Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package March 19, 2018 06:40PM |
Registered: 6 years ago Posts: 18 |
> PCI-E0 uses external clock source. > PCIe: Port[0] Enable PCIe LTSSM > PCIe: Port[0] Check data link layer... > > > > Device not found. >
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package March 19, 2018 06:59PM |
Registered: 6 years ago Posts: 42 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package March 20, 2018 04:02PM |
Registered: 10 years ago Posts: 46 |
Whitney # setenv bootargs 'console=ttyS0,38400 mem=512M@0x20000000 root=/dev/sda1';setenv loaduimage 'ext2load scsi 0 0x28000000 /boot/uImage';setenv bootcmd_scsi 'scsi init;run loaduimage;bootm 0x28000000' Whitney # run bootcmd_scsi Initialize SCSI AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl SATA mode flags: ncq stag pm led clo only pmp pio slum part set feature error! scanning bus for devices... Supprt LBA48 addressing. timeout exit! Device 0: (1:0) Vendor: ATA Prod.: HGST HTS725050A7 Rev: GH2Z Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) 3019912 bytes read enter do_eth_down!!! ## Booting kernel from Legacy Image at 28000000 ... Image Name: Linux-4.4.121-tommy Created: 2018-03-18 23:01:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3019848 Bytes = 2.9 MB Load Address: 22000000 Entry Point: 22000000 Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x900 Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 4.4.121-tommy (root@debian9) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #26 SMP Sun Mar 18 23:57:36 CET 2018 CPU: ARMv6-compatible processor [410fb024] revision 4 (ARMv7), cr=00c5787d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Seagate CNS3420 NAS Memory policy: Data cache writealloc PERCPU: Embedded 12 pages/cpu @dfbd9000 s17004 r8192 d23956 u49152 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyS0,38400 mem=512M@0x20000000 root=/dev/sda1 PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 513692K/524288K available (4211K kernel code, 159K rwdata, 1256K rodata, 212K init, 101K bss, 10596K reserved, 0K cma-reserved) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc055ef9c (5468 kB) .init : 0xc055f000 - 0xc0594000 ( 212 kB) .data : 0xc0594000 - 0xc05bbe10 ( 160 kB) .bss : 0xc05bbe10 - 0xc05d5348 ( 102 kB) Hierarchical RCU implementation. Build-time adjustment of leaf fanout to 32. NR_IRQS:16 nr_irqs:16 16 clocksource: freerun: mask: 0xffffffffffff max_cycles: 0x179dd7f66, max_idle_ns: 28210892933900 ns smp_twd: clock not found -2 sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns Console: colour dummy device 80x30 console [ttyS0] enabled Calibrating local timer... 347.99MHz. Calibrating delay loop... 277.70 BogoMIPS (lpj=1388544) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) Initializing cgroup subsys io Initializing cgroup subsys devices Initializing cgroup subsys net_cls CPU: Testing write buffer coherency: ok Setting up static identity map for 0x200082a0 - 0x200082fc Brought up 2 CPUs SMP: Total of 2 processors activated (555.41 BogoMIPS). devtmpfs: initialized VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 2, 16384 bytes) NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor ladder cpuidle: using governor menu L2C: DT/platform modifies aux control register: 0x02040000 -> 0x02540000 L2C-310 cache controller enabled, 8 ways, 256 kB L2C-310: CACHE_ID 0x410000c4, AUX_CTRL 0x06540000 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb clocksource: Switched to clocksource freerun FS-Cache: Loaded NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler deadline registered (default) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x78000000 (irq = 45, base_baud = 1500000) is a 16550A loop: module loaded mGine mflash driver, (c) 2008 mGine Co. zram: Added device: zram0 ahci ahci.0: SSS flag set, parallel bus scan disabled ahci ahci.0: AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl platform mode ahci ahci.0: flags: ncq sntf stag pm led clo only pmp pio slum part ccc scsi host0: ahci scsi host1: ahci ata1: SATA max UDMA/133 mmio [mem 0x83000000-0x83ffffff] port 0x100 irq 65 ata2: SATA max UDMA/133 mmio [mem 0x83000000-0x83ffffff] port 0x180 irq 65 physmap platform flash device: 08000000 at 10000000 physmap-flash physmap-flash.0: map_probe failed libphy: Fixed MDIO Bus: probed libphy: CNS3xxx MII Bus: probed eth0: RGMII PHY 0 on cns3xxx Switch ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-platform: EHCI generic platform driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-pci: OHCI PCI platform driver ohci-platform: OHCI generic platform driver usbcore: registered new interface driver usb-storage mousedev: PS/2 mouse device common for all mice CNS3XXX Real Time Clock, (c) 2009 Cavium Networks rtc irq:23 rtc rtc0: invalid alarm value: 1900-1-21 0:0:0 cns3xxx-rtc cns3xxx-rtc: rtc core: registered cns3xxx-rtc as rtc0 i2c /dev entries driver adt7475 0-002e: ADT7473 device, revision 0 adt7475 0-002e: Optional features: fan4 pwm2 usbcore: registered new interface driver usbhid usbhid: USB HID core driver Initializing XFRM netlink socket NET: Registered protocol family 17 NET: Registered protocol family 15 bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. PCI-E0 uses external clock source. ata1: SATA link down (SStatus 0 SControl 300) PCIe: Port[0] Enable PCIe LTSSM PCIe: Port[0] Check data link layer... ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-8: HGST HTS725050A7E630, GH2ZB550, max UDMA/133 ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 scsi 1:0:0:0: Direct-Access ATA HGST HTS725050A7 B550 PQ: 0 ANSI: 5 sd 1:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) sd 1:0:0:0: [sda] 4096-byte physical blocks sd 1:0:0:0: [sda] Write Protect is off sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sd 1:0:0:0: [sda] Attached SCSI disk Device not found. EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) VFS: Mounted root (ext3 filesystem) on device 8:1. devtmpfs: mounted Freeing unused kernel memory: 212K systemd[1]: System time before build time, advancing clock. ip_tables: (C) 2000-2006 Netfilter Core Team random: systemd: uninitialized urandom read (16 bytes read, 29 bits of entropy available) systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 9 (stretch)! systemd[1]: Set hostname to <seagate-dev>. random: systemd: uninitialized urandom read (16 bytes read, 35 bits of entropy available) random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 37 bits of entropy available) random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 38 bits of entropy available) random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 38 bits of entropy available) random: systemd-cryptse: uninitialized urandom read (16 bytes read, 38 bits of entropy available) random: systemd: uninitialized urandom read (16 bytes read, 45 bits of entropy available) random: systemd: uninitialized urandom read (16 bytes read, 45 bits of entropy available) random: systemd: uninitialized urandom read (16 bytes read, 45 bits of entropy available) random: systemd: uninitialized urandom read (16 bytes read, 45 bits of entropy available) systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... systemd[1]: Mounting Debug File System... Mounting Debug File System... systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... systemd[1]: dev-hugepages.mount: Couldn't determine result for ConditionVirtualization=!private-users, assuming failed: No such file or directory systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. systemd[1]: Reached target Paths. [ OK ] Reached target Paths. systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. systemd[1]: Reached target Swap. [ OK ] Reached target Swap. systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). systemd[1]: Starting Journal Service... Starting Journal Service... systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. systemd[1]: Starting Create list of required static device nodes for the current kernel... Starting Create list of required st…ce nodes for the current kernel... systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. systemd[1]: Reached target Slices. [ OK ] Reached target Slices. systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File System. systemd[1]: Mounted Debug File System. [ OK ] Mounted Debug File System. systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Started Load Kernel Modules. Starting Apply Kernel Variables... Starting Create Static Device Nodes in /dev... Starting Load/Save Random Seed... Starting udev Coldplug all Devices... Starting Flush Journal to Persistent Storage... [ OK ] Started Apply Kernel Variables. [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Static Device Nodes in /dev. systemd-journald[481]: Received request to flush runtime journal from PID 1 Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Coldplug all Devices. [ OK ] Started udev Kernel Device Manager. Starting Create Volatile Files and Directories... [ OK ] Found device /dev/ttyS0. [ OK ] Started Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Network Time Synchronization. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Regular background program processing daemon. [ OK ] Started D-Bus System Message Bus. Starting Login Service... Starting System Logging Service... [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Reached target Timers. [ OK ] Started System Logging Service. [ OK ] Started Login Service. random: nonblocking pool is initialized
Hit any key to stop autoboot: 0 Serial Flash Sector 3 Erase OK! 0x00010000 mmc_init Detected SD Card 8133168 bytes read enter do_eth_down!!! ## Booting kernel from Legacy Image at 08000000 ... Image Name: Linux-2.6.35.13-cavm1.whitney-ec Created: 2015-03-10 2:09:28 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 8133104 Bytes = 7.8 MB Load Address: 02000000 Entry Point: 02000000 Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.35.13-cavm1.whitney-econa.whitney-econa (builder@ubuntu) (gcc version 4.4.1 (MontaVista Linux G++ 4.4-) ) #2 Mon Mar 9 19:09:21 PDT 2015 [ 0.000000] Whitney release v1.1-beta5 [ 0.000000] CPU: ARMv6-compatible processor [410fb024] revision 4 (ARMv7), cr=00c5387f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine: Cavium Networks CNS3420 Validation Board [ 0.000000] Ignoring unrecognised tag 0x00000000 [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8188 [ 0.000000] Kernel command line: console=ttyS0,38400 mem=512M root=/dev/md0 rootwait [ 0.000000] PID hash table entries: 2048 (order: -3, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 2, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 1, 131072 bytes) [ 0.000000] allocated 163840 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 510592k/510592k available, 13696k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0x00000000 ( 64 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xff600000 - 0xffe00000 ( 8 MB) [ 0.000000] vmalloc : 0xc0800000 - 0xe0000000 ( 504 MB) [ 0.000000] lowmem : 0xa0000000 - 0xc0000000 ( 512 MB) [ 0.000000] modules : 0x9f000000 - 0xa0000000 ( 16 MB) [ 0.000000] .init : 0xa0008000 - 0xa04f0000 (5024 kB) [ 0.000000] .text : 0xa04f0000 - 0xa0ab0000 (5888 kB) [ 0.000000] .data : 0xa0b12000 - 0xa0b5db80 ( 303 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU-based detection of stalled CPUs is disabled. [ 0.000000] Verbose stalled-CPUs detection is disabled. [ 0.000000] NR_IRQS:160 [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [ttyS0] enabled [ 0.020000] Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736) [ 0.260000] pid_max: default: 32768 minimum: 301 [ 0.270000] Mount-cache hash table entries: 8192 [ 0.280000] Initializing cgroup subsys ns [ 0.290000] Initializing cgroup subsys cpuacct [ 0.300000] Initializing cgroup subsys memory [ 0.310000] Initializing cgroup subsys devices [ 0.320000] Initializing cgroup subsys freezer [ 0.330000] Initializing cgroup subsys net_cls [ 0.340000] Initializing cgroup subsys blkio [ 0.350000] CPU: Testing write buffer coherency: [ 0.360000] ok [ 0.360000] CNS3XXX: no. of cores (2) greater than configured maximum of 1 - clipping [ 0.370000] CPU1: Booted secondary processor [ 0.370000] <0> DP-core moving to WFI [ 0.370000] cvm_nas_init: cvm_nas_task init [ 0.380000] cvm_nas_init: proc init success [ 0.400000] devtmpfs: initialized [ 0.410000] NET: Registered protocol family 16 [ 0.420000] L310 cache controller enabled [ 0.430000] l2x0: 8 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x02540000, Cache size: 262144 B [ 0.440000] cns_rdma_init: start [ 0.450000] cns_rdma_init: reg1: virt=0xbc015d48 [ 0.460000] cns_rdma_init: pre-allocating rdma_sg: 32*280=8960 [ 0.470000] cns_rdma_init: q1: virt=0xbc0b3a00, phy=0x3c0b3a00 -> 0x3c0b3bf0 [ 0.480000] cns_rdma_init: done, err=0 [ 0.490000] Cavium feature enabled: SOP-PURENAS, 64KB page size, Jumbo frame, [ 0.510000] bio: create slab <bio-0> at 0 [ 0.520000] vgaarb: loaded [ 0.530000] SCSI subsystem initialized [ 0.540000] usbcore: registered new interface driver usbfs [ 0.560000] usbcore: registered new interface driver hub [ 0.570000] usbcore: registered new device driver usb [ 0.750000] raid6: int32x1 91 MB/s [ 0.930000] raid6: int32x2 128 MB/s [ 1.110000] raid6: int32x4 126 MB/s [ 1.290000] raid6: int32x8 138 MB/s [ 1.470000] raid6: CNS-RAID 48 MB/s [ 1.480000] raid6: using algorithm CNS-RAID (48 MB/s) [ 1.490000] Switching to clocksource timer1 [ 1.500000] Slow work thread pool: Starting up [ 1.510000] Slow work thread pool: Ready [ 1.520000] FS-Cache: Loaded [ 1.550000] NET: Registered protocol family 2 [ 1.560000] IP route cache hash table entries: 16384 (order: 0, 65536 bytes) [ 1.570000] TCP established hash table entries: 16384 (order: 1, 131072 bytes) [ 1.580000] TCP bind hash table entries: 16384 (order: 0, 65536 bytes) [ 1.590000] TCP: Hash tables configured (established 16384 bind 16384) [ 1.600000] TCP reno registered [ 1.610000] UDP hash table entries: 4096 (order: 0, 65536 bytes) [ 1.620000] UDP-Lite hash table entries: 4096 (order: 0, 65536 bytes) [ 1.630000] NET: Registered protocol family 1 [ 1.640000] RPC: Registered udp transport module. [ 1.650000] RPC: Registered tcp transport module. [ 1.660000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.640000] CNS3XXX PCIe Host Control Driver [ 2.650000] =============================== [ 2.660000] CNS3XXX PCIe support both internal and external clock. [ 2.670000] However, incorrect selection may result in system hang. [ 2.680000] If booting hangs, please select choose [ 2.690000] CONFIG_CNS3XXX_INTERNAL_CLOCK_SOURCE [ 2.700000] instead. [ 2.700000] =============================== [ 2.710000] PCI-E0 uses external clock source. [ 2.720000] PCIe: Port[0] Enable PCIe LTSSM [ 2.730000] PCIe: Port[0] Check data link layer... [ 3.250000] Device not found. [ 3.250000] PCIe: Set Bridge Max_Payload_Size to 128 byte [ 3.260000] PCIe: Set Bridge Max_Read_Request_Size to 128 byte [ 3.270000] PCI: bus0: Fast back to back transfers disabled [ 3.280000] PCI: bus1: Fast back to back transfers enabled [ 3.290000] PCIe0: Bridge found. [ 3.300000] PCI: enabling device 0000:00:00.0 (0140 -> 0143) [ 3.310000] PCIe0 map irq: 0000:00:00.00 slot 0, pin 1, irq: 87 [ 3.320000] VFS: Disk quotas dquot_6.5.2 [ 3.330000] Dquot-cache hash table entries: 16384 (order 0, 65536 bytes) [ 3.340000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 3.350000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 3.360000] NTFS driver 2.1.29 [Flags: R/W]. [ 3.370000] fuse init (API version 7.14) [ 3.380000] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 3.390000] SGI XFS Quota Management subsystem [ 3.400000] GFS2 (built Mar 9 2015 19:07:00) installed [ 3.410000] msgmni has been set to 996 [ 3.420000] alg: No test for stdrng (krng) [ 3.430000] io scheduler noop registered [ 3.440000] io scheduler deadline registered (default) [ 3.460000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 3.470000] serial8250: ttyS0 at MMIO 0x78000000 (irq = 45) is a 16550A [ 3.480000] brd: module loaded [ 3.490000] loop: module loaded [ 3.500000] drbd: initialized. Version: 8.3.8 (api:88/proto:86-94) [ 3.510000] drbd: built-in [ 3.520000] drbd: registered as block device major 147 [ 3.530000] drbd: minor_table @ 0xbc0387e0 [ 3.540000] Loading iSCSI transport class v2.0-870. [ 3.550000] iscsi: registered transport (tcp) [ 3.560000] cns3xxx_spi_probe: setup CNS3XXX SPI Controller in polling mode, w/o DMA [ 3.580000] SPI bit rate = 116/64 Mhz [ 3.590000] m25p80 spi1.0: found mx25l4005a, expected m25p80 [ 3.600000] m25p80 spi1.0: mx25l4005a (512 Kbytes) [ 3.610000] Creating 3 MTD partitions on "spi1.0": [ 3.620000] 0x000000000000-0x000000030000 : "SPI-UBoot" [ 3.640000] 0x000000030000-0x000000040000 : "SPI-UBootEnv" [ 3.650000] 0x000000040000-0x000000080000 : "SPI-FileSystem" [ 3.660000] CNS3XXX AHCI SATA low-level driver [ 3.670000] SATA Port0 Spread-spectrum : Disable [ 3.680000] SATA Port0 Spread-spectrum : Enable [ 3.690000] SATA Port1 Spread-spectrum : Disable [ 3.700000] SATA Port1 Spread-spectrum : Enable [ 3.710000] cns3xxx-ahci cns3xxx-ahci.0: forcing PORTS_IMPL to 0x3 [ 3.720000] CPU clock : 700 [ 3.730000] *** Timer 1ms: 100000(0x186a0) *** [ 3.740000] *** Set to: 350000(0x55730) *** [ 3.750000] cns3xxx-ahci cns3xxx-ahci.0: AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl SATA mode [ 3.760000] cns3xxx-ahci cns3xxx-ahci.0: flags: ncq sntf pm led clo only pmp pio slum part [ 3.770000] scsi0 : cns3xxx-ahci [ 3.780000] scsi1 : cns3xxx-ahci [ 3.790000] ata1: SATA max UDMA/133 ahci bar m16777216@0x83000000 port 0x83000100 irq 65 [ 3.800000] ata2: SATA max UDMA/133 ahci bar m16777216@0x83000000 port 0x83000180 irq 65 [ 3.820000] tun: Universal TUN/TAP device driver, 1.6 [ 3.830000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 3.840000] mice: PS/2 mouse device common for all mice [ 3.850000] CNS3XXX Real Time Clock, (c) 2009 Cavium Networks [ 3.860000] rtc irq:23 [ 3.860000] cns3xxx-rtc cns3xxx-rtc: rtc core: registered cns3xxx-rtc as rtc0 [ 4.380000] i2c /dev entries driver [ 4.400000] adt7475 0-002e: ADT7473 device, revision 0 [ 4.410000] adt7475 0-002e: Optional features: fan4 pwm2 [ 4.420000] CNS3XXX Watchdog Timer, noboot=0 margin=60 sec (nowayout= 0) [ 4.430000] watchdog: cns3xxx_wdt_probe [ 4.440000] watchdog irq = 30 [ 4.450000] watchdog start_regs = 0xC0A00600 [ 4.520000] Watchdog timer frequency : 349.98MHz. [ 4.530000] ata1: SATA link down (SStatus 0 SControl 300) [ 4.540000] md: linear personality registered for level -1 [ 4.550000] md: raid0 personality registered for level 0 [ 4.560000] md: raid1 personality registered for level 1 [ 4.570000] xor: measuring software checksum speed [ 4.630000] arm4regs : 448.000 MB/sec [ 4.690000] 8regs : 275.200 MB/sec [ 4.750000] 32regs : 300.800 MB/sec [ 4.810000] CNS-RAID : 454.400 MB/sec [ 4.820000] xor: using function: CNS-RAID (454.400 MB/sec) [ 4.830000] md: raid6 personality registered for level 6 [ 4.840000] md: raid5 personality registered for level 5 [ 4.850000] md: raid4 personality registered for level 4 [ 4.860000] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com [ 4.870000] sdhci: Secure Digital Host Controller Interface driver [ 4.880000] sdhci: Copyright(c) Pierre Ossman [ 4.890000] sdhci-cns3xxx, (c) 2009 Cavium Networks [ 4.910000] mmc0: SDHCI controller on cns3xxx [sdhci-cns3xxx.0] using PIO [ 4.920000] usbcore: registered new interface driver hiddev [ 4.940000] usbcore: registered new interface driver usbhid [ 4.950000] usbhid: USB HID core driver [ 4.960000] TCP cubic registered [ 4.970000] NET: Registered protocol family 17 [ 4.980000] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 4 [ 5.000000] cns3xxx-rtc cns3xxx-rtc: setting system clock to 2018-03-20 21:51:38 UTC (1521582698) [ 5.040000] mmc0: new high speed SD card at address 0007 [ 5.050000] mmcblk0: mmc0:0007 SD256 246 MiB [ 5.060000] mmcblk0: p1 p2 p3 p4 [ 11.930000] ata2: link is slow to respond, please be patient (ready=0) [ 23.880000] ata2: softreset failed (device not ready) [ 24.070000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 24.090000] ata2.00: ATA-8: HGST HTS725050A7E630, GH2ZB550, max UDMA/133 [ 24.100000] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 24.110000] ata2.00: configured for UDMA/133 [ 24.140000] scsi 1:0:0:0: Direct-Access ATA HGST HTS725050A7 GH2Z PQ: 0 ANSI: 5 [ 24.150000] sd 1:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) [ 24.160000] sd 1:0:0:0: [sda] 4096-byte physical blocks [ 24.170000] sd 1:0:0:0: [sda] Write Protect is off [ 24.180000] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 24.190000] sda: sda1 [ 24.560000] sd 1:0:0:0: [sda] Attached SCSI disk Starting initramfs boot... rootdelay parameter was not passed on kernel command line - assuming 2s delay If you would like to avoid this delay, pass explicit rootdelay=0 Waiting 2 seconds for devices to settle... initramfs: Creating device nodes: sda sda1 initramfs: Loading /initrd.d/60-sop.sh module [ 26.770000] GPIOB_PIN_EN_REG: c430ff80 [ 26.780000] [ 26.780000] Do power enable [ 26.790000] Disabling MAC Ports [ 26.800000] Suspending DMA [ 26.810000] Waiting for DMA Status not IDLE [ 26.820000] 0 0 [ 26.820000] done [ 26.830000] Do power reset [ 26.840000] do cns3xxx gsw memory test [ 26.850000] cns3xxx gsw memory test is complete [ 26.860000] CNS3XXX PSE: Initialize init_port: 7 [ 26.880000] MAC 0 [ 26.880000] phy_id: 1c [ 26.890000] Initialize RTL8211 [ 26.900000] do_ssc_test[64]: phy_addr = 00000001 [ 26.920000] MAC 1 [ 26.920000] phy_id: 1c [ 26.930000] Initialize RTL8211 [ 26.940000] do_ssc_test[64]: phy_addr = 00000002 [ 26.960000] MAC 2 [ 26.960000] vid: 1 [ 26.960000] pmap: 0x4 [ 26.960000] age_field: 7 [ 26.960000] vlan_mac: 1 [ 26.960000] filter: 0 [ 26.960000] mac addr: 0:10:75:38:d0:cc [ 26.970000] cns3xxx_probe: using uboot env MAC addr: 00:10:75:38:d0:cc [ 26.980000] vid: 2 [ 26.980000] pmap: 0x4 [ 26.980000] age_field: 7 [ 26.980000] vlan_mac: 1 [ 26.980000] filter: 0 [ 26.980000] mac addr: 0:10:75:38:d0:cd [ 26.990000] cns3xxx_probe: using uboot env MAC addr: 00:10:75:38:d0:cd [ 27.000000] pse register_pm_notifer 0 [ 27.010000] CPU0: Initializing DataPlane... [ 27.020000] dataPlaneInit: Initializing the rings [ 27.030000] dataPlaneInit: Page Ring Fill for the first time [ 27.040000] ... cns3xxx_setup_all_tx_resources [ 27.050000] ... cns3xxx_setup_all_rx_resources ## ring_num : 0 [ 27.060000] CPC: rx resources setup done [ 27.070000] dataPlaneInit: Page Ring Fill for the second time [ 27.080000] CP[ 27.o80000] mCPng out oore com<6>[ 27.080000] ing out of WFI [ 27.080000] CPU1: dataPlaneEntry .... [ 27.080000] Start Address of seg_hdr = a0bb7e60, End addr = a0bd7e5f initramfs: Loading /initrd.d/80-md.sh module No bootable drives initramfs: Loading /initrd.d/85-nfsboot.sh module INIT: version 2.86 booting Please wait: booting... Traceback (most recent call last): File "/usr/lib/python2.6/site-packages/shares/server.py", line 86, in <module> server = Server(socketname, ServerHandler) File "/usr/lib/python2.6/SocketServer.py", line 400, in __init__ self.server_bind() File "/usr/lib/python2.6/SocketServer.py", line 411, in server_bind self.socket.bind(self.server_address) File "<string>", line 1, in bind socket.error: [Errno 30] Read-only file system rm: cannot remove /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system chown: changing ownership of /var/spool/cups/tmp: Read-only file system chown: changing ownership of /var/spool/cups: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system chmod: changing permissions of /var/spool/cups/tmp: Read-only file system chmod: changing permissions of /var/spool/cups: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system /etc/init.d/rcS: /etc/rcS.d/S02populate-volatile.sh: line 1: can't create /etc/volatile.cache: Read-only file system mount: sysfs already mounted or /sys busy mount: according to mtab, sysfs is already mounted on /sys Starting udev touch: cannot touch /tmp/stype: Read-only file system Remounting root file system... mdadm: /dev/md2 not identified in config file. mount: special device /dev/md2 does not exist umount: /dev/md2: not found mdadm: error opening /dev/md2: No such file or directory umount: /media/cf: device is busy. (In some cases useful info about processes that use the device is found by lsof(8) or fuser(1)) Starting up raid using + d1=sda + d2=sdb + d3=sdc + d4=sdd + devcnt=0 + params=<drives name="set"> + eval dir=/sys/block/$d1 + dir=/sys/block/sda + [ ! -d /sys/block/sda ] + eval device=/dev/$d1 + device=/dev/sda + parted /dev/sda --script print + sed 1,/Number/ d + wc -l + part_cnt=2 + [ 2 -ge 1 ] + continue + eval dir=/sys/block/$d2 + dir=/sys/block/sdb + [ ! -d /sys/block/sdb ] + continue + eval dir=/sys/block/$d3 + dir=/sys/block/sdc + [ ! -d /sys/block/sdc ] + continue + eval dir=/sys/block/$d4 + dir=/sys/block/sdd + [ ! -d /sys/block/sdd ] + continue + params=<drives name="set"></drives> + [ 0 -ge 1 ] + test true = true + cat /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid6] [raid5] [raid4] unused devices: <none> + sh /usr/sbin/sys_part_recover + exit 0 mkdir: cannot create directory /VolumeData: Read-only file system Setting up IP spoofing protection: rp_filter. Configuring network interfaces... /usr/bin/restart_mini_dlna: cd: line 12: can't cd to /usr/config/backupconfig / run-parts: /etc/network/if-up.d/20-upnp exited with code 1 done. Failed to kill daemon. (No such file or directory) [ 40.200000] dev->name: eth0 ## dev->features: 1116179 Failed to kill daemon. (No such file or directory) [ 40.370000] dev->name: eth1 ## dev->features: 1116179 Starting portmap daemon: portmap. rm: cannot remove directory /tmp: Read-only file system ln: creating symbolic link /tmp/tmp: Read-only file system Collected errors: * opkg_conf_init: Creating temp dir /tmp/opkg-qgEbzs failed: Read-only file system rm: cannot remove /etc/rcS.d/S98configure: Read-only file system Letting uboot know initramfs kernel was successful [ 45.680000] EXT4-fs (mmcblk0p4): warning: maximal mount count reached, running e2fsck is recommended [ 45.740000] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null) INIT: Entering runlevel: 5 Starting system message bus: dbus. /etc/rc5.d/S20mountcomplete: line 5: can't create /etc/.usb_lck: Read-only file system Starting S.M.A.R.T. daemon: smartd. * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [ ok ] Starting Lighttpd Web Server: lighttpd. /usr/bin/setup-lcd: line 8: can't create /proc/cns3xxx/st7066: nonexistent directory /usr/bin/setup-lcd: line 9: can't create /proc/cns3xxx/st7066: nonexistent directory /etc/rc5.d/S99sysready.sh: line 11: can't create /etc/dflags/sdflag: Read-only file system rm: cannot remove /tmp/.volume_migrate: Read-only file system MontaVista(R) Linux(R) 6.0 MontaVista Linux 6 .dev-snapshot-20150310 whitney-econa-2bay console whitney-econa-2bay login: /usr/bin/setup-lcd: line 75: can't create /proc/cns3xxx/st7066: nonexistent directory /usr/bin/setup-lcd: line 75: can't create /proc/cns3xxx/st7066: nonexistent directory /usr/bin/setup-lcd: line 75: can't create /proc/cns3xxx/st7066: nonexistent directory /usr/bin/setup-lcd: line 75: can't create /proc/cns3xxx/st7066: nonexistent directory /usr/bin/setup-lcd: line 75: can't create /proc/cns3xxx/st7066: nonexistent directory /usr/bin/setup-lcd: line 75: can't create /proc/cns3xxx/st7066: nonexistent directory /usr/bin/setup-lcd: line 75: can't create /proc/cns3xxx/st7066: nonexistent directory /usr/bin/setup-lcd: line 75: can't create /proc/cns3xxx/st7066: nonexistent directory MontaVista(R) Linux(R) 6.0 MontaVista Linux 6 .dev-snapshot-20150310 whitney-econa-2bay console whitney-econa-2bay login:
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package March 20, 2018 05:37PM |
Registered: 6 years ago Posts: 18 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package March 20, 2018 05:40PM |
Registered: 6 years ago Posts: 42 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package March 20, 2018 06:05PM |
Registered: 6 years ago Posts: 18 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package March 20, 2018 06:38PM |
Registered: 6 years ago Posts: 42 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package March 21, 2018 10:03AM |
Registered: 6 years ago Posts: 42 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package March 22, 2018 02:31PM |
Registered: 6 years ago Posts: 18 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package March 22, 2018 02:56PM |
Registered: 6 years ago Posts: 42 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package April 08, 2018 11:03AM |
Registered: 6 years ago Posts: 42 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package April 09, 2018 02:13AM |
Admin Registered: 13 years ago Posts: 19,007 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package April 09, 2018 05:58AM |
Registered: 6 years ago Posts: 42 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package April 10, 2018 01:56PM |
Registered: 10 years ago Posts: 46 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package April 10, 2018 06:05PM |
Admin Registered: 13 years ago Posts: 19,007 |
Quote
These OXNAS boxes uses the ARM11 MPCore, which has some internal CPU bugs, and has proven to be problematic any time there is significant upstream modification in SMP related code. Thus, I've chosen to stay tracked with an LTS kernel to ensure there is enough upstream tests before moving on to the next version. And therefore I will release a minor version in the series 4.4.x whenever there will be kernel security fixes. After this 4.4 LTS version will have been expired, I will move to a new LTS kernel so we can get the latest Linux features.
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package April 15, 2018 03:19PM |
Registered: 6 years ago Posts: 18 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package April 15, 2018 09:06PM |
Registered: 6 years ago Posts: 42 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package April 16, 2018 07:58AM |
Registered: 6 years ago Posts: 42 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package April 16, 2018 12:34PM |
Registered: 10 years ago Posts: 46 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package April 16, 2018 12:43PM |
Registered: 6 years ago Posts: 42 |
[ 3.290000] Board version 1.x. [ 3.290000] PCI-E0 uses external clock source. [ 3.300000] Active PCIe0 Clock, PHY and reset PCIe [ 3.300000] PCIe: Port[0] Enable PCIe LTSSM [ 3.310000] PCIe: Port[0] Check data link layer... [ 3.320000] Link up. [ 3.320000] PCI host bridge to bus 0000:00 [ 3.330000] pci_bus 0000:00: root bus resource [io 0xac000000-0xacffffff] [ 3.340000] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xaaffffff] [ 3.360000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 3.380000] pci 0000:00:00.0: [177d:3400] type 01 class 0x060400 [ 3.380000] pci 0000:00:00.0: supports D1 D2 [ 3.380000] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.380000] PCI: bus0: Fast back to back transfers disabled
grep -i pci .config |grep -v ^# CONFIG_MIGHT_HAVE_PCI=y CONFIG_PCI_QUIRKS=y CONFIG_PCI=y CONFIG_PCI_DOMAINS=y CONFIG_PCI_DOMAINS_GENERIC=y CONFIG_PCI_SYSCALL=y CONFIG_OF_ADDRESS_PCI=y CONFIG_OF_PCI=y CONFIG_OF_PCI_IRQ=y CONFIG_SERIAL_8250_PCI=y CONFIG_USB_XHCI_PCI=y CONFIG_USB_EHCI_PCI=y CONFIG_USB_OHCI_HCD_PCI=y CONFIG_MMC_SDHCI_PCI=m CONFIG_GENERIC_PCI_IOMAP=y
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package April 16, 2018 12:45PM |
Registered: 10 years ago Posts: 46 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package April 16, 2018 03:28PM |
Registered: 6 years ago Posts: 18 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package April 16, 2018 04:32PM |
Registered: 10 years ago Posts: 46 |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package April 29, 2018 05:56PM |
Registered: 6 years ago Posts: 1 |
AndyP
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package May 05, 2018 04:34PM |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package May 05, 2018 08:13PM |
Registered: 6 years ago Posts: 42 |
AndyP
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package May 06, 2018 12:03PM |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package May 06, 2018 12:36PM |
Registered: 6 years ago Posts: 42 |
dhcp setenv serverip 192.168.1.1; setenv bootargs 'console=ttyS0,38400 mem=512M@0x20000000 root=/dev/sda3 rootwait'; tftp 0x28000000 uImage; bootm 0x28000000
KeithMnemonic
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package June 17, 2019 03:22PM |
Re: (WIP) Linux Kernel and rootfs 4.14.24 for Seagate Business Storage NAS (CNS3xxx) package November 06, 2019 11:36PM |
Admin Registered: 13 years ago Posts: 19,007 |