PogoPlug Mobile - Stuck at "booting the kernel." September 22, 2017 01:49AM |
Registered: 6 years ago Posts: 44 |
EHCI timed out on TD - token=0x1e008d80
** ext4fs_devread read error - block
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 22, 2017 02:11AM |
Admin Registered: 13 years ago Posts: 18,570 |
printenv boot
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 22, 2017 02:14AM |
Admin Registered: 13 years ago Posts: 18,570 |
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 22, 2017 02:21AM |
Registered: 6 years ago Posts: 44 |
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 22, 2017 02:29AM |
Admin Registered: 13 years ago Posts: 18,570 |
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
Quote
4. Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Skip this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time).
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 22, 2017 02:38AM |
Registered: 6 years ago Posts: 44 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> printenv arcNumber=3960 baudrate=115200 bootcmd=run bootcmd_mmc; run bootcmd_usb; run bootcmd_sata; run bootcmd_pogo; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_pogo=if ubi part root 2048 && ubifsmount ubi:rootfs && ubifsload 0x800000 uboot.mtd0.dockstar.original.kwb ; then go 0x800200; fi bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 ethaddr=00:25:31:05:a7:5b if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking machid=F78 mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 serverip=192.168.0.220 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 usb_rootfstype=ext3 Environment size: 2415/131068 bytes Pogov4> boot ** Bad device mmc 0 ** ** Bad device mmc 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found 3831876 bytes read in 482 ms (7.6 MiB/s) 7245696 bytes read in 621 ms (11.1 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-09-22 6:30:03 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3831812 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Using machid 0xf78 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel.
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> printenv arcNumber=3960 baudrate=115200 bootcmd=run bootcmd_mmc; run bootcmd_usb; run bootcmd_sata; run bootcmd_pogo; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_pogo=if ubi part root 2048 && ubifsmount ubi:rootfs && ubifsload 0x800000 uboot.mtd0.dockstar.original.kwb ; then go 0x800200; fi bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 ethaddr=00:25:31:05:a7:5b if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking machid=F78 mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 serverip=192.168.0.220 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 usb_rootfstype=ext3 Environment size: 2415/131068 bytes Pogov4> boot ** Bad device mmc 0 ** ** Bad device mmc 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found 3821592 bytes read in 482 ms (7.6 MiB/s) EHCI timed out on TD - token=0x30008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x1f8c80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x1f8c80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x1f8c80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x1f8c80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x1f8c80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 ** ext4fs_devread read error - block ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-07-20 8:11:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3821528 Bytes = 3.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK Using machid 0xf78 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: unrecognized/unsupported machine ID (r1 = 0x00000f78). Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Kirkwood (Flattened Device Tree) Please check your kernel config and/or bootloader.
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 22, 2017 02:59AM |
Admin Registered: 13 years ago Posts: 18,570 |
Quote
8. Flashing default u-boot envs image:
As described in step 1, u-boot envs must be defined in etc/fw_env.config as
# MTD device name Device offset Env. size Flash sector size Number of sectors
/dev/mtd0 0xc0000 0x20000 0x20000
A special section (B. Flashing default u-boot envs image) about flashing default u-boot envs is included at the end of this installation procedure. Please follow the instruction in this section B to perform this step before continuing with step 9.
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 22, 2017 03:21AM |
Admin Registered: 13 years ago Posts: 18,570 |
setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' setenv usb_load_dtb 'ext2load usb $device 0x1c00000 /boot/dts/kirkwood-pogoplug_v4.dtb' setenv usb_boot 'mw 0x800000 0 1; run usb_load_uimage; run usb_load_uinitrd; run usb_load_dtb; bootm 0x800000 0x1100000 0x1c00000' printenv boot
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 22, 2017 05:11PM |
Admin Registered: 13 years ago Posts: 18,570 |
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 22, 2017 10:37PM |
Registered: 6 years ago Posts: 44 |
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 23, 2017 12:00AM |
Admin Registered: 13 years ago Posts: 18,570 |
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 23, 2017 03:35AM |
Registered: 6 years ago Posts: 44 |
/boot/zImage /boot/uInitrd /boot/dtbs/kirkwood-pogoplug-series-4.dtb
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 23, 2017 03:57AM |
Admin Registered: 13 years ago Posts: 18,570 |
> /boot/zImage > /boot/uInitrd > /boot/dtbs/kirkwood-pogoplug-series-4.dtb >
setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' setenv usb_load_dtb 'ext2load usb $device 0x1c00000 /boot/dts/kirkwood-pogoplug_v4.dtb' setenv usb_boot 'mw 0x800000 0 1; run usb_load_uimage; run usb_load_uinitrd; run usb_load_dtb; bootm 0x800000 0x1100000 0x1c00000' printenv boot
setenv bootargs_usb 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' setenv usb_load_image 'ext2load usb $device 0x800000 /boot/zImage' setenv usb_load_dtb 'ext2load usb $device 0x1c00000 /boot/dtbs/kirkwood-pogoplug-series-4.dtb setenv usb_boot 'mw 0x800000 0 1; run usb_load_image; run usb_load_uinitrd; run usb_load_dtb; bootz 0x800000 0x1100000 0x1c00000' boot
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 23, 2017 03:17PM |
Registered: 6 years ago Posts: 44 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> printenv arcNumber=3960 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_add r - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethact=egiga0 ethaddr=00:25:31:05:a7:5b if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=f78 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; fo r disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uima ge_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; vers ion; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtyp e in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read _disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then se tenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknu m; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 2877/131068 bytes Pogov4>
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 23, 2017 05:01PM |
Admin Registered: 13 years ago Posts: 18,570 |
setenv dtb_file '/boot/dtbs/kirkwood-pogoplug-series-4.dtb' setenv load_image 'echo loading Image ...; load $bootdev $device $load_image_addr /boot/zImage setenv bootcmd_exec 'run load_image; if run load_initrd; then if run load_dtb; then bootz $load_image_addr $load_initrd_addr $load_dtb_addr; else bootz $load_image_addr $load_initrd_addr; fi; else if run load_dtb; then bootz $load_image_addr - $load_dtb_addr; else bootz $load_image_addr; fi; fi' boot
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 23, 2017 07:52PM |
Registered: 6 years ago Posts: 44 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> setenv dtb_file '/boot/dtbs/kirkwood-pogoplug-series-4.dtb' Pogov4> setenv load_image 'echo loading Image ...; load $bootdev $device $load_image_addr /boot/zImage' Pogov4> setenv bootcmd_exec 'run load_image; if run load_initrd; then if run load_dtb; then bootz $load_image_addr $lo ad_initrd_addr $load_dtb_addr; else bootz $load_image_addr $load_initrd_addr; fi; else if run load_dtb; then bootz $lo ad_image_addr - $load_dtb_addr; else bootz $load_image_addr; fi; fi' Pogov4> printenv arcNumber=3960 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_image; if run load_initrd; then if run load_dtb; then bootz $load_image_addr $load_initrd_addr $ load_dtb_addr; else bootz $load_image_addr $load_initrd_addr; fi; else if run load_dtb; then bootz $load_image_addr - $load_dtb_addr; else bootz $load_image_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dtbs/kirkwood-pogoplug-series-4.dtb ethact=egiga0 ethaddr=00:25:31:05:a7:5b if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_image=echo loading Image ...; load $bootdev $device $load_image_addr /boot/zImage load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=f78 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; fo r disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uima ge_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; vers ion; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtyp e in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read _disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then se tenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknu m; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 2968/131068 bytes Pogov4> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: ide_preinit failed Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 15656960 4efd6d24-01 83 Boot loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** no IDE devices available running scan_disk ... Scan device usb device usb 0:1 ** File not found /boot/uImage ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Reset IDE: ide_preinit failed device ide 0:1 ** Bad device size - ide 0 ** device ide 1:1 ** Bad device size - ide 1 ** device ide 2:1 ** Bad device ide 2 ** device ide 3:1 ** Bad device ide 3 ** Scan device mmc device mmc 0:1 ** Bad device mmc 0 ** device mmc 1:1 MMC Device 1 not found MMC Device 1 not found ** Bad device mmc 1 ** device mmc 2:1 MMC Device 2 not found MMC Device 2 not found ** Bad device mmc 2 ** device mmc 3:1 MMC Device 3 not found MMC Device 3 not found ** Bad device mmc 3 ** loading Image ... load - load binary file from a filesystem Usage: load <interface> [<dev[:part]> [<addr> [<filename> [bytes [pos]]]]] - Load binary file 'filename' from partition 'part' on device type 'interface' instance 'dev' to address 'addr' in memory. 'bytes' gives the size to load in bytes. If 'bytes' is 0 or omitted, the file is read until the end. 'pos' gives the file byte position to start reading from. If 'pos' is 0 or omitted, the file is read from the start. loading uInitrd ... 44126192 bytes read in 1740 ms (24.2 MiB/s) loading DTB /boot/dtbs/kirkwood-pogoplug-series-4.dtb ... 10694 bytes read in 4429 ms (2 KiB/s) Bad Linux ARM zImage magic! Pogov4>
Pogov4> load usb 0 0x800000 /boot/zImage 7589664 bytes read in 606 ms (11.9 MiB/s) Pogov4> load usb 0 0x1100000 /boot/uInitrd 44126192 bytes read in 1743 ms (24.1 MiB/s) Pogov4> load usb 0 0x1c00000 /boot/dtbs/kirkwood-pogoplug-series-4.dtb 10694 bytes read in 4429 ms (2 KiB/s) Pogov4> bootz 0x800000 0x1100000 0x1c00000 Kernel image @ 0x800000 [ 0x000000 - 0x73cf20 ] ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: Void Linux Created: 2017-09-23 23:58:05 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 44126128 Bytes = 42.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... Bad Data CRC Ramdisk image is corrupt or invalid Pogov4>
env -i /usr/bin/mkimage -A arm -O linux -T ramdisk -C none -a 0 -e 0 -n 'Void Linux' -d /boot/initrd /boot/uInitrd
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 24, 2017 01:35AM |
Admin Registered: 13 years ago Posts: 18,570 |
setenv load_image_addr 0x800000 setenv scan_disk 'echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_image_addr /boot/zImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done' setenv dtb_file '/boot/dtbs/kirkwood-pogoplug-series-4.dtb' setenv load_image 'echo loading Image ...; load $bootdev $device $load_image_addr /boot/zImage setenv bootcmd_exec 'run load_image; if run load_initrd; then if run load_dtb; then bootz $load_image_addr $load_initrd_addr $load_dtb_addr; else bootz $load_image_addr $load_initrd_addr; fi; else if run load_dtb; then bootz $load_image_addr - $load_dtb_addr; else bootz $load_image_addr; fi; fi' boot
## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: Void Linux Created: 2017-09-23 23:58:05 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 44126128 Bytes = 42.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... Bad Data CRC
cd /boot mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-4.13.2-kirkwood-tld-1 -d initrd.img-4.13.2-kirkwood-tld-1 uInitrd
env -i /usr/bin/mkimage -A arm -O linux -T ramdisk -C none -a 0 -e 0 -n 'Void Linux' -d /boot/initrd /boot/uInitrd
-rw-r--r-- 1 root root 6.8M Sep 23 03:11 /boot/initrd.img-4.13.2-kirkwood-tld-1
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 24, 2017 02:18AM |
