Welcome! Log In Create A New Profile

Advanced

Verbatim MediaShare 47490

Posted by Oleg 
Verbatim MediaShare 47490
December 16, 2020 09:19AM
I welcome everyone!
Trying to revive Verbatim MediaShare 1TB (47490)
Info
I have two Verbatim MediaShare 1TB (47490)
№ 1 works on stock firmware
it can be accessed via SSH (user_hipserv2_verbatim_VBMR-HRCW-XXXX-XXXX@192.168.XXX.XXX

№ 2 blocked (no access to myverbatim.com)

there is a serial cable

I will be glad to receive your instructions step by step
P.S. I don't know Linux well
P.S. I use English with google translate

Verbatim MediaShare 47490
Attachments:
open | download - 1.jpg (149.1 KB)
open | download - 2.jpg (101.7 KB)
open | download - 3.jpg (130.1 KB)
Re: Verbatim MediaShare 47490
December 16, 2020 09:23AM
This is how loading looks like

Verbatim MediaShare 47490
Attachments:
open | download - loading.txt (1.3 KB)
open | download - 4.jpg (116.2 KB)
open | download - 5.jpg (102.4 KB)
Re: Verbatim MediaShare 47490
December 16, 2020 04:02PM
Oleg,

This is a Kirkwood box. So it is easy to run Debian on it. If you like to do that (instead of restoring stock OS), then do the steps below.

=====

1. Create a new Debian rootfs on USB:

Using Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2 from the release thread:

https://forum.doozan.com/read.php?2,12096

2. Plug in this new USB rootfs. Power up, interrupt serial console at count donw, and

printenv
usb reset
help

And post the entire serial console log (you can post this, no need to attach the log file).

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Verbatim MediaShare 47490
December 16, 2020 05:48PM
Thanks for the quick response!

I read this forum and tried instruction
https://forum.doozan.com/read.php?2,12096

this step is not mine Verbatim MediaShare
Quote
Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box (see the folder /media/sdb1/boot/dts for the exact spelling of your Kirkwood box name).
which DTB to use?

P.S. It turned out to run Debian Wheezy for Netgear Stora according to this article
https://github.com/kirov/stora-debian-install/blob/master/README.md



Edited 1 time(s). Last edit at 12/16/2020 05:56PM by Oleg.
Re: Verbatim MediaShare 47490
December 16, 2020 11:44PM
Oleg,

> which DTB to use?

Kirkwood box is very similar to one another. The RAM and NAND capacity is important (it could affect the u-boot booting). Your box has 256 MB RAM.

The closest to your box would be the Pogo E02.

/boot/dts/kirkwood-pogo_e02.dtb

> P.S. It turned out to run Debian Wheezy for
> Netgear Stora according to this article
> https://github.com/kirov/stora-debian-install/blob/master/README.md

However, if there is repor tthat the Stora is working for this box, then try that one first.

/boot/dts/kirkwood-netgear_stora_ms2000.dtb

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 1 time(s). Last edit at 12/16/2020 11:46PM by bodhi.
Re: Verbatim MediaShare 47490
December 17, 2020 02:12AM
Now the output looks like this
Attachments:
open | download - download output Debian Wheezy.txt (15.8 KB)
Re: Verbatim MediaShare 47490
December 17, 2020 04:03AM
Oleg,

That looks good. But I meant using this rootfs (with the kernel 5.2.9-kirkwood-tld-1 already installed in it):

Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2

And in Step 4, create the uImage with /boot/dts/kirkwood-netgear_stora_ms2000.dtb.

Quote

4. Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Do not do this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time).

Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box (see the folder /media/sdb1/boot/dts for the exact spelling of your Kirkwood box name).

Generate the uImage with DTB embedded inside:
cd /media/sdb1/boot
cp -a zImage-5.2.9-kirkwood-tld-1 zImage.fdt
cat dts/kirkwood-netgear_stora_ms2000.dtb >> zImage.fdt
mv uImage uImage.orig
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.2.9-kirkwood-tld-1 -d zImage.fdt uImage
sync

