|
Unknown compression type for in .//var/cache/apt/archives/libacl1_2.2.49-4_armel.deb May 31, 2013 10:23PM |
Registered: 10 years ago Posts: 8 |
!!!!! DANGER DANGER DANGER DANGER DANGER DANGER !!!!!!
This script will replace the bootloader on /dev/mtd0.
If you lose power while the bootloader is being flashed,
your device could be left in an unusable state.
This script will configure your Dockstar to boot Debian Squeeze
from a USB device. Before running this script, you should have
used fdisk to create the following partitions:
/dev/sda1 (Linux ext2, at least 400MB)
/dev/sda2 (Linux swap, recommended 256MB)
This script will DESTROY ALL EXISTING DATA on /dev/sda1
Please double check that the device on /dev/sda1 is the correct device.
By typing ok, you agree to assume all liabilities and risks
associated with running this installer.
If everything looks good, type 'ok' to continue: ok
Connecting to jeff.doozan.com (50.116.34.13:80)
Connecting to projects.doozan.com (50.116.34.13:80)
Installing Bootloader
# checking for /usr/sbin/nandwrite...
# checking for /usr/sbin/nanddump...
# checking for /usr/sbin/flash_erase...
# checking for /usr/sbin/fw_printenv...
# checking for /etc/fw_env.config...
# Validating existing uBoot...
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x00000000 and ending at 0x00080000...
Connecting to jeff.doozan.com (50.116.34.13:80)
Connecting to projects.doozan.com (50.116.34.13:80)
## Unknown uBoot detected on mtd0: fe82e990a551e26c4be919f05ac873a5
##
## The installer could not detect the version of your current uBoot
## This may happen if you have installed a different uBoot on
## /dev/mtd0 or if you have bad blocks on /dev/mtd0
##
## If you have bad blocks on mtd0, you should not try to install uBoot.
##
## Installation cancelled.
Filesystem label=
OS type: Linux
Block size=1024 (log=0)
Fragment size=1024 (log=0)
125488 inodes, 501084 blocks
25054 blocks (5%) reserved for the super user
First data block=1
Maximum filesystem blocks=524288
62 block groups
8192 blocks per group, 8192 fragments per group
2024 inodes per group
Superblock backups stored on blocks:
8193, 24577, 40961, 57345, 73729, 204801, 221185, 401409
./dockstar.debian-squeeze.sh: line 298: /sbin/mkswap: not found
# Starting debootstrap installation
I: Retrieving Release
I: Retrieving Packages
I: Validating Packages
I: Resolving dependencies of required packages...
I: Resolving dependencies of base packages...
I: Found additional required dependencies: insserv libbz2-1.0 libdb4.8 libslang2
I: Found additional base dependencies: adduser cpio debian-archive-keyring devio gnupg gpgv initramfs-tools klibc-utils libbsd0 libcap2 libedit2 libgssapi-krb5-2 libk5crypto3 libkeyutils1 libklibc libkrb5-3 libkrb5support0 libncursesw5 libreadline6 libssl0.9.8 libudev0 libusb-0.1-4 libuuid-perl libwrap0 linux-base linux-image-2.6.32-5-kirkwood openssh-blacklist openssh-client procps readline-common vim-common
I: Checking component main on http://ftp.de.debian.org/debian...
I: Retrieving libacl1
I: Validating libacl1
I: Retrieving adduser
I: Validating adduser
I: Retrieving apt
I: Validating apt
I: Retrieving libattr1
I: Validating libattr1
I: Retrieving base-files
I: Validating base-files
I: Retrieving base-passwd
I: Validating base-passwd
I: Retrieving bash
I: Validating bash
I: Retrieving libbz2-1.0
I: Validating libbz2-1.0
I: Retrieving coreutils
I: Validating coreutils
I: Retrieving cpio
I: Validating cpio
I: Retrieving dash
I: Validating dash
I: Retrieving libdb4.8
I: Validating libdb4.8
I: Retrieving debconf-i18n
I: Validating debconf-i18n
I: Retrieving debconf
I: Validating debconf
I: Retrieving debian-archive-keyring
I: Validating debian-archive-keyring
I: Retrieving debianutils
I: Validating debianutils
I: Retrieving devio
I: Validating devio
I: Retrieving dhcpcd
I: Validating dhcpcd
I: Retrieving diffutils
I: Validating diffutils
I: Retrieving dpkg
I: Validating dpkg
I: Retrieving e2fslibs
I: Validating e2fslibs
I: Retrieving e2fsprogs
I: Validating e2fsprogs
I: Retrieving libcomerr2
I: Validating libcomerr2
I: Retrieving libss2
I: Validating libss2
I: Retrieving libc-bin
I: Validating libc-bin
I: Retrieving libc6
I: Validating libc6
I: Retrieving findutils
I: Validating findutils
I: Retrieving flash-kernel
I: Validating flash-kernel
I: Retrieving gcc-4.4-base
I: Validating gcc-4.4-base
I: Retrieving libgcc1
I: Validating libgcc1
I: Retrieving libstdc++6
I: Validating libstdc++6
I: Retrieving gnupg
I: Validating gnupg
I: Retrieving gpgv
I: Validating gpgv
I: Retrieving grep
I: Validating grep
I: Retrieving gzip
I: Validating gzip
I: Retrieving hostname
I: Validating hostname
I: Retrieving ifupdown
I: Validating ifupdown
I: Retrieving initramfs-tools
I: Validating initramfs-tools
I: Retrieving insserv
I: Validating insserv
I: Retrieving iproute
I: Validating iproute
I: Retrieving iputils-ping
I: Validating iputils-ping
I: Retrieving libkeyutils1
I: Validating libkeyutils1
I: Retrieving klibc-utils
I: Validating klibc-utils
I: Retrieving libklibc
I: Validating libklibc
I: Retrieving libgssapi-krb5-2
I: Validating libgssapi-krb5-2
I: Retrieving libk5crypto3
I: Validating libk5crypto3
I: Retrieving libkrb5-3
I: Validating libkrb5-3
I: Retrieving libkrb5support0
I: Validating libkrb5support0
I: Retrieving linux-base
I: Validating linux-base
I: Retrieving linux-image-2.6.32-5-kirkwood
I: Validating linux-image-2.6.32-5-kirkwood
I: Retrieving linux-image-2.6-kirkwood
I: Validating linux-image-2.6-kirkwood
I: Retrieving lsb-base
I: Validating lsb-base
I: Retrieving libbsd0
I: Validating libbsd0
I: Retrieving libcap2
I: Validating libcap2
I: Retrieving libedit2
I: Validating libedit2
I: Retrieving liblocale-gettext-perl
I: Validating liblocale-gettext-perl
I: Retrieving libselinux1
I: Validating libselinux1
I: Retrieving libsepol1
I: Validating libsepol1
I: Retrieving libtext-charwidth-perl
I: Validating libtext-charwidth-perl
I: Retrieving libtext-iconv-perl
I: Validating libtext-iconv-perl
I: Retrieving libtext-wrapi18n-perl
I: Validating libtext-wrapi18n-perl
I: Retrieving libusb-0.1-4
I: Validating libusb-0.1-4
I: Retrieving libuuid-perl
I: Validating libuuid-perl
I: Retrieving mawk
I: Validating mawk
I: Retrieving module-init-tools
I: Validating module-init-tools
I: Retrieving libncurses5
I: Validating libncurses5
I: Retrieving libncursesw5
I: Validating libncursesw5
I: Retrieving ncurses-base
I: Validating ncurses-base
I: Retrieving ncurses-bin
I: Validating ncurses-bin
I: Retrieving net-tools
I: Validating net-tools
I: Retrieving netbase
I: Validating netbase
I: Retrieving ntpdate
I: Validating ntpdate
I: Retrieving openssh-blacklist
I: Validating openssh-blacklist
I: Retrieving openssh-client
I: Validating openssh-client
I: Retrieving openssh-server
I: Validating openssh-server
I: Retrieving libssl0.9.8
I: Validating libssl0.9.8
I: Retrieving libpam-modules
I: Validating libpam-modules
I: Retrieving libpam-runtime
I: Validating libpam-runtime
I: Retrieving libpam0g
I: Validating libpam0g
I: Retrieving perl-base
I: Validating perl-base
I: Retrieving procps
I: Validating procps
I: Retrieving libreadline6
I: Validating libreadline6
I: Retrieving readline-common
I: Validating readline-common
I: Retrieving sed
I: Validating sed
I: Retrieving sensible-utils
I: Validating sensible-utils
I: Retrieving login
I: Validating login
I: Retrieving passwd
I: Validating passwd
I: Retrieving libslang2
I: Validating libslang2
I: Retrieving initscripts
I: Validating initscripts
I: Retrieving sysv-rc
I: Validating sysv-rc
I: Retrieving sysvinit-utils
I: Validating sysvinit-utils
I: Retrieving sysvinit
I: Validating sysvinit
I: Retrieving tar
I: Validating tar
I: Retrieving libwrap0
I: Validating libwrap0
I: Retrieving libudev0
I: Validating libudev0
I: Retrieving bsdutils
I: Validating bsdutils
I: Retrieving libblkid1
I: Validating libblkid1
I: Retrieving libuuid1
I: Validating libuuid1
I: Retrieving mount
I: Validating mount
I: Retrieving liblzma2
I: Validating liblzma2
I: Retrieving tzdata
I: Validating tzdata
I: Retrieving uboot-envtools
I: Validating uboot-envtools
I: Retrieving uboot-mkimage
I: Validating uboot-mkimage
I: Retrieving udev
I: Validating udev
I: Retrieving util-linux
I: Validating util-linux
I: Retrieving vim-common
I: Validating vim-common
I: Retrieving vim-tiny
I: Validating vim-tiny
I: Retrieving wget
I: Validating wget
I: Retrieving xz-utils
I: Validating xz-utils
I: Retrieving zlib1g
I: Validating zlib1g
I: Chosen extractor for .deb packages: ar
I: Extracting libacl1...
E: Unknown compression type for in .//var/cache/apt/archives/libacl1_2.2.49-4_armel.deb
debootstrap failed.
See /tmp/debian/debootstrap/debootstrap.log for more information.
|
Re: Unknown compression type for in .//var/cache/apt/archives/libacl1_2.2.49-4_armel.deb June 01, 2013 12:27AM |
Registered: 10 years ago Posts: 8 |
mount -o remount,rw / rm /usr/sbin/debootstrap rm -r /usr/share/debootstrap mount -o remount,ro /
|
Re: Unknown compression type for in .//var/cache/apt/archives/libacl1_2.2.49-4_armel.deb June 01, 2013 03:22AM |
Admin Registered: 13 years ago Posts: 18,558 |
|
Re: Unknown compression type for in .//var/cache/apt/archives/libacl1_2.2.49-4_armel.deb June 01, 2013 03:32AM |
Registered: 10 years ago Posts: 8 |
|
Re: Unknown compression type for in .//var/cache/apt/archives/libacl1_2.2.49-4_armel.deb June 01, 2013 11:15AM |
Registered: 10 years ago Posts: 8 |
ECC: 8 uncorrectable bitflip(s) at offset 0x0014f000 ECC: 8 uncorrectable bitflip(s) at offset 0x0014f800 ECC: 8 uncorrectable bitflip(s) at offset 0x00150000 ECC: 8 uncorrectable bitflip(s) at offset 0x00150800 ECC: 8 uncorrectable bitflip(s) at offset 0x00151000 ECC: 8 uncorrectable bitflip(s) at offset 0x00151800 ECC: 8 uncorrectable bitflip(s) at offset 0x00152000 ECC: 8 uncorrectable bitflip(s) at offset 0x00152800 ECC: 8 uncorrectable bitflip(s) at offset 0x00153000 ECC: 8 uncorrectable bitflip(s) at offset 0x00153800 ECC: 8 uncorrectable bitflip(s) at offset 0x00154000 ECC: 8 uncorrectable bitflip(s) at offset 0x00154800 ECC: 8 uncorrectable bitflip(s) at offset 0x00155000 ECC: 8 uncorrectable bitflip(s) at offset 0x00155800 ECC: 8 uncorrectable bitflip(s) at offset 0x00156000 ECC: 8 uncorrectable bitflip(s) at offset 0x00156800 ECC: 8 uncorrectable bitflip(s) at offset 0x00157000 ECC: 8 uncorrectable bitflip(s) at offset 0x00157800 ECC: 8 uncorrectable bitflip(s) at offset 0x00158000 ECC: 8 uncorrectable bitflip(s) at offset 0x00158800 ECC: 8 uncorrectable bitflip(s) at offset 0x00159000 ECC: 8 uncorrectable bitflip(s) at offset 0x00159800 ECC: 8 uncorrectable bitflip(s) at offset 0x0015a000 ECC: 8 uncorrectable bitflip(s) at offset 0x0015a800 ECC: 8 uncorrectable bitflip(s) at offset 0x0015b000 ECC: 8 uncorrectable bitflip(s) at offset 0x0015b800 ECC: 8 uncorrectable bitflip(s) at offset 0x0015c000 ECC: 8 uncorrectable bitflip(s) at offset 0x0015c800 ECC: 8 uncorrectable bitflip(s) at offset 0x0015d000 ECC: 8 uncorrectable bitflip(s) at offset 0x0015d800 ECC: 8 uncorrectable bitflip(s) at offset 0x0015e000 ECC: 8 uncorrectable bitflip(s) at offset 0x0015e800 ECC: 8 uncorrectable bitflip(s) at offset 0x0015f000 ECC: 8 uncorrectable bitflip(s) at offset 0x0015f800 # Erasing mtd1 @ 0x500000 for 17 erase blocks (kernel location) Erase Total 17 Units Performing Flash Erase of length 131072 at offset 0x700000 done # Erasing mtd1 @ 0xB00000 for 17 erase blocks (2nd kernel location) Erase Total 17 Units Performing Flash Erase of length 131072 at offset 0xd00000 done # Flashing Kernel... # - @ 0x500000 Writing data to block 40 at offset 0x500000 Writing data to block 41 at offset 0x520000 Writing data to block 42 at offset 0x540000 Writing data to block 43 at offset 0x560000 Writing data to block 44 at offset 0x580000 Writing data to block 45 at offset 0x5a0000 Writing data to block 46 at offset 0x5c0000 Writing data to block 47 at offset 0x5e0000 Writing data to block 48 at offset 0x600000 Writing data to block 49 at offset 0x620000 Writing data to block 50 at offset 0x640000 Writing data to block 51 at offset 0x660000 Writing data to block 52 at offset 0x680000 Writing data to block 53 at offset 0x6a0000 Writing data to block 54 at offset 0x6c0000 Writing data to block 55 at offset 0x6e0000 Writing data to block 56 at offset 0x700000 Writing data to block 57 at offset 0x720000 # - @ 0xB00000 Writing data to block 88 at offset 0xb00000 Writing data to block 89 at offset 0xb20000 Writing data to block 90 at offset 0xb40000 Writing data to block 91 at offset 0xb60000 Writing data to block 92 at offset 0xb80000 Writing data to block 93 at offset 0xba0000 Writing data to block 94 at offset 0xbc0000 Writing data to block 95 at offset 0xbe0000 Writing data to block 96 at offset 0xc00000 Writing data to block 97 at offset 0xc20000 Writing data to block 98 at offset 0xc40000 Writing data to block 99 at offset 0xc60000 Writing data to block 100 at offset 0xc80000 Writing data to block 101 at offset 0xca0000 Writing data to block 102 at offset 0xcc0000 Writing data to block 103 at offset 0xce0000 Writing data to block 104 at offset 0xd00000 Writing data to block 105 at offset 0xd20000 # Done Flashing Kernel # NEW uBoot Parameters # = bootargs_usb : root=/dev/sda1 ubi.mtd=2,512 rootfstype=ext2 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=128M poweroutage=yes rootwait # = load_custom_nand : nboot 60500000 0 500000 # = rootfs : /dev/sda1 # = root fs type : ext2 # # Setting up uboot parameters # # Checking uboot parameters... # = bootargs_stock : root=ubi0:rootfs ubi.mtd=2,512 rootfstype=ubifs console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=128M poweroutage=yes # = bootargs : root=/dev/sda1 ubi.mtd=2,512 rootfstype=ext2 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=128M poweroutage=yes rootwait # = load_custom_nand : nboot 60500000 0 500000 # = boot_custom : run load_custom_nand boot || run load_custom_nand2 boot ############################# ## Looks good! # Sync ... # Unmount # Reboot to enter into Arch Linux ARM /tmp # reboot
|
Re: Unknown compression type for in .//var/cache/apt/archives/libacl1_2.2.49-4_armel.deb June 01, 2013 11:56PM |
Registered: 10 years ago Posts: 8 |
Setup memory, testing
Reading NAND, Image 0
Hdr len: 0x0001C030
Hdr CRC: 0x39F6D832
OK
U-Boot 1.1.2 (Jul 29 2010 - 19:36:07)
U-Boot code: 60D00000 -> 60D1C030 BSS: -> 60D21800
RAM Configuration:
Bank #0: 60000000 128 MB
SRAM Configuration:
64KB at 0x50000000
NAND:128 MiB
In: serial
Out: serial
Err: serial
Setting Linux mem= boot arg value
Hit any key to stop autoboot: 0
Loading from device 0: 128MiB 3,3V 8-bit (offset 0x500000)
-- Using 1bit ECC style encoding
Image Name: Linux-2.6.31.6_SMP_820
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2345664 Bytes = 2.2 MB
Load Address: 60008000
Entry Point: 60008000
## Booting image at 60500000 ...
Image Name: Linux-2.6.31.6_SMP_820
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2345664 Bytes = 2.2 MB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux.............................................................................................................................................. done, booting the kernel.
[ 0.000000] Linux version 2.6.31.6_SMP_820 (root@hunchback) (gcc version 4.7.0 20120505 (prerelease) (GCC) ) #7 SMP Thu Jun 14 20:31:06 CDT 2012
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Oxsemi NAS
[ 0.000000] 1 memory region
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: root=/dev/sda1 ubi.mtd=2,512 rootfstype=ext2 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 rootwait mem=128M poweroutage=yes
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 125112KB available (4012K code, 316K data, 144K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:96
[ 0.000000] OX820_RPS_init_irq: interrupts 64 to 96
[ 0.010000] Console: colour dummy device 80x30
[ 0.010000] console [ttyS0] enabled
[ 0.020000] Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736)
[ 0.260000] Security Framework initialized
[ 0.260000] Mount-cache hash table entries: 512
[ 0.270000] CPU: Testing write buffer coherency: ok
[ 0.270000] Calibrating local timer... 349.99MHz.
[ 0.340000] CPU1: Booted secondary processor
[ 0.440000] Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736)
[ 0.670000] Brought up 2 CPUs
[ 0.680000] SMP: Total of 2 processors activated (558.69 BogoMIPS).
[ 0.690000] tmpfs: No value for mount option 'mode'
[ 0.690000] devtmpfs: initialized
[ 0.700000] NET: Registered protocol family 16
[ 0.700000] Number of DMA channels = 4, version = 4
[ 0.710000] Reserving a DMA channel for DirectRAID
[ 0.710000] Allocating 389 SRAM generic DMA descriptors
[ 1.220000] PCIeA version/deviceID 082510b5
[ 1.220000] PCIeB version/deviceID 082510b5
[ 4.230000] ox820_pci_preinit() PCIEA link up timeout (00001014)
[ 7.240000] ox820_pci_preinit() PCIEB link up timeout (00001014)
[ 7.240000] ox820_pcie_setup_resources() Enabling PCIe Pre-Emphasis
[ 7.250000] ox820_pciea_setup_resources() resource c781b140
[ 7.250000] ox820_pciea_setup_resources() io: 0x4be00000 - 0x4befffff
[ 7.260000] ox820_pciea_setup_resources() non-pre: 0x48000000 - 0x49ffffff
[ 7.270000] ox820_pciea_setup_resources() pre: 0x4a000000 - 0x4bdfffff
[ 7.270000] PCI: bus0: Fast back to back transfers enabled
[ 7.280000] PCI: bus1: Fast back to back transfers enabled
[ 7.300000] bio: create slab <bio-0> at 0
[ 7.310000] SCSI subsystem initialized
[ 7.310000] usbcore: registered new interface driver usbfs
[ 7.320000] usbcore: registered new interface driver hub
[ 7.320000] usbcore: registered new device driver usb
[ 7.350000] NET: Registered protocol family 2
[ 7.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 7.360000] Switched to NOHz mode on CPU #0
[ 7.360000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 7.360000] Switched to NOHz mode on CPU #1
[ 7.370000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 7.380000] TCP: Hash tables configured (established 4096 bind 4096)
[ 7.380000] TCP reno registered
[ 7.390000] NET: Registered protocol family 1
[ 7.390000] Create fragment cache
[ 7.420000] fuse init (API version 7.12)
[ 7.420000] msgmni has been set to 244
[ 7.430000] alg: No test for stdrng (krng)
[ 7.430000] io scheduler noop registered
[ 7.440000] io scheduler anticipatory registered
[ 7.440000] io scheduler deadline registered
[ 7.440000] io scheduler cfq registered (default)
[ 7.470000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 7.480000] serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
[ 7.490000] brd: module loaded
[ 7.500000] loop: module loaded
[ 7.510000] ox820sata: OX820 sata core.
[ 7.510000] scsi0 : oxnassata
[ 7.520000] scsi1 : oxnassata
[ 7.520000] ata1: SATA max UDMA/133 irq 50
[ 7.520000] ata2: SATA max UDMA/133 irq 50
[ 7.530000] ox820sata: reseting SATA core
[ 7.890000] ata1: SATA link down (SStatus 0 SControl 300)
[ 7.890000] ox820sata: reseting SATA core
[ 8.250000] ata2: SATA link down (SStatus 0 SControl 300)
[ 8.250000] tun: Universal TUN/TAP device driver, 1.6
[ 8.260000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 8.260000] NAND: Page read time 40ms
[ 8.270000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[ 8.280000] Scanning device for bad blocks
[ 8.340000] Bad eraseblock 820 at 0x000006680000
[ 8.360000] Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit":
[ 8.360000] 0x000000000000-0x000000e00000 : "boot"
[ 8.370000] 0x000000e00000-0x000008000000 : "rootfs"
[ 8.370000] UBI: attaching mtd2 to ubi0
[ 8.380000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 8.380000] UBI: logical eraseblock size: 129024 bytes
[ 8.390000] UBI: smallest flash I/O unit: 2048
[ 8.390000] UBI: sub-page size: 512
[ 8.400000] UBI: VID header offset: 512 (aligned 512)
[ 8.400000] UBI: data offset: 2048
[ 8.820000] UBI: attached mtd2 to ubi0
[ 8.820000] UBI: MTD device name: "rootfs"
[ 8.820000] UBI: MTD device size: 114 MiB
[ 8.830000] UBI: number of good PEBs: 911
[ 8.830000] UBI: number of bad PEBs: 1
[ 8.840000] UBI: max. allowed volumes: 128
[ 8.840000] UBI: wear-leveling threshold: 4096
[ 8.850000] UBI: number of internal volumes: 1
[ 8.850000] UBI: number of user volumes: 1
[ 8.860000] UBI: available PEBs: 0
[ 8.860000] UBI: total number of reserved PEBs: 911
[ 8.870000] UBI: number of PEBs reserved for bad PEB handling: 9
[ 8.870000] UBI: max/mean erase counter: 2/0
[ 8.880000] UBI: image sequence number: 0
[ 8.880000] UBI: background thread "ubi_bgt0d" started, PID 312
[ 8.880000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.880000] oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
[ 8.880000] oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1
[ 8.920000] oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000
[ 8.940000] oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00
[ 8.940000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.950000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.950000] usb usb1: Product: OXNAS EHCI Host Controller
[ 8.960000] usb usb1: Manufacturer: Linux 2.6.31.6_SMP_820 ehci_hcd
[ 8.970000] usb usb1: SerialNumber: usb
[ 8.970000] usb usb1: configuration #1 chosen from 1 choice
[ 8.980000] hub 1-0:1.0: USB hub found
[ 8.980000] hub 1-0:1.0: 2 ports detected
[ 8.990000] Initializing USB Mass Storage driver...
[ 8.990000] usbcore: registered new interface driver usb-storage
[ 9.000000] USB Mass Storage support registered.
[ 9.000000] usbcore: registered new interface driver libusual
[ 9.010000] mice: PS/2 mouse device common for all mice
[ 9.010000] usbcore: registered new interface driver hiddev
[ 9.020000] usbcore: registered new interface driver usbhid
[ 9.030000] usbhid: v2.6:USB HID core driver
[ 9.030000] TCP cubic registered
[ 9.030000] NET: Registered protocol family 10
[ 9.040000] lo: Disabled Privacy Extensions
[ 9.040000] NET: Registered protocol family 17
[ 9.050000] RPC: Registered udp transport module.
[ 9.050000] RPC: Registered tcp transport module.
[ 9.060000] Waiting for root device /dev/sda1...
[ 9.300000] usb 1-1: new high speed USB device using oxnas-ehci and address 2
[ 9.450000] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 9.450000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 9.460000] usb 1-1: Product: USB2.0 Hub
[ 9.470000] usb 1-1: configuration #1 chosen from 1 choice
[ 9.470000] hub 1-1:1.0: USB hub found
[ 9.480000] hub 1-1:1.0: 4 ports detected
[ 9.760000] usb 1-1.4: new high speed USB device using oxnas-ehci and address 3
[ 9.880000] usb 1-1.4: New USB device found, idVendor=05e3, idProduct=0723
[ 9.890000] usb 1-1.4: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[ 9.890000] usb 1-1.4: Product: USB Storage
[ 9.900000] usb 1-1.4: Manufacturer: Generic
[ 9.900000] usb 1-1.4: SerialNumber: 000000009451
[ 9.910000] usb 1-1.4: configuration #1 chosen from 1 choice
[ 9.920000] scsi2 : SCSI emulation for USB Mass Storage devices
[ 14.920000] scsi 2:0:0:0: Direct-Access Generic STORAGE DEVICE 9451 PQ: 0 ANSI: 0
[ 15.220000] sd 2:0:0:0: [sda] 3862528 512-byte logical blocks: (1.97 GB/1.84 GiB)
[ 15.230000] sd 2:0:0:0: [sda] Write Protect is off
[ 15.230000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 15.240000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 15.250000] sda: sda1
[ 15.260000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 15.260000] sd 2:0:0:0: [sda] Attached SCSI removable disk
[ 15.330000] EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
[ 15.340000] VFS: Mounted root (ext2 filesystem) on device 8:1.
[ 15.350000] devtmpfs: mounted
[ 15.350000] Freeing init memory: 144K
INIT: version 2.88 booting
HOSTNAME= is deprecated. See rc.conf(5) and hostname(5) for details.
> Arch Linux ARM
> http://archlinuxarm.org/
------------------------------
:: Mounting root read-only [DONE]
:: Setting hostname: alarm [DONE]
HARDWARECLOCK= is deprecated. See rc.conf(5) and hwclock(8) for details.
:: Adjusting system time and setting kernel time zone [BUSY] TIMEZONE= is deprecated. See rc.conf(5) for details.
[DONE]
:: Starting udev daemon [BUSY] [ 18.630000] <30>systemd-udevd[394]: starting version 196
[DONE]
:: Triggering udev uevents [DONE]
:: Loading user-specified modules [BUSY] MODULES= is deprecated. See rc.conf(5) and modules-load.d(5) for details.
[ 19.130000] Probing for Synopsis GMAC, unit 0
[ 19.140000] eth0: Tuning GMAC 0 RGMII timings
[ 19.140000] eth0: PHY is Realtek RTL8211D, type 0x001cc914
[ 19.160000] eth0: GMAC ver = 53, vendor ver = 18 at 0xed400000, IRQ 40
[ 19.160000] eth0: Found PHY at address 3, type 0x001cc914 -> 10/100/1000
[ 19.170000] eth0: Ethernet addr: 00:30:e0:00:00:00
[ 19.170000] probe() eth0: Leon x2 clock
[DONE]
:: Waiting for udev uevents to be processed [DONE]
:: Configuring virtual consoles [DONE]
:: Bringing up loopback interface [DONE]
:: Checking filesystems [DONE]
:: Remounting root and API filesystems [BUSY] [ 19.870000] EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
[DONE]
:: Mounting local filesystems [DONE]
:: Activating swap [DONE]
:: Configuring time zone [DONE]
:: Initializing random seed [DONE]
:: Removing leftover files [DONE]
NIT: Entering runlevel: 3 [DONE]
mount: mount point /proc/sys/fs/binfmt_misc does not exist
:: Setting MAC address [BUSY] [ 20.930000] Turning off blinking LED.
ORANGE
AMBER
GREEN
[ 21.340000] eth0: PHY is Realtek RTL8211D, type 0x001cc914
[ 21.340000] CoPro offload is active on eth0
[ 21.350000] Alloc'ing ARM descs 8192 bytes
[ 21.350000] Alloc'ing CoPro parameters 36 bytes
[ 21.360000] gmac gmac.0: firmware: requesting gmac_copro_firmware
[ 21.380000] CoPro: Programming start address as 0xd000e000
[ 21.480000] eth0: Resetting GMAC
[ 21.480000] eth0: GMAC reset complete
[ 21.490000] eth0: Setting Rx flow control thresholds for LAN port
[ 22.050000] eth0: PHY is Realtek RTL8211D, type 0x001cc914
[ 22.550000] eth0: link down
[ 24.510000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[DONE]
:: Starting Syslog-NG [DONE]
:: Starting network [BUSY]
[DONE]
:: Mounting network filesystems [DONE]
:: Starting crond daemon [DONE]
:: Starting Secure Shell Daemon [DONE]
:: Starting OpenNTPD [DONE]
Arch Linux 2.6.31.6_SMP_820 (ttyS0)
alarm login:
Arch Linux 2.6.31.6_SMP_820 (ttyS0)
alarm login: root
Password:
Last login: Thu Jun 14 18:55:42 from sss7
[root@alarm ~]# ls
[root@alarm ~]#
[root@alarm ~]#
[root@alarm ~]# df -h
Filesystem Size Used Avail Use% Mounted on
rootfs 1.9G 588M 1.2G 34% /
/dev/root 1.9G 588M 1.2G 34% /
devtmpfs 62M 0 62M 0% /dev
run 62M 168K 62M 1% /run
shm 62M 0 62M 0% /dev/shm
[root@alarm ~]# ifconfig
eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 00:25:31:01:4b:e7 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 40
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 16436
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 20 bytes 1412 (1.3 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 20 bytes 1412 (1.3 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[root@alarm ~]# uname -a
Linux alarm 2.6.31.6_SMP_820 #7 SMP Thu Jun 14 20:31:06 CDT 2012 armv6l GNU/Linux
[root@alarm ~]#
|
Re: Unknown compression type for in .//var/cache/apt/archives/libacl1_2.2.49-4_armel.deb June 02, 2013 12:13AM |
Admin Registered: 13 years ago Posts: 18,558 |
|
Re: Unknown compression type for in .//var/cache/apt/archives/libacl1_2.2.49-4_armel.deb June 02, 2013 12:59AM |
Registered: 10 years ago Posts: 8 |
[ 246.360000] eth0: PHY is Realtek RTL8211D, type 0x001cc914 [ 246.370000] eth0: Resetting GMAC [ 246.370000] eth0: GMAC reset complete [ 246.380000] eth0: Setting Rx flow control thresholds for LAN port [ 246.930000] eth0: PHY is Realtek RTL8211D, type 0x001cc914 [ 246.950000] Attempting to set new mtu 1500 [ 246.950000] eth0: PHY is Realtek RTL8211D, type 0x001cc914 [ 246.960000] eth0: Resetting GMAC [ 246.960000] eth0: GMAC reset complete [ 246.970000] eth0: Setting Rx flow control thresholds for LAN port [ 247.530000] eth0: PHY is Realtek RTL8211D, type 0x001cc914 [ 250.030000] eth0: link up, 100Mbps, full-duplex, using pause, lpa 0x45E1 [ 250.030000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 255.560000] Attempting to set new mtu 576 [ 255.560000] eth0: PHY is Realtek RTL8211D, type 0x001cc914 [ 255.570000] eth0: Resetting GMAC [ 255.570000] eth0: GMAC reset complete [ 255.580000] eth0: Setting Rx flow control thresholds for LAN port [ 256.100000] Attempting to set new mtu 1500 [ 256.110000] eth0: PHY is Realtek RTL8211D, type 0x001cc914 [ 256.120000] eth0: Resetting GMAC [ 256.120000] eth0: GMAC reset complete [ 256.120000] eth0: Setting Rx flow control thresholds for LAN port [ 256.680000] eth0: PHY is Realtek RTL8211D, type 0x001cc914 [ 259.180000] eth0: link up, 100Mbps, full-duplex, using pause, lpa 0x45E1
|
Re: Unknown compression type for in .//var/cache/apt/archives/libacl1_2.2.49-4_armel.deb June 03, 2013 07:35PM |
Registered: 10 years ago Posts: 8 |
Dec 31 18:00:50 alarm dhcpcd[1056]: eth0: eth0: MTU restored to 1500 Dec 31 18:00:54 alarm dhcpcd[800]: eth0: carrier acquired Dec 31 18:00:54 alarm dhcpcd[800]: eth0: rebinding lease of 192.168.1.103 Dec 31 18:00:54 alarm dhcpcd[800]: eth0: acknowledged 192.168.1.103 from 192.168 .1.1 `\377' Dec 31 18:00:54 alarm dhcpcd[800]: eth0: leased 192.168.1.103 for 7200 seconds Dec 31 18:00:54 alarm dhcpcd[1081]: eth0: eth0: MTU set to 576 Dec 31 18:00:55 alarm dhcpcd[800]: eth0: carrier lost Dec 31 18:00:55 alarm dhcpcd[1100]: eth0: eth0: MTU restored to 1500 Dec 31 18:00:58 alarm dhcpcd[800]: eth0: carrier acquired Dec 31 18:00:58 alarm dhcpcd[800]: eth0: rebinding lease of 192.168.1.103 Dec 31 18:00:58 alarm dhcpcd[800]: eth0: acknowledged 192.168.1.103 from 192.168 .1.1 `\377' Dec 31 18:00:58 alarm dhcpcd[800]: eth0: leased 192.168.1.103 for 7200 seconds Dec 31 18:00:58 alarm dhcpcd[1117]: eth0: eth0: MTU set to 576 Dec 31 18:00:59 alarm dhcpcd[800]: eth0: carrier lost Dec 31 18:00:59 alarm dhcpcd[1136]: eth0: eth0: MTU restored to 1500 Dec 31 18:01:02 alarm dhcpcd[800]: eth0: carrier acquired Dec 31 18:01:02 alarm dhcpcd[800]: eth0: rebinding lease of 192.168.1.103 Dec 31 18:01:02 alarm dhcpcd[800]: eth0: acknowledged 192.168.1.103 from 192.168 .1.1 `\377' Dec 31 18:01:02 alarm dhcpcd[800]: eth0: leased 192.168.1.103 for 7200 seconds Dec 31 18:01:02 alarm dhcpcd[1153]: eth0: eth0: MTU set to 576 Dec 31 18:01:03 alarm dhcpcd[800]: eth0: carrier lost Dec 31 18:01:03 alarm dhcpcd[1172]: eth0: eth0: MTU restored to 1500
[ 1716.580000] eth0: link up, 100Mbps, full-duplex, using pause, lpa 0x45E1 [ 1716.580000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 1716.970000] Attempting to set new mtu 576 [ 1716.970000] eth0: PHY is Realtek RTL8211D, type 0x001cc914 [ 1716.980000] eth0: Resetting GMAC [ 1716.980000] eth0: GMAC reset complete [ 1716.990000] eth0: Setting Rx flow control thresholds for LAN port [ 1717.540000] eth0: PHY is Realtek RTL8211D, type 0x001cc914 [ 1717.690000] Attempting to set new mtu 1500 [ 1717.700000] eth0: PHY is Realtek RTL8211D, type 0x001cc914 [ 1717.710000] eth0: Resetting GMAC [ 1717.710000] eth0: GMAC reset complete [ 1717.710000] eth0: Setting Rx flow control thresholds for LAN port [ 1718.270000] eth0: PHY is Realtek RTL8211D, type 0x001cc914 [ 1720.770000] eth0: link up, 100Mbps, full-duplex, using pause, lpa 0x45E1 [ 1720.770000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 1721.160000] Attempting to set new mtu 576 [ 1721.160000] eth0: PHY is Realtek RTL8211D, type 0x001cc914 [ 1721.170000] eth0: Resetting GMAC [ 1721.170000] eth0: GMAC reset complete [ 1721.180000] eth0: Setting Rx flow control thresholds for LAN port [ 1721.740000] eth0: PHY is Realtek RTL8211D, type 0x001cc914