Arch Linux on Lenovo ix2 NAS stuck at Starting kernel

hello, i tried to install arch linux on my lenovo iomega ix2 nas, but i failed every time because it gets stuck at the point where it just says starting kernel ... . I have also read the other posts, but unfortunately nothing has helped. Can someone please help me.


| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 1 0]: Enable DMA mode (5)
Device 1 @ 0 1:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
.
....
......
............
.
.........................
.........................
........................
.
.........................
.........................
.........................
.........................
.........................
.........................
.........................
.........................
.........................
.........................
.........................
.........................
.........................
..............

4612216 bytes read
.
....
......
............
.
........................
.
.........................
........................
.
.........................
.........................
.........................
........................
.
.........................
.........................
.........................
.........................
.........................
.........................
.........................
........................
.
.........................
.........................
.........................
.........................
.........................
.........................
.........................
........................
.
.........................
.....................

6788126 bytes read
## Booting image at 01000000 ...
Image Name: Linux-4.4.176-1-ARCH
Created: 2019-02-23 19:03:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4612152 Bytes = 4.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 08004000 ...
Image Name: Arch Linux ARM initrd
Created: 2025-02-28 20:03:20 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6788062 Bytes = 6.5 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK

Starting kernel ...

Jan_Grz1,

Arch Linux ARM has stopped support for the Kirkwod SoCs. Why not switch to Debian? is there any particular reason you've chosen to run Arch?

Here is how to boot Debian rootfs with stock u-boot.

https://forum.doozan.com/read.php?2,102054,105374#msg-105374

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi,

Thank you very much for your reply. No there is no specific reason why I tried to use arch linux. I will try Debian, thank you very much

bodhi,

so i tried it according to the instructions, but i still get an error. I can't get any further.


Marvell>>
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found

** Unable to read "/uImage" from usb 0:1 **

** Unable to read "/uInitrd" from usb 0:1 **
## Booting image at 01000000 ...
Bad Magic Number

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)

Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 0:1 **
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 0:1 **
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 1:1 **
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 1:1 **
## Booting image at 01000000 ...
Bad Magic Number

Jan_Grz1,

Your envs are incorrect.

Power up, interrupt u-boot countdown on serial console, enter the setenvs command as stated in the instruction, and then

printenv
boot

And post the entire serial console log here.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi,

__  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** ix2-spi ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash:  1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
  Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0                     Firm: 01.01A01 Ser#:      WD-WCC6Y4VEC00F
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
  Device 1 @ 0 1:
Model: HGST HTS721010A9E630                     Firm: JB0OA3T0 Ser#:       JR1000D33KPNWE
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv usb_boot 'mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000'
Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
Marvell>> setenv bootcmd 'usb reset; run usb_bootcmd; usb stop; reset'
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
console=console=ttyS0,115200
bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)
kernelimage=zImage
initrdimage=mfginitrd
mfgmodel=ix2
preroot_ver=0.0.2
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; bootm 0x40000 0x900000;
uboot_ver=0.0.8
serial_number=5563Y01001G4320083EJ0D1
serialNo=SM10G7863443400111
modelname=SM10G78634
fw_ver=4.1.102.29716
serialno=0,01iQUgmEgoSup48AcUcuhp7qoS4kj/JmiFVfPP7pDVHIznMMjOVecBwbxJkWn0AOOH,SM10G7863443400111,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX2/1.1.0/download_runin.sh
pre_path_conf=IX2/1.1.0/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX2/1.1.0
serverip=192.168.32.4
ethaddr=AA:00:00:00:00:01
arcNumber=1682
bootargs_console=console=ttyS0,115200
bootargs_mtdparts=mtdparts=orion_nand:640k(u-boot)ro,16k(u-boot-env),-(iomega-firmware)ro
bootargs_root=root=LABEL=ROOT rw
memoffset_kernel=0x01000000
memoffset_initrd=0x08004000
bootargs_combine=setenv bootargs ${bootargs_console} ${bootargs_mtdparts} ${bootargs_root}
bootlinux=bootm ${memoffset_kernel} ${memoffset_initrd}
usb_load_firstdevice=ext2load usb 0:1 ${memoffset_kernel} /uImage; ext2load usb 0:1 ${memoffset_initrd} /uInitrd
usb_load=run bootargs_combine; usb reset; run usb_load_firstdevice; run bootlinux
sata_load_disk1=ext2load ide 0:1 ${memoffset_kernel} /uImage; ext2load ide 0:1 ${memoffset_initrd} /uInitrd
sata_load_disk2=ext2load ide 1:1 ${memoffset_kernel} /uImage; ext2load ide 1:1 ${memoffset_initrd} /uInitrd
sata_load=run bootargs_combine; ide reset; run sata_load_disk1; run sata_load_disk2; run bootlinux
bootargs=console=ttyS0,115200 mtdparts=orion_nand:640k(u-boot)ro,16k(u-boot-env),-(iomega-firmware)ro root=LABEL=ROOT rw
ipaddr=192.168.178.100
ethact=egiga0
load_initrd=ext2load usb 0:1 0x2100000 /uInitrd
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd
usb_boot=mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x2100000
usb_bootcmd=run usb_set_bootargs; run usb_boot
bootcmd=usb reset; run usb_bootcmd; usb stop; reset

Environment size: 3235/4091 bytes
Marvell>> boot
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
..................................................................................................................................................................................................

6235900 bytes read
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
.......................................................................................................................................................

5791271 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-6.5.7-kirkwood-tld-1
   Created:      2025-03-08  14:28:17 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    6235836 Bytes =  5.9 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
   Image Name:   initramfs-6.5.7-kirkwood-tld-1
   Created:      2023-10-31  22:53:55 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5791207 Bytes =  5.5 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

and then again stuck

=========
moderator edit: please use code tags (Formatted code button) to post log.



Edited 2 time(s). Last edit at 03/09/2025 11:40PM by bodhi.

Jan_Grz1,

Which DTB file you used to create the uImage in Step 4?

Quote
https://forum.doozan.com/read.php?2,12096
4. (Stock u-boot only) Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Skip this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time, or running kwboot with latest u-boot image).

Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box (see the folder /media/sdb1/boot/dts for the exact spelling of your Kirkwood box name).

Generate the uImage with DTB embedded inside:
cd /media/sdb1/boot
cp -a zImage-6.5.7-kirkwood-tld-1 zImage.fdt
cat dts/kirkwood-goflexnet.dtb >> zImage.fdt
mv uImage uImage.orig
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.5.7-kirkwood-tld-1 -d zImage.fdt uImage
sync

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi,

I used the kirkwood iomega_ix2_200.dtb



Edited 1 time(s). Last edit at 03/10/2025 07:12AM by Jan_Grz1.

Jan_Grz1,

The iomega_ix2_200.dtb is the wrong one.

https://wikidevi.wi-cat.ru/Iomega

Rootfs /boot/dts

-rw-r--r-- 1 root root 11964 Feb 12 10:00 kirkwood-iomega_ix2_200.dtb
-rw-r--r-- 1 root root 13124 Feb 12 10:00 kirkwood-lenovo-ix2-dl.dtb
-rw-r--r-- 1 root root 13053 Feb 12 10:00 kirkwood-lenovo-ix2-ng.dtb

Try the kirkwood-lenovo-ix2-ng.dtb.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi,

it´s not working

even if I use saveenv then it restarts all the time

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC 6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR100 0D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LAB EL=rootfs rootdelay=10 earlyprintk=serial'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv usb_boot 'mw 0x800000 0 1; run load_uimage; run load_uinitrd; b ootm 0x800000 0x2100000'
Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
Marvell>> setenv bootcmd 'usb reset; run usb_bootcmd; usb stop; reset'
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/m tdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x20 00000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
console=console=ttyS0,115200
bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7 e000(env2)
kernelimage=zImage
initrdimage=mfginitrd
mfgmodel=ix2
preroot_ver=0.0.2
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x180 0; bootm 0x40000 0x900000;
uboot_ver=0.0.8
serial_number=5563Y01001G4320083EJ0D1
serialNo=SM10G7863443400111
modelname=SM10G78634
fw_ver=4.1.102.29716
serialno=0,01iQUgmEgoSup48AcUcuhp7qoS4kj/JmiFVfPP7pDVHIznMMjOVecBwbxJkWn0AOOH,SM 10G7863443400111,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX2/1.1.0/download_runin.sh
pre_path_conf=IX2/1.1.0/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX2/1.1.0
serverip=192.168.32.4
ethaddr=AA:00:00:00:00:01
arcNumber=1682
bootargs_console=console=ttyS0,115200
bootargs_mtdparts=mtdparts=orion_nand:640k(u-boot)ro,16k(u-boot-env),-(iomega-fi rmware)ro
bootargs_root=root=LABEL=ROOT rw
memoffset_kernel=0x01000000
memoffset_initrd=0x08004000
bootargs_combine=setenv bootargs ${bootargs_console} ${bootargs_mtdparts} ${boot args_root}
bootlinux=bootm ${memoffset_kernel} ${memoffset_initrd}
usb_load_firstdevice=ext2load usb 0:1 ${memoffset_kernel} /uImage; ext2load usb 0:1 ${memoffset_initrd} /uInitrd
usb_load=run bootargs_combine; usb reset; run usb_load_firstdevice; run bootlinu x
sata_load_disk1=ext2load ide 0:1 ${memoffset_kernel} /uImage; ext2load ide 0:1 $ {memoffset_initrd} /uInitrd
sata_load_disk2=ext2load ide 1:1 ${memoffset_kernel} /uImage; ext2load ide 1:1 $ {memoffset_initrd} /uInitrd
sata_load=run bootargs_combine; ide reset; run sata_load_disk1; run sata_load_di sk2; run bootlinux
bootargs=console=ttyS0,115200 mtdparts=orion_nand:640k(u-boot)ro,16k(u-boot-env) ,-(iomega-firmware)ro root=LABEL=ROOT rw
ipaddr=192.168.178.100
ethact=egiga0
load_initrd=ext2load usb 0:1 0x2100000 /uInitrd
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdela y=10 earlyprintk=serial
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd
usb_boot=mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x21 00000
usb_bootcmd=run usb_set_bootargs; run usb_boot
bootcmd=usb reset; run usb_bootcmd; usb stop; reset

Environment size: 3235/4091 bytes
Marvell>> boot
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found

** Unable to read "/boot/uImage" from usb 0:1 **
....
.
......
............
.........................
...................................................
................................................................................ ......................
................................................................................ ................................................................................ ............................................
....
................................................................................ .......................................................................

5791271 bytes read
## Booting image at 00800000 ...
Bad Magic Number
stopping USB..

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC 6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR100 0D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found

** Unable to read "/uImage" from usb 0:1 **

** Unable to read "/uInitrd" from usb 0:1 **
## Booting image at 01000000 ...
Bad Magic Number

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC 6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR100 0D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)

Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 0:1 **
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 0:1 **
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 1:1 **
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 1:1 **
## Booting image at 01000000 ...
Bad Magic Number
Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LAB EL=rootfs rootdelay=10 earlyprintk=serial'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv usb_boot 'mw 0x800000 0 1; run load_uimage; run load_uinitrd; b ootm 0x800000 0x2100000'
Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
Marvell>> setenv bootcmd 'usb reset; run usb_bootcmd; usb stop; reset'
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/m tdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x20 00000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
console=console=ttyS0,115200
bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7 e000(env2)
kernelimage=zImage
initrdimage=mfginitrd
mfgmodel=ix2
preroot_ver=0.0.2
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x180 0; bootm 0x40000 0x900000;
uboot_ver=0.0.8
serial_number=5563Y01001G4320083EJ0D1
serialNo=SM10G7863443400111
modelname=SM10G78634
fw_ver=4.1.102.29716
serialno=0,01iQUgmEgoSup48AcUcuhp7qoS4kj/JmiFVfPP7pDVHIznMMjOVecBwbxJkWn0AOOH,SM 10G7863443400111,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX2/1.1.0/download_runin.sh
pre_path_conf=IX2/1.1.0/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX2/1.1.0
serverip=192.168.32.4
ethaddr=AA:00:00:00:00:01
arcNumber=1682
bootargs_console=console=ttyS0,115200
bootargs_mtdparts=mtdparts=orion_nand:640k(u-boot)ro,16k(u-boot-env),-(iomega-fi rmware)ro
bootargs_root=root=LABEL=ROOT rw
memoffset_kernel=0x01000000
memoffset_initrd=0x08004000
bootargs_combine=setenv bootargs ${bootargs_console} ${bootargs_mtdparts} ${boot args_root}
bootlinux=bootm ${memoffset_kernel} ${memoffset_initrd}
usb_load_firstdevice=ext2load usb 0:1 ${memoffset_kernel} /uImage; ext2load usb 0:1 ${memoffset_initrd} /uInitrd
usb_load=run bootargs_combine; usb reset; run usb_load_firstdevice; run bootlinu x
sata_load_disk1=ext2load ide 0:1 ${memoffset_kernel} /uImage; ext2load ide 0:1 $ {memoffset_initrd} /uInitrd
sata_load_disk2=ext2load ide 1:1 ${memoffset_kernel} /uImage; ext2load ide 1:1 $ {memoffset_initrd} /uInitrd
sata_load=run bootargs_combine; ide reset; run sata_load_disk1; run sata_load_di sk2; run bootlinux
ipaddr=192.168.178.100
ethact=egiga0
load_initrd=ext2load usb 0:1 0x2100000 /uInitrd
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no
bootargs=console=ttyS0,115200 mtdparts=orion_nand:640k(u-boot)ro,16k(u-boot-env) ,-(iomega-firmware)ro root=LABEL=ROOT rw
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdela y=10 earlyprintk=serial
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd
usb_boot=mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x21 00000
usb_bootcmd=run usb_set_bootargs; run usb_boot
bootcmd=usb reset; run usb_bootcmd; usb stop; reset

Environment size: 3235/4091 bytes
Marvell>> boot
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
0 Storage Device(s) found
** Bad partition 1 **
** Bad partition 1 **
## Booting image at 00800000 ...
Bad Magic Number
stopping USB..

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC 6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR100 0D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found

** Unable to read "/uImage" from usb 0:1 **

** Unable to read "/uInitrd" from usb 0:1 **
## Booting image at 01000000 ...
Bad Magic Number

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC 6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR100 0D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)

Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 0:1 **
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 0:1 **
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 1:1 **
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 1:1 **
## Booting image at 01000000 ...
Bad Magic Number
Marvell>>



Edited 1 time(s). Last edit at 03/10/2025 10:06AM by Jan_Grz1.

Jan_Grz1,

Right at the beginning, the USB drive failed to spin up. What happend after that is irrelevant.

> Marvell>> boot
> (Re)start USB...
> USB: scanning bus for devices... 2 USB Device(s)
> found
> Waiting for storage device(s) to settle before
> scanning...
> 1 Storage Device(s) found
>
> ** Unable to read "/boot/uImage" from usb 0:1 **

I guess this stock u-boot is flaky (some old Kirkwood stock u-boots are) with USB port. Try cold start (remove/attach power cord) to see if it can spin up the drive successfully.

If a cold start has the same failure, try this

- Cold start
- Interrupt u-boot countdown and do the initialization a few times.

usb start
usb start

or

usb reset
usb reset

And after the usb storage device is detected,

usb info

and then go ahead and boot like you did.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi,


__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
Marvell>>
Marvell>>
Marvell>> usb start
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
Marvell>> usb info
1: Hub, USB Revision 2.0
- Marvell EHCI
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Settings 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms

2: Mass Storage, USB Revision 2.10
- SMI Corporation USB DISK CCYYMMDDHHmmSS97
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor: 0x090c Product 0x2000 Version 17.0
Configuration: 1
- Interfaces: 1 Bus Powered 500mA
Interface: 0
- Alternate Settings 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 Out Bulk MaxPacket 512
- Endpoint 2 In Bulk MaxPacket 512

Marvell>> boot
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
0 Storage Device(s) found
** Bad partition 1 **
** Bad partition 1 **
## Booting image at 00800000 ...
Bad Magic Number
stopping USB..

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found

** Unable to read "/boot/uImage" from usb 0:1 **
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
.......................................................................................................................................................

5791271 bytes read
## Booting image at 00800000 ...
Bad Magic Number
stopping USB..

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
Marvell>>
Marvell>>

Jan_Grz1,

Power up, interrupt u-boot countdown and modify the bootcmd

setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'

And then

boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi,


__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
Marvell>>
Marvell>>
Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
Marvell>> boot
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found

** Unable to read "/boot/uImage" from usb 0:1 **
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
.......................................................................................................................................................

5791271 bytes read
## Booting image at 00800000 ...
Bad Magic Number
stopping USB..

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found

** Unable to read "/boot/uImage" from usb 0:1 **
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
.......................................................................................................................................................

5791271 bytes read
## Booting image at 00800000 ...
Bad Magic Number
stopping USB..

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
Marvell>>
Marvell>>
Marvell>>

Jan_Grz1,

> Hit any key to stop autoboot: 0

usb start
sleep 3
usb info
usb part
ext2ls usb 0:1 /boot

If all went well above

setenv bootcmd 'run usb_bootcmd; usb stop; reset'
boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi,


__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
Marvell>> usb start
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
Marvell>> sleep 3
Unknown command 'sleep' - try 'help'
Marvell>> sleep3
Unknown command 'sleep3' - try 'help'
Marvell>> sleep 3
Unknown command 'sleep' - try 'help'
Marvell>> usb info
1: Hub, USB Revision 2.0
- Marvell EHCI
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Settings 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms

2: Mass Storage, USB Revision 2.10
- SMI Corporation USB DISK CCYYMMDDHHmmSS97
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor: 0x090c Product 0x2000 Version 17.0
Configuration: 1
- Interfaces: 1 Bus Powered 500mA
Interface: 0
- Alternate Settings 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 Out Bulk MaxPacket 512
- Endpoint 2 In Bulk MaxPacket 512

Marvell>> usb part
print_part of 0

Partition Map for USB device 0 -- Partition Type: DOS

Partition Start Sector Num Sectors Type
1 2048 61847552 83

print_part of 1
## Unknown partition table

print_part of 2
## Unknown partition table

print_part of 3
## Unknown partition table

print_part of 4
## Unknown partition table
Marvell>> ext2ls usb 0:1 /boot
<DIR> 4096 .
<DIR> 4096 ..
6223880 zImage-6.5.7-kirkwood-tld-1
8557164 linux-headers-6.5.7-kirkwood-tld-1_1_armel.deb
6223880 vmlinuz-6.5.7-kirkwood-tld-1
5791271 uInitrd
5791207 initrd.img-6.5.7-kirkwood-tld-1
<DIR> 4096 dts
198312 config-6.5.7-kirkwood-tld-1
4543778 System.map-6.5.7-kirkwood-tld-1
6236933 zImage.fdt
6235900 uImage.orig
Marvell>> setenv bootcmd 'run usb_bootcmd; usb stop; reset'
Marvell>> boot

** Unable to read "/boot/uImage" from usb 0:1 **
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
.......................................................................................................................................................

5791271 bytes read
## Booting image at 00800000 ...
Bad Magic Number
stopping USB..

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found

** Unable to read "/boot/uImage" from usb 0:1 **
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
.......................................................................................................................................................

5791271 bytes read
## Booting image at 00800000 ...
Bad Magic Number
stopping USB..

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
Marvell>>
Marvell>>

Jan_Grz1,

> > Hit any key to stop autoboot: 0
>
>

> usb start
> sleep 3
> usb info
> usb part
> ext2ls usb 0:1 /boot
>

>
> If all went well above

Output of ext2ls was not good. /boot/uImage was not listed.

This u-boot seems flaky. "usb start" spins up the drive, but it seems to take a long time. Try this

help
usb start
echo Waiting for all USB drives to spin up.................................................. ;
ext2ls usb 0:1 /boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 03/14/2025 12:50AM by bodhi.

bodhi,



__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
Marvell>>
Marvell>>
Marvell>> help
? - alias for 'help'
SatR - sample at reset sub-system, relevent for DB only
base - print or set address offset
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootext2 dev:boot_part1,boot_part2 addr boot_image linux_dev_name
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
bubt - Burn an image on the Boot Flash.
chpart - change active partition
cmp - memory compare
cmpm - Compare Memory
cp - memory copy
cpumap - Display CPU memory mapping settings.
crc32 - checksum calculation
date - get/set/reset date & time
dclk - Display the MV device CLKs.
dhcp - invoke DHCP client to obtain IP/boot params
diskboot- boot from IDE device
echo - echo args to console
eeprom - EEPROM sub-system
erase - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2ls - list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
fi - Find value in the memory.
flinfo - print FLASH memory information
fsinfo - print information about filesystems
fsload - load binary file from a filesystem image
g - start application at cached address 'addr'(default addr 0x40000)
go - start application at address 'addr'
help - print online help
icrc32 - checksum calculation
ide - IDE sub-system
iloop - infinite loop on address range
imd - i2c memory display
iminfo - print header information for application image
imm[.b, .s, .w, .l] - i2c memory modify (auto-incrementing)
imw - memory write (fill)
inm - memory modify (constant address)
iprobe - probe to discover valid I2C chip addresses
ir - reading and changing MV internal register values.
loop - infinite loop on address range
ls - list files in a directory (default /)
map - Diasplay address decode windows
md - memory display
me - PCI master enable
mm - memory modify (auto-incrementing)
mmcinit - init mmc card
mp - map PCI BAR
mtdparts- define flash/nand partitions
mtest - simple RAM test
mw - memory write (fill)
nm - memory modify (constant address)
pci - list and access PCI Configuration Space
phyRead - Read PCI-E Phy register
pciePhyWrite - Write PCI-E Phy register
phyRead - Read Phy register
phyWrite - Write Phy register
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
rcvr - Satrt recovery process (Distress Beacon with TFTP server)
reset - Perform RESET of the CPU
resetenv - Return all environment variable to default.
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
se - PCI Slave enable
setenv - set environment variables
sflash - read, write or erase the external SPI Flash.
sg - scanning the PHYs status
sp - Scan PCI bus.
switchRegRead - Read switch register
switchRegWrite - Write switch register
Temp - read chip Tj temp
tftpboot- boot image via network using TFTP protocol
usb - USB sub-system
usbboot - boot from USB device
version - print monitor version
Marvell>> usb start
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
Marvell>> echo Waiting for all USB drives to spin up.................................................. ;
Waiting for all USB drives to spin up..................................................
Marvell>> ext2ls usb 0:1 /boot
<DIR> 4096 .
<DIR> 4096 ..
6223880 zImage-6.5.7-kirkwood-tld-1
8557164 linux-headers-6.5.7-kirkwood-tld-1_1_armel.deb
6223880 vmlinuz-6.5.7-kirkwood-tld-1
5791271 uInitrd
5791207 initrd.img-6.5.7-kirkwood-tld-1
<DIR> 4096 dts
198312 config-6.5.7-kirkwood-tld-1
4543778 System.map-6.5.7-kirkwood-tld-1
6236933 zImage.fdt
6223944 uImage.orig
Marvell>> boot
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
0 Storage Device(s) found
** Bad partition 1 **
** Bad partition 1 **
## Booting image at 00800000 ...
Bad Magic Number
stopping USB..

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found

** Unable to read "/boot/uImage" from usb 0:1 **
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
.......................................................................................................................................................

5791271 bytes read
## Booting image at 00800000 ...
Bad Magic Number
stopping USB..

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>

Marvell>> ext2ls usb 0:1 /boot
<DIR> 4096 .
<DIR> 4096 ..
6223880 zImage-6.5.7-kirkwood-tld-1
8557164 linux-headers-6.5.7-kirkwood-tld-1_1_armel.deb
6223880 vmlinuz-6.5.7-kirkwood-tld-1
5791271 uInitrd
5791207 initrd.img-6.5.7-kirkwood-tld-1
<DIR> 4096 dts
198312 config-6.5.7-kirkwood-tld-1
4543778 System.map-6.5.7-kirkwood-tld-1
6236933 zImage.fdt
6235900 uImage.orig

Have you verified the uImage file is actually there? I haven't seen anything in the thread showing it existing. Likewise I don't see output from the mkimage command etc. This looks more like the file just not being present than some sort of IO error at first glance.

> Have you verified the uImage file is actually
> there? I haven't seen anything in the thread
> showing it existing. Likewise I don't see output
> from the mkimage command etc. This looks more like
> the file just not being present than some sort of
> IO error at first glance.

It was loaded successfully once up here:

https://forum.doozan.com/read.php?2,139275,139305#msg-139305

Marvell>> boot
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found

## Booting image at 00800000 ...
   Image Name:   Linux-6.5.7-kirkwood-tld-1
   Created:      2025-03-08  14:28:17 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    6235836 Bytes =  5.9 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
   Image Name:   initramfs-6.5.7-kirkwood-tld-1
   Created:      2023-10-31  22:53:55 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5791207 Bytes =  5.5 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

But yes, it's a good idea to take the rootfs to another Linux box and verify that it's there, to be sure.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi,

I have attached a screenshot of reading the usb stick on a Linux vm.

Jan_Grz1,

You need to recreate the rootfs using the kirkwood-lenovo-ix2-ng.dtb in Step 4.

https://forum.doozan.com/read.php?2,12096

Quote

4. (Stock u-boot only) Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Skip this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time, or running kwboot with latest u-boot image).

Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box (see the folder /media/sdb1/boot/dts for the exact spelling of your Kirkwood box name).

Generate the uImage with DTB embedded inside:
cd /media/sdb1/boot
cp -a zImage-6.5.7-kirkwood-tld-1 zImage.fdt
cat dts/kirkwood-lenovo-ix2-ng.dtb >> zImage.fdt
mv uImage uImage.orig
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.5.7-kirkwood-tld-1 -d zImage.fdt uImage
sync

If your Linux box does not have mkimage, then install it
apt-get install u-boot-tools

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi,

I have tried but somehow it gets stuck here.


root@archiso ~ # cd /mnt/boot
root@archiso /mnt/boot # cp -a zImage-6.5.7-kirkwood-tld-1 zImage.fdt
root@archiso /mnt/boot # cat /mnt/boot/dts/kirkwood-lenovo-ix2-ng.dtb >> zImage.fdt
root@archiso /mnt/boot # mv uImage uImage.orig
root@archiso /mnt/boot # mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.5.7-kirkwood-tld-1 -d zImage.fdt uImage
zsh: command not found: mkimage
127 root@archiso /mnt/boot # pacman -Sy uboot-tools
:: Synchronizing package databases...
core 116.7 KiB 2.00 MiB/s 00:00 [####################################] 100%
extra 7.7 MiB 33.5 MiB/s 00:00 [####################################] 100%
resolving dependencies...
looking for conflicting packages...

Packages (1) uboot-tools-2025.01-1

Total Download Size: 0.21 MiB
Total Installed Size: 0.79 MiB

:: Proceed with installation? [Y/n] Y
:: Retrieving packages...
uboot-tools-2025.01-1-x86_64 215.2 KiB 3.69 MiB/s 00:00 [####################################] 100%
(1/1) checking keys in keyring [####################################] 100%
(1/1) checking package integrity [####################################] 100%
(1/1) loading package files [####################################] 100%
(1/1) checking for file conflicts [####################################] 100%
(1/1) checking available disk space [####################################] 100%
:: Processing package changes...
(1/1) installing uboot-tools [####################################] 100%
:: Running post-transaction hooks...
(1/1) Arming ConditionNeedsUpdate...
root@archiso /mnt/boot # mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.5.7-kirkwood-tld-1 -d zImage.fdt uImage

bodhi,


ok never mind it just took a long time. But when I try to umount it then it says target is busy


root@archiso ~ # cd /mnt/boot
root@archiso /mnt/boot # cp -a zImage-6.5.7-kirkwood-tld-1 zImage.fdt
root@archiso /mnt/boot # cat /mnt/boot/dts/kirkwood-lenovo-ix2-ng.dtb >> zImage.fdt
root@archiso /mnt/boot # mv uImage uImage.orig
root@archiso /mnt/boot # mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.5.7-kirkwood-tld-1 -d zImage.fdt uImage
zsh: command not found: mkimage
127 root@archiso /mnt/boot # pacman -Sy uboot-tools
:: Synchronizing package databases...
core 116.7 KiB 2.00 MiB/s 00:00 [####################################] 100%
extra 7.7 MiB 33.5 MiB/s 00:00 [####################################] 100%
resolving dependencies...
looking for conflicting packages...

Packages (1) uboot-tools-2025.01-1

Total Download Size: 0.21 MiB
Total Installed Size: 0.79 MiB

:: Proceed with installation? [Y/n] Y
:: Retrieving packages...
uboot-tools-2025.01-1-x86_64 215.2 KiB 3.69 MiB/s 00:00 [####################################] 100%
(1/1) checking keys in keyring [####################################] 100%
(1/1) checking package integrity [####################################] 100%
(1/1) loading package files [####################################] 100%
(1/1) checking for file conflicts [####################################] 100%
(1/1) checking available disk space [####################################] 100%
:: Processing package changes...
(1/1) installing uboot-tools [####################################] 100%
:: Running post-transaction hooks...
(1/1) Arming ConditionNeedsUpdate...
root@archiso /mnt/boot # mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.5.7-kirkwood-tld-1 -d zImage.fdt uImage
^C
130 root@archiso /mnt/boot # ls
System.map-6.5.7-kirkwood-tld-1 uImage.orig
config-6.5.7-kirkwood-tld-1 uInitrd
dts vmlinuz-6.5.7-kirkwood-tld-1
initrd.img-6.5.7-kirkwood-tld-1 zImage.fdt
linux-headers-6.5.7-kirkwood-tld-1_1_armel.deb zImage-6.5.7-kirkwood-tld-1
uImage
root@archiso /mnt/boot # sync
root@archiso /mnt/boot # umount /mnt
umount: /mnt: target is busy.
32 root@archiso /mnt/boot # umount /mnt
umount: /mnt: target is busy.
32 root@archiso /mnt/boot #

now it has worked after many attempts

bodhi,

what now??



__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
..................................................................................................................................................................................................

6236997 bytes read
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
.......................................................................................................................................................

5791271 bytes read
## Booting image at 00800000 ...
Image Name: Linux-6.5.7-kirkwood-tld-1
Created: 2025-03-16 13:08:04 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6236933 Bytes = 5.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
Image Name: initramfs-6.5.7-kirkwood-tld-1
Created: 2023-10-31 22:53:55 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5791207 Bytes = 5.5 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK

Starting kernel ...

[ 4.147263][ T1] printk: console [ttyS0] enabled
[ 4.157066][ T1] printk: bootconsole [earlycon0] disabled
[ 4.199581][ T1] loop: module loaded
[ 4.204309][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 4.213785][ T1] scsi host0: sata_mv
[ 4.218864][ T1] scsi host1: sata_mv
[ 4.223137][ T1] ata1: SATA max UDMA/133 irq 28
[ 4.227958][ T1] ata2: SATA max UDMA/133 irq 28
[ 4.234879][ T1] spi-nor spi0.0: mx25l8005 (1024 Kbytes)
[ 4.240640][ T1] 3 fixed-partitions partitions found on MTD device spi0.0
[ 4.247725][ T1] Creating 3 MTD partitions on "spi0.0":
[ 4.253290][ T1] 0x000000000000-0x00000007e000 : "u-boot"
[ 4.259718][ T1] 0x00000007e000-0x00000007f000 : "u-boot env2"
[ 4.266398][ T1] 0x00000007f000-0x000000080000 : "u-boot env"
[ 4.273633][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 4.282233][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 4.313555][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 4.323663][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address aa:00:00:00:00:01
[ 4.333771][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 4.340084][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 4.348671][ T1] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[ 4.379085][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 4.386126][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[ 4.395162][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.403133][ T1] usb usb1: Product: EHCI Host Controller
[ 4.408731][ T1] usb usb1: Manufacturer: Linux 6.5.7-kirkwood-tld-1 ehci_hcd
[ 4.416089][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 4.422357][ T1] hub 1-0:1.0: USB hub found
[ 4.426861][ T1] hub 1-0:1.0: 1 port detected
[ 4.432320][ T1] usbcore: registered new interface driver usb-storage
[ 4.439590][ T1] mousedev: PS/2 mouse device common for all mice
[ 4.447136][ T1] rtc-mv f1010300.rtc: registered as rtc0
[ 4.452845][ T1] rtc-mv f1010300.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800)
[ 4.462442][ T1] i2c_dev: i2c /dev entries driver
[ 4.469552][ T1] device-mapper: uevent: version 1.0.3
[ 4.475375][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[ 4.485197][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 4.492538][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 4.499956][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 4.507424][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 4.516281][ T1] ledtrig-cpu: registered to indicate activity on CPUs
[ 4.523170][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 4.529443][ T1] drop_monitor: Initializing network drop monitor service
[ 4.537678][ T1] NET: Registered PF_INET6 protocol family
[ 4.545128][ T1] Segment Routing with IPv6
[ 4.549692][ T1] RPL Segment Routing with IPv6
[ 4.554501][ T1] In-situ OAM (IOAM) with IPv6
[ 4.559378][ T1] NET: Registered PF_PACKET protocol family
[ 4.565454][ T1] Key type dns_resolver registered
[ 4.585220][ T1] registered taskstats version 1
[ 4.590181][ T1] Loading compiled-in X.509 certificates
[ 4.612590][ T1] Key type .fscrypt registered
[ 4.617247][ T1] Key type fscrypt-provisioning registered
[ 4.628024][ T1] Key type big_key registered
[ 4.668054][ T1] Key type encrypted registered
[ 4.719157][ T49] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 4.762166][ T104] "cryptomgr_test" (104) uses obsolete ecb(arc4) skcipher
[ 4.938678][ T49] usb 1-1: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 0.01
[ 4.947674][ T52] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 4.969060][ T49] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.976937][ T49] usb 1-1: Product: DataTraveler 3.0
[ 4.989063][ T49] usb 1-1: Manufacturer: Kingston
[ 4.993967][ T49] usb 1-1: SerialNumber: 60A44C413C8CF19059850057
[ 5.019831][ T52] ata1.00: ATA-10: WDC WD10EZEX-08WN4A0, 01.01A01, max UDMA/100
[ 5.027589][ T49] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 5.034473][ T52] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 5.049418][ T49] scsi host2: usb-storage 1-1:1.0
[ 5.059732][ T52] ata1.00: configured for UDMA/100
[ 5.075221][ T29] scsi 0:0:0:0: Direct-Access ATA WDC WD10EZEX-08W 1A01 PQ: 0 ANSI: 5
[ 5.100342][ T10] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 5.108752][ T10] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 5.129145][ T10] sd 0:0:0:0: [sda] Write Protect is off
[ 5.134754][ T10] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.159161][ T10] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[ 5.204765][ T10] sda: sda1
[ 5.219208][ T10] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.609070][ T54] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 5.629083][ T54] ata2.00: ATA-9: HGST HTS721010A9E630, JB0OA3T0, max UDMA/133
[ 5.636528][ T54] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 5.663574][ T54] ata2.00: configured for UDMA/133
[ 5.689202][ T18] scsi 1:0:0:0: Direct-Access ATA HGST HTS721010A9 A3T0 PQ: 0 ANSI: 5
[ 5.699356][ T10] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 5.707763][ T10] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 5.729455][ T10] sd 1:0:0:0: [sdb] Write Protect is off
[ 5.735062][ T10] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.759165][ T10] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
[ 6.085974][ T10] sdb: sdb1 sdb2
[ 6.091124][ T18] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6
[ 6.109589][ T10] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 6.116827][ T10] sd 2:0:0:0: [sdc] 30218842 512-byte logical blocks: (15.5 GB/14.4 GiB)
[ 6.139576][ T10] sd 2:0:0:0: [sdc] Write Protect is off
[ 6.149071][ T10] sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 6.174514][ T10] sdc: sdc1
[ 6.189278][ T10] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[ 6.750302][ T1] clk: Disabling unused clocks
[ 6.758227][ T1] Freeing unused kernel image (initmem) memory: 1024K
[ 6.789610][ T1] Checked W+X mappings: passed, no W+X pages found
[ 6.796017][ T1] Run /init as init process
Loading, please wait...
Starting systemd-udevd version 252.17-1~deb12u1
[ 7.913025][ T154] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.38.1
[/sbin/fsck.ext3 (1) -- /dev/sdc1] fsck.ext3 -a -C0 /dev/sdc1
rootfs: clean, 18527/944704 files, 330740/3777099 blocks
done.
[ 18.866979][ T180] EXT4-fs (sdc1): mounting ext3 file system using the ext4 subsystem
[ 18.930224][ T180] EXT4-fs (sdc1): mounted filesystem 200d8649-5760-4fff-b27f-bcb70b904b65 ro with ordered data mode. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
mount: mounting /run on /root/run failed: No such file or directory
mount: mounting /sys on /root/sys failed: No such file or directory
run-init: can't [ 19.139519][ T1] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000100
[ 19.149232][ T1] CPU: 0 PID: 1 Comm: run-init Not tainted 6.5.7-kirkwood-tld-1 #2 b782412796a181fef4037ede16903ece36aa46a3
[ 19.160599][ T1] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[ 19.167600][ T1] unwind_backtrace from show_stack+0x10/0x14
[ 19.173567][ T1] show_stack from dump_stack_lvl+0x28/0x30
[ 19.179357][ T1] dump_stack_lvl from panic+0xf0/0x320
[ 19.184790][ T1] panic from do_exit+0x274/0xa28
[ 19.189707][ T1] do_exit from sys_exit_group+0x0/0x14
[ 19.195148][ T1] sys_exit_group from sys_exit_group+0x10/0x14
[ 19.201287][ T1] sys_exit_group from ret_fast_syscall+0x0/0x44
[ 19.207503][ T1] Exception stack(0x90819fa8 to 0x90819ff0)
[ 19.213281][ T1] 9fa0: 00000001 76f0b888 00000001 00000000 00000001 00000000
[ 19.222203][ T1] 9fc0: 00000001 76f0b888 00000000 000000f8 76f2e368 76f0d000 00000000 76f0e558
[ 19.231120][ T1] 9fe0: 00000000 7ea91b68 76dce1e4 76e54544
[ 19.236897][ T1] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000100 ]---
execute '/sbin/init': No such file or directory

root@archiso /mnt/boot # mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.5.7-kirkwood-tld-1 -d zImage.fdt uImage 
^C 
130 root@archiso /mnt/boot # ls 
System.map-6.5.7-kirkwood-tld-1 uImage.orig 
config-6.5.7-kirkwood-tld-1 uInitrd 
dts vmlinuz-6.5.7-kirkwood-tld-1 
initrd.img-6.5.7-kirkwood-tld-1 zImage.fdt 
linux-headers-6.5.7-kirkwood-tld-1_1_armel.deb zImage-6.5.7-kirkwood-tld-1 
uImage 
root@archiso /mnt/boot # sync 
root@archiso /mnt/boot # umount /mnt 
umount: /mnt: target is busy. 
32 root@archiso /mnt/boot # umount /mnt 
umount: /mnt: target is busy. 
32 root@archiso /mnt/boot #

The problem above is because you're trying to unmount while still inside the rootfs folder. You must change directory to another place before unmounting. For example,

cd /

[ 18.866979][ T180] EXT4-fs (sdc1): mounting ext3 file system using the ext4 subsystem 
[ 18.930224][ T180] EXT4-fs (sdc1): mounted filesystem 200d8649-5760-4fff-b27f-bcb70b904b65 ro with ordered data mode. Quota mode: none. 
done. 
Begin: Running /scripts/local-bottom ... done. 
Begin: Running /scripts/init-bottom ... done. 
mount: mounting /run on /root/run failed: No such file or directory 
mount: mounting /sys on /root/sys failed: No such file or directory

The error above usally is because the rootfs is bad.

====

Repeat the rootfs creation and post the entire log of what you did here. I'll look it over.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi,


root@archiso ~ # lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS
loop0 7:0 0 824.9M 1 loop /run/archiso/airootfs
sda 8:0 0 6.4G 0 disk
sdb 8:16 1 14.4G 0 disk
sr0 11:0 1 1.2G 0 rom /run/archiso/bootmnt
root@archiso ~ # fdisk /dev/sdb

Welcome to fdisk (util-linux 2.40.4).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.


Command (m for help): o
Created a new DOS (MBR) disklabel with disk identifier 0x9a0244da.

Command (m for help): n
Partition type
p primary (0 primary, 0 extended, 4 free)
e extended (container for logical partitions)
Select (default p): p
Partition number (1-4, default 1):
First sector (2048-30218841, default 2048):
Last sector, +/-sectors or +/-size{K,M,G,T,P} (2048-30218841, default 30218841):

Created a new partition 1 of type 'Linux' and of size 14.4 GiB.
Partition #1 contains a vfat signature.

Do you want to remove the signature? [Y]es/[N]o: Y

The signature will be removed by a write command.

Command (m for help): w
The partition table has been altered.
Calling ioctl() to re-read partition table.
Syncing disks.

root@archiso ~ # mkfs.ext3 /dev/sdb1
mke2fs 1.47.2 (1-Jan-2025)
Creating filesystem with 3777099 4k blocks and 944704 inodes
Filesystem UUID: d26f2544-3ca4-486c-a172-d7fbf34a06b8
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208

Allocating group tables: done
Writing inode tables: done
Creating journal (16384 blocks): done
Writing superblocks and filesystem accounting information: done

root@archiso ~ # e2label /dev/sdb1 rootfs
root@archiso ~ # mount /dev/sdb1 /mnt
root@archiso ~ # cd /mnt
root@archiso /mnt # ls
Debian-6.5.7-kirkwood-tld-1-rootfs-bodhi.tar.bz2 lost+found
root@archiso /mnt # tar yjf Debian-6.5.7-kirkwood-tld-1-rootfs-bodhi.tar.bz2
tar: invalid option -- 'y'
Try 'tar --help' or 'tar --usage' for more information.
64 root@archiso /mnt # tar xjf Debian-6.5.7-kirkwood-tld-1-rootfs-bodhi.tar.bz2
tar xjf Debian-6.5.7-kirkwood-tld-1-rootfs-bodhi.tar.bz2 20.96s user 8.87s system 25% cpu 1:55.40 total
root@archiso /mnt # cd /mnt/boot
root@archiso /mnt/boot # cp -a zImage-6.5.7-kirkwood-tld-1 zImage.fdt
root@archiso /mnt/boot # cat /mnt/boot/dts/kirkwood-lenovo-ix2-ng.dtb >> zImage.fdt
root@archiso /mnt/boot # mv uImage uImage.orig
root@archiso /mnt/boot # mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.5.7-kirkwood-tld-1 -d zImage.fdt uImage
zsh: command not found: mkimage
127 root@archiso /mnt/boot # pacman -Sy uboot-tools
:: Synchronizing package databases...
core 116.7 KiB 628 KiB/s 00:00 [####################################] 100%
extra 7.7 MiB 28.2 MiB/s 00:00 [####################################] 100%
resolving dependencies...
looking for conflicting packages...

Packages (1) uboot-tools-2025.01-1

Total Download Size: 0.21 MiB
Total Installed Size: 0.79 MiB

:: Proceed with installation? [Y/n] Y
:: Retrieving packages...
uboot-tools-2025.01-1-x86_64 215.2 KiB 1793 KiB/s 00:00 [####################################] 100%
(1/1) checking keys in keyring [####################################] 100%
(1/1) checking package integrity [####################################] 100%
(1/1) loading package files [####################################] 100%
(1/1) checking for file conflicts [####################################] 100%
(1/1) checking available disk space [####################################] 100%
:: Processing package changes...
(1/1) installing uboot-tools [####################################] 100%
:: Running post-transaction hooks...
(1/1) Arming ConditionNeedsUpdate...
root@archiso /mnt/boot # mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.5.7-kirkwood-tld-1 -d zImage.fdt uImage


I have always managed to get to this point without any problems, but then it hangs up and does nothing. by the way, I connect to a Linux VM via Solar Putty. In the meantime it shows error messages in the VM. (to be seen in the screenshot). Sometimes it works when I try again, but sometimes not.

Now it has worked.



root@archiso ~ # cd /mnt/boot
root@archiso /mnt/boot # cp -a zImage-6.5.7-kirkwood-tld-1 zImage.fdt
root@archiso /mnt/boot # cat /mnt/boot/dts/kirkwood-lenovo-ix2-ng.dtb >> zImage.fdt
root@archiso /mnt/boot # mv uImage uImage.orig
root@archiso /mnt/boot # mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.5.7-kirkwood-tld-1 -d zImage.fdt uImage
Image Name: Linux-6.5.7-kirkwood-tld-1
Created: Sun Mar 16 20:37:15 2025
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6236933 Bytes = 6090.75 KiB = 5.95 MiB
Load Address: 00008000
Entry Point: 00008000
root@archiso /mnt/boot # sync
root@archiso /mnt/boot # cd /
root@archiso / # cd --
root@archiso ~ # umount /mnt
root@archiso ~ # sync
root@archiso ~ #



Edited 1 time(s). Last edit at 03/16/2025 03:41PM by Jan_Grz1.

bodhi,


i have now tried plugging the usb stick into the nas and it looks like it is working. There are two error messages at the end. How do I fix this?




__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 0]: Enable DMA mode (6)
Device 1 @ 0 1:
Model: HGST HTS721010A9E630 Firm: JB0OA3T0 Ser#: JR1000D33KPNWE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
..................................................................................................................................................................................................

6236997 bytes read
....
.
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
....
.......................................................................................................................................................

5791271 bytes read
## Booting image at 00800000 ...
Image Name: Linux-6.5.7-kirkwood-tld-1
Created: 2025-03-16 20:37:15 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6236933 Bytes = 5.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02100000 ...
Image Name: initramfs-6.5.7-kirkwood-tld-1
Created: 2023-10-31 22:53:55 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5791207 Bytes = 5.5 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK

Starting kernel ...

[ 4.147265][ T1] printk: console [ttyS0] enabled
[ 4.157066][ T1] printk: bootconsole [earlycon0] disabled
[ 4.199610][ T1] loop: module loaded
[ 4.204340][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 4.213831][ T1] scsi host0: sata_mv
[ 4.218905][ T1] scsi host1: sata_mv
[ 4.223176][ T1] ata1: SATA max UDMA/133 irq 28
[ 4.228000][ T1] ata2: SATA max UDMA/133 irq 28
[ 4.234925][ T1] spi-nor spi0.0: mx25l8005 (1024 Kbytes)
[ 4.240694][ T1] 3 fixed-partitions partitions found on MTD device spi0.0
[ 4.247786][ T1] Creating 3 MTD partitions on "spi0.0":
[ 4.253353][ T1] 0x000000000000-0x00000007e000 : "u-boot"
[ 4.259782][ T1] 0x00000007e000-0x00000007f000 : "u-boot env2"
[ 4.266462][ T1] 0x00000007f000-0x000000080000 : "u-boot env"
[ 4.273700][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 4.282305][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 4.313594][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 4.323697][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address aa:00:00:00:00:01
[ 4.333799][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 4.340110][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 4.348776][ T1] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[ 4.379090][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 4.386137][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[ 4.395170][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.403149][ T1] usb usb1: Product: EHCI Host Controller
[ 4.408749][ T1] usb usb1: Manufacturer: Linux 6.5.7-kirkwood-tld-1 ehci_hcd
[ 4.416107][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 4.422376][ T1] hub 1-0:1.0: USB hub found
[ 4.426888][ T1] hub 1-0:1.0: 1 port detected
[ 4.432344][ T1] usbcore: registered new interface driver usb-storage
[ 4.439617][ T1] mousedev: PS/2 mouse device common for all mice
[ 4.447174][ T1] rtc-mv f1010300.rtc: registered as rtc0
[ 4.452891][ T1] rtc-mv f1010300.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800)
[ 4.462497][ T1] i2c_dev: i2c /dev entries driver
[ 4.469596][ T1] device-mapper: uevent: version 1.0.3
[ 4.475419][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[ 4.485251][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 4.492593][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 4.500017][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 4.507485][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 4.516338][ T1] ledtrig-cpu: registered to indicate activity on CPUs
[ 4.523223][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 4.529494][ T1] drop_monitor: Initializing network drop monitor service
[ 4.537727][ T1] NET: Registered PF_INET6 protocol family
[ 4.545180][ T1] Segment Routing with IPv6
[ 4.549746][ T1] RPL Segment Routing with IPv6
[ 4.554550][ T1] In-situ OAM (IOAM) with IPv6
[ 4.559434][ T1] NET: Registered PF_PACKET protocol family
[ 4.565505][ T1] Key type dns_resolver registered
[ 4.585284][ T1] registered taskstats version 1
[ 4.590250][ T1] Loading compiled-in X.509 certificates
[ 4.612655][ T1] Key type .fscrypt registered
[ 4.617317][ T1] Key type fscrypt-provisioning registered
[ 4.628088][ T1] Key type big_key registered
[ 4.668253][ T1] Key type encrypted registered
[ 4.719172][ T49] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 4.762316][ T104] "cryptomgr_test" (104) uses obsolete ecb(arc4) skcipher
[ 4.938534][ T49] usb 1-1: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 0.01
[ 4.947524][ T52] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 4.969067][ T49] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.976945][ T49] usb 1-1: Product: DataTraveler 3.0
[ 4.989070][ T49] usb 1-1: Manufacturer: Kingston
[ 4.993974][ T49] usb 1-1: SerialNumber: 60A44C413C8CF19059850057
[ 5.020097][ T49] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 5.027015][ T52] ata1.00: ATA-10: WDC WD10EZEX-08WN4A0, 01.01A01, max UDMA/100
[ 5.049072][ T52] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 5.057319][ T49] scsi host2: usb-storage 1-1:1.0
[ 5.065436][ T52] ata1.00: configured for UDMA/100
[ 5.089555][ T29] scsi 0:0:0:0: Direct-Access ATA WDC WD10EZEX-08W 1A01 PQ: 0 ANSI: 5
[ 5.109701][ T10] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 5.118109][ T10] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 5.139152][ T10] sd 0:0:0:0: [sda] Write Protect is off
[ 5.144764][ T10] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.169167][ T10] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[ 5.224690][ T10] sda: sda1
[ 5.239211][ T10] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.619077][ T54] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 5.639090][ T54] ata2.00: ATA-9: HGST HTS721010A9E630, JB0OA3T0, max UDMA/133
[ 5.646529][ T54] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 5.663929][ T54] ata2.00: configured for UDMA/133
[ 5.689521][ T18] scsi 1:0:0:0: Direct-Access ATA HGST HTS721010A9 A3T0 PQ: 0 ANSI: 5
[ 5.709712][ T10] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 5.718114][ T10] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 5.739130][ T10] sd 1:0:0:0: [sdb] Write Protect is off
[ 5.744739][ T10] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.769164][ T10] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
[ 6.090603][ T18] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6
[ 6.100247][ T10] sdb: sdb1 sdb2
[ 6.109597][ T10] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 6.120933][ T18] sd 2:0:0:0: [sdc] 30218842 512-byte logical blocks: (15.5 GB/14.4 GiB)
[ 6.139556][ T18] sd 2:0:0:0: [sdc] Write Protect is off
[ 6.149090][ T18] sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 6.174495][ T18] sdc: sdc1
[ 6.189287][ T18] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[ 6.750523][ T1] clk: Disabling unused clocks
[ 6.758456][ T1] Freeing unused kernel image (initmem) memory: 1024K
[ 6.789616][ T1] Checked W+X mappings: passed, no W+X pages found
[ 6.796017][ T1] Run /init as init process
Loading, please wait...
Starting systemd-udevd version 252.17-1~deb12u1
[ 7.935898][ T157] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.38.1
[/sbin/fsck.ext3 (1) -- /dev/sdc1] fsck.ext3 -a -C0 /dev/sdc1
rootfs: clean, 20040/944704 files, 334758/3777099 blocks
done.
[ 18.847089][ T181] EXT4-fs (sdc1): mounting ext3 file system using the ext4 subsystem
[ 18.915678][ T181] EXT4-fs (sdc1): mounted filesystem d26f2544-3ca4-486c-a172-d7fbf34a06b8 ro with ordered data mode. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 3.06 booting
INIT: No inittab.d directory found
Using makefile-style concurrent boot in runlevel S.
Setting hostname to 'debian'...done.
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[ 21.545288][ T364] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 21.893235][ T371] adt7475 0-002e: ADT7473 device, revision 0
[ 21.921916][ T360] orion_wdt: Initial timeout 21 sec
[ 22.009486][ T371] adt7475 0-002e: Optional features: fan4 pwm2
[ 22.225167][ T364] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 22.288767][ T121] random: crng init done
[ 22.305857][ T364] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 22.386359][ T357] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 22.409901][ T364] sd 2:0:0:0: Attached scsi generic sg2 type 0
done.
Activating swap:.
[ 32.590574][ T520] EXT4-fs (sdc1): re-mounted d26f2544-3ca4-486c-a172-d7fbf34a06b8 r/w. Quota mode: none.
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
/tmp.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Starting Setting kernel variables: sysctl.
Initializing random number generator...done.
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/aa:00:00:00:00:01
Sending on LPF/eth0/aa:00:00:00:00:01
Sending on Socket/fallback
DHCPREQUEST for 192.168.0.17 on eth0 to 255.255.255.255 port 67
[ 38.249973][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
DHCPREQUEST for 192.168.0.17 on eth0 to 255.255.255.255 port 67
DHCPREQUEST for 192.168.0.17 on eth0 to 255.255.255.255 port 67
DHCPNAK from 192.168.178.1
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6
DHCPOFFER of 192.168.178.78 from 192.168.178.1
DHCPREQUEST for 192.168.178.78 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.178.78 from 192.168.178.1
invoke-rc.d: could not determine current runlevel
invoke-rc.d: could not determine current runlevel
bound to 192.168.178.78 -- renewal in 386005 seconds.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Not starting NFS kernel daemon: no exports ... (warning).
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1055 (syslogd)
.
Starting NTP server: ntpd1999-12-31T16:00:40 ntpd[1077]: INIT: ntpd ntpsec-1.2.2: Starting
1999-12-31T16:00:40 ntpd[1077]: INIT: Command line: /usr/sbin/ntpd -p /var/run/ntpd.pid -g -c /run/ntp.conf.dhcp -u 104:106
.
Starting system message bus: dbus.
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Starting NTP server: ntpd.
Starting OpenBSD Secure Shell server: sshdsshd: no hostkeys available -- exiting.
failed!
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1079 (klogd)
.
Running local boot scripts (/etc/rc.local)
ssh-keygen: generating new host keys: RSA
ECDSA
ED25519

Starting OpenBSD Secure Shell server: sshd
.
.

Debian GNU/Linux 12 debian ttyS0

debian login:

bodhi,

I have now updated everything. What do I have to do now to make everything work?



debian login: root
Password:
Linux debian 6.5.7-kirkwood-tld-1 #2 PREEMPT Wed Oct 18 21:14:11 PDT 2023 armv5tel

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
Last login: Tue Oct 31 18:33:32 PDT 2023 from fe80::4f8:63a5:4900:ad47%eth0 on pts/0
debian
192.168.178.7
Lenovo IX2-ng
Linux version 6.5.7-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.4 0) #2 PREEMPT Wed Oct 18 21:14:11 PDT 2023
Debian 12.2
Sun Mar 16 14:01:10 PDT 2025 up 17 minutes
root@debian:~# apt-get install dphys-swapfile
Reading package lists... Done
Building dependency tree... Done
Reading state information... Done
The following packages were automatically installed and are no longer required:
bind9-host bind9-libs libbpf0 libcbor0 libdns-export1110 libevent-2.1-7
libffi7 libfstrm0 libicu67 libicu72 libisc-export1105 libjemalloc2
libjson-c5 libldap-2.4-2 liblmdb0 libmaxminddb0 libncurses6 libnghttp2-14
libopts25 libpcre3 libprocps8 libprotobuf-c1 libssl1.1 libuv1 libxml2
Use 'apt autoremove' to remove them.
The following additional packages will be installed:
dc
The following NEW packages will be installed:
dc dphys-swapfile
0 upgraded, 2 newly installed, 0 to remove and 0 not upgraded.
Need to get 88.4 kB of archives.
After this operation, 209 kB of additional disk space will be used.
Do you want to continue? [Y/n] Y
Get:1 http://ftp.us.debian.org/debian bookworm/main armel dc armel 1.07.1-3 [69.0 kB]
Get:2 http://ftp.us.debian.org/debian bookworm/main armel dphys-swapfile all 20100506-7.1 [19.4 kB]
Fetched 88.4 kB in 1s (124 kB/s)
Selecting previously unselected package dc.
(Reading database ... 16869 files and directories currently installed.)
Preparing to unpack .../archives/dc_1.07.1-3_armel.deb ...
Unpacking dc (1.07.1-3) ...
Selecting previously unselected package dphys-swapfile.
Preparing to unpack .../dphys-swapfile_20100506-7.1_all.deb ...
Unpacking dphys-swapfile (20100506-7.1) ...
Setting up dc (1.07.1-3) ...
Setting up dphys-swapfile (20100506-7.1) ...
Starting dphys-swapfile swapfile setup ...
computing size, want /var/swap=486MByte, generating swapfile ... of 486MBytes
[ 1914.090304][ T1259] Adding 497660k swap on /var/swap. Priority:-2 extents:13 across:12435744k FS
done.
Processing triggers for man-db (2.11.2-2) ...
root@debian:~# CONF_SWAPFACTOR=4
root@debian:~# date
Sun Mar 16 14:18:20 PDT 2025
root@debian:~# apt-get update
Get:2 http://ftp.us.debian.org/debian bookworm InRelease [151 kB]
Get:1 http://deb.debian.org/debian bookworm-updates InRelease [55.4 kB]
Get:3 https://security.debian.org/debian-security bookworm-security InRelease [48.0 kB]
Get:4 http://deb.debian.org/debian bookworm-updates/non-free-firmware Sources [2076 B]
Get:5 http://deb.debian.org/debian bookworm-updates/main Sources.diff/Index [15.1 kB]
Ign:5 http://deb.debian.org/debian bookworm-updates/main Sources.diff/Index
Get:6 http://deb.debian.org/debian bookworm-updates/main armel Packages.diff/Index [15.1 kB]
Ign:6 http://deb.debian.org/debian bookworm-updates/main armel Packages.diff/Index
Get:7 http://deb.debian.org/debian bookworm-updates/main Translation-en.diff/Index [15.1 kB]
Ign:7 http://deb.debian.org/debian bookworm-updates/main Translation-en.diff/Index
Get:8 http://deb.debian.org/debian bookworm-updates/non-free Sources [1544 B]
Get:9 http://deb.debian.org/debian bookworm-updates/contrib Sources [776 B]
Get:10 http://deb.debian.org/debian bookworm-updates/contrib Translation-en [408 B]
Get:11 http://deb.debian.org/debian bookworm-updates/non-free Translation-en [7744 B]
Get:12 http://deb.debian.org/debian bookworm-updates/non-free-firmware Translation-en [384 B]
Get:13 http://deb.debian.org/debian bookworm-updates/main Sources [16.2 kB]
Get:14 http://deb.debian.org/debian bookworm-updates/main armel Packages [11.3 kB]
Get:15 http://deb.debian.org/debian bookworm-updates/main Translation-en [16.0 kB]
Get:16 http://ftp.us.debian.org/debian bookworm/contrib Sources [51.4 kB]
Get:17 http://ftp.us.debian.org/debian bookworm/non-free Sources [77.9 kB]
Get:18 http://ftp.us.debian.org/debian bookworm/main Sources [9495 kB]
Get:19 http://ftp.us.debian.org/debian bookworm/non-free-firmware Sources [6440 B]
Get:20 http://ftp.us.debian.org/debian bookworm/main armel Packages [8453 kB]
Get:21 https://security.debian.org/debian-security bookworm-security/main armel Packages [226 kB]
Get:22 https://security.debian.org/debian-security bookworm-security/main Translation-en [147 kB]
Get:23 https://security.debian.org/debian-security bookworm-security/contrib Translation-en [652 B]
Get:24 http://ftp.us.debian.org/debian bookworm/main Translation-en [6109 kB]
Get:25 http://ftp.us.debian.org/debian bookworm/contrib armel Packages [39.7 kB]
Get:26 http://ftp.us.debian.org/debian bookworm/contrib Translation-en [48.8 kB]
Get:27 http://ftp.us.debian.org/debian bookworm/non-free Translation-en [67.0 kB]
Get:28 http://ftp.us.debian.org/debian bookworm/non-free-firmware Translation-en [20.9 kB]
Fetched 25.1 MB in 2min 16s (185 kB/s)
root@debian:~# lists... Done
Get:23 https://security.debian.org/debian-security bookworm-security/c^C
root@debian:~# ^C
root@debian:~# apt-get upgrade
Reading package lists... Done
Building dependency tree... Done
Reading state information... Done
Calculating upgrade... Done
The following packages were automatically installed and are no longer required:
bind9-host bind9-libs libbpf0 libcbor0 libdns-export1110 libevent-2.1-7
libffi7 libfstrm0 libicu67 libicu72 libisc-export1105 libjemalloc2
libjson-c5 libldap-2.4-2 liblmdb0 libmaxminddb0 libncurses6 libnghttp2-14
libopts25 libpcre3 libprocps8 libprotobuf-c1 libssl1.1 libuv1 libxml2
Use 'apt autoremove' to remove them.
The following packages will be upgraded:
avahi-daemon base-files bash bind9-host bind9-libs bsdextrautils bsdutils
initramfs-tools initramfs-tools-core iputils-ping libavahi-common-data
libavahi-common3 libavahi-core7 libblkid1 libc-bin libc6 libexpat1
libgnutls30 libgssapi-krb5-2 libk5crypto3 libkrb5-3 libkrb5support0
libmount1 libnfsidmap1 libnghttp2-14 libperl5.36 libpython3.11-minimal
libpython3.11-stdlib libseccomp2 libsmartcols1 libsqlite3-0 libssl3
libsystemd0 libtasn1-6 libudev1 libuuid1 libuv1 mount nano nfs-common
nfs-kernel-server openssh-client openssh-server openssh-sftp-server openssl
perl perl-base perl-modules-5.36 python3.11 python3.11-minimal rsync tar
tzdata u-boot-tools ucf udev usrmerge util-linux util-linux-extra vim-common
vim-tiny wget xxd
63 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
Need to get 34.0 MB of archives.
After this operation, 3927 kB disk space will be freed.
Do you want to continue? [Y/n] Y
Get:1 http://ftp.us.debian.org/debian bookworm/main armel base-files armel 12.4+deb12u10 [70.9 kB]
Get:2 http://ftp.us.debian.org/debian bookworm/main armel bash armel 5.2.15-2+b7 [1412 kB]
Get:3 http://ftp.us.debian.org/debian bookworm/main armel bsdutils armel 1:2.38.1-5+deb12u3 [86.7 kB]
Get:4 http://ftp.us.debian.org/debian bookworm/main armel libperl5.36 armel 5.36.0-7+deb12u1 [3454 kB]
Get:5 http://ftp.us.debian.org/debian bookworm/main armel perl armel 5.36.0-7+deb12u1 [239 kB]
Get:6 http://ftp.us.debian.org/debian bookworm/main armel perl-base armel 5.36.0-7+deb12u1 [1439 kB]
Get:7 http://ftp.us.debian.org/debian bookworm/main armel perl-modules-5.36 all 5.36.0-7+deb12u1 [2815 kB]
Get:8 http://ftp.us.debian.org/debian bookworm/main armel libc6 armel 2.36-9+deb12u10 [2145 kB]
Get:9 http://ftp.us.debian.org/debian bookworm/main armel tar armel 1.34+dfsg-1.2+deb12u1 [805 kB]
Get:10 http://ftp.us.debian.org/debian bookworm/main armel libsmartcols1 armel 2.38.1-5+deb12u3 [93.0 kB]
Get:11 http://ftp.us.debian.org/debian bookworm/main armel util-linux-extra armel 2.38.1-5+deb12u3 [101 kB]
Get:12 http://ftp.us.debian.org/debian bookworm/main armel util-linux armel 2.38.1-5+deb12u3 [1077 kB]
Get:13 http://ftp.us.debian.org/debian bookworm/main armel libc-bin armel 2.36-9+deb12u10 [495 kB]
Get:14 http://ftp.us.debian.org/debian bookworm/main armel mount armel 2.38.1-5+deb12u3 [125 kB]
Get:15 http://ftp.us.debian.org/debian bookworm/main armel libblkid1 armel 2.38.1-5+deb12u3 [133 kB]
Get:16 http://ftp.us.debian.org/debian bookworm/main armel libsqlite3-0 armel 3.40.1-2+deb12u1 [729 kB]
Get:17 http://ftp.us.debian.org/debian bookworm/main armel libuuid1 armel 2.38.1-5+deb12u3 [27.5 kB]
Get:18 http://ftp.us.debian.org/debian bookworm/main armel ucf all 3.0043+nmu1+deb12u1 [55.3 kB]
Get:19 http://ftp.us.debian.org/debian bookworm/main armel nfs-kernel-server armel 1:2.6.2-4+deb12u1 [133 kB]
Get:20 http://ftp.us.debian.org/debian bookworm/main armel libgssapi-krb5-2 armel 1.20.1-2+deb12u2 [111 kB]
Get:21 http://ftp.us.debian.org/debian bookworm/main armel libkrb5-3 armel 1.20.1-2+deb12u2 [284 kB]
Get:22 http://ftp.us.debian.org/debian bookworm/main armel libkrb5support0 armel 1.20.1-2+deb12u2 [29.5 kB]
Get:23 http://ftp.us.debian.org/debian bookworm/main armel libk5crypto3 armel 1.20.1-2+deb12u2 [74.3 kB]
Get:24 http://ftp.us.debian.org/debian bookworm/main armel libssl3 armel 3.0.15-1~deb12u1 [1636 kB]
Get:25 http://ftp.us.debian.org/debian bookworm/main armel libmount1 armel 2.38.1-5+deb12u3 [145 kB]
Get:26 http://ftp.us.debian.org/debian bookworm/main armel nfs-common armel 1:2.6.2-4+deb12u1 [232 kB]
Get:27 http://ftp.us.debian.org/debian bookworm/main armel libnfsidmap1 armel 1:2.6.2-4+deb12u1 [47.2 kB]
Get:28 http://ftp.us.debian.org/debian bookworm/main armel openssh-sftp-server armel 1:9.2p1-2+deb12u5 [57.1 kB]
Get:29 http://ftp.us.debian.org/debian bookworm/main armel openssh-server armel 1:9.2p1-2+deb12u5 [402 kB]
Get:30 http://ftp.us.debian.org/debian bookworm/main armel openssh-client armel 1:9.2p1-2+deb12u5 [863 kB]
Get:31 http://ftp.us.debian.org/debian bookworm/main armel libsystemd0 armel 252.36-1~deb12u1 [299 kB]
Get:32 http://ftp.us.debian.org/debian bookworm/main armel python3.11 armel 3.11.2-6+deb12u5 [573 kB]
Get:33 http://ftp.us.debian.org/debian bookworm/main armel libpython3.11-stdlib armel 3.11.2-6+deb12u5 [1675 kB]
Get:34 http://ftp.us.debian.org/debian bookworm/main armel python3.11-minimal armel 3.11.2-6+deb12u5 [1692 kB]
Get:35 http://ftp.us.debian.org/debian bookworm/main armel libpython3.11-minimal armel 3.11.2-6+deb12u5 [801 kB]
Get:36 http://ftp.us.debian.org/debian bookworm/main armel libexpat1 armel 2.5.0-1+deb12u1 [77.6 kB]
Get:37 http://ftp.us.debian.org/debian bookworm/main armel rsync armel 3.2.7-1+deb12u2 [394 kB]
Get:38 http://ftp.us.debian.org/debian bookworm/main armel libtasn1-6 armel 4.19.0-2+deb12u1 [42.6 kB]
Get:39 http://ftp.us.debian.org/debian bookworm/main armel libgnutls30 armel 3.7.9-2+deb12u4 [1309 kB]
Get:40 http://ftp.us.debian.org/debian bookworm/main armel libseccomp2 armel 2.5.4-1+deb12u1 [45.9 kB]
Get:41 http://ftp.us.debian.org/debian bookworm/main armel udev armel 252.36-1~deb12u1 [1645 kB]
Get:42 http://ftp.us.debian.org/debian bookworm/main armel libudev1 armel 252.36-1~deb12u1 [100 kB]
Get:43 http://ftp.us.debian.org/debian bookworm/main armel usrmerge all 37~deb12u1 [13.3 kB]
Get:44 http://ftp.us.debian.org/debian bookworm/main armel tzdata all 2025a-0+deb12u1 [299 kB]
Get:45 http://ftp.us.debian.org/debian bookworm/main armel iputils-ping armel 3:20221126-1+deb12u1 [46.0 kB]
Get:46 http://ftp.us.debian.org/debian bookworm/main armel nano armel 7.2-1+deb12u1 [673 kB]
Get:47 http://ftp.us.debian.org/debian bookworm/main armel vim-tiny armel 2:9.0.1378-2+deb12u2 [612 kB]
Get:48 http://ftp.us.debian.org/debian bookworm/main armel xxd armel 2:9.0.1378-2+deb12u2 [83.5 kB]
Get:49 http://ftp.us.debian.org/debian bookworm/main armel vim-common all 2:9.0.1378-2+deb12u2 [125 kB]
Get:50 http://ftp.us.debian.org/debian bookworm/main armel libuv1 armel 1.44.2-1+deb12u1 [123 kB]
Get:51 http://ftp.us.debian.org/debian bookworm/main armel libnghttp2-14 armel 1.52.0-1+deb12u2 [62.1 kB]
Get:52 http://ftp.us.debian.org/debian bookworm/main armel bind9-host armel 1:9.18.33-1~deb12u2 [51.9 kB]
Get:53 http://ftp.us.debian.org/debian bookworm/main armel bind9-libs armel 1:9.18.33-1~deb12u2 [1023 kB]
Get:54 http://ftp.us.debian.org/debian bookworm/main armel wget armel 1.21.3-1+deb12u1 [912 kB]
Get:55 http://ftp.us.debian.org/debian bookworm/main armel avahi-daemon armel 0.8-10+deb12u1 [75.7 kB]
Get:56 http://ftp.us.debian.org/debian bookworm/main armel libavahi-core7 armel 0.8-10+deb12u1 [90.5 kB]
Get:57 http://ftp.us.debian.org/debian bookworm/main armel libavahi-common3 armel 0.8-10+deb12u1 [40.1 kB]
Get:58 http://ftp.us.debian.org/debian bookworm/main armel libavahi-common-data armel 0.8-10+deb12u1 [107 kB]
Get:59 http://ftp.us.debian.org/debian bookworm/main armel bsdextrautils armel 2.38.1-5+deb12u3 [79.7 kB]
Get:60 http://ftp.us.debian.org/debian bookworm/main armel initramfs-tools all 0.142+deb12u1 [15.8 kB]
Get:61 http://ftp.us.debian.org/debian bookworm/main armel initramfs-tools-core all 0.142+deb12u1 [47.9 kB]
Get:62 http://ftp.us.debian.org/debian bookworm/main armel openssl armel 3.0.15-1~deb12u1 [1387 kB]
Get:63 http://ftp.us.debian.org/debian bookworm/main armel u-boot-tools armel 2023.01+dfsg-2+deb12u1 [175 kB]
Fetched 34.0 MB in 5s (6203 kB/s)
Extracting templates from packages: 100%
Preconfiguring packages ...
(Reading database ... 16901 files and directories currently installed.)
Preparing to unpack .../base-files_12.4+deb12u10_armel.deb ...
Unpacking base-files (12.4+deb12u10) over (12.4+deb12u2) ...
Setting up base-files (12.4+deb12u10) ...
Installing new version of config file /etc/debian_version ...
(Reading database ... 16901 files and directories currently installed.)
Preparing to unpack .../bash_5.2.15-2+b7_armel.deb ...
Unpacking bash (5.2.15-2+b7) over (5.2.15-2+b2) ...
Setting up bash (5.2.15-2+b7) ...
update-alternatives: using /usr/share/man/man7/bash-builtins.7.gz to provide /usr/share/man/man7/builtins.7.gz (builtins.7.gz) in auto mode
(Reading database ... 16901 files and directories currently installed.)
Preparing to unpack .../bsdutils_1%3a2.38.1-5+deb12u3_armel.deb ...
Unpacking bsdutils (1:2.38.1-5+deb12u3) over (1:2.38.1-5+b1) ...
Setting up bsdutils (1:2.38.1-5+deb12u3) ...
(Reading database ... 16900 files and directories currently installed.)
Preparing to unpack .../libperl5.36_5.36.0-7+deb12u1_armel.deb ...
Unpacking libperl5.36:armel (5.36.0-7+deb12u1) over (5.36.0-7) ...
Preparing to unpack .../perl_5.36.0-7+deb12u1_armel.deb ...
Unpacking perl (5.36.0-7+deb12u1) over (5.36.0-7) ...
Preparing to unpack .../perl-base_5.36.0-7+deb12u1_armel.deb ...
Unpacking perl-base (5.36.0-7+deb12u1) over (5.36.0-7) ...
Setting up perl-base (5.36.0-7+deb12u1) ...
(Reading database ... 16900 files and directories currently installed.)
Preparing to unpack .../perl-modules-5.36_5.36.0-7+deb12u1_all.deb ...
Unpacking perl-modules-5.36 (5.36.0-7+deb12u1) over (5.36.0-7) ...
Preparing to unpack .../libc6_2.36-9+deb12u10_armel.deb ...
Unpacking libc6:armel (2.36-9+deb12u10) over (2.36-9+deb12u3) ...
Setting up libc6:armel (2.36-9+deb12u10) ...
INIT: version 3.06 reloading
(Reading database ... 16900 files and directories currently installed.)
Preparing to unpack .../tar_1.34+dfsg-1.2+deb12u1_armel.deb ...
Unpacking tar (1.34+dfsg-1.2+deb12u1) over (1.34+dfsg-1.2) ...
Setting up tar (1.34+dfsg-1.2+deb12u1) ...
(Reading database ... 16900 files and directories currently installed.)
Preparing to unpack .../libsmartcols1_2.38.1-5+deb12u3_armel.deb ...
Unpacking libsmartcols1:armel (2.38.1-5+deb12u3) over (2.38.1-5+b1) ...
Setting up libsmartcols1:armel (2.38.1-5+deb12u3) ...
(Reading database ... 16899 files and directories currently installed.)
Preparing to unpack .../util-linux-extra_2.38.1-5+deb12u3_armel.deb ...
Unpacking util-linux-extra (2.38.1-5+deb12u3) over (2.38.1-5+b1) ...
Setting up util-linux-extra (2.38.1-5+deb12u3) ...
(Reading database ... 16898 files and directories currently installed.)
Preparing to unpack .../util-linux_2.38.1-5+deb12u3_armel.deb ...
Unpacking util-linux (2.38.1-5+deb12u3) over (2.38.1-5+b1) ...
Setting up util-linux (2.38.1-5+deb12u3) ...
(Reading database ... 16897 files and directories currently installed.)
Preparing to unpack .../libc-bin_2.36-9+deb12u10_armel.deb ...
Unpacking libc-bin (2.36-9+deb12u10) over (2.36-9+deb12u3) ...
Setting up libc-bin (2.36-9+deb12u10) ...
(Reading database ... 16897 files and directories currently installed.)
Preparing to unpack .../mount_2.38.1-5+deb12u3_armel.deb ...
Unpacking mount (2.38.1-5+deb12u3) over (2.38.1-5+b1) ...
Preparing to unpack .../libblkid1_2.38.1-5+deb12u3_armel.deb ...
Unpacking libblkid1:armel (2.38.1-5+deb12u3) over (2.38.1-5+b1) ...
Setting up libblkid1:armel (2.38.1-5+deb12u3) ...
(Reading database ... 16895 files and directories currently installed.)
Preparing to unpack .../libsqlite3-0_3.40.1-2+deb12u1_armel.deb ...
Unpacking libsqlite3-0:armel (3.40.1-2+deb12u1) over (3.40.1-2) ...
Preparing to unpack .../libuuid1_2.38.1-5+deb12u3_armel.deb ...
Unpacking libuuid1:armel (2.38.1-5+deb12u3) over (2.38.1-5+b1) ...
Setting up libuuid1:armel (2.38.1-5+deb12u3) ...
(Reading database ... 16894 files and directories currently installed.)
Preparing to unpack .../0-ucf_3.0043+nmu1+deb12u1_all.deb ...
Unpacking ucf (3.0043+nmu1+deb12u1) over (3.0043+nmu1) ...
Preparing to unpack .../1-nfs-kernel-server_1%3a2.6.2-4+deb12u1_armel.deb ...
Unpacking nfs-kernel-server (1:2.6.2-4+deb12u1) over (1:2.6.2-4) ...
Preparing to unpack .../2-libgssapi-krb5-2_1.20.1-2+deb12u2_armel.deb ...
Unpacking libgssapi-krb5-2:armel (1.20.1-2+deb12u2) over (1.20.1-2+deb12u1) ...
Preparing to unpack .../3-libkrb5-3_1.20.1-2+deb12u2_armel.deb ...
Unpacking libkrb5-3:armel (1.20.1-2+deb12u2) over (1.20.1-2+deb12u1) ...
Preparing to unpack .../4-libkrb5support0_1.20.1-2+deb12u2_armel.deb ...
Unpacking libkrb5support0:armel (1.20.1-2+deb12u2) over (1.20.1-2+deb12u1) ...
Preparing to unpack .../5-libk5crypto3_1.20.1-2+deb12u2_armel.deb ...
Unpacking libk5crypto3:armel (1.20.1-2+deb12u2) over (1.20.1-2+deb12u1) ...
Preparing to unpack .../6-libssl3_3.0.15-1~deb12u1_armel.deb ...
Unpacking libssl3:armel (3.0.15-1~deb12u1) over (3.0.11-1~deb12u2) ...
Preparing to unpack .../7-libmount1_2.38.1-5+deb12u3_armel.deb ...
Unpacking libmount1:armel (2.38.1-5+deb12u3) over (2.38.1-5+b1) ...
Setting up libmount1:armel (2.38.1-5+deb12u3) ...
(Reading database ... 16893 files and directories currently installed.)
Preparing to unpack .../0-nfs-common_1%3a2.6.2-4+deb12u1_armel.deb ...
Unpacking nfs-common (1:2.6.2-4+deb12u1) over (1:2.6.2-4) ...
Preparing to unpack .../1-libnfsidmap1_1%3a2.6.2-4+deb12u1_armel.deb ...
Unpacking libnfsidmap1:armel (1:2.6.2-4+deb12u1) over (1:2.6.2-4) ...
Preparing to unpack .../2-openssh-sftp-server_1%3a9.2p1-2+deb12u5_armel.deb ...
Unpacking openssh-sftp-server (1:9.2p1-2+deb12u5) over (1:9.2p1-2+deb12u1) ...
Preparing to unpack .../3-openssh-server_1%3a9.2p1-2+deb12u5_armel.deb ...
Unpacking openssh-server (1:9.2p1-2+deb12u5) over (1:9.2p1-2+deb12u1) ...
Preparing to unpack .../4-openssh-client_1%3a9.2p1-2+deb12u5_armel.deb ...
Unpacking openssh-client (1:9.2p1-2+deb12u5) over (1:9.2p1-2+deb12u1) ...
Preparing to unpack .../5-libsystemd0_252.36-1~deb12u1_armel.deb ...
Unpacking libsystemd0:armel (252.36-1~deb12u1) over (252.17-1~deb12u1) ...
Setting up libsystemd0:armel (252.36-1~deb12u1) ...
(Reading database ... 16893 files and directories currently installed.)
Preparing to unpack .../0-python3.11_3.11.2-6+deb12u5_armel.deb ...
Unpacking python3.11 (3.11.2-6+deb12u5) over (3.11.2-6) ...
Preparing to unpack .../1-libpython3.11-stdlib_3.11.2-6+deb12u5_armel.deb ...
Unpacking libpython3.11-stdlib:armel (3.11.2-6+deb12u5) over (3.11.2-6) ...
Preparing to unpack .../2-python3.11-minimal_3.11.2-6+deb12u5_armel.deb ...
Unpacking python3.11-minimal (3.11.2-6+deb12u5) over (3.11.2-6) ...
Preparing to unpack .../3-libpython3.11-minimal_3.11.2-6+deb12u5_armel.deb ...
Unpacking libpython3.11-minimal:armel (3.11.2-6+deb12u5) over (3.11.2-6) ...
Preparing to unpack .../4-libexpat1_2.5.0-1+deb12u1_armel.deb ...
Unpacking libexpat1:armel (2.5.0-1+deb12u1) over (2.5.0-1) ...
Preparing to unpack .../5-rsync_3.2.7-1+deb12u2_armel.deb ...
Unpacking rsync (3.2.7-1+deb12u2) over (3.2.7-1) ...
Preparing to unpack .../6-libtasn1-6_4.19.0-2+deb12u1_armel.deb ...
Unpacking libtasn1-6:armel (4.19.0-2+deb12u1) over (4.19.0-2) ...
Setting up libtasn1-6:armel (4.19.0-2+deb12u1) ...
(Reading database ... 16893 files and directories currently installed.)
Preparing to unpack .../libgnutls30_3.7.9-2+deb12u4_armel.deb ...
Unpacking libgnutls30:armel (3.7.9-2+deb12u4) over (3.7.9-2) ...
Setting up libgnutls30:armel (3.7.9-2+deb12u4) ...
(Reading database ... 16893 files and directories currently installed.)
Preparing to unpack .../libseccomp2_2.5.4-1+deb12u1_armel.deb ...
Unpacking libseccomp2:armel (2.5.4-1+deb12u1) over (2.5.4-1+b3) ...
Setting up libseccomp2:armel (2.5.4-1+deb12u1) ...
(Reading database ... 16892 files and directories currently installed.)
Preparing to unpack .../udev_252.36-1~deb12u1_armel.deb ...
Unpacking udev (252.36-1~deb12u1) over (252.17-1~deb12u1) ...
Preparing to unpack .../libudev1_252.36-1~deb12u1_armel.deb ...
Unpacking libudev1:armel (252.36-1~deb12u1) over (252.17-1~deb12u1) ...
Setting up libudev1:armel (252.36-1~deb12u1) ...
(Reading database ... 16893 files and directories currently installed.)
Preparing to unpack .../usrmerge_37~deb12u1_all.deb ...
Unpacking usrmerge (37~deb12u1) over (35) ...
Setting up perl-modules-5.36 (5.36.0-7+deb12u1) ...
Setting up libperl5.36:armel (5.36.0-7+deb12u1) ...
Setting up perl (5.36.0-7+deb12u1) ...
Setting up usrmerge (37~deb12u1) ...
(Reading database ... 16893 files and directories currently installed.)
Preparing to unpack .../00-tzdata_2025a-0+deb12u1_all.deb ...
Unpacking tzdata (2025a-0+deb12u1) over (2023c-5) ...
Preparing to unpack .../01-iputils-ping_3%3a20221126-1+deb12u1_armel.deb ...
Unpacking iputils-ping (3:20221126-1+deb12u1) over (3:20221126-1) ...
Preparing to unpack .../02-nano_7.2-1+deb12u1_armel.deb ...
Unpacking nano (7.2-1+deb12u1) over (7.2-1) ...
Preparing to unpack .../03-vim-tiny_2%3a9.0.1378-2+deb12u2_armel.deb ...
Unpacking vim-tiny (2:9.0.1378-2+deb12u2) over (2:9.0.1378-2) ...
Preparing to unpack .../04-xxd_2%3a9.0.1378-2+deb12u2_armel.deb ...
Unpacking xxd (2:9.0.1378-2+deb12u2) over (2:9.0.1378-2) ...
Preparing to unpack .../05-vim-common_2%3a9.0.1378-2+deb12u2_all.deb ...
Unpacking vim-common (2:9.0.1378-2+deb12u2) over (2:9.0.1378-2) ...
Preparing to unpack .../06-libuv1_1.44.2-1+deb12u1_armel.deb ...
Unpacking libuv1:armel (1.44.2-1+deb12u1) over (1.44.2-1) ...
Preparing to unpack .../07-libnghttp2-14_1.52.0-1+deb12u2_armel.deb ...
Unpacking libnghttp2-14:armel (1.52.0-1+deb12u2) over (1.52.0-1) ...
Preparing to unpack .../08-bind9-host_1%3a9.18.33-1~deb12u2_armel.deb ...
Unpacking bind9-host (1:9.18.33-1~deb12u2) over (1:9.18.19-1~deb12u1) ...
Preparing to unpack .../09-bind9-libs_1%3a9.18.33-1~deb12u2_armel.deb ...
Unpacking bind9-libs:armel (1:9.18.33-1~deb12u2) over (1:9.18.19-1~deb12u1) ...
Preparing to unpack .../10-wget_1.21.3-1+deb12u1_armel.deb ...
Unpacking wget (1.21.3-1+deb12u1) over (1.21.3-1+b1) ...
Preparing to unpack .../11-avahi-daemon_0.8-10+deb12u1_armel.deb ...
Unpacking avahi-daemon (0.8-10+deb12u1) over (0.8-10) ...
Preparing to unpack .../12-libavahi-core7_0.8-10+deb12u1_armel.deb ...
Unpacking libavahi-core7:armel (0.8-10+deb12u1) over (0.8-10) ...
Preparing to unpack .../13-libavahi-common3_0.8-10+deb12u1_armel.deb ...
Unpacking libavahi-common3:armel (0.8-10+deb12u1) over (0.8-10) ...
Preparing to unpack .../14-libavahi-common-data_0.8-10+deb12u1_armel.deb ...
Unpacking libavahi-common-data:armel (0.8-10+deb12u1) over (0.8-10) ...
Preparing to unpack .../15-bsdextrautils_2.38.1-5+deb12u3_armel.deb ...
Unpacking bsdextrautils (2.38.1-5+deb12u3) over (2.38.1-5+b1) ...
Preparing to unpack .../16-initramfs-tools_0.142+deb12u1_all.deb ...
Unpacking initramfs-tools (0.142+deb12u1) over (0.142) ...
Preparing to unpack .../17-initramfs-tools-core_0.142+deb12u1_all.deb ...
Unpacking initramfs-tools-core (0.142+deb12u1) over (0.142) ...
Preparing to unpack .../18-openssl_3.0.15-1~deb12u1_armel.deb ...
Unpacking openssl (3.0.15-1~deb12u1) over (3.0.11-1~deb12u2) ...
Preparing to unpack .../19-u-boot-tools_2023.01+dfsg-2+deb12u1_armel.deb ...
Unpacking u-boot-tools (2023.01+dfsg-2+deb12u1) over (2023.01+dfsg-2) ...
Setting up libexpat1:armel (2.5.0-1+deb12u1) ...
Setting up libnfsidmap1:armel (1:2.6.2-4+deb12u1) ...
Setting up bsdextrautils (2.38.1-5+deb12u3) ...
Setting up wget (1.21.3-1+deb12u1) ...
Setting up libsqlite3-0:armel (3.40.1-2+deb12u1) ...
Setting up libssl3:armel (3.0.15-1~deb12u1) ...
Setting up libnghttp2-14:armel (1.52.0-1+deb12u2) ...
Setting up xxd (2:9.0.1378-2+deb12u2) ...
Setting up libkrb5support0:armel (1.20.1-2+deb12u2) ...
Setting up tzdata (2025a-0+deb12u1) ...

Current default time zone: 'America/Los_Angeles'
Local time is now: Sun Mar 16 14:38:55 PDT 2025.
Universal Time is now: Sun Mar 16 21:38:55 UTC 2025.
Run 'dpkg-reconfigure tzdata' if you wish to change it.

Setting up libuv1:armel (1.44.2-1+deb12u1) ...
Setting up vim-common (2:9.0.1378-2+deb12u2) ...
Setting up libavahi-common-data:armel (0.8-10+deb12u1) ...
Setting up udev (252.36-1~deb12u1) ...
Stopping hotplug events dispatcher: systemd-udevd.
Starting hotplug events dispatcher: systemd-udevd.
Setting up ucf (3.0043+nmu1+deb12u1) ...
Setting up libk5crypto3:armel (1.20.1-2+deb12u2) ...
Setting up nano (7.2-1+deb12u1) ...
Installing new version of config file /etc/nanorc ...
Setting up u-boot-tools (2023.01+dfsg-2+deb12u1) ...
Setting up mount (2.38.1-5+deb12u3) ...
Setting up libkrb5-3:armel (1.20.1-2+deb12u2) ...
Setting up libpython3.11-minimal:armel (3.11.2-6+deb12u5) ...
Setting up initramfs-tools-core (0.142+deb12u1) ...
Setting up openssl (3.0.15-1~deb12u1) ...
Setting up iputils-ping (3:20221126-1+deb12u1) ...
Setting up rsync (3.2.7-1+deb12u2) ...
Setting up python3.11-minimal (3.11.2-6+deb12u5) ...
Setting up initramfs-tools (0.142+deb12u1) ...
update-initramfs: deferring update (trigger activated)
Setting up libpython3.11-stdlib:armel (3.11.2-6+deb12u5) ...
Setting up libavahi-common3:armel (0.8-10+deb12u1) ...
Setting up vim-tiny (2:9.0.1378-2+deb12u2) ...
Setting up libgssapi-krb5-2:armel (1.20.1-2+deb12u2) ...
Setting up libavahi-core7:armel (0.8-10+deb12u1) ...
Setting up python3.11 (3.11.2-6+deb12u5) ...
Setting up bind9-libs:armel (1:9.18.33-1~deb12u2) ...
Setting up openssh-client (1:9.2p1-2+deb12u5) ...
Setting up nfs-common (1:2.6.2-4+deb12u1) ...
Stopping NFS common utilities: idmapd statd.
Starting NFS common utilities: statd idmapd.
Setting up avahi-daemon (0.8-10+deb12u1) ...
Reloading system message bus config...done.
Setting up bind9-host (1:9.18.33-1~deb12u2) ...
Setting up openssh-sftp-server (1:9.2p1-2+deb12u5) ...
Setting up nfs-kernel-server (1:2.6.2-4+deb12u1) ...
Stopping NFS kernel daemon: mountd nfsd.
Unexporting directories for NFS kernel daemon...done.
Not starting NFS kernel daemon: no exports ... (warning).
Setting up openssh-server (1:9.2p1-2+deb12u5) ...
Restarting OpenBSD Secure Shell server: sshd.
Processing triggers for man-db (2.11.2-2) ...
Processing triggers for dbus (1.14.10-1~deb12u1) ...
Processing triggers for ntpsec (1.2.2+dfsg1-1+deb12u1) ...
Stopping NTP server: ntpd.
Starting NTP server: ntpd2025-03-16T14:43:07 ntpd[3659]: INIT: ntpd ntpsec-1.2.2: Starting
2025-03-16T14:43:07 ntpd[3659]: INIT: Command line: /usr/sbin/ntpd -p /run/ntpd.pid -g -N -c /run/ntpsec/ntp.conf.dhcp -u ntpsec:ntpsec
.
Processing triggers for debianutils (5.7-0.5~deb12u1) ...
Procesebian:/boot# mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-6.5.7-kirkwood-tld-1 -d initrd.img-6.5.7-kirkwood-tld-1 uInitrd
Image Name: initramfs-6.5.7-kirkwood-tld-1
Created: Sun Mar 16 14:46:38 2025tld-1 -d initrd.img-6.5.7-kirkwood-tld-1 uI
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5798575 Bytes = 5662.67 KiB = 5.53 MiB
Load Address: 00000000
Entry Point: 00000000
root@debian:/boot# dpkg-reconfigure tzdata
Package configuration
lqqqqqqqqqqqqqqqqqqqqqqqqqqqConfiguring tzdataqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqkqq
x Please select the geographic area in which you live. Subsequent x
x configuration questions will narrow this down by presenting a list of x
x cities, representing the time zones in which they are located. x
x x
x Geographic area: x
x lqqqq-(-)qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk x
x x Arctic Ocean x x
x x Asia x x
x x Atlantic Ocean x x
x x Australia x x
x x Europe x x
x x Indian Ocean x x
x x Pacific Ocean x x
x x US x x
x x None of the above x x
x mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq100%qqqqj x
tqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqu
x < OK > <Cancel> x
mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj
































































Package configuration
qqlqqqqqqqqqqqqqqqqqqqqqqqqqConfiguring tzdataqqqqqqqqqqqqqqqqqqqqqqqqqqqkqqqq
x Please select the city or region corresponding to your time zone. x
x x
x Time zone: x
x lqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk x
x x Amsterdam x x
x x Andorra x x
x x Astrakhan x x
x x Athens x x
x x Belfast x x
x x Belgrade x x
x x Berlin x x
x x Bratislava x x
x x Brussels x x
x x Bucharest x x
x x Budapest x x
x mqqqq.(+)qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq18%qqqqqj x
tqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqu
x < OK > <Cancel> x
mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj



Current default time zone: 'Europe/Berlin'
Local time is now: Sun Mar 16 22:47:27 CET 2025.
Universal Time is now: Sun Mar 16 21:47:27 UTC 2025.

root@debian:/boot# cd --
root@debian:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether aa:00:00:00:00:01 brd ff:ff:ff:ff:ff:ff
inet 192.168.178.78/24 brd 192.168.178.255 scope global dynamic eth0
valid_lft 860182sec preferred_lft 860182sec
inet6 fdcf:e8d9:2235:0:a800:ff:fe00:1/64 scope global dynamic mngtmpaddr
valid_lft 6974sec preferred_lft 3374sec
inet6 2001:9e8:5a7b:6800:a800:ff:fe00:1/64 scope global dynamic mngtmpaddr
valid_lft 6974sec preferred_lft 3374sec
inet6 fe80::a800:ff:fe00:1/64 scope link
valid_lft forever preferred_lft forever
root@debian:~#