Registered: 6 years ago Posts: 44 |
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 24, 2017 02:43AM |
Admin Registered: 13 years ago Posts: 18,570 |
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 24, 2017 02:54AM |
Registered: 6 years ago Posts: 44 |
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 24, 2017 03:37AM |
Admin Registered: 13 years ago Posts: 18,570 |
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 24, 2017 03:45AM |
Admin Registered: 13 years ago Posts: 18,570 |
Quote
Data Size: 44126128 Bytes = 42.1 MiB
setenv load_dtb_addr 0x3000000
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 25, 2017 12:32AM |
Registered: 6 years ago Posts: 44 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> setenv load_image_addr 0x800000 Pogov4> setenv scan_disk 'echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_image_addr /boot/zImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknu m:1; setenv bootdev $dev; fi; fi; done; fi; done' Pogov4> setenv dtb_file '/boot/dtbs/kirkwood-pogoplug-series-4.dtb' Pogov4> setenv load_image 'echo loading Image ...; load $bootdev $device $load_image_addr /boot/zImage' Pogov4> setenv bootcmd_exec 'run load_image; if run load_initrd; then if run load_dtb; then bootz $load_image_addr $load_initrd_addr $load_dtb_addr; else bootz $load_image_addr $load_initrd_addr; fi; else if run load_dtb; then bootz $load _image_addr - $load_dtb_addr; else bootz $load_image_addr; fi; fi' Pogov4> setenv load_dtb_addr 0x3000000 Pogov4> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: ide_preinit failed Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 15656960 4efd6d24-01 83 Boot loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** no IDE devices available running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 317 ms (0 Bytes/s) Found bootable drive on usb 0 loading Image ... 7589664 bytes read in 608 ms (11.9 MiB/s) loading uInitrd ... 44126192 bytes read in 1758 ms (23.9 MiB/s) loading DTB /boot/dtbs/kirkwood-pogoplug-series-4.dtb ... 10694 bytes read in 4429 ms (2 KiB/s) Kernel image @ 0x800000 [ 0x000000 - 0x73cf20 ] ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: Void Linux Created: 2017-09-23 23:58:05 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 44126128 Bytes = 42.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... Bad Data CRC Ramdisk image is corrupt or invalid Pogov4> printenv arcNumber=3960 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_image; if run load_initrd; then if run load_dtb; then bootz $load_image_addr $load_initrd_addr $load_dtb_addr; else bootz $load_image_addr $load_initrd_addr; fi; else if run load_dtb; then bootz $load_image_addr - $l oad_dtb_addr; else bootz $load_image_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dtbs/kirkwood-pogoplug-series-4.dtb ethact=egiga0 ethaddr=00:25:31:05:a7:5b fileaddr=3000000 filesize=29c6 if_netconsole=ping $serverip init_ide=ide reset init_mmc=mmc rescan init_usb=usb start ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x3000000 load_image=echo loading Image ...; load $bootdev $device $load_image_addr /boot/zImage load_image_addr=0x800000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=f78 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_image_addr /boot/zImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv boot dev $dev; fi; fi; done; fi; done scan_ide=ide reset scan_mmc=mmc rescan scan_usb=usb start serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_loaded=0 uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 3314/131068 bytes Pogov4>
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 25, 2017 01:17AM |
Admin Registered: 13 years ago Posts: 18,570 |
setenv load_dtb_addr 0x600000
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 25, 2017 01:42AM |
Registered: 6 years ago Posts: 44 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> printenv arcNumber=3960 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_add r - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethact=egiga0 ethaddr=00:25:31:05:a7:5b if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=f78 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; fo r disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uima ge_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; vers ion; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtyp e in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read _disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then se tenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknu m; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 2877/131068 bytes Pogov4> setenv load_dtb_addr 0x600000 Pogov4> setenv load_image_addr 0x800000 Pogov4> setenv scan_disk 'echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; r un scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disk num:1 $load_image_addr /boot/zImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $di sknum:1; setenv bootdev $dev; fi; fi; done; fi; done' Pogov4> setenv dtb_file '/boot/dtbs/kirkwood-pogoplug-series-4.dtb' Pogov4> setenv bootcmd_exec 'run load_image; if run load_initrd; then if run load_dtb; then bootz $load_image_addr $lo ad_initrd_addr $load_dtb_addr; else bootz $load_image_addr $load_initrd_addr; fi; else if run load_dtb; then bootz $lo ad_image_addr - $load_dtb_addr; else bootz $load_image_addr; fi; fi' Pogov4> setenv load_image 'echo loading Image ...; load $bootdev $device $load_image_addr /boot/zImage' Pogov4> setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial $m tdparts $custom_params' Pogov4> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: ide_preinit failed Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 15656960 4efd6d24-01 83 Boot loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** no IDE devices available running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 317 ms (0 Bytes/s) Found bootable drive on usb 0 loading Image ... 7589664 bytes read in 608 ms (11.9 MiB/s) loading uInitrd ... 44126192 bytes read in 1758 ms (23.9 MiB/s) loading DTB /boot/dtbs/kirkwood-pogoplug-series-4.dtb ... 10694 bytes read in 4429 ms (2 KiB/s) Kernel image @ 0x800000 [ 0x000000 - 0x73cf20 ] ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: Void Linux Created: 2017-09-23 23:58:05 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 44126128 Bytes = 42.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 00600000 Booting using the fdt blob at 0x600000 Loading Ramdisk to 050f9000, end 07b0dfb0 ... OK Loading Device Tree to 050f3000, end 050f89c5 ... OK Using machid 0xf78 from environment Starting kernel ...
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 25, 2017 03:10AM |
Admin Registered: 13 years ago Posts: 18,570 |
Starting kernel ...
7589664 bytes read in 608 ms (11.9 MiB/s)
setenv load_initrd_add 0x2100000
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 26, 2017 12:57AM |
Registered: 6 years ago Posts: 44 |
[ 12.319973] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:a7:5b [ 12.328852] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.335437] ehci-pci: EHCI PCI platform driver [ 12.339957] ehci-orion: EHCI orion driver [ 12.344276] orion-ehci f1050000.ehci: EHCI Host Controller [ 12.349780] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 12.357682] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 12.392732] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 12.399044] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 12.405848] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.413065] usb usb1: Product: EHCI Host Controller [ 12.417930] usb usb1: Manufacturer: Linux 4.13.3_1 ehci_hcd [ 12.423509] usb usb1: SerialNumber: f1050000.ehci [ 12.429141] hub 1-0:1.0: USB hub found [ 12.433012] hub 1-0:1.0: 1 port detected [ 12.437823] usbcore: registered new interface driver usb-storage [ 12.444382] mousedev: PS/2 mouse device common for all mice [ 12.792735] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 12.990312] usb 1-1: New USB device found, idVendor=05dc, idProduct=c75c [ 12.997032] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 13.004192] usb 1-1: Product: USB Flash Drive [ 13.008534] usb 1-1: Manufacturer: Lexar [ 13.012448] usb 1-1: SerialNumber: 55B6FA74BBD32312E06D [ 13.018737] usb-storage 1-1:1.0: USB Mass Storage device detected [ 13.025336] scsi host1: usb-storage 1-1:1.0 [ 13.522726] rtc-mv f1010300.rtc: internal RTC not ticking [ 13.528354] i2c /dev entries driver [ 13.533899] hidraw: raw HID events driver (C) Jiri Kosina [ 13.539838] drop_monitor: Initializing network drop monitor service [ 13.546553] NET: Registered protocol family 17 [ 13.551096] Key type dns_resolver registered [ 13.556573] registered taskstats version 1 [ 13.560653] Loading compiled-in X.509 certificates [ 13.565549] zswap: loaded using pool lzo/zbud [ 13.588342] Key type big_key registered [ 13.609760] Key type encrypted registered [ 13.615881] hctosys: unable to open rtc device (rtc0) [ 13.625971] Freeing unused kernel memory: 1024K [ 14.085215] scsi 1:0:0:0: Direct-Access Lexar USB Flash Drive 8.07 PQ: 0 ANSI: 4 [ 14.105630] sd 1:0:0:0: [sda] 15659008 512-byte logical blocks: (8.02 GB/7.47 GiB) [ 14.124916] sd 1:0:0:0: [sda] Write Protect is off [ 14.142518] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 14.183356] sda: sda1 [ 14.195018] sd 1:0:0:0: [sda] Attached SCSI removable disk [ 14.367683] dracut: dracut-046 [ 14.906234] systemd-udevd[183]: starting version 3.2.4 [ 14.934203] udevd[184]: starting eudev-3.2.4 [ 15.406631] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 15.530029] usbcore: registered new interface driver uas [ 15.693673] mvsdio f1090000.mvsdio: Got CD GPIO [ 15.731876] mvsdio f1090000.mvsdio: Got WP GPIO [ 16.224929] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 16.243502] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 16.543582] dracut: Checking ext3: /dev/disk/by-label/rootfs [ 16.551678] dracut: issuing e2fsck -a /dev/disk/by-label/rootfs [ 16.640153] dracut: rootfs: clean, 9946/489600 files, 116303/1957120 blocks [ 16.686701] dracut: Mounting /dev/disk/by-label/rootfs with -o defaults [ 16.737314] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 16.758265] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 16.896206] dracut: Mounted root filesystem /dev/sda1 [ 17.396652] dracut: Switching root - runit: $Id: 25da3b86f7bed4038b8a039d2f8e8c9bbcf0822b $: booting. - runit: enter stage: /etc/runit/1 => Welcome to Void! => Mounting pseudo-filesystems... [ 18.392809] raid6: int32x1 gen() 63 MB/s [ 18.563194] raid6: int32x1 xor() 42 MB/s [ 18.732831] raid6: int32x2 gen() 78 MB/s [ 18.903190] raid6: int32x2 xor() 60 MB/s [ 19.073027] raid6: int32x4 gen() 81 MB/s [ 19.243258] raid6: int32x4 xor() 55 MB/s [ 19.413161] raid6: int32x8 gen() 84 MB/s [ 19.583077] raid6: int32x8 xor() 57 MB/s [ 19.587330] raid6: using algorithm int32x8 gen() 84 MB/s [ 19.592616] raid6: .... xor() 57 MB/s, rmw enabled [ 19.597415] raid6: using intx1 recovery algorithm [ 19.605292] xor: measuring software checksum speed [ 19.702758] arm4regs : 726.000 MB/sec [ 19.802772] 8regs : 436.000 MB/sec [ 19.902707] 32regs : 634.000 MB/sec [ 19.906881] xor: using function: arm4regs (726.000 MB/sec) [ 20.065223] Btrfs loaded, crc32c=crc32c-generic [ 20.096950] tun: Universal TUN/TAP device driver, 1.6 [ 20.130334] PPP generic driver version 2.4.2 [ 20.197592] device-mapper: uevent: version 1.0.3 [ 20.202607] device-mapper: ioctl: 4.36.0-ioctl (2017-06-09) initialised: dm-devel@redhat.com [ 20.419442] Bluetooth: Core ver 2.22 [ 20.423230] NET: Registered protocol family 31 [ 20.427655] Bluetooth: HCI device and connection manager initialized [ 20.434033] Bluetooth: HCI socket layer initialized [ 20.438905] Bluetooth: L2CAP socket layer initialized [ 20.444005] Bluetooth: SCO socket layer initialized => Loading kernel modules... => Starting udev and waiting for devices to settle... [ 20.691083] udevd[357]: starting version 3.2.4 [ 20.769017] udevd[358]: starting eudev-3.2.4 [ 21.578690] marvell-cesa f1030000.crypto: CESA device successfully registered [ 21.617180] orion_wdt: Initial timeout 25 sec => Remounting rootfs read-only... [ 23.158797] random: crng init done [ 30.559392] EXT4-fs (sda1): re-mounted. Opts: data=ordered => Activating btrfs devices... Scanning for Btrfs filesystems => Activating encrypted devices... => Checking filesystems: => Mounting rootfs read-write... [ 31.302345] EXT4-fs (sda1): re-mounted. Opts: data=ordered => Mounting all non-network filesystems... => Initializing swap... => Initializing random seed... => Setting up loopback interface... => Setting up hostname to 'void-live'... => Loading sysctl(8) settings... * Applying /usr/lib/sysctl.d/void.conf ... kernel.core_uses_pid = 1 fs.protected_hardlinks = 1 fs.protected_symlinks = 1 kernel.kptr_restrict = 1 kernel.dmesg_restrict = 1 kernel.perf_event_paranoid = 2 kernel.kexec_load_disabled = 1 sysctl: cannot stat /proc/sys/kernel/yama/ptrace_scope: No such file or directory * Applying /etc/sysctl.conf ... => Initialization complete, running stage 2... - runit: leave stage: /etc/runit/1 - runit: enter stage: /etc/runit/2 runsvchdir: default: current. [ 32.794247] udevd[420]: starting version 3.2.4 [ 32.845833] udevd[420]: starting eudev-3.2.4 Void 4.13.3_1 (void-live) (console) void-live login: r[ 37.062997] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow contro l disabled oot Password: Last login: Thu Jan 1 00:00:40 on console # [ 41.212161] NET: Registered protocol family 10 [ 41.219135] Segment Routing with IPv6 # pstree runit---runsvdir-+-runsv---sshd |-runsv---login---sh---pstree |-runsv---udevd---udevd `-runsv---dhcpcd # uname -a Linux void-live 4.13.3_1 #1 PREEMPT Mon Sep 25 05:39:14 UTC 2017 armv5tel GNU/Linux # free -m total used free shared buff/cache available Mem: 114 12 74 0 28 97 Swap: 0 0 0 # df -h Filesystem Size Used Avail Use% Mounted on devtmpfs 52M 0 52M 0% /dev tmpfs 58M 0 58M 0% /dev/shm tmpfs 58M 144K 58M 1% /run /dev/sda1 7.3G 271M 6.7G 4% / cgroup 58M 0 58M 0% /sys/fs/cgroup tmpfs 58M 0 58M 0% /tmp #
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 26, 2017 02:46AM |
Admin Registered: 13 years ago Posts: 18,570 |
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 28, 2017 01:57AM |
Registered: 6 years ago Posts: 44 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 Pogov4> printenv arcNumber=3960 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_add r - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethact=egiga0 ethaddr=00:25:31:05:a7:5b if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=f78 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; fo r disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uima ge_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; vers ion; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtyp e in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read _disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then se tenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknu m; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 2877/131068 bytes Pogov4> setenv load_image_addr 0x800000 Pogov4> setenv scan_disk 'echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; r un scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disk num:1 $load_image_addr /boot/zImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $di sknum:1; setenv bootdev $dev; fi; fi; done; fi; done' Pogov4> setenv dtb_file '/boot/dtbs/kirkwood-pogoplug-series-4.dtb' Pogov4> setenv load_image 'echo loading Image ...; load $bootdev $device $load_image_addr /boot/zImage' Pogov4> setenv bootcmd_exec 'run load_image; if run load_initrd; then if run load_dtb; then bootz $load_image_addr $lo ad_initrd_addr $load_dtb_addr; else bootz $load_image_addr $load_initrd_addr; fi; else if run load_dtb; then bootz $lo ad_image_addr - $load_dtb_addr; else bootz $load_image_addr; fi; fi' Pogov4> setenv load_dtb_addr 0x3000000 Pogov4> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: ide_preinit failed Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 15728640 6f963f29-01 83 Boot loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** no IDE devices available running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 317 ms (0 Bytes/s) Found bootable drive on usb 0 loading Image ... 3839416 bytes read in 548 ms (6.7 MiB/s) loading uInitrd ... 11926531 bytes read in 940 ms (12.1 MiB/s) loading DTB /boot/dtbs/kirkwood-pogoplug-series-4.dtb ... 10694 bytes read in 935 ms (10.7 KiB/s) Kernel image @ 0x800000 [ 0x000000 - 0x3a95b8 ] ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: Void Linux Created: 2017-09-28 6:21:12 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 11926467 Bytes = 11.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 03000000 Booting using the fdt blob at 0x3000000 Loading Ramdisk to 06fae000, end 07b0dbc3 ... OK Loading Device Tree to 06fa8000, end 06fad9c5 ... OK Using machid 0xf78 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.13.3_1 (maldridge@darkstar) (gcc version 6.3.0 (GCC)) #1 PREEMPT Tue Sep 26 06:20:29 UT C 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: Cloud Engines PogoPlug Series 4 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:2M(u-boot) ,3M(uImage),3M(uImage2),8M(failsafe),112M(root) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 104860K/131072K available (8192K kernel code, 712K rwdata, 2008K rodata, 1024K init, 284K bss, 26212K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db228c ( 713 kB) [ 0.000000] .bss : 0xc0db8cec - 0xc0dffd0c ( 285 kB) [ 0.000000] random: get_random_u32 called from cache_alloc_refill+0x378/0x8dc with crng_init=0 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000014] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000067] Switching to timer-based delay loop, resolution 6ns [ 0.000771] Console: colour dummy device 80x30 [ 0.000825] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666 ) [ 0.000859] pid_max: default: 32768 minimum: 301 [ 0.001149] Security Framework initialized [ 0.001363] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001400] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002717] CPU: Testing write buffer coherency: ok [ 0.004252] Setting up static identity map for 0x100000 - 0x100058 [ 0.004660] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.005038] Hierarchical SRCU implementation. [ 0.010036] devtmpfs: initialized [ 0.015716] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.015756] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.016357] prandom: seed boundary self test passed [ 0.022757] prandom: 100 self tests passed [ 0.022785] pinctrl core: initialized pinctrl subsystem [ 0.024412] NET: Registered protocol family 16 [ 0.025161] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.027334] cpuidle: using governor ladder [ 0.027437] cpuidle: using governor menu [ 0.028154] Feroceon L2: Enabling L2 [ 0.028217] Feroceon L2: Cache support initialised. [ 0.028733] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.035719] No ATAGs? [ 0.049514] vgaarb: loaded [ 0.049993] SCSI subsystem initialized [ 0.050745] usbcore: registered new interface driver usbfs [ 0.050856] usbcore: registered new interface driver hub [ 0.050971] usbcore: registered new device driver usb [ 0.052631] clocksource: Switched to clocksource orion_clocksource [ 0.187263] VFS: Disk quotas dquot_6.6.0 [ 0.187385] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.202127] NET: Registered protocol family 2 [ 0.203277] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.203316] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.203346] TCP: Hash tables configured (established 1024 bind 1024) [ 0.203472] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.203508] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.203766] NET: Registered protocol family 1 [ 0.204367] RPC: Registered named UNIX socket transport module. [ 0.204385] RPC: Registered udp transport module. [ 0.204396] RPC: Registered tcp transport module. [ 0.204407] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.204761] Unpacking initramfs... [ 1.211169] Freeing initrd memory: 11648K [ 1.211399] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.212809] audit: initializing netlink subsys (disabled) [ 1.213542] Initialise system trusted keyrings [ 1.213636] Key type blacklist registered [ 1.213771] audit: type=2000 audit(1.210:1): state=initialized audit_enabled=0 res=1 [ 1.213892] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 1.213993] zbud: loaded [ 1.215282] NFS: Registering the id_resolver key type [ 1.215321] Key type id_resolver registered [ 1.215334] Key type id_legacy registered [ 1.215359] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.215374] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.215684] jffs2: version 2.2. (NAND) (SUMMARY) � 2001-2006 Red Hat, Inc. [ 1.215972] fuse init (API version 7.26) [ 1.216530] orangefs_debugfs_init: called with debug mask: :none: :0: [ 1.216929] orangefs_init: module version upstream loaded [ 1.216944] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.552642] random: fast init done [ 10.106961] Key type asymmetric registered [ 10.106984] Asymmetric key parser 'x509' registered [ 10.107085] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 10.107102] io scheduler noop registered [ 10.107114] io scheduler deadline registered [ 10.107229] io scheduler cfq registered (default) [ 10.108916] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 10.111828] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridge to bus 0000:00 [ 10.111859] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 10.111880] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 10.111900] pci_bus 0000:00: root bus resource [bus 00-ff] [ 10.112416] PCI: bus0: Fast back to back transfers disabled [ 10.112452] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 10.112951] PCI: bus1: Fast back to back transfers enabled [ 10.113033] pci 0000:00:01.0: PCI bridge to [bus 01] [ 10.113860] mv_xor f1060800.xor: Marvell shared XOR driver [ 10.173807] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 10.174115] mv_xor f1060900.xor: Marvell shared XOR driver [ 10.233783] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 10.234408] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 10.236296] console [ttyS0] disabled [ 10.236391] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A [ 10.900719] console [ttyS0] enabled [ 10.915482] loop: module loaded [ 10.919385] sata_mv f1080000.sata: slots 32 ports 1 [ 10.926455] scsi host0: sata_mv [ 10.929934] ata1: SATA max UDMA/133 irq 32 [ 10.935202] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 10.941597] nand: Hynix H27U1G8F2BTR-BC [ 10.945468] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 10.953044] Scanning device for bad blocks [ 11.072842] 5 cmdlinepart partitions found on MTD device orion_nand [ 11.079083] Creating 5 MTD partitions on "orion_nand": [ 11.084242] 0x000000000000-0x000000200000 : "u-boot" [ 11.090793] 0x000000200000-0x000000500000 : "uImage" [ 11.097380] 0x000000500000-0x000000800000 : "uImage2" [ 11.104078] 0x000000800000-0x000001000000 : "failsafe" [ 11.110950] 0x000001000000-0x000008000000 : "root" [ 11.120199] libphy: Fixed MDIO Bus: probed [ 11.125461] libphy: orion_mdio_bus: probed [ 11.136162] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 11.264296] ata1: SATA link down (SStatus 0 SControl F300) [ 12.249896] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:a7:5b [ 12.258771] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.265340] ehci-pci: EHCI PCI platform driver [ 12.269867] ehci-orion: EHCI orion driver [ 12.274188] orion-ehci f1050000.ehci: EHCI Host Controller [ 12.279694] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 12.287596] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 12.322677] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 12.328990] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 12.335798] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.343024] usb usb1: Product: EHCI Host Controller [ 12.347888] usb usb1: Manufacturer: Linux 4.13.3_1 ehci_hcd [ 12.353467] usb usb1: SerialNumber: f1050000.ehci [ 12.359107] hub 1-0:1.0: USB hub found [ 12.362976] hub 1-0:1.0: 1 port detected [ 12.367775] usbcore: registered new interface driver usb-storage [ 12.374344] mousedev: PS/2 mouse device common for all mice [ 12.722677] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 12.914976] usb 1-1: New USB device found, idVendor=090c, idProduct=1000 [ 12.921673] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 12.928829] usb 1-1: Product: USB DISK [ 12.932565] usb 1-1: Manufacturer: SMI Corporation [ 12.938403] usb-storage 1-1:1.0: USB Mass Storage device detected [ 12.945004] scsi host1: usb-storage 1-1:1.0 [ 13.442669] rtc-mv f1010300.rtc: internal RTC not ticking [ 13.448299] i2c /dev entries driver [ 13.453860] hidraw: raw HID events driver (C) Jiri Kosina [ 13.459802] drop_monitor: Initializing network drop monitor service [ 13.466510] NET: Registered protocol family 17 [ 13.471048] Key type dns_resolver registered [ 13.476515] registered taskstats version 1 [ 13.480596] Loading compiled-in X.509 certificates [ 13.485496] zswap: loaded using pool lzo/zbud [ 13.503678] Key type big_key registered [ 13.520175] Key type encrypted registered [ 13.526314] hctosys: unable to open rtc device (rtc0) [ 13.536422] Freeing unused kernel memory: 1024K [ 14.100284] dracut: dracut-046 [ 14.286767] scsi 1:0:0:0: Direct-Access SMI USB DISK 1100 PQ: 0 ANSI: 4 [ 14.304928] sd 1:0:0:0: [sda] 15730688 512-byte logical blocks: (8.05 GB/7.50 GiB) [ 14.320763] sd 1:0:0:0: [sda] Write Protect is off [ 14.336526] sd 1:0:0:0: [sda] No Caching mode page found [ 14.341902] sd 1:0:0:0: [sda] Assuming drive cache: write through [ 14.370000] sda: sda1 [ 14.379079] sd 1:0:0:0: [sda] Attached SCSI removable disk [ 14.642245] systemd-udevd[183]: starting version 3.2.4 [ 14.663629] udevd[184]: starting eudev-3.2.4 [ 15.128556] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 15.307889] usbcore: registered new interface driver uas [ 15.450271] mvsdio f1090000.mvsdio: Got CD GPIO [ 15.505688] mvsdio f1090000.mvsdio: Got WP GPIO [ 15.953225] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 15.974823] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 16.257174] dracut: Checking ext3: /dev/disk/by-label/rootfs [ 16.265753] dracut: issuing e2fsck -a /dev/disk/by-label/rootfs [ 16.359341] dracut: rootfs: clean, 8998/491520 files, 98475/1966080 blocks [ 16.394506] dracut: Mounting /dev/disk/by-label/rootfs with -o defaults [ 16.481352] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 16.504562] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 16.655543] dracut: Mounted root filesystem /dev/sda1 [ 17.125111] dracut: Switching root - runit: $Id: 25da3b86f7bed4038b8a039d2f8e8c9bbcf0822b $: booting. - runit: enter stage: /etc/runit/1 => Welcome to Void! => Mounting pseudo-filesystems... [ 17.952863] raid6: int32x1 gen() 63 MB/s [ 18.123295] raid6: int32x1 xor() 42 MB/s [ 18.292837] raid6: int32x2 gen() 78 MB/s [ 18.462976] raid6: int32x2 xor() 60 MB/s [ 18.632901] raid6: int32x4 gen() 81 MB/s [ 18.802851] raid6: int32x4 xor() 55 MB/s [ 18.973168] raid6: int32x8 gen() 84 MB/s [ 19.143055] raid6: int32x8 xor() 57 MB/s [ 19.147314] raid6: using algorithm int32x8 gen() 84 MB/s [ 19.152599] raid6: .... xor() 57 MB/s, rmw enabled [ 19.157401] raid6: using intx1 recovery algorithm [ 19.165438] xor: measuring software checksum speed [ 19.262700] arm4regs : 726.000 MB/sec [ 19.362722] 8regs : 436.000 MB/sec [ 19.462650] 32regs : 634.000 MB/sec [ 19.466823] xor: using function: arm4regs (726.000 MB/sec) [ 19.627082] Btrfs loaded, crc32c=crc32c-generic [ 19.658523] tun: Universal TUN/TAP device driver, 1.6 [ 19.692327] PPP generic driver version 2.4.2 [ 19.748812] device-mapper: uevent: version 1.0.3 [ 19.753925] device-mapper: ioctl: 4.36.0-ioctl (2017-06-09) initialised: dm-devel@redhat.com [ 19.971918] Bluetooth: Core ver 2.22 [ 19.975681] NET: Registered protocol family 31 [ 19.980107] Bluetooth: HCI device and connection manager initialized [ 19.986482] Bluetooth: HCI socket layer initialized [ 19.991345] Bluetooth: L2CAP socket layer initialized [ 19.996472] Bluetooth: SCO socket layer initialized => Loading kernel modules... => Starting udev and waiting for devices to settle... [ 20.240414] udevd[361]: starting version 3.2.4 [ 20.302068] udevd[362]: starting eudev-3.2.4 [ 21.180807] orion_wdt: Initial timeout 25 sec [ 21.328545] marvell-cesa f1030000.crypto: CESA device successfully registered => Remounting rootfs read-only... [ 22.734682] EXT4-fs (sda1): re-mounted. Opts: data=ordered => Activating btrfs devices... Scanning for Btrfs filesystems [ 23.343099] random: crng init done => Activating encrypted devices... => Checking filesystems: => Mounting rootfs read-write... [ 23.503376] EXT4-fs (sda1): re-mounted. Opts: data=ordered => Mounting all non-network filesystems... => Initializing swap... => Initializing random seed... => Setting up loopback interface... => Setting up hostname to 'longshot-musl'... => Loading sysctl(8) settings... * Applying /usr/lib/sysctl.d/void.conf ... kernel.core_uses_pid = 1 fs.protected_hardlinks = 1 fs.protected_symlinks = 1 kernel.kptr_restrict = 1 kernel.dmesg_restrict = 1 kernel.perf_event_paranoid = 2 kernel.kexec_load_disabled = 1 sysctl: cannot stat /proc/sys/kernel/yama/ptrace_scope: error code 2 * Applying /etc/sysctl.conf ... => Initialization complete, running stage 2... - runit: leave stage: /etc/runit/1 - runit: enter stage: /etc/runit/2 runsvchdir: default: current. [ 24.955903] udevd[424]: starting version 3.2.4 [ 24.993278] udevd[424]: starting eudev-3.2.4 [ 25.428640] NET: Registered protocol family 10 Void 4.13.3_1 (longshot-musl) (console) void-live login: root Password: Last login: Thu Jan 1 00:00:32 on console # xbps-uhelper arch armv5tel-musl # uname -a Linux longshot-musl 4.13.3_1 #1 PREEMPT Tue Sep 26 06:20:29 UTC 2017 armv5tel GNU/Linux # df -h Filesystem Size Used Avail Use% Mounted on devtmpfs 52M 0 52M 0% /dev tmpfs 58M 0 58M 0% /dev/shm tmpfs 58M 132K 58M 1% /run /dev/sda1 7.4G 201M 6.8G 3% / cgroup 58M 0 58M 0% /sys/fs/cgroup tmpfs 58M 0 58M 0% /tmp # free -m total used free shared buff/cache available Mem: 114 11 76 0 26 98 Swap: 0 0 0 # pstree runit---runsvdir-,-runsv---sshd |-runsv---login---sh---pstree |-runsv---dhcpcd |-runsv---udevd
Re: PogoPlug Mobile - Stuck at "booting the kernel." September 28, 2017 03:18AM |
Admin Registered: 13 years ago Posts: 18,570 |