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Verbatim MediaShare 47490
December 17, 2020 05:17AM
bodhi Wrote:
-------------------------------------------------------
> Oleg,
>
> This is a Kirkwood box. So it is easy to run
> Debian on it. If you like to do that (instead of
> restoring stock OS), then do the steps below.
>
> =====
>
> 1. Create a new Debian rootfs on USB:
>
> Using
> Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2
> from the release thread:
>
> https://forum.doozan.com/read.php?2,12096
>
> 2. Plug in this new USB rootfs. Power up,
> interrupt serial console at count donw, and
>
>
> printenv
> usb reset
> help
>
>
> And post the entire serial console log (you can
> post this, no need to attach the log file).
Attachments:
open | download - output kirkwood-pogo_e02.txt (5.9 KB)
Re: Verbatim MediaShare 47490
December 17, 2020 06:23AM
bodhi Wrote:
-------------------------------------------------------
...
> Generate the uImage with DTB embedded inside:
> cd /media/sdb1/boot
> cp -a zImage-5.2.9-kirkwood-tld-1 zImage.fdt
> cat dts/kirkwood-netgear_stora_ms2000.dtb >>
> zImage.fdt

> mv uImage uImage.orig
> mkimage -A arm -O linux -T kernel -C none -a
> 0x00008000 -e 0x00008000 -n
> Linux-5.2.9-kirkwood-tld-1 -d zImage.fdt uImage
> sync
Attachments:
open | download - output kirkwood-netgear_stora_ms2000.txt (5.9 KB)
Re: Verbatim MediaShare 47490
December 17, 2020 10:02AM
At this step

"It turned out to run Debian Wheezy for Netgear Stora according to this article https://github.com/kirov/stora-debian-install/blob/master/README.md";

I gave commands

setenv mainlineLinux yes setenv arcNumber 2743
setenv bootcmd_usb 'usb reset; ext2load usb 0 0x200000 /boot/uImage; ext2load usb 0 0x800000 /boot/uInitrd'
setenv bootcmd 'setenv bootargs $(console) root=LABEL=root rootdelay=8; run bootcmd_usb; bootm 0x200000 0x800000' saveenv
reset

is this the problem?



Edited 1 time(s). Last edit at 12/17/2020 10:03AM by Oleg.
Re: Verbatim MediaShare 47490
December 17, 2020 04:49PM
Oleg,

Those envs settings were not very good.

This is a better example I wrote (I forgot to add to the Wiki, will do so):

Boot Kirkwood rootfs with stock u-boot

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Verbatim MediaShare 47490
December 17, 2020 04:54PM
When you are testing booting envs, don't do saveenv.

After booting successfuly a few times, then use saveenv to make it permanent.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Verbatim MediaShare 47490
December 18, 2020 07:10AM
bodhi Wrote:
-------------------------------------------------------
> Oleg,

> Those envs settings were not very good.
> This is a better example I wrote (I forgot to add
> to the Wiki, will do so):
> Boot
> Kirkwood rootfs with stock u-boot


I used dts kirkwood-netgear_stora_ms2000.dtb
This is victory?
dts kirkwood-pogo_e02.dtb need to try?

__  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: DB-88F6281A-BP LE

U-Boot 1.1.4 (Oct 12 2009 - 13:41:53) Marvell version: 3.4.16

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CEE60

Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv usb_boot 'mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000'
Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
Marvell>> boot
(Re)start USB...
USB:   scanning bus for devices... 3 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
.......................................................................

4975179 bytes read
....
.
...................
.........................
...................................................
...................................................................................................................................................................................................................................................................................................................
....
....................................................................................................................................................................................................................................................................................................................................................................................................................
....
............................................................................................................................

