Re: revive Medion oxnas stg-212 April 05, 2023 07:55PM |
Registered: 7 years ago Posts: 103 |
Re: revive Medion oxnas stg-212 April 05, 2023 07:56PM |
Registered: 7 years ago Posts: 103 |
Re: revive Medion oxnas stg-212 April 05, 2023 08:21PM |
Admin Registered: 14 years ago Posts: 19,525 |
memtest
Re: revive Medion oxnas stg-212 April 06, 2023 10:03AM |
Registered: 7 years ago Posts: 103 |
OX820> nand erase.part 0 NAND erase.part: device 0 whole chip Skipping bad block at 0x07b20000 Erasing at 0x7fe0000 -- 100% complete. OK OX820> ext2load ide 0:2 61000000 /flash-recovery-hdd/MedionNAS/mtd1.backup 262144 bytes read in 50 ms (5 MiB/s) OX820> nand write 61000000 0 40000 NAND write: device 0 offset 0x0, size 0x40000 262144 bytes written: OK OX820> ext2load ide 0:2 61000000 /flash-recovery-hdd/MedionNAS/mtd2.backup 3670016 bytes read in 482 ms (7.3 MiB/s) OX820> nand write 61000000 40000 380000 NAND write: device 0 offset 0x40000, size 0x380000 3670016 bytes written: OK OX820> ext2load ide 0:2 61000000 /flash-recovery-hdd/MedionNAS/mtd3.data 131094 bytes read in 19 ms (6.6 MiB/s) OX820> nand write 61000000 3C0000 80000 NAND write: device 0 offset 0x3c0000, size 0x80000 524288 bytes written: OK OX820> ext2load ide 0:2 61000000 /flash-recovery-hdd/MedionNAS/mtd4.backup 10485760 bytes read in 1349 ms (7.4 MiB/s) OX820> nand write 61000000 440000 a00000 NAND write: device 0 offset 0x440000, size 0xa00000 10485760 bytes written: OK OX820> ext2load ide 0:2 61000000 /flash-recovery-hdd/MedionNAS/mtd6.backup 10485760 bytes read in 1349 ms (7.4 MiB/s) OX820> nand write 61000000 1840000 a00000 NAND write: device 0 offset 0x1840000, size 0xa00000 10485760 bytes written: OKone restore fails (sysdisk)
OX820> ext2load ide 0:2 61000000 /flash-recovery-hdd/MedionNAS/mtd7.backup 98304000 bytes read in 12499 ms (7.5 MiB/s) OX820> nand write 61000000 2240000 5dc0000 NAND write: device 0 offset 0x2240000, size 0x5dc0000 Attempt to write outside the flash area 0 bytes written: ERRORand then results in well known
Stage-1 Bootloader Tue Aug 9 16:44:00 CST 2011 Attempting to set PLLA to 750MHz ... plla_ctrl0 : 0x0000000A plla_ctrl1 : 0x000F0000 plla_ctrl2 : 0x001D01A0 plla_ctrl3 : 0x00000017 PLLA Set Setup memory, testing Reading NAND, Image 0 Hdr len: 0x0001A94C Hdr CRC: 0xF0019DAC OK U-Boot 1.1.2 (Jun 24 2011 - 09:41:57) U-Boot code: 60D00000 -> 60D1A94C BSS: -> 60D1F004 RAM Configuration: Bank #0: 60000000 128 MB SRAM Configuration: 64KB at 0x50000000 NAND:128 MiB In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0with stock env again
$ printenv bootcmd=run boot_nand bootdelay=2 baudrate=115200 ethaddr=00:30:e0:00:00:01 ipaddr=192.168.50.100 serverip=192.168.50.59 autoload=n netmask=255.255.0.0 bootfile="uImage" load_nand=nboot 61000000 0 440000 boot=bootm 61000000 boot_nand=run load_nand boot MODEL_ID=AB03 PRODUCT_NAME=STG-212 VENDOR_NAME=MitraStar Technology Corp. stdin=serial stdout=serial stderr=serial bootargs= console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=128M poweroutage=yes Environment size: 475/131068 bytesbut still with
