Welcome! Log In Create A New Profile

Advanced

Synology USB-Station 2 ?

Posted by dietgert 
Synology USB-Station 2 ?
November 01, 2016 03:31PM
Hello,

I`ve received a 2nd Synology USB-Station 2 .
Now I wonder which U-Boot fits best ...
Pogoplug V4 ?
Attached the output via serial console (no network configured/attached).

BR
dietgert


---------------------------------------------------------------------------


        __  __                        _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: Synology USB Station LE 

U-Boot 1.1.4 (Jul 23 2010 - 14:15:33) Marvell version: 3.4.27

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CCCE0

Soc: 88F6180 A1 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz 

DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000   size 128MB 
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment

[1024kB@f8000000] Flash:  1 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled 
Write allocate disabled


USB 0: host mode

Synology model: DS011jr0

Net:   egiga0 [PRIME]
Press Ctrl+C to abort autoboot in 1 second
(Re)start USB...
USB:   scanning bus for devices... 3 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
.
.....

65536 bytes read
            MAC1: 001132086353
            MAC2: Empty or Invalid checksum (Random: 00e9724c3384)
          Serial: ABHFN01905
   Custom Serial: Empty or Invalid checksum
.
.........................
.........................
.........................
.........................
.........................
.........................
.........................
.....

1899484 bytes read
.
.........................
.........................

540860 bytes read
## Booting image at 01000000 ...
   Image Name:   Linux-2.6.32.12
   Created:      2014-11-14  16:21:53 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1899420 Bytes =  1.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01400000 ...
   Image Name:   synology_88f6180_us2 1983
   Created:      2014-11-14  16:47:09 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    540796 Bytes = 528.1 kB
   Load Address: 00800000
   Entry Point:  00800000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 2.6.32.12 (root@build1) (gcc version 4.2.1) #1983 Sat Nov 15 00:21:50 CST 2014
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Feroceon-KW
[    0.000000] Using UBoot passing parameters structure
[    0.000000] Sys Clk = 200000000, Tclk = 166666667
[    0.000000] Synology Board ID: 22
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 initrd=0x1400040 root=/dev/synoboot1 rootdelay=10 syno_hw_version=DS011jr0 netif_num=1 mac1=001132086353 mac2=00e9724c3384 sn=ABHFN01905 
[    0.000000] Synology Hareware Version: DS011jr0-j
[    0.000000] Internal netif num: 1
[    0.000000] Mac1: 001132086353
[    0.000000] Mac2: 00e9724c3384
[    0.000000] Serial Number: ABHFN01905
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 117800KB available (3396K code, 525K data, 112K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 794.62 BogoMIPS (lpj=3973120)
[    0.230000] Mount-cache hash table entries: 512
[    0.230000] CPU: Testing write buffer coherency: ok
[    0.230000] NET: Registered protocol family 16
[    0.230000] Feroceon L2: Enabling L2
[    0.230000] Feroceon L2: Cache support initialised.
[    0.230000] 
[    0.230000] CPU Interface
[    0.230000] -------------
[    0.230000] SDRAM_CS0 ....base 00000000, size 128MB 
[    0.230000] SDRAM_CS1 ....disable
[    0.230000] SDRAM_CS2 ....disable
[    0.230000] SDRAM_CS3 ....disable
[    0.230000] PEX0_MEM ....base e0000000, size 128MB 
[    0.230000] PEX0_IO ....base f2000000, size   1MB 
[    0.230000] PEX1_MEM ....no such
[    0.230000] PEX1_IO ....no such
[    0.230000] INTER_REGS ....base f1000000, size   1MB 
[    0.230000] NFLASH_CS ....base fa000000, size   2MB 
[    0.230000] SPI_CS ....base f4000000, size  16MB 
[    0.230000] BOOT_ROM_CS ....no such
[    0.230000] DEV_BOOTCS ....no such
[    0.230000] CRYPT_ENG ....base f0000000, size   2MB 
[    0.230000]  Detected Tclk 166666667 and SysClk 200000000 
[    0.230000] Synology 6180 GPIO Init
[    0.730000] PEX0 interface detected no Link.
[    0.730000] PCI: bus0: Fast back to back transfers enabled
[    0.730000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
[    0.740000] bio: create slab <bio-0> at 0
[    0.740000] vgaarb: loaded
[    0.740000] SCSI subsystem initialized
[    0.740000] usbcore: registered new interface driver usbfs
[    0.750000] usbcore: registered new interface driver hub
[    0.750000] usbcore: registered new device driver usb
[    0.750000] Switching to clocksource kw_clocksource
[    0.750000] NET: Registered protocol family 2
[    0.750000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.750000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.750000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.750000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.750000] TCP reno registered
[    0.750000] NET: Registered protocol family 1
[    0.750000] RPC: Registered udp transport module.
[    0.750000] RPC: Registered tcp transport module.
[    0.750000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.750000] Trying to unpack rootfs image as initramfs...
[    2.130000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[    2.130000] Freeing initrd memory: 528K
[    2.130000] XOR registered 4 channels
[    2.130000] XOR 2nd invalidate WA enabled
[    2.130000] VFS: Disk quotas dquot_6.5.2
[    2.130000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    2.130000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.140000] NTFS driver 2.1.29 [Flags: R/O].
[    2.140000] aufs 2-standalone.tree-32-20100419
[    2.140000] msgmni has been set to 231
[    2.140000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    2.140000] io scheduler noop registered
[    2.140000] io scheduler anticipatory registered (default)
[    2.150000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    2.160000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[    2.170000] console [ttyS0] enabled
[    2.170000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[   12.190000] brd: module loaded
[   12.190000] Loading Marvell Ethernet Driver:
[   12.200000]   o Cached descriptors in DRAM
[   12.200000]   o DRAM SW cache-coherency
[   12.210000]   o 2 Giga ports supported
[   12.210000]   o Single RX Queue support - ETH_DEF_RXQ=0
[   12.220000]   o Single TX Queue support - ETH_DEF_TXQ=0
[   12.220000]   o TCP segmentation offload (TSO) supported
[   12.230000]   o Receive checksum offload supported
[   12.230000]   o Transmit checksum offload supported
[   12.240000]   o Rx descripors: q0=128
[   12.240000]   o Tx descripors: q0=532
[   12.240000]   o Loading network interface(s):
[   12.250000]     o  register under mv88fx_eth platform
[   12.260000]     o eth0, ifindex = 2, GbE port = 0
[   12.260000]     o eth0, phy chipid = 1410e40, Support WOL = 0
[   12.270000] 
[   12.270000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   12.270000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[   12.280000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   12.320000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   12.340000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   12.340000] usb usb1: configuration #1 chosen from 1 choice
[   12.350000] hub 1-0:1.0: USB hub found
[   12.350000] hub 1-0:1.0: 1 port detected
[   12.360000] Initializing USB Mass Storage driver...
[   12.360000] usbcore: registered new interface driver usb-storage
[   12.370000] USB Mass Storage support registered.
[   12.370000] usbcore: registered new interface driver hiddev
[   12.380000] usbcore: registered new interface driver usbhid
[   12.380000] usbhid: v2.6:USB HID core driver
[   12.390000] TCP cubic registered
[   12.390000] NET: Registered protocol family 17
[   12.400000] Waiting 10sec before mounting root device...
[   12.680000] usb 1-1: new high speed USB device using orion-ehci and address 2
[   12.830000] usb 1-1: configuration #1 chosen from 1 choice
[   12.830000] hub 1-1:1.0: USB hub found
[   12.840000] hub 1-1:1.0: 4 ports detected
[   12.840000] Got empty serial number. Generate serial number from product.
[   13.120000] usb 1-1.1: new high speed USB device using orion-ehci and address 3
[   13.250000] usb 1-1.1: configuration #1 chosen from 1 choice
[   13.260000] scsi0 : SCSI emulation for USB Mass Storage devices
[   18.270000] scsi 0:0:0:0: Direct-Access     Synology USBstation       1.0  PQ: 0 ANSI: 2
[   18.270000] drivers/scsi/sd.c (2308) Got USB disk
[   18.280000] sd 0:0:0:0: [synoboot] 250880 512-byte logical blocks: (128 MB/122 MiB)
[   18.290000] sd 0:0:0:0: [synoboot] Write Protect is off
[   18.290000] sd 0:0:0:0: [synoboot] Assuming drive cache: write through
[   18.300000] sd 0:0:0:0: [synoboot] Assuming drive cache: write through
[   18.310000]  synoboot: synoboot1 synoboot2 synoboot3
[   28.410000] sd 0:0:0:0: [synoboot] Assuming drive cache: write through
[   28.410000] sd 0:0:0:0: [synoboot] Attached SCSI disk
[   28.420000] RAMDISK: lzma image found at block 0
[   29.930000] VFS: Mounted root (ext2 filesystem) on device 1:0.
START /linuxrc.syno
DISKLESS model
none /sys sysfs rw,relatime 0 0
linuxrc.syno executed successfully.
[   30.070000] VFS: Mounted root (squashfs filesystem) readonly on device 135:241.
[   30.080000] Trying to move old root to /initrd ... okay
[   30.090000] Freeing init memory: 112K
[   30.690000] kjournald starting.  Commit interval 5 seconds
[   30.730000] EXT3 FS on synoboot3, internal journal
[   30.740000] EXT3-fs: synoboot3: 21 orphan inodes deleted
[   30.750000] EXT3-fs: recovery complete.
[   30.860000] EXT3-fs: mounted filesystem with ordered data mode.
[   31.190000] aufs test_add:248:mount[362]: uid/gid/perm /volume1 0/0/0777, 0/0/0755
Prepare var...
Mounting proc filesystem...
Mounting devpts
Starting /etc/rc ...
Check new disk...
Not new disk. Do nothing.
/dev/root on / type squashfs (ro,relatime)
/tmp on /tmp type tmpfs (0)
none on /dev/pts type devpts (gid=4,mode=620)
Hostname USBStation2
192.168.178.24	USBStation2
Load llc.ko... 
Load psnap.ko... 
Load sg.ko... 
[   32.270000] sd 0:0:0:0: Attached scsi generic sg0 type 0
Load crc-ccitt.ko... 
Load crypto_algapi.ko... 
Load crypto_wq.ko... 
Load crypto_blkcipher.ko... 
Load crypto_hash.ko... 
Load aead.ko... 
Load pcompress.ko... 
Load cryptomgr.ko... 
Load cbc.ko... 
Load md5.ko... 
[   32.640000] alg: No test for md5 (md5-generic)
Load aes_generic.ko... 
[   32.680000] alg: No test for aes (aes-generic)
Load rng.ko... 
Load ansi_cprng.ko... 
[   32.730000] alg: No test for stdrng (ansi_cprng)
Load krng.ko... 
[   32.750000] alg: No test for stdrng (krng)
Load eseqiv.ko... 
Load des_generic.ko... 
[   32.800000] alg: No test for des (des-generic)
[   32.810000] alg: No test for des3_ede (des3_ede-generic)
Load chainiv.ko... 
Load ocf.ko... 
[   32.870000] ocf: module license 'BSD' taints kernel.
[   32.880000] Disabling lock debugging due to kernel taint
Load cryptodev.ko... 
Load cesa_dev.ko... 
[   32.940000] cesadev_init(bf0ae000)
Load cesa_ocf_drv.ko... 
[   33.000000] mvCesaInit: sessions=10240, queue=64, pSram=f0000000
Load ecb.ko... 
Load sha1_generic.ko... 
[   33.080000] alg: No test for sha1 (sha1-generic)
Load sha256_generic.ko... 
[   33.100000] alg: No test for sha224 (sha224-generic)
[   33.100000] alg: No test for sha256 (sha256-generic)
Load sha512_generic.ko... 
[   33.140000] alg: No test for sha384 (sha384-generic)
[   33.140000] alg: No test for sha512 (sha512-generic)
Load cryptosoft.ko... 
Load fuse.ko... 
[   33.380000] fuse init (API version 7.13)
Load ipv6.ko... 
[   33.840000] NET: Registered protocol family 10
[   33.840000] lo: Disabled Privacy Extensions
Mounting sysfs...
Mounting usbfs...
Load synobios.ko... 
[   33.900000] synobios: load, major number 201
[   33.910000] Brand: Synology
[   33.910000] Model: DS-011j
synochecknetworkcfg: Pass 

[   34.130000] eth0: mac address changed
[   36.220000] eth0: started
[   36.230000] ADDRCONF(NETDEV_UP): eth0: link is not ready
eth0      Link encap:Ethernet  HWaddr 00:11:32:08:63:53  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:532 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:11 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

kernel.panic = 3
Starting syslogd...
Pass s00_synocheckfstab ...
Pass CheckSynoinfo ...
Pass CheckUser
Pass CheckSmbConf ...
Pass CheckCronTab ...
Pass CheckGroup.
Pass s62_synocheckapple ...
Checking and Mounting filesystem(s) ...
start findhostd
synokerneltz: set kernel time zone to 480
kernel.core_pattern = /var/services/pgsql/../@%e.core
fs.suid_dumpable = 2
vm.min_free_kbytes = 8192
Starting scemd ...
No rules exists, remove firewall modules...
IPv6 Firewall modules has not been started...
Firewall modules has not been started...
rm: can't remove '/tmp/.db.*': No such file or directory
synocheckshare: Pass SYNOICheckShare()
synocheckshare: Pass SYNOICheckShareExt()
synocheckshare: Pass SYNOICheckServiceLink()
synocheckshare: Pass SYNOICheckAutoDecrypt()
synocheckshare: Pass SYNOIServiceShareEnableDefaultUS()
synobootup: BEGIN
synobootup: END
Starting Hotplug Handling Daemon ...
Starting inetd...
Starting crond...
MySQL is not enabled. Skip...
PGSQL service is disabled. Skip...
PGSQL service is disabled. Skip...
19 May 12:15:56 ntpdate[1187]: can't find host pool.ntp.org
19 May 12:15:56 ntpdate[1187]: no servers can be used, exiting
CUPS: Starting cupsd...
GCP: start gcpd..
No related services are supported. Skip...
PGSQL service is disabled. Skip...
#####Remove Temp TDB#####
###Starting nmbd###

##################
 Starting Samba
##################
#####Checking TDB /usr/syno/etc/private/secrets.tdb
backup tdb /usr/syno/etc/private/secrets.tdb
#####Checking TDB /var/run/account_policy.tdb
backup tdb /var/run/account_policy.tdb
#####Checking TDB /var/run/group_mapping.tdb
#####Checking TDB /var/run/ntdrivers.tdb
backup tdb /var/run/ntdrivers.tdb
#####Checking TDB /var/run/ntforms.tdb
backup tdb /var/run/ntforms.tdb
#####Checking TDB /var/run/ntprinters.tdb
backup tdb /var/run/ntprinters.tdb
#####Checking TDB /var/run/share_info.tdb
backup tdb /var/run/share_info.tdb
#####Checking TDB /var/run/registry.tdb
backup tdb /var/run/registry.tdb
Load usblp.ko... 
[   53.880000] usbcore: registered new interface driver usblp
Local package initialization:startup daemons
.

done.
Thr May 19 12:16:03 PDT 1955

USBStation2 login: Starting Netatalk services (this will take a while): 
 cnid_metad afpd (USBStation2:AFPServer).
PGSQL service is disabled. Skip...
cp: can't stat '/var.defaults/spool/postfix': No such file or directory
chmod: /volume1/@postfix/public: No such file or directory
Start SSH...
Audio Station is not enabled. Skip...
Audio Station is not enabled. Skip...
Start System Apache Server .....  -DREDIRECT_USER -f /usr/syno/apache/conf/httpd.conf-sys
/usr/syno/etc/rc.d/S97apache-sys.sh: system httpd started
start findhostd
/var/spool/synoeaupgrade.list doesn't exist!
Stop upgarde
Starting Avahi mDNS/DNS-SD Daemon
Process 2043 died: No such process; trying to remove PID file. (/var/run/avahi-daemon//pid)
PGSQL is not enabled
cat: can't open '/sys/block/sd*/device/model': No such file or directory
19 May 12:16:06 ntpdate[1187]: no servers can be used, exiting
[   60.040000] Unhandled msg num 00005202
19 May 12:16:16 ntpdate[1187]: no servers can be used, exiting
19 May 12:16:26 ntpdate[1187]: no servers can be used, exiting
....

USBStation2 login:

edit 110216: original printenv added:


Marvell>> printenv
bootcmd=set bootargs console=ttyS0,115200 initrd=0x1400040 root=/dev/synoboot1 rootdelay=10 syno_hw_version=DS011jr0 netif_num=1; usb start; vendor usb 0:2 /vender; ext2load usb 0:2 1000000 /zImage; ext2load usb 0:2 1400000 /rd.bin; bootm 1000000 1400000
baudrate=115200
loads_echo=0
ipaddr=192.168.101.224
serverip=192.168.101.111
rootpath=/mnt/ARM_FS/
netmask=255.255.0.0
run_diag=yes
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=spi_flash:0x80000@0(uboot)ro,0x300000@0x100000(root)
mainlineLinux=no
CASset=min
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
MALLOC_len=1
ethprime=egiga0
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:egiga0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
bootdelay=1
disaMvPnp=no
ethaddr=00:50:43:xx:xx:xx
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
pcieTune=no
bootargs=console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS011jr0 ihd_num=2 netif_num=1
ethact=egiga0

Environment size: 1341/4092 bytes



Edited 4 time(s). Last edit at 11/02/2016 04:47AM by dietgert.
Re: Synology USB-Station 2 ?
November 01, 2016 08:32PM
None in my supported uboots is a close match for this box. However, the Pogo V4 is the closest. Try UART booting with kwboot using the PogoV4 uboot.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: Synology USB-Station 2 ?
November 02, 2016 04:55AM
bodhi Wrote:
-------------------------------------------------------
> None in my supported uboots is a close match for
> this box. However, the Pogo V4 is the closest. Try
> UART booting with kwboot using the PogoV4 uboot.

OK, assumed that too.
With your procedure from:
http://forum.doozan.com/read.php?3,7852,16859#msg-16859
kwboot works.
Output (your 4.4.0 rootfs) - with USB-Stick in the lower slot - below.

BR
dietgert

Sending boot image...
  0 % [......................................................................]
  
   ---->
 
 99 % [....................................]
[Type Ctrl-\ + c to quit]


U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  0 MiB                                                                                     <---- ??????
MMC:   kwsdio: 0
*** Warning - readenv() failed, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   egiga0
PHY reset timed out
Hit any key to stop autoboot:  0 
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
       scanning usb for storage devices... 2 Storage Device(s) found

Reset IDE: ide_preinit failed

Partition Map for USB device 0  --   Partition Type: DOS

Part	Start Sector	Num Sectors	UUID		Type
  1	2048      	62650368  	bb81df54-01	83


Partition Map for USB device 1  --   Partition Type: DOS

Part	Start Sector	Num Sectors	UUID		Type
  1	31488     	211712    	0de025fb-01	83
  2	243200    	7680      	0de025fb-02	83
  3	16        	31472     	0de025fb-03	83
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **

no IDE devices available
3165142 bytes read in 387 ms (7.8 MiB/s)
7179935 bytes read in 456 ms (15 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-4.4.0-kirkwood-tld-1
   Created:      2016-11-02   9:07:40 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3165078 Bytes = 3 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-4.4.0-kirkwood-tld-1
   Created:      2016-02-19   7:33:04 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7179871 Bytes = 6.8 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
Using machid 0xf78 from environment

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine model: Pogoplug v4
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 113632K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17440K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc07d7ef4   (8000 kB)
[    0.000000]       .init : 0xc07d8000 - 0xc0822000   ( 296 kB)
[    0.000000]       .data : 0xc0822000 - 0xc08b169c   ( 574 kB)
[    0.000000]        .bss : 0xc08b169c - 0xc08ff9d0   ( 313 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[    0.000014] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[    0.000499] Console: colour dummy device 80x30
[    0.000547] Calibrating delay loop... 789.70 BogoMIPS (lpj=3948544)
[    0.040126] pid_max: default: 32768 minimum: 301
[    0.040293] Security Framework initialized
[    0.040407] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040439] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.041652] Initializing cgroup subsys io
[    0.041704] Initializing cgroup subsys devices
[    0.041740] Initializing cgroup subsys freezer
[    0.041789] Initializing cgroup subsys net_cls
[    0.041917] CPU: Testing write buffer coherency: ok
[    0.042627] Setting up static identity map for 0x8200 - 0x8258
[    0.043090] mvebu-soc-id: MVEBU SoC ID=0x6180, Rev=0x3
[    0.048805] devtmpfs: initialized
[    0.055864] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.056571] prandom: seed boundary self test passed
[    0.062330] prandom: 100 self tests passed
[    0.062388] pinctrl core: initialized pinctrl subsystem
[    0.064533] NET: Registered protocol family 16
[    0.065280] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.090167] cpuidle: using governor ladder
[    0.120164] cpuidle: using governor menu
[    0.120831] Feroceon L2: Enabling L2
[    0.120896] Feroceon L2: Cache support initialised.
[    0.121465] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[    0.129073] No ATAGs?
[    0.162314] vgaarb: loaded
[    0.162837] usbcore: registered new interface driver usbfs
[    0.162956] usbcore: registered new interface driver hub
[    0.163074] usbcore: registered new device driver usb
[    0.164712] clocksource: Switched to clocksource orion_clocksource
[    0.246760] NET: Registered protocol family 2
[    0.247949] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.247989] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.248019] TCP: Hash tables configured (established 1024 bind 1024)
[    0.248122] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.248158] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.248437] NET: Registered protocol family 1
[    0.249022] RPC: Registered named UNIX socket transport module.
[    0.249040] RPC: Registered udp transport module.
[    0.249051] RPC: Registered tcp transport module.
[    0.249063] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.249470] Unpacking initramfs...
[    1.204810] Freeing initrd memory: 7012K (c1100000 - c17d9000)
[    1.205026] NetWinder Floating Point Emulator V0.97 (double precision)
[    1.206650] futex hash table entries: 256 (order: -1, 3072 bytes)
[    1.206758] audit: initializing netlink subsys (disabled)
[    1.206834] audit: type=2000 audit(1.200:1): initialized
[    1.207337] Initialise system trusted keyring
[    1.207922] zbud: loaded
[    1.208343] VFS: Disk quotas dquot_6.6.0
[    1.208427] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.209220] NFS: Registering the id_resolver key type
[    1.209297] Key type id_resolver registered
[    1.209311] Key type id_legacy registered
[    1.209349] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.209370] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.209697] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.210448] Key type big_key registered
[    1.240069] Key type asymmetric registered
[    1.240103] Asymmetric key parser 'x509' registered
[    1.240252] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.240283] io scheduler noop registered
[    1.240306] io scheduler deadline registered
[    1.240398] io scheduler cfq registered (default)
[    1.241728] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 36
[    1.241752] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 37
[    1.241770] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 38
[    1.241788] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 39
[    1.241805] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 40
[    1.241823] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 41
[    1.241840] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 42
[    1.241858] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 43
[    1.241875] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 44
[    1.241893] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 45
[    1.241910] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 46
[    1.241928] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47
[    1.241945] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 48
[    1.241963] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49
[    1.242462] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    1.243450] irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated
[    1.244061] irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated
[    1.245644] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00
[    1.245674] pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
[    1.245695] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[    1.245716] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.246305] PCI: bus0: Fast back to back transfers disabled
[    1.246344] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.246651] PCI: bus1: Fast back to back transfers enabled
[    1.246785] pci 0000:00:01.0: PCI bridge to [bus 01]
[    1.247273] mv_xor f1060800.xor: Marvell shared XOR driver
[    1.285750] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    1.286091] mv_xor f1060900.xor: Marvell shared XOR driver
[    1.325723] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    1.326446] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.328574] console [ttyS0] disabled
[    1.328665] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A
[    2.075517] console [ttyS0] enabled
[    2.324842] nand: No NAND device found
[    2.328597] Unable to handle kernel NULL pointer dereference at virtual address 00000200
[    2.336681] pgd = c0004000
[    2.339374] [00000200] *pgd=00000000
[    2.342950] Internal error: Oops: 805 [#1] PREEMPT ARM
[    2.348065] Modules linked in:
[    2.351122] CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.0-kirkwood-tld-1 #1
[    2.358054] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[    2.364295] task: c783bb20 ti: c783c000 task.ti: c783c000
[    2.369674] PC is at __clk_put+0x50/0xe8
[    2.373596] LR is at clk_prepare_lock+0xc/0xd4
[    2.378026] pc : [<c04c2c68>]    lr : [<c04bf6a0>]    psr: 20000013
[    2.378026] sp : c783de20  ip : 00000002  fp : 00000000
[    2.389453] r10: 00000000  r9 : c1017350  r8 : c78ca400
[    2.394655] r7 : ffffffed  r6 : c101aa00  r5 : c1017010  r4 : c101aa00
[    2.401151] r3 : 00000100  r2 : 00000200  r1 : 00000001  r0 : 00000001
[    2.407651] Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[    2.414751] Control: 0005397f  Table: 01038000  DAC: 00000053
[    2.420470] Process swapper (pid: 1, stack limit = 0xc783c190)
[    2.426277] Stack: (0xc783de20 to 0xc783e000)
[    2.430624] de20: 00000000 fffffffa c1017010 c0805d28 c07541a6 c78d1da8 c10be038 00000019
[    2.438769] de40: 00000000 00000000 ffffffed c78ca410 c088f4c4 00000000 c08ab388 00000000
[    2.446919] de60: c08b16a0 c03edf94 c78ca410 c088f4c4 c08f7fa0 c03ec178 c088f4c4 c78ca410
[    2.455066] de80: 00000001 c78ca410 c78ca444 c088f4c4 c088a218 c08ab2b0 c0815838 c03ec464
[    2.463214] dea0: 00000000 c088f4c4 c03ec3fc c03ea5f8 c788caec c78d0e50 c088f4c4 00000000
[    2.471361] dec0: c67f2dc0 c03eb74c c0741431 c0741432 c088f4c4 c0805aac 00000001 c0828000
[    2.479510] dee0: c0828000 c03ecf1c c03eded8 c088f4b0 c0805aac c03ee178 c101ac40 c0805aac
[    2.487656] df00: 00000000 c00097a0 c7804c40 c782d680 c782d680 c05b7e0c 00000000 c7ffca41
[    2.495803] df20: c7ffca4a c0037c58 00000000 60000053 00000001 c07a6b8c 0000008b 00000006
[    2.503950] df40: 00000006 c07a7668 0000008a c07a7668 c082b788 00000006 c081582c 00000006
[    2.512099] df60: c0815830 0000008b c08208fc c08b16a0 c0815838 c07d8e20 00000006 00000006
[    2.520245] df80: 00000000 c07d85a0 00000000 c05b16ac 00000000 00000000 00000000 00000000
[    2.528392] dfa0: 00000000 c05b16b4 00000000 c000f090 00000000 00000000 00000000 00000000
[    2.536539] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    2.544687] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 00407ffa 00027ddf
[    2.552853] [<c04c2c68>] (__clk_put) from [<c0805d28>] (orion_nand_probe+0x264/0x2a0)
[    2.560661] [<c0805d28>] (orion_nand_probe) from [<c03edf94>] (platform_drv_probe+0x50/0xa0)
[    2.569072] [<c03edf94>] (platform_drv_probe) from [<c03ec178>] (driver_probe_device+0x18c/0x410)
[    2.577917] [<c03ec178>] (driver_probe_device) from [<c03ec464>] (__driver_attach+0x68/0x8c)
[    2.586333] [<c03ec464>] (__driver_attach) from [<c03ea5f8>] (bus_for_each_dev+0x6c/0x90)
[    2.594486] [<c03ea5f8>] (bus_for_each_dev) from [<c03eb74c>] (bus_add_driver+0x114/0x240)
[    2.602724] [<c03eb74c>] (bus_add_driver) from [<c03ecf1c>] (driver_register+0x9c/0xe0)
[    2.610698] [<c03ecf1c>] (driver_register) from [<c03ee178>] (__platform_driver_probe+0x4c/0xe8)
[    2.619452] [<c03ee178>] (__platform_driver_probe) from [<c00097a0>] (do_one_initcall+0x114/0x1d8)
[    2.628389] [<c00097a0>] (do_one_initcall) from [<c07d8e20>] (kernel_init_freeable+0x18c/0x258)
[    2.637068] [<c07d8e20>] (kernel_init_freeable) from [<c05b16b4>] (kernel_init+0x8/0xe4)
[    2.645135] [<c05b16b4>] (kernel_init) from [<c000f090>] (ret_from_fork+0x14/0x24)
[    2.652679] Code: ebfff28d e5943014 e5942018 e3530000 (e5823000) 
[    2.658825] ---[ end trace ac1c4f0c123bce78 ]---
[    2.663454] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[    2.663454] 
[    2.672557] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[    2.672557]



Edited 3 time(s). Last edit at 11/02/2016 10:40AM by dietgert.
Re: Synology USB-Station 2 ?
November 02, 2016 05:15AM
and here the output of arch-Linux as well:

Sending boot image...
  0 % [......................................................................]
 
         ---->

 99 % [....................................]
[Type Ctrl-\ + c to quit]


U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  0 MiB
MMC:   kwsdio: 0
*** Warning - readenv() failed, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   egiga0
PHY reset timed out
Hit any key to stop autoboot:  0 
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
       scanning usb for storage devices... 2 Storage Device(s) found

Reset IDE: ide_preinit failed

Partition Map for USB device 0  --   Partition Type: DOS

Part	Start Sector	Num Sectors	UUID		Type
  1	2048      	15628288  	1562cb61-01	83


Partition Map for USB device 1  --   Partition Type: DOS

Part	Start Sector	Num Sectors	UUID		Type
  1	31488     	211712    	0de025fb-01	83
  2	243200    	7680      	0de025fb-02	83
  3	16        	31472     	0de025fb-03	83
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **

no IDE devices available
4603360 bytes read in 308 ms (14.3 MiB/s)
** File not found /boot/uInitrd **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-4.4.28-1-ARCH
   Created:      2016-10-29   6:28:08 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4603296 Bytes = 4.4 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
Using machid 0xf78 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.28-1-ARCH (builduser@leming) (gcc version 6.2.1 20160830 (GCC) ) #1 PREEMPT Sat Oct 29 00:27:49 MDT 2016
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Pogoplug V4
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 119696K/131072K available (6597K kernel code, 547K rwdata, 1876K rodata, 300K init, 725K bss, 11376K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc084e9a4   (8475 kB)
[    0.000000]       .init : 0xc084f000 - 0xc089a000   ( 300 kB)
[    0.000000]       .data : 0xc089a000 - 0xc0922e0c   ( 548 kB)
[    0.000000]        .bss : 0xc0922e0c - 0xc09d83d8   ( 726 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:114
[    0.000019] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[    9.015845] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[    9.016130] Console: colour dummy device 80x30
[    9.016172] Calibrating delay loop... 789.70 BogoMIPS (lpj=3948544)
[    9.055934] pid_max: default: 32768 minimum: 301
[    9.056077] Security Framework initialized
[    9.056186] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    9.056211] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    9.057331] Initializing cgroup subsys io
[    9.057380] Initializing cgroup subsys memory
[    9.057461] Initializing cgroup subsys devices
[    9.057499] Initializing cgroup subsys freezer
[    9.057530] Initializing cgroup subsys net_cls
[    9.057557] Initializing cgroup subsys perf_event
[    9.057590] Initializing cgroup subsys net_prio
[    9.057712] CPU: Testing write buffer coherency: ok
[    9.058400] Setting up static identity map for 0x81e0 - 0x8238
[    9.061352] devtmpfs: initialized
[    9.064914] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    9.065645] pinctrl core: initialized pinctrl subsystem
[    9.066933] NET: Registered protocol family 16
[    9.067718] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    9.095975] cpuidle: using governor ladder
[    9.125976] cpuidle: using governor menu
[    9.126244] Kirkwood: MV88F6180-Rev-A1, TCLK=166666667.
[    9.126280] Feroceon L2: Enabling L2
[    9.126333] Feroceon L2: Cache support initialised.
[    9.127471] orion_mpp_conf: requested MPP27 config unavailable on this hardware
[    9.127482] orion_mpp_conf: requested MPP29 config unavailable on this hardware
[    9.127492] orion_mpp_conf: requested MPP22 config unavailable on this hardware
[    9.127501] orion_mpp_conf: requested MPP24 config unavailable on this hardware
[    9.129770] Kirkwood PCIe port 0: link down
[    9.129786] PCI: bus0 uses PCIe port 0
[    9.130126] PCI host bridge to bus 0000:00
[    9.130152] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[    9.130169] pci_bus 0000:00: root bus resource [io  0x1000-0xffff]
[    9.130185] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    9.130711] PCI: bus0: Fast back to back transfers disabled
[    9.168144] vgaarb: loaded
[    9.168612] SCSI subsystem initialized
[    9.169346] usbcore: registered new interface driver usbfs
[    9.169457] usbcore: registered new interface driver hub
[    9.169543] usbcore: registered new device driver usb
[    9.169793] pps_core: LinuxPPS API ver. 1 registered
[    9.169807] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    9.169856] PTP clock support registered
[    9.171491] clocksource: Switched to clocksource orion_clocksource
[    9.228924] FS-Cache: Loaded
[    9.247881] NET: Registered protocol family 2
[    9.249057] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    9.249096] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    9.249125] TCP: Hash tables configured (established 1024 bind 1024)
[    9.249232] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    9.249268] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    9.249541] NET: Registered protocol family 1
[    9.250008] RPC: Registered named UNIX socket transport module.
[    9.250025] RPC: Registered udp transport module.
[    9.250034] RPC: Registered tcp transport module.
[    9.250044] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    9.253104] futex hash table entries: 256 (order: -1, 3072 bytes)
[    9.272203] VFS: Disk quotas dquot_6.6.0
[    9.272599] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    9.275646] FS-Cache: Netfs 'nfs' registered for caching
[    9.277328] NFS: Registering the id_resolver key type
[    9.277398] Key type id_resolver registered
[    9.277410] Key type id_legacy registered
[    9.277528] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    9.279468] fuse init (API version 7.23)
[    9.282744] aufs 4.4-20160912
[    9.290303] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    9.290339] io scheduler noop registered
[    9.290361] io scheduler deadline registered
[    9.290758] io scheduler cfq registered
[    9.291151] io scheduler bfq registered (default)
[    9.291163] BFQ I/O-scheduler: v7r11
[    9.291469] mv_xor mv_xor.0: Marvell shared XOR driver
[    9.333443] mv_xor mv_xor.0: Marvell XOR (Registers Mode): ( xor cpy )
[    9.333801] mv_xor mv_xor.1: Marvell shared XOR driver
[    9.373353] mv_xor mv_xor.1: Marvell XOR (Registers Mode): ( xor cpy )
[    9.381653] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    9.383214] console [ttyS0] disabled
[    9.403259] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A
[   10.023603] console [ttyS0] enabled
[   10.050453] brd: module loaded
[   10.064998] loop: module loaded
[   10.068639] sata_mv sata_mv.0: cannot get optional clkdev
[   10.074216] sata_mv sata_mv.0: slots 32 ports 1
[   10.081208] scsi host0: sata_mv
[   10.084941] ata1: SATA max UDMA/133 irq 21
[   10.331639] nand: No NAND device found
[   10.335394] Unable to handle kernel NULL pointer dereference at virtual address 00000200
[   10.343474] pgd = c0004000
[   10.346170] [00000200] *pgd=00000000
[   10.349746] Internal error: Oops: 805 [#1] PREEMPT ARM
[   10.354861] Modules linked in:
[   10.357918] CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.28-1-ARCH #1
[   10.364244] Hardware name: Pogoplug V4
[   10.367979] task: c7890000 ti: c7882000 task.ti: c7882000
[   10.373364] PC is at __clk_put+0x24/0xec
[   10.377268] LR is at clk_prepare_lock+0xc/0xe4
[   10.381694] pc : [<c05545a0>]    lr : [<c0550f10>]    psr: 20000013
[   10.381694] sp : c7883e20  ip : 00000002  fp : 00000000
[   10.393120] r10: 00000000  r9 : c79ba350  r8 : c08a12d0
[   10.398323] r7 : c705b2c0  r6 : fffffffa  r5 : c08a12c0  r4 : c705b2c0
[   10.404819] r3 : 00000100  r2 : 00000200  r1 : 00000001  r0 : 00000001
[   10.411319] Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[   10.418419] Control: 0005397f  Table: 00004000  DAC: 00000053
[   10.424138] Process swapper (pid: 1, stack limit = 0xc7882190)
[   10.429945] Stack: (0xc7883e20 to 0xc7884000)
[   10.434290] 3e20: c79ba010 c08a12c0 fffffffa c0880e9c c7062690 c07b95b8 00000000 00000000
[   10.442437] 3e40: c08a12e0 c08a12e0 c0903d84 fffffdfb 00000000 00000007 c082179c c040e538
[   10.450584] 3e60: c08a12e0 c09cccf8 c0903d84 00000000 00000000 c040c990 c08a12e0 c0903d84
[   10.458731] 3e80: c08a1314 00000000 00000000 c040cb18 00000000 c0903d84 c040ca8c c040acbc
[   10.466880] 3ea0: c783170c c78bced0 c0903d84 c705d1e0 c08f8240 c040becc c0770c50 c038da70
[   10.475027] 3ec0: c0903d84 c0903d84 00000001 00000002 c0903d84 c040d4f4 c0903d70 00000001
[   10.483174] 3ee0: 00000002 c040e714 c089f000 c089f000 c705b240 c0880cb0 00000000 c00096ec
[   10.491323] 3f00: c064faec c09a7da8 c08b3684 00000000 00000000 c0196ed8 00000000 60000053
[   10.499469] 3f20: c7ffca4a c067a0e0 000000be c003c320 00000000 c07b9258 c082179c 00000000
[   10.507617] 3f40: 00000006 00000006 c08aca08 000000be 000000be c089856c c0922e20 c088d830
[   10.515764] 3f60: c0922e20 c082179c 00000000 c084fe40 00000006 00000006 00000000 c084f5a0
[   10.523912] 3f80: 00000000 00000000 c06472a4 00000000 00000000 00000000 00000000 00000000
[   10.532059] 3fa0: 00000000 c06472ac 00000000 c000a4d0 00000000 00000000 00000000 00000000
[   10.540206] 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   10.548354] 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 48447d92 22027eff
[   10.556520] [<c05545a0>] (__clk_put) from [<c0880e9c>] (orion_nand_probe+0x1d4/0x1fc)
[   10.564326] [<c0880e9c>] (orion_nand_probe) from [<c040e538>] (platform_drv_probe+0x34/0x9c)
[   10.572740] [<c040e538>] (platform_drv_probe) from [<c040c990>] (driver_probe_device+0x1f0/0x2ec)
[   10.581578] [<c040c990>] (driver_probe_device) from [<c040cb18>] (__driver_attach+0x8c/0x90)
[   10.589985] [<c040cb18>] (__driver_attach) from [<c040acbc>] (bus_for_each_dev+0x6c/0x9c)
[   10.598131] [<c040acbc>] (bus_for_each_dev) from [<c040becc>] (bus_add_driver+0x100/0x210)
[   10.606367] [<c040becc>] (bus_add_driver) from [<c040d4f4>] (driver_register+0x78/0xf4)
[   10.614341] [<c040d4f4>] (driver_register) from [<c040e714>] (__platform_driver_probe+0x5c/0x120)
[   10.623179] [<c040e714>] (__platform_driver_probe) from [<c00096ec>] (do_one_initcall+0x84/0x1f0)
[   10.632030] [<c00096ec>] (do_one_initcall) from [<c084fe40>] (kernel_init_freeable+0x188/0x254)
[   10.640711] [<c084fe40>] (kernel_init_freeable) from [<c06472ac>] (kernel_init+0x8/0xe8)
[   10.648771] [<c06472ac>] (kernel_init) from [<c000a4d0>] (ret_from_fork+0x14/0x24)
[   10.656311] Code: ebfff25b e5943014 e5942018 e3530000 (e5823000) 
[   10.662457] ata1: SATA link down (SStatus 0 SControl F300)
[   10.668003] ---[ end trace f11ca10700c1adee ]---
[   10.672673] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[   10.672673] 
[   10.681772] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[   10.681772]

Hmm... same exitcode? Hope this is not because of a non specified root-file system ...



Edited 2 time(s). Last edit at 11/02/2016 12:59PM by dietgert.
Re: Synology USB-Station 2 ?
November 02, 2016 03:18PM
dietgert,

That's to be expected. This box does not have NAND flash.

The bright side:

1. You can use the Pogo V4 u-boot to boot the box for recovery purpose.
2. u-boot matches the important aspect of the SoC so it will boot a correct Linux rootfs.
3. We can get it to boot decently, meaning it will work, but probably not all peripherals working.

Need to do:

1. new DTB for the kernel to run this box correctly
2. New u-boot to be able to use the flash, which I'm almost certain is SPI flash. We'll need the GPL source to fully bring up this box. You should look for the GPL source.

How much one can get for this box, e.g. from eBay? if there are more interest from others, I could support this box.

In the mean time, try this to get through the error, see how far the kernel will boot:

- kwboot with Pogo V4 uboot
- Interrupt serial console

setenv mtdparts 
setenv mtdids
setenv partition
boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: Synology USB-Station 2 ?
September 19, 2021 01:09PM
Oops ... 2016 ...
Forgot that device after a relocation for years!
During cleaning up the cellar, now i found this box again.
So... a new try.
Does look quite well now.
Ethernet is missing, but login is possible, shutdown as well.

dietgert

# kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.pogo_v4.mtd0.kwb -p
Sending boot message. Please reboot the target...-
Sending boot image...
  0 % [......................................................................]
               ---->
 99 % [....................................]
[Type Ctrl-\ + c to quit]


U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  0 MiB
MMC:   MVEBU_MMC: 0
*** Warning - readenv() failed, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   egiga0
PHY reset timed out
Hit any key to stop autoboot:  0 
Pogov4> setenv mtdparts 
Pogov4> setenv mtdids
Pogov4> setenv partition
Pogov4> boot
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
       scanning usb for storage devices... 
Use USB retry period from the environment: 15 second(s)

Use USB retry period from the environment: 15 second(s)
2 Storage Device(s) found

Reset IDE: ide_preinit failed
mmc_init: -70, time 41

Partition Map for USB device 0  --   Partition Type: DOS

Part	Start Sector	Num Sectors	UUID		Type
  1	2048      	62535680  	b816adc3-01	83


Partition Map for USB device 1  --   Partition Type: DOS

Part	Start Sector	Num Sectors	UUID		Type
  1	31488     	211712    	0203cdc0-01	83
  2	243200    	7680      	0203cdc0-02	83
  3	16        	31472     	0203cdc0-03	83

