|
Pogo E02 u-boot envs for LEDE December 22, 2017 08:13AM |
Registered: 10 years ago Posts: 94 |
# envs PogoE02 @debian (checked with uboot.2016.05-tld-1.environment): fw_setenv mtdparts 'mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi)' fw_setenv set_bootargs_lede 'setenv bootargs console=ttyS0,115200 $mtdparts' fw_setenv bootcmd_lede 'run set_bootargs_lede; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000' fw_setenv bootcmd 'run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; run bootcmd_lede'and everthing seems to be fine, boot LEDE from nand / boot debian from stick ....
fw_printenv arcNumber=3542 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; run bootcmd_lede bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_lede=run set_bootargs_lede; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000 bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogo_e02.dtb ethact=egiga0 ethaddr=00:25:31:04:96:8B if_netconsole=ping $serverip init_ide=ide reset init_mmc=mmc rescan init_usb=usb start ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=dd6 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done scan_ide=ide reset scan_mmc=mmc rescan scan_usb=usb start serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params set_bootargs_lede=setenv bootargs console=ttyS0,115200 $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_loaded=0 uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15
|
Re: Pogo E02 u-boot envs for LEDE December 22, 2017 01:51PM |
Admin Registered: 13 years ago Posts: 18,900 |
Quote
if i am on LEDE i cant do a reboot (soft reboot) - cold reboot unplug - plug again works perfect.
|
Re: Pogo E02 u-boot envs for LEDE December 22, 2017 03:18PM |
Registered: 10 years ago Posts: 94 |
[ 99.274476] reboot: Restarting system
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
loading envs from usb 0 ...
** Bad device usb 0 **
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
running scan_disk ...
Scan device usb
device usb 0:1
** Bad device usb 0 **
device usb 1:1
** Bad device usb 1 **
device usb 2:1
** Bad device usb 2 **
device usb 3:1
** Bad device usb 3 **
Scan device ide
Unknown command 'ide' - try 'help'
device ide 0:1
** Bad device ide 0 **
device ide 1:1
** Bad device ide 1 **
device ide 2:1
** Bad device ide 2 **
device ide 3:1
** Bad device ide 3 **
Scan device mmc
Unknown command 'mmc' - try 'help'
device mmc 0:1
** Bad device mmc 0 **
device mmc 1:1
** Bad device mmc 1 **
device mmc 2:1
** Bad device mmc 2 **
device mmc 3:1
** Bad device mmc 3 **
loading uImage ...
** Bad device usb 0 **
loading uInitrd ...
** Bad device usb 0 **
loading DTB /boot/dts/kirkwood-pogo_e02.dtb ...
** Bad device usb 0 **
## Booting kernel from Legacy Image at 00800000 ...
Image Name: ARM LEDE Linux-4.4.92
Created: 2017-10-17 17:46:20 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1810174 Bytes = 1.7 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Using machid 0xdd6 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.92 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Tue Oct 17 17:46:20 2017
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Cloud Engines Pogoplug E02
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi)
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 254500K/262144K available (4082K kernel code, 142K rwdata, 652K rodata, 176K init, 201K bss, 7644K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc04a7db4 (4736 kB)
[ 0.000000] .init : 0xc04a8000 - 0xc04d4000 ( 176 kB)
[ 0.000000] .data : 0xc04d4000 - 0xc04f7bc8 ( 143 kB)
[ 0.000000] .bss : 0xc04f7bc8 - 0xc052a27c ( 202 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000085] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.090090] pid_max: default: 32768 minimum: 301
[ 0.090206] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090224] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090749] CPU: Testing write buffer coherency: ok
[ 0.091091] Setting up static identity map for 0x81e0 - 0x821c
[ 0.091338] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2
[ 0.096004] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.096032] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.096116] pinctrl core: initialized pinctrl subsystem
[ 0.097193] NET: Registered protocol family 16
[ 0.097588] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.098311] cpuidle: using governor ladder
[ 0.098662] Feroceon L2: Enabling L2
[ 0.098707] Feroceon L2: Cache support initialised.
[ 0.098980] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[ 0.116554] SCSI subsystem initialized
[ 0.117279] usbcore: registered new interface driver usbfs
[ 0.117355] usbcore: registered new interface driver hub
[ 0.117423] usbcore: registered new device driver usb
[ 0.118251] clocksource: Switched to clocksource orion_clocksource
[ 0.119133] NET: Registered protocol family 2
[ 0.119731] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.119766] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.119796] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.119853] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.119875] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.120022] NET: Registered protocol family 1
[ 0.121855] Crashlog allocated RAM at address 0x3f00000
[ 0.135827] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.135842] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.138536] io scheduler noop registered
[ 0.138551] io scheduler deadline registered (default)
[ 0.139751] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 0.140314] irq: Cannot allocate irq_descs @ IRQ32, assuming pre-allocated
[ 0.140670] irq: Cannot allocate irq_descs @ IRQ64, assuming pre-allocated
[ 0.172008] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.174985] console [ttyS0] disabled
[ 0.175058] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A
[ 0.626599] console [ttyS0] enabled
[ 0.631795] nand: Could not find valid ONFI parameter page; aborting
[ 0.638229] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 0.644642] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 0.649119] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.656733] Scanning device for bad blocks
[ 0.769162] 2 cmdlinepart partitions found on MTD device orion_nand
[ 0.775455] Creating 2 MTD partitions on "orion_nand":
[ 0.780637] 0x000000000000-0x000000100000 : "u-boot"
[ 0.787319] 0x000000100000-0x000008000000 : "ubi"
[ 0.793935] libphy: orion_mdio_bus: probed
[ 0.798862] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 0.806979] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:96:8b
[ 0.815791] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.822358] ehci-pci: EHCI PCI platform driver
[ 0.826886] ehci-platform: EHCI generic platform driver
[ 0.832281] ehci-orion: EHCI orion driver
[ 0.836464] orion-ehci f1050000.ehci: EHCI Host Controller
[ 0.842019] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 0.849850] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[ 0.868269] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 0.875004] hub 1-0:1.0: USB hub found
[ 0.878983] hub 1-0:1.0: 1 port detected
[ 0.883365] usbcore: registered new interface driver usb-storage
[ 1.198265] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 1.350399] hub 1-1:1.0: USB hub found
[ 1.354493] hub 1-1:1.0: 4 ports detected
[ 1.898261] rtc-mv f1010300.rtc: internal RTC not ticking
[ 1.903783] i2c /dev entries driver
[ 1.908000] orion_wdt: Initial timeout 21 sec
[ 1.915749] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 1.923981] NET: Registered protocol family 10
[ 1.929995] NET: Registered protocol family 17
[ 1.934510] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.947201] 8021q: 802.1Q VLAN Support v1.8
[ 1.953561] UBI: auto-attach mtd1
[ 1.956727] ubi0: attaching mtd1
[ 2.188474] ubi0: scanning is finished
[ 2.203998] ubi0: attached mtd1 (name "ubi", size 127 MiB)
[ 2.209545] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 2.216452] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 2.223191] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[ 2.230016] ubi0: good PEBs: 1016, bad PEBs: 0, corrupted PEBs: 0
[ 2.236134] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 2.243404] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 692591403
[ 2.252498] ubi0: available PEBs: 0, total reserved PEBs: 1016, PEBs reserved for bad PEB handling: 20
[ 2.262222] ubi0: background thread "ubi_bgt0d" started, PID 888
[ 2.268960] block ubiblock0_1: created from ubi0:1(rootfs)
[ 2.274468] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 2.281664] hctosys: unable to open rtc device (rtc0)
[ 2.288241] Waiting 10 sec before mounting root device...
[ 12.298810] VFS: Cannot open root device "LABEL=rootfs" or unknown-block(0,0): error -6
[ 12.306852] Please append a correct "root=" boot option; here are the available partitions:
[ 12.315277] 1f00 1024 mtdblock0 (driver?)
[ 12.320382] 1f01 130048 mtdblock1 (driver?)
[ 12.325464] fe00 1638 ubiblock0_1 (driver?)
[ 12.330739] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 12.339672] Rebooting in 1 seconds..
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
PogoE02> <INTERRUPT>
PogoE02>
|
Re: Pogo E02 u-boot envs for LEDE December 22, 2017 11:38PM |
Admin Registered: 13 years ago Posts: 18,900 |
|
Re: Pogo E02 u-boot envs for LEDE December 23, 2017 05:03AM |
Admin Registered: 13 years ago Posts: 18,900 |
fw_setenv bootcmd_exec 'if run load_uimage; then; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi; fi'
|
Re: Pogo E02 u-boot envs for LEDE December 23, 2017 06:38AM |
Registered: 10 years ago Posts: 94 |
|
Re: Pogo E02 u-boot envs for LEDE December 23, 2017 01:43PM |
Registered: 10 years ago Posts: 94 |
|
Re: Pogo E02 u-boot envs for LEDE December 23, 2017 10:57PM |
Admin Registered: 13 years ago Posts: 18,900 |