sorry about the confusion i was able to make a usb bootfs i was attempting to transfer or make a SD bootfsby hbelcher - uBoot
it boots like this with the usb just fineby hbelcher - uBoot
Pogov4> printenv CASset=min MALLOC_len=1 apt-setup/local0/key=http://people.debian.org/~tbm/orion/68FD549F arcNumber=2097 baudrate=115200 boot=bootm 0x800000 boot_nand=run load_nand boot bootargs=console=ttyS0,115200 base-installer/initramfs-tools/driver-policy=most mirror/suite=stable apt-setup/local0/repository=http://people.debian.org/~tbm/orion/lenny/main apt-setup/local0/key=hby hbelcher - uBoot
well after a lot of help its booting from usb :) now i want to boot from SD i have updated the uboot it starts to boot then 10.780619] mmc0: host does not support reading read-only switch, assuming write-enable [ 10.792789] mmc0: new high speed SDHC card at address 0001 [ 10.799079] mmcblk0: mmc0:0001 AS 3.70 GiB [ 10.804735] mmcblk0: p1 [ 20.780907] VFS: Cannot opby hbelcher - uBoot
bodhi Wrote: ------------------------------------------------------- > Recreate the Debian 4.4 rootfs and boot with it > > - plug in the Debian 4.4 USB rootfs > - power up, interrupt serial console, and > > > printev CASset=min MALLOC_len=1 apt-setup/local0/key=http://people.debian.org/~tbm/orion/68FD549F arcNumber=2097 baudrate=115200 boot=bootm 0x800000by hbelcher - uBoot
well im still at the "kind of " booting i have tried to mount the usb or even fdisk the they appears not to be loaded here is the guide i was trying to use wiki.xkyle.com/Install_Debian_on_a_Pogoplug.html but something is not working i was just grasping at anything to try to make a usb drive roofs and thought if i could boot up on the pogo i could make a usb or sd heby hbelcher - uBoot
i was able to boot via tftp server tftpboot 0x01100000 uInitrd tftpboot 0x00800000 uImage bootm 0x00800000 0x01100000 still trying to figure out why i cant make a valid fs diskby hbelcher - uBoot
i have setup tftp and tested it just need something to send to to pogoplugby hbelcher - uBoot
well i think i have most of the env Pogov4> printenv CASset=min MALLOC_len=1 arcNumber=3960 baudrate=115200 boot=bootm 0x800000 boot_nand=run load_nand boot bootargs=console $(console) root LABEL rootfs rootdelay 10 $(mtdparts) $(custom_params) bootargs_console=console=ttyS0,115200 bootcmd=run set_bootargs; run bootcmd_exec; reset bootcmd_exec=mw 0x800000 0 1 bootcmd_mmc=mby hbelcher - uBoot
i cant seem to boot to usb ( getting errors when i tar the image) and all i get is a loop U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Unknown command 'load_uimage'by hbelcher - uBoot
good thanks for your help now after attempting to update uboot im stick here U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 No link on egiga0 Wrong Image Format for bootm cby hbelcher - uBoot
can i recover from this? "Disk /dev/mtd4: 0 MB, 0 bytes 255 heads, 63 sectors/track, 0 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk /dev/mtd4 doesn't contain a valid partition table"by hbelcher - uBoot
thanks for the help i have made the changes you suggested now to make the usb to boot with CE>> printenv baudrate=115200 loads_echo=0 ipaddr=169.254.254.253 serverip=169.254.254.254 rootpath=/mnt/ARM_FS/ netmask=255.255.0.0 run_diag=yes stdin=serial stdout=serial stderr=serial CASset=min enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2Cacby hbelcher - uBoot
i think i may have defaulted them it doesn't seem to be booting from the usb anymore i think its booting back into stockby hbelcher - uBoot
CE>> printenv baudrate=115200 loads_echo=0 ipaddr=169.254.254.253 serverip=169.254.254.254 rootpath=/mnt/ARM_FS/ netmask=255.255.0.0 run_diag=yes stdin=serial stdout=serial stderr=serial mainlineLinux=no CASset=min enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes MALLOby hbelcher - uBoot
ok im to here now but it freezes here "[ 127.171733] random: nonblocking pool is initialized" U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFD60 Soc: 88F6192 A1 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit wiby hbelcher - uBoot
ok i did the best i could to follow the directions but i still have a problem i downloaded the tar formatted the usb stick to ex3 extracted the "Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2" to the usb stick then i connected a serial connection to the board and opened putty here is what i get U-Boot 1.1.4 (Oct 1 2011 - 12:21:35) Cloud Engines 1.1.2 (3.4.27) Pby hbelcher - uBoot
looks like i will be opening this up and connecting a serial connection to it so i can see whats going on inside i will let you know what i find outby hbelcher - uBoot
a friend gave me his pogoplug but didnt have the usb drive he was booting from i need a bootable usb drive image i can start with all the pogoplug does is the green led flashes he told me he had it set to boot from the usb drive so im guessing its looking for a boot image from the usb its not pulling an ip from the dhcp server so im pretty sure its not booting thanks for any heby hbelcher - uBoot