Welcome! Log In Create A New Profile

Advanced

Hello, help to fix my device... [Akitio MyCloud Mini]

Posted by Kang Jinsu 
Hello, help to fix my device... [Akitio MyCloud Mini]
May 09, 2020 12:47AM
Hello, i am from korea.

I tried to install on this device.
I install a new bootloader on this device.
But I made a mistake.
This device is not backed up properly.
So the NAND drive doesn't boot at all.
Only the spl area is displayed from NAND drive.

So, I made a new attempt.
Try booting to s-ata.
Initially, it does not boot well.
After several attempts, u-boot succeeded.
However, it started to get blocked from `Uncompressing Linux ... done, booting the kernel.`.
I tried formatting and reinstalling the s-ata disk, but it didn't work at all.

See here : https://forum.doozan.com/read.php?3,42599

Is this possible only with pogoplug v3?
What should I do?

Thanks for the help.

(Sorry my English, help with translator)

Device log :

[If unplugged s-ata drive]

U-Boot SPL 2013.10-tld-4 (Sep 07 2014 - 14:10:12)
  Boot device: NAND
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set


[If plugged s-ata drive]

U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
  Boot device: SATA
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK 
  Device 0: 
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM:  256 MiB
IDE:   Bus 0: OK 
  Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   
Led:	GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0 
ide - IDE sub-system

Usage:
ide reset - reset IDE controller
ide info  - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read  addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
    to/from memory address `addr'
4102704 bytes read in 656 ms (6 MiB/s)
1953812 bytes read in 353 ms (5.3 MiB/s)
7816 bytes read in 65 ms (117.2 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-3.17.0-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4102640 Bytes = 3.9 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
   Image Name:   initramfs-3.17.0-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    1953748 Bytes = 1.9 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
   Booting using the fdt blob at 0x62c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 6fc4b000, end 6fe27fd4 ... OK
   Loading Device Tree to 6fc46000, end 6fc4ae87 ... OK

Led:	GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

======
moderator edit: please use Formatted Code to post log.



Edited 1 time(s). Last edit at 05/09/2020 01:54AM by bodhi.
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 09, 2020 02:25AM
Kang Jinsu,

Take a look at this post, see if you can retrace the steps that you did to create the SATA drive boot files:

https://forum.doozan.com/read.php?3,93499,93729#msg-93729

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 09, 2020 05:16AM
Yes. After doing the content in the link above, it seems to boot.

U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
  Boot device: SATA
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK 
  Device 0: 
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM:  256 MiB
IDE:   Bus 0: OK 
  Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   
Led:	GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0 
ide - IDE sub-system

Usage:
ide reset - reset IDE controller
ide info  - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read  addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
    to/from memory address `addr'
2212156 bytes read in 339 ms (6.2 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-2.6.31.14_OX820_1.2_shv
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2212092 Bytes = 2.1 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Led:	GREEN

Starting kernel ...

Uncompressing Linux....................................................................................................................................... done, booting the kernel.
[    0.000000] Linux version 2.6.31.14_OX820_1.2_shv (root@plug2) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP Fri Oct 4 11:38:10 CEST 2013
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: Oxsemi NAS
[    0.000000] 1 memory region
[    0.000000] Ignoring unrecognised tag 0x00000000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: root=/dev/sda2 rootfstype=ext3 console=ttyS0,115200 mem=128M
[    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 125368KB available (3816K code, 304K data, 132K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:96
[    0.000000] OX820_RPS_init_irq: interrupts 64 to 96
[    0.010000] Console: colour dummy device 80x30
[    0.010000] console [ttyS0] enabled
[    0.020000] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.230000] Security Framework initialized
[    0.230000] Mount-cache hash table entries: 512
[    0.240000] CPU: Testing write buffer coherency: ok
[    0.240000] Calibrating local timer... 425.50MHz.
[   s0.3000[] CrU1: Boo�ed�secondary prcessor
�6>[   S.41000[� Calibrati�g delay loop�..n<�>3�9.�4 BogoMIPS (pj=1695�44�
[    0.620000] Brought up 2 CPUs
[    0.630000] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[    0.640000] NET: Registered protocol family 16
[    0.640000] Number of DMA channels = 4, version = 4
[    0.650000] Reserving a DMA channel for DirectRAID
[    0.650000] Allocating 389 SRAM generic DMA descriptors


And, there is no reaction from here.
What should I do from here?

Change bootloader options?
The contents of that post should not change the kernel file,
Even if I change dtb file in option, this state.

*Edit*



Edited 1 time(s). Last edit at 05/09/2020 06:59AM by Kang Jinsu.
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 09, 2020 04:19PM
Kang Jinsu,

I see. Since this is the Atikio MyCloud, not Pogo V3 Oxnas, there is some difference that coud have prevented it from booting. This kernel 2.6.x is quite old and built specifically for Pogo V3 Pro.

It is quicker to recover by flashing u-boot to NAND to fix the booting problem. And then create a new rootfs on USB usinng Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2. .

See here for how to reflash this u-boot in serial console:

https://forum.doozan.com/read.php?3,42599,44024#msg-44024

You should follow section A.

Quote

A. Using an HDD attached to the SATA port

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 10, 2020 12:06AM
I saw well. I tried as per the above.

But completely broken.
No reaction at all.
I have to get the SPL phrase yesterday, but now there is no phrase at all.

I think I came too far.
There is more work.

Thanks for your help.
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 10, 2020 12:24AM
Ask carefully. I think I made a serious mistake.

I no longer use stock firmware.
So it doesn't matter if the stock firmware doesn't work.

I deleted NAND all before recording u-boot.
I think the records from the beginning are wrong and conflict with each other.

It records, but it still won't boot from NAND.



Edited 1 time(s). Last edit at 05/10/2020 12:24AM by Kang Jinsu.
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 10, 2020 03:54AM
Kang Jinsu,

If flashing new u-boot does not work out, then go back to booting with HDD directly.

And then use the latest rootfs Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2.

https://forum.doozan.com/read.php?2,16044


Extract it to the HDD where the rootfs is currently is. And then copy uImage and uInird to /boot, copy the DTB to /boot/dts.

drwxr-xr-x 2 root root    4096 aug  3  2014 dts
-rw-r--r-- 1 root root 3676848 aug  3  2014 uImage
-rw-r--r-- 1 root root 2103272 aug  3  2014 uInitrd

After that power up and interrupt serial console,

printenv
boot

And post the entire serial console log here. Don't describe what happen, I need to see the log to understand where you are.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 10, 2020 04:35AM
Here serial console logs.


U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
  Boot device: SATA
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK 
  Device 0: 
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM:  256 MiB
IDE:   Bus 0: OK 
  Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   
Led:	GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0 
OX820 # printenv
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200n8
bootcmd=run dt_bootcmd_ide
bootdelay=3
console=console=ttyS0,115200n8
dt_bootcmd_ide=ide start; run dt_ide_bootcmd; ide stop; reset
dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
dt_ide_boot=run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm
dt_ide_bootcmd=run ide_set_bootargs; run dt_sata_boot
dt_ide_load_dtb=ext2load ide 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb
dt_ide_load_initrd=ext2load ide 0:1 $uinitrd_addr /boot/uInitrd
dt_ide_load_uimage=ext2load ide 0:1 $uimage_addr /boot/uImage
dt_load_dtb=ext2load usb 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb
dt_load_initrd=ext2load usb 0:1 $uinitrd_addr /boot/uInitrd
dt_load_uimage=ext2load usb 0:1 $uimage_addr /boot/uImage
dt_sata_boot=ext2load ide 0:1 $uimage_addr /boot/uImage_2.6.31.14_OX820_1.2_shv.Pro; bootm $uimage_addr
dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm
dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot
dtb_addr=0x62c00000
ethact=mii0
ethaddr=00:01:D2:12:27:07
ide_set_bootargs=setenv bootargs root=/dev/sda1 rootfstype=ext3 console=ttyS0,115200 mem=256M
if_netconsole=ping $serverip
ipaddr=192.168.68.76
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
preboot_nc=run if_netconsole start_netconsole
sata_bootcmd=run usb_set_bootargs; run sata_boot
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version
stderr=serial
stdin=serial
stdout=serial
uimage_addr=0x60500000
uinitrd_addr=0x60e00000
usb_device=0:1
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10

Environment size: 1886/16380 bytes
OX820 # boot
ide - IDE sub-system

Usage:
ide reset - reset IDE controller
ide info  - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read  addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
    to/from memory address `addr'
2212156 bytes read in 351 ms (6 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-2.6.31.14_OX820_1.2_shv
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2212092 Bytes = 2.1 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Led:	GREEN

Starting kernel ...

Uncompressing Linux....................................................................................................................................... done, booting the kernel.
[    0.000000] Linux version 2.6.31.14_OX820_1.2_shv (root@plug2) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP Fri Oct 4 11:38:10 CEST 2013
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: Oxsemi NAS
[    0.000000] 1 memory region
[    0.000000] Ignoring unrecognised tag 0x00000000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: root=/dev/sda1 rootfstype=ext3 console=ttyS0,115200 mem=256M
[    0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 256MB = 256MB total
[    0.000000] Memory: 255232KB available (3816K code, 304K data, 132K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:96
[    0.000000] OX820_RPS_init_irq: interrupts 64 to 96
[    0.010000] Console: colour dummy device 80x30
[    0.010000] console [ttyS0] enabled
[    0.020000] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.230000] Security Framework initialized
[    0.230000] Mount-cache hash table entries: 512
[    0.240000] CPU: Testing write buffer coherency: ok
[    0.240000] Calibrating local timer... 424.49MHz.
[   0.310000] CrU1� Booted seconday processor
[    0.40000] C�librating delay loop...<�>339.14 BogoM�PS (lpj1695744)
[    0.620000] Brought up 2 CPUs
[    0.630000] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[    0.640000] NET: Registered protocol family 16
[    0.640000] Number of DMA channels = 4, version = 4
[    0.650000] Reserving a DMA channel for DirectRAID
[    0.650000] Allocating 389 SRAM generic DMA descriptors

*edit : serial codes -> serial console logs



Edited 1 time(s). Last edit at 05/10/2020 04:38AM by Kang Jinsu.
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 10, 2020 04:37PM
Kang Jinsu,

Your current envs still try to boot with the old kernel. We're going to try booting with the new kernel.

Boot with HDD again. Interrupt serial console and
run dt_ide_boot

And post the entire serial console log here.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 10, 2020 10:32PM
Here serial console log.

Bus 0: OK
  Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:
Led:    GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0
OX820 # run dt_ide_boot
4621824 bytes read in 715 ms (6.2 MiB/s)
4594376 bytes read in 680 ms (6.4 MiB/s)
7816 bytes read in 46 ms (165 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4621760 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
   Image Name:   initramfs-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4594312 Bytes = 4.4 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
   Booting using the fdt blob at 0x62c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 6f9c7000, end 6fe28a88 ... OK
   Loading Device Tree to 6f9c2000, end 6f9c6e87 ... OK

Led:    GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.


Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 10, 2020 11:38PM
OK. Try,


setenv bootcmd 'run dt_bootcmd_ide'
setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset'
setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 rootfstype=ext3 console=ttyS0,115200 mem=256M earlyprintk=serial'
setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm'
setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
boot

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 10, 2020 11:46PM
Wow, This will make it boot.
However, it stops in the middle.

Here serial console logs.


U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
  Boot device: SATA
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK
  Device 0:
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM:  256 MiB
IDE:   Bus 0: OK
  Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:
Led:    GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0
OX820 # setenv bootcmd 'run dt_bootcmd_ide'
OX820 # setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset'
OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
OX820 # setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 rootfstype=ext3 console=ttyS0,115200 mem=256M earlyprintk=serial'
OX820 # setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # boot
ide - IDE sub-system

Usage:
ide reset - reset IDE controller
ide info  - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read  addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
    to/from memory address `addr'
4621824 bytes read in 704 ms (6.3 MiB/s)
4594376 bytes read in 677 ms (6.5 MiB/s)
7816 bytes read in 46 ms (165 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4621760 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
   Image Name:   initramfs-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4594312 Bytes = 4.4 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
   Booting using the fdt blob at 0x62c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
   Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK

Led:    GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Akitio MyCloud mini
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[    0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: root=/dev/sda1 rootfstype=ext3 console=ttyS0,115200 mem=256M earlyprintk=serial
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 246148K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15996K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff800000   ( 752 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0827e14   (8320 kB)
[    0.000000]       .init : 0xc0828000 - 0xc0860000   ( 224 kB)
[    0.000000]       .data : 0xc0860000 - 0xc08a8378   ( 289 kB)
[    0.000000]        .bss : 0xc08a8378 - 0xc08e6350   ( 248 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:160
[    0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000007] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.008335] Console: colour dummy device 80x30
[    0.012894] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.072586] pid_max: default: 32768 minimum: 301
[    0.077424] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.084129] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.092039] Initializing cgroup subsys net_cls
[    0.096611] CPU: Testing write buffer coherency: ok
[    0.101995] Setting up static identity map for 0x60008220 - 0x60008258
[   40.23987] Unable to handle kernelaNULL pointer dereferencb at virtual addres4 0000000
[   00.23992] Brought up 2 CPUs
[   30.23993] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[   40.24060] devtmpfs: initialized
[   00.25038] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[   40.25041] futex hash table entries: 512 (order: 2, 16384 bytes)
[   00.25069] prandom: seed boundary self test passed
[   20.25504] prandom: 100 self tests passed
[   70.25505] pinctrl core: initialized pinctrl subsystem
[   20.25590] NET: Registered protocol family 16
[   10.25648] DMA: preallocated 256 KiB pool for atomic coherent allocations
[   0.30253▒] pgd = c000400
[   0.305310] ▒[00000000] *pgd00000000
[   ▒0.30913] Internal error:1Oo:s: 5 [#p] PREEMPT SMP ARM
[   60.31449] Modules linked in:
[   ▒0.317616] ▒CP1: 1 PID3 0 Comm▒ swapper/1 Not taint▒d 4.4.54-oxnas-tld1 #2
[   0.324794] ▒Hardware name: PLXnECH NAS782X SoC (Flattened Device Tree)
[   30.33154] task: cf046d00 ti:cf06a00A task.t : cf06a000
[   ▒0.33717▒] PC is at _raw_spin_lo▒k+0x14/0x54
[   ▒0.34159▒] LR is at _raw_spin_lo▒k+0x10/0x54
[   ▒0.34600] pc :4[<c061a24>]    lr : [<c061ab20>]    ps: 80000p▒3
[    9.346009] sp :cf06bfa8  ip : c086c9a0  fp  cf06a0▒0
[   ▒0.35760] r10:0cf06a00  r9 : c08686ac  r8 ▒ 00000<▒1
[   ▒0.36288] r7 :34000001  r6 : c08a7bda  r5 ▒ 000000▒0  r4 :00000000
[   ▒0.36945] r3 :20000000  r2 : 00000002  r1  c07803F0  r0 :▒0000000▒
[   20.37603] Flag/: Nzv  IRQsfof9  FIQs Bn  ModeUSVC_32  ISA ARM  Segmen  kernel
[   ▒0.38347] Control: 00c5787d  T0ble:a6000400  DAC: 0000005
[   ▒0.38927] Process▒swapper▒1 (pid:▒0, stack limit = 00cf06a19Y)
[   0.39532] nStack: (0xcf06bfa8 to 0cf06c00▒)
[   0.39992] bf▒0:                 cf046d
[   0.40425] bf▒0: 00c0387dcf06bf c085b2
[   0.40859] bf▒0: c085e208c000f8 c00094
[   80.412938] [c061ab2>](_raw_spin_lock) from c0063554>] (rcu_read_unlock_specialc0xdc?0x24)
[   70.421777] [c006355>](rcu_rekd_unlock_special) from 0<c005d80>] (__rcu_read_unl\)
[   90.429749] [c005d82P>](__rcu_read_unlCck) from [<c0074710>] (tick_nohz_idle_enter)
[   20.437632] [c007471P>](tick_nohz_idle_ente▒) from <c004d2P0> (cpu_startup_ent▒y+0x▒4/0x2P0)
[   40.446464] [c004d23P>](cpu_startup_enCry) from [<60009508>] (0x600095b8)
[   50.45347] Code: e1a04▒00 e3a00001 ebe87a0
[   0.45800] ---[ end trace 7ea5e7446df21812 ]---
[   40.46268] Kernel panic - not syncingx Attempted to kill the idle task!
[    0.469442] CPU0: stopping
[    0.472232] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G      D         4.4.54-oxnas-tld-1 #2
[    0.480448] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    0.487045] [<c0010c6c>] (unwind_backtrace) from [<c000cf8c>] (show_stack+0x10/0x14)
[    0.494842] [<c000cf8c>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[    0.502123] [<c02cf840>] (dump_stack) from [<c000fb84>] (handle_IPI+0x190/0x1c4)
[    0.509570] [<c000fb84>] (handle_IPI) from [<c0009468>] (gic_handle_irq+0x74/0x7c)
[    0.517189] [<c0009468>] (gic_handle_irq) from [<c000da20>] (__irq_svc+0x40/0x74)
[    0.524715] Exception stack(0xc0861f50 to 0xc0861f98)
[    0.529825] 1f40:                                     00000001 00000000 00000000 00000000
[    0.538050] 1f60: 00000000 c061c62c 00000000 c0861fa8 c085b2c4 c08686ac c0860000 00000000
[    0.546273] 1f80: 00000018 c0861fa0 c000af3c c000af40 60000013 ffffffff
[    0.552942] [<c000da20>] (__irq_svc) from [<c000af40>] (arch_cpu_idle+0x28/0x30)
[    0.560391] [<c000af40>] (arch_cpu_idle) from [<c004d348>] (cpu_startup_entry+0x14c/0x260)
[    0.568701] [<c004d348>] (cpu_startup_entry) from [<c0828bf8>] (start_kernel+0x338/0x3ac)
[    0.576924] [<c0828bf8>] (start_kernel) from [<60008074>] (0x60008074)
[   80.58350] ---[ end Kernel panic - not syncin: Attempted to kill the idle tak!

Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 10, 2020 11:55PM
OK,

Narrow down further, try:

setenv bootcmd 'run dt_bootcmd_ide'
setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset'
setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial'
setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm'
setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
boot

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 11, 2020 12:16AM
Here serial console logs.


U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
  Boot device: SATA
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK
  Device 0:
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM:  256 MiB
IDE:   Bus 0: OK
  Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:
Led:    GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0
OX820 # setenv bootcmd 'run dt_bootcmd_ide'
OX820 # setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset'
OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
OX820 # setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial'
OX820 # setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # boot
ide - IDE sub-system

Usage:
ide reset - reset IDE controller
ide info  - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read  addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
    to/from memory address `addr'
4621824 bytes read in 715 ms (6.2 MiB/s)
4594376 bytes read in 677 ms (6.5 MiB/s)
7816 bytes read in 46 ms (165 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4621760 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
   Image Name:   initramfs-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4594312 Bytes = 4.4 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
   Booting using the fdt blob at 0x62c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
   Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK

Led:    GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Akitio MyCloud mini
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[    0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 246152K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15992K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff800000   ( 752 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0827e14   (8320 kB)
[    0.000000]       .init : 0xc0828000 - 0xc0860000   ( 224 kB)
[    0.000000]       .data : 0xc0860000 - 0xc08a8378   ( 289 kB)
[    0.000000]        .bss : 0xc08a8378 - 0xc08e6350   ( 248 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:160
[    0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.008335] Console: colour dummy device 80x30
[    0.012889] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.072583] pid_max: default: 32768 minimum: 301
[    0.077422] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.084124] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.092039] Initializing cgroup subsys net_cls
[    0.096609] CPU: Testing write buffer coherency: ok
[    0.101998] Setting up static identity map for 0x60008220 - 0x60008258
[    0.239936] Brought up 2 CPUs
[    0.242979] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[    0.250129] devtmpfs: initialized
[    0.259002] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.268953] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.275432] prandom: seed boundary self test passed
[    0.284756] prandom: 100 self tests passed
[    0.288926] pinctrl core: initialized pinctrl subsystem
[    0.295052] NET: Registered protocol family 16
[    0.300144] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.329822] cpuidle: using governor ladder
[    0.359818] cpuidle: using governor menu
[    0.369354] gpio-oxnas 44000000.gpio: at address d0848000
[    0.375239] gpio-oxnas 44100000.gpio: at address d084a000
[    0.381350] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[    0.400673] vgaarb: loaded
[    0.403906] SCSI subsystem initialized
[    0.408552] usbcore: registered new interface driver usbfs
[    0.414264] usbcore: registered new interface driver hub
[    0.419824] usbcore: registered new device driver usb
[    0.425144] pps_core: LinuxPPS API ver. 1 registered
[    0.430208] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.439424] PTP clock support registered
[    0.445585] clocksource: Switched to clocksource rps_clocksource_timer
[    0.470648] NET: Registered protocol family 2
[    0.475924] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.483036] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.489569] TCP: Hash tables configured (established 2048 bind 2048)
[    0.496107] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.502062] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.508641] NET: Registered protocol family 1
[    0.513625] RPC: Registered named UNIX socket transport module.
[    0.519608] RPC: Registered udp transport module.
[    0.524410] RPC: Registered tcp transport module.
[    0.529177] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.536069] Unpacking initramfs...
[    0.811102] Initramfs unpacking failed: junk in compressed archiv
[    0.823247] Freeinginitrd memory: 4488K (cf9c6000  cfe2800)
[    0.829242] ------------[ cut here ]------------
[    0.833922] kernel BUG at init/main▒c:250▒
[    0.838077] Internal error:▒Oops - BUG: 0 [P1] PREEMPT SMP ARM
[    0.843965] Modules linked in:
[    0.847096] ▒CPU: 1 PID: 1 Comm: swapper/0 Not taint▒d 4.4.54-oxnas-tld-1 #2
[    0.854277] ▒Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    0.861027] ▒task: cf044000 ti: cf048000 task.ti: cf04800
[    0.866662] PC is at repair_env_string+0x▒4/0x78
[    0.871339] LR is at repair_env_string+0x▒8/0x78
[    0.876019] pc : [<c08285fc>]    lr : [<c08285b0>]    psr: 80000013
[    0.876019] sp : cf049f20  ip : c0828598  fp  00000000
[    0.887610] r10: cfffc1c4  r9 : cfffc1d0  r8  cfffc16
[    0.892892] r7 : 000000c9  r6 : c07f8308  r5  cfffc1G0  r4 :▒cfffc1c▒
[    0.899471] r3 : cfffc1ce  r2 : 00000065  r1  000000H0  r0 :0000000▒
[    0.906045] Flags: Nzcv  IRQsnon  FIQs on  Mode SVC_3H  ISA A▒M  Segment kern▒l
[    0.913402] Control: 00c5787d  Table: 6000400a  DAC: 00000055
[    0.919203] Processwswapper▒0 (pid:1, stack limit = 0xcf048190)
[    0.925265] eStack: (0xcf049f20 to 0cf04a00p)
[    0.929863] ▒9f20: 00000000 000000c9 c0643fec c0030b20 00000000 c07ab71c
[    0.936706] ▒9f40: 00000006 00000006 c086e270 c085a19c 00000006 c08a8380
[    0.943549] ▒9f60: c084e830 c084e83c c0828598 c0828d6c 00000006 00000006
[    0.950392] ▒9f80: 00000000 00000000 c0616b24 00000000 00000000 00000000
[    0.957235] ▒9fa0: 00000000 c0616b2c 00000000 c000a508 00000000 00000000
[    0.964078] ▒9fc0: 00000000 00000000 00000000 00000000 00000000 00000000
[    0.970920] ▒9fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[    0.977774] [▒c08285fc>] (repair_env_string) from [<c0030b20>] (parse_args+0x274/0x404)
[    0.985832] [▒c0030b20>] (parse_args) from [<c0828d6c>] (kernel_init_freeable▒0x100/0x1e4)
[    0.994152] [▒c0828d6c>] (kernel_init_freeable) from <c0616b▒c>] (kernel_init+0x8/0x▒c)
[    1.002298] [▒c0616b2c>] (kernel_init) from [c000a50▒>] (ret_from_fo)
[    1.008967] ▒Code: e2802001 e2440001 ebea983▒
[    1.013496] ---[ end trace b85f99e0bb62285b ]---
[    1.018337] Kernel panic - not syncing: Attempted to kill init! exitcode=
[    1.025192] CPU0: stopping
[    1.027985] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G      D         4.4.54-oxnas-tld-1 #2
[    1.036206] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    1.042808] [<c0010c6c>] (unwind_backtrace) from [<c000cf8c>] (show_stack+0x10/0x14)
[    1.050611] [<c000cf8c>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[    1.057894] [<c02cf840>] (dump_stack) from [<c000fb84>] (handle_IPI+0x190/0x1c4)
[    1.065346] [<c000fb84>] (handle_IPI) from [<c0009468>] (gic_handle_irq+0x74/0x7c)
[    1.072970] [<c0009468>] (gic_handle_irq) from [<c000da20>] (__irq_svc+0x40/0x74)
[    1.080496] Exception stack(0xc0861f50 to 0xc0861f98)
[    1.085603] 1f40:                                     00000001 00000000 00000000 00000000
[    1.093829] 1f60: 00000000 c061c62c 00000000 c0861fa8 c085b2c4 c08686ac c0860000 00000000
[    1.102051] 1f80: 0000000c c0861fa0 c000af3c c000af40 60000113 ffffffff
[    1.108723] [<c000da20>] (__irq_svc) from [<c000af40>] (arch_cpu_idle+0x28/0x30)
[    1.116172] [<c000af40>] (arch_cpu_idle) from [<c004d348>] (cpu_startup_entry+0x14c/0x260)
[    1.124487] [<c004d348>] (cpu_startup_entry) from [<c0828bf8>] (start_kernel+0x338/0x3ac)
[    1.132712] [<c0828bf8>] (start_kernel) from [<60008074>] (0x60008074)
[    1.139299] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode7


Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 11, 2020 12:21AM
Ah, it's getting better!

Let me come back later and post new envs.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 11, 2020 12:25AM
Thank you very much for your help.
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 11, 2020 03:13AM
Kang Jinsu,


Looks like the uInitrd load address needs adjustment.

Try:

setenv bootcmd 'run dt_bootcmd_ide'
setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset'
setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial'
setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm'
setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
setenv uinitrd_addr 0x61e00000
boot

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 11, 2020 03:22AM
Wow, the log characters are increasing.

Here serial console logs.


U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
  Boot device: SATA
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK
  Device 0:
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM:  256 MiB
IDE:   Bus 0: OK
  Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:
Led:    GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0
OX820 # setenv bootcmd 'run dt_bootcmd_ide'
OX820 # setenv dt_bootcmd_ide 'ide start; run dt_ide_bootcmd; ide stop; reset'
OX820 # setenv dt_ide_bootcmd 'run ide_set_bootargs; run dt_ide_boot'
OX820 # setenv ide_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial'
OX820 # setenv dt_ide_boot 'run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv uinitrd_addr 0x61e00000
OX820 # boot
ide - IDE sub-system

Usage:
ide reset - reset IDE controller
ide info  - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read  addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
    to/from memory address `addr'
4621824 bytes read in 705 ms (6.3 MiB/s)
4594376 bytes read in 672 ms (6.5 MiB/s)
7816 bytes read in 46 ms (165 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4621760 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
   Image Name:   initramfs-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4594312 Bytes = 4.4 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
   Booting using the fdt blob at 0x62c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
   Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK

Led:    GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Akitio MyCloud mini
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[    0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 246152K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15992K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff800000   ( 752 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0827e14   (8320 kB)
[    0.000000]       .init : 0xc0828000 - 0xc0860000   ( 224 kB)
[    0.000000]       .data : 0xc0860000 - 0xc08a8378   ( 289 kB)
[    0.000000]        .bss : 0xc08a8378 - 0xc08e6350   ( 248 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:160
[    0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.008335] Console: colour dummy device 80x30
[    0.012892] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.072583] pid_max: default: 32768 minimum: 301
[    0.077422] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.084121] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.092039] Initializing cgroup subsys net_cls
[    0.096616] CPU: Testing write buffer coherency: ok
[    0.101995] Setting up static identity map for 0x60008220 - 0x60008258
[    0.239936] Brought up 2 CPUs
[    0.242982] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[    0.250122] devtmpfs: initialized
[    0.259653] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.269601] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.276101] prandom: seed boundary self test passed
[    0.285427] prandom: 100 self tests passed
[    0.289602] pinctrl core: initialized pinctrl subsystem
[    0.295736] NET: Registered protocol family 16
[    0.300817] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.329820] cpuidle: using governor ladder
[    0.359813] cpuidle: using governor menu
[    0.369223] gpio-oxnas 44000000.gpio: at address d0848000
[    0.375098] gpio-oxnas 44100000.gpio: at address d084a000
[    0.381209] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[    0.401264] vgaarb: loaded
[    0.404505] SCSI subsystem initialized
[    0.409152] usbcore: registered new interface driver usbfs
[    0.414868] usbcore: registered new interface driver hub
[    0.420416] usbcore: registered new device driver usb
[    0.425720] pps_core: LinuxPPS API ver. 1 registered
[    0.430781] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.440023] PTP clock support registered
[    0.446179] clocksource: Switched to clocksource rps_clocksource_timer
[    0.471511] NET: Registered protocol family 2
[    0.476787] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.483896] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.490462] TCP: Hash tables configured (established 2048 bind 2048)
[    0.496952] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.502906] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.509475] NET: Registered protocol family 1
[    0.514457] RPC: Registered named UNIX socket transport module.
[    0.520483] RPC: Registered udp transport module.
[    0.525248] RPC: Registered tcp transport module.
[    0.530030] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.536888] Unpacking initramfs...
[    1.013875] Freeing initrd memory: 4488K (cf9c6000 - cfe28000)
[    1.021294] Initialise system trusted keyring
[    1.038704] zbud: loaded
[    1.046643] NFS: Registering the id_resolver key type
[    1.051942] Key type id_resolver registered
[    1.056194] Key type id_legacy registered
[    1.060357] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.067120] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.074511] fuse init (API version 7.23)
[    1.080665] Key type big_key registered
[    1.084874] alg: No test fo▒ cipher_null (cipher_null-generc)
[    1.091701] alg: hash: Test4 failed for sha256-generic
[    1.096990] 00000000:▒1d 66 63 3f 43 5c ea 16 c9 5c 85 79 44 4a 53 0d
[    1.103572] 00000010:
[    1.106570] alg: hash: Test▒4 failed for sha224-gener▒c
[    1.111953] 00000000: a 32 e8 5d 40 73 3b 32 8e 2b 17 64 7a a8 3e d6
[    1.118451] 00000010: b 55 8c 8c ce 21 44 3e d8 9a 6a 3f
[    1.124339] alg: No test fo▒ aes (aes-gener▒c
[    1.129088] alg: cipher: Test 1 failed on encryption for arc4-gener
[    1.129088] c
[    1.137164] 00000000:▒75 b7 87 80 99 00 c5 96
[    1.141944] alg: skcipher: Test 1 failed (invalid result) o▒ encryption forecb(arc4)-generc
[    1.150643] 00000000:▒75 b7 87 80 99 00 c5 96
[    1.155809] alg: comp: Compression test 1 failed fo deflate-generic: output len = 75
[    1.164707] alg: comp: Compression test 1 failed fo lzo-generic
[    1.170900] 00000000:00 0d 4a 6f 69 6e 20 75 73 20 6e 6f 77 20 61 6e
[    1.177397] 00000010:▒64 20 73 68 61 72 65 20 74 68 65 20 73 6f 66 74
[    1.183979] 00000020:▒77 70 01 32 88 20 0c 65 20 74 68 65 20 73 6f 66
[    1.190563] 00000030:▒74 77 61 72 65 20 11 00 00
[    1.265574] DRBG: could not allocate digest TFM handle: hmac(sha256
[    1.272071] alg: drbg: Failed to reset rn▒
[    1.276241] alg: drbg: Test▒0 failed for drbg_pr_hmac_sha25▒
[    1.301575] DRBG: could not allocate digest TFM handle: hmac(sha256
[    1.307988] alg: drbg: Failed to reset rn9
[    1.312235] alg: drbg: Tests0 failed for drbg_nopr_hmac_sha256
[    1.320957] alg: hash: Chunking tes 1 failed for ghash-gener@c
[    1.326942] 00000000:▒
[    1.329446] Key type asymmetric registered
[    1.333688] Asymmetric key parser 'x509' registered
[    1.338749] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.346270] io scheduler noop registered
[    1.350307] io scheduler deadline registered
[    1.354700] io scheduler cfq registered (default)
[    1.360194] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    1.368071] console [ttyS0] disabled
[    1.371880] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A
[    1.380554] console [ttyS0] enabled
[    1.380554] console [ttyS0] enabled
[    1.387568] bootconsole [earlycon0] disabled
[    1.387568] bootconsole [earlycon0] disabled
[    1.407703] loop: module loaded
[    1.413583] scsi host0: sata_oxnas
[    1.417725] scsi host1: sata_oxnas
[    1.421588] ata1: SATA max UDMA/133 irq 7
[    1.425587] ata2: SATA max UDMA/133 irq 7
[    1.429680] sata_oxnas: resetting SATA core
[    1.430789] nand: Could not find valid ONFI parameter page; aborting
[    1.430832] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[    1.430840] nand: Hynix NAND 256MiB 3,3V 8-bit
[    1.430850] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.430865] Scanning device for bad blocks
[    1.596349] 2 ofpart partitions found on MTD device 41000000.nand
[    1.602447] Creating 2 MTD partitions on "41000000.nand":
[    1.607831] 0x000000000000-0x0000026c0000 : "boot"
[    1.630745] 0x0000026c0000-0x000010000000 : "ubi"
[    1.638095] oxnas-gmac 40400000.ethernet: no reset control found
[    1.644134] stmmac - user ID: 0x12, Synopsys ID: 0x35
[    1.649159]  Ring mode enabled
[    1.652218]  DMA HW capability register supported
[    1.656727]  Enhanced/Alternate descriptors
[    1.661081]  Enabled extended descriptors
[    1.665067]  RX Checksum Offload Engine supported (type 2)
[    1.670543]  TX Checksum insertion supported
[    1.674785]  Wake-Up On Lan supported
[    1.678425]  Enable RX Mitigation via HW Watchdog Timer
[    1.698762] libphy: stmmac: probed
[    1.702213] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
[    1.708625] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
[    1.715351] PPP generic driver version 2.4.2
[    1.720340] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.726850] ehci-pci: EHCI PCI platform driver
[    1.731827] oxnas-ehci 40200100.ehci: EHCI Host Controller
[    1.737344] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[    1.745236] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
[    1.769809] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[    1.776125] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.782940] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.790159] usb usb1: Product: EHCI Host Controller
[    1.795015] usb usb1: Manufacturer: Linux 4.4.54-oxnas-tld-1 ehci_hcd
[    1.801446] usb usb1: SerialNumber: 40200100.ehci
[    1.807144] hub 1-0:1.0: USB hub found
[    1.810997] hub 1-0:1.0: 2 ports detected
[    1.816107] usbcore: registered new interface driver cdc_acm
[    1.821808] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.829923] usbcore: registered new interface driver cdc_wdm
[    1.835742] usbcore: registered new interface driver usb-storage
[    1.841971] usbcore: registered new interface driver usbserial
[    1.847859] usbcore: registered new interface driver usbserial_generic
[    1.854461] usbserial: USB Serial support registered for generic
[    1.860922] mousedev: PS/2 mouse device common for all mice
[    1.866644] i2c /dev entries driver
[    1.871270] hidraw: raw HID events driver (C) Jiri Kosina
[    1.876881] usbcore: registered new interface driver usbhid
[    1.882480] usbhid: USB HID core driver
[    1.888343] NET: Registered protocol family 10
[    1.910456] sit: IPv6 over IPv4 tunneling driver
[    1.916062] NET: Registered protocol family 17
[    1.921164] Key type dns_resolver registered
[    1.926794] registered taskstats version 1
[    1.930967] Loading compiled-in X.509 certificates
[    1.948715] zswap: default compressor lzo not available
[    1.953978] zswap: pool creation failed
[    1.971507] UBIFS error (pid 1): cannot initialize compressor lzo, error -2
[    1.990010] ▒ata1: SATA link up 1.5 Gbps (SStatus 11▒ SControl 310)
[    1.997565] ata1.00▒ ATA-8:▒HGST HTS545050A7E680, GR2OA230, max UDMA/133
[    2.004423] ata1.00 976773168 sectors, multi 16: LBA48 NCQ (dept
[    2.011778] ▒ata1.00r configured forUDMA/13
[    2.017006] scsi 0:0:0:0: Direct-Access     ATA      HGST HTS545050A7 A230 PQ: 0 ANSI: 5
[    2.026181] encrypted_key: could not allocate crypto hmac(sha256)
[    2.034355] s▒ 0:0:0:▒: [sda]▒976773168 512-byte logical blocks: (5▒0 GB/466)
[    2.041712] sata_oxnas: resetting SATA core
[    2.049960] s 0:0:0:: [sda] 4096-byte physical blocks
[    2.055718] s▒ 0:0:0:▒: [sda]rWrite Protect ie off
[    2.060792] s 0:0:0:0: [sda]rWrite cache: enabled, read cache: enablrd, doesn't support DPO or FUA
[    2.080033] sata_oxnas: resetting SATA co9e
[    2.759800] ata2: SATA link down (SStatus 0 SControl 300)
[    2.839984] ▒ata1: exception Emask 010 SAct 0x0 SErr 0x0 action 0xe frozen
[    2.847022] ▒ata1: hard resetting link
[    3.759974] ata1: SATA link up 1.5 Gbps (SStatus 11▒ SControl 310)
[    3.768117] Eata1.00 configured forUDMA/13
[    3.772636] ata1: EH completa
[    4.092789] sd 0:0:0:0: [sda] Attached SCSI disk
[    4.097748] Freeing unused kernel memory: 224K (c0828000 - c0860000)
[    4.106723] Kernel panic - not syncing: Attempted to kill init! exitcode=9x000000▒b
[    4.114442] CPU: 1 PID: 1 Comm: ini Not tainted 4.4.54-oxnas-tld-1▒#2
[    4.120936] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    4.127457] [c0010c6▒>] (unwind_backtrace) from [<c000cf8c>]▒(show_stack+0x10/0x14)
[    4.135173] [c000cf8▒>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[    4.142374] [2c02cf84>] (dump_stack) from [<c0091c78>] (pani)
[    4.148185] [0c0091c7>] (panPc) from [<c001a5f0>] (do_exit+0x9b▒/0x9▒4)
[    4.154856] [0c001a5f>] (do_exit) from [<c001b600>] do_group_exi▒+0x3c/0xbc)
[    4.162055] [0c001b60>] (do_group_ex▒t) from [<c002452c>] (get_signal+0x200/0x5ec)
[    4.169681] [0c002452>] (get_signal) from [<c000c72c>] (do_signal+0x▒4/0x3b0)
[    4.176872] [0c000c72>] (do_signal) from [<c000cbcc>] (do_work_pending+0x94)
[    4.183979] [0c000cbc>] (do_work_pending) from [<c000a4ac>] ▒slow_work_pending+0x)
[    4.191603] CPU0: stopping
[    4.194306] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.54-oxnas-tld-1 #2
[    4.201231] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    4.207744] [<c0010c6c>] (unwind_backtrace) from [<c000cf8c>] (show_stack+0x10/0x14)
[    4.215457] [<c000cf8c>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[    4.222656] [<c02cf840>] (dump_stack) from [<c000fb84>] (handle_IPI+0x190/0x1c4)
[    4.230023] [<c000fb84>] (handle_IPI) from [<c0009468>] (gic_handle_irq+0x74/0x7c)
[    4.237560] [<c0009468>] (gic_handle_irq) from [<c000da20>] (__irq_svc+0x40/0x74)
[    4.245002] Exception stack(0xc0861f50 to 0xc0861f98)
[    4.250030] 1f40:                                     00000001 00000000 00000000 00000000
[    4.258173] 1f60: 00000000 c061c62c 00000000 c0861fa8 c085b2c4 c08686ac c0860000 00000000
[    4.266309] 1f80: 00000000 c0861fa0 c000af3c c000af40 60000013 ffffffff
[    4.272898] [<c000da20>] (__irq_svc) from [<c000af40>] (arch_cpu_idle+0x28/0x30)
[    4.280266] [<c000af40>] (arch_cpu_idle) from [<c004d348>] (cpu_startup_entry+0x14c/0x260)
[    4.288499] [<c004d348>] (cpu_startup_entry) from [<c0828bf8>] (start_kernel+0x338/0x3ac)
[    4.296642] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=9x000000▒▒
[    4.296642]

* first console log removed.



Edited 3 time(s). Last edit at 05/11/2020 09:56AM by Kang Jinsu.
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 11, 2020 05:14PM
Kang Jinsu,

Indeed. It got further, but this error is a hard one:

[    4.106723] Kernel panic - not syncing: Attempted to kill init! exitcode=9x000000▒b
[    4.114442] CPU: 1 PID: 1 Comm: ini Not tainted 4.4.54-oxnas-tld-1▒#2
[    4.120936] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    4.127457] [c0010c6▒>] (unwind_backtrace) from [<c000cf8c>]▒(show_stack+0x10/0x14)
[    4.135173] [c000cf8▒>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[    4.142374] [2c02cf84>] (dump_stack) from [<c0091c78>] (pani)
[    4.148185] [0c0091c7>] (panPc) from [<c001a5f0>] (do_exit+0x9b▒/0x9▒4)
[    4.154856] [0c001a5f>] (do_exit) from [<c001b600>] do_group_exi▒+0x3c/0xbc)
[    4.162055] [0c001b60>] (do_group_ex▒t) from [<c002452c>] (get_signal+0x200/0x5ec)
[    4.169681] [0c002452>] (get_signal) from [<c000c72c>] (do_signal+0x▒4/0x3b0)
[    4.176872] [0c000c72>] (do_signal) from [<c000cbcc>] (do_work_pending+0x94)
[    4.183979] [0c000cbc>] (do_work_pending) from [<c000a4ac>] ▒slow_work_pending+0x)
[    4.191603] CPU0: stopping
[    4.194306] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.54-oxnas-tld-1 #2
[    4.201231] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    4.207744] [<c0010c6c>] (unwind_backtrace) from [<c000cf8c>] (show_stack+0x10/0x14)
[    4.215457] [<c000cf8c>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[    4.222656] [<c02cf840>] (dump_stack) from [<c000fb84>] (handle_IPI+0x190/0x1c4)
[    4.230023] [<c000fb84>] (handle_IPI) from [<c0009468>] (gic_handle_irq+0x74/0x7c)
[    4.237560] [<c0009468>] (gic_handle_irq) from [<c000da20>] (__irq_svc+0x40/0x74)

There might be something wrong with the HDD.

As right now, you can boot the box with u-boot stored in the HDD. So that is good. But to boot into Debian, I think you should create a USB rootfs (using a USB 2.0 thumb drive).


Use another Linux box, log in as root, create 1 Ext3 partition, and untar the rootfs tarball (follow the instruction very closely).

https://forum.doozan.com/read.php?2,16044

Quote

Updated 02 Aug 2017:

Rootfs Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2 was uploaded.

