Debian on HP T5325 Thin Client
Posted by Gravelrash
|
Debian on HP T5325 Thin Client January 27, 2016 12:34PM |
Registered: 9 years ago Posts: 1,037 |
@bodhi
Below are the attached and unfiltered outputs as taken straight from the unit - I was lucky in that the default password for the root account hadnt been changed (pheew)
Attached are the outputs from the following : fstab : fw_printenv : fdisk -l : dmesg
I havent got as far as attempting to do a kwboot with the device as I am going to have to get my soldering iron in there, the connector for the serial console is absolutely tiny, so small that it makes the one on the Pogoplug pink look like giant
I hope you can help with this one
EDIT 2 : link to original discussion to create consistency for anyone following
http://forum.doozan.com/read.php?8,25389
-------
bodhi edit: changed thread title to make it easier to find.
============================
Breaking stuff since 1994 :-)
============================
Edited 5 time(s). Last edit at 09/12/2017 06:59PM by bodhi.
Below are the attached and unfiltered outputs as taken straight from the unit - I was lucky in that the default password for the root account hadnt been changed (pheew)
Attached are the outputs from the following : fstab : fw_printenv : fdisk -l : dmesg
I havent got as far as attempting to do a kwboot with the device as I am going to have to get my soldering iron in there, the connector for the serial console is absolutely tiny, so small that it makes the one on the Pogoplug pink look like giant
I hope you can help with this one
EDIT 2 : link to original discussion to create consistency for anyone following
http://forum.doozan.com/read.php?8,25389
-------
bodhi edit: changed thread title to make it easier to find.
============================
Breaking stuff since 1994 :-)
============================
Edited 5 time(s). Last edit at 09/12/2017 06:59PM by bodhi.
|
Re: HP T5325 Thin Client Debian January 27, 2016 04:34PM |
Registered: 9 years ago Posts: 442 |
|
Re: HP T5325 Thin Client Debian January 27, 2016 05:37PM |
Registered: 9 years ago Posts: 1,037 |
|
Re: HP T5325 Thin Client Debian January 27, 2016 09:34PM |
Admin Registered: 13 years ago Posts: 18,543 |
Gravelrash,
Looks good so far! Please post these in code tags (attached files are hard to read):
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 3 time(s). Last edit at 01/28/2016 04:03AM by bodhi.
Looks good so far! Please post these in code tags (attached files are hard to read):
cat /etc/fw_env.config fw_printenv which fw_setenv dpkg -l | grep -i mtd cat /proc/mtd ls -l /dev/mtd*
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 3 time(s). Last edit at 01/28/2016 04:03AM by bodhi.
|
Re: HP T5325 Thin Client Debian January 28, 2016 04:01AM |
Admin Registered: 13 years ago Posts: 18,543 |
With serial console, booting the latest Debian rootfs will be much easier and safer. Everything I've seen telling me that we'll able to do that.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: HP T5325 Thin Client Debian January 28, 2016 06:27AM |
Registered: 9 years ago Posts: 1,037 |
cat /etc/fw_env.config
fw_printenv
which fw_setenv
dpkg -l | grep -i mtd
cat /proc/mtd
ls -l /dev/mtd*
fdisk and fstab
DMESG
root@HPf4ce462327d3:/# cat /etc/fw_env.config cat: /etc/fw_env.config: No such file or directory
fw_printenv
root@HPf4ce462327d3:/# fw_printenv baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ run_diag=no console=console=ttyS0,115200 mtdparts=spi_flash:0x80000@0(uboot)ro,0x80000@0x80000(root) CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage usb_bootargs=root=/dev/ram rw bootusb=usb start;fatload usb 0 0x800000 /boot/uImage.usb;fatload usb 0 0x1100000 /boot/uInitrd.usb usbboot=setenv bootargs $(usb_bootargs); run bootusb; bootm 0x800000 0x1100000 thinpro_bootargs=root=/dev/sda1 rw init=/init video=xgifb splash quiet thinpro=ide reset; ext2load ide 0:1 0x200000 /boot/uImage; wol; setenv bootargs $(thinpro_bootargs); bootm 0x200000 pcieTune=yes mfgmode=setenv bootdelay 3; setenv in_mfg yes;setenvh GotoWOL Yes; setenvh WOLEnabled No; setenv bootcmd run mfgboot; saveenv; reset mfgbootargs=setenv bootargs root=/dev/sdb1 rw init=/init ip=dhcp rootdelay=8 $(console) udevtimeout=8 mfgboot=usb start; ext2load usb 0:1 0x2000000 /boot/uImage; run mfgbootargs; bootm 0x2000000 product=setenv bootdelay 1; setenv in_mfg no;setenvh GotoWOL No; setenvh WOLEnabled Yes; setenv bootcmd run thinpro; saveenv; reset standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 ethaddr=f4:ce:46:23:27:d3 gatewayip=10.4.50.5 netmask=255.255.255.0 ipaddr=10.4.50.151 serverip=10.4.50.5 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no disaMvPnp=no enaAutoRecovery=yes bootdelay=1 in_mfg=no bootcmd=run thinpro root@HPf4ce462327d3:/#
which fw_setenv
root@HPf4ce462327d3:/# which fw_setenv /usr/sbin/fw_setenv
dpkg -l | grep -i mtd
root@HPf4ce462327d3:/# dpkg -l | grep -i mtd root@HPf4ce462327d3:/#
cat /proc/mtd
root@HPf4ce462327d3:/# cat /proc/mtd dev: size erasesize name mtd0: 00010000 00010000 "u-boot env" mtd1: 00010000 00010000 "permanent u-boot env" mtd2: 00010000 00010000 "HP env" mtd3: 00080000 00010000 "u-boot" mtd4: 00040000 00010000 "SSD firmware"
ls -l /dev/mtd*
root@HPf4ce462327d3:/# ls -l /dev/mtd* crw-rw---- 1 root root 90, 0 Jan 28 12:11 /dev/mtd0 crw-rw---- 1 root root 90, 1 Jan 28 12:11 /dev/mtd0ro crw-rw---- 1 root root 90, 2 Jan 28 12:11 /dev/mtd1 crw-rw---- 1 root root 90, 3 Jan 28 12:11 /dev/mtd1ro crw-rw---- 1 root root 90, 4 Jan 28 12:11 /dev/mtd2 crw-rw---- 1 root root 90, 5 Jan 28 12:11 /dev/mtd2ro crw-rw---- 1 root root 90, 6 Jan 28 12:11 /dev/mtd3 crw-rw---- 1 root root 90, 7 Jan 28 12:11 /dev/mtd3ro crw-rw---- 1 root root 90, 8 Jan 28 12:11 /dev/mtd4 crw-rw---- 1 root root 90, 9 Jan 28 12:11 /dev/mtd4ro brw-rw---- 1 root disk 31, 0 Jan 28 12:11 /dev/mtdblock0 brw-rw---- 1 root disk 31, 1 Jan 28 12:11 /dev/mtdblock1 brw-rw---- 1 root disk 31, 2 Jan 28 12:11 /dev/mtdblock2 brw-rw---- 1 root disk 31, 3 Jan 28 12:11 /dev/mtdblock3 brw-rw---- 1 root disk 31, 4 Jan 28 12:11 /dev/mtdblock4
fdisk and fstab
:: FDISK :: Disk /dev/sda: 486 MB, 486162432 bytes 16 heads, 63 sectors/track, 942 cylinders Units = cylinders of 1008 * 512 = 516096 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 * 1 942 474736+ 83 Linux ---------------------------------------------------------------- :: /etc/fstab :: LABEL=ROOT /.flash ext3 noauto,rw 0 0 /dev/loop0 /.flash/origfs squashfs noauto,ro 0 0 aufs / aufs noauto,ro,noplink,br:/.flash/root-cow=rw:/.flash/origfs=rr 0 0 aufs /writable aufs noauto,rw,noplink,br:/.flash/writable-cow=rw:/.flash/origfs/writable=rr 0 0 proc /proc proc defaults 0 0 none /tmp tmpfs rw 0 0 ----------------------------------------------------------------
DMESG
[ 0.000000] Linux version 2.6.22.18-2-armel (root@lenny-devel) (gcc version 4.2.1) #1 PREEMPT Tue Nov 17 13:34:38 EST 2009 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] DMA zone: 1024 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 130048 pages, LIFO batch:31 [ 0.000000] Normal zone: 0 pages used for memmap [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 130048 [ 0.000000] Kernel command line: root=/dev/sda1 rw init=/init video=xgifb splash quiet [ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.020000] Memory: 256MB 256MB 0MB 0MB = 512MB total [ 0.020000] Memory: 515584KB available (3508K code, 463K data, 108K init) [ 0.020000] Calibrating delay loop... 1199.30 BogoMIPS (lpj=5996544) [ 0.250000] Security Framework v1.0.0 initialized [ 0.250000] SELinux: Disabled at boot. [ 0.250000] Capability LSM initialized [ 0.250000] Mount-cache hash table entries: 512 [ 0.250000] CPU: Testing write buffer coherency: ok [ 0.250000] NET: Registered protocol family 16 [ 0.250000] [ 0.250000] CPU Interface [ 0.250000] ------------- [ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB [ 0.250000] SDRAM_CS1 ....base 10000000, size 256MB [ 0.250000] SDRAM_CS2 ....disable [ 0.250000] SDRAM_CS3 ....disable [ 0.250000] PEX0_MEM ....base e8000000, size 128MB [ 0.250000] PEX0_IO ....base f2000000, size 1MB [ 0.250000] INTER_REGS ....base f1000000, size 1MB [ 0.250000] NFLASH_CS ....base fa000000, size 2MB [ 0.250000] SPI_CS ....base f4000000, size 16MB [ 0.250000] BOOT_ROM_CS ....no such [ 0.250000] DEV_BOOTCS ....no such [ 0.250000] CRYPT_ENG ....base f0000000, size 2MB [ 0.250000] [ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- OpenRD-Base Soc: 88F6281 A0 LE [ 0.250000] [ 0.250000] Detected Tclk 200000000 and SysClk 400000000 [ 0.250000] MV Buttons Device Load [ 0.250000] rt5623 Codec device register [ 0.250000] Marvell USB EHCI Host controller #0: c0893200 [ 0.750000] PEX0 interface detected Link X1 [ 0.750000] PCI: bus0: Fast back to back transfers disabled [ 0.750000] SCSI subsystem initialized [ 0.760000] usbcore: registered new interface driver usbfs [ 0.760000] usbcore: registered new interface driver hub [ 0.760000] usbcore: registered new device driver usb [ 0.760000] NET: Registered protocol family 2 [ 0.770000] Time: kw_clocksource clocksource has been installed. [ 0.770000] Switched to high resolution mode on CPU 0 [ 0.850000] IP route cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.850000] TCP established hash table entries: 65536 (order: 7, 524288 bytes) [ 0.850000] TCP bind hash table entries: 65536 (order: 6, 262144 bytes) [ 0.850000] TCP: Hash tables configured (established 65536 bind 65536) [ 0.850000] TCP reno registered [ 0.880000] RTC registered [ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.880000] o RAID 5 Xor calculation [ 0.880000] o kernel memcpy [ 0.880000] o kenrel memzero [ 0.880000] Number of XOR engines to use: 4 [ 0.880000] CESA test started: bufNum = 1, bufSize = 20000 [ 0.880000] Cesa Test Start: pMbufSrc=c092f000, pFragsSrc=c08ae000, pMbufDst=c0929000, pFragsDst=c08f0000 [ 0.900000] mvCesaInit: sessions=32, queue=252, pSram=f0000000 [ 0.920000] cesadev_init(c0010edc) [ 0.920000] Warning: TS unit is powered off. [ 0.920000] MV Buttons Driver Load [ 0.920000] audit: initializing netlink socket (disabled) [ 0.920000] audit(1453933386.889:1): initialized [ 0.920000] VFS: Disk quotas dquot_6.5.1 [ 0.920000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.920000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.920000] squashfs: LZMA suppport for slax.org by jro [ 0.920000] aufs 20090126 [ 0.920000] io scheduler noop registered [ 0.920000] io scheduler cfq registered (default) [ 0.920000] XGIfb: Options <NULL> [ 0.920000] XGIfb: Relocate IO address: 1000 [00001030] [ 0.920000] XGIfb: Enable PCI device [ 0.920000] XGIfb: SR14=41 DramSzie 1000000 ChannelNum 1 [ 0.920000] XGIfb: Framebuffer at 0xe8000000, mapped to 0xe1000000, size 16384k [ 0.920000] XGIfb: MMIO at 0xec000000, mapped to 0xe0880000, size 256k [ 0.920000] XGIfb: XGIInitNew() ...OK [ 0.920000] XGIfb: Memory heap starting at 8192K [ 0.920000] XGIfb: Default mode is 1024x768x16 (60Hz) [ 0.920000] XGIfb: Change mode to 1024x768x16-60Hz [ 0.970000] Console: switching to colour frame buffer device 128x48 [ 1.020000] XGIfb: Installed XGIFB_GET_INFO ioctl (80046ef8) [ 1.020000] fb0: frame buffer device, Version 0.8.01 [ 1.040000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 1.040000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 1.040000] serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A [ 1.040000] RAMDISK driver initialized: 16 RAM disks of 8192K size 4096 blocksize [ 1.040000] loop: module loaded [ 1.040000] Loading Marvell Ethernet Driver: [ 1.040000] o Cached descriptors in DRAM [ 1.040000] o DRAM SW cache-coherency [ 1.040000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 1.040000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 1.040000] o TCP segmentation offload enabled [ 1.040000] o Receive checksum offload enabled [ 1.040000] o Transmit checksum offload enabled [ 1.040000] o Network Fast Processing (Routing) supported [ 1.040000] o Driver ERROR statistics enabled [ 1.040000] o Driver INFO statistics enabled [ 1.040000] o Proc tool API enabled [ 1.040000] o Rx descripors: q0=128 [ 1.040000] o Tx descripors: q0=532 [ 1.040000] o Loading network interface(s): [ 1.050000] o register under eth%d platform [ 1.050000] o eth0, ifindex = 1, GbE port = 0 [ 1.050000] o eth1, ifindex = 2, GbE port = 1 [ 1.050000] [ 1.050000] mvFpRuleDb (de710000): 16384 entries, 65536 bytes [ 1.050000] Integrated Sata device found [ 1.070000] scsi0 : Marvell SCSI to SATA adapter [ 1.070000] scsi1 : Marvell SCSI to SATA adapter [ 1.070000] SPI Serial flash detected @ 0xf4000000, 1024KB (16sec x 64KB) [ 1.070000] Creating 5 MTD partitions on "spi_flash": [ 1.070000] 0x000c0000-0x000d0000 : "u-boot env" [ 1.070000] 0x000d0000-0x000e0000 : "permanent u-boot env" [ 1.070000] 0x000e0000-0x000f0000 : "HP env" [ 1.070000] 0x00000000-0x00080000 : "u-boot" [ 1.080000] 0x00080000-0x000c0000 : "SSD firmware" [ 1.080000] usbmon: debugfs is not available [ 1.080000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.080000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.110000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.130000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.130000] usb usb1: configuration #1 chosen from 1 choice [ 1.130000] hub 1-0:1.0: USB hub found [ 1.130000] hub 1-0:1.0: 1 port detected [ 1.240000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.240000] mice: PS/2 mouse device common for all mice [ 1.240000] i2c /dev entries driver [ 1.240000] Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC). [ 1.240000] ASoC version 0.13.1 [ 1.240000] rt5623: RT5623 Audio Codec 0.01 [ 1.240000] asoc: RT5623 <-> mv88fx_-i2s mapping ok [ 1.250000] rt5623_codec_probe OK [ 1.250000] ALSA device list: [ 1.250000] #0: Dove (RT5623) [ 1.250000] Mirror/redirect action on [ 1.250000] TCP cubic registered [ 1.250000] NET: Registered protocol family 17 [ 1.250000] scsi: waiting for bus probes to complete ... [ 1.520000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.610000] scsi 0:0:0:0: Direct-Access ATA SM224 I052 PQ: 0 ANSI: 5 [ 1.610000] sd 0:0:0:0: [sda] 949536 512-byte hardware sectors (486 MB) [ 1.610000] sd 0:0:0:0: [sda] Write Protect is off [ 1.610000] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00 [ 1.610000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.610000] sd 0:0:0:0: [sda] 949536 512-byte hardware sectors (486 MB) [ 1.610000] sd 0:0:0:0: [sda] Write Protect is off [ 1.610000] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00 [ 1.610000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.610000] sda: sda1 [ 1.610000] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.610000] kjournald starting. Commit interval 5 seconds [ 1.620000] EXT3 FS on sda1, internal journal [ 1.620000] EXT3-fs: mounted filesystem with ordered data mode. [ 1.620000] VFS: Mounted root (ext3 filesystem). [ 1.620000] Freeing init memory: 108K [ 1.620000] Warning: unable to open an initial console. [ 1.700000] usb 1-1: configuration #1 chosen from 1 choice [ 1.710000] hub 1-1:1.0: USB hub found [ 1.710000] hub 1-1:1.0: 4 ports detected [ 2.010000] NET: Registered protocol family 1 [ 2.080000] usb 1-1.1: new full speed USB device using ehci_marvell and address 3 [ 2.180000] usb 1-1.1: configuration #1 chosen from 1 choice [ 2.320000] usbcore: registered new interface driver hiddev [ 2.460000] input: Logitech USB Receiver as /class/input/input0 [ 2.460000] input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-ehci_marvell.70059-1.1 [ 2.500000] input: Logitech USB Receiver as /class/input/input1 [ 2.500000] input,hiddev96: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-ehci_marvell.70059-1.1 [ 2.540000] hiddev97: USB HID v1.11 Device [Logitech USB Receiver] on usb-ehci_marvell.70059-1.1 [ 2.540000] usbcore: registered new interface driver usbhid [ 2.540000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 4.890000] EXT3 FS on sda1, internal journal [ 7.050000] udevd version 125 started [ 27.700000] NET: Registered protocol family 10 [ 27.700000] lo: Disabled Privacy Extensions [ 27.700000] Mobile IPv6 [ 35.290000] XGIfb: Change mode to 1024x768x16-60Hz [ 35.630000] phys_mem_access_prot called - offset f2001000, uncached_access = -1071249904 [ 37.310000] eth0: link up, full duplex, speed 100 Mbps [ 37.310000] eth0: started [ 37.570000] phys_mem_access_prot called - offset ec000000, uncached_access = -1071249904 [ 37.570000] phys_mem_access_prot called - offset e8000000, uncached_access = -1071249904 [ 48.260000] eth0: no IPv6 routers present [ 649.790000] usb 1-1.2: new high speed USB device using ehci_marvell and address 4 [ 649.890000] usb 1-1.2: configuration #1 chosen from 1 choice [ 650.110000] Initializing USB Mass Storage driver... [ 650.120000] scsi2 : SCSI emulation for USB Mass Storage devices [ 650.120000] usb-storage: device found at 4 [ 650.120000] usb-storage: waiting for device to settle before scanning [ 650.120000] usbcore: registered new interface driver usb-storage [ 650.120000] USB Mass Storage support registered. [ 655.120000] usb-storage: device scan complete [ 655.120000] scsi 2:0:0:0: Direct-Access SanDisk Cruzer 8.02 PQ: 0 ANSI: 0 CCS [ 655.140000] sd 2:0:0:0: [sdb] 3907583 512-byte hardware sectors (2001 MB) [ 655.150000] sd 2:0:0:0: [sdb] Write Protect is off [ 655.150000] sd 2:0:0:0: [sdb] Mode Sense: 45 00 00 08 [ 655.150000] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 655.170000] sd 2:0:0:0: [sdb] 3907583 512-byte hardware sectors (2001 MB) [ 655.190000] sd 2:0:0:0: [sdb] Write Protect is off [ 655.190000] sd 2:0:0:0: [sdb] Mode Sense: 45 00 00 08 [ 655.190000] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 655.190000] sdb: sdb1 [ 655.200000] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 655.730000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
|
Re: HP T5325 Thin Client Debian January 28, 2016 07:01AM |
Admin Registered: 13 years ago Posts: 18,543 |
1. Debian:
We could change these to boot the new rootfs now. But to be safe, we should do that in serial console.
2. U-Boot:
UART booting is important. If UART booting works then this should be a lot easier.
3. One more check (why are we seeing "/etc/fw_env.config: No such file or directory", perhaps this rootfs is too old)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
usb_bootargs=root=/dev/ram rw bootusb=usb start;fatload usb 0 0x800000 /boot/uImage.usb;fatload usb 0 0x1100000 /boot/uInitrd.usb usbboot=setenv bootargs $(usb_bootargs); run bootusb; bootm 0x800000 0x1100000 bootcmd=run thinpro
We could change these to boot the new rootfs now. But to be safe, we should do that in serial console.
2. U-Boot:
UART booting is important. If UART booting works then this should be a lot easier.
3. One more check (why are we seeing "/etc/fw_env.config: No such file or directory", perhaps this rootfs is too old)
dpkg -l | grep u-boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: HP T5325 Thin Client Debian January 28, 2016 08:19AM |
Registered: 9 years ago Posts: 1,037 |
@bodhi
1 & 2
I will attempt the UART boot after solder this weekend - if it doesn't pan out that i can get serial console access in any sensible way. I have no problem "living dangerously" and issuing the commands from a live system...
3 dpkg -l | grep u-boot
and just for fun
Im gonna go with not so much old as "archaic" :)
1 & 2
I will attempt the UART boot after solder this weekend - if it doesn't pan out that i can get serial console access in any sensible way. I have no problem "living dangerously" and issuing the commands from a live system...
3 dpkg -l | grep u-boot
root@HPf4ce462327d3:~# cd / root@HPf4ce462327d3:/# dpkg -l | grep u-boot root@HPf4ce462327d3:/#
and just for fun
root@HPf4ce462327d3:/# uname -a Linux HPf4ce462327d3 2.6.22.18-2-armel #1 PREEMPT Tue Nov 17 13:34:38 EST 2009 armv5tejl GNU/Linux root@HPf4ce462327d3:/etc# cat /etc/debian_version 5.0.5
Im gonna go with not so much old as "archaic" :)
|
Re: HP T5325 Thin Client Debian January 28, 2016 01:15PM |
Admin Registered: 13 years ago Posts: 18,543 |
Gravelrash,
> I will attempt the UART boot after solder this
> weekend - if it doesn't pan out that i can get
> serial console access in any sensible way. I have
> no problem "living dangerously" and issuing the
> commands from a live system...
>
I know :)
The current set of envs looks sane enough that I don't think we gonna get lock out even if we change these in live system. I have not seen stock serial bootlog, so I can only guess: it looks as though this box has been modded before to add USB booting envs. But it does not point to USB rootfs, so I'm so sure, perhaps the previous owner failed to make it boot with USB so it got sold.
>
> Im gonna go with not so much old as "archaic" :)
6 years is ancient!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I will attempt the UART boot after solder this
> weekend - if it doesn't pan out that i can get
> serial console access in any sensible way. I have
> no problem "living dangerously" and issuing the
> commands from a live system...
>
I know :)
The current set of envs looks sane enough that I don't think we gonna get lock out even if we change these in live system. I have not seen stock serial bootlog, so I can only guess: it looks as though this box has been modded before to add USB booting envs. But it does not point to USB rootfs, so I'm so sure, perhaps the previous owner failed to make it boot with USB so it got sold.
>
> Im gonna go with not so much old as "archaic" :)
6 years is ancient!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: HP T5325 Thin Client Debian January 28, 2016 01:48PM |
Registered: 9 years ago Posts: 1,037 |
bodhi Wrote:
-------------------------------------------------------
>
it looks as though this box has been modded before to add USB booting envs. But it does not point to USB rootfs, so I'm so sure, perhaps the previous owner failed to make it boot with USB so it got sold.
>
apparently usb booting on this device is a standard feature, according to the manual for the device, is the way to recover the system and update the "firmware".
I wonder if "Uncle Google" has any answers where i can locate the tools they are talking about and possibly an old image....
(trouble shooting guide) http://h20566.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c01940143
P.S. I cant believe i have just publicly soiled my "man cred" by admitting to reading a manual.....luckily the other half never reads this forum
:) :)
-------------------------------------------------------
>
it looks as though this box has been modded before to add USB booting envs. But it does not point to USB rootfs, so I'm so sure, perhaps the previous owner failed to make it boot with USB so it got sold.
>
apparently usb booting on this device is a standard feature, according to the manual for the device, is the way to recover the system and update the "firmware".
I wonder if "Uncle Google" has any answers where i can locate the tools they are talking about and possibly an old image....
(trouble shooting guide) http://h20566.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c01940143
Creating a Bootable USB Flash Drive Page - 29 To create a bootable USB flash drive for purposes of reflashing or restoring the software image on the onboard flash, see the HP ThinPro Administrator’s Guide, section HP ThinState Utility > Manage the ThinPro Image > Capture HP ThinPro Image to a Bootable USB Flash Drive. NOTE: During the restore process, the thin client flash drive is reformatted and all data is erased before the system image is copied to it. To prevent loss of data, be sure to save any user-created data from the flash drive. Restoring the software image may take approximately five minutes. Booting from a USB Flash Drive To boot the USB flash drive created in the previous section: 1. Power off the unit. 2. Insert the ThinState drive into one of the USB slots on the thin client. 3. Press and release the power button, and then quickly press and release the power button again. 4. After about 15 seconds, the unit beeps and a dialog is displayed verifying that you wish to reimage the device. NOTE: Some USB flash drives may not work. If the unit does not boot from the USB flash drive, try removing all other USB devices and insert the USB flash drive into one of the rear USB ports. If the unit still does not boot from the USB flash drive, try a different flash drive. Restoring a Corrupt uBoot page 30 If uBoot on the thin client is corrupt, the unit will not boot. The unit must be sent back for repair. Updating uBoot To update uBoot: 1. Create a ThinState key as described in Restoring the Flash Image on page 29. 2. Insert the key into a computer. 3. Edit the file settings.ini to set useQuickImageMode to 0. 4. Save the file. 5. Copy the new uBoot binary to the uBoot directory on the USB drive. 6. Safely remove the USB drive from the computer 7. Boot the ThinState USB drive as described in Booting from a USB Flash Drive on page 29. 8. After about 15 seconds, the unit beeps and a menu is displayed. 9. Type 4 to enter “Update uBoot Mode” and follow the on-screen prompts. CAUTION: Do not turn off power or attempt to reboot the computer during the upgrade process.
P.S. I cant believe i have just publicly soiled my "man cred" by admitting to reading a manual.....luckily the other half never reads this forum
:) :)
|
Re: HP T5325 Thin Client Debian January 28, 2016 01:57PM |
Admin Registered: 13 years ago Posts: 18,543 |
> apparently usb booting on this device is a
> standard feature, according to the manual for the
> device, is the way to recover the system and
> update the "firmware".
Cool! it means this is the recovery path if we can't get UART booting to work. It would be educational to see the content of this USB drive.
> P.S. I cant believe i have just publicly soiled my
> "man cred" by admitting to reading a
> manual.....luckily the other half never reads this
> forum
> :) :)
Too late, but tell your other half that sometimes we do RTFM :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> standard feature, according to the manual for the
> device, is the way to recover the system and
> update the "firmware".
Cool! it means this is the recovery path if we can't get UART booting to work. It would be educational to see the content of this USB drive.
> P.S. I cant believe i have just publicly soiled my
> "man cred" by admitting to reading a
> manual.....luckily the other half never reads this
> forum
> :) :)
Too late, but tell your other half that sometimes we do RTFM :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: HP T5325 Thin Client Debian January 28, 2016 02:08PM |
Registered: 9 years ago Posts: 1,037 |
bodhi Wrote:
-------------------------------------------------------
> Cool! it means this is the recovery path if we
> can't get UART booting to work. It would be
> educational to see the content of this USB drive.
"Uncle Google" came up trumps - not only do i have the information I also have the original HP pdf... so first thing when i get home this evening is to attempt the backup following the procedure as described in the manual.
Hopefully time will allow for me to dd the image off the usb disk and ill upload it do dropbox and share it from there if you are inerested??
-------------------------------------------------------
> Cool! it means this is the recovery path if we
> can't get UART booting to work. It would be
> educational to see the content of this USB drive.
"Uncle Google" came up trumps - not only do i have the information I also have the original HP pdf... so first thing when i get home this evening is to attempt the backup following the procedure as described in the manual.
Hopefully time will allow for me to dd the image off the usb disk and ill upload it do dropbox and share it from there if you are inerested??
|
Re: HP T5325 Thin Client Debian January 28, 2016 02:30PM |
Admin Registered: 13 years ago Posts: 18,543 |
Gravelrash,
> Hopefully time will allow for me to dd the image
> off the usb disk and ill upload it do dropbox and
> share it from there if you are inerested??
Sure, only at your convenience, no hurry.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Hopefully time will allow for me to dd the image
> off the usb disk and ill upload it do dropbox and
> share it from there if you are inerested??
Sure, only at your convenience, no hurry.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: HP T5325 Thin Client Debian January 29, 2016 02:58AM |
Registered: 9 years ago Posts: 1,037 |
looking good so far... The creation of the recovery disk went well and i know have the disk ready.
The format of the disk is as follows.
Its a fat32 file system with the below directory structure and files
The format of the disk is as follows.
Its a fat32 file system with the below directory structure and files
gravelrash@40 ~ $ cd /media/gravelrash/HPTC\ Imgr/ gravelrash@40 /media/gravelrash/HPTC Imgr $ ls -R .: boot images init.sh settings.ini uboot ./boot: uImage.dove.usb uImage.usb uInitrd.dove.usb uInitrd.usb ./images: ThinPro-T5A32014-2016-01-28.dd.gz ./uboot: u-boot-3.4.19_V16.bin gravelrash@40 /media/gravelrash/HPTC Imgr $
|
Re: HP T5325 Thin Client Debian January 29, 2016 03:36PM |
Admin Registered: 13 years ago Posts: 18,543 |
Interesting! stock u-boot must have implemented the power button command to start this recovery process (running init.sh script).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: HP T5325 Thin Client Debian January 29, 2016 04:15PM |
Registered: 9 years ago Posts: 1,037 |
|
Re: HP T5325 Thin Client Debian January 29, 2016 04:27PM |
Admin Registered: 13 years ago Posts: 18,543 |
Gravelrash Wrote:
-------------------------------------------------------
> I wonder if thats something that could be used on
> other boxes for making upgrades etc easier....
Sure, for boxes that have button (nsa3xx, nsa3xxs, pogo v4, iconnect, goflex home,...) that could be done. The nsa325 u-boot-2015.10 currently has button capability. You have caused a lightbulb :) which boxes do you have?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> I wonder if thats something that could be used on
> other boxes for making upgrades etc easier....
Sure, for boxes that have button (nsa3xx, nsa3xxs, pogo v4, iconnect, goflex home,...) that could be done. The nsa325 u-boot-2015.10 currently has button capability. You have caused a lightbulb :) which boxes do you have?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: HP T5325 Thin Client Debian January 30, 2016 05:55AM |
Registered: 9 years ago Posts: 1,037 |
|
Re: HP T5325 Thin Client Debian January 30, 2016 08:13AM |
Registered: 9 years ago Posts: 1,037 |
Time to "live dangerously" - wasnt able to solder in the appropriate cable to get a uart boot. or for that matter attempt a kwboot.
but for anyone thats interested - the pinout on the uart port is the same as the Pogoplug - seems to be a standard across the marvel kirkwood range
Looking from the front of the board / device the pins are as follows
along with finding the above out from another forum, dont ask me which one - my laptop threw a wobbly and i couldnt find it again, i managed to find the following piece of uboot log
Q - can we mash netconsole onto this version of uboot? if we can mash the configs to it i can attempt a netconsole log.
Edited 1 time(s). Last edit at 01/30/2016 08:29AM by Gravelrash.
but for anyone thats interested - the pinout on the uart port is the same as the Pogoplug - seems to be a standard across the marvel kirkwood range
Looking from the front of the board / device the pins are as follows
Left ---------------------------> Right || 3.3v Power || Tx || RX || Ground || =========================== Left ---------------------------> Right
along with finding the above out from another forum, dont ask me which one - my laptop threw a wobbly and i couldnt find it again, i managed to find the following piece of uboot log
_ _ .____
| |_| | | _ \
| _ | | (_))
| |-| | | |
|_| |_| |_| ..
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
** BOARD: DB-88F6281A-BP LE
U-Boot 1.1.4 (Nov 27 2009 - 14:25:23) MIC version: 3.4.19-15
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD4E0
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash: 1 MB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: SM22 Firm: I052 Ser#: (03)5526888-20080228
Type: Hard Disk
Capacity: 463.6 MB = 0.4 GB (949536 x 512)
1888432 bytes read
Checking Button Status: off
Checking GotoWOL Status: on, setting to off
.
Un-Protected 1 sectors
Erasing Flash...
.
Erased 1 sectors
Writing to Flash... done
.
Protected 1 sectors
Entering WOL mode
--------------
Scaling down CPU freq
PEX is Powered Off - 2
USB is Powered Off - 3
SDIO is Powered Off (clock only) - 4
TSU is Powered Off (clock only) - 5
XOR0 is Powered Off (clock only) - 8
Audio is Powered Off (clock only) - 9
SATA0 is Powered Off - 14
SATA1 is Powered Off - 15
XOR1 is Powered Off (clock only) - 16
CESA is Powered Off (clock only) - 17
Giga1 is Powered Off (clock only) - 19
TDM is Powered Off (clock only) - 20
Setting PHY interrupt mode
Setting GPIOs as input
Setting GPIOs mask
Setting main high interrupt mask
Checking link...
No link, waiting for cable insertion.
And thats all i could find..
Q - can we mash netconsole onto this version of uboot? if we can mash the configs to it i can attempt a netconsole log.
Edited 1 time(s). Last edit at 01/30/2016 08:29AM by Gravelrash.
|
Re: HP T5325 Thin Client Debian January 30, 2016 08:35AM |
Admin Registered: 13 years ago Posts: 18,543 |
Gravelrash,
1. Perhaps you should try the 3 shirt-pins apprach (to push them in temporarily)?
2. Or try to make a clip on header with something like this:
http://www.ebay.com/itm/10pcs-4-Pin-2-54mm-Single-Row-Right-Angle-Female-Pin-Header-USA-Seller-Free-Ship-/222009548254?hash=item33b0ccddde:g:J3sAAOSwp5JWZZbH
I think you can find a narrower pitch header similar to this, and then use an aligator clip to clam it onto the unpopulated serial port?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
1. Perhaps you should try the 3 shirt-pins apprach (to push them in temporarily)?
2. Or try to make a clip on header with something like this:
http://www.ebay.com/itm/10pcs-4-Pin-2-54mm-Single-Row-Right-Angle-Female-Pin-Header-USA-Seller-Free-Ship-/222009548254?hash=item33b0ccddde:g:J3sAAOSwp5JWZZbH
I think you can find a narrower pitch header similar to this, and then use an aligator clip to clam it onto the unpopulated serial port?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: HP T5325 Thin Client Debian January 30, 2016 08:42AM |
Admin Registered: 13 years ago Posts: 18,543 |
Gravelrash,
> ** BOARD: DB-88F6281A-BP LE
>
> U-Boot 1.1.4 (Nov 27 2009 - 14:25:23) MIC version:
> 3.4.19-15
>
> U-Boot code: 00600000 -> 0067FFF0 BSS: ->
> 006CD4E0
>
> Soc: 88F6281 A0 (DDR2)
> CPU running @ 1200Mhz L2 running @ 400Mhz
> SysClock = 400Mhz , TClock = 200Mhz
Good news. This looks just like any other stock Marvell u-boot. It means high probabilty to build new u-boot for it.
>
> Q - can we mash netconsole onto this version of
> uboot? if we can mash the configs to it i can
> attempt a netconsole log.
No, stock u-boot usually don't have netconsole (I never seen one that does).
UPDATE:
BTW, this stock u-boot is horrible, for rebooting. Looks like it keeps rewriting the envs to NAND at each boot.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 01/30/2016 08:49AM by bodhi.
> ** BOARD: DB-88F6281A-BP LE
>
> U-Boot 1.1.4 (Nov 27 2009 - 14:25:23) MIC version:
> 3.4.19-15
>
> U-Boot code: 00600000 -> 0067FFF0 BSS: ->
> 006CD4E0
>
> Soc: 88F6281 A0 (DDR2)
> CPU running @ 1200Mhz L2 running @ 400Mhz
> SysClock = 400Mhz , TClock = 200Mhz
Good news. This looks just like any other stock Marvell u-boot. It means high probabilty to build new u-boot for it.
>
> Q - can we mash netconsole onto this version of
> uboot? if we can mash the configs to it i can
> attempt a netconsole log.
No, stock u-boot usually don't have netconsole (I never seen one that does).
UPDATE:
BTW, this stock u-boot is horrible, for rebooting. Looks like it keeps rewriting the envs to NAND at each boot.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 01/30/2016 08:49AM by bodhi.
|
Re: HP T5325 Thin Client Debian January 30, 2016 09:11AM |
Admin Registered: 13 years ago Posts: 18,543 |
Living dangerously:
1. Create the latest USB rootfs using Debian-3.18.5-kirkwood-tld-1-rootfs-bodhi.tar.bz2.
In step 4, use the sheevaplug
And remember to label the USB rootfs to rootfs.
2. Boot to stock OS and mount the USB rootfs.
3. Change u-boot envs (the dangerous part is in red):
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
1. Create the latest USB rootfs using Debian-3.18.5-kirkwood-tld-1-rootfs-bodhi.tar.bz2.
In step 4, use the sheevaplug
cat dts/kirkwood-sheevaplug.dtb >> zImage.fdt
And remember to label the USB rootfs to rootfs.
2. Boot to stock OS and mount the USB rootfs.
3. Change u-boot envs (the dangerous part is in red):
fw_setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10'
fw_setenv load_usb 'usb start; ext2load usb 0:1 0x800000 /boot/uImage; ext2load usb 0:1 0x1100000 /boot/uInitrd'
fw_setenv bootcmd_usb 'setenv bootargs $(bootargs_usb); run load_usb; bootm 0x800000 0x1100000
fw_setenv bootcmd 'run bootcmd_usb; run thinpro'
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: HP T5325 Thin Client Debian January 30, 2016 10:29AM |
Registered: 9 years ago Posts: 1,037 |
|
Re: HP T5325 Thin Client Debian January 30, 2016 05:20PM |
Registered: 9 years ago Posts: 1,037 |
Tried the other suggested options. to gain console access, gut feeling is that the "com port" is faulty
Trying the above and issuing the fw_printenv commands worked (after i added the missing ') the disk was inserted and boot attempted.
Im guessing it hung somewhere as after a few minutes there still wasn't anything showing on the network
GOOD NEWS IS that the system rebooted straight back into the HP OS, when the USB key was removed and a power cycle applied
Trying the above and issuing the fw_printenv commands worked (after i added the missing ') the disk was inserted and boot attempted.
Im guessing it hung somewhere as after a few minutes there still wasn't anything showing on the network
GOOD NEWS IS that the system rebooted straight back into the HP OS, when the USB key was removed and a power cycle applied
Project on hold till i go shopping and get a 1.25mm pitch JST cable. PROJECT ON HOLD : 30 - 1 - 2016
|
Re: HP T5325 Thin Client Debian January 30, 2016 05:37PM |
Admin Registered: 13 years ago Posts: 18,543 |
Gravelrash,
> GOOD NEWS IS that the system rebooted
> straight back into the HP OS, when the USB key was
> removed and a power cycle applied
Cool! it means that the stock u-boot deal with the envs the way I expected.
It might be the case that it does not like ext2load. If that's indeed the problem then we'll have to use 2 partition disks.
/boot is in a FAT32 parition and / is in an Ext3 partition. And the FAT32 partition must be the 1st partition.
And these would be
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> GOOD NEWS IS that the system rebooted
> straight back into the HP OS, when the USB key was
> removed and a power cycle applied
Cool! it means that the stock u-boot deal with the envs the way I expected.
It might be the case that it does not like ext2load. If that's indeed the problem then we'll have to use 2 partition disks.
/boot is in a FAT32 parition and / is in an Ext3 partition. And the FAT32 partition must be the 1st partition.
And these would be
fw_setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10' fw_setenv load_usb 'usb start; fatload usb 0:1 0x800000 /boot/uImage; fatload usb 0:1 0x1100000 /boot/uInitrd' fw_setenv bootcmd_usb 'setenv bootargs $(bootargs_usb); run load_usb; bootm 0x800000 0x1100000 fw_setenv bootcmd 'run bootcmd_usb; run thinpro'
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: HP T5325 Thin Client Debian : Project on Hold 30-01-2016 January 30, 2016 05:56PM |
Registered: 9 years ago Posts: 1,037 |
Interesting - the only other time I came across the need to do a split disk setup that was on the Cubieboard 2 and the Raspi
Would i need to make any mods to the following and if so what do you recommend
/etc/fstab
machid = i notice one isnt set anywhere, im guessing that the sheevaplug setup we are "borrowing" will need it?
Just ordered these
http://www.ebay.co.uk/sch/i.html?_from=R40&_trksid=p2050601.m570.l1313.TR0.TRC0.H0.XJST+1.25+4-Pin.TRS0&_nkw=JST+1.25+4-Pin&_sacat=0
Would i need to make any mods to the following and if so what do you recommend
/etc/fstab
machid = i notice one isnt set anywhere, im guessing that the sheevaplug setup we are "borrowing" will need it?
Just ordered these
http://www.ebay.co.uk/sch/i.html?_from=R40&_trksid=p2050601.m570.l1313.TR0.TRC0.H0.XJST+1.25+4-Pin.TRS0&_nkw=JST+1.25+4-Pin&_sacat=0
|
Re: HP T5325 Thin Client Debian : Project on Hold 30-01-2016 January 30, 2016 06:05PM |
Registered: 9 years ago Posts: 1,037 |
|
Re: HP T5325 Thin Client Debian : Project on Hold 30-01-2016 January 30, 2016 06:11PM |
Admin Registered: 13 years ago Posts: 18,543 |
> Interesting - the only other time I came across
> the need to do a split disk setup that was on the
> Cubieboard 2 and the Raspi
Right now it is only a guess. Because the recovery script uses fatload, so my deduction that it might lack ext2load. But if HP actually did remove ext2load then I'd say that it is a bad decision to save some bytes. Hard to say though, because we are blind without serial console.
>
> Would i need to make any mods to the following and
> if so what do you recommend
>
> /etc/fstab
>
Should be the same because we are booting with the label rootfs.
> machid = i notice one isnt set anywhere, im
> guessing that the sheevaplug setup we are
> "borrowing" will need it?
It does not need arcNumber or machid because the DTB is embedded. If we are booting 3.16 then yes, we'll need both.
To confirm this, on a box with FDT rootfs running, and you have serial console. Reboot, interrupt serial console and remove both with setenv, then boot.
>
> Just ordered these
> http://www.ebay.co.uk/sch/i.html?_from=R40&_trksid
> =p2050601.m570.l1313.TR0.TRC0.H0.XJST+1.25+4-Pin.T
> RS0&_nkw=JST+1.25+4-Pin&_sacat=0
Wow, that's a really tiny JST header! So my clip-on header idea is more difficult to do. I wonder if there is a right angle 4-pin header (with female connector) that small?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> the need to do a split disk setup that was on the
> Cubieboard 2 and the Raspi
Right now it is only a guess. Because the recovery script uses fatload, so my deduction that it might lack ext2load. But if HP actually did remove ext2load then I'd say that it is a bad decision to save some bytes. Hard to say though, because we are blind without serial console.
>
> Would i need to make any mods to the following and
> if so what do you recommend
>
> /etc/fstab
>
Should be the same because we are booting with the label rootfs.
> machid = i notice one isnt set anywhere, im
> guessing that the sheevaplug setup we are
> "borrowing" will need it?
It does not need arcNumber or machid because the DTB is embedded. If we are booting 3.16 then yes, we'll need both.
To confirm this, on a box with FDT rootfs running, and you have serial console. Reboot, interrupt serial console and remove both with setenv, then boot.
>
> Just ordered these
> http://www.ebay.co.uk/sch/i.html?_from=R40&_trksid
> =p2050601.m570.l1313.TR0.TRC0.H0.XJST+1.25+4-Pin.T
> RS0&_nkw=JST+1.25+4-Pin&_sacat=0
Wow, that's a really tiny JST header! So my clip-on header idea is more difficult to do. I wonder if there is a right angle 4-pin header (with female connector) that small?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: HP T5325 Thin Client Debian : Project on Hold 30-01-2016 January 30, 2016 06:13PM |
Admin Registered: 13 years ago Posts: 18,543 |
Gravelrash Wrote:
-------------------------------------------------------
> I envisage something like this in the /etc/fstab
>
>
Yes this would be fine. However, in recent kernels, the label rootfs takes precedent for mounting.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> I envisage something like this in the /etc/fstab
>
>
> /dev/sda1 /boot vfat defaults > 0 0 > /dev/sda2 / ext3 defaults,noatime > 0 0 > >
Yes this would be fine. However, in recent kernels, the label rootfs takes precedent for mounting.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: HP T5325 Thin Client Debian : Project on Hold 30-01-2016 January 30, 2016 07:15PM |
Registered: 9 years ago Posts: 1,037 |