Stage-1 Bootloader Tue Aug 9 16:44:00 CST 2011 Attempting to set PLLA to 750MHz ... plla_ctrl0 : 0x0000000A plla_ctrl1 : 0x000F0000 plla_ctrl2 : 0x001D01A0 plla_ctrl3 : 0x00000017 PLLA Set Setup memory, testing Reading NAND, Image 0 Hdr len: 0x0001A94C Hdr CRC: 0xF0019DAC OK U-Boot 1.1.2 (Jun 24 2011 - 09:41:57) U-Boot code: 60D00000 -> 60D1A94C BSS: -> 60D1F004 RAM Configuration: Bank #0: 60000000 128 MB SRAM Configuration: 64KB at 0x50000000 NAND:128 MiB In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0 Loading from device 0: 128MiB 3,3V 8-bit (offset 0x440000) Image Name: Linux-2.6.31.14_SMP_820 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5241420 Bytes = 5 MB Load Address: 60008000 Entry Point: 60008000 ## Booting image at 61000000 ... Image Name: Linux-2.6.31.14_SMP_820 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5241420 Bytes = 5 MB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux.......................................................................................................................................................................................................................................................... crc error -- System haltedsome kind of AAAAAAAHHHHHHHHHHHHHHH!!!!!!!!!!!!!!!!!! still ideas?
Re: revive Medion oxnas stg-212 April 06, 2023 11:10AM |
Registered: 10 years ago Posts: 104 |
Re: revive Medion oxnas stg-212 April 06, 2023 11:17AM |
Registered: 7 years ago Posts: 103 |
OX820> ext2load ide 0:2 61000000 /flash-recovery-hdd/MedionNAS/mtd7.backup 98304000 bytes read in 12499 ms (7.5 MiB/s) OX820> nand write 61000000 2240000 5dbffff NAND write: device 0 offset 0x2240000, size 0x5dbffff Attempt to write outside the flash area 0 bytes written: ERROR
Re: revive Medion oxnas stg-212 April 06, 2023 11:36AM |
Registered: 10 years ago Posts: 104 |
Re: revive Medion oxnas stg-212 April 06, 2023 01:14PM |
Registered: 7 years ago Posts: 103 |
OX820> nand write 61000000 2240000 5da0000 NAND write: device 0 offset 0x2240000, size 0x5da0000 Skip bad block 0x07b20000 98172928 bytes written: OKit doesn't help in running into
Stage-1 Bootloader Tue Aug 9 16:44:00 CST 2011 Attempting to set PLLA to 750MHz ... plla_ctrl0 : 0x0000000A plla_ctrl1 : 0x000F0000 plla_ctrl2 : 0x001D01A0 plla_ctrl3 : 0x00000017 PLLA Set Setup memory, testing Reading NAND, Image 0 Hdr len: 0x0001A94C Hdr CRC: 0xF0019DAC OK U-Boot 1.1.2 (Jun 24 2011 - 09:41:57) U-Boot code: 60D00000 -> 60D1A94C BSS: -> 60D1F004 RAM Configuration: Bank #0: 60000000 128 MB SRAM Configuration: 64KB at 0x50000000 NAND:128 MiB In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0 Loading from device 0: 128MiB 3,3V 8-bit (offset 0x440000) Image Name: Linux-2.6.31.14_SMP_820 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5241420 Bytes = 5 MB Load Address: 60008000 Entry Point: 60008000 ## Booting image at 61000000 ... Image Name: Linux-2.6.31.14_SMP_820 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5241420 Bytes = 5 MB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux.......................................................................................................................................................................................................................................................... crc error -- System haltedi guess NAND is now as stock as possible, what leads me to conclusion of hardware fault - after all those years and countless hours investigating and learning from ground. will try another power supply at home again and of course i'm still up for any advices, tips and hints! :'-(
Re: revive Medion oxnas stg-212 April 06, 2023 01:31PM |
Registered: 7 years ago Posts: 103 |
mtd ~ # cat /proc/mtd dev: size erasesize name mtd0: 08000000 00020000 "NAND 128MiB 3,3V 8-bit" mtd1: 00040000 00020000 "stage1" mtd2: 00380000 00020000 "uboot" mtd3: 00080000 00020000 "uboot_env" mtd4: 00a00000 00020000 "kernel" mtd5: 00a00000 00020000 "etc" mtd6: 00a00000 00020000 "info" mtd7: 05dc0000 00020000 "sysdisk"