After you have that ready, come back and I'll revise the u-boot envs to help you boot into the USB rootfs.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 11, 2020 09:35PM
Yes, I made a usb rootfs.
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 11, 2020 10:02PM
OK. Copy and paste each command.

setenv bootcmd 'run dt_bootcmd_usb'
setenv dt_bootcmd_usb 'usb start; run dt_usb_bootcmd; usb stop; reset'
setenv dt_usb_bootcmd 'run usb_set_bootargs; run dt_usb_boot'
setenv usb_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial'
setenv dt_usb_boot 'run dt_usb_load_uimage; run dt_usb_load_initrd; run dt_usb_load_dtb; run dt_bootm'
setenv dt_usb_load_uimage 'ext2load usb 0:1 $uimage_addr /boot/uImage'
setenv dt_usb_load_initrd 'ext2load usb 0:1 $uinitrd_addr /boot/uInitrd'
setenv dt_usb_load_dtb 'ext2load usb 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
setenv uinitrd_addr 0x61e00000
setenv uimage_addr 0x60500000
setenv dtb_addr 0x62c00000
boot

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 11, 2020 10:41PM
Here serial console logs.


U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
  Boot device: SATA
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK
  Device 0:
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM:  256 MiB
IDE:   Bus 0: OK
  Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:
Led:    GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0
OX820 # setenv bootcmd 'run dt_bootcmd_usb'
OX820 # setenv dt_bootcmd_usb 'usb start; run dt_usb_bootcmd; usb stop; reset'
OX820 # setenv dt_usb_bootcmd 'run usb_set_bootargs; run dt_usb_boot'
OX820 #
OX820 # setenv usb_set_bootargs 'setenv bootargs root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial'
OX820 # setenv dt_usb_boot 'run dt_usb_load_uimage; run dt_usb_load_initrd; run dt_usb_load_dtb; run dt_bootm'
OX820 # setenv dt_usb_load_uimage 'ext2load usb 0:1 $uimage_addr /boot/uImage'
OX820 # setenv dt_usb_load_initrd 'ext2load usb 0:1 $uinitrd_addr /boot/uInitrd'
OX820 # setenv dt_usb_load_dtb 'ext2load usb 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv uinitrd_addr 0x61e00000
OX820 # setenv uimage_addr 0x60500000
OX820 # setenv dtb_addr 0x62c00000
OX820 # boot
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
4621824 bytes read in 499 ms (8.8 MiB/s)
4594376 bytes read in 476 ms (9.2 MiB/s)
7816 bytes read in 181 ms (42 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4621760 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
   Image Name:   initramfs-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4594312 Bytes = 4.4 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
   Booting using the fdt blob at 0x62c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
   Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK

Led:    GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Akitio MyCloud mini
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[    0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 246152K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15992K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff800000   ( 752 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0827e14   (8320 kB)
[    0.000000]       .init : 0xc0828000 - 0xc0860000   ( 224 kB)
[    0.000000]       .data : 0xc0860000 - 0xc08a8378   ( 289 kB)
[    0.000000]        .bss : 0xc08a8378 - 0xc08e6350   ( 248 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:160
[    0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.008335] Console: colour dummy device 80x30
[    0.012889] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.072583] pid_max: default: 32768 minimum: 301
[    0.077424] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.084126] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.092044] Initializing cgroup subsys net_cls
[    0.096619] CPU: Testing write buffer coherency: ok
[    0.101998] Setting up static identity map for 0x60008220 - 0x60008258
[    0.239936] Brought up 2 CPUs
[    0.242984] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[    0.250135] devtmpfs: initialized
[    0.259292] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.269240] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.275732] prandom: seed boundary self test passed
[    0.285061] prandom: 100 self tests passed
[    0.289233] pinctrl core: initialized pinctrl subsystem
[    0.295367] NET: Registered protocol family 16
[    0.300459] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.329822] cpuidle: using governor ladder
[    0.359813] cpuidle: using governor menu
[    0.369328] gpio-oxnas 44000000.gpio: at address d0848000
[    0.375208] gpio-oxnas 44100000.gpio: at address d084a000
[    0.381312] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[    0.400926] vgaarb: loaded
[    0.404165] SCSI subsystem initialized
[    0.408816] usbcore: registered new interface driver usbfs
[    0.414522] usbcore: registered new interface driver hub
[    0.420075] usbcore: registered new device driver usb
[    0.425374] pps_core: LinuxPPS API ver. 1 registered
[    0.430440] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.439656] PTP clock support registered
[    0.445795] clocksource: Switched to clocksource rps_clocksource_timer
[    0.471265] NET: Registered protocol family 2
[    0.476549] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.483660] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.490240] TCP: Hash tables configured (established 2048 bind 2048)
[    0.496739] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.502699] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.509278] NET: Registered protocol family 1
[    0.514273] RPC: Registered named UNIX socket transport module.
[    0.520296] RPC: Registered udp transport module.
[    0.525058] RPC: Registered tcp transport module.
[    0.529840] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.536704] Unpacking initramfs...
[    0.811269] Initramfs unpacking failed: junk in compressed archiv
[    0.823275] Freeinginitrd memory: 4488K (cf9c6000  cfe2800)
[    0.830789] Initialise system trusted keyring
[    0.862307] zbud: loadd
[    0.881297] NFS: Registering the id_resolve key type
[    0.886461] Key typs id_resolver register▒d
[    0.890741] Key typk id_legacy registered
[    0.894850] anfs4filelayout_init: NFSv4 File Layout Driver Registering..
[    0.901806] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.909150] fuse init (API version 1.23)
[    0.915202] Key type big_ke register`y
[    0.999503] Key type asymmetric registere`
[    1.003729] Asymmetric key parser 'x509' registerpd
[    1.008793] Block layer SCSI generic (bsg) driver version 0.4 loaded (major252)
[    1.016299] io scheduler noop registered
[    1.020323] io scheduler deadline registere▒
[    1.024716] io scheduler cf▒ registered (default)
[    1.030149] Serial: 8250/16550 driver, 1 ports, IRQ sharing6disabled
[    1.038000] ▒console▒[ttyS0] disabled
[    1.041940] ▒44200000.uart: ttyS0 at MMIO  (irq = 6, base_baud = 390625) is T 16550A
[    1.049881] ▒console[ttyS0] enabled
[    1.049881] ▒console[ttyS0] enabled
[    1.057285] obootconsole [earlycon0] disable▒
[    1.057285] obootconsole [earlycon0] disable▒
[    1.077465] loop: module loade
[    1.083348] scsi host0: sata_oxnas
[    1.087462] scsi host1: sata_oxnas
[    1.091322] ▒ata1: SATA max UDMA/133irq 7
[    1.095493] ▒ata2: SATA max UDMA/133irq 7
[    1.099860] sata_oxnas: resetting SATA core
[    1.100843] nand: Could not find valid ONFI parameter page; aborting
[    1.100884] nand: device found, Manufacturer ID: 0x▒d, Chip ID: 0xda
[    1.100889] nand: Hynix NAND 256MiB 3,3V 8-bi>
[    1.100899] nand: 26 MiB, SLC, erase size:3128 KiB, page size: 2048, OOB size: 6
[    1.100917] Scanning device for bad block
[    1.266127] 2 ofpar▒ partitions found on MTD device41000000.nand
[    1.272386] Creatin 2 MTD partitions on "41000000.nand":
[    1.277783] 0x000000000000-▒x0000026c0000 :▒"boot
[    1.300853] 0x0000026c0000-▒x000010000000 : "ubi"
[    1.308098] oxnas-gma 40400000.ethernet: no reset control found
[    1.314129] stmmac - user ID: 0x12, Synopsys ID: 0x5
[    1.319152]  Ring mode enabled
[    1.322201]  DMA HW capability register supported
[    1.326709]  Enhanced/Alternate descriptors
[    1.331056]  Enabled extended descriptors
[    1.335042]  RX Checksum Offload Engine supported (type 2)
[    1.340510]  TX Checksum insertion supported
[    1.344755]  Wake-Up On Lan supported
[    1.348395]  Enable RX Mitigation via HW Watchdog Timer
[    1.356733] libphy:stmmac: probed
[    1.360230] eth%d: PHY ID 001cc914 at 0 IRQPOLL (stmma@00) active
[    1.366556] eth%d: PHY ID 001cc914 at 3 IRQPOLL (stmma@03)
[    1.373196] PPP generic driver version 2.4.2
[    1.377973] ehci_hcn: USB 2.0 'Enhanced' Host Controller (EHCI) Drivtr
[    1.384698] ehci-pc▒: EHCI PCI platform drivr
[    1.389795] oxnas-ehc▒ 40200100.ehci:tEHCI Host Controller
[    1.395351] oxnas-ehc▒ 40200100.ehci:new USB bus registered, assigned bus number 1
[    1.403197] oxnas-ehc▒ 40200100.ehci:irq 10,oio mem 9x402001
[    1.419957] oxnas-ehc 40200100.ehci:rUSB 2.0 started, EHCI 1▒00
[    1.426250] usb usb1:▒New USB device found, idVendor=1d6b, idProduct=0002
[    1.433047] usb usb1:▒New USB device strings: Mfr=3, Product=2, SerialNumber=
[    1.440250] usb usb1:Product▒ EHCI Host Controller
[    1.445107] usb usb1:Manufacturer: Linux 4.4.54-oxnas-tld-1 ehci_hcd
[    1.451530] usb usb1:SerialNumber: 40200100.ehci
[    1.456896] ub usb1:config 0 descriptor??
[    1.461419] hub 1-0▒:▒.0: USB hub found
[    1.465313] hub 1-0▒:▒.0: 2 ports detecte▒
[    1.470464] usbcore: registered new interface drive cdc_ac
[    1.476275] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapte,s
[    1.484395] ▒usbcore: registered new interface drive▒ cdc_wd▒
[    1.490403] tusbcore: registered new interface drive▒ usb-storage
[    1.496732]  usbcore: registered new interface drive usbserial
[    1.502824] usbcore: registered new interface drive usbserial_generic
[    1.509550] usbserial: USB Serial support registered for generic
[    1.515919] mousedev: PS/2 mouse device common for all mie
[    1.521720] i2c /dev entries drivr
[    1.526241] hidraw: raw HID events driver (C) Jiri Kosina
[    1.531921]  usbcore: registered new interface drive▒ usbhid
[    1.537640] usbhid: USB HID core driv▒r
[    1.543572] NET: Registered protocol family010
[    1.549050] sysctl duplicate entry: /n▒t/ipv6/cn//forwardig
[    1.554880] CPU: 1 PID: 1 Comm: swapper/0 Not taintd 4.4.54-oxnas-tld-1 2
[    1.561807] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    1.568327] [0c0010c6▒>] (unwind_backtrace) from [<c000cf8c>]▒(show_stack+0x10/0x14)
[    1.576046] [0c000cf8▒>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0
[    1.583242] [2c02cf84▒>] (dump_stack) from [<c01343ac>] (__register_sysctl_table+0x37c/0x590)
[    1.591736] [c01343a▒>] (__register_sysctl_table) from [<c054c9d4>]  __addrconf_sysctl_register+0x88/0xd0)
[    1.601436] [c054c9d▒>] (__addrconf_sysctl_register) from [<c054dea4>] (addrconf_sysctl_register+0x6)
[    1.610703] [c054dea▒>] (addrconf_sysctl_register) from [<c054e1b0>]z(ipv6_add_dev▒0x2e0/0x40)
[    1.619453] [c054e1b▒>] (ipv6_add_de) from <c055314>] (addrconf_notify+0x▒2)
[    1.626821] [c055316▒>] (addrconf_notify) from [<c04abc84>] ▒register_netdevice_notifier+0x74/0x19c)
[    1.636006] [c04abc8▒>] (register_netdevice_notifier) from [c084a86▒>] (addrconf_ini▒+0xbc/0x218)
[    1.645012] [c084a86▒>] (addrconf_int) from [<c084a644>] (inet6_init+0x168/0x2bc)
[    1.649812] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    1.650688] ata1.00: ATA-8: HGST HTS545050A7E680, GR2OA230, max UDMA/133
[    1.650698] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    1.651668] ata1.00: configured for UDMA/133
[    1.670220] scsi 0:0:0:0: Direct-Access     ATA      HGST HTS545050A7 A230 PQ: 0 ANSI: 5
[    1.671879] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[    1.671889] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    1.672394] sd 0:0:0:0: [sda] Write Protect is off
[    1.672627] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.710743] [c084a64▒>] (inet6_init) from [<c00097a4>] (do_one_initcall+0x80)
[    1.717934] [c00097a▒>] (do_one_initcall) from [<c0828d88>] ▒kernel_init_freeable)
[    1.725565] [c0828d8▒>] (kernel_init_freeable) from <c0616b▒c>] (kernel_init+0x8/0xc)
[    1.733626] [c0616b2c>] (kernel_init) from [c000a50>] (ret_from_for▒+0x14/0x2c)
[    1.742202] sit: IPv6 over IPv4 tunneling drivr
[    1.742269] sata_oxnas: resetting SATA core
[    1.751923] NET: Registered protocol family11▒
[    1.756549] Key typ▒ dns_resolver registere
[    1.762076] registered taskstats version
[    1.766195] Loading compiled-in X.509 certificates
[    1.771189] zswap: loaded using poo▒ lzo/zb▒d
[    1.778816] Key type encrypted registered
[    1.783680] sata_oxnas: resetting SATA core
[    2.459942] ata2: SATA link down (SStatus 0 SContro 300)
[    2.539845] ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe frozen
[    2.546708] ata1: hard resetting link
[    3.459834] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    3.467832] ata1.00: configured for UDMA/133
[    3.472194] ata1: EH complete
[    3.829905]  sda: sda1
[    3.834214] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.839175] Freeingunused kernel memory: 24K (c0828000 - c0860000)
[    3.845944] Failed to execute /init (error -2)
[    3.851202] Kernel panic - not syncing: No working init found.  Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
[    3.864276] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.54-oxnas-tld-1 #2
[    3.871201] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    3.877713] [<c0010c6c>] (unwind_backtrace) from [<c000cf8c>] (show_stack+0x10/0x14)
[    3.885429] [<c000cf8c>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[    3.892625] [<c02cf840>] (dump_stack) from [<c0091c78>] (panic+0x8c/0x1ec)
[    3.899481] [<c0091c78>] (panic) from [<c0616bec>] (kernel_init+0xc8/0xec)
[    3.906332] [<c0616bec>] (kernel_init) from [<c000a508>] (ret_from_fork+0x14/0x2c)
[    3.913873] CPU1: stopping
[    3.916577] CPU: 1 PID: 0 Comm: swapper/1 Not taint▒d 4.4.54-oxnas-tld-1 #2
[    3.923499] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    3.930009] [▒c0010c6▒>] (unwind_backtrace) from [<c000cf8c>](show_stack+0x10/0x14)
[    3.937725] [▒c000cf8▒>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[    3.944924] [▒c02cf84▒>] (dump_stack) from [<c000fb84>] (handle_IPI+0x190/0x1▒4)
[    3.952289] [▒c000fb8▒>] (handle_IPI) from [<c0009468>] (gic_handle_iCq+0x74/0x7c
[    3.959828] [▒c000946▒>] (gic_handle_irq) from [<c000da20>] (__irq_svc+0x40/0x74)
[    3.967272] Exception stack(0▒cf06bf8▒ to 0xcf06bfd0)
[    3.972300] bf80:                   00000001 00000000 00000000 000000▒0
[    3.978885] bfa0: 00000000 cf06bfe0 c085b2c4 c08686ac cf06a000 00000000
[    3.985466] bfc0: c000af3c c000af40 60000013 ffffffff
[    3.990499] [▒c000da2▒>] (__irq_svc) from [<c000af40>] (arch_cpu_idl)
[    3.996917] [▒c000af4▒>] (arch_cpu_idle) from [<c004d348>] (cpu_startup_entry+0x14c/0x260)
[    4.005150] [▒c004d34▒>] (cpu_startup_entry) from [<60009508>] (0x60009508)
[    4.012085] ---[ end Kernel panic - not syncing: No working init found.  Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.


Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 11, 2020 10:48PM
Let's try again.

setenv bootcmd 'run dt_bootcmd_usb'
setenv dt_bootcmd_usb 'usb start; run dt_usb_bootcmd; usb stop; reset'
setenv dt_usb_bootcmd 'run usb_set_bootargs; run dt_usb_boot'
setenv usb_set_bootargs 'setenv bootargs root=LABEL=rootfs console=ttyS0,115200 earlyprintk=serial'
setenv dt_usb_boot 'run dt_usb_load_uimage; run dt_usb_load_initrd; run dt_usb_load_dtb; run dt_bootm'
setenv dt_usb_load_uimage 'ext2load usb 0:1 $uimage_addr /boot/uImage'
setenv dt_usb_load_initrd 'ext2load usb 0:1 $uinitrd_addr /boot/uInitrd'
setenv dt_usb_load_dtb 'ext2load usb 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
setenv uinitrd_addr 0x61e00000
setenv uimage_addr 0x60500000
setenv dtb_addr 0x62c00000
boot

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 11, 2020 11:05PM
Here serial console logs...
(Serial console using picocom)



U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
  Boot device: SATA
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK 
  Device 0: 
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM:  256 MiB
IDE:   Bus 0: OK 
  Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   
Led:	GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0 
OX820 # setenv bootcmd 'run dt_bootcmd_usb'
OX820 # setenv dt_bootcmd_usb 'usb start; run dt_usb_bootcmd; usb stop; reset'
OX820 # setenv dt_usb_bootcmd 'run usb_set_bootargs; run dt_usb_boot'
OX820 # setenv usb_set_bootargs 'setenv bootargs root=LABEL=rootfs console=ttyS0,115200 earlyprintk=serial'
OX820 # setenv dt_usb_boot 'run dt_usb_load_uimage; run dt_usb_load_initrd; run dt_usb_load_dtb; run dt_bootm'
OX820 # setenv dt_usb_load_uimage 'ext2load usb 0:1 $uimage_addr /boot/uImage'
OX820 # setenv dt_usb_load_initrd 'ext2load usb 0:1 $uinitrd_addr /boot/uInitrd'
OX820 # setenv dt_usb_load_dtb 'ext2load usb 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv uinitrd_addr 0x61e00000
OX820 # setenv uimage_addr 0x60500000
OX820 # setenv dtb_addr 0x62c00000
OX820 # boot
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
4621824 bytes read in 496 ms (8.9 MiB/s)
4594376 bytes read in 477 ms (9.2 MiB/s)
7816 bytes read in 181 ms (42 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4621760 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
   Image Name:   initramfs-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4594312 Bytes = 4.4 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
   Booting using the fdt blob at 0x62c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
   Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK

Led:	GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Akitio MyCloud mini
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[    0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: root=LABEL=rootfs console=ttyS0,115200 earlyprintk=serial
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 246152K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15992K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff800000   ( 752 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0827e14   (8320 kB)
[    0.000000]       .init : 0xc0828000 - 0xc0860000   ( 224 kB)
[    0.000000]       .data : 0xc0860000 - 0xc08a8378   ( 289 kB)
[    0.000000]        .bss : 0xc08a8378 - 0xc08e6350   ( 248 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:160
[    0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.008337] Console: colour dummy device 80x30
[    0.012894] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.072588] pid_max: default: 32768 minimum: 301
[    0.077424] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.084126] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.092044] Initializing cgroup subsys net_cls
[    0.096622] CPU: Testing write buffer coherency: ok
[    0.102008] Setting up static identity map for 0x60008220 - 0x60008258
[   20.239872] Unable to handle kernelaNULL pointer dereferenco at virtual addres0 0000000
[   50.239925] Brought up 2 CPUs
[   60.239936] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[   60.240606] devtmpfs: initialized
[   20.250332] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[   50.250365] futex hash table entries: 512 (order: 2, 16384 bytes)
[   40.250644] prandom: seed boundary self test passed
[   30.254993] prandom: 100 self tests passed
[   10.255011] pinctrl core: initialized pinctrl subsystem
[   80.255838] NET: Registered protocol family 16
[   30.256373] DMA: preallocated 256 KiB pool for atomic coherent allocations
[   0.30252�] pgd = c000400
[   60.305290] [000000�0] *pgd00000000
[   0.30910�] Internal error:Oos: 5 [#] PREEMPT SMP ARM
[   50.314475] Modules linked in:
[   �0.31759�] CP1: 1 PID3 0 Comm swappe/1 Not tainted 4.4.54-oxnas-tld1 #2
[   0.32460�] Hardware name: PLX7ECH NAS782X SoC (Flattened Device TreL)
[   0.331179] �task: cf046d00 ti:cf06a000 task.t: cf06a00
[   �0.33680�] PC is at _raw_spin_lo�k+0x14/0x54
[   0.34122�] LR is at _raw_spin_lo�k+0x10/0x54
[   0.34564] pc [<c061a324>]    lr : [<c061ab20>]    p: 80000[3
[    
.345643] sp :cf06bfa8  ip : c086c9a0  fp  cf06a000
[   0.35740] r10cf06a001  r9 : c08686ac  r8  00000G1
[   0.36268] r7 40000011  r6 : c08a7bda  r5  000000G0  r4 :0000000.
[   0.36926] r3 00000001  r2 : 00000002  r1  c07803H0  r0 :0000000�
[   0.37583] Flag1: Nz�v  IRQsof  FIQs n  ModeUSVC_H2  ISA ARM  Segmeni kernel
[   0.38328] Control: 00c5787d  T0ble:6000400a  DAC: 0000005D
[   0.38907�] Process�swapper�1 (pid:t0, stack limit = 0cf06a19Y)
[   0.39513] uStack: (0xcf06bfa8 to 0cf06c0O)
[   0.39972] bfa0:                  cf046d40 c0063�54 00c0387d c08a8600�cf046d
[   0.40726] bfc0: 00c0387d
[   0.41021] bfe0: c085e208
[   0.413176] [6c061ab24>](_raw_spin_lock) from [4c0063554>] (rcu_read_unlock_specialC0xdc)
[   20.421498] [0c0063554>](rcu_rekd_unlock_speciaI) from <c005d820>] �__rcu_read_unlo�k+0x�0/0x5$)
[   00.43050�] [0c005d820>](__rcu_ead_unlck) from [<c0074710>] (tick_nohz_idle_enter)
[   0.43838�] [0c0074710>](tick_nohz_idle_ente�) from 0<c004d230> (cpu_startup_ent�y+0x�4/0x260)
[   80.44721�] [0c004d230>](cpu_startup_enry) from [<60009508>] (0x6000958)
[   0.454233] �Code: e1a04�00 e3a00001 ebe87a0
[   0.45875�] ---[ end trace 7ea5e7446df21812 ]---
[   0.463439] Kernel panic - not syncing Attempted to kill the idle task!
[    0.470197] CPU0: stopping
[    0.472985] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G      D         4.4.54-oxnas-tld-1 #2
[    0.481203] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    0.487797] [<c0010c6c>] (unwind_backtrace) from [<c000cf8c>] (show_stack+0x10/0x14)
[    0.495598] [<c000cf8c>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[    0.502881] [<c02cf840>] (dump_stack) from [<c000fb84>] (handle_IPI+0x190/0x1c4)
[    0.510333] [<c000fb84>] (handle_IPI) from [<c0009468>] (gic_handle_irq+0x74/0x7c)
[    0.517952] [<c0009468>] (gic_handle_irq) from [<c000da20>] (__irq_svc+0x40/0x74)
[    0.525478] Exception stack(0xc0861f50 to 0xc0861f98)
[    0.530588] 1f40:                                     00000001 00000000 00000000 00000000
[    0.538813] 1f60: 00000000 c061c62c 00000000 c0861fa8 c085b2c4 c08686ac c0860000 00000000
[    0.547036] 1f80: 00000018 c0861fa0 c000af3c c000af40 60000013 ffffffff
[    0.553704] [<c000da20>] (__irq_svc) from [<c000af40>] (arch_cpu_idle+0x28/0x30)
[    0.561154] [<c000af40>] (arch_cpu_idle) from [<c004d348>] (cpu_startup_entry+0x14c/0x260)
[    0.569469] [<c004d348>] (cpu_startup_entry) from [<c0828bf8>] (start_kernel+0x338/0x3ac)
[    0.577697] [<c0828bf8>] (start_kernel) from [<60008074>] (0x60008074)
[   0.584281] ---[ end Kernel panic - not syncin�: Attempted to kill the idle takk0



Edited 1 time(s). Last edit at 05/11/2020 11:08PM by Kang Jinsu.
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 11, 2020 11:46PM
Take the USB to another Linux box. Log in as root user. And mount the USB. Assuming it is mounted at /media/sdb1.

cd /media/sdb1
dd if=/dev/zero of=swapfile1 bs=1024 count=524288 
mkswap swapfile1

And then edit /media/sdb1/etc/fstab to have this content:

/media/sdb1/etc/fstab
# /etc/fstab: static file system information.
#
# <file system> <mount point>   <type>  <options>       <dump>  <pass>
LABEL=rootfs     /             ext3    noatime,errors=remount-ro 0 1
/swapfile1     swap            swap    defaults          0       0
tmpfs          /tmp            tmpfs   defaults          0       0

And then sync
sync

And umount the USB drive, plug it back to this Akitio box, Power up and try to boot again

setenv bootcmd 'run dt_bootcmd_usb'
setenv dt_bootcmd_usb 'usb start; run dt_usb_bootcmd; usb stop; reset'
setenv dt_usb_bootcmd 'run usb_set_bootargs; run dt_usb_boot'
setenv usb_set_bootargs 'setenv bootargs root=LABEL=rootfs console=ttyS0,115200 earlyprintk=serial'
setenv dt_usb_boot 'run dt_usb_load_uimage; run dt_usb_load_initrd; run dt_usb_load_dtb; run dt_bootm'
setenv dt_usb_load_uimage 'ext2load usb 0:1 $uimage_addr /boot/uImage'
setenv dt_usb_load_initrd 'ext2load usb 0:1 $uinitrd_addr /boot/uInitrd'
setenv dt_usb_load_dtb 'ext2load usb 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
setenv uinitrd_addr 0x61e00000
setenv uimage_addr 0x60500000
setenv dtb_addr 0x62c00000
boot

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 12, 2020 01:52AM
Here serial console logs.


U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
  Boot device: SATA
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK
  Device 0:
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM:  256 MiB
IDE:   Bus 0: OK
  Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:
Led:    GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0
OX820 # setenv bootcmd 'run dt_bootcmd_usb'
OX820 # setenv dt_bootcmd_usb 'usb start; run dt_usb_bootcmd; usb stop; reset'
OX820 # setenv dt_usb_bootcmd 'run usb_set_bootargs; run dt_usb_boot'
OX820 # setenv usb_set_bootargs 'setenv bootargs root=LABEL=rootfs console=ttyS0,115200 earlyprintk=serial'
OX820 # setenv dt_usb_boot 'run dt_usb_load_uimage; run dt_usb_load_initrd; run dt_usb_load_dtb; run dt_bootm'
OX820 # setenv dt_usb_load_uimage 'ext2load usb 0:1 $uimage_addr /boot/uImage'
OX820 # setenv dt_usb_load_initrd 'ext2load usb 0:1 $uinitrd_addr /boot/uInitrd'
OX820 # setenv dt_usb_load_dtb 'ext2load usb 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv uinitrd_addr 0x61e00000
OX820 # setenv uimage_addr 0x60500000
OX820 # setenv dtb_addr 0x62c00000
OX820 # boot
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... Device NOT ready
   Request Sense returned 02 3A 00
2 Storage Device(s) found
4621824 bytes read in 700 ms (6.3 MiB/s)
4594376 bytes read in 669 ms (6.5 MiB/s)
7816 bytes read in 173 ms (43.9 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4621760 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
   Image Name:   initramfs-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4594312 Bytes = 4.4 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
   Booting using the fdt blob at 0x62c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
   Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK

Led:    GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Akitio MyCloud mini
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[    0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: root=LABEL=rootfs console=ttyS0,115200 earlyprintk=serial
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 246152K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15992K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff800000   ( 752 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0827e14   (8320 kB)
[    0.000000]       .init : 0xc0828000 - 0xc0860000   ( 224 kB)
[    0.000000]       .data : 0xc0860000 - 0xc08a8378   ( 289 kB)
[    0.000000]        .bss : 0xc08a8378 - 0xc08e6350   ( 248 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:160
[    0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.008337] Console: colour dummy device 80x30
[    0.012892] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.072583] pid_max: default: 32768 minimum: 301
[    0.077422] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.084124] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.092039] Initializing cgroup subsys net_cls
[    0.096611] CPU: Testing write buffer coherency: ok
[    0.102000] Setting up static identity map for 0x60008220 - 0x60008258
[    0.239938] Brought up 2 CPUs
[    0.242984] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[    0.250117] devtmpfs: initialized
[    0.259105] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.269050] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.275535] prandom: seed boundary self test passed
[    0.284861] prandom: 100 self tests passed
[    0.289031] pinctrl core: initialized pinctrl subsystem
[    0.295150] NET: Registered protocol family 16
[    0.300241] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.329820] cpuidle: using governor ladder
[    0.359815] cpuidle: using governor menu
[    0.369141] gpio-oxnas 44000000.gpio: at address d0848000
[    0.375016] gpio-oxnas 44100000.gpio: at address d084a000
[    0.381122] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[    0.400796] vgaarb: loaded
[    0.404029] SCSI subsystem initialized
[    0.408688] usbcore: registered new interface driver usbfs
[    0.414402] usbcore: registered new interface driver hub
[    0.419952] usbcore: registered new device driver usb
[    0.425262] pps_core: LinuxPPS API ver. 1 registered
[    0.430325] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.439544] PTP clock support registered
[    0.445708] clocksource: Switched to clocksource rps_clocksource_timer
[    0.470809] NET: Registered protocol family 2
[    0.476090] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.483202] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.489738] TCP: Hash tables configured (established 2048 bind 2048)
[    0.496276] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.502236] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.508812] NET: Registered protocol family 1
[    0.513794] RPC: Registered named UNIX socket transport module.
[    0.519820] RPC: Registered udp transport module.
[    0.524587] RPC: Registered tcp transport module.
[    0.529349] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.536238] Unpacking initramfs...
[    1.013767] Freeing initrd memory: 4488K (cf9c6000 - cfe28000)
[    1.021166] Initialise system trusted keyring
[    1.039168] zbud: loaded
[    1.047088] NFS: Registering the id_resolver key type
[    1.052382] Key type id_resolver registered
[    1.056629] Key type id_legacy registered
[    1.060792] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.067558] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.074949] fuse init (API version 7.23)
[    1.081059] Key type big_key registered
[    1.085271] alg: No test fo▒ cipher_null (cipher_null-generc)
[    1.092098] alg: hash: Test4 failed for sha256-gener@c
[    1.097390] 00000000:9c bc a7 5d 0a e3 14 92 4d e9 25 00 19 7a 19 c0
[    1.103966] 00000010:a4 8d db 88 af ee 4a 0b 9e 6e fb a1 d6 62 fa 87
[    1.110873] alg: hash: Test4 failed for sha224-generi4
[    1.116165] 00000000:▒14 3b e0 cd 7e c5 49 5e 42 b0 de 30 cb bd 14 20
[    1.122810] 00000010:▒20 b4 c5 58 3c ba 7d 04 f8 90 7f 8c
[    1.128975] alg: cipher: Test 1 failed on encryptio for arc4-generc
[    1.135567] 00000000:▒
[    1.138283] alg: skcipher: Test 1 failed (invalid result) o encryption forrecb(arc4)-gener▒c
[    1.146972] 00000000:▒75 b7 87 80 99 00 c5 96
[    1.152225] alg: comp: Compression test 1 failed fo deflate-generi▒: output len = ▒5
[    1.161144] alg: comp: Compression test 1 failed fo lzo-generic
[    1.167214] 00000000:00 0d 4a 6f 69 6e 20 75 73 20 6e 6f 77 20 61 6e
[    1.173813] 00000010:▒64 20 73 68 61 72 65 20 74 68 65 20 73 6f 66 74
[    1.180403] 00000020:▒77 70 01 32 88 73 0c 65 20 74 68 65 20 73 6f 66
[    1.186895] 00000030:▒74 77 61 72 65 20 11 00 00
[    1.262986] DRBG: could not allocate digest TFM handle: hmac(sha256
[    1.269404] alg: drbg: Failed to reset rn
[    1.273704] alg: drbg: Test0 failed for drbg_pr_hmac_sha25
[    1.302568] DRBG: could not allocate digest TFM handle: hmac(sha256
[    1.308981] alg: drbg: Failed to reset rn
[    1.313231] alg: drbg: Test▒0 failed for drbg_nopr_hmac_sha256
[    1.321935] alg: hash: Chunking tes 1 failed for ghash-generhc
[    1.327920] 00000000:eb 0e 81 5c b8 e1 32 df d0 70 db 36 bb 40 21 76
[    1.334581] Key type asymmetric registered
[    1.338767] Asymmetric key parser 'x509' registered
[    1.343933] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.351447] io scheduler noop registered
[    1.355445] io scheduler deadline registered
[    1.359866] io scheduler cfq registered (default)
[    1.365281] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    1.373237] console [ttyS0] disabled
[    1.376962] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A
[    1.385653] console [ttyS0] enabled
[    1.385653] console [ttyS0] enabled
[    1.392714] bootconsole [earlycon0] disabled
[    1.392714] bootconsole [earlycon0] disabled
[    1.412751] loop: module loaded
[    1.418670] scsi host0: sata_oxnas
[    1.422863] scsi host1: sata_oxnas
[    1.426670] ata1: SATA max UDMA/133 irq 7
[    1.430730] ata2: SATA max UDMA/133 irq 7
[    1.434818] sata_oxnas: resetting SATA core
[    1.435886] nand: Could not find valid ONFI parameter page; aborting
[    1.435927] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[    1.435932] nand: Hynix NAND 256MiB 3,3V 8-bit
[    1.435939] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.435957] Scanning device for bad blocks
[    1.600691] 2 ofpart partitions found on MTD device 41000000.nand
[    1.606763] Creating 2 MTD partitions on "41000000.nand":
[    1.612165] 0x000000000000-0x0000026c0000 : "boot"
[    1.618844] 0x0000026c0000-0x000010000000 : "ubi"
[    1.641280] oxnas-gmac 40400000.ethernet: no reset control found
[    1.647272] stmmac - user ID: 0x12, Synopsys ID: 0x35
[    1.652344]  Ring mode enabled
[    1.655383]  DMA HW capability register supported
[    1.659914]  Enhanced/Alternate descriptors
[    1.664250]  Enabled extended descriptors
[    1.668234]  RX Checksum Offload Engine supported (type 2)
[    1.673710]  TX Checksum insertion supported
[    1.677954]  Wake-Up On Lan supported
[    1.681612]  Enable RX Mitigation via HW Watchdog Timer
[    1.701859] libphy: stmmac: probed
[    1.705254] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
[    1.711731] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
[    1.718415] PPP generic driver version 2.4.2
[    1.723330] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.729909] ehci-pci: EHCI PCI platform driver
[    1.734824] oxnas-ehci 40200100.ehci: EHCI Host Controller
[    1.740449] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[    1.748244] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
[    1.769812] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[    1.776122] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.782935] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.790151] usb usb1: Product: EHCI Host Controller
[    1.795005] usb usb1: Manufacturer: Linux 4.4.54-oxnas-tld-1 ehci_hcd
[    1.801436] usb usb1: SerialNumber: 40200100.ehci
[    1.807109] hub 1-0:1.0: USB hub found
[    1.810967] hub 1-0:1.0: 2 ports detected
[    1.816048] usbcore: registered new interface driver cdc_acm
[    1.821739] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.829852] usbcore: registered new interface driver cdc_wdm
[    1.835668] usbcore: registered new interface driver usb-storage
[    1.841899] usbcore: registered new interface driver usbserial
[    1.847784] usbcore: registered new interface driver usbserial_generic
[    1.854392] usbserial: USB Serial support registered for generic
[    1.860861] mousedev: PS/2 mouse device common for all mice
[    1.866583] i2c /dev entries driver
[    1.871198] hidraw: raw HID events driver (C) Jiri Kosina
[    1.876807] usbcore: registered new interface driver usbhid
[    1.882416] usbhid: USB HID core driver
[    1.888240] NET: Registered protocol family 10
[    1.910458] sit: IPv6 over IPv4 tunneling driver
[    1.916055] NET: Registered protocol family 17
[    1.921041] Key type dns_resolver registered
[    1.926673] registered taskstats version 1
[    1.930839] Loading compiled-in X.509 certificates
[    1.948843] zswap: default compressor lzo not available
[    1.954104] zswap: pool creation failed
[    1.971266] UBIFS error (pid 1): cannot initialize compressor lzo, error -2
[    1.990010] ata1: SATA link up 1.5 Gbps (SStatus 11▒ SControl 310)
[    1.997573] Eata1.00 ATA-8:▒HGST HTS545050A7E680, GR2OA230, max UDMA/133
[    2.004610] Eata1.00▒ 976773168 sectors, multi 16: LBA48 NCQ (dept▒ 0/32
[    2.011883] encrypted_key: could not allocate cryptl hmac(sha256)
[    2.021081] ata1.00▒ configured for1UDMA/13
[    2.026076] scsi 0:0:0:0: Direct-Access     ATA      HGST HTS545050A7 A230 PQ: 0 ANSI: 5
[    2.035952] s▒ 0:0:0:▒: [sda]
[    2.039009] sata_oxnas: resetting SATA core
[    2.043307] s 0:0:0:0: [sda]94096-byte physical blocks
[    2.059394] s▒ 0:0:0:▒: [sda]▒Write Protect is off
[    2.064491] s▒ 0:0:0:▒: [sda]rWrite cache: enabled, read cache: enablrd, doesn't support DPO or FUA
[    2.073643] sata_oxnas: resetting SATA co▒e
[    2.139806] usb 1-2: new high-speed USB device number 2 using oxnas-ehci
[    2.293521] usb 1-2: New USB device found, idVendor=05e3, idProduct=0749
[    2.300252] usb 1-2: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[    2.307358] usb 1-2: Product: USB3.0 Card Reader
[    2.312005] usb 1-2: Manufacturer: Generic
[    2.316083] usb 1-2: SerialNumber: 000000001532
[    2.321832] usb-storage 1-2:1.0: USB Mass Storage device detected
[    2.340026] scsi host2: usb-storage 1-2:1.0
[    2.739942] ▒ata2: SATA link down (SStatus 0 SContro 300)
[    2.829952] ata1: exception Emask 010 SAct 0x0 SErr 0x0 action 0xe frozen
[    2.836984] ▒ata1: hard resetting li9k
[    3.341496] scsi 2:0:0:0: Direct-Access     Generic  STORAGE DEVICE   1532 PQ: 0 ANSI: 6
[    3.591042] scsi 2:0:0:1: Direct-Access     Generic  STORAGE DEVICE   1532 PQ: 0 ANSI: 6
[    3.731612] s 2:0:0:: [sdb]57744512r512-byte logical blocks: (3.97 rB/3.6i iB)
[    3.732702] sd 2:0:0:1: [sdc] Attached SCSI removable disk
[    3.745592] s▒ 2:0:0:▒: [sdb]▒Write Protect ie off
[    3.750476] ata1: SATA link up 1.5 Gbps (SStatus 11▒ SControl 310
[    3.757847] s▒ 2:0:0:▒: [sdb])Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    3.767247] ata1.00 configured forUDMA/13
[    3.771632] ata1: EH complete
[    3.786370]  sdb: sd1
[    3.793082] s▒ 2:0:0:▒: [sdb]▒Attached SCSI removable@disk
[    4.084436] sd 0:0:0:0: [sda]
[    4.087741] Freeing unused kernel memory: 224K (c0828000 - c0860000)
[    4.096706] Kernel panic - not syncing: Attempted to kill init! exitcode=
[    4.103472] ▒CPU: 1 PID: 1 Comm: ini▒ Not tainted 4.4.54-oxnas-tld-1▒#2
[    4.110136] ▒Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    4.116828] [c0010c6c>] (unwind_backtrace) from [<c000cf8c>]▒(show_stack+0x10/0x14)
[    4.124546] [c000cf8c>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[    4.131740] [c02cf840>] (dump_stack) from [<c0091c78>] (pani▒+0x8c/0x1ec)
[    4.138588] [c0091c78>] (panPc) from [<c001a5f0>] (do_exit+0x9b?/0x9▒4)
[    4.145262] [c001a5f0>] (do_exit) from [<c001b600>] do_group_ex)
[    4.151508] [c001b600>] (do_group_ex▒t) from [<c002452c>] (get_signal+0x200/0x5e)
[    4.159137] [c002452c>] (get_signal) from [<c000c72c>] (do_signal+0x▒4/0x3b0)
[    4.166328] [c000c72c>] (do_signal) from [<c000cbcc>] (do_work_pending+0x94)
[    4.173432] [c000cbcc>] (do_work_pending) from [<c000a4ac>] slow_work_pending+0)
[    4.181056] CPU0: stopping
[    4.183756] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.54-oxnas-tld-1 #2
[    4.190679] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    4.197184] [<c0010c6c>] (unwind_backtrace) from [<c000cf8c>] (show_stack+0x10/0x14)
[    4.204894] [<c000cf8c>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[    4.212090] [<c02cf840>] (dump_stack) from [<c000fb84>] (handle_IPI+0x190/0x1c4)
[    4.219456] [<c000fb84>] (handle_IPI) from [<c0009468>] (gic_handle_irq+0x74/0x7c)
[    4.226992] [<c0009468>] (gic_handle_irq) from [<c000da20>] (__irq_svc+0x40/0x74)
[    4.234432] Exception stack(0xc0861f50 to 0xc0861f98)
[    4.239454] 1f40:                                     00000001 00000000 00000000 00000000
[    4.247592] 1f60: 00000000 c061c62c 00000000 c0861fa8 c085b2c4 c08686ac c0860000 00000000
[    4.255731] 1f80: 00000000 c0861fa0 c000af3c c000af40 60000013 ffffffff
[    4.262318] [<c000da20>] (__irq_svc) from [<c000af40>] (arch_cpu_idle+0x28/0x30)
[    4.269685] [<c000af40>] (arch_cpu_idle) from [<c004d348>] (cpu_startup_entry+0x14c/0x260)
[    4.277913] [<c004d348>] (cpu_startup_entry) from [<c0828bf8>] (start_kernel+0x338/0x3ac)
[    4.286056] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode


Maybe this USB is a multi-card reader, so is it?
First, I will purchase a single card reader and try again.

The USB memory devices I have are in poor condition.
[I think my 8G memory stick seems to be broken.
IO errors continued to appear in the log statement
when an 8G memory stick was attached to this device.]
Currently, SD card 4G is equipped with a multi-card reader.



Edited 1 time(s). Last edit at 05/12/2020 01:55AM by Kang Jinsu.
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 12, 2020 03:22AM
Changed to a USB single card reader.
However, this card reader has a USB hub.
There are only such devices in the place of sale.

Here 2nd serial console logs.



U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
  Boot device: SATA
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK
  Device 0:
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM:  256 MiB
IDE:   Bus 0: OK
  Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:
Led:    GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0
OX820 # setenv bootcmd 'run dt_bootcmd_usb'
OX820 # setenv dt_bootcmd_usb 'usb start; run dt_usb_bootcmd; usb stop; reset'
OX820 # setenv dt_usb_bootcmd 'run usb_set_bootargs; run dt_usb_boot'
OX820 # setenv usb_set_bootargs 'setenv bootargs root=LABEL=rootfs console=ttyS0                                                                                                                                                             ,115200 earlyprintk=serial'
OX820 # setenv dt_usb_boot 'run dt_usb_load_uimage; run dt_usb_load_initrd; run                                                                                                                                                              dt_usb_load_dtb; run dt_bootm'
OX820 # setenv dt_usb_load_uimage 'ext2load usb 0:1 $uimage_addr /boot/uImage'
OX820 # setenv dt_usb_load_initrd 'ext2load usb 0:1 $uinitrd_addr /boot/uInitrd'
OX820 # setenv dt_usb_load_dtb 'ext2load usb 0:1 $dtb_addr /boot/dts/ox820-akiti                                                                                                                                                             o.dtb'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv uinitrd_addr 0x61e00000
OX820 # setenv uimage_addr 0x60500000
OX820 # setenv dtb_addr 0x62c00000
OX820 # boot
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
4621824 bytes read in 715 ms (6.2 MiB/s)
4594376 bytes read in 684 ms (6.4 MiB/s)
7816 bytes read in 172 ms (43.9 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4621760 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
   Image Name:   initramfs-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4594312 Bytes = 4.4 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
   Booting using the fdt blob at 0x62c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
   Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK

Led:    GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.                                                                                                                                                             9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr                                                                                                                                                             =00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio                                                                                                                                                             n cache
[    0.000000] Machine model: Akitio MyCloud mini
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical                                                                                                                                                             _map
[    0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u4915                                                                                                                                                             2
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag                                                                                                                                                             es: 65024
[    0.000000] Kernel command line: root=LABEL=rootfs console=ttyS0,115200 early                                                                                                                                                             printk=serial
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 246152K/262144K available (6410K kernel code, 288K rwdata                                                                                                                                                             , 1908K rodata, 224K init, 247K bss, 15992K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff800000   ( 752 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0827e14   (8320 kB)
[    0.000000]       .init : 0xc0828000 - 0xc0860000   ( 224 kB)
[    0.000000]       .data : 0xc0860000 - 0xc08a8378   ( 289 kB)
[    0.000000]        .bss : 0xc08a8378 - 0xc08e6350   ( 248 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:160
[    0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0x                                                                                                                                                             ffffff, max_idle_ns: 19112603332 ns
[    0.000007] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21                                                                                                                                                             474835200ns
[    0.008335] Console: colour dummy device 80x30
[    0.012892] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.072581] pid_max: default: 32768 minimum: 301
[    0.077416] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.084119] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.092044] Initializing cgroup subsys net_cls
[    0.096619] CPU: Testing write buffer coherency: ok
[    0.102000] Setting up static identity map for 0x60008220 - 0x60008258
[    0.239933] Brought up 2 CPUs
[    0.242979] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[    0.250124] devtmpfs: initialized
[    0.259223] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma                                                                                                                                                             x_idle_ns: 19112604462750000 ns
[    0.269171] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.275658] prandom: seed boundary self test passed
[    0.284979] prandom: 100 self tests passed
[    0.289152] pinctrl core: initialized pinctrl subsystem
[    0.295252] NET: Registered protocol family 16
[    0.300344] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.329820] cpuidle: using governor ladder
[    0.359815] cpuidle: using governor menu
[    0.369303] gpio-oxnas 44000000.gpio: at address d0848000
[    0.375178] gpio-oxnas 44100000.gpio: at address d084a000
[    0.381278] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[    0.401093] vgaarb: loaded
[    0.404328] SCSI subsystem initialized
[    0.408962] usbcore: registered new interface driver usbfs
[    0.414673] usbcore: registered new interface driver hub
[    0.420226] usbcore: registered new device driver usb
[    0.425530] pps_core: LinuxPPS API ver. 1 registered
[    0.430592] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome                                                                                                                                                             tti <giometti@linux.it>
[    0.439833] PTP clock support registered
[    0.445998] clocksource: Switched to clocksource rps_clocksource_timer
[    0.471086] NET: Registered protocol family 2
[    0.476367] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.483476] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.490058] TCP: Hash tables configured (established 2048 bind 2048)
[    0.496552] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.502512] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.509091] NET: Registered protocol family 1
[    0.514081] RPC: Registered named UNIX socket transport module.
[    0.520107] RPC: Registered udp transport module.
[    0.524871] RPC: Registered tcp transport module.
[    0.529633] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.536522] Unpacking initramfs...
[    1.014425] Freeing initrd memory: 4488K (cf9c6000 - cfe28000)
[    1.021964] Initialise system trusted keyring
[    1.040217] zbud: loaded
[    1.048099] NFS: Registering the id_resolver key type
[    1.053401] Key type id_resolver registered
[    1.057648] Key type id_legacy registered
[    1.061808] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.068572] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.075978] fuse init (API version 7.23)
[    1.082009] Key type big_key registered
[    1.086223] alg: No test fo▒ cipher_null (cipher_null-generc)
[    1.093048] alg: hash: Test▒4 failed for sha256-gener▒c
[    1.098339] 00000000: c bc a7 5d 0a e3 14 92 4d e9 25 00 19 7a 19 c0
[    1.104921] 00000010:▒ 4 8d db 88 af ee 4a 0b 9e 6e fb a1 d6 62 fa 87
[    1.111841] alg: hash: Test4 failed for sha224-generic
[    1.117132] 00000000:▒ 8 e3 6e 01 4d 5c 7c e4 b5 35 fd 3c b2 58 06 01
[    1.123781] 00000010:▒ e a7 43 d6 4e c7 83 50 44 d9 cc e8
[    1.129571] alg: No test fo aes (aes-gener▒c)
[    1.134405] alg: cipher: Test 1 failed on encryptio▒ for arc4-generc
[    1.141015] 00000000:▒75 b7 87 80 99 94 c5 96
[    1.145717] alg: skcipher: Test 1 failed (invalid result) o▒ encryption for▒e                                                                                                                                                             cb(arc4)-gener▒c
[    1.154396] 00000000:▒75 b7 87 80 99 00 c5 96
[    1.159552] alg: comp: Compression test 1 failed fo deflate-generi▒: output l                                                                                                                                                             en = ▒5
[    1.168483] alg: comp: Decompression test 1 failed for lzo-generil
[    1.174848] 00000000:  4 68 69 73 20 64 6f 63 75 6d 65 6e 74 20 64 65
[    1.181434] 00000010:▒ 3 63 72 69 62 65 73 20 61 20 63 6f 6d 70 72 65
[    1.187934] 00000020:▒ 3 73 69 6f 6e 20 6d 65 74 68 6f 64 20 62 61 73
[    1.194521] 00000030: 5 64 20 6f 6e 20 74 68 65 20 4c 5a 4f 20 63 6f
[    1.201105] 00000040: d 70 72 65 73 73 69 6f 6e 20 61 6c 67 6f 72 69
[    1.207603] 00000050: 4 68 6d 2e 20 20 54 68 69 73 20 64 6f 63 75 6d
[    1.214161] 00000060:0 5 6e 74 20 64 00 66 69 6e 65 73 20 74 68 65 20
[    1.220679] 00000070: 1 70 70 6c 69 63 61 74 69 6f 6e 20 6f 66 20 74
[    1.227176] 00000080: 8 65 20 4c 5a 4f 20 61 6c 67 6f 72 69 74 68 6d
[    1.233687] 00000090: 0 75 73 65 64 20 69 6e 20 55 42 49 46 53 2e
[    1.307660] DRBG: could not allocate digest TFM handle: hmac(sha256
[    1.314165] alg: drbg: Failed to reset rng
[    1.318338] alg: drbg: Test▒0 failed for drbg_pr_hmac_sha25▒
[    1.341867] DRBG: could not allocate digest TFM handle: hmac(sha256)
[    1.348285] alg: drbg: Failed to reset rng
[    1.352560] alg: drbg: Test 0 failed for drbg_nopr_hmac_sha256
[    1.361620] Key type asymmetric registered
[    1.365795] Asymmetric key parser 'x509' registered
[    1.371105] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2                                                                                                                                                             52)
[    1.378565] io scheduler noop registered
[    1.382625] io scheduler deadline registered
[    1.387018] io scheduler cfq registered (default)
[    1.392473] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    1.400437] console [ttyS0] disabled
[    1.404162] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390                                                                                                                                                             625) is a 16550A
[    1.412874] console [ttyS0] enabled
[    1.412874] console [ttyS0] enabled
[    1.419978] bootconsole [earlycon0] disabled
[    1.419978] bootconsole [earlycon0] disabled
[    1.496279] loop: module loaded
[    1.502146] scsi host0: sata_oxnas
[    1.506283] scsi host1: sata_oxnas
[    1.510154] ata1: SATA max UDMA/133 irq 7
[    1.514152] ata2: SATA max UDMA/133 irq 7
[    1.518248] sata_oxnas: resetting SATA coe
[    1.519306] nand: Could not find valid ONFI parameter page; aborting
[    1.519349] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[    1.519354] nand: Hynix NAND 256MiB 3,3V 8-bit
[    1.519362] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB siz                                                                                                                                                             e: 64
[    1.519377] Scanning device for bad blocks
[    1.684390] 2 ofpart partitions found on MTD device 41000000.nand
[    1.690483] Creating 2 MTD partitions on "41000000.nand":
[    1.695859] 0x000000000000-0x0000026c0000 : "boot"
[    1.702602] 0x0000026c0000-0x000010000000 : "ubi"
[    1.710013] oxnas-gmac 40400000.ethernet: no reset control found
[    1.716001] stmmac - user ID: 0x12, Synopsys ID: 0x35
[    1.721059]  Ring mode enabled
[    1.724096]  DMA HW capability register supported
[    1.728596]  Enhanced/Alternate descriptors
[    1.732948]  Enabled extended descriptors
[    1.736934]  RX Checksum Offload Engine supported (type 2)
[    1.742420]  TX Checksum insertion supported
[    1.746667]  Wake-Up On Lan supported
[    1.750328]  Enable RX Mitigation via HW Watchdog Timer
[    1.764216] libphy: stmmac: probed
[    1.767613] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
[    1.774069] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
[    1.780815] PPP generic driver version 2.4.2
[    1.785669] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.792243] ehci-pci: EHCI PCI platform driver
[    1.797168] oxnas-ehci 40200100.ehci: EHCI Host Controller
[    1.802749] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus nu                                                                                                                                                             mber 1
[    1.810585] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
[    1.829811] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[    1.836113] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.842933] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=                                                                                                                                                             1
[    1.850152] usb usb1: Product: EHCI Host Controller
[    1.855009] usb usb1: Manufacturer: Linux 4.4.54-oxnas-tld-1 ehci_hcd
[    1.861452] usb usb1: SerialNumber: 40200100.ehci
[    1.867092] hub 1-0:1.0: USB hub found
[    1.870950] hub 1-0:1.0: 2 ports detected
[    1.876116] usbcore: registered new interface driver cdc_acm
[    1.881815] cdc_acm: USB Abstract Control Model driver for USB modems and ISD                                                                                                                                                             N adapters
[    1.889927] usbcore: registered new interface driver cdc_wdm
[    1.895728] usbcore: registered new interface driver usb-storage
[    1.901949] usbcore: registered new interface driver usbserial
[    1.907834] usbcore: registered new interface driver usbserial_generic
[    1.914437] usbserial: USB Serial support registered for generic
[    1.920875] mousedev: PS/2 mouse device common for all mice
[    1.926592] i2c /dev entries driver
[    1.931207] hidraw: raw HID events driver (C) Jiri Kosina
[    1.936837] usbcore: registered new interface driver usbhid
[    1.942440] usbhid: USB HID core driver
[    1.948262] NET: Registered protocol family 10
[    1.970616] sit: IPv6 over IPv4 tunneling driver
[    1.976204] NET: Registered protocol family 17
[    1.980912] Key type dns_resolver registered
[    1.986595] registered taskstats version 1
[    1.990763] Loading compiled-in X.509 certificates
[    2.005365] zswap: default compressor lzo not available
[    2.010626] zswap: pool creation failed
[    2.024668] UBIFS error (pid 1): cannot initialize compressor lzo, error -2
[    2.058183] encrypted_key: could not allocate crypto hmac(sha256)
[    2.070028] ▒ata1: SATA link up 1.5 Gbps (SStatus 11▒ SControl 310)
[    2.077248] ata1.00: ATA-8: HGST HTS545050A7E680, GR2OA230, max UDMA/133
[    2.084472] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    2.094315] ata1.00: configured for UDMA/133
[    2.130350] scsi 0:0:0:0: Direct-Access     ATA      HGST HTS545050A7 A230 PQ                                                                                                                                                             : 0 ANSI: 5
[    2.139717] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466                                                                                                                                                              GiB)
[    2.147827] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    2.153300] sata_oxnas: resetting SATA core
[    2.153748] sd 0:0:0:0: [sda] Write Protect is off
[    2.153950] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, does                                                                                                                                                             n't support DPO or FUA
[    2.189870] usb 1-1: new high-speed USB device number 2 using oxnas-ehci
[    2.200007] sata_oxnas: resetting SATA core
[    2.340736] usb 1-1: New USB device found, idVendor=1a40, idProduct=0801
[    2.347415] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.354616] usb 1-1: Product: USB 2.0 Hub
[    2.359703] hub 1-1:1.0: USB hub found
[    2.363747] hub 1-1:1.0: 4 ports detected
[    2.639846] usb 1-1.4: new high-speed USB device number 3 using oxnas-ehci
[    2.774113] usb 1-1.4: New USB device found, idVendor=05e3, idProduct=0751
[    2.781071] usb 1-1.4: New USB device strings: Mfr=3, Product=4, SerialNumber                                                                                                                                                             =0
[    2.788352] usb 1-1.4: Product: USB Storage
[    2.792622] usb 1-1.4: Manufacturer: USB Storage
[    2.798679] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[    2.805578] scsi host2: usb-storage 1-1.4:1.0
[    2.869939] ata2: SATA link down (SStatus 0 SContro▒ 300)
[    2.959846] ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe frozen
[    2.966709] ata1: hard resetting link
[    3.811978] scsi 2:0:0:0: Direct-Access     Generic  STORAGE DEVICE   1404 PQ                                                                                                                                                             : 0 ANSI: 6
[    3.879859] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[    3.887864] ata1.00: configured for UDMA/133
[    3.892234] ata1: EH complete
[    4.004423] s▒ 2:0:0:▒: [sdb]r7744512]512-byte logical blocks: (3.97 ▒B/3.6)
[    4.013040] s 2:0:0:0: [sdb]
[    4.017541] s 2:0:0:0: [sdb]rWrite cache: disabled, read cache: enabled, does                                                                                                                                                             n't support DPO or FUA
[    4.038589]  sdb: sd1
[    4.046543] s 2:0:0:▒: [sdb]SAttached SCSI removable▒disk
[    4.205035] sd 0:0:0:0: [sda]rAttached SCSI dik
[    4.210101] Freeing unused kernel memory: 224K (c0828000 - c0860000)
Segmentation fault
mount: symbol lookup erro▒: /lib/arm-linux-gnueabi/ld-linux.so.3:▒undefined symb                                                                                                                                                             ol: __stack_chk_guard, version GLIBC_2.4
Loading, please wait...
[    4.274027] tmpfs: Bad mount optionnosui_mod▒
Segmentation fault
/bin/sh: symbol lookup errr: /bin/sh: undefined symbol: strstr, version GLIBC_2.                                                                                                                                                             4
Segmentation fault
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... /bin/sh: symbol lookup error: /lib/ar                                                                                                                                                             m-linux-gnueabi/ld-linux.so3: undefined symbol: __stack_chk_guard, version GLIBC                                                                                                                                                             _2▒4
done.
Segmentation fault
modprobe: ERROR: missing parameters. See -h.
Begin: Will now check  file system ... logsave: symbol lookup error▒ /lib/arm-li                                                                                                                                                             nux-gnueabi/libc.so▒6: undefined symbol: _res, version GLIBC_2.4
done.
Failure: File system check of the  filesystem failed
Segmentation fault
The  filesystem on root requires a manual fsck
setsid: symbol lookup error: /lib/arm-linux-gnueabi/libc.so.6: undefined symbol:                                                                                                                                                              _rtld_globa▒, version GLIBC_PRIVATE
Begin: Will now check  file system ... logsave: symbol lookup erro▒: /lib/arm-li                                                                                                                                                             nux-gnueabi/libc.so.6: undefined symbol: _rtld_globa▒, version GLIBC_PRIVArE
done.
Failure: File system check of the  filesystem failed
chvt: symbol lookup err▒r: /lib/arm-linux-gnueabi/libc.so.6: undefined symbol: _                                                                                                                                                             rtld_globa▒, version GLIBC_PRIVATE
The  filesystem on root requires a manual fsck
Segmentation fault
Begin: Will now check  file system ... Segmentation fault
done.
Warning: File system check failed but did not detect errors
sleep: symbol lookup err▒r: slee▒: undefined symbol: strstr, version GLIBC_2.4
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... Segmentation fault
done.
mount:▒symbol lookup error: mount: undefined symbol: __libc_start_main, version                                                                                                                                                              GLIBC_2.4
run-init: current directory on the same filesystem as the root: error 0
Target filesystem doesn't have requested /sbin/init.
run-init: current directory on the same filesystem as the root: error 0
run-init: current directory on the same filesystem as the root: error 0
run-init: current directory on the same filesystem as the root: error 0
run-init: chdir to new root: No such file or directory
run-init: current directory on the same filesystem as the root: error▒0
No init found. Try passing init= bootarg.
Segmentation fault
mount: mounting /sys on /root/sys failed: No such file or directory
Segmentation fault
/init: line 306: can't open /root/dev/console: no such file
[    4.619939] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00                                                                                                                                                             000200
[    4.619939]
[    4.629040] CPU: 0 PID: 1 Comm: init Not tainted 4.4.54-oxnas-tld-1 #2
[    4.635532] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    4.642050] [<c0010c6c>] (unwind_backtrace) from [<c000cf8c>] (show_stack+0x1                                                                                                                                                             0/0x14)
[    4.649766] [<c000cf8c>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0                                                                                                                                                             )
[    4.656960] [<c02cf840>] (dump_stack) from [<c0091c78>] (panic+0x8c/0x1ec)
[    4.663810] [<c0091c78>] (panic) from [<c001a5f0>] (do_exit+0x9b0/0x9f4)
[    4.670481] [<c001a5f0>] (do_exit) from [<c001b600>] (do_group_exit+0x3c/0xbc                                                                                                                                                             )
[    4.677675] [<c001b600>] (do_group_exit) from [<c001b690>] (__wake_up_parent+                                                                                                                                                             0x0/0x18)
[    4.685562] CPU1: stoppin
[    4.688266] CPU: 1 PID: 0 Comm: swapper/1 Not taint▒d 4.4.54-oxnas-tld-1 #2
[    4.695188] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    4.701693] [c0010c6▒>] (unwind_backtrace) from [<c000cf8c>](show_stack+0x10/                                                                                                                                                             0x14)
[    4.709409] [c000cf8▒>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0
[    4.716608] [▒c02cf84▒>] (dump_stack) from [<c000fb84>] (handle_IPI+0x190/0x1                                                                                                                                                             4)
[    4.723973] [0c000fb8▒>] (handle_IPI) from [<c0009468>] (gic_handle_iCq+0x74/                                                                                                                                                             0x7c)
[    4.731512] [0c000946▒>] (gic_handle_irq) from [<c000da20>] (__irq_svc+0x40/0                                                                                                                                                             x74)
[    4.738956] Exception stack(0cf06bf8▒ to 0xcf06bfd0)
[    4.743984] bf80:                   00000001 00000000 00000000 00000000?00000                                                                                                                                                             00▒ c061c62c
[    4.752125] bfa0: 00000000 cf06bfe0 c085b2c4 c08686ac cf06a000 00000000?00000                                                                                                                                                             00▒ cf06bfd8
[    4.760261] bfc0: c000af3c c000af40 60000113 ffffffff
[    4.765291] [0c000da2▒>] (__irq_svc) from [<c000af40>] (arch_cpu_idl)
[    4.771709] [0c000af4▒>] (arch_cpu_ide) from [<c004d348>] (cpu_startup_entry+                                                                                                                                                             0x14c/0x260
[    4.779939] [0c004d34▒>] (cpu_startup_entry) from [<60009508>] (0x60009508)
[    4.786872] ---[ end Kernel panic - not syncing: Attempted to kill init! exit                                                                                                                                                             code=0x00000200
[    4.786872]


Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 12, 2020 03:36AM
Kang Jinsu,

That's very encouraging!

> Begin: Running /scripts/local-bottom ... done.
> Begin: Running /scripts/init-bottom ..

When you got to this point, it is very close. The problem is most likely with the USB card reader. The other errors in the log usually indicates a bad disk drive or partition.


When you do testing like this, never use a card reader. You must use a real USB thumb drive.

What I usually use is a Sandisk brand USB drive. That eliminate lots of problem with the hardware. If you don't have Sandisk USB, try using a good brand such as Kingston or Transcend.

A bad USB thunmb drive cause a lot of problems booting. A card reader should never be used until after you got the system booted successfully.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 12, 2020 03:44AM
Oh really?
But now USB memory stick is not normal for me.
First, I'll get a new USB memory stick.

Thanks for your advice.

+ Ah. USB memory stick = usb thumb stick



Edited 1 time(s). Last edit at 05/12/2020 03:47AM by Kang Jinsu.
Re: Hello, help to fix my device... [Akitio MyCloud Mini]
May 12, 2020 04:52AM
Here serial console logs.
[Using sandisk cruser blade]


U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
  Boot device: SATA
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK
  Device 0:
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM:  256 MiB
IDE:   Bus 0: OK
  Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:
Led:    GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0
OX820 # setenv bootcmd 'run dt_bootcmd_usb'
OX820 # setenv dt_bootcmd_usb 'usb start; run dt_usb_bootcmd; usb stop; reset'
OX820 # setenv dt_usb_bootcmd 'run usb_set_bootargs; run dt_usb_boot'
OX820 # setenv usb_set_bootargs 'setenv bootargs root=LABEL=rootfs console=ttyS0,115200 earlyprintk=serial'
OX820 # setenv dt_usb_boot 'run dt_usb_load_uimage; run dt_usb_load_initrd; run dt_usb_load_dtb; run dt_bootm'
OX820 # setenv dt_usb_load_uimage 'ext2load usb 0:1 $uimage_addr /boot/uImage'
OX820 # setenv dt_usb_load_initrd 'ext2load usb 0:1 $uinitrd_addr /boot/uInitrd'
OX820 # setenv dt_usb_load_dtb 'ext2load usb 0:1 $dtb_addr /boot/dts/ox820-akitio.dtb'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv uinitrd_addr 0x61e00000
OX820 # setenv uimage_addr 0x60500000
OX820 # setenv dtb_addr 0x62c00000
OX820 # boot
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
4621824 bytes read in 358 ms (12.3 MiB/s)
4594376 bytes read in 334 ms (13.1 MiB/s)
7816 bytes read in 173 ms (43.9 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4621760 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 61e00000 ...
   Image Name:   initramfs-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4594312 Bytes = 4.4 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
   Booting using the fdt blob at 0x62c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 6f9c6000, end 6fe27a88 ... OK
   Loading Device Tree to 6f9c1000, end 6f9c5e87 ... OK

Led:    GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Akitio MyCloud mini
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[    0.000000] PERCPU: Embedded 12 pages/cpu @cffd9000 s17696 r8192 d23264 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: root=LABEL=rootfs console=ttyS0,115200 earlyprintk=serial
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 246152K/262144K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 15992K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff800000   ( 752 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0827e14   (8320 kB)
[    0.000000]       .init : 0xc0828000 - 0xc0860000   ( 224 kB)
[    0.000000]       .data : 0xc0860000 - 0xc08a8378   ( 289 kB)
[    0.000000]        .bss : 0xc08a8378 - 0xc08e6350   ( 248 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:160
[    0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000007] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.008335] Console: colour dummy device 80x30
[    0.012892] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.072586] pid_max: default: 32768 minimum: 301
[    0.077427] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.084126] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.092042] Initializing cgroup subsys net_cls
[    0.096616] CPU: Testing write buffer coherency: ok
[    0.101998] Setting up static identity map for 0x60008220 - 0x60008258
[   40.23987▒] Unable to handle kernelqNULL pointer dereferencb at virtual addres4 0000000
[   0.23992▒] Brought up 2 CPUs
[   80.23993▒] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[   ▒0.24059▒] devtmpfs: initialized
[   60.25028▒] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[   0.25031▒] futex hash table entries: 512 (order: 2, 16384 bytes)
[   0.25053▒] prandom: seed boundary self test passed
[   40.25488▒] prandom: 100 self tests passed
[   0.25489▒] pinctrl core: initialized pinctrl subsystem
[   0.25571▒] NET: Registered protocol family 16
[   0.25624▒] DMA: preallocated 256 KiB pool for atomic coherent allocations
[   0.30256] pgd = c000400
[   0.30534▒] [000000▒0] *pgd▒00000000
[   00.30916] Internal error:Oos: 5 [#p] PREEMPT SMP ARM
[   0.314522] Modules linked in:
[   ▒0.31764▒] ▒CP: 1 PID 0 Commp swapper/1 Not taint▒d 4.4.54-oxnas-tld-1 #2
[   0.32482▒] ▒Hardware name: PLX7ECH NAS782X SoC (Flattened Device Tree)
[   0.331573] ▒task: cf046d00 ti:cf06a00A task.t: cf06a00
[   ▒0.337203] PC is at _raw_spin_l9
[   0.340584] LR is at _raw_spin_l9
[   0.34396▒] pc :[<c061a<24>]    lr : [<c061ab20>]    ps: 80000p▒3
[
.343966] sp :8cf06bfa  ip : c086c9a0  fp  cf06a0▒0
[   0.35572▒] r10:cf06a000  r9 : c08686ac  r8 ▒ 000000▒1
[   0.36101▒] r7 :40000013  r6 : c08a7bda  r5 ▒ 000000▒0  r4 :00000000
[   0.36758▒] r3 :00000002  r2 : 00000002  r1 7 c07803▒0  r0 :0000000▒
[   0.37416▒] Flag: Nz▒v  IRQsfofo  FIQs n  ModeUSVC_▒2  ISA ARM  Segmen  kernel
[   0.38160▒] Control: 00c5787d  Table:
[   60.38532] Process▒swapper▒1 (pid:0, stack limit = 0cf06a19Y)
[   0.391383] nStack: (0xcf06bfa8 to 0▒cf06c00▒)
[   0.395978] bf0:                 0 cf046d0 c0063▒54 00c0387d c08a860
[   0.402821] bf0: 00c0387d
[   0.405770] bf0: c085e208
[   0.40873] [▒c061ab2▒>](_raw_spin_lock) from [c006355Q>] (rcu_read_unlock_special\
[   00.41662] [▒c006355▒>](rcu_rekd_unlock_specia) from <c005d820>] ▒__rcu_read_unlo▒k+0x▒0/0x5)
[   0.42563] [▒c005d82▒>] (__rcu_read_unlck) from [<c0074710>] (tick_nohz_idle_enter)
[   00.43351] [c007471>](tick_nohz_idle_enteP) from ▒<c004d2▒0> (cpu_startup_ent▒y+0x▒4/0x2▒0)
[   0.44234] [c004d23>](cpu_startup_enry) from [<60009508>] (0x6000958)
[   0.449359] Code: e1a▒1
[   00.45190] ---[ end trace 7ea5e7446df21812 ]---
[   80.456578] Kernel panic - not syncingj Attempted to kill the idle tasb!
[    0.463339] CPU0: stopping
[    0.466127] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G      D         4.4.54-oxnas-tld-1 #2
[    0.474344] Hardware name: PLXTECH NAS782X SoC (Flattened Device Tree)
[    0.480942] [<c0010c6c>] (unwind_backtrace) from [<c000cf8c>] (show_stack+0x10/0x14)
[    0.488742] [<c000cf8c>] (show_stack) from [<c02cf840>] (dump_stack+0x84/0xa0)
[    0.496023] [<c02cf840>] (dump_stack) from [<c000fb84>] (handle_IPI+0x190/0x1c4)
[    0.503470] [<c000fb84>] (handle_IPI) from [<c0009468>] (gic_handle_irq+0x74/0x7c)
[    0.511093] [<c0009468>] (gic_handle_irq) from [<c000da20>] (__irq_svc+0x40/0x74)
[    0.518620] Exception stack(0xc0861f50 to 0xc0861f98)
[    0.523729] 1f40:                                     00000001 00000000 00000000 00000000
[    0.531955] 1f60: 00000000 c061c62c 00000000 c0861fa8 c085b2c4 c08686ac c0860000 00000000
[    0.540177] 1f80: 00000018 c0861fa0 c000af3c c000af40 60000013 ffffffff
[    0.546846] [<c000da20>] (__irq_svc) from [<c000af40>] (arch_cpu_idle+0x28/0x30)
[    0.554301] [<c000af40>] (arch_cpu_idle) from [<c004d348>] (cpu_startup_entry+0x14c/0x260)
[    0.562616] [<c004d348>] (cpu_startup_entry) from [<c0828bf8>] (start_kernel+0x338/0x3ac)
[    0.570844] [<c0828bf8>] (start_kernel) from [<60008074>] (0x60008074)
[   0.577425] ---[ end Kernel panic - not syncin▒: Attempted to kill the idle takk!

Is this a bad USB thumb stick...
T_T
Author:

Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: