats version 1
[   22.240501] rtc-mv rtc-mv: setting system clock to 2014-01-11 16:43:40 UTC (1389458620)
[   22.249365] Freeing unused kernel memory: 184K (c0562000 - c0590000)
[   22.321277] udevd[52]: starting version 175
[   22.389115] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   22.475095] libphy: PHY orion-mdio-mii:00 not found
[   22.480028] platform mv643xx_eth_port.0: Driver mv643xx_eth_port requests probe deferral
[   22.500660] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   22.514996] SCSI subsystem initialized
[   22.573801] libphy: orion_mdio_bus: probed
[   22.579183] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 02:50:43:36:64:77
[   22.597575] libata version 3.00 loaded.
[   22.610756] sata_mv sata_mv.0: version 1.28
[   22.610818] sata_mv sata_mv.0: cannot get optional clkdev
[   22.616304] sata_mv sata_mv.0: slots 32 ports 1
[   22.652632] scsi0 : sata_mv
[   22.655669] ata1: SATA max UDMA/133 irq 21
[   22.661675] usb 1-1: New USB device found, idVendor=0781, idProduct=556b
[   22.668427] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   22.687964] usb 1-1: Product: Cruzer Edge
[   22.696328] usb 1-1: Manufacturer: SanDisk
[   22.700448] usb 1-1: SerialNumber: 20060774210EFE307EA0
[   22.738029] usb-storage 1-1:1.0: USB Mass Storage device detected
[   22.744454] scsi1 : usb-storage 1-1:1.0
[   22.749829] usbcore: registered new interface driver usb-storage
[   23.000609] ata1: SATA link down (SStatus 0 SControl F300)
[   23.741522] scsi 1:0:0:0: Direct-Access     SanDisk  Cruzer Edge      1.18 PQ: 0 ANSI: 5
[   23.765229] sd 1:0:0:0: [sda] 7821312 512-byte logical blocks: (4.00 GB/3.72 GiB)
[   23.775202] sd 1:0:0:0: [sda] Write Protect is off
[   23.780035] sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
[   23.780704] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   23.799066]  sda: sda1 sda2
[   23.806446] sd 1:0:0:0: [sda] Attached SCSI removable disk
[   23.822374] sd 1:0:0:0: Attached scsi generic sg0 type 0
[   33.098846] EXT2-fs (sda1): warning: mounting ext3 filesystem as ext2
[   34.319206] udevd[230]: starting version 175
[   34.737076] alg: hash: Test 1 failed for mv-hmac-sha1
[   34.749029] 00000000: 0c aa 9f d5 37 c3 79 3a 91 d9 21 5f 42 2b 2c 24
[   34.763993] 00000010: b7 c3 16 0c
[   34.790770] orion_wdt: Initial timeout 21 sec
[   46.946677] NET: Registered protocol family 10
[   47.103956] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
[   47.110053] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   50.857675] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   50.867594] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

HD installed:

# dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.4-kirkwood-tld-1 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 PREEMPT Tue Aug 20 23:25:42 PDT 2013
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Seagate GoFlex Home
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat c05dbf50, node_mem_map c0648000
[    0.000000]   Normal zone: 256 pages used for memap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 117144k/117144k available, 13928k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0561b44   (5479 kB)
[    0.000000]       .init : 0xc0562000 - 0xc05909bc   ( 187 kB)
[    0.000000]       .data : 0xc0592000 - 0xc05de6d0   ( 306 kB)
[    0.000000]        .bss : 0xc05de6d0 - 0xc06470f4   ( 419 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:114
[    0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[    0.000000] Console: colour dummy device 80x30
[   20.478239] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[   20.568060] pid_max: default: 32768 minimum: 301
[   20.568162] Security Framework initialized
[   20.568229] Mount-cache hash table entries: 512
[   20.568835] Initializing cgroup subsys devices
[   20.568858] Initializing cgroup subsys freezer
[   20.568872] Initializing cgroup subsys net_cls
[   20.568882] Initializing cgroup subsys blkio
[   20.568971] CPU: Testing write buffer coherency: ok
[   20.569362] Setting up static identity map for 0xc03e88c8 - 0xc03e8904
[   20.571186] devtmpfs: initialized
[   20.573578] pinctrl core: initialized pinctrl subsystem
[   20.573908] regulator-dummy: no parameters
[   20.574219] NET: Registered protocol family 16
[   20.574642] DMA: preallocated 256 KiB pool for atomic coherent allocations
[   20.575343] Kirkwood: MV88F6281-A1, TCLK=200000000.
[   20.575374] Feroceon L2: Enabling L2
[   20.575412] Feroceon L2: Cache support initialised.
[   20.575742] initial MPP regs: 01111111 11113322 00001111 00100000 00000000 00000000 00000000
[   20.575769]   final MPP regs: 01111111 11113322 00001111 00000000 00000000 00000000 00000000
[   20.579214] bio: create slab <bio-0> at 0
[   20.579632] vgaarb: loaded
[   20.579755] usbcore: registered new interface driver usbfs
[   20.579816] usbcore: registered new interface driver hub
[   20.579914] usbcore: registered new device driver usb
[   20.580512] Switching to clocksource orion_clocksource
[   20.594506] NET: Registered protocol family 2
[   20.595135] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[   20.595170] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[   20.595191] TCP: Hash tables configured (established 1024 bind 1024)
[   20.595258] TCP: reno registered
[   20.595272] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   20.595294] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   20.595491] NET: Registered protocol family 1
[   20.595800] RPC: Registered named UNIX socket transport module.
[   20.595811] RPC: Registered udp transport module.
[   20.595818] RPC: Registered tcp transport module.
[   20.595825] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   20.595836] PCI: CLS 0 bytes, default 32
[   20.596030] Unpacking initramfs...
[   21.137213] Freeing initrd memory: 6324K (c1101000 - c172e000)
[   21.137316] NetWinder Floating Point Emulator V0.97 (double precision)
[   21.137817] audit: initializing netlink socket (disabled)
[   21.137867] type=2000 audit(0.650:1): initialized
[   21.138672] VFS: Disk quotas dquot_6.5.2
[   21.138723] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   21.139079] NFS: Registering the id_resolver key type
[   21.139154] Key type id_resolver registered
[   21.139164] Key type id_legacy registered
[   21.139182] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   21.139334] jffs2: version 2.2. (NAND) (SUMMARY)  \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc.
[   21.139546] msgmni has been set to 241
[   21.141427] alg: No test for stdrng (krng)
[   21.141522] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[   21.141534] io scheduler noop registered
[   21.141542] io scheduler deadline registered
[   21.141568] io scheduler cfq registered (default)
[   21.141688] mv_xor mv_xor.0: Marvell shared XOR driver
[   21.180590] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[   21.220591] mv_xor mv_xor.0: Marvell XOR: ( xor fill cpy )
[   21.220694] mv_xor mv_xor.1: Marvell shared XOR driver
[   21.260589] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[   21.300588] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[   21.300834] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   21.321380] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[   21.818359] console [ttyS0] enabled
[   21.822864] ONFI param page 0 valid
[   21.826369] ONFI flash detected
[   21.829530] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD), 256MiB, page size: 2048, OOB size: 64
[   21.840650] Scanning device for bad blocks
[   22.060084] 4 cmdlinepart partitions found on MTD device orion_nand
[   22.066394] Creating 4 MTD partitions on "orion_nand":
[   22.071583] 0x000000000000-0x000000100000 : "u-boot"
[   22.076796] 0x000000100000-0x000000500000 : "uImage"
[   22.082017] 0x000000500000-0x000002500000 : "rootfs"
[   22.087233] 0x000002500000-0x000010000000 : "data"
[   22.092545] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   22.099105] ehci-pci: EHCI PCI platform driver
[   22.103632] ehci-orion: EHCI orion driver
[   22.107712] orion-ehci orion-ehci.0: EHCI Host Controller
[   22.113174] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   22.121002] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   22.140567] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   22.146594] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   22.153436] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   22.160711] usb usb1: Product: EHCI Host Controller
[   22.165615] usb usb1: Manufacturer: Linux 3.10.4-kirkwood-tld-1 ehci_hcd
[   22.172360] usb usb1: SerialNumber: orion-ehci.0
[   22.177407] hub 1-0:1.0: USB hub found
[   22.181221] hub 1-0:1.0: 1 port detected
[   22.185563] mousedev: PS/2 mouse device common for all mice
[   22.191521] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[   22.197450] i2c /dev entries driver
[   22.201068] cpuidle: using governor ladder
[   22.205183] cpuidle: using governor menu
[   22.209291] leds-gpio leds-gpio: pins are not configured from the driver
[   22.216337] drop_monitor: Initializing network drop monitor service
[   22.222931] TCP: cubic registered
[   22.226262] NET: Registered protocol family 17
[   22.230879] Key type dns_resolver registered
[   22.235569] registered taskstats version 1
[   22.240521] rtc-mv rtc-mv: setting system clock to 2014-01-11 16:46:18 UTC (1389458778)
[   22.249396] Freeing unused kernel memory: 184K (c0562000 - c0590000)
[   22.321239] udevd[52]: starting version 175
[   22.389049] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   22.476178] libphy: PHY orion-mdio-mii:00 not found
[   22.497247] platform mv643xx_eth_port.0: Driver mv643xx_eth_port requests probe deferral
[   22.505469] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   22.515441] SCSI subsystem initialized
[   22.569561] libphy: orion_mdio_bus: probed
[   22.586353] libata version 3.00 loaded.
[   22.599563] sata_mv sata_mv.0: version 1.28
[   22.600410] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 02:50:43:36:64:77
[   22.609280] sata_mv sata_mv.0: cannot get optional clkdev
[   22.626434] sata_mv sata_mv.0: slots 32 ports 1
[   22.652641] scsi0 : sata_mv
[   22.655677] ata1: SATA max UDMA/133 irq 21
[   22.661644] usb 1-1: New USB device found, idVendor=0781, idProduct=556b
[   22.668401] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   22.688410] usb 1-1: Product: Cruzer Edge
[   22.696125] usb 1-1: Manufacturer: SanDisk
[   22.700248] usb 1-1: SerialNumber: 20060774210EFE307EA0
[   22.736639] usb-storage 1-1:1.0: USB Mass Storage device detected
[   22.743069] scsi1 : usb-storage 1-1:1.0
[   22.748446] usbcore: registered new interface driver usb-storage
[   23.000574] ata1: SATA link down (SStatus 0 SControl F300)
[   23.741489] scsi 1:0:0:0: Direct-Access     SanDisk  Cruzer Edge      1.18 PQ: 0 ANSI: 5
[   23.765196] sd 1:0:0:0: [sda] 7821312 512-byte logical blocks: (4.00 GB/3.72 GiB)
[   23.775297] sd 1:0:0:0: [sda] Write Protect is off
[   23.780130] sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
[   23.780797] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   23.799156]  sda: sda1 sda2
[   23.806537] sd 1:0:0:0: [sda] Attached SCSI removable disk
[   23.822438] sd 1:0:0:0: Attached scsi generic sg0 type 0
[   33.098938] EXT2-fs (sda1): warning: mounting ext3 filesystem as ext2
[   34.318127] udevd[230]: starting version 175
[   34.737570] alg: hash: Test 1 failed for mv-hmac-sha1
[   34.744619] 00000000: 0c aa 9f d5 37 c3 79 3a 91 d9 21 5f 42 2b 2c 24
[   34.763742] 00000010: b7 c3 16 0c
[   34.784743] orion_wdt: Initial timeout 21 sec
[   46.980446] NET: Registered protocol family 10
[   47.142327] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
[   47.148420] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   50.875976] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   50.885897] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

optim Wrote:

> Can I hotplug the SATA HD? I can try that and
> look at dmesg if it would help but don't wnat to
> do it if thats a no-no.

Back up the HDD first. For the GoFlex Home/Net, yes should be no problem.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 01/11/2014 09:54AM by bodhi.

from hotplu:

ata1: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen
[ 1551.321115] ata1: edma_err_cause=00000010 pp_flags=00000000, dev connect
[ 1551.327851] ata1: SError: { PHYRdyChg DevExch }
[ 1551.332673] ata1: hard resetting link
[ 1553.680626] ata1: SATA link down (SStatus 0 SControl F300)
[ 1553.686163] ata1: EH complete
[ 1553.868496] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4190000 action 0xe frozen
[ 1553.876104] ata1: edma_err_cause=00000030 pp_flags=00000000, dev connect, SError=04190000
[ 1553.884497] ata1: SError: { PHYRdyChg 10B8B Dispar DevExch }
[ 1553.890201] ata1: hard resetting link
[ 1554.640601] ata1: SATA link down (SStatus 0 SControl F300)
[ 1554.646124] ata1: EH complete

I didn't backup the HD cuz it isn't a big deal if I need to replace everything on it.

It seems to be occasionally resetting now

[ 1596.014795] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen
[ 1596.022478] ata1: edma_err_cause=00000010 pp_flags=00000000, dev connect
[ 1596.029212] ata1: SError: { PHYRdyChg DevExch }
[ 1596.034027] ata1: limiting SATA link speed to 1.5 Gbps
[ 1596.039197] ata1: hard resetting link
[ 1597.190603] ata1: SATA link down (SStatus 0 SControl F310)
[ 1597.196134] ata1: EH complete
[ 1601.438242] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen
[ 1601.445862] ata1: edma_err_cause=00000010 pp_flags=00000000, dev connect
[ 1601.452771] ata1: SError: { PHYRdyChg DevExch }
[ 1601.457337] ata1: limiting SATA link speed to 1.5 Gbps
[ 1601.462737] ata1: hard resetting link
[ 1602.210601] ata1: SATA link down (SStatus 0 SControl F310)
[ 1602.216123] ata1: EH complete
[ 2032.303634] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen
[ 2032.311317] ata1: edma_err_cause=00000010 pp_flags=00000000, dev connect
[ 2032.318054] ata1: SError: { PHYRdyChg DevExch }
[ 2032.322873] ata1: hard resetting link
[ 2033.070602] ata1: SATA link down (SStatus 0 SControl F300)
[ 2033.076130] ata1: EH complete
[ 2725.513925] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen
[ 2725.521582] ata1: edma_err_cause=00000010 pp_flags=00000000, dev connect
[ 2725.528318] ata1: SError: { PHYRdyChg DevExch }
[ 2725.533655] ata1: hard resetting link
[ 2726.680601] ata1: SATA link down (SStatus 0 SControl F300)
[ 2726.686128] ata1: EH complete

Some more errors: I see at least one time it saw the hard drive I didnt notice this when it was active, but now it says its a non-existant drive.



[63764.678293] scsi 0:0:0:0: Direct-Access ATA WDC WD740GD-00FL 31.0 PQ: 0 ANSI: 5
[63764.696148] sd 0:0:0:0: [sdb] 145226112 512-byte logical blocks: (74.3 GB/69.2 GiB)
[63764.704466] sd 0:0:0:0: Attached scsi generic sg1 type 0
[63764.710226] sd 0:0:0:0: [sdb] Write Protect is off
[63764.721225] sd 0:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[63764.755335] sdb: sdb1 sdb2 sdb3
[63764.764178] sd 0:0:0:0: [sdb] Attached SCSI disk

[63763.629344] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen
[63763.637048] ata1: edma_err_cause=00000010 pp_flags=00000000, dev connect
[63763.643974] ata1: SError: { PHYRdyChg DevExch }
[63763.648549] ata1: hard resetting link
[63764.560611] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
[63764.600640] ata1.00: ATA-6: WDC WD740GD-00FLA2, 31.08F31, max UDMA/133
[63764.607206] ata1.00: 145226112 sectors, multi 0: LBA48
[63764.670641] ata1.00: configured for UDMA/133
[63764.674944] ata1: EH complete
[63764.678293] scsi 0:0:0:0: Direct-Access     ATA      WDC WD740GD-00FL 31.0 PQ: 0 ANSI: 5
[63764.696148] sd 0:0:0:0: [sdb] 145226112 512-byte logical blocks: (74.3 GB/69.2 GiB)
[63764.704466] sd 0:0:0:0: Attached scsi generic sg1 type 0
[63764.710226] sd 0:0:0:0: [sdb] Write Protect is off
[63764.721225] sd 0:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[63764.755335]  sdb: sdb1 sdb2 sdb3
[63764.764178] sd 0:0:0:0: [sdb] Attached SCSI disk
[63765.324659] ata1: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
[63765.332259] ata1: edma_err_cause=00000020 pp_flags=00000001, SError=00180000
[63765.339348] ata1: SError: { 10B8B Dispar }
[63765.343725] ata1: hard resetting link
[63765.690603] ata1: SATA link down (SStatus 0 SControl F300)
[63766.300305] ata1: hard resetting link
[63766.650599] ata1: SATA link down (SStatus 0 SControl F300)
[63766.656127] ata1: limiting SATA link speed to 1.5 Gbps
[63767.647549] ata1: hard resetting link
[63768.340628] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F310)
[63768.346961] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
[63768.353474] ata1.00: revalidation failed (errno=-5)
[63768.358374] ata1.00: disabled
[63768.361621] ata1: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen t4
[63768.369229] ata1: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
[63768.376555] ata1: SError: { 10B8B Dispar }
[63768.380845] ata1: hard resetting link
[63768.730602] ata1: SATA link down (SStatus 0 SControl F310)
[63768.736128] ata1: EH complete
[63770.485941] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen
[63770.493692] ata1: edma_err_cause=00000010 pp_flags=00000000, dev connect
[63770.500427] ata1: SError: { PHYRdyChg DevExch }
[63770.505243] ata1: hard resetting link
[63771.850601] ata1: SATA link down (SStatus 0 SControl F300)
[63771.856132] ata1: EH complete
[63771.859123] ata1.00: detaching (SCSI 0:0:0:0)
[63771.869563] sd 0:0:0:0: [sdb] Synchronizing SCSI cache
[63771.880785] sd 0:0:0:0: [sdb]
[63771.883948] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[63771.889983] sd 0:0:0:0: [sdb] Stopping disk
[63771.897593] sd 0:0:0:0: [sdb] START_STOP FAILED
[63771.902558] sd 0:0:0:0: [sdb]
[63771.905721] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[63777.042800] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4190000 action 0xe frozen
[63777.050234] ata1: edma_err_cause=00000010 pp_flags=00000000, dev connect
[63777.057279] ata1: SError: { PHYRdyChg 10B8B Dispar DevExch }
[63777.063168] ata1: hard resetting link
[63777.810604] ata1: SATA link down (SStatus 0 SControl F300)
[63777.816137] ata1: EH complete

Check your hdd with "Data Lifeguard Diagnostic for DOS" (full scan, it will take a while to complete)
http://support.wdc.com/product/download.asp?groupid=612&sid=2&lang=en

I see you are using Western Digital Raptor 10k rpm 74Gb drive through eSATA, has it enough power juice ?
Try changing esata cable, external power supply.

Found similar problem:
https://newit.co.uk/forum/index.php?topic=2684.0;wap2

Quote

Other Linux users seem to have had the same problem which appears to be a kernel bug.

Edited 1 time(s). Last edit at 01/24/2014 05:17AM by jst818.