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **

no IDE devices available
mmc_init: -70, time 14
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 508 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
5445858 bytes read in 906 ms (5.7 MiB/s)
loading uInitrd ...
9847693 bytes read in 1368 ms (6.9 MiB/s)
loading DTB /boot/dts/kirkwood-pogoplug_v4 ...
** File not found /boot/dts/kirkwood-pogoplug_v4 **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   5.13.6-kirkwood-tld-1
   Created:      2021-09-19  16:50:17 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5445794 Bytes = 5.2 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-5.13.6-kirkwood-tld-1
   Created:      2021-09-19  16:50:46 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9847629 Bytes = 9.4 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
   Loading Ramdisk to 071a5000, end 07b0934d ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000][    T0] Booting Linux on physical CPU 0x0
[    0.000000][    T0] Linux version 5.13.6-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Jul 31 22:10:39 PDT 2021
[    0.000000][    T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000][    T0] CPU: VIVT data cache, VIVT instruction cache
[    0.000000][    T0] OF: fdt: Machine model: Pogoplug v4
[    0.000000][    T0] Memory policy: Data cache writeback
[    0.000000][    T0] Zone ranges:
[    0.000000][    T0]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000][    T0] Movable zone start for each node
[    0.000000][    T0] Early memory node ranges
[    0.000000][    T0]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000][    T0] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000][    T0] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000][    T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10
[    0.000000][    T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000][    T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000][    T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000][    T0] Memory: 100936K/131072K available (11264K kernel code, 1553K rwdata, 4272K rodata, 1024K init, 309K bss, 30136K reserved, 0K cma-reserved)
[    0.000000][    T0] random: get_random_u32 called from ____cache_alloc+0x408/0x7b4 with crng_init=0
[    0.000000][    T0] trace event string verifier disabled
[    0.000000][    T0] rcu: Preemptible hierarchical RCU implementation.
[    0.000000][    T0] 	Trampoline variant of Tasks RCU enabled.
[    0.000000][    T0] 	Tracing variant of Tasks RCU enabled.
[    0.000000][    T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000][    T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000][    T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[    0.000004][    T0] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[    0.000091][    T0] Switching to timer-based delay loop, resolution 6ns
[    0.001406][    T0] Console: colour dummy device 80x30
[    0.001519][    T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[    0.001587][    T0] pid_max: default: 32768 minimum: 301
[    0.002200][    T0] LSM: Security Framework initializing
[    0.002476][    T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.002551][    T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.004779][    T0] CPU: Testing write buffer coherency: ok
[    0.008507][    T1] Setting up static identity map for 0x100000 - 0x100058
[    0.008979][    T1] mvebu-soc-id: MVEBU SoC ID=0x6180, Rev=0x3
[    0.009501][    T1] rcu: Hierarchical SRCU implementation.
[    0.011783][    T1] devtmpfs: initialized
[    0.020183][    T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.020273][    T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.076571][    T1] prandom32: self test passed (less than 6 bits correlated)
[    0.076642][    T1] prandom: seed boundary self test passed
[    0.083011][    T1] prandom: 100 self tests passed
[    0.083056][    T1] pinctrl core: initialized pinctrl subsystem
[    0.085559][    T1] NET: Registered protocol family 16
[    0.086854][    T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.088377][    T1] audit: initializing netlink subsys (disabled)
[    0.090743][    T1] thermal_sys: Registered thermal governor 'step_wise'
[    0.091302][   T16] audit: type=2000 audit(0.080:1): state=initialized audit_enabled=0 res=1
[    0.091567][    T1] cpuidle: using governor ladder
[    0.091716][    T1] cpuidle: using governor menu
[    0.092446][    T1] Feroceon L2: Enabling L2
[    0.092524][    T1] Feroceon L2: Cache support initialised.
[    0.106224][    T1] No ATAGs?
[    2.560100][    C0] random: fast init done
[    7.439316][   T39] "cryptomgr_test" (39) uses obsolete ecb(arc4) skcipher
[    7.478822][   T59] wait_for_initramfs() called before rootfs_initcalls
[    7.680183][    T1] raid6: int32x8  gen()    73 MB/s
[    7.850360][    T1] raid6: int32x8  xor()    46 MB/s
[    8.020363][    T1] raid6: int32x4  gen()    76 MB/s
[    8.190183][    T1] raid6: int32x4  xor()    48 MB/s
[    8.360218][    T1] raid6: int32x2  gen()    99 MB/s
[    8.530134][    T1] raid6: int32x2  xor()    60 MB/s
[    8.700323][    T1] raid6: int32x1  gen()    75 MB/s
[    8.870187][    T1] raid6: int32x1  xor()    43 MB/s
[    8.870212][    T1] raid6: using algorithm int32x2 gen() 99 MB/s
[    8.870233][    T1] raid6: .... xor() 60 MB/s, rmw enabled
[    8.870251][    T1] raid6: using intx1 recovery algorithm
[    8.870641][    T1] vgaarb: loaded
[    8.871498][    T1] SCSI subsystem initialized
[    8.872306][    T1] usbcore: registered new interface driver usbfs
[    8.872414][    T1] usbcore: registered new interface driver hub
[    8.872501][    T1] usbcore: registered new device driver usb
[    8.872813][    T1] pps_core: LinuxPPS API ver. 1 registered
[    8.872837][    T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    8.872890][    T1] PTP clock support registered
[    8.875603][    T1] clocksource: Switched to clocksource orion_clocksource
[    9.026625][    T1] VFS: Disk quotas dquot_6.6.0
[    9.026787][    T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    9.050833][    T1] NET: Registered protocol family 2
[    9.051084][    T1] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    9.052497][    T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    9.052576][    T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    9.052630][    T1] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    9.052673][    T1] TCP: Hash tables configured (established 1024 bind 1024)
[    9.053069][    T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[    9.053181][    T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    9.053246][    T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    9.053593][    T1] NET: Registered protocol family 1
[    9.066227][    T1] RPC: Registered named UNIX socket transport module.
[    9.066263][    T1] RPC: Registered udp transport module.
[    9.066282][    T1] RPC: Registered tcp transport module.
[    9.066300][    T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    9.066327][    T1] PCI: CLS 0 bytes, default 32
[    9.066546][    T1] NetWinder Floating Point Emulator V0.97 (double precision)
[    9.067442][   T58] Trying to unpack rootfs image as initramfs...
[   11.696355][   T58] Freeing initrd memory: 9620K
[   12.622245][    T1] Initialise system trusted keyrings
[   12.622356][    T1] Key type blacklist registered
[   12.622774][    T1] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[   12.622939][    T1] zbud: loaded
[   12.625236][    T1] NFS: Registering the id_resolver key type
[   12.625299][    T1] Key type id_resolver registered
[   12.625321][    T1] Key type id_legacy registered
[   12.625387][    T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[   12.625424][    T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[   12.625447][    T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   12.626002][    T1] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[   12.626851][    T1] fuse: init (API version 7.34)
[   12.627458][    T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[   12.627792][    T1] orangefs_init: module version upstream loaded
[   12.627822][    T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[   12.777587][    T1] xor: measuring software checksum speed
[   12.791007][    T1]    arm4regs        :   742 MB/sec
[   12.813238][    T1]    8regs           :   445 MB/sec
[   12.828544][    T1]    32regs          :   647 MB/sec
[   12.828571][    T1] xor: using function: arm4regs (742 MB/sec)
[   12.828605][    T1] async_tx: api initialized (async)
[   12.828637][    T1] Key type asymmetric registered
[   12.828657][    T1] Asymmetric key parser 'x509' registered
[   12.828751][    T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[   12.828869][    T1] io scheduler bfq registered
[   13.127882][    T1] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47
[   13.127928][    T1] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49
[   13.128507][    T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[   13.131376][    T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[   13.131507][    T1] mvebu-pcie mbus@f1000000:pcie@82000000:      MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[   13.131577][    T1] mvebu-pcie mbus@f1000000:pcie@82000000:      MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[   13.131628][    T1] mvebu-pcie mbus@f1000000:pcie@82000000:       IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[   13.132064][    T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[   13.132100][    T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[   13.132138][    T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[   13.132171][    T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[   13.132200][    T1] pci_bus 0000:00: root bus resource [io  0x1000-0xeffff]
[   13.132387][    T1] pci 0000:00:01.0: [11ab:6180] type 01 class 0x060400
[   13.132445][    T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[   13.134154][    T1] PCI: bus0: Fast back to back transfers disabled
[   13.134210][    T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[   13.135829][    T1] PCI: bus1: Fast back to back transfers enabled
[   13.135878][    T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[   13.136200][    T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref]
[   13.136244][    T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[   13.137173][    T1] mv_xor f1060800.xor: Marvell shared XOR driver
[   13.197299][    T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[   13.201296][    T1] mv_xor f1060900.xor: Marvell shared XOR driver
[   13.267285][    T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[   13.271669][    T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   13.273808][    T1] printk: console [ttyS0] disabled
[   13.273955][    T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A
[   14.264088][    T1] printk: console [ttyS0] enabled
[   14.282253][    T1] loop: module loaded
[   14.287380][    T1] sata_mv f1080000.sata: slots 32 ports 2
[   14.298704][    T1] scsi host0: sata_mv
[   14.303507][    T1] scsi host1: sata_mv
[   14.307837][    T1] ata1: SATA max UDMA/133 irq 32
[   14.312626][    T1] ata2: SATA max UDMA/133 irq 32
[   14.565648][    T1] nand: No NAND device found
[   14.570839][    T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[   14.579438][    T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[   14.591544][    T1] libphy: Fixed MDIO Bus: probed
[   14.598692][    T1] libphy: orion_mdio_bus: probed
[   14.603770][    T1] mdio_bus f1072004.mdio-bus-mii: MDIO device at address 0 is missing.
[   14.612224][    T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   14.620736][    T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   14.628077][    T1] ehci-pci: EHCI PCI platform driver
[   14.633350][    T1] ehci-orion: EHCI orion driver
[   14.638412][    T1] orion-ehci f1050000.ehci: EHCI Host Controller
[   14.644666][    T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[   14.653083][   T94] ata1: SATA link down (SStatus 0 SControl F300)
[   14.659609][    T1] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[   14.695641][    T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[   14.702805][    T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13
[   14.711794][    T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   14.719719][    T1] usb usb1: Product: EHCI Host Controller
[   14.725281][    T1] usb usb1: Manufacturer: Linux 5.13.6-kirkwood-tld-1 ehci_hcd
[   14.732687][    T1] usb usb1: SerialNumber: f1050000.ehci
[   14.739153][    T1] hub 1-0:1.0: USB hub found
[   14.743670][    T1] hub 1-0:1.0: 1 port detected
[   14.749494][    T1] usbcore: registered new interface driver usb-storage
[   14.756828][    T1] mousedev: PS/2 mouse device common for all mice
[   14.764575][    T1] rtc-mv f1010300.rtc: registered as rtc0
[   14.770492][    T1] i2c /dev entries driver
[   14.775958][    T1] device-mapper: uevent: version 1.0.3
[   14.781705][    T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com
[   14.791532][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[   14.798831][    T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[   14.806165][    T1] device-mapper: multipath service-time: version 0.3.0 loaded
[   14.813548][    T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[   14.820354][    T1] device-mapper: raid: Loading target version 1.15.1
[   14.829137][    T1] hid: raw HID events driver (C) Jiri Kosina
[   14.835552][    T1] drop_monitor: Initializing network drop monitor service
[   14.843262][    T1] NET: Registered protocol family 10
[   14.850265][    T1] Segment Routing with IPv6
[   14.854631][    T1] RPL Segment Routing with IPv6
[   14.859613][    T1] NET: Registered protocol family 17
[   14.865062][    T1] Key type dns_resolver registered
[   14.870849][    T1] registered taskstats version 1
[   14.875749][    T1] Loading compiled-in X.509 certificates
[   14.881896][    T1] zswap: loaded using pool lzo/zbud
[   14.887796][    T1] Key type ._fscrypt registered
[   14.892500][    T1] Key type .fscrypt registered
[   14.897252][    T1] Key type fscrypt-provisioning registered
[   14.906608][    T1] Key type big_key registered
[   14.960123][    T1] Key type encrypted registered
[   15.010646][   T96] ata2: SATA link down (SStatus 0 SControl F300)
[   15.031511][    T1] Freeing unused kernel memory: 1024K
[   15.036813][  T102] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   15.045582][    T1] Checked W+X mappings: passed, no W+X pages found
[   15.052023][    T1] Run /init as init process
Loading, please wait...
[   15.257641][  T102] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.60
[   15.275707][  T102] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[   15.283549][  T102] usb 1-1: Product: USB2.0 Hub
Starting version 241
[   15.308275][  T102] hub 1-1:1.0: USB hub found
[   15.335795][  T102] hub 1-1:1.0: 4 ports detected
[   15.655767][  T102] usb 1-1.1: new high-speed USB device number 3 using orion-ehci
[   15.817645][  T102] usb 1-1.1: New USB device found, idVendor=f400, idProduct=f400, bcdDevice= 1.00
[   15.843498][  T102] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   15.871318][  T102] usb 1-1.1: Product: USBstation
[   15.880732][  T102] usb 1-1.1: Manufacturer: Synology
[   15.900434][  T102] usb 1-1.1: SerialNumber: 10091797bb4655
[   15.929239][  T102] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[   15.955943][  T102] scsi host2: usb-storage 1-1.1:1.0
[   16.065728][  T102] usb 1-1.3: new high-speed USB device number 4 using orion-ehci
[   16.243937][  T102] usb 1-1.3: New USB device found, idVendor=05dc, idProduct=c75c, bcdDevice= 1.02
[   16.269292][  T102] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   16.290980][  T102] usb 1-1.3: Product: USB Flash Drive
[   16.311128][  T102] usb 1-1.3: Manufacturer: Lexar
[   16.325873][  T102] usb 1-1.3: SerialNumber: C3EC12EF1D28A4605F3F
[   16.354045][  T102] usb-storage 1-1.3:1.0: USB Mass Storage device detected
[   16.378550][  T102] scsi host3: usb-storage 1-1.3:1.0
[   16.416025][  T134] usbcore: registered new interface driver uas
[   16.487671][  T135] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[   16.753869][   T58] mvsdio f1090000.mvsdio: Got CD GPIO
[   16.967161][    T7] scsi 2:0:0:0: Direct-Access     Synology USBstation       1.0  PQ: 0 ANSI: 2
[   16.985452][   T58] sd 2:0:0:0: [sda] 250880 512-byte logical blocks: (128 MB/123 MiB)
[   17.002210][   T58] sd 2:0:0:0: [sda] Write Protect is off
[   17.013950][   T58] sd 2:0:0:0: [sda] Asking for cache data failed
[   17.025789][   T58] sd 2:0:0:0: [sda] Assuming drive cache: write through
[   17.133337][   T58]  sda: sda1 sda2 sda3
[   17.146446][   T58] sd 2:0:0:0: [sda] Attached SCSI disk
[   17.448396][   T58] scsi 3:0:0:0: Direct-Access     Lexar    USB Flash Drive  8.07 PQ: 0 ANSI: 4
[   17.467586][    T7] sd 3:0:0:0: [sdb] 62537728 512-byte logical blocks: (32.0 GB/29.8 GiB)
[   17.483958][    T7] sd 3:0:0:0: [sdb] Write Protect is off
[   17.497075][    T7] sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   17.521683][    T7]  sdb: sdb1
[   17.536707][    T7] sd 3:0:0:0: [sdb] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[   28.973812][  T159] process '/usr/bin/fstype' started with executable stack
Begin: Will now check root file system ... fsck from util-linux 2.33.1
[/sbin/fsck.ext3 (1) -- /dev/sdb1] fsck.ext3 -a -C0 /dev/sdb1 
rootfs: clean, 18165/1957888 files, 426610/7816960 blocks
done.
[   29.287290][  T169] EXT4-fs (sdb1): mounting ext3 file system using the ext4 subsystem
[   29.421406][  T169] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null). 
Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.93 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Starting hotplug events dispatcher: systemd-udevd.
[....] Synthesizing the initial hotplug events (subsystems)...[   32.365771][    C0] random: crng init done
done.
[ ok ] Synthesizing the initial hotplug events (devices)...done.
[....] Waiting for /dev to be fully populated...[   33.904844][  T378] orion_wdt: Initial timeout 25 sec
[   34.324179][  T394] sd 2:0:0:0: Attached scsi generic sg0 type 0
[   34.441676][  T394] sd 3:0:0:0: Attached scsi generic sg1 type 0
[   34.825525][  T361] marvell-cesa f1030000.crypto: CESA device successfully registered
[   35.088084][  T358] systemd-udevd[358]: link_config: autonegotiation is unset or enabled, 
the speed and duplex are not writable.
done.
[ ok ] Setting hostname to 'debian'...done.
[ ok ] Activating swap:.
[   38.083334][  T572] EXT4-fs (sdb1): re-mounted. Opts: errors=remount-ro. Quota mode: none.
[info] Will now check all file systems.
fsck from util-linux 2.33.1
Checking all file systems.
LABEL=rootfs is mounted
[ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Starting Setting kernel variables: sysctl.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Cannot find device "eth0"
Failed to get interface index: No such device

If you think you have received this message due to a bug rather
than a configuration issue please read the section on submitting
bugs on either our web page at www.isc.org or in the README file
before submitting a bug.  These pages explain the proper
process and the information we find helpful for debugging.

exiting.
ifup: failed to bring up eth0
failed.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1291 (syslogd)
. ok 
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1318 (klogd)
. ok 
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Running local boot scripts (/etc/rc.local).

Debian GNU/Linux 10 debian ttyS0

debian login: 

----------------------------------------------------------------------------------------------

root@debian:~# shutdown -h now

Broadcast message from root@debian (ttyS0) (Wed Dec 31 16:11:28 1969):

The system is going down for system halt NOW!
INIT: Sending processes configured via [info] Using makefile-style concurrent boot in runlevel 0.
[ ok ] Stopping hotplug events dispatcher: systemd-udevd.
[ ok ] Stopping Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[....] Stopping busybox' klogd implementation: klogd1318 (klogd)
Stopped klogd (pid 1318).
. ok 
[....] Stopping busybox' syslogd implementation: syslogd1291 (syslogd)
. ok 
[ ok ] Stopping NFS kernel daemon: mountd nfsd.
[ ok ] Unexporting directories for NFS kernel daemon....
[ ok ] Asking all remaining processes to terminate...done.
[ ok ] All processes ended within 1 seconds...done.
[ ok ] Stopping NFS common utilities: idmapd statd.
[info] Saving the system clock.
hwclock: Warning: unrecognized third line in adjtime file
(Expected: `UTC' or `LOCAL' or nothing.)
hwclock: ioctl(RTC_SET_TIME) to /dev/rtc0 to set the time failed: Numerical result out of range
[ ok ] Stopping RPC port mapper daemon: rpcbind.
[ ok ] Deconfiguring network interfaces...done.
[ ok ] Saving random seed...done.
[....] Will now unmount temporary filesystems:umount: /tmp unmounted
. ok 
[ ok ] Will now deactivate swap:.
[....] Mounting root filesystem read-only...[  707.988296][ T1909] EXT4-fs (sdb1): re-mounted. 
Opts: (null). Quota mode: none.
done.
[info] Will now halt.
logger: socket /dev/log: Connection refused
[  708.295384][ T1932] reboot: System halted

------------------------------------------------------------------------------------------------



Edited 4 time(s). Last edit at 09/19/2021 01:21PM by dietgert.
Re: Synology USB-Station 2 ?
September 19, 2021 04:30PM
dietgert,

> Ethernet is missing, but login is possible,
> shutdown as well.

Do you know which Ethernet chip is on this box? if you don't have that info, you can open the box and look for the chip. Most likely its label starts with 88E, if it is a Marvell chip.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: Synology USB-Station 2 ?
September 19, 2021 11:15PM
The datasheet for the 88F6180 (which I'd never heard of before) is available at DtSheet. WikiDevi doesn't currently list any other devices with that processor.
Re: Synology USB-Station 2 ?
September 20, 2021 01:51PM
bodhi Wrote:
-------------------------------------------------------
> Do you know which Ethernet chip is on this box? if
> you don't have that info, you can open the box and
> look for the chip. Most likely its label starts
> with 88E, if it is a Marvell chip.

Yes, it is.
88E1116R .

The small USB-port on the upperside is not accessible from the outside.
What may be the purpose for this connector ... hmm...

Best Regards,

dietgert
Attachments:
open | download - Network.jpg (446.5 KB)
open | download - Underside.jpg (432.9 KB)
open | download - above.jpg (320.7 KB)
Re: Synology USB-Station 2 ?
September 20, 2021 04:07PM
dietgert,

> Yes, it is. 88E1116R .

If it is 1116 it should work. But I see the error early on here:

Net:   egiga0
PHY reset timed out

Check the Ethernet cable, make sure it is connected well. And kwboot, interrupt countdown, and ping the router

ping <your router IP>

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: Synology USB-Station 2 ?
September 20, 2021 04:20PM
Ah, I see. Looks like this board use a different PHY base address.

Try kwboot with these following 2 u-boots: iConnect and T5325. They won't work well for this box, just might be good enough to start and then ping the router to see if the Ethernet comes up.

https://forum.doozan.com/read.php?3,12381
uboot.2017.07-tld-1.iconnect.bodhi.tar

https://forum.doozan.com/read.php?3,26562
uboot.2017.07-tld-1.t5325.bodhi.tar

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: Synology USB-Station 2 ?
September 21, 2021 02:34PM
bodhi Wrote:
-------------------------------------------------------
> Ah, I see. Looks like this board use a different
> PHY base address.
>
> Try kwboot with these following 2 u-boots:
> iConnect and T5325. They won't work well for this
> box, just might be good enough to start and then
> ping the router to see if the Ethernet comes up.
>
> https://forum.doozan.com/read.php?3,12381
> uboot.2017.07-tld-1.iconnect.bodhi.tar
>
> https://forum.doozan.com/read.php?3,26562
> uboot.2017.07-tld-1.t5325.bodhi.tar


Unfortunately, this didn`t work.
Both create "data trash" after completing kwboot.
With the iconnect uboot the system falls back to boot the synology system at least,
with the T5325 nothing more happened then.

Best Regards,

dietgert
Re: Synology USB-Station 2 ?
September 21, 2021 03:27PM
dietgert,

Connect regular serial console and power up. Interrupt stock u-boot and

help 
mii
See if we can get anything from stock u-boot.

And if you can, find GPL source for this box u-boot at Synology site.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: Synology USB-Station 2 ?
September 23, 2021 01:31PM
Mii command is not available in stock firmware.
Available commands as follows:

Marvell>> help
?       - alias for 'help'
base    - print or set address offset
bootext2    dev:boot_part1,boot_part2 addr boot_image linux_dev_name 
bootm   - boot application image from memory
bootp	- boot image via network using BootP/TFTP protocol
bubt	- Burn an image on the Boot Flash.
cmp     - memory compare
cp      - memory copy
cpumap - Display CPU memory mapping settings.
crc32   - checksum calculation
date    - get/set/reset date & time
diskboot- boot from IDE device
echo    - echo args to console
erase   - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
flinfo  - print FLASH memory information
go      - start application at address 'addr'
help    - print online help
icrc32  - checksum calculation
ide     - IDE sub-system
iloop   - infinite loop on address range
imd     - i2c memory display
imm[.b, .s, .w, .l]     - i2c memory modify (auto-incrementing)
imw     - memory write (fill)
inm     - memory modify (constant address)
iprobe  - probe to discover valid I2C chip addresses
loop    - infinite loop on address range
md      - memory display
mm      - memory modify (auto-incrementing)
mtest   - simple RAM test
mw      - memory write (fill)
nm      - memory modify (constant address)
ping	- send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
resetenv	- Return all environment variable to default.
setenv  - set environment variables
sflash	- read, write or erase the external SPI Flash.
tftpboot- boot image via network using TFTP protocol
usb     - USB sub-system
usbboot - boot from USB device
vendor  - load vendor info
version - print monitor version

BR
dietgert



Edited 2 time(s). Last edit at 09/24/2021 12:39AM by dietgert.
Re: Synology USB-Station 2 ?
September 28, 2021 08:12AM
Sourcecode seems to be on Sourceforge:

https://sourceforge.net/projects/dsgpl/files/Synology%20NAS%20GPL%20Source/1922branch/

1944.pat was not the last Firmware available for this box (1983.pat) however the closest on this site.

BR
dietgert
Re: Synology USB-Station 2 ?
November 12, 2021 03:01PM
Hmm,

during ebay-search for a used kirkwood-box, it came to my mind to boot the USB-Station2 using the DS110j dtb-file ...
Well ...

# kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.pogo_v4.mtd0.kwb -p
Sending boot message. Please reboot the target...\
Sending boot image...
  0 % [......................................................................]
           -->
 99 % [....................................]
[Type Ctrl-\ + c to quit]


U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  0 MiB
MMC:   MVEBU_MMC: 0
*** Warning - readenv() failed, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   egiga0
PHY reset timed out
Hit any key to stop autoboot:  0 
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 4 USB Device(s) found
       scanning usb for storage devices... 
Use USB retry period from the environment: 15 second(s)

Use USB retry period from the environment: 15 second(s)
2 Storage Device(s) found

Reset IDE: ide_preinit failed
mmc_init: -70, time 62

Partition Map for USB device 0  --   Partition Type: DOS

Part	Start Sector	Num Sectors	UUID		Type
  1	31488     	211712    	0203cdc0-01	83
  2	243200    	7680      	0203cdc0-02	83
  3	16        	31472     	0203cdc0-03	83


Partition Map for USB device 1  --   Partition Type: DOS

Part	Start Sector	Num Sectors	UUID		Type
  1	2048      	60086272  	b43cda2c-01	83

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0
loading envs from usb 0 ...
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **

no IDE devices available
mmc_init: -70, time 16
running scan_disk ...
Scan device usb
device usb 0:1
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
device usb 1:1
1 bytes read in 569 ms (0 Bytes/s)
Found bootable drive on usb 1
loading uImage ...
5493996 bytes read in 900 ms (5.8 MiB/s)
loading uInitrd ...
9710222 bytes read in 1228 ms (7.5 MiB/s)
loading DTB /boot/dts/kirkwood-pogoplug_v4 ...
** File not found /boot/dts/kirkwood-pogoplug_v4 **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   5.14.9-kirkwood-tld-1
   Created:      2021-11-12  20:22:14 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5493932 Bytes = 5.2 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-5.14.9-kirkwood-tld-1
   Created:      2021-11-12  20:22:35 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9710158 Bytes = 9.3 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
   Loading Ramdisk to 071c7000, end 07b09a4e ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000][    T0] Booting Linux on physical CPU 0x0
[    0.000000][    T0] Linux version 5.14.9-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Oct 2 17:41:27 PDT 2021
[    0.000000][    T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000][    T0] CPU: VIVT data cache, VIVT instruction cache
[    0.000000][    T0] OF: fdt: Machine model: Synology DS110j v10 and v30
[    0.000000][    T0] Memory policy: Data cache writeback
[    0.000000][    T0] Zone ranges:
[    0.000000][    T0]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000][    T0] Movable zone start for each node
[    0.000000][    T0] Early memory node ranges
[    0.000000][    T0]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000][    T0] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000][    T0] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000][    T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[    0.000000][    T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000][    T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000][    T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000][    T0] Memory: 101020K/131072K available (11264K kernel code, 1568K rwdata, 4308K rodata, 1024K init, 303K bss, 30052K reserved, 0K cma-reserved)
[    0.000000][    T0] random: get_random_u32 called from ____cache_alloc+0x404/0x7b0 with crng_init=0
[    0.000000][    T0] trace event string verifier disabled
[    0.000000][    T0] rcu: Preemptible hierarchical RCU implementation.
[    0.000000][    T0] 	Trampoline variant of Tasks RCU enabled.
[    0.000000][    T0] 	Tracing variant of Tasks RCU enabled.
[    0.000000][    T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000][    T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000][    T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[    0.000003][    T0] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[    0.000086][    T0] Switching to timer-based delay loop, resolution 6ns
[    0.001434][    T0] Console: colour dummy device 80x30
[    0.001547][    T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[    0.001618][    T0] pid_max: default: 32768 minimum: 301
[    0.002235][    T0] LSM: Security Framework initializing
[    0.002515][    T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.002585][    T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.004768][    T0] CPU: Testing write buffer coherency: ok
[    0.008458][    T1] Setting up static identity map for 0x100000 - 0x100058
[    0.008997][    T1] mvebu-soc-id: MVEBU SoC ID=0x6180, Rev=0x3
[    0.009505][    T1] rcu: Hierarchical SRCU implementation.
[    0.011777][    T1] devtmpfs: initialized
[    0.026409][    T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.026501][    T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.082833][    T1] prandom32: self test passed (less than 6 bits correlated)
[    0.082904][    T1] prandom: seed boundary self test passed
[    0.089217][    T1] prandom: 100 self tests passed
[    0.089245][    T1] pinctrl core: initialized pinctrl subsystem
[    0.091786][    T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.093135][    T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.094559][    T1] audit: initializing netlink subsys (disabled)
[    0.096711][    T1] thermal_sys: Registered thermal governor 'step_wise'
[    0.097367][   T16] audit: type=2000 audit(0.090:1): state=initialized audit_enabled=0 res=1
[    0.097652][    T1] cpuidle: using governor ladder
[    0.097801][    T1] cpuidle: using governor menu
[    0.098638][    T1] Feroceon L2: Enabling L2
[    0.098715][    T1] Feroceon L2: Cache support initialised.
[    0.115014][    T1] No ATAGs?
[    2.560094][    C0] random: fast init done
[    7.448684][   T39] "cryptomgr_test" (39) uses obsolete ecb(arc4) skcipher
[    7.700272][    T1] raid6: int32x8  gen()    73 MB/s
[    7.870395][    T1] raid6: int32x8  xor()    46 MB/s
[    8.040352][    T1] raid6: int32x4  gen()    76 MB/s
[    8.210238][    T1] raid6: int32x4  xor()    48 MB/s
[    8.380357][    T1] raid6: int32x2  gen()    97 MB/s
[    8.550171][    T1] raid6: int32x2  xor()    59 MB/s
[    8.720353][    T1] raid6: int32x1  gen()    75 MB/s
[    8.890171][    T1] raid6: int32x1  xor()    43 MB/s
[    8.890199][    T1] raid6: using algorithm int32x2 gen() 97 MB/s
[    8.890220][    T1] raid6: .... xor() 59 MB/s, rmw enabled
[    8.890239][    T1] raid6: using intx1 recovery algorithm
[    8.890635][    T1] vgaarb: loaded
[    8.891501][    T1] SCSI subsystem initialized
[    8.892304][    T1] usbcore: registered new interface driver usbfs
[    8.892411][    T1] usbcore: registered new interface driver hub
[    8.892495][    T1] usbcore: registered new device driver usb
[    8.892834][    T1] pps_core: LinuxPPS API ver. 1 registered
[    8.892858][    T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    8.892910][    T1] PTP clock support registered
[    8.895708][    T1] clocksource: Switched to clocksource orion_clocksource
[    9.032124][    T1] VFS: Disk quotas dquot_6.6.0
[    9.032284][    T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    9.066910][    T1] NET: Registered PF_INET protocol family
[    9.067175][    T1] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    9.068524][    T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    9.068601][    T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    9.068654][    T1] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    9.068697][    T1] TCP: Hash tables configured (established 1024 bind 1024)
[    9.069077][    T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[    9.069201][    T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    9.069259][    T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    9.069614][    T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    9.070790][    T1] RPC: Registered named UNIX socket transport module.
[    9.070824][    T1] RPC: Registered udp transport module.
[    9.070843][    T1] RPC: Registered tcp transport module.
[    9.070860][    T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    9.070887][    T1] PCI: CLS 0 bytes, default 32
[    9.071161][    T1] NetWinder Floating Point Emulator V0.97 (double precision)
[    9.076291][   T75] Trying to unpack rootfs image as initramfs...
[   11.653793][   T75] Freeing initrd memory: 9484K
[   12.666883][    T1] Initialise system trusted keyrings
[   12.666992][    T1] Key type blacklist registered
[   12.667383][    T1] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[   12.667574][    T1] zbud: loaded
[   12.669809][    T1] NFS: Registering the id_resolver key type
[   12.669887][    T1] Key type id_resolver registered
[   12.669909][    T1] Key type id_legacy registered
[   12.669975][    T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[   12.670011][    T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[   12.670035][    T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   12.670449][    T1] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[   12.671232][    T1] fuse: init (API version 7.34)
[   12.671856][    T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[   12.672186][    T1] orangefs_init: module version upstream loaded
[   12.672215][    T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[   12.825371][    T1] xor: measuring software checksum speed
[   12.838934][    T1]    arm4regs        :   735 MB/sec
[   12.861165][    T1]    8regs           :   445 MB/sec
[   12.876476][    T1]    32regs          :   647 MB/sec
[   12.876505][    T1] xor: using function: arm4regs (735 MB/sec)
[   12.876537][    T1] async_tx: api initialized (async)
[   12.876569][    T1] Key type asymmetric registered
[   12.876589][    T1] Asymmetric key parser 'x509' registered
[   12.876684][    T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[   12.876819][    T1] io scheduler bfq registered
[   13.176626][    T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[   13.179604][    T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[   13.179741][    T1] mvebu-pcie mbus@f1000000:pcie@82000000:      MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[   13.179812][    T1] mvebu-pcie mbus@f1000000:pcie@82000000:      MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[   13.179863][    T1] mvebu-pcie mbus@f1000000:pcie@82000000:       IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[   13.180299][    T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[   13.180336][    T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[   13.180374][    T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[   13.180408][    T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[   13.180439][    T1] pci_bus 0000:00: root bus resource [io  0x1000-0xeffff]
[   13.180724][    T1] pci 0000:00:01.0: [11ab:6180] type 01 class 0x060400
[   13.180785][    T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[   13.184151][    T1] PCI: bus0: Fast back to back transfers disabled
[   13.184207][    T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[   13.187505][    T1] PCI: bus1: Fast back to back transfers enabled
[   13.187554][    T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[   13.187879][    T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref]
[   13.187924][    T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[   13.188900][    T1] mv_xor f1060800.xor: Marvell shared XOR driver
[   13.247351][    T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[   13.251171][    T1] mv_xor f1060900.xor: Marvell shared XOR driver
[   13.317343][    T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[   13.321581][    T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   13.323696][    T1] printk: console [ttyS0] disabled
[   13.323845][    T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 27, base_baud = 10416666) is a 16550A
[   14.302868][    T1] printk: console [ttyS0] enabled
[   14.309037][    T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 28, base_baud = 10416666) is a 16550A
[   14.331890][    T1] loop: module loaded
[   14.337189][    T1] sata_mv f1080000.sata: slots 32 ports 2
[   14.348471][    T1] scsi host0: sata_mv
[   14.353326][    T1] scsi host1: sata_mv
[   14.357635][    T1] ata1: SATA max UDMA/133 irq 34
[   14.362432][    T1] ata2: SATA max UDMA/133 irq 34
[   14.369958][    T1] spi-nor spi0.0: found mx25l8005, expected m25p80
[   14.376443][    T1] spi-nor spi0.0: mx25l8005 (1024 Kbytes)
[   14.382109][    T1] 6 fixed-partitions partitions found on MTD device spi0.0
[   14.389181][    T1] Creating 6 MTD partitions on "spi0.0":
[   14.394664][    T1] 0x000000000000-0x000000080000 : "RedBoot"
[   14.402781][    T1] 0x000000080000-0x000000280000 : "zImage"
[   14.408502][    T1] mtd: partition "zImage" extends beyond the end of device "spi0.0" -- size truncated to 0x80000
[   14.421041][    T1] 0x000000280000-0x0000003c0000 : "rd.gz"
[   14.426669][    T1] mtd: partition "rd.gz" is out of reach -- disabled
[   14.435396][    T1] 0x0000003c0000-0x0000003d0000 : "vendor"
[   14.441102][    T1] mtd: partition "vendor" is out of reach -- disabled
[   14.449882][    T1] 0x0000003d0000-0x0000003f0000 : "RedBoot config"
[   14.456284][    T1] mtd: partition "RedBoot config" is out of reach -- disabled
[   14.465871][    T1] 0x0000003f0000-0x000000400000 : "FIS directory"
[   14.472143][    T1] mtd: partition "FIS directory" is out of reach -- disabled
[   14.482156][    T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[   14.490732][    T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[   14.502820][    T1] libphy: Fixed MDIO Bus: probed
[   14.509994][    T1] libphy: orion_mdio_bus: probed
[   14.538996][    T1] mdio_bus f1072004.mdio-bus-mii: MDIO device at address 9 is missing.
[   14.547555][    T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   14.697586][   T94] ata1: SATA link down (SStatus 0 SControl F300)
[   15.037504][   T96] ata2: SATA link down (SStatus 0 SControl F300)
[   15.297242][    T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:xx:xx:xx
[   15.306909][    T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   15.314163][    T1] ehci-pci: EHCI PCI platform driver
[   15.319441][    T1] ehci-orion: EHCI orion driver
[   15.324443][    T1] orion-ehci f1050000.ehci: EHCI Host Controller
[   15.330701][    T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[   15.339333][    T1] orion-ehci f1050000.ehci: irq 32, io mem 0xf1050000
[   15.375761][    T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[   15.382924][    T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.14
[   15.391912][    T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   15.399839][    T1] usb usb1: Product: EHCI Host Controller
[   15.405401][    T1] usb usb1: Manufacturer: Linux 5.14.9-kirkwood-tld-1 ehci_hcd
[   15.412805][    T1] usb usb1: SerialNumber: f1050000.ehci
[   15.419225][    T1] hub 1-0:1.0: USB hub found
[   15.423749][    T1] hub 1-0:1.0: 1 port detected
[   15.429593][    T1] usbcore: registered new interface driver usb-storage
[   15.436992][    T1] mousedev: PS/2 mouse device common for all mice
[   15.443729][    T1] i2c /dev entries driver
[   15.450708][    T1] rtc-s35390a 0-0030: error resetting chip
[   15.457616][    T1] rtc-s35390a: probe of 0-0030 failed with error -5
[   15.465066][    T1] device-mapper: uevent: version 1.0.3
[   15.470929][    T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com
[   15.480719][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[   15.488032][    T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[   15.495328][    T1] device-mapper: multipath service-time: version 0.3.0 loaded
[   15.502745][    T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[   15.509554][    T1] device-mapper: raid: Loading target version 1.15.1
[   15.517376][    T1] kirkwood-pinctrl f1010000.pin-controller: pin PIN21 already requested by f1080000.sata; cannot claim for gpio-leds-hdd-21-1
[   15.530387][    T1] kirkwood-pinctrl f1010000.pin-controller: pin-21 (gpio-leds-hdd-21-1) status -22
[   15.539540][    T1] kirkwood-pinctrl f1010000.pin-controller: could not request pin 21 (PIN21) from group mpp21  on device f1010000.pin-controller
[   15.552657][    T1] leds-gpio gpio-leds-hdd-21-1: Error applying setting, reverse things back
[   15.561401][    T1] hid: raw HID events driver (C) Jiri Kosina
[   15.567936][    T1] drop_monitor: Initializing network drop monitor service
[   15.575564][    T1] NET: Registered PF_INET6 protocol family
[   15.583336][    T1] Segment Routing with IPv6
[   15.587825][    T1] RPL Segment Routing with IPv6
[   15.592657][    T1] NET: Registered PF_PACKET protocol family
[   15.598762][    T1] Key type dns_resolver registered
[   15.604568][    T1] registered taskstats version 1
[   15.609470][    T1] Loading compiled-in X.509 certificates
[   15.615603][    T1] zswap: loaded using pool lzo/zbud
[   15.621254][    T1] Key type ._fscrypt registered
[   15.626155][    T1] Key type .fscrypt registered
[   15.630766][    T1] Key type fscrypt-provisioning registered
[   15.639797][    T1] Key type big_key registered
[   15.689488][    T1] Key type encrypted registered
[   15.703671][    T1] Freeing unused kernel image (initmem) memory: 1024K
[   15.715785][  T105] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   15.727041][    T1] Checked W+X mappings: passed, no W+X pages found
[   15.733455][    T1] Run /init as init process
Loading, please wait...
[   15.917867][  T105] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.60
[   15.935797][  T105] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[   15.943641][  T105] usb 1-1: Product: USB2.0 Hub
Starting version 247.3-6
[   15.967390][  T105] hub 1-1:1.0: USB hub found
[   15.975855][  T105] hub 1-1:1.0: 4 ports detected
[   16.315856][  T105] usb 1-1.1: new high-speed USB device number 3 using orion-ehci
[   16.487734][  T105] usb 1-1.1: New USB device found, idVendor=f400, idProduct=f400, bcdDevice= 1.00
[   16.513057][  T105] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   16.541602][  T105] usb 1-1.1: Product: USBstation
[   16.555982][  T105] usb 1-1.1: Manufacturer: Synology
[   16.561056][  T105] usb 1-1.1: SerialNumber: 10091797bb4655
[   16.587218][  T105] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[   16.616627][  T105] scsi host2: usb-storage 1-1.1:1.0
[   16.725857][  T105] usb 1-1.2: new high-speed USB device number 4 using orion-ehci
[   16.897098][  T105] usb 1-1.2: New USB device found, idVendor=0781, idProduct=5567, bcdDevice= 1.00
[   16.920424][  T105] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   16.945927][  T105] usb 1-1.2: Product: Cruzer Blade
[   16.950910][  T105] usb 1-1.2: Manufacturer: SanDisk
[   16.976859][  T105] usb 1-1.2: SerialNumber: 4C530000250502210301
[   17.001106][  T105] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[   17.030717][  T105] scsi host3: usb-storage 1-1.2:1.0
[   17.156361][  T139] usbcore: registered new interface driver uas
[   17.687253][   T75] scsi 2:0:0:0: Direct-Access     Synology USBstation       1.0  PQ: 0 ANSI: 2
[   17.707534][    T7] sd 2:0:0:0: [sda] 250880 512-byte logical blocks: (128 MB/123 MiB)
[   17.722741][    T7] sd 2:0:0:0: [sda] Write Protect is off
[   17.733299][    T7] sd 2:0:0:0: [sda] Asking for cache data failed
[   17.745967][    T7] sd 2:0:0:0: [sda] Assuming drive cache: write through
[   17.856032][    T7]  sda: sda1 sda2 sda3
[   17.867908][    T7] sd 2:0:0:0: [sda] Attached SCSI disk
[   18.087386][    T7] scsi 3:0:0:0: Direct-Access     SanDisk  Cruzer Blade     1.00 PQ: 0 ANSI: 6
[   18.108163][   T75] sd 3:0:0:0: [sdb] 60088320 512-byte logical blocks: (30.8 GB/28.7 GiB)
[   18.124973][   T75] sd 3:0:0:0: [sdb] Write Protect is off
[   18.136423][   T75] sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   18.170983][   T75]  sdb: sdb1
[   18.187660][   T75] sd 3:0:0:0: [sdb] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.36.1
[/sbin/fsck.ext3 (1) -- /dev/sdb1] fsck.ext3 -a -C0 /dev/sdb1 
rootfs: clean, 18675/1880480 files, 428119/7510784 blocks
done.
[   28.956209][  T172] EXT4-fs (sdb1): mounting ext3 file system using the ext4 subsystem
[   29.082916][  T172] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.96 booting
Using makefile-style concurrent boot in runlevel S.
Setting hostname to 'debian'...done.
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
[   32.863117][    C0] random: crng init done
Waiting for /dev to be fully populated...[   33.015660][  T360] gpio-fan gpio-fan-150-32-35: GPIO fan initialized
[   33.580676][  T360] orion_wdt: Initial timeout 25 sec
[   34.186015][  T354] sd 2:0:0:0: Attached scsi generic sg0 type 0
[   34.237630][  T354] sd 3:0:0:0: Attached scsi generic sg1 type 0
[   34.318246][  T362] marvell-cesa f1030000.crypto: CESA device successfully registered
done.
Activating swap:.
[   36.135552][  T506] EXT4-fs (sdb1): re-mounted. Opts: errors=remount-ro. Quota mode: none.
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
 /tmp.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Starting Setting kernel variables: sysctl.
Initializing random number generator...done.
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/52:3b:20:xx:xx:xx
Sending on   LPF/eth0/52:3b:20:xx:xx:xx
Sending on   Socket/fallback
DHCPREQUEST for 192.168.178.97 on eth0 to 255.255.255.255 port 67
[   43.717577][    C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   43.728183][  T105] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPREQUEST for 192.168.178.97 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.178.97 from 192.168.178.1
invoke-rc.d: could not determine current runlevel
bound to 192.168.178.97 -- renewal in 101910 seconds.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1065 (syslogd)
.
Starting NFS common utilities: statd idmapd.
Starting system message bus: dbus.
Not starting NFS kernel daemon: no exports. ... (warning).
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Starting NTP server: ntpd.
Starting OpenBSD Secure Shell server: sshd.
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1103 (klogd)
.
Running local boot scripts (/etc/rc.local)
.

Debian GNU/Linux 11 debian ttyS0

debian login:

Network is functional. apt-get update/upgrade worked without problems.
I am satisfied for the moment.

Biggest challenge now is to find the correct flash layout.
It is different to the usual kirkwood boxes.

Best Regards,
dietgert


added:
# lsblk
NAME      MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
sda         8:0    0 122.5M  0 disk 
|-sda1      8:1    0 103.4M  0 part 
|-sda2      8:2    0   3.8M  0 part 
`-sda3      8:3    0  15.4M  0 part 
sdb         8:16   1  28.7G  0 disk 
`-sdb1      8:17   1  28.7G  0 part /
mtdblock0  31:0    0   512K  0 disk 
mtdblock1  31:1    0   512K  0 disk



Edited 2 time(s). Last edit at 11/12/2021 03:39PM by dietgert.
Re: Synology USB-Station 2 ?
November 12, 2021 06:28PM
Cool hacking :)

# kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.pogo_v4.mtd0.kwb -p

and then

[    0.000000][    T0] Linux version 5.14.9-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Oct 2 17:41:27 PDT 2021
[    0.000000][    T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000][    T0] CPU: VIVT data cache, VIVT instruction cache
[    0.000000][    T0] OF: fdt: Machine model: Synology DS110j v10 and v30

[   14.547555][    T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   14.697586][   T94] ata1: SATA link down (SStatus 0 SControl F300)
[   15.037504][   T96] ata2: SATA link down (SStatus 0 SControl F300)
[   15.297242][    T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:xx:xx:xx

That was a common Kirkwood Ethernet driver.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 11/12/2021 06:30PM by bodhi.
Re: Synology USB-Station 2 ?
November 12, 2021 06:35PM
Quote

Biggest challenge now is to find the correct flash layout.

I guess without the stock boot log, it is hard to tell. But there is no need.

Since you know you can boot with the Pogo V4 u-boot, we could just wipe the MTDs on SPI flash and flash this u-boot. It looks like a 1MB SPI flash.

[   14.369958][    T1] spi-nor spi0.0: found mx25l8005, expected m25p80
[   14.376443][    T1] spi-nor spi0.0: mx25l8005 (1024 Kbytes)
[   14.382109][    T1] 6 fixed-partitions partitions found on MTD device spi0.0

Want to try that? you got nothing to lose.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: Synology USB-Station 2 ?
November 12, 2021 06:40PM
No, I take it back

Quote

Since you know you can boot with the Pogo V4 u-boot, we could just wipe the MTDs on SPI flash and flash this u-boot. It looks like a 1MB SPI flash.

You cannot flash the Pogo V4 yet. It must be recompiled to boot from SPI.

Or you could try kwboot the HP T5325 or the Dreamplug. These 2 are SPI flash u-boots. If it does not care about RAM, then it will boot.

Quote
https://forum.doozan.com/read.php?3,12381

Last Updated 28 Oct 2017
Updated 06 Dec 2017 (replace Sheevaplug with newer version 2017.07-tld-2)

I've uploaded 2017.07-tld-1 U-Boot images for Pogo E02, GoFlexNet, GoFlex Home, Dockstar, Pogo V4/Mobile, iConnect, Netgear Stora, Sheevaplug, NSA320, NSA325, NSA310S/320S, NSA310, HP-T5325, and Dreamplug.

The HP Thin Client T5325 installation procedure is different from other Kirkwood u-boots, see this thread for installation instruction and download link..

The Marvell Dreamplug box installation procedure is different from other Kirkwood u-boots, see this thread for installation instruction and download link.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: Synology USB-Station 2 ?
November 19, 2021 12:48AM
This didn`t work.
Both create "data trash" after completing kwboot.

BR
dietgert

> bodhi Wrote:
....
>
> Or you could try kwboot the HP T5325 or the
> Dreamplug. These 2 are SPI flash u-boots. If it
> does not care about RAM, then it will boot.
>
Re: Synology USB-Station 2 ?
November 23, 2021 04:34PM
dietgert,

So I guess I need to recompile the Pogo V4 with SPI option (i.e. like a new u-boot for Synology USB-Station-2 u-boot).

Do you want to try that?

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: Synology USB-Station 2 ?
November 29, 2021 02:36AM
Hello Bodhi,

sorry for the delayed answer.

Yes of course. The DSM 3.2 on this Box is ancient.

Best Regards,
dietgert

bodhi Wrote:
-------------------------------------------------------
> dietgert,
>
> So I guess I need to recompile the Pogo V4 with
> SPI option (i.e. like a new u-boot for Synology
> USB-Station-2 u-boot).
>
> Do you want to try that?
Re: Synology USB-Station 2 ?
November 29, 2021 05:11PM
dietgert,

It might take a while. So in the mean time just run it with kwboot.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: