Dear bodhi, It is working! Thank you very much. Best regards, pepeszby pepesz - uBoot
Dear all, I just flashed the uboot to nand. # ./tools/flash_erase /dev/mtd0 0 4 Erase Total 4 Units Performing Flash Erase of length 131072 at offset 0x60000 done # ./tools/nandwrite /dev/mtd0 uboot.2013.10-tld-1.nsa325.mtd0.kwb Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000 I do not see any errors but Iby pepesz - uBoot
OK, it's solved. I set the envs as follow: usb_init=usb start usb_root=LABEL=rootfs usb_root was previously set to /dev/sda1 while my system is on /dev/sda2 Looks like I can try to flash it to nand. Thanks a lot!! pepeszby pepesz - uBoot
hello, after setting setenv usb_init "run usb_scan; setenv usb_root LABEL=rootfs" i got: Hit any key to stop autoboot: 0 ## Error: "usb_scan" not defined ** Bad device usb 0 ** ** Bad device usb 0 ** cheers, pepeszby pepesz - uBoot
Hello, I'm a bit further [ 7.367971] hub 3-0:1.0: USB hub found [ 7.371773] hub 3-0:1.0: 2 ports detected [ 7.654721] ata1: SATA link down (SStatus 0 SControl F300) [ 8.024714] ata2: SATA link down (SStatus 0 SControl F300) [ 8.885543] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 6 [ 8.918013] sd 2:0:0:0: 30490624 512-byte logical blby pepesz - uBoot
Thanks, One step further, but still no success. The booting stops (hangs) at: [ 7.197224] usbcore: registered new interface driver uas I tried two different usb flash disks, both with same results. full log at http://pastebin.com/UvU2uFA5 best regards, pepeszby pepesz - uBoot
Dear bodhi, NSA325> usb part Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 11 195283 34362054-01 83 Boot 2 195294 30295330 34362054-02 83 NSA325> ext2ls usb 0:1 /boot ** Can not find directory. ** but NSA325> ext2ls usb 0:1 / <DIR>by pepesz - uBoot
Dear bodhi, NSA325> usb start (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found NSA325> ext2ls usb 0:1 /boot ** Can not find directory. ** NSA325> printenv arcNumber=4495 baudrate=115200 bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset bootcmd_mby pepesz - uBoot
dear bodhi, I'm new to the nsa325. I followed the instruction in http://forum.doozan.com/read.php?2,14351, and I have debian running from usb, no problem there. Next step is upgrading the uboot as I mention before. The new uboot image is loaded via uart but doesn't see the boot images? QuoteLook in your USB rootfs. Not sure what I'm supposed to see there - the /boot/uby pepesz - uBoot