Re: Debian on Dell Kace M300 September 08, 2019 06:25PM |
Registered: 9 years ago Posts: 39 |
fw_setenv bootcmd_stock 'setenv mainlineLinux no; echo Booting stock ...; run bootcmd_ide'
setenv set_bootargs_stock 'setenv bootargs console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) root=/dev/sda1 rw'
Re: Debian on Dell Kace M300 September 08, 2019 06:35PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Debian on Dell Kace M300 September 08, 2019 07:24PM |
Registered: 10 years ago Posts: 155 |
Re: Debian on Dell Kace M300 September 08, 2019 07:39PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
Right! that's the intent in the Intstallation post above (it appears only once in the steps and not at all in Post-Installation).
Re: Debian on Dell Kace M300 September 09, 2019 03:40AM |
Admin Registered: 13 years ago Posts: 18,821 |
setenv set_bootargs_stock 'setenv mainlineLinux no; setenv bootargs_console console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) root=LABEL=root rw'
fw_setenv set_bootargs_stock 'setenv mainlineLinux no; setenv bootargs_console console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) root=LABEL=root rw'
Re: Debian on Dell Kace M300 September 09, 2019 07:30AM |
Registered: 9 years ago Posts: 39 |
Re: Debian on Dell Kace M300 September 09, 2019 09:36AM |
Registered: 7 years ago Posts: 369 |
Re: Debian on Dell Kace M300 September 09, 2019 09:40AM |
Registered: 7 years ago Posts: 369 |
Re: Debian on Dell Kace M300 September 09, 2019 09:52AM |
Registered: 7 years ago Posts: 369 |
run kernel_config run set_bootargs ide reset ext2load ide 0:1 $(load_uimage_addr) /boot/uImage ext2load ide 0:1 $(load_initrd_addr) /boot/uInitrd bootm $(load_uimage_addr) $(load_initrd_addr)
Re: Debian on Dell Kace M300 September 09, 2019 09:58AM |
Registered: 7 years ago Posts: 369 |
Re: Debian on Dell Kace M300 September 09, 2019 04:50PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Debian on Dell Kace M300 September 09, 2019 06:18PM |
Registered: 7 years ago Posts: 369 |
Re: Debian on Dell Kace M300 September 09, 2019 07:21PM |
Registered: 10 years ago Posts: 155 |
Re: Debian on Dell Kace M300 September 09, 2019 11:37PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Debian on Dell Kace M300 September 11, 2019 04:09AM |
Admin Registered: 13 years ago Posts: 18,821 |
root@dellkaceM300:~# ll /sys/class/leds/ total 0 lrwxrwxrwx 1 root root 0 Sep 11 08:59 orange -> ../../devices/platform/leds-gpio/leds/orange lrwxrwxrwx 1 root root 0 Sep 11 08:59 white -> ../../devices/platform/leds-gpio/leds/whiteThe above means there is at least one controllable LED light, and it could be turned on as White or Orange.
Re: Debian on Dell Kace M300 September 11, 2019 08:15AM |
Registered: 10 years ago Posts: 155 |
Re: Debian on Dell Kace M300 September 11, 2019 11:49AM |
Registered: 9 years ago Posts: 39 |
root@Gilrain:/sys/firmware/devicetree/base/gpio-leds# ls -l total 0 drwxr-xr-x 3 root root 0 Sep 11 11:19 . drwxr-xr-x 10 root root 0 Sep 11 11:19 .. -r--r--r-- 1 root root 10 Sep 11 11:19 compatible -r--r--r-- 1 root root 10 Sep 11 11:19 name -r--r--r-- 1 root root 4 Sep 11 11:19 pinctrl-0 -r--r--r-- 1 root root 8 Sep 11 11:19 pinctrl-names drwxr-xr-x 2 root root 0 Sep 11 11:19 white-sys root@Gilrain:/sys/firmware/devicetree/base/gpio-leds# cd white-sys/ root@Gilrain:/sys/firmware/devicetree/base/gpio-leds/white-sys# ls -l total 0 drwxr-xr-x 2 root root 0 Sep 11 11:19 . drwxr-xr-x 3 root root 0 Sep 11 11:19 .. -r--r--r-- 1 root root 12 Sep 11 11:19 gpios -r--r--r-- 1 root root 15 Sep 11 11:19 label -r--r--r-- 1 root root 11 Sep 11 11:19 linux,default-trigger -r--r--r-- 1 root root 10 Sep 11 11:19 name root@Gilrain:/sys/firmware/devicetree/base/gpio-leds/white-sys#
Re: Debian on Dell Kace M300 September 11, 2019 02:08PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
How to control GPIO in Linux userspace for GPIO-enable fan
Re: Debian on Dell Kace M300 September 11, 2019 02:13PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Debian on Dell Kace M300 September 11, 2019 02:29PM |
Registered: 9 years ago Posts: 39 |
Re: Debian on Dell Kace M300 September 11, 2019 02:46PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Debian on Dell Kace M300 September 11, 2019 07:06PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Debian on Dell Kace M300 September 12, 2019 01:57AM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Debian on Dell Kace M300 September 12, 2019 04:46AM |
Admin Registered: 13 years ago Posts: 18,821 |
echo default-on > /sys/class/leds/m300\:white\:sys/trigger echo none > /sys/class/leds/m300\:white\:sys/trigger
echo default-on > /sys/class/leds/m300\:orange\:sys/trigger echo none > /sys/class/leds/m300\:orange\:sys/trigger
echo heartbeat > /sys/class/leds/m300\:orange\:sys/trigger echo heartbeat > /sys/class/leds/m300\:white\:sys/trigger
Re: Debian on Dell Kace M300 September 12, 2019 07:31AM |
Registered: 9 years ago Posts: 39 |
Re: Debian on Dell Kace M300 September 12, 2019 09:14PM |
Registered: 10 years ago Posts: 155 |
Re: Debian on Dell Kace M300 September 13, 2019 02:45PM |
Registered: 9 years ago Posts: 429 |
Re: Debian on Dell Kace M300 September 13, 2019 03:00PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Debian on Dell Kace M300 September 13, 2019 04:32PM |
Registered: 10 years ago Posts: 155 |
Re: Debian on Dell Kace M300 September 13, 2019 06:51PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
Updated 24 Jul 2017:
Basic Debian stretch Kirkwood rootfs for most Kirwood plugs:
- tarball size: 188M
- install size: 488M
- The init system used in this rootfs is sysvinit . To boot with systemd, see note 2 below.
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, isc-dhcp-client, dialog, bzip2, nfs server/client, iperf, ethtool, sysvinit-core, sysvinit, and sysvinit-utils.
- see LED controls in /etc/rc.local, and /etc/init.d/halt
- see some useful aliases in /root/.profile
- root password: root
Download at Dropbox:
Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2
Quote
Updated 20 Feb 2016:
This Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 is to keep in sync with kernel Linux-4.4.0-kirkwood-tld-1.
Basic minimal Debian Kirkwood rootfs for most Kirwood plugs:
- tarball size: 137M
- install size: 398M
- a basic jessie rootfs.
- The init system used in this rootfs is sysvinit . To boot with systemd, see note 2 below.
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, isc-dhcp-client, dialog, bzip2, nfs server/client, iperf, ethtool, sysvinit-core, sysvinit, and sysvinit-utils.
- see LED controls in /etc/rc.local, and /etc/init.d/halt
- see some useful aliases in /root/.profile
- root password: root
Download at Dropbox:
Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2
md5:
9f957e1dc5a36f90a285ab4615cb02fd
sha256:
d33349118e34bd078ca635cd2d6776f3e312accfc77d29da5870b9980add5c36
And remember to check the hash of what you download, as always.