Medion-Kernel: static struct mtd_partition partition_info[] = { { .name = "stage1", .offset = 0, .size = 1024 * 128 * 2 /* 2 blocks; 2 stage1 */ }, { .name = "uboot", .offset = MTDPART_OFS_NXTBLK, .size = 1024 * 1024 * 3.5 /* 3.5 MB */ }, { .name = "uboot_env", .offset = MTDPART_OFS_NXTBLK, .size = 1024 * 128 * 4 /* 4 blocks */ }, { .name = "kernel", .offset = MTDPART_OFS_NXTBLK, .size = 1024 * 1024 * 10 /* 10 MB */ }, { .name = "etc", .offset = MTDPART_OFS_NXTBLK, .size = 1024 * 1024 * 10 /* 10 MB */ }, { .name = "info", .offset = MTDPART_OFS_NXTBLK, .size = 1024 * 1024 * 10 /* 10 MB */ }, { .name = "sysdisk", .offset = MTDPART_OFS_NXTBLK, .size = MTDPART_SIZ_FULL /* Should be 93.75 MB */ } };no matter how much i turn things around, file sizes simply don't match size of my NAND... :-?
Re: revive Medion oxnas stg-212 April 06, 2023 02:17PM |
Admin Registered: 14 years ago Posts: 19,525 |
Re: revive Medion oxnas stg-212 April 06, 2023 02:20PM |
Admin Registered: 14 years ago Posts: 19,525 |
Re: revive Medion oxnas stg-212 April 06, 2023 02:36PM |
Admin Registered: 14 years ago Posts: 19,525 |
Quote
no matter how much i turn things around, file sizes simply don't match size of my NAND... :-?
nanddump --noecc --omitoob -f mtd0 /dev/mtd0
Re: revive Medion oxnas stg-212 April 06, 2023 02:51PM |
Registered: 7 years ago Posts: 103 |
U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) Boot device: SATA Attempting to set PLLA to 800 MHz ... plla_ctrl0 : 0000030a plla_ctrl1 : 00400000 plla_ctrl2 : 007f0068 plla_ctrl3 : 00000193 PLLA Set Bus 0: OK Device 0: reading bootargs.bin reading u-boot.img reading u-boot.img U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS DRAM: 128 MiB IDE: Bus 0: OK Device 0: Model: CT1000MX500SSD1 Firm: M3CR032 Ser#: 2037E4AF3A94 Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) NAND: 128 MiB reading u-boot.env In: serial Out: serial Err: serial Net: mii0 ## Error: "safeboot" not defined Hit any key to stop autoboot: 0 4102704 bytes read in 549 ms (7.1 MiB/s) 7033 bytes read in 11 ms (624 KiB/s) magic: 0xd00dfeed totalsize: 0x1b79 (7033) off_dt_struct: 0x38 off_dt_strings: 0x18d4 off_mem_rsvmap: 0x28 version: 17 last_comp_version: 16 boot_cpuid_phys: 0x0 size_dt_strings: 0x2a5 size_dt_struct: 0x189c number mem_rsv: 0x0 ## Booting kernel from Legacy Image at 60000000 ... Image Name: Linux-3.17.0-oxnas-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4102640 Bytes = 3.9 MiB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 61000000 Booting using the fdt blob at 0x61000000 Loading Kernel Image ... OK Loading Device Tree to 67e26000, end 67e2ab78 ... OK Starting kernel ... Uncompressing Linux... uncompression error -- System halted
Re: revive Medion oxnas stg-212 April 06, 2023 03:13PM |
Admin Registered: 14 years ago Posts: 19,525 |
Re: revive Medion oxnas stg-212 April 06, 2023 03:16PM |
Registered: 7 years ago Posts: 103 |
Re: revive Medion oxnas stg-212 April 06, 2023 03:25PM |
Admin Registered: 14 years ago Posts: 19,525 |
Re: revive Medion oxnas stg-212 April 06, 2023 08:02PM |
Registered: 7 years ago Posts: 103 |
Re: revive Medion oxnas stg-212 April 06, 2023 08:16PM |
Admin Registered: 14 years ago Posts: 19,525 |
help
Re: revive Medion oxnas stg-212 April 07, 2023 05:18AM |
Registered: 7 years ago Posts: 103 |
> help
$ help ? - alias for 'help' base - print or set address offset bdinfo - print Board Info structure bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol cmp - memory compare cp - memory copy crc32 - checksum calculation echo - echo args to console exit - exit script go - start application at address 'addr' help - print online help iminfo - print header information for application image ledfail - Extinguish (0) or light (1) failure LED loop - infinite loop on address range md - memory display mm - memory modify (auto-incrementing) mtest - simple RAM test mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nm - memory modify (constant address) nwboot - NAND Write boot information ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU run - run commands in an environment variable saveenv - save environment variables to persistent storage setenv - set environment variables test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol version - print monitor version> All it matter is root=LABEL=rootfs. And
setenv tftp_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' setenv load_uimage 'tftp 0x800000 uImage' setenv load_uinitrd 'tftp 0x2100000 uInitrd' setenv tftp_boot 'mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000' setenv tftp_bootcmd 'run tftp_set_bootargs; run tftp_boot' setenv bootcmd 'run tftp_bootcmd'
Re: revive Medion oxnas stg-212 April 07, 2023 07:04AM |
Registered: 7 years ago Posts: 103 |
Stage-1 Bootloader Tue Aug 9 16:44:00 CST 2011 Attempting to set PLLA to 750MHz ... plla_ctrl0 : 0x0000000A plla_ctrl1 : 0x000F0000 plla_ctrl2 : 0x001D01A0 plla_ctrl3 : 0x00000017 PLLA Set Setup memory, testing Reading NAND, Image 0 Hdr len: 0x0001A94C Hdr CRC: 0xF0019DAC OK U-Boot 1.1.2 (Jun 24 2011 - 09:41:57) U-Boot code: 60D00000 -> 60D1A94C BSS: -> 60D1F004 RAM Configuration: Bank #0: 60000000 128 MB SRAM Configuration: 64KB at 0x50000000 NAND:128 MiB In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0 $ setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' $ printenv bootcmd=run boot_nand bootdelay=2 baudrate=115200 ipaddr=192.168.50.100 serverip=192.168.50.59 autoload=n netmask=255.255.0.0 bootfile="uImage" load_nand=nboot 61000000 0 440000 boot=bootm 61000000 boot_nand=run load_nand boot MODEL_ID=AB03 PRODUCT_NAME=STG-212 VENDOR_NAME=MitraStar Technology Corp. ethaddr=00:11:41:30:3A:12 stdin=serial stdout=serial stderr=serial bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial Environment size: 448/131068 bytes $ mw 0x800000 0 1 $ tftp 0x800000 uImage Wait GMAC to reset Wait for PHY reset. PHY is Realtek RTL8211E Wait for link to come up..........Link up Wait for auto-negotiation to complete Link is 1000M TFTP from server 192.168.50.59; our IP address is 192.168.50.100 Filename 'uImage'. Load address: 0x800000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## done Bytes transferred = 4609927 (465787 hex) $ tftp 0x2100000 uInitrd Wait GMAC to reset Wait for PHY reset. PHY is Realtek RTL8211E Wait for link to come up..........Link up Wait for auto-negotiation to complete Link is 1000M TFTP from server 192.168.50.59; our IP address is 192.168.50.100 Filename 'uInitrd'. Load address: 0x2100000 Loading: ################################################################# ################################################################# ################################################################# ##########data abort pc : [<60d10034>] lr : [<60d02894>] sp : 60cbf554 ip : 00000000 fp : 60cbffb8 r10: 60ce2512 r9 : 00000fff r8 : 60cbffdc r7 : 00000202 r6 : 0000e458 r5 : 00100200 r4 : 00000200 r3 : 0000003f r2 : 000001ff r1 : 60ce2540 r0 : 02200000 Flags: nzCv IRQs off FIQs off Mode SVC_32 Resetting CPU ...crashing while loading Debian-4.14.180-oxnas-tld-1-rootfs-bodhi/boot/uInitrd.
Re: revive Medion oxnas stg-212 April 07, 2023 08:34AM |
Registered: 7 years ago Posts: 103 |
Stage-1 Bootloader Tue Aug 9 16:44:00 CST 2011 Attempting to set PLLA to 750MHz ... plla_ctrl0 : 0x0000000A plla_ctrl1 : 0x000F0000 plla_ctrl2 : 0x001D01A0 plla_ctrl3 : 0x00000017 PLLA Set Setup memory, testing Reading NAND, Image 0 Hdr len: 0x0001A94C Hdr CRC: 0xF0019DAC OK U-Boot 1.1.2 (Jun 24 2011 - 09:41:57) U-Boot code: 60D00000 -> 60D1A94C BSS: -> 60D1F004 RAM Configuration: Bank #0: 60000000 128 MB SRAM Configuration: 64KB at 0x50000000 NAND:128 MiB In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0 $ setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' $ tftp 0x60000000 uImage Wait GMAC to reset Wait for PHY reset. PHY is Realtek RTL8211E Wait for link to come up...........Link up Wait for auto-negotiation to complete Link is 1000M TFTP from server 192.168.50.59; our IP address is 192.168.50.100 Filename 'uImage'. Load address: 0x60000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## done Bytes transferred = 4609927 (465787 hex) $ tftp 0x61000000 uInitrd Wait GMAC to reset Wait for PHY reset. PHY is Realtek RTL8211E Wait for link to come up..........Link up Wait for auto-negotiation to complete Link is 1000M TFTP from server 192.168.50.59; our IP address is 192.168.50.100 Filename 'uInitrd'. Load address: 0x61000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################ done Bytes transferred = 6464907 (62a58b hex) $ bootm 0x60000000 0x61000000 ## Booting image at 60000000 ... Image Name: Linux-4.14.180-oxnas-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4609863 Bytes = 4.4 MB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 61000000 ... Image Name: initramfs-4.14.180-oxnas-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6464843 Bytes = 6.2 MB Load Address: 60000000 Entry Point: 60000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... uncompression error -- System halted
Re: revive Medion oxnas stg-212 April 07, 2023 02:47PM |
Admin Registered: 14 years ago Posts: 19,525 |
load_initrd=echo loading uInitrd ...; load $bootdev $device 0x60e00000 /boot/uInitrd load_uimage=echo loading uImage ...; load $bootdev $device 0x60500000 /boot/uImage
tftp 0x60500000 uImage bootm 0x60500000
Re: revive Medion oxnas stg-212 April 07, 2023 03:06PM |
Registered: 7 years ago Posts: 103 |
Stage-1 Bootloader Tue Aug 9 16:44:00 CST 2011 Attempting to set PLLA to 750MHz ... plla_ctrl0 : 0x0000000A plla_ctrl1 : 0x000F0000 plla_ctrl2 : 0x001D01A0 plla_ctrl3 : 0x00000017 PLLA Set Setup memory, testing Reading NAND, Image 0 Hdr len: 0x0001A94C Hdr CRC: 0xF0019DAC OK U-Boot 1.1.2 (Jun 24 2011 - 09:41:57) U-Boot code: 60D00000 -> 60D1A94C BSS: -> 60D1F004 RAM Configuration: Bank #0: 60000000 128 MB SRAM Configuration: 64KB at 0x50000000 NAND:128 MiB In: serial Out: serial Err: serial Setting Linux mem= boot arg value Hit any key to stop autoboot: 0
$ setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
$ printenv bootcmd=run boot_nand bootdelay=2 baudrate=115200 ipaddr=192.168.50.100 serverip=192.168.50.59 autoload=n netmask=255.255.0.0 bootfile="uImage" load_nand=nboot 61000000 0 440000 boot=bootm 61000000 boot_nand=run load_nand boot MODEL_ID=AB03 PRODUCT_NAME=STG-212 VENDOR_NAME=MitraStar Technology Corp. ethaddr=00:11:41:30:3A:12 stdin=serial stdout=serial stderr=serial bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial Environment size: 448/131068 bytes
$ tftp 0x60500000 uImage Wait GMAC to reset Wait for PHY reset. PHY is Realtek RTL8211E Wait for link to come up..........Link up Wait for auto-negotiation to complete Link is 1000M TFTP from server 192.168.50.59; our IP address is 192.168.50.100 Filename 'uImage'. Load address: 0x60500000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## done Bytes transferred = 4609927 (465787 hex)
$ tftp 0x60e00000 uInitrd Wait GMAC to reset Wait for PHY reset. PHY is Realtek RTL8211E Wait for link to come up..........Link up Wait for auto-negotiation to complete Link is 1000M TFTP from server 192.168.50.59; our IP address is 192.168.50.100 Filename 'uInitrd'. Load address: 0x60e00000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################ done Bytes transferred = 6464907 (62a58b hex)
$ bootm 0x60500000 ## Booting image at 60500000 ... Image Name: Linux-4.14.180-oxnas-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4609863 Bytes = 4.4 MB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... uncompression error -- System halted
Re: revive Medion oxnas stg-212 April 07, 2023 03:30PM |
Admin Registered: 14 years ago Posts: 19,525 |
load_nand=nboot 61000000 0 440000 boot=bootm 61000000
tftp 0x61000000 uImage bootm 61000000
Re: revive Medion oxnas stg-212 April 07, 2023 03:45PM |
Registered: 7 years ago Posts: 103 |
$ tftp 0x61000000 uImage Wait GMAC to reset Wait for PHY reset. PHY is Realtek RTL8211E Wait for link to come up..........Link up Wait for auto-negotiation to complete Link is 1000M TFTP from server 192.168.50.59; our IP address is 192.168.50.100 Filename 'uImage'. Load address: 0x61000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## done Bytes transferred = 4609927 (465787 hex) $ bootm 61000000 ## Booting image at 61000000 ... Image Name: Linux-4.14.180-oxnas-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4609863 Bytes = 4.4 MB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... uncompression error -- System halted:-(
Re: revive Medion oxnas stg-212 April 07, 2023 03:54PM |
Admin Registered: 14 years ago Posts: 19,525 |
Re: revive Medion oxnas stg-212 April 07, 2023 03:56PM |
Registered: 8 years ago Posts: 376 |
Re: revive Medion oxnas stg-212 April 07, 2023 04:01PM |
Registered: 7 years ago Posts: 103 |
mtest 60000000 7FE0000it is reading and writing circulation pattern non stop until i ^C. I didn't find anything explaining on the net, how it should work - which behaviour to expect, when it's finished and so on. So not very helpful to me to this point.
Re: revive Medion oxnas stg-212 April 07, 2023 04:12PM |
Registered: 7 years ago Posts: 103 |
Re: revive Medion oxnas stg-212 April 07, 2023 04:41PM |
Admin Registered: 14 years ago Posts: 19,525 |