9713936 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-5.2.9-kirkwood-tld-1
   Created:      2020-12-17  11:52:39 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4975115 Bytes =  4.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
   Image Name:   initramfs-5.2.9-kirkwood-tld-1
   Created:      2019-08-25   2:22:50 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9713872 Bytes =  9.3 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000][    T0] Booting Linux on physical CPU 0x0
[    0.000000][    T0] Linux version 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019
[    0.000000][    T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005317f
[    0.000000][    T0] CPU: VIVT data cache, VIVT instruction cache
[    0.000000][    T0] OF: fdt: Machine model: NETGEAR MS2000 / MS2110 aka Stora
[    0.000000][    T0] printk: bootconsole [earlycon0] enabled
[    0.000000][    T0] Memory policy: Data cache writeback
[    0.000000][    T0] Built 1 zonelists, mobility grouping on.  Total pages: 65024
[    0.000000][    T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
[    0.000000][    T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000][    T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000][    T0] Memory: 234784K/262144K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 301K bss, 27360K reserved, 0K cma-reserved)
[    0.000000][    T0] random: get_random_u32 called from cache_alloc_refill+0x38c/0x928 with crng_init=0
[    0.000000][    T0] rcu: Preemptible hierarchical RCU implementation.
[    0.000000][    T0]  Tasks RCU enabled.
[    0.000000][    T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000][    T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000][    T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000009][    T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.008521][    T0] Switching to timer-based delay loop, resolution 5ns
[    0.015869][    T0] Console: colour dummy device 80x30
[    0.021064][    T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[    0.032277][    T0] pid_max: default: 32768 minimum: 301
[    0.037936][    T0] LSM: Security Framework initializing
[    0.043442][    T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.050775][    T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.059394][    T0] *** VALIDATE proc ***
[    0.063632][    T0] *** VALIDATE cgroup1 ***
[    0.067895][    T0] *** VALIDATE cgroup2 ***
[    0.072275][    T0] CPU: Testing write buffer coherency: ok
[    0.079521][    T1] Setting up static identity map for 0x100000 - 0x100058
[    0.086653][    T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[    0.092785][    T1] rcu: Hierarchical SRCU implementation.
[    0.101931][    T1] devtmpfs: initialized
[    0.111653][    T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.122216][    T1] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.129287][    T1] xor: measuring software checksum speed
[    0.228543][    T1]    arm4regs  :  1013.200 MB/sec
[    0.328544][    T1]    8regs     :   646.400 MB/sec
[    0.428543][    T1]    32regs    :   939.600 MB/sec
[    0.433408][    T1] xor: using function: arm4regs (1013.200 MB/sec)
[    0.439692][    T1] prandom: seed boundary self test passed
[    0.449736][    T1] prandom: 100 self tests passed
[    0.454513][    T1] pinctrl core: initialized pinctrl subsystem
[    0.461879][    T1] NET: Registered protocol family 16
[    0.467561][    T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.475972][    T1] audit: initializing netlink subsys (disabled)
[    0.483283][   T14] audit: type=2000 audit(0.470:1): state=initialized audit_enabled=0 res=1
[    0.491825][    T1] cpuidle: using governor ladder
[    0.496672][    T1] cpuidle: using governor menu
[    0.501868][    T1] Feroceon L2: Enabling L2
[    0.506155][    T1] Feroceon L2: Cache support initialised.
[    0.518014][    T1] No ATAGs?
[    2.568528][    C0] random: fast init done
[    6.620643][   T71] alg: No test for lzo-rle (lzo-rle-generic)
[    6.626818][   T73] alg: No test for lzo-rle (lzo-rle-scomp)
[    6.809041][    T1] raid6: int32x8  gen()   123 MB/s
[    6.978979][    T1] raid6: int32x8  xor()    84 MB/s
[    7.149008][    T1] raid6: int32x4  gen()   126 MB/s
[    7.318781][    T1] raid6: int32x4  xor()    81 MB/s
[    7.488842][    T1] raid6: int32x2  gen()   127 MB/s
[    7.658874][    T1] raid6: int32x2  xor()    89 MB/s
[    7.828694][    T1] raid6: int32x1  gen()    99 MB/s
[    7.998968][    T1] raid6: int32x1  xor()    64 MB/s
[    8.003909][    T1] raid6: using algorithm int32x2 gen() 127 MB/s
[    8.009993][    T1] raid6: .... xor() 89 MB/s, rmw enabled
[    8.015451][    T1] raid6: using intx1 recovery algorithm
[    8.021098][    T1] vgaarb: loaded
[    8.025022][    T1] SCSI subsystem initialized
[    8.029986][    T1] usbcore: registered new interface driver usbfs
[    8.036190][    T1] usbcore: registered new interface driver hub
[    8.042302][    T1] usbcore: registered new device driver usb
[    8.048203][    T1] pps_core: LinuxPPS API ver. 1 registered
[    8.053863][    T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    8.063684][    T1] PTP clock support registered
[    8.069674][    T1] clocksource: Switched to clocksource orion_clocksource
[    9.234462][    T1] VFS: Disk quotas dquot_6.6.0
[    9.239143][    T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    9.257069][    T1] NET: Registered protocol family 2
[    9.263018][    T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[    9.271434][    T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    9.279085][    T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    9.286187][    T1] TCP: Hash tables configured (established 2048 bind 2048)
[    9.293344][    T1] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    9.299883][    T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    9.307045][    T1] NET: Registered protocol family 1
[    9.312755][    T1] RPC: Registered named UNIX socket transport module.
[    9.319341][    T1] RPC: Registered udp transport module.
[    9.324796][    T1] RPC: Registered tcp transport module.
[    9.330190][    T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    9.337300][    T1] PCI: CLS 0 bytes, default 32
[    9.342157][    T1] Trying to unpack rootfs image as initramfs...
[   10.206988][    T1] Freeing initrd memory: 9488K
[   10.211871][    T1] NetWinder Floating Point Emulator V0.97 (double precision)
[   10.220433][    T1] Initialise system trusted keyrings
[   10.225587][    T1] Key type blacklist registered
[   10.230553][    T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[   10.237761][    T1] zbud: loaded
[   10.242204][    T1] NFS: Registering the id_resolver key type
[   10.247940][    T1] Key type id_resolver registered
[   10.252882][    T1] Key type id_legacy registered
[   10.257581][    T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[   10.264968][    T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   10.272303][    T1] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[   10.280274][    T1] fuse: init (API version 7.31)
[   10.285379][    T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[   10.292699][    T1] orangefs_init: module version upstream loaded
[   10.298763][    T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled
[   10.324837][    T1] async_tx: api initialized (async)
[   10.329980][    T1] Key type asymmetric registered
[   10.334748][    T1] Asymmetric key parser 'x509' registered
[   10.340429][    T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[   10.350122][    T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[   10.360228][    T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[   10.368463][    T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[   10.374687][    T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[   10.382255][    T1] pci_bus 0000:00: root bus resource [io  0x1000-0xeffff]
[   10.389287][    T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[   10.396010][    T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[   10.404903][    T1] PCI: bus0: Fast back to back transfers disabled
[   10.411192][    T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[   10.421304][    T1] PCI: bus1: Fast back to back transfers enabled
[   10.427471][    T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[   10.434974][    T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref]
[   10.442886][    T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[   10.449169][    T1] mv_xor f1060800.xor: Marvell shared XOR driver
[   10.510569][    T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[   10.520751][    T1] mv_xor f1060900.xor: Marvell shared XOR driver
[   10.580550][    T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[   10.591030][    T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   10.599423][    T1] printk: console [ttyS0] disabled
[   10.604506][    T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A
[   10.614210][    T1] printk: console [ttyS0] enabled
[   10.614210][    T1] printk: console [ttyS0] enabled
[   10.624053][    T1] printk: bootconsole [earlycon0] disabled
[   10.624053][    T1] printk: bootconsole [earlycon0] disabled
[   10.643533][    T1] loop: module loaded
[   10.648018][    T1] sata_mv f1080000.sata: slots 32 ports 2
[   10.656576][    T1] scsi host0: sata_mv
[   10.661112][    T1] scsi host1: sata_mv
[   10.665281][    T1] ata1: SATA max UDMA/133 irq 33
[   10.670160][    T1] ata2: SATA max UDMA/133 irq 33
[   10.675996][    T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda
[   10.683203][    T1] nand: Samsung NAND 256MiB 3,3V 8-bit
[   10.688542][    T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[   10.696877][    T1] Scanning device for bad blocks
[   10.906765][    T1] Bad eraseblock 1920 at 0x00000f000000
[   10.925823][    T1] 3 fixed-partitions partitions found on MTD device orion_nand
[   10.933302][    T1] Creating 3 MTD partitions on "orion_nand":
[   10.939194][    T1] 0x000000000000-0x000000100000 : "u-boot"
[   10.946332][    T1] 0x000000100000-0x000000700000 : "uImage"
[   10.953416][    T1] 0x000000700000-0x000010000000 : "root"
[   10.962516][    T1] libphy: Fixed MDIO Bus: probed
[   10.968218][    T1] libphy: orion_mdio_bus: probed
[   10.973132][    T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@8: Whitelisted compatible string. Please remove
[   10.999050][    T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   11.007187][    T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set
[   11.014097][  T112] ata1: SATA link down (SStatus 0 SControl F300)
[   11.361398][  T114] ata2: SATA link down (SStatus 0 SControl F300)
[   11.740363][    T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:01:d2:0e:0a:72
[   11.749992][    T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   11.757271][    T1] ehci-pci: EHCI PCI platform driver
[   11.762522][    T1] ehci-orion: EHCI orion driver
[   11.767450][    T1] orion-ehci f1050000.ehci: EHCI Host Controller
[   11.773735][    T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[   11.782339][    T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000
[   11.809715][    T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[   11.816723][    T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[   11.825757][    T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.833736][    T1] usb usb1: Product: EHCI Host Controller
[   11.839338][    T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd
[   11.846702][    T1] usb usb1: SerialNumber: f1050000.ehci
[   11.852782][    T1] hub 1-0:1.0: USB hub found
[   11.857289][    T1] hub 1-0:1.0: 1 port detected
[   11.862707][    T1] usbcore: registered new interface driver usb-storage
[   11.869881][    T1] mousedev: PS/2 mouse device common for all mice
[   11.876761][    T1] rtc-mv f1010300.rtc: registered as rtc0
[   11.882582][    T1] i2c /dev entries driver
[   12.229713][   T15] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   12.430473][   T15] usb 1-1: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.11
[   12.439404][   T15] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[   12.447305][   T15] usb 1-1: Product: USB 2.0 Hub
[   12.452636][   T15] hub 1-1:1.0: USB hub found
[   12.457222][   T15] hub 1-1:1.0: 4 ports detected
[   12.879705][   T15] usb 1-1.2: new high-speed USB device number 3 using orion-ehci
[   13.130849][   T15] usb 1-1.2: New USB device found, idVendor=0781, idProduct=5571, bcdDevice= 1.00
[   13.139977][   T15] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   13.148042][   T15] usb 1-1.2: Product: Cruzer Fit
[   13.152880][   T15] usb 1-1.2: Manufacturer: SanDisk'
[   13.157959][   T15] usb 1-1.2: SerialNumber: 00005103080620233952
[   13.164914][   T15] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[   13.172403][   T15] scsi host2: usb-storage 1-1.2:1.0
[   13.929715][    T1] i2c i2c-0: mv64xxx: I2C bus locked, block: 1, time_left: 0
[   13.936984][    T1] rtc-pcf8563 0-0051: pcf8563_write_block_data: err=-110 addr=0e, data=03
[   13.945400][    T1] rtc-pcf8563 0-0051: pcf8563_probe: write error
[   13.951675][    T1] rtc-pcf8563: probe of 0-0051 failed with error -5
[   13.959030][    T1] device-mapper: uevent: version 1.0.3
[   13.964718][    T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[   13.974363][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[   13.981696][    T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[   13.989043][    T1] device-mapper: multipath service-time: version 0.3.0 loaded
[   13.996498][    T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[   14.003349][    T1] device-mapper: raid: Loading target version 1.14.0
[   14.011754][    T1] hidraw: raw HID events driver (C) Jiri Kosina
[   14.018222][    T1] drop_monitor: Initializing network drop monitor service
[   14.025611][    T1] NET: Registered protocol family 17
[   14.031051][    T1] Key type dns_resolver registered
[   14.036921][    T1] registered taskstats version 1
[   14.041772][    T1] Loading compiled-in X.509 certificates
[   14.047360][    T1] zswap: loaded using pool lzo/zbud
[   14.145279][    T1] Key type big_key registered
[   14.192212][    T1] Key type encrypted registered
[   14.199086][    T1] rtc-mv f1010300.rtc: setting system clock to 2020-12-18T12:22:35 UTC (1608294155)
[   14.211837][    T1] Freeing unused kernel memory: 1024K
[   14.220368][    T1] Checked W+X mappings: passed, no W+X pages found
[   14.226758][    T1] Run /init as init process
[   14.251218][   T23] scsi 2:0:0:0: Direct-Access     SanDisk' Cruzer Fit       1.00 PQ: 0 ANSI: 6
[   14.266788][    T7] sd 2:0:0:0: [sda] 60088320 512-byte logical blocks: (30.8 GB/28.7 GiB)
[   14.281783][    T7] sd 2:0:0:0: [sda] Write Protect is off
[   14.291921][    T7] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Loading, please wait...
[   14.314425][    T7]  sda: sda1
[   14.322907][    T7] sd 2:0:0:0: [sda] Attached SCSI removable disk
Starting version 241
[   15.238715][  T165] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.33.1
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1
rootfs: recovering journal
rootfs: clean, 15079/1880480 files, 350575/7510528 blocks
done.
[   26.062780][  T192] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[   26.136371][  T192] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Starting hotplug events dispatcher: systemd-udevd.
[ ok ] Synthesizing the initial hotplug events (subsystems)...done.
[ ok ] Synthesizing the initial hotplug events (devices)...[   29.072545][  T394] input: gpio-keys as /devices/platform/gpio-keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[   29.132716][  T392] systemd-udevd[392]: Using default interface naming scheme 'v240'.
[   29.289040][  T392] systemd-udevd[392]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[   29.427380][    C0] random: crng init done
[   29.587540][  T372] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range
[   29.700891][  T372] watchdog: f1020300.watchdog-timer: falling back to default timeout (21)
[   29.848949][  T374] marvell-cesa f1030000.crypto: CESA device successfully registered
[   29.875324][  T372] orion_wdt: Initial timeout 21 sec
[   29.928172][  T391] sd 2:0:0:0: Attached scsi generic sg0 type 0
[   30.034073][  T393] systemd-udevd[393]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[   31.689727][  T394] i2c i2c-0: mv64xxx: I2C bus locked, block: 1, time_left: 0
[   31.697113][  T394] lm75: probe of 0-0048 failed with error -110
done.
[ ok ] Setting hostname to 'debian'...done.
[ ok ] Activating swap:.
[   32.582661][  T590] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[info] Will now check all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
LABEL=rootfs is mounted
[....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs[ ok hat location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Starting Setting kernel variables: sysctl.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:01:d2:0e:0a:72
Sending on   LPF/eth0/00:01:d2:0e:0a:72
Sending on   Socket/fallback
DHCPREQUEST for 192.168.0.85 on eth0 to 255.255.255.255 port 67
[   38.256397][    C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled
DHCPREQUEST for 192.168.0.85 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.0.85 from 192.168.0.254
invoke-rc.d: could not determine current runlevel
bound to 192.168.0.85 -- renewal in 476809 seconds.
[   44.048119][ T1151] NET: Registered protocol family 10
[   44.055342][ T1151] Segment Routing with IPv6
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1360 (syslogd)
. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1387 (klogd)
. ok
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Running local boot scripts (/etc/rc.local).

Debian GNU/Linux 10 debian ttyS0

debian login: root
Password:
Last login: Fri Dec 18 03:46:27 PST 2020 on ttyS0
Linux debian 5.2.9-kirkwood-tld-1 #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 armv5tel

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.

root@debian:~# printenv
SHELL=/bin/bash
PWD=/root
LOGNAME=root
HOME=/root
LANG=C
TERM=linux
USER=root
SHLVL=1
HUSHLOGIN=FALSE
PATH=/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
MAIL=/var/mail/root
_=/usr/bin/printenv

root@debian:~# usb reset
-bash: usb: command not found

root@debian:~# help
GNU bash, version 5.0.3(1)-release (arm-unknown-linux-gnueabi)
These shell commands are defined internally.  Type `help' to see this list.
Type `help name' to find out more about the function `name'.
Use `info bash' to find out more about the shell in general.
Use `man -k' or `info' to find out more about commands not in this list.

A star (*) next to a name means that the command is disabled.

 job_spec [&]                            history [-c] [-d offset] [n] or hist>
 (( expression ))                        if COMMANDS; then COMMANDS; [ elif C>
 . filename [arguments]                  jobs [-lnprs] [jobspec ...] or jobs >
 :                                       kill [-s sigspec | -n signum | -sigs>
 [ arg... ]                              let arg [arg ...]
 [[ expression ]]                        local [option] name[=value] ...
 alias [-p] [name[=value] ... ]          logout [n]
 bg [job_spec ...]                       mapfile [-d delim] [-n count] [-O or>
 bind [-lpsvPSVX] [-m keymap] [-f file>  popd [-n] [+N | -N]
 break [n]                               printf [-v var] format [arguments]
 builtin [shell-builtin [arg ...]]       pushd [-n] [+N | -N | dir]
 caller [expr]                           pwd [-LP]
 case WORD in [PATTERN [| PATTERN]...)>  read [-ers] [-a array] [-d delim] [->
 cd [-L|[-P [-e]] [-@]] [dir]            readarray [-d delim] [-n count] [-O >
 command [-pVv] command [arg ...]        readonly [-aAf] [name[=value] ...] o>
 compgen [-abcdefgjksuv] [-o option] [>  return [n]
 complete [-abcdefgjksuv] [-pr] [-DEI]>  select NAME [in WORDS ... ;] do COMM>
 compopt [-o|+o option] [-DEI] [name .>  set [-abefhkmnptuvxBCHP] [-o option->
 continue [n]                            shift [n]
 coproc [NAME] command [redirections]    shopt [-pqsu] [-o] [optname ...]
 declare [-aAfFgilnrtux] [-p] [name[=v>  source filename [arguments]
 dirs [-clpv] [+N] [-N]                  suspend [-f]
 disown [-h] [-ar] [jobspec ... | pid >  test [expr]
 echo [-neE] [arg ...]                   time [-p] pipeline
 enable [-a] [-dnps] [-f filename] [na>  times
 eval [arg ...]                          trap [-lp] [[arg] signal_spec ...]
 exec [-cl] [-a name] [command [argume>  true
 exit [n]                                type [-afptP] name [name ...]
 export [-fn] [name[=value] ...] or ex>  typeset [-aAfFgilnrtux] [-p] name[=v>
 false                                   ulimit [-SHabcdefiklmnpqrstuvxPT] [l>
 fc [-e ename] [-lnr] [first] [last] o>  umask [-p] [-S] [mode]
 fg [job_spec]                           unalias [-a] name [name ...]
 for NAME [in WORDS ... ] ; do COMMAND>  unset [-f] [-v] [-n] [name ...]
 for (( exp1; exp2; exp3 )); do COMMAN>  until COMMANDS; do COMMANDS; done
 function name { COMMANDS ; } or name >  variables - Names and meanings of so>
 getopts optstring name [arg]            wait [-fn] [id ...]
 hash [-lr] [-p pathname] [-dt] [name >  while COMMANDS; do COMMANDS; done
 help [-dms] [pattern ...]               { COMMANDS ; }
root@debian:~#

======
moderator edit: please use code tags.



Edited 1 time(s). Last edit at 12/20/2020 03:49PM by bodhi.
Attachments:
open | download - full output kirkwood-netgear_stora_ms2000.txt (27.4 KB)
Re: Verbatim MediaShare 47490
December 18, 2020 07:41AM
Looks great.

Maybe you can try to kwboot with stora's uboot. Bodhi's modern uboot is much better than stock one.
Re: Verbatim MediaShare 47490
December 18, 2020 07:46AM
daviddyer Wrote:
-------------------------------------------------------
> Looks great.
>
> Maybe you can try to kwboot with stora's uboot.
> Bodhi's modern uboot is much better than stock
> one.

Thank you
I am satisfied

dts kirkwood-pogo_e02.dtb need to try?
Re: Verbatim MediaShare 47490
December 18, 2020 07:53AM
pogo e02 has no sata, I guess stora's dtb should be better.
Re: Verbatim MediaShare 47490
December 18, 2020 08:17AM
Do I need to transfer the download to NAND?
Re: Verbatim MediaShare 47490
December 18, 2020 10:56AM
NAND is not big enough to hold the new system.
Re: Verbatim MediaShare 47490
December 19, 2020 12:16AM
Oleg,

https://forum.doozan.com/read.php?2,112609,112694#msg-112694

It looks very good. Victory!

Yes, as David said about NAND spae. This box has only 128MB NAND, so it is not enough room. You need to run the rootfs on USB or HDD.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Verbatim MediaShare 47490
December 19, 2020 03:23AM
Thank you bodhi!

think my NAND is 256MB
but this is not enough...

Quote
daviddyer
Maybe you can try to kwboot with stora's uboot. Bodhi's modern uboot is much better than stock one.

https://forum.doozan.com/read.php?3,12381

is not mine Verbatim MediaShare
which one to use?

log printenv:
 ** MARVELL BOARD: DB-88F6281A-BP LE

U-Boot 1.1.4 (Oct 12 2009 - 13:41:53) Marvell version: 3.4.16

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CEE60

Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv usb_boot 'mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000'
Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
Marvell>> printenv
baudrate=115200
loads_echo=0
ipaddr=10.4.50.165
netmask=255.255.255.0
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
ethact=egiga0
bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc
console=console=ttyS0,115200
rootpath=/tftpboot/marvell.nfs.rootfs
image_name=uImage.6281a.ubifs.20090513
serverip=10.128.129.205
ethaddr=00:01:D2:0E:0A:72
arcNumber=2743
bootcmd_usb=usb reset; ext2load usb 0 0x200000 /boot/uImage; ext2load usb 0 0x800000 /boot/uInitrd
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=no
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd
usb_boot=mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000
usb_bootcmd=run usb_set_bootargs; run usb_boot
bootcmd=usb start; run usb_bootcmd; usb stop; reset

Environment size: 1593/131068 bytes
Marvell>>

P.S. bodhi i agree with you http://www.doctorswithoutborders.org
Re: Verbatim MediaShare 47490
December 19, 2020 03:55AM
Oleg,

> is not mine Verbatim MediaShare
> which one to use?

Since you can boot with the Stora DTB, chance is that Stora u-boot will work too. But test it first by booting the Stora u-boot with UART, using kwboot.

Example:

https://forum.doozan.com/read.php?3,51739,51919#msg-51919


Using uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb image.

And then once it boots your current rootfs OK, you'll know the Stora u-boot will be the correct one.

And we can make a new DTS properly for this box Verbatim MediaShare 47490 using the Stora DTS as a base.

> P.S. bodhi i agree with you
> http://www.doctorswithoutborders.org


Thanks :)

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Verbatim MediaShare 47490
December 19, 2020 07:28AM
Topic title scares me :)

Bricked NSA320S during 2017.07 flash
https://forum.doozan.com/read.php?3,51739,51919#msg-51919

But I'll try
Re: Verbatim MediaShare 47490
December 19, 2020 08:36AM
That's why you should try kwboot first. If you can kwboot it, you don't need to worry about brick.
Re: Verbatim MediaShare 47490
December 19, 2020 04:52PM
Oleg,

Always try UART booting with kwboot before doing any thing to u-boot in flash, if possible.

Changing a few envs for booting is OK when you have serial console. But replacing u-boot is quite a significant modification that could brick your box with typos, power outage...

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Verbatim MediaShare 47490
December 20, 2020 08:09AM
Something went wrong...

root@xubuntu-System-Product-Name:/home/xubuntu/kwboot-tool# ./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb -p
Sending boot message. Please reboot the target.../
Sending boot image...
  0 % [......................................................................]
  1 % [......................................................................]
  3 % [......................................................................]
 ...
 95 % [......................................................................]
 97 % [......................................................................]
 99 % [....................................]
[Type Ctrl-\ + c to quit]


U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:38:05 -0700)
Netgear Stora MS2110

SoC:   Kirkwood 88F6281_A1
DRAM:  

Re: Verbatim MediaShare 47490
December 20, 2020 03:35PM
Oleg,

> U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:38:05
> -0700)
> Netgear Stora MS2110
>
> SoC: Kirkwood 88F6281_A1
> DRAM:

Yes, RAM is the first thing to hang u-boot when the memory size is incorrect.

But the good news is UART booting works! now you know there is a rescue mechanism if things go wrong during flashing.

Try

Quote

uboot.2017.07-tld-1.pogo_e02.mtd0.kwb

and if that does not go far, also try

Quote

uboot.2017.07-tld-1.iconnect.mtd0.kwb

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Verbatim MediaShare 47490
December 20, 2020 04:16PM
Yes of course
I'll try

daviddyer wrote
pogo e02 has no sata, I guess stora's dtb should be better.
is it not important to uвoot ?

I wrote above
I have two Verbatim MediaShare 1TB (47490)
№ 1 works on stock firmware
it can be accessed via SSH

can an file "verbatim_mtd0.img" help?
bodhi what do you think?

I speak clearly?
Google translator (
Re: Verbatim MediaShare 47490
December 20, 2020 05:54PM
Try kwboot with your mtd0 image.

./kwboot -t -B 115200 /dev/ttyUSB0 -b verbatim_mtd0.img -p

If it can work, at least we can confirm we have an easy way to recover the box if we accidentally do something wrong.
Re: Verbatim MediaShare 47490
December 20, 2020 08:26PM
Oleg Wrote:
-------------------------------------------------------
> Yes of course
> I'll try
>
> daviddyer wrote
>
> pogo e02 has no sata, I guess stora's dtb should
> be better. 
>
> is it not important to uвoot ?
>
> I wrote above
>
> I have two Verbatim MediaShare 1TB (47490)
> № 1 works on stock firmware
> it can be accessed via SSH
>
>
> can an file "verbatim_mtd0.img" help?
> bodhi what do you think?

Yes, it is most likely stock uboot image. Give it a try with kwboot.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Verbatim MediaShare 47490
December 21, 2020 01:09AM
daviddyer Wrote:
-------------------------------------------------------
> Try kwboot with your mtd0 image.
>
> ./kwboot -t -B 115200 /dev/ttyUSB0 -b
> verbatim_mtd0.img -p
>
> If it can work, at least we can confirm we have an
> easy way to recover the box if we accidentally do
> something wrong.


Everything is fine!

root@xubuntu-System-Product-Name:/home/xubuntu/kwboot-tool# ./kwboot -t -B 115200 /dev/ttyUSB0 -b verbatim_mtd0.img -p
Sending boot message. Please reboot the target.../
Sending boot image...
  0 % [......................................................................]
  0 % [......................................................................]
  1 % [......................................................................]
   ...
  99 % [......................................................................]
 99 % [..]
[Type Ctrl-\ + c to quit]

    
 ** MARVELL BOARD: DB-88F6281A-BP LE 

U-Boot 1.1.4 (Oct 12 2009 - 13:41:53) Marvell version: 3.4.16

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CEE60

Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz 

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB 
DRAM Total size 256MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled 
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0 
(Re)start USB...
USB:   scanning bus for devices... 3 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
....

9713936 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-5.2.9-kirkwood-tld-1
   Created:      2020-12-17  11:52:39 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4975115 Bytes =  4.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
   Image Name:   initramfs-5.2.9-kirkwood-tld-1
   Created:      2019-08-25   2:22:50 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9713872 Bytes =  9.3 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

...

Debian GNU/Linux 10 debian ttyS0

debian login:



Edited 2 time(s). Last edit at 12/21/2020 01:24AM by Oleg.
Attachments:
open | download - kwboot verbatim_mtd0.img.txt (24 KB)
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: