Re: Debian on Dell Kace M300 September 21, 2019 04:45PM |
Registered: 11 years ago Posts: 155 |
Re: Debian on Dell Kace M300 September 21, 2019 05:40PM |
Admin Registered: 13 years ago Posts: 19,102 |
Quote
> You're missing a "run":setenv bootcmd 'run > kernel_config; run set_bootargs_usb; run > bootcmd_usb; run set_bootargs_sata; run > bootcmd_ide'
Quote
3.a. Execute the following command to unprotect the SPI flash:
protect off all
protect off all
Re: Debian on Dell Kace M300 September 21, 2019 06:11PM |
Registered: 11 years ago Posts: 155 |
Re: Debian on Dell Kace M300 September 21, 2019 06:55PM |
Admin Registered: 13 years ago Posts: 19,102 |
Re: Debian on Dell Kace M300 September 21, 2019 07:49PM |
Registered: 11 years ago Posts: 155 |
Re: Debian on Dell Kace M300 September 21, 2019 08:17PM |
Registered: 7 years ago Posts: 375 |
Re: Debian on Dell Kace M300 September 21, 2019 10:18PM |
Admin Registered: 13 years ago Posts: 19,102 |
Re: Debian on Dell Kace M300 September 22, 2019 12:14AM |
Registered: 10 years ago Posts: 226 |
Re: Debian on Dell Kace M300 September 22, 2019 08:04AM |
Registered: 11 years ago Posts: 155 |
Re: Debian on Dell Kace M300 September 22, 2019 12:28PM |
Registered: 11 years ago Posts: 155 |
Begin: Running /scripts/local-block ... done. /init: line 329: blkid: not found /init: line 96: sleep: not found /init: line 97: cat: not found
Booting USB. (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found Waiting for storage device(s) to settle before scanning... T
Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 40.048254][ C0] rcu: INFO: rcu_preempt detected stalls on CPUs/tasks: [ 40.055081][ C0] rcu: Tasks blocked on level-0 rcu_node (CPUs 0-0): P1 [ 40.061987][ C0] (detected by 0, t=2102 jiffies, g=-35, q=268) [ 40.068186][ C0] run-init R running task 0 1 0 0x00000000 [ 40.075985][ C0] [<8010f8cc>] (unwind_backtrace) from [<8010bd1c>] (show_stack+0x10/0x14) [ 40.084468][ C0] [<8010bd1c>] (show_stack) from [<8017161c>] (rcu_sched_clock_irq+0x824/0x8f8) [ 40.093389][ C0] [<8017161c>] (rcu_sched_clock_irq) from [<801786fc>] (update_process_times+0x30/0x5c) [ 40.103008][ C0] [<801786fc>] (update_process_times) from [<801877f8>] (tick_sched_handle+0x54/0x60) [ 40.112448][ C0] [<801877f8>] (tick_sched_handle) from [<80187a3c>] (tick_sched_timer+0x48/0x9c) [ 40.121535][ C0] [<80187a3c>] (tick_sched_timer) from [<80179580>] (__hrtimer_run_queues.constprop.3+0x1b8/0x378) [ 40.132102][ C0] [<80179580>] (__hrtimer_run_queues.constprop.3) from [<80179a9c>] (hrtimer_interrupt+0xf8/0x2e0) [ 40.142671][ C0] [<80179a9c>] (hrtimer_interrupt) from [<80863f30>] (orion_clkevt_irq_handler+0x10/0x1c) [ 40.152456][ C0] [<80863f30>] (orion_clkevt_irq_handler) from [<80161650>] (__handle_irq_event_percpu+0xb8/0x210) [ 40.163022][ C0] [<80161650>] (__handle_irq_event_percpu) from [<801617cc>] (handle_irq_event_percpu+0x24/0x78) [ 40.173415][ C0] [<801617cc>] (handle_irq_event_percpu) from [<80161880>] (handle_irq_event+0x60/0x84) [ 40.183027][ C0] [<80161880>] (handle_irq_event) from [<80165c88>] (handle_edge_irq+0x16c/0x198) [ 40.192111][ C0] [<80165c88>] (handle_edge_irq) from [<80160888>] (generic_handle_irq+0x18/0x28) [ 40.201198][ C0] [<80160888>] (generic_handle_irq) from [<806388c8>] (orion_bridge_irq_handler+0x54/0x5c) [ 40.211069][ C0] [<806388c8>] (orion_bridge_irq_handler) from [<80160888>] (generic_handle_irq+0x18/0x28) [ 40.220940][ C0] [<80160888>] (generic_handle_irq) from [<80160f4c>] (__handle_domain_irq+0xac/0xcc) [ 40.230374][ C0] [<80160f4c>] (__handle_domain_irq) from [<80638868>] (orion_handle_irq+0x78/0x84) [ 40.239636][ C0] [<80638868>] (orion_handle_irq) from [<80102188>] (__irq_svc+0x68/0x9c) [ 40.248020][ C0] Exception stack(0xeecb3cf0 to 0xeecb3d38) [ 40.253784][ C0] 3ce0: ee47e750 eecb3e20 ef0e8000 ee47e760 [ 40.262699][ C0] 3d00: ee47f0f8 ee47e750 82799019 ee40a660 eecb3e20 eecb3db4 3245d2f6 00000007 [ 40.271609][ C0] 3d20: 00000000 eecb3d40 80277c00 80284e7c a0000013 ffffffff [ 40.278955][ C0] [<80102188>] (__irq_svc) from [<80284e7c>] (__d_lookup_rcu+0x3c/0x124) [ 40.287257][ C0] [<80284e7c>] (__d_lookup_rcu) from [<80277c00>] (lookup_fast+0x48/0x2c0) [ 40.295731][ C0] [<80277c00>] (lookup_fast) from [<802780fc>] (walk_component+0xdc/0x288) [ 40.304207][ C0] [<802780fc>] (walk_component) from [<802792e8>] (path_lookupat+0x124/0x204) [ 40.312945][ C0] [<802792e8>] (path_lookupat) from [<8027b568>] (filename_lookup+0x6c/0xd8) [ 40.321599][ C0] [<8027b568>] (filename_lookup) from [<80271a78>] (vfs_statx+0x6c/0xcc) [ 40.329897][ C0] [<80271a78>] (vfs_statx) from [<802722b8>] (sys_lstat64+0x34/0x6c) [ 40.337849][ C0] [<802722b8>] (sys_lstat64) from [<80101000>] (ret_fast_syscall+0x0/0x50) [ 40.346320][ C0] Exception stack(0xeecb3fa8 to 0xeecb3ff0) [ 40.352086][ C0] 3fa0: 00edde70 76f43968 00edde70 7ec739b8 7ec739b8 e196e600 [ 40.360999][ C0] 3fc0: 00edde70 76f43968 00000001 000000c4 00eddf90 00edde70 7ec73c80 005a69ac [ 40.369909][ C0] 3fe0: 005a6f28 7ec739b0 005338bc 76e62844 [ 103.098253][ C0] rcu: INFO: rcu_preempt detected stalls on CPUs/tasks: [ 103.105076][ C0] rcu: Tasks blocked on level-0 rcu_node (CPUs 0-0): P1 [ 103.111982][ C0] (detected by 0, t=8407 jiffies, g=-35, q=268) [ 103.118180][ C0] run-init R running task 0 1 0 0x00000000 [ 103.125971][ C0] [<8010f8cc>] (unwind_backtrace) from [<8010bd1c>] (show_stack+0x10/0x14) [ 103.134453][ C0] [<8010bd1c>] (show_stack) from [<8017161c>] (rcu_sched_clock_irq+0x824/0x8f8) [ 103.143365][ C0] [<8017161c>] (rcu_sched_clock_irq) from [<801786fc>] (update_process_times+0x30/0x5c) [ 103.152974][ C0] [<801786fc>] (update_process_times) from [<801877f8>] (tick_sched_handle+0x54/0x60) [ 103.162408][ C0] [<801877f8>] (tick_sched_handle) from [<80187a3c>] (tick_sched_timer+0x48/0x9c) [ 103.171495][ C0] [<80187a3c>] (tick_sched_timer) from [<80179580>] (__hrtimer_run_queues.constprop.3+0x1b8/0x378) [ 103.182061][ C0] [<80179580>] (__hrtimer_run_queues.constprop.3) from [<80179a9c>] (hrtimer_interrupt+0xf8/0x2e0) [ 103.192630][ C0] [<80179a9c>] (hrtimer_interrupt) from [<80863f30>] (orion_clkevt_irq_handler+0x10/0x1c) [ 103.202415][ C0] [<80863f30>] (orion_clkevt_irq_handler) from [<80161650>] (__handle_irq_event_percpu+0xb8/0x210) [ 103.212982][ C0] [<80161650>] (__handle_irq_event_percpu) from [<801617cc>] (handle_irq_event_percpu+0x24/0x78) [ 103.223374][ C0] [<801617cc>] (handle_irq_event_percpu) from [<80161880>] (handle_irq_event+0x60/0x84) [ 103.232986][ C0] [<80161880>] (handle_irq_event) from [<80165c88>] (handle_edge_irq+0x16c/0x198) [ 103.242072][ C0] [<80165c88>] (handle_edge_irq) from [<80160888>] (generic_handle_irq+0x18/0x28) [ 103.251157][ C0] [<80160888>] (generic_handle_irq) from [<806388c8>] (orion_bridge_irq_handler+0x54/0x5c) [ 103.261029][ C0] [<806388c8>] (orion_bridge_irq_handler) from [<80160888>] (generic_handle_irq+0x18/0x28) [ 103.270898][ C0] [<80160888>] (generic_handle_irq) from [<80160f4c>] (__handle_domain_irq+0xac/0xcc) [ 103.280334][ C0] [<80160f4c>] (__handle_domain_irq) from [<80638868>] (orion_handle_irq+0x78/0x84) [ 103.289595][ C0] [<80638868>] (orion_handle_irq) from [<80102188>] (__irq_svc+0x68/0x9c) [ 103.297980][ C0] Exception stack(0xeecb3cf0 to 0xeecb3d38) [ 103.303745][ C0] 3ce0: ee47f6c8 eecb3e20 ef0e8000 ee47f6d8 [ 103.312659][ C0] 3d00: ee47f290 ee47f6c8 82799019 ee40a660 eecb3e20 eecb3db4 3245d2f6 00000007 [ 103.321569][ C0] 3d20: 00000000 eecb3d40 80277c00 80284f54 20000013 ffffffff [ 103.328914][ C0] [<80102188>] (__irq_svc) from [<80284f54>] (__d_lookup_rcu+0x114/0x124) [ 103.337303][ C0] [<80284f54>] (__d_lookup_rcu) from [<80277c00>] (lookup_fast+0x48/0x2c0) [ 103.345779][ C0] [<80277c00>] (lookup_fast) from [<802780fc>] (walk_component+0xdc/0x288) [ 103.354254][ C0] [<802780fc>] (walk_component) from [<802792e8>] (path_lookupat+0x124/0x204) [ 103.362992][ C0] [<802792e8>] (path_lookupat) from [<8027b568>] (filename_lookup+0x6c/0xd8) [ 103.371644][ C0] [<8027b568>] (filename_lookup) from [<80271a78>] (vfs_statx+0x6c/0xcc) [ 103.379945][ C0] [<80271a78>] (vfs_statx) from [<802722b8>] (sys_lstat64+0x34/0x6c) [ 103.387895][ C0] [<802722b8>] (sys_lstat64) from [<80101000>] (ret_fast_syscall+0x0/0x50) [ 103.396366][ C0] Exception stack(0xeecb3fa8 to 0xeecb3ff0) [ 103.402133][ C0] 3fa0: 00edde70 76f43968 00edde70 7ec739b8 7ec739b8 e196e600 [ 103.411046][ C0] 3fc0: 00edde70 76f43968 00000001 000000c4 00eddf90 00edde70 7ec73c80 005a69ac [ 103.419955][ C0] 3fe0: 005a6f28 7ec739b0 005338bc 76e62844 [ 129.728291][ C0] random: crng init done
Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.33.1 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 sata_rootfs: clean, 24989/524288 files, 395085/2097152 blocks done. [ 18.859131][ T194] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 18.877622][ T194] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Starting hotplug events dispatcher: systemd-udevd. [ ok ] Synthesizing the initial hotplug events (subsystems)...done. [....] Synthesizing the initial hotplug events (devices)...[ 20.358526][ T375] systemd-udevd[375]: Using default interface naming scheme 'v240'. done. [....] Waiting for /dev to be fully populated...[ 20.505373][ T375] systemd-udevd[375]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 20.697056][ T395] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range [ 20.847727][ T395] watchdog: f1020300.watchdog-timer: falling back to default timeout (21) [ 20.876659][ T396] marvell-cesa f1030000.crypto: CESA device successfully registered [ 20.897808][ T398] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 20.921011][ T395] orion_wdt: Initial timeout 21 sec [ 20.997447][ T396] systemd-udevd[396]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. done. [ ok ] Setting hostname to 'Dell-M300'...done. [ ok ] Activating swap:. [ 21.957541][ T595] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [info] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=sata_rootfs is mounted LABEL=Data is not mounted [/sbin/fsck.ext4 (1) -- /mnt/data] fsck.ext4 -y -C0 /dev/sda2 e2fsck 1.44.5 (15-Dec-2018) Data: clean, 1989/6807552 files, 9954062/27207798 blocks [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [....] Will now mount local filesystems:[ 23.245807][ T878] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) . ok [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Starting Setting kernel variables: sysctl. [....] Initializing random number generator...[ 23.957143][ T1072] random: dd: uninitialized urandom read (512 bytes read) done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/18:03:73:41:db:3e Sending on LPF/eth0/18:03:73:41:db:3e Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 [ 25.880302][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 18 DHCPOFFER of 192.168.1.104 from 192.168.1.1 DHCPREQUEST for 192.168.1.104 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.104 from 192.168.1.1 bound to 192.168.1.104 -- renewal in 35603 seconds. [ 33.990429][ T1151] NET: Registered protocol family 10 [ 33.996641][ T1151] Segment Routing with IPv6 done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1362 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1389 (klogd) . ok [....] Starting system message bus: dbus[ 37.417901][ T1419] random: dbus-daemon: uninitialized urandom read (12 bytes read) [ 37.440138][ T1419] random: dbus-daemon: uninitialized urandom read (12 bytes read) . ok [....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon[ 37.551837][ T1442] random: avahi-daemon: uninitialized urandom read (4 bytes read) . ok [ ok ] Starting entropy daemon: haveged. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [....] Starting OpenBSD Secure Shell server: sshd[ 39.888639][ T1471] random: crng init done [ 39.892983][ T1471] random: 1 urandom warning(s) missed due to ratelimiting . ok Making sure that Logitech Media Server is not running first: No process in pidfile '/var/run/logitechmediaserver.pid' found running; none killed. Starting Logitech Media Server. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 10 Dell-M300 ttyS0 Dell-M300 login:
Re: Debian on Dell Kace M300 September 22, 2019 02:23PM |
Registered: 10 years ago Posts: 226 |
Booting USB. (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found Waiting for storage device(s) to settle before scanning... TI saw this many times. I think it's trying to boot off the USB and if you wait long enough it will eventually try IDE and successfully boot.
Re: Debian on Dell Kace M300 September 22, 2019 02:40PM |
Registered: 11 years ago Posts: 155 |
Re: Debian on Dell Kace M300 September 22, 2019 05:33PM |
Admin Registered: 13 years ago Posts: 19,102 |
Re: Debian on Dell Kace M300 September 22, 2019 05:55PM |
Admin Registered: 13 years ago Posts: 19,102 |
Re: Debian on Dell Kace M300 September 22, 2019 06:08PM |
Registered: 11 years ago Posts: 155 |
Re: Debian on Dell Kace M300 September 22, 2019 06:10PM |
Registered: 6 years ago Posts: 258 |
Re: Debian on Dell Kace M300 September 22, 2019 06:17PM |
Admin Registered: 13 years ago Posts: 19,102 |
Re: Debian on Dell Kace M300 September 22, 2019 06:55PM |
Registered: 7 years ago Posts: 375 |
Re: Debian on Dell Kace M300 September 22, 2019 07:01PM |
Admin Registered: 13 years ago Posts: 19,102 |
printenv
Re: Debian on Dell Kace M300 September 22, 2019 07:02PM |
Registered: 7 years ago Posts: 375 |
Re: Debian on Dell Kace M300 September 22, 2019 07:07PM |
Registered: 7 years ago Posts: 375 |
CASset=min MALLOC_len=1 arcNumber=11 autoload=no baudrate=115200 bootargs=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) bootargs_console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) bootargs_end=:::DB88FXX81:eth0:none bootargs_root=root=/dev/nfs rw bootcmd2=ide reset; ext2load ide 0:2 0x100000 /kbox/bin/uImage.bak; ext2load ide 0:1 0x01100000 /uInitrd;bootm 0x100000 0x01100000 bootcmd=run kernel_config; run set_bootargs; run bootcmd_ide2; run bootcmd_exec bootcmd_exec=echo Booting Debian â¦; usb start; run load_uimage; run load_initrd; bootm $(load_uimage_addr) $(load_initrd_addr) bootcmd_ide2=ide reset; ext2load ide 0:1 $(load_uimage_addr) /boot/uImage; ext2load ide 0:1 $(load_initrd_addr) /boot/uInitrd; bootm $(load_uimage_addr) $(load_initrd_addr) bootcmd_ide=run bootcmd_ideload; setenv bootargs $(bootargs_console); bootm 0x100000 0x01100000 bootcmd_ideload=ide reset; ext2load ide 0:1 0x100000 /uImage; ext2load ide 0:1 0x01100000 /uInitrd bootdelay=3 console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) disL2Cache=no disL2Prefetch=yes disaMvPnp=no enaAutoRecovery=yes enaCpuStream=no enaDCPref=yes enaICPref=yes enaMonExt=no enaWrAllo=no ethact=egiga0 ethaddr=18:03:73:41:dc:65 ethmtu=1500 ethprime=egiga0 fileaddr=1200000 filesize=728c0 image_name=uImage ipaddr=192.168.7.38 kernel2bootup=no kernel_config=setenv mainlineLinux yes; setenv mtdparts mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env); setenv load_uimage_addr 0x800000; setenv load_initrd_addr 0x02100000 load_initrd=ext2load usb 0:1 $(load_initrd_addr) /boot/uInitrd load_initrd_addr=0x02100000 load_uimage=ext2load usb 0:1 $(load_uimage_addr) /boot/uImage load_uimage_addr=0x800000 loadaddr=0x02000000 loads_echo=0 mainlineLinux=yes mtdparts=mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs netbsd_en=no netmask=255.255.255.0 netretry=no pcieTune=no pexMode=RC rcvrip=169.254.100.100 rootpath=/mnt/ARM_FS/ run_diag=yes sata_dma_mode=yes serverip=192.168.58.188 setL2CacheWT=yes set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $(mtdparts) earlyprintk=serial standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usiversion=kacemini-1.5 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81
Re: Debian on Dell Kace M300 September 22, 2019 07:10PM |
Registered: 7 years ago Posts: 375 |
CASset=min MALLOC_len=1 autoload=no baudrate=115200 bootargs=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) root=/dev/sda1 rw bootargs_console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) bootargs_end=:::DB88FXX81:eth0:none bootargs_root=root=/dev/nfs rw bootcmd2=ide reset; ext2load ide 0:2 0x100000 /kbox/bin/uImage.bak; ext2load ide 0:1 0x01100000 /uInitrd;bootm 0x100000 0x01100000 bootcmd=run kernel_config; run set_bootargs; run bootcmd_ide2; run bootcmd_exec bootcmd_exec=echo Booting Debian â¦; usb start; run load_uimage; run load_initrd; bootm $(load_uimage_addr) $(load_initrd_addr) bootcmd_ide2=ide reset; ext2load ide 0:1 $(load_uimage_addr) /boot/uImage; ext2load ide 0:1 $(load_initrd_addr) /boot/uInitrd; bootm $(load_uimage_addr) $(load_initrd_addr) bootcmd_ide=run bootcmd_ideload; setenv bootargs $(bootargs_console); bootm 0x100000 0x01100000 bootcmd_ideload=ide reset; ext2load ide 0:1 0x100000 /uImage; ext2load ide 0:1 0x01100000 /uInitrd bootdelay=3 console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) disL2Cache=no disL2Prefetch=yes disaMvPnp=no enaAutoRecovery=yes enaCpuStream=no enaDCPref=yes enaICPref=yes enaMonExt=no enaWrAllo=no ethact=egiga0 ethaddr=18:03:73:41:dc:08 ethmtu=1500 ethprime=egiga0 fileaddr=1200000 filesize=728c0 image_name=uImage ipaddr=192.168.58.233 kernel2bootup=no kernel_config=setenv mainlineLinux yes; setenv mtdparts mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env); setenv load_uimage_addr 0x800000; setenv load_initrd_addr 0x02100000 load_initrd=ext2load usb 0:1 $(load_initrd_addr) /boot/uInitrd load_uimage=ext2load usb 0:1 $(load_uimage_addr) /boot/uImage loadaddr=0x02000000 loads_echo=0 mainlineLinux=no mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs netbsd_en=no netmask=255.255.255.0 netretry=no pcieTune=no pexMode=RC rcvrip=169.254.100.100 rootpath=/mnt/ARM_FS/ run_diag=yes sata_dma_mode=yes serverip=192.168.58.188 setL2CacheWT=yes set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $(mtdparts) earlyprintk=serial standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usiversion=kacemini-1.5 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81
Re: Debian on Dell Kace M300 September 22, 2019 07:18PM |
Registered: 11 years ago Posts: 155 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Jun 20 2011 - 13:16:26) Marvell version: 3.4.27 USISH-SMB Ver: kacemini-1.5 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CDBC0 Soc: MV88F1155 Rev 1 (DDR3) CPU running @ 2000Mhz L2 running @ 500Mhz SysClock = 500Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7 DRAM CS[0] base 0x00000000 size 512MB DRAM CS[1] base 0x20000000 size 512MB DRAM CS[2] base 0x40000000 size 512MB DRAM CS[3] base 0x60000000 size 512MB DRAM Total size 2GB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done [512kB@f8000000] Flash: 512 kB Good CRC! CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Running diagnostics ... DDR3 data bus test PASSED DDR3 address bus test PASSED DDR3 device test PASSED Diag completed Hit any key to stop autoboot: 0 Booting USB. (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found Waiting for storage device(s) to settle before scanning... 0 Storage Device(s) found ** Bad partition 1 ** ** Bad partition 1 ** ## Booting image at 00800000 ... Bad Magic Number Booting IDE . Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: KINGSTON SA400S37120G Firm: SBFKB1D1 Ser#: 50026B7282368B97 Type: Hard Disk Supports 48-bit addressing Capacity: 114473.4 MB = 111.7 GB (234441648 x 512) 4981772 bytes read 9784769 bytes read ## Booting image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-2 Created: 2019-09-12 16:29:16 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4981708 Bytes = 4.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initramfs-5.2.9-kirkwood-tld-2 Created: 2019-09-07 16:57:30 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9784705 Bytes = 9.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.2.9-kirkwood-tld-2 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Wed Aug 28 03:55:21 PDT 2019 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Dell KACE M300 [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Ignoring RAM at 0x70000000-0x80000000 [ 0.000000][ T0] Consider using a HIGHMEM enabled kernel. [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 455168 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=sata_rootfs rootdelay=10 mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) earlyprintk=serial [ 0.000000][ T0] Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes) [ 0.000000][ T0] Inode-cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000][ T0] Memory: 1793952K/1835008K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 300K bss, 41056K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x52c/0x924 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000006][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008509][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.015620][ T0] Console: colour dummy device 80x30 [ 0.020802][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032004][ T0] pid_max: default: 32768 minimum: 301 [ 0.037556][ T0] LSM: Security Framework initializing [ 0.043022][ T0] Mount-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.050436][ T0] Mountpoint-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.058885][ T0] *** VALIDATE proc *** [ 0.063078][ T0] *** VALIDATE cgroup1 *** [ 0.067334][ T0] *** VALIDATE cgroup2 *** [ 0.071682][ T0] CPU: Testing write buffer coherency: ok [ 0.078550][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.085576][ T1] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1 [ 0.091631][ T1] rcu: Hierarchical SRCU implementation. [ 0.099348][ T1] devtmpfs: initialized [ 0.107022][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.117562][ T1] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.124576][ T1] xor: measuring software checksum speed [ 0.228529][ T1] arm4regs : 1816.800 MB/sec [ 0.328530][ T1] 8regs : 1090.400 MB/sec [ 0.428528][ T1] 32regs : 1585.600 MB/sec [ 0.433382][ T1] xor: using function: arm4regs (1816.800 MB/sec) [ 0.439650][ T1] prandom: seed boundary self test passed [ 0.447698][ T1] prandom: 100 self tests passed [ 0.452494][ T1] pinctrl core: initialized pinctrl subsystem [ 0.459515][ T1] NET: Registered protocol family 16 [ 0.465021][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.473225][ T1] audit: initializing netlink subsys (disabled) [ 0.480283][ T14] audit: type=2000 audit(0.470:1): state=initialized audit_enabled=0 res=1 [ 0.488794][ T1] cpuidle: using governor ladder [ 0.493619][ T1] cpuidle: using governor menu [ 0.498631][ T1] Feroceon L2: Enabling L2 [ 0.502909][ T1] Feroceon L2: Cache support initialised. [ 0.512292][ T1] No ATAGs? [ 2.568513][ C0] random: fast init done [ 3.736900][ T71] alg: No test for lzo-rle (lzo-rle-generic) [ 3.743049][ T73] alg: No test for lzo-rle (lzo-rle-scomp) [ 3.918826][ T1] raid6: int32x8 gen() 208 MB/s [ 4.088870][ T1] raid6: int32x8 xor() 142 MB/s [ 4.258773][ T1] raid6: int32x4 gen() 209 MB/s [ 4.428665][ T1] raid6: int32x4 xor() 138 MB/s [ 4.598569][ T1] raid6: int32x2 gen() 208 MB/s [ 4.768668][ T1] raid6: int32x2 xor() 152 MB/s [ 4.938707][ T1] raid6: int32x1 gen() 157 MB/s [ 5.108549][ T1] raid6: int32x1 xor() 109 MB/s [ 5.113485][ T1] raid6: using algorithm int32x4 gen() 209 MB/s [ 5.119553][ T1] raid6: .... xor() 138 MB/s, rmw enabled [ 5.125097][ T1] raid6: using intx1 recovery algorithm [ 5.130658][ T1] vgaarb: loaded [ 5.134386][ T1] SCSI subsystem initialized [ 5.139194][ T1] usbcore: registered new interface driver usbfs [ 5.145376][ T1] usbcore: registered new interface driver hub [ 5.151433][ T1] usbcore: registered new device driver usb [ 5.157274][ T1] pps_core: LinuxPPS API ver. 1 registered [ 5.162924][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 5.172720][ T1] PTP clock support registered [ 5.178257][ T1] clocksource: Switched to clocksource orion_clocksource [ 5.790857][ T1] VFS: Disk quotas dquot_6.6.0 [ 5.795522][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 5.809863][ T1] NET: Registered protocol family 2 [ 5.815468][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 1, 8192 bytes) [ 5.823958][ T1] TCP established hash table entries: 16384 (order: 4, 65536 bytes) [ 5.831973][ T1] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 5.839375][ T1] TCP: Hash tables configured (established 16384 bind 16384) [ 5.846639][ T1] UDP hash table entries: 1024 (order: 2, 16384 bytes) [ 5.853372][ T1] UDP-Lite hash table entries: 1024 (order: 2, 16384 bytes) [ 5.860682][ T1] NET: Registered protocol family 1 [ 5.866177][ T1] RPC: Registered named UNIX socket transport module. [ 5.872820][ T1] RPC: Registered udp transport module. [ 5.878185][ T1] RPC: Registered tcp transport module. [ 5.883567][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 5.890679][ T1] PCI: CLS 0 bytes, default 32 [ 5.895435][ T1] Trying to unpack rootfs image as initramfs... [ 6.437643][ T1] Freeing initrd memory: 9556K [ 6.442400][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 6.450487][ T1] Initialise system trusted keyrings [ 6.455624][ T1] Key type blacklist registered [ 6.460511][ T1] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 6.467661][ T1] zbud: loaded [ 6.471703][ T1] NFS: Registering the id_resolver key type [ 6.477433][ T1] Key type id_resolver registered [ 6.482350][ T1] Key type id_legacy registered [ 6.487039][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 6.494414][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 6.501668][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 6.509542][ T1] fuse: init (API version 7.31) [ 6.514486][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 6.521730][ T1] orangefs_init: module version upstream loaded [ 6.527793][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 6.548032][ T1] async_tx: api initialized (async) [ 6.553147][ T1] Key type asymmetric registered [ 6.557913][ T1] Asymmetric key parser 'x509' registered [ 6.563547][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 6.572637][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.581981][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 6.590265][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 6.596416][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 6.603968][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 6.610973][ T1] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400 [ 6.617660][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 6.625791][ T1] PCI: bus0: Fast back to back transfers disabled [ 6.632060][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 6.641406][ T1] PCI: bus1: Fast back to back transfers enabled [ 6.647563][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 6.654976][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref] [ 6.662876][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 6.668913][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.728808][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 6.738048][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.798767][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 6.808186][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.816117][ T1] printk: console [ttyS0] disabled [ 6.821158][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 6.830830][ T1] printk: console [ttyS0] enabled [ 6.830830][ T1] printk: console [ttyS0] enabled [ 6.840651][ T1] printk: bootconsole [earlycon0] disabled [ 6.840651][ T1] printk: bootconsole [earlycon0] disabled [ 6.857293][ T1] loop: module loaded [ 6.861609][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 6.869135][ T1] scsi host0: sata_mv [ 6.873416][ T1] scsi host1: sata_mv [ 6.877466][ T1] ata1: SATA max UDMA/133 irq 33 [ 6.882323][ T1] ata2: SATA max UDMA/133 irq 33 [ 6.888376][ T1] m25p80 spi0.0: mx25l4005a (512 Kbytes) [ 6.893901][ T1] 2 cmdlinepart partitions found on MTD device spi0.0 [ 6.900577][ T1] Creating 2 MTD partitions on "spi0.0": [ 6.906091][ T1] 0x000000000000-0x00000007f000 : "uboot" [ 6.912620][ T1] 0x00000007f000-0x000000080000 : "u-boot-env" [ 6.920303][ T1] libphy: Fixed MDIO Bus: probed [ 6.925656][ T1] libphy: orion_mdio_bus: probed [ 6.940274][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 6.948121][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 6.956045][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 18:03:73:41:db:3e [ 6.965641][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.972988][ T1] ehci-pci: EHCI PCI platform driver [ 6.978194][ T1] ehci-orion: EHCI orion driver [ 6.983091][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 6.989360][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 6.997906][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 7.028281][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 7.035199][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 7.044217][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.052181][ T1] usb usb1: Product: EHCI Host Controller [ 7.057773][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-2 ehci_hcd [ 7.065120][ T1] usb usb1: SerialNumber: f1050000.ehci [ 7.070974][ T1] hub 1-0:1.0: USB hub found [ 7.075467][ T1] hub 1-0:1.0: 1 port detected [ 7.080625][ T1] usbcore: registered new interface driver usb-storage [ 7.087608][ T1] mousedev: PS/2 mouse device common for all mice [ 7.094341][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 7.100072][ T1] i2c /dev entries driver [ 7.104722][ T1] device-mapper: uevent: version 1.0.3 [ 7.110319][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 7.119827][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 7.127111][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 7.134491][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 7.141925][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 7.148799][ T1] device-mapper: raid: Loading target version 1.14.0 [ 7.156140][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 7.162545][ T1] drop_monitor: Initializing network drop monitor service [ 7.169771][ T1] NET: Registered protocol family 17 [ 7.175138][ T1] Key type dns_resolver registered [ 7.180747][ T1] registered taskstats version 1 [ 7.185581][ T1] Loading compiled-in X.509 certificates [ 7.191269][ T1] zswap: loaded using pool lzo/zbud [ 7.259388][ T1] Key type big_key registered [ 7.292463][ T1] Key type encrypted registered [ 7.298907][ T1] rtc-mv f1010300.rtc: setting system clock to 2019-09-23T00:02:46 UTC (1569196966) [ 7.388293][ T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 7.395566][ T112] ata1.00: ATA-11: KINGSTON SA400S37120G, SBFKB1D1, max UDMA/133 [ 7.403195][ T112] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 7.411049][ T112] ata1.00: configured for UDMA/133 [ 7.426425][ T7] scsi 0:0:0:0: Direct-Access ATA KINGSTON SA400S3 B1D1 PQ: 0 ANSI: 5 [ 7.436046][ T116] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/112 GiB) [ 7.444704][ T116] sd 0:0:0:0: [sda] Write Protect is off [ 7.450274][ T15] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 7.457843][ T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.469093][ T116] sda: sda1 sda2 [ 7.473832][ T116] sd 0:0:0:0: [sda] Attached SCSI disk [ 7.658788][ T15] usb 1-1: New USB device found, idVendor=058f, idProduct=6254, bcdDevice= 1.00 [ 7.667714][ T15] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 7.676153][ T15] hub 1-1:1.0: USB hub found [ 7.680781][ T15] hub 1-1:1.0: 4 ports detected [ 7.781889][ T114] ata2: SATA link down (SStatus 0 SControl F300) [ 7.801407][ T1] Freeing unused kernel memory: 1024K [ 7.807049][ T1] Checked W+X mappings: passed, no W+X pages found [ 7.813451][ T1] Run /init as init process Loading, please wait... Starting version 241 [ 8.366679][ T168] input: gpio_keys as /devices/platform/gpio_keys/input/input0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.33.1 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 sata_rootfs: clean, 24982/524288 files, 395237/2097152 blocks done. [ 18.867661][ T194] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 18.886140][ T194] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Starting hotplug events dispatcher: systemd-udevd. [ ok ] Synthesizing the initial hotplug events (subsystems)...done. [....] Synthesizing the initial hotplug events (devices)...[ 20.421577][ T386] systemd-udevd[386]: Using default interface naming scheme 'v240'. done. [....] Waiting for /dev to be fully populated...[ 20.550471][ T386] systemd-udevd[386]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 20.683019][ T387] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range [ 20.804388][ T383] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 20.819039][ T387] watchdog: f1020300.watchdog-timer: falling back to default timeout (21) [ 20.967783][ T387] orion_wdt: Initial timeout 21 sec [ 20.985688][ T374] marvell-cesa f1030000.crypto: CESA device successfully registered [ 21.065667][ T386] systemd-udevd[386]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. done. [ ok ] Setting hostname to 'Dell-M300'...done. [ ok ] Activating swap:. [ 22.218358][ T595] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [info] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=sata_rootfs is mounted LABEL=Data is not mounted [/sbin/fsck.ext4 (1) -- /mnt/data] fsck.ext4 -y -C0 /dev/sda2 e2fsck 1.44.5 (15-Dec-2018) Data: clean, 1989/6807552 files, 9954062/27207798 blocks [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [....] Will now mount local filesystems:[ 23.517203][ T878] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) . ok [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Starting Setting kernel variables: sysctl. [....] Initializing random number generator...[ 24.231499][ T1072] random: dd: uninitialized urandom read (512 bytes read) done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/18:03:73:41:db:3e Sending on LPF/eth0/18:03:73:41:db:3e Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 [ 26.135852][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15 DHCPOFFER of 192.168.1.104 from 192.168.1.1 DHCPREQUEST for 192.168.1.104 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.104 from 192.168.1.1 bound to 192.168.1.104 -- renewal in 37195 seconds. [ 32.502492][ T1151] NET: Registered protocol family 10 [ 32.508781][ T1151] Segment Routing with IPv6 done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1362 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1389 (klogd) . ok [....] Starting system message bus: dbus[ 35.945623][ T1419] random: dbus-daemon: uninitialized urandom read (12 bytes read) [ 35.967780][ T1419] random: dbus-daemon: uninitialized urandom read (12 bytes read) . ok [....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon[ 36.079762][ T1442] random: avahi-daemon: uninitialized urandom read (4 bytes read) . ok [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [....] Starting OpenBSD Secure Shell server: sshd[ 131.620097][ C0] random: crng init done [ 131.624222][ C0] random: 1 urandom warning(s) missed due to ratelimiting . ok Making sure that Logitech Media Server is not running first: No process in pidfile '/var/run/logitechmediaserver.pid' found running; none killed. Starting Logitech Media Server. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 10 Dell-M300 ttyS0 Dell-M300 login:
Marvell>> printenv baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ kernel2bootup=no usiversion=kacemini-1.5 console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 filesize=728c0 fileaddr=1200000 netmask=255.255.255.0 ipaddr=192.168.58.233 serverip=192.168.58.188 ethaddr=18:03:73:41:db:3e run_diag=yes bootargs_console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) bootcmd_ideload=ide reset; ext2load ide 0:1 0x100000 /uImage; ext2load ide 0:1 0x01100000 /uInitrd kernel_config=setenv mainlineLinux yes; setenv mtdparts mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env); setenv load_uimage_addr 0x800000; setenv load_initrd_addr 0x02100000 load_uimage=ext2load usb 0:1 $(load_uimage_addr) /boot/uImage load_initrd=ext2load usb 0:1 $(load_initrd_addr) /boot/uInitrd set_bootargs_usb=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $(mtdparts) earlyprintk=serial set_bootargs_sata=setenv bootargs console=ttyS0,115200 root=LABEL=sata_rootfs rootdelay=10 $(mtdparts) earlyprintk=serial arcNumber=11 bootargs=console=ttyS0,115200 root=LABEL=sata_rootfs rootdelay=10 earlyprintk=serial bootcmd_ide2=ide reset; ext2load ide 0:1 $(load_uimage_addr) /boot/uImage; ext2load ide 0:1 $(load_initrd_addr) /boot/uInitrd; bootm $(load_uimage_addr) bootcmd2=ide reset;ext2load ide 0:2 0x1200000 /uImage-kacemini-000-bak;bootm 0x1200000 bootcmd=run kernel_config; run set_bootargs_usb; run bootcmd_usb; run set_bootargs_sata; run bootcmd_ide load_uimage_ide=ext2load ide 0:1 $(load_uimage_addr) /boot/uImage load_initrd_ide=ext2load ide 0:1 $(load_initrd_addr) /boot/uInitrd bootcmd_ide=echo Booting IDE .; ide reset; run load_uimage_ide; run load_initrd_ide; bootm $(load_uimage_addr) $(load_initrd_addr) load_uimage_usb=ext2load usb 0:1 $(load_uimage_addr) /boot/uImage load_initrd_usb=ext2load usb 0:1 $(load_initrd_addr) /boot/uInitrd bootcmd_usb=echo Booting USB.; usb reset; run load_uimage_usb; run load_initrd_usb; bootm $(load_uimage_addr) $(load_initrd_addr) stdin=serial stdout=serial stderr=serial mainlineLinux=yes enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no Environment size: 2873/4092 bytes
Re: Debian on Dell Kace M300 September 22, 2019 07:21PM |
Registered: 7 years ago Posts: 375 |
Re: Debian on Dell Kace M300 September 22, 2019 07:21PM |
Admin Registered: 13 years ago Posts: 19,102 |
Re: Debian on Dell Kace M300 September 22, 2019 07:34PM |
Registered: 11 years ago Posts: 155 |
Re: Debian on Dell Kace M300 September 22, 2019 07:56PM |
Admin Registered: 13 years ago Posts: 19,102 |
Re: Debian on Dell Kace M300 September 22, 2019 08:04PM |
Registered: 7 years ago Posts: 375 |
Re: Debian on Dell Kace M300 September 23, 2019 03:51AM |
Registered: 10 years ago Posts: 226 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Jun 20 2011 - 13:16:26) Marvell version: 3.4.27 USISH-SMB Ver: kacemini-1.5 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CDBC0 Soc: MV88F1155 Rev 1 (DDR3) CPU running @ 2000Mhz L2 running @ 500Mhz SysClock = 500Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7 DRAM CS[0] base 0x00000000 size 512MB DRAM CS[1] base 0x20000000 size 512MB DRAM CS[2] base 0x40000000 size 512MB DRAM CS[3] base 0x60000000 size 512MB DRAM Total size 2GB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done [512kB@f8000000] Flash: 512 kB Good CRC! CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Running diagnostics ... DDR3 data bus test PASSED DDR3 address bus test PASSED DDR3 device test PASSED Diag completed Hit any key to stop autoboot: 0 Booting USB. (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - usb 0:1 ** Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - usb 0:1 ** baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ kernel2bootup=no usiversion=kacemini-1.5 console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 netmask=255.255.255.0 ipaddr=192.168.58.233 ethaddr=18:03:73:41:db:40 run_diag=yes bootargs_console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) bootcmd_ideload=ide reset; ext2load ide 0:1 0x100000 /uImage; ext2load ide 0:1 0x01100000 /uInitrd bootcmd2=ide reset; ext2load ide 0:2 0x100000 /kbox/bin/uImage.bak; ext2load ide 0:1 0x01100000 /uInitrd;bootm 0x100000 0x01100000 kernel_config=setenv mainlineLinux yes; setenv mtdparts mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env); setenv load_uimage_addr 0x800000; setenv load_initrd_addr 0x02100000 load_uimage=ext2load usb 0:1 $(load_uimage_addr) /boot/uImage load_initrd=ext2load usb 0:1 $(load_initrd_addr) /boot/uInitrd set_bootargs_stock=setenv mainlineLinux no; setenv bootargs_console console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) root=LABEL=root rw bootcmd_stock=echo Booting stock ...; run bootcmd_ide set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $(mtdparts) earlyprintk=serial bootcmd_exec=echo Booting Debian .; usb start; run load_uimage; run load_initrd; bootm $(load_uimage_addr) $(load_initrd_addr) set_bootargs_usb=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $(mtdparts) earlyprintk=serial set_bootargs_sata=setenv bootargs console=ttyS0,115200 root=LABEL=sata_rootfs rootdelay=10 $(mtdparts) earlyprintk=serial bootcmd=run kernel_config; run set_bootargs_usb; run bootcmd_usb; run set_bootargs_sata; run bootcmd_ide serverip=192.168.0.100 serverport=614 load_uimage_usb=ext2load usb 0:1 $(load_uimage_addr) /boot/uImage load_initrd_usb=ext2load usb 0:1 $(load_initrd_addr) /boot/uInitrd bootcmd_usb=echo Booting USB.; usb reset; run load_uimage_usb; run load_initrd_usb; printenv; bootm $(load_uimage_addr) $(load_initrd_addr) bootcmd_ide=echo Booting IDE .; ide reset; run load_uimage_ide; run load_initrd_ide; printenv; bootm $(load_uimage_addr) $(load_initrd_addr) load_initrd_ide=ext2load ide 0:1 $(load_initrd_addr) /boot/uInitrd load_uimage_ide=ext2load ide 0:1 $(load_uimage_addr) /boot/uImage stdin=serial stdout=serial stderr=serial enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no mainlineLinux=yes mtdparts=mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) load_uimage_addr=0x800000 load_initrd_addr=0x02100000 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) earlyprintk=serial Environment size: 3395/4092 bytes ## Booting image at 00800000 ... Bad Magic Number Booting IDE . Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: TS16GSSD25H-M Firm: 20100712 Ser#: 20110423421602036149 Type: Hard Disk Supports 48-bit addressing Capacity: 15272.0 MB = 14.9 GB (31277056 x 512) [0 0] sata unrecoverable error occured, restart channel USI board reset ø __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Jun 20 2011 - 13:16:26) Marvell version: 3.4.27 USISH-SMB Ver: kacemini-1.5 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CDBC0 Soc: MV88F1155 Rev 1 (DDR3) CPU running @ 2000Mhz L2 running @ 500Mhz SysClock = 500Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7 DRAM CS[0] base 0x00000000 size 512MB DRAM CS[1] base 0x20000000 size 512MB DRAM CS[2] base 0x40000000 size 512MB DRAM CS[3] base 0x60000000 size 512MB DRAM Total size 2GB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done [512kB@f8000000] Flash: 512 kB Good CRC! CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Running diagnostics ... DDR3 data bus test PASSED DDR3 address bus test PASSED DDR3 device test PASSED Diag completed Hit any key to stop autoboot: 0 Booting USB. (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - usb 0:1 ** Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - usb 0:1 ** baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ kernel2bootup=no usiversion=kacemini-1.5 console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 netmask=255.255.255.0 ipaddr=192.168.58.233 ethaddr=18:03:73:41:db:40 run_diag=yes bootargs_console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) bootcmd_ideload=ide reset; ext2load ide 0:1 0x100000 /uImage; ext2load ide 0:1 0x01100000 /uInitrd bootcmd2=ide reset; ext2load ide 0:2 0x100000 /kbox/bin/uImage.bak; ext2load ide 0:1 0x01100000 /uInitrd;bootm 0x100000 0x01100000 kernel_config=setenv mainlineLinux yes; setenv mtdparts mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env); setenv load_uimage_addr 0x800000; setenv load_initrd_addr 0x02100000 load_uimage=ext2load usb 0:1 $(load_uimage_addr) /boot/uImage load_initrd=ext2load usb 0:1 $(load_initrd_addr) /boot/uInitrd set_bootargs_stock=setenv mainlineLinux no; setenv bootargs_console console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) root=LABEL=root rw bootcmd_stock=echo Booting stock ...; run bootcmd_ide set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $(mtdparts) earlyprintk=serial bootcmd_exec=echo Booting Debian .; usb start; run load_uimage; run load_initrd; bootm $(load_uimage_addr) $(load_initrd_addr) set_bootargs_usb=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $(mtdparts) earlyprintk=serial set_bootargs_sata=setenv bootargs console=ttyS0,115200 root=LABEL=sata_rootfs rootdelay=10 $(mtdparts) earlyprintk=serial bootcmd=run kernel_config; run set_bootargs_usb; run bootcmd_usb; run set_bootargs_sata; run bootcmd_ide serverip=192.168.0.100 serverport=614 load_uimage_usb=ext2load usb 0:1 $(load_uimage_addr) /boot/uImage load_initrd_usb=ext2load usb 0:1 $(load_initrd_addr) /boot/uInitrd bootcmd_usb=echo Booting USB.; usb reset; run load_uimage_usb; run load_initrd_usb; printenv; bootm $(load_uimage_addr) $(load_initrd_addr) bootcmd_ide=echo Booting IDE .; ide reset; run load_uimage_ide; run load_initrd_ide; printenv; bootm $(load_uimage_addr) $(load_initrd_addr) load_initrd_ide=ext2load ide 0:1 $(load_initrd_addr) /boot/uInitrd load_uimage_ide=ext2load ide 0:1 $(load_uimage_addr) /boot/uImage stdin=serial stdout=serial stderr=serial enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no mainlineLinux=yes mtdparts=mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) load_uimage_addr=0x800000 load_initrd_addr=0x02100000 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) earlyprintk=serial Environment size: 3395/4092 bytes ## Booting image at 00800000 ... Bad Magic Number Booting IDE . Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: TS16GSSD25H-M Firm: 20100712 Ser#: 20110423421602036149 Type: Hard Disk Supports 48-bit addressing Capacity: 15272.0 MB = 14.9 GB (31277056 x 512) 4981772 bytes read 9784778 bytes read baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ kernel2bootup=no usiversion=kacemini-1.5 console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 netmask=255.255.255.0 ipaddr=192.168.58.233 ethaddr=18:03:73:41:db:40 run_diag=yes bootargs_console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) bootcmd_ideload=ide reset; ext2load ide 0:1 0x100000 /uImage; ext2load ide 0:1 0x01100000 /uInitrd bootcmd2=ide reset; ext2load ide 0:2 0x100000 /kbox/bin/uImage.bak; ext2load ide 0:1 0x01100000 /uInitrd;bootm 0x100000 0x01100000 kernel_config=setenv mainlineLinux yes; setenv mtdparts mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env); setenv load_uimage_addr 0x800000; setenv load_initrd_addr 0x02100000 load_uimage=ext2load usb 0:1 $(load_uimage_addr) /boot/uImage load_initrd=ext2load usb 0:1 $(load_initrd_addr) /boot/uInitrd set_bootargs_stock=setenv mainlineLinux no; setenv bootargs_console console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) root=LABEL=root rw bootcmd_stock=echo Booting stock ...; run bootcmd_ide set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $(mtdparts) earlyprintk=serial bootcmd_exec=echo Booting Debian .; usb start; run load_uimage; run load_initrd; bootm $(load_uimage_addr) $(load_initrd_addr) set_bootargs_usb=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $(mtdparts) earlyprintk=serial set_bootargs_sata=setenv bootargs console=ttyS0,115200 root=LABEL=sata_rootfs rootdelay=10 $(mtdparts) earlyprintk=serial bootcmd=run kernel_config; run set_bootargs_usb; run bootcmd_usb; run set_bootargs_sata; run bootcmd_ide serverip=192.168.0.100 serverport=614 load_uimage_usb=ext2load usb 0:1 $(load_uimage_addr) /boot/uImage load_initrd_usb=ext2load usb 0:1 $(load_initrd_addr) /boot/uInitrd bootcmd_usb=echo Booting USB.; usb reset; run load_uimage_usb; run load_initrd_usb; printenv; bootm $(load_uimage_addr) $(load_initrd_addr) bootcmd_ide=echo Booting IDE .; ide reset; run load_uimage_ide; run load_initrd_ide; printenv; bootm $(load_uimage_addr) $(load_initrd_addr) load_initrd_ide=ext2load ide 0:1 $(load_initrd_addr) /boot/uInitrd load_uimage_ide=ext2load ide 0:1 $(load_uimage_addr) /boot/uImage stdin=serial stdout=serial stderr=serial enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no mainlineLinux=yes mtdparts=mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) load_uimage_addr=0x800000 load_initrd_addr=0x02100000 bootargs=console=ttyS0,115200 root=LABEL=sata_rootfs rootdelay=10 mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) earlyprintk=serial filesize=954DCA Environment size: 3416/4092 bytes ## Booting image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-2 Created: 2019-09-18 8:31:06 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4981708 Bytes = 4.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initramfs-5.2.9-kirkwood-tld-2 Created: 2019-09-21 10:27:48 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9784714 Bytes = 9.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.2.9-kirkwood-tld-2 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Wed Aug 28 03:55:21 PDT 2019 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Dell KACE M300 [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Ignoring RAM at 0x70000000-0x80000000 [ 0.000000][ T0] Consider using a HIGHMEM enabled kernel. [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 455168 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=sata_rootfs rootdelay=10 mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) earlyprintk=serial [ 0.000000][ T0] Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes) [ 0.000000][ T0] Inode-cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000][ T0] Memory: 1793952K/1835008K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 300K bss, 41056K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x52c/0x924 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000006][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008509][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.015622][ T0] Console: colour dummy device 80x30 [ 0.020802][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032004][ T0] pid_max: default: 32768 minimum: 301 [ 0.037554][ T0] LSM: Security Framework initializing [ 0.043013][ T0] Mount-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.050429][ T0] Mountpoint-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.058878][ T0] *** VALIDATE proc *** [ 0.063070][ T0] *** VALIDATE cgroup1 *** [ 0.067325][ T0] *** VALIDATE cgroup2 *** [ 0.071674][ T0] CPU: Testing write buffer coherency: ok [ 0.078509][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.085576][ T1] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1 [ 0.091632][ T1] rcu: Hierarchical SRCU implementation. [ 0.099347][ T1] devtmpfs: initialized [ 0.107030][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.117571][ T1] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.124580][ T1] xor: measuring software checksum speed [ 0.228527][ T1] arm4regs : 1816.800 MB/sec [ 0.328530][ T1] 8regs : 1090.400 MB/sec [ 0.428527][ T1] 32regs : 1585.600 MB/sec [ 0.433383][ T1] xor: using function: arm4regs (1816.800 MB/sec) [ 0.439650][ T1] prandom: seed boundary self test passed [ 0.447698][ T1] prandom: 100 self tests passed [ 0.452494][ T1] pinctrl core: initialized pinctrl subsystem [ 0.459520][ T1] NET: Registered protocol family 16 [ 0.465030][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.473232][ T1] audit: initializing netlink subsys (disabled) [ 0.480296][ T14] audit: type=2000 audit(0.470:1): state=initialized audit_enabled=0 res=1 [ 0.488809][ T1] cpuidle: using governor ladder [ 0.493637][ T1] cpuidle: using governor menu [ 0.498646][ T1] Feroceon L2: Enabling L2 [ 0.502918][ T1] Feroceon L2: Cache support initialised. [ 0.512293][ T1] No ATAGs? [ 2.568514][ C0] random: fast init done [ 3.736898][ T71] alg: No test for lzo-rle (lzo-rle-generic) [ 3.743051][ T73] alg: No test for lzo-rle (lzo-rle-scomp) [ 3.918823][ T1] raid6: int32x8 gen() 208 MB/s [ 4.088873][ T1] raid6: int32x8 xor() 142 MB/s [ 4.258615][ T1] raid6: int32x4 gen() 208 MB/s [ 4.428662][ T1] raid6: int32x4 xor() 138 MB/s [ 4.598617][ T1] raid6: int32x2 gen() 210 MB/s [ 4.768669][ T1] raid6: int32x2 xor() 152 MB/s [ 4.938706][ T1] raid6: int32x1 gen() 157 MB/s [ 5.108551][ T1] raid6: int32x1 xor() 109 MB/s [ 5.113485][ T1] raid6: using algorithm int32x2 gen() 210 MB/s [ 5.119553][ T1] raid6: .... xor() 152 MB/s, rmw enabled [ 5.125097][ T1] raid6: using intx1 recovery algorithm [ 5.130658][ T1] vgaarb: loaded [ 5.134383][ T1] SCSI subsystem initialized [ 5.139186][ T1] usbcore: registered new interface driver usbfs [ 5.145367][ T1] usbcore: registered new interface driver hub [ 5.151424][ T1] usbcore: registered new device driver usb [ 5.157267][ T1] pps_core: LinuxPPS API ver. 1 registered [ 5.162914][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 5.172711][ T1] PTP clock support registered [ 5.178249][ T1] clocksource: Switched to clocksource orion_clocksource [ 5.790888][ T1] VFS: Disk quotas dquot_6.6.0 [ 5.795547][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 5.809890][ T1] NET: Registered protocol family 2 [ 5.815494][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 1, 8192 bytes) [ 5.823986][ T1] TCP established hash table entries: 16384 (order: 4, 65536 bytes) [ 5.831999][ T1] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 5.839401][ T1] TCP: Hash tables configured (established 16384 bind 16384) [ 5.846667][ T1] UDP hash table entries: 1024 (order: 2, 16384 bytes) [ 5.853398][ T1] UDP-Lite hash table entries: 1024 (order: 2, 16384 bytes) [ 5.860708][ T1] NET: Registered protocol family 1 [ 5.866206][ T1] RPC: Registered named UNIX socket transport module. [ 5.872848][ T1] RPC: Registered udp transport module. [ 5.878220][ T1] RPC: Registered tcp transport module. [ 5.883602][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 5.890714][ T1] PCI: CLS 0 bytes, default 32 [ 5.895466][ T1] Trying to unpack rootfs image as initramfs... [ 6.437697][ T1] Freeing initrd memory: 9556K [ 6.442451][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 6.450546][ T1] Initialise system trusted keyrings [ 6.455691][ T1] Key type blacklist registered [ 6.460582][ T1] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 6.467738][ T1] zbud: loaded [ 6.471784][ T1] NFS: Registering the id_resolver key type [ 6.477513][ T1] Key type id_resolver registered [ 6.482427][ T1] Key type id_legacy registered [ 6.487118][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 6.494500][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 6.501755][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 6.509630][ T1] fuse: init (API version 7.31) [ 6.514571][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 6.521815][ T1] orangefs_init: module version upstream loaded [ 6.527879][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 6.548064][ T1] async_tx: api initialized (async) [ 6.553168][ T1] Key type asymmetric registered [ 6.557930][ T1] Asymmetric key parser 'x509' registered [ 6.563552][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 6.572649][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.581995][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 6.590280][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 6.596433][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 6.603985][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 6.610990][ T1] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400 [ 6.617677][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 6.625813][ T1] PCI: bus0: Fast back to back transfers disabled [ 6.632077][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 6.641424][ T1] PCI: bus1: Fast back to back transfers enabled [ 6.647580][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 6.654984][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref] [ 6.662885][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 6.668925][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.728798][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 6.738039][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.798763][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 6.808194][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.816132][ T1] printk: console [ttyS0] disabled [ 6.821167][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 6.830839][ T1] printk: console [ttyS0] enabled [ 6.830839][ T1] printk: console [ttyS0] enabled [ 6.840659][ T1] printk: bootconsole [earlycon0] disabled [ 6.840659][ T1] printk: bootconsole [earlycon0] disabled [ 6.857301][ T1] loop: module loaded [ 6.861611][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 6.869139][ T1] scsi host0: sata_mv [ 6.873420][ T1] scsi host1: sata_mv [ 6.877464][ T1] ata1: SATA max UDMA/133 irq 33 [ 6.882322][ T1] ata2: SATA max UDMA/133 irq 33 [ 6.888375][ T1] m25p80 spi0.0: mx25l4005a (512 Kbytes) [ 6.893901][ T1] 2 cmdlinepart partitions found on MTD device spi0.0 [ 6.900577][ T1] Creating 2 MTD partitions on "spi0.0": [ 6.906092][ T1] 0x000000000000-0x00000007f000 : "uboot" [ 6.912620][ T1] 0x00000007f000-0x000000080000 : "u-boot-env" [ 6.920303][ T1] libphy: Fixed MDIO Bus: probed [ 6.925652][ T1] libphy: orion_mdio_bus: probed [ 6.940216][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 6.948059][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 6.955987][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 18:03:73:41:db:40 [ 6.965577][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.972926][ T1] ehci-pci: EHCI PCI platform driver [ 6.978134][ T1] ehci-orion: EHCI orion driver [ 6.983029][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 6.989300][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 6.997802][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 7.028275][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 7.035192][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 7.044209][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.052172][ T1] usb usb1: Product: EHCI Host Controller [ 7.057764][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-2 ehci_hcd [ 7.065112][ T1] usb usb1: SerialNumber: f1050000.ehci [ 7.070965][ T1] hub 1-0:1.0: USB hub found [ 7.075458][ T1] hub 1-0:1.0: 1 port detected [ 7.080614][ T1] usbcore: registered new interface driver usb-storage [ 7.087598][ T1] mousedev: PS/2 mouse device common for all mice [ 7.094336][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 7.100070][ T1] i2c /dev entries driver [ 7.104712][ T1] device-mapper: uevent: version 1.0.3 [ 7.110308][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 7.119813][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 7.127102][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 7.134483][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 7.141913][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 7.148791][ T1] device-mapper: raid: Loading target version 1.14.0 [ 7.156133][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 7.162533][ T1] drop_monitor: Initializing network drop monitor service [ 7.169763][ T1] NET: Registered protocol family 17 [ 7.175134][ T1] Key type dns_resolver registered [ 7.180742][ T1] registered taskstats version 1 [ 7.185583][ T1] Loading compiled-in X.509 certificates [ 7.191272][ T1] zswap: loaded using pool lzo/zbud [ 7.259751][ T1] Key type big_key registered [ 7.292967][ T1] Key type encrypted registered [ 7.299418][ T1] rtc-mv f1010300.rtc: setting system clock to 2019-09-23T07:04:53 UTC (1569222293) [ 7.388285][ T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 7.399769][ T112] ata1.00: ATA-7: TS16GSSD25H-M, 20100712, max UDMA/133 [ 7.406591][ T112] ata1.00: 31277056 sectors, multi 0: LBA48 [ 7.419138][ T112] ata1.00: configured for UDMA/133 [ 7.434511][ T7] scsi 0:0:0:0: Direct-Access ATA TS16GSSD25H-M 0712 PQ: 0 ANSI: 5 [ 7.444135][ T116] sd 0:0:0:0: [sda] 31277056 512-byte logical blocks: (16.0 GB/14.9 GiB) [ 7.452474][ T15] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 7.460361][ T116] sd 0:0:0:0: [sda] Write Protect is off [ 7.466049][ T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.477310][ T116] sda: sda1 [ 7.481549][ T116] sd 0:0:0:0: [sda] Attached SCSI disk [ 7.658685][ T15] usb 1-1: New USB device found, idVendor=058f, idProduct=6254, bcdDevice= 1.00 [ 7.667609][ T15] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 7.675913][ T15] hub 1-1:1.0: USB hub found [ 7.680555][ T15] hub 1-1:1.0: 4 ports detected [ 7.791779][ T114] ata2: SATA link down (SStatus 0 SControl F300) [ 7.811244][ T1] Freeing unused kernel memory: 1024K [ 7.816875][ T1] Checked W+X mappings: passed, no W+X pages found [ 7.823280][ T1] Run /init as init process Loading, please wait... Starting version 241 [ 7.998334][ T15] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 8.175705][ T15] usb 1-1.2: New USB device found, idVendor=058f, idProduct=6387, bcdDevice= 1.05 [ 8.201082][ T15] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 8.223708][ T15] usb 1-1.2: Product: Mass Storage [ 8.243729][ T15] usb 1-1.2: Manufacturer: Generic [ 8.253642][ T15] usb 1-1.2: SerialNumber: 2597E11A [ 8.274358][ T15] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 8.302666][ T15] scsi host2: usb-storage 1-1.2:1.0 [ 8.418740][ T175] usbcore: registered new interface driver uas [ 8.446409][ T173] input: gpio_keys as /devices/platform/gpio_keys/input/input0 Begin: Loading essential drivers ... done. [ 9.380384][ T116] scsi 2:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ: 0 ANSI: 4 [ 9.394107][ T23] sd 2:0:0:0: [sdb] 7987200 512-byte logical blocks: (4.09 GB/3.81 GiB) [ 9.407095][ T23] sd 2:0:0:0: [sdb] Write Protect is off [ 9.413578][ T23] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 9.429798][ T23] sdb: sdb1 [ 9.441471][ T23] sd 2:0:0:0: [sdb] Attached SCSI removable disk Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.33.1 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 sata_rootfs: clean, 20025/979200 files, 297289/3909376 blocks done. [ 18.950787][ T197] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 18.968727][ T197] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Starting hotplug events dispatcher: systemd-udevd. [ ok ] Synthesizing the initial hotplug events (subsystems)...done. [....] Synthesizing the initial hotplug events (devices)...[ 20.554124][ T400] systemd-udevd[400]: Using default interface naming scheme 'v240'. [ ok done. [....] Waiting for /dev to be fully populated...[ 20.680838][ T400] systemd-udevd[400]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 20.819682][ T395] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range [ 20.953929][ T395] watchdog: f1020300.watchdog-timer: falling back to default timeout (21) [ 21.017670][ T397] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 21.070397][ T395] orion_wdt: Initial timeout 21 sec [ 21.116988][ T379] marvell-cesa f1030000.crypto: CESA device successfully registered [ 21.125074][ T397] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 21.224693][ T377] systemd-udevd[377]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. done. [ ok ] Setting hostname to 'kaceM300-1'...done. [ ok ] Activating swap:. [ 22.170036][ T598] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [info] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=sata_rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs[ ok hat location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Starting Setting kernel variables: sysctl. [....] Initializing random number generator...[ 23.976021][ T1072] random: dd: uninitialized urandom read (512 bytes read) done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/18:03:73:41:db:40 Sending on LPF/eth0/18:03:73:41:db:40 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 [ 25.923374][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPOFFER of 192.168.0.117 from 192.168.0.1 DHCPREQUEST for 192.168.0.117 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.0.117 from 192.168.0.1 bound to 192.168.0.117 -- renewal in 17475 seconds. [ 30.463564][ T1152] NET: Registered protocol family 10 [ 30.469873][ T1152] Segment Routing with IPv6 done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1363 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1390 (klogd) . ok [....] Starting system message bus: dbus[ 33.947694][ T1420] random: dbus-daemon: uninitialized urandom read (12 bytes read) [ 33.971070][ T1420] random: dbus-daemon: uninitialized urandom read (12 bytes read) . ok [....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon[ 34.087061][ T1443] random: avahi-daemon: uninitialized urandom read (4 bytes read) . ok [ ok ] Starting entropy daemon: haveged. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [....] Starting OpenBSD Secure Shell server: sshd[ 36.428336][ T1472] random: crng init done [ 36.432681][ T1472] random: 1 urandom warning(s) missed due to ratelimiting . ok [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 10 kaceM300-1 ttyS0 kaceM300-1 login:
Re: Debian on Dell Kace M300 September 23, 2019 03:52AM |
Registered: 10 years ago Posts: 226 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Jun 20 2011 - 13:16:26) Marvell version: 3.4.27 USISH-SMB Ver: kacemini-1.5 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CDBC0 Soc: MV88F1155 Rev 1 (DDR3) CPU running @ 2000Mhz L2 running @ 500Mhz SysClock = 500Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7 DRAM CS[0] base 0x00000000 size 512MB DRAM CS[1] base 0x20000000 size 512MB DRAM CS[2] base 0x40000000 size 512MB DRAM CS[3] base 0x60000000 size 512MB DRAM Total size 2GB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done [512kB@f8000000] Flash: 512 kB Good CRC! CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Running diagnostics ... DDR3 data bus test PASSED DDR3 address bus test PASSED DDR3 device test PASSED Diag completed Hit any key to stop autoboot: 0 Booting USB. (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found Waiting for storage device(s) to settle before scanning... 0 Storage Device(s) found ** Bad partition 1 ** ** Bad partition 1 ** baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ kernel2bootup=no usiversion=kacemini-1.5 console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 netmask=255.255.255.0 ipaddr=192.168.58.233 ethaddr=18:03:73:41:db:40 run_diag=yes bootargs_console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) bootcmd_ideload=ide reset; ext2load ide 0:1 0x100000 /uImage; ext2load ide 0:1 0x01100000 /uInitrd bootcmd2=ide reset; ext2load ide 0:2 0x100000 /kbox/bin/uImage.bak; ext2load ide 0:1 0x01100000 /uInitrd;bootm 0x100000 0x01100000 kernel_config=setenv mainlineLinux yes; setenv mtdparts mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env); setenv load_uimage_addr 0x800000; setenv load_initrd_addr 0x02100000 load_uimage=ext2load usb 0:1 $(load_uimage_addr) /boot/uImage load_initrd=ext2load usb 0:1 $(load_initrd_addr) /boot/uInitrd set_bootargs_stock=setenv mainlineLinux no; setenv bootargs_console console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) root=LABEL=root rw bootcmd_stock=echo Booting stock ...; run bootcmd_ide set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $(mtdparts) earlyprintk=serial bootcmd_exec=echo Booting Debian .; usb start; run load_uimage; run load_initrd; bootm $(load_uimage_addr) $(load_initrd_addr) set_bootargs_usb=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $(mtdparts) earlyprintk=serial set_bootargs_sata=setenv bootargs console=ttyS0,115200 root=LABEL=sata_rootfs rootdelay=10 $(mtdparts) earlyprintk=serial bootcmd=run kernel_config; run set_bootargs_usb; run bootcmd_usb; run set_bootargs_sata; run bootcmd_ide serverip=192.168.0.100 serverport=614 load_uimage_usb=ext2load usb 0:1 $(load_uimage_addr) /boot/uImage load_initrd_usb=ext2load usb 0:1 $(load_initrd_addr) /boot/uInitrd bootcmd_usb=echo Booting USB.; usb reset; run load_uimage_usb; run load_initrd_usb; printenv; bootm $(load_uimage_addr) $(load_initrd_addr) bootcmd_ide=echo Booting IDE .; ide reset; run load_uimage_ide; run load_initrd_ide; printenv; bootm $(load_uimage_addr) $(load_initrd_addr) load_initrd_ide=ext2load ide 0:1 $(load_initrd_addr) /boot/uInitrd load_uimage_ide=ext2load ide 0:1 $(load_uimage_addr) /boot/uImage stdin=serial stdout=serial stderr=serial enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no mainlineLinux=yes mtdparts=mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) load_uimage_addr=0x800000 load_initrd_addr=0x02100000 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) earlyprintk=serial Environment size: 3395/4092 bytes ## Booting image at 00800000 ... Bad Magic Number Booting IDE . Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: TS16GSSD25H-M Firm: 20100712 Ser#: 20110423421602036149 Type: Hard Disk Supports 48-bit addressing Capacity: 15272.0 MB = 14.9 GB (31277056 x 512) 4981772 bytes read 9784778 bytes read baudrate=115200 loads_echo=0 rootpath=/mnt/ARM_FS/ kernel2bootup=no usiversion=kacemini-1.5 console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no ethact=egiga0 netmask=255.255.255.0 ipaddr=192.168.58.233 ethaddr=18:03:73:41:db:40 run_diag=yes bootargs_console=console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) bootcmd_ideload=ide reset; ext2load ide 0:1 0x100000 /uImage; ext2load ide 0:1 0x01100000 /uInitrd bootcmd2=ide reset; ext2load ide 0:2 0x100000 /kbox/bin/uImage.bak; ext2load ide 0:1 0x01100000 /uInitrd;bootm 0x100000 0x01100000 kernel_config=setenv mainlineLinux yes; setenv mtdparts mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env); setenv load_uimage_addr 0x800000; setenv load_initrd_addr 0x02100000 load_uimage=ext2load usb 0:1 $(load_uimage_addr) /boot/uImage load_initrd=ext2load usb 0:1 $(load_initrd_addr) /boot/uInitrd set_bootargs_stock=setenv mainlineLinux no; setenv bootargs_console console=ttyS0,115200 mtdparts=spi_flash:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) root=LABEL=root rw bootcmd_stock=echo Booting stock ...; run bootcmd_ide set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $(mtdparts) earlyprintk=serial bootcmd_exec=echo Booting Debian .; usb start; run load_uimage; run load_initrd; bootm $(load_uimage_addr) $(load_initrd_addr) set_bootargs_usb=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $(mtdparts) earlyprintk=serial set_bootargs_sata=setenv bootargs console=ttyS0,115200 root=LABEL=sata_rootfs rootdelay=10 $(mtdparts) earlyprintk=serial bootcmd=run kernel_config; run set_bootargs_usb; run bootcmd_usb; run set_bootargs_sata; run bootcmd_ide serverip=192.168.0.100 serverport=614 load_uimage_usb=ext2load usb 0:1 $(load_uimage_addr) /boot/uImage load_initrd_usb=ext2load usb 0:1 $(load_initrd_addr) /boot/uInitrd bootcmd_usb=echo Booting USB.; usb reset; run load_uimage_usb; run load_initrd_usb; printenv; bootm $(load_uimage_addr) $(load_initrd_addr) bootcmd_ide=echo Booting IDE .; ide reset; run load_uimage_ide; run load_initrd_ide; printenv; bootm $(load_uimage_addr) $(load_initrd_addr) load_initrd_ide=ext2load ide 0:1 $(load_initrd_addr) /boot/uInitrd load_uimage_ide=ext2load ide 0:1 $(load_uimage_addr) /boot/uImage stdin=serial stdout=serial stderr=serial enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no mainlineLinux=yes mtdparts=mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) load_uimage_addr=0x800000 load_initrd_addr=0x02100000 bootargs=console=ttyS0,115200 root=LABEL=sata_rootfs rootdelay=10 mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) earlyprintk=serial filesize=954DCA Environment size: 3416/4092 bytes ## Booting image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-2 Created: 2019-09-18 8:31:06 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4981708 Bytes = 4.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initramfs-5.2.9-kirkwood-tld-2 Created: 2019-09-21 10:27:48 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9784714 Bytes = 9.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.2.9-kirkwood-tld-2 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Wed Aug 28 03:55:21 PDT 2019 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Dell KACE M300 [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Ignoring RAM at 0x70000000-0x80000000 [ 0.000000][ T0] Consider using a HIGHMEM enabled kernel. [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 455168 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=sata_rootfs rootdelay=10 mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) earlyprintk=serial [ 0.000000][ T0] Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes) [ 0.000000][ T0] Inode-cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000][ T0] Memory: 1793952K/1835008K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 300K bss, 41056K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x52c/0x924 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000006][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008509][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.015620][ T0] Console: colour dummy device 80x30 [ 0.020802][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032004][ T0] pid_max: default: 32768 minimum: 301 [ 0.037556][ T0] LSM: Security Framework initializing [ 0.043013][ T0] Mount-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.050428][ T0] Mountpoint-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.058878][ T0] *** VALIDATE proc *** [ 0.063068][ T0] *** VALIDATE cgroup1 *** [ 0.067325][ T0] *** VALIDATE cgroup2 *** [ 0.071674][ T0] CPU: Testing write buffer coherency: ok [ 0.078508][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.085567][ T1] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1 [ 0.091623][ T1] rcu: Hierarchical SRCU implementation. [ 0.099336][ T1] devtmpfs: initialized [ 0.107037][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.117579][ T1] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.124588][ T1] xor: measuring software checksum speed [ 0.228530][ T1] arm4regs : 1816.800 MB/sec [ 0.328529][ T1] 8regs : 1090.400 MB/sec [ 0.428529][ T1] 32regs : 1585.600 MB/sec [ 0.433391][ T1] xor: using function: arm4regs (1816.800 MB/sec) [ 0.439659][ T1] prandom: seed boundary self test passed [ 0.447706][ T1] prandom: 100 self tests passed [ 0.452504][ T1] pinctrl core: initialized pinctrl subsystem [ 0.459528][ T1] NET: Registered protocol family 16 [ 0.465039][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.473242][ T1] audit: initializing netlink subsys (disabled) [ 0.480295][ T14] audit: type=2000 audit(0.470:1): state=initialized audit_enabled=0 res=1 [ 0.488804][ T1] cpuidle: using governor ladder [ 0.493628][ T1] cpuidle: using governor menu [ 0.498638][ T1] Feroceon L2: Enabling L2 [ 0.502909][ T1] Feroceon L2: Cache support initialised. [ 0.512285][ T1] No ATAGs? [ 2.568513][ C0] random: fast init done [ 3.736895][ T71] alg: No test for lzo-rle (lzo-rle-generic) [ 3.743041][ T73] alg: No test for lzo-rle (lzo-rle-scomp) [ 3.918814][ T1] raid6: int32x8 gen() 208 MB/s [ 4.088870][ T1] raid6: int32x8 xor() 142 MB/s [ 4.258562][ T1] raid6: int32x4 gen() 208 MB/s [ 4.428663][ T1] raid6: int32x4 xor() 138 MB/s [ 4.598578][ T1] raid6: int32x2 gen() 210 MB/s [ 4.768667][ T1] raid6: int32x2 xor() 152 MB/s [ 4.938707][ T1] raid6: int32x1 gen() 157 MB/s [ 5.108552][ T1] raid6: int32x1 xor() 109 MB/s [ 5.113486][ T1] raid6: using algorithm int32x2 gen() 210 MB/s [ 5.119552][ T1] raid6: .... xor() 152 MB/s, rmw enabled [ 5.125097][ T1] raid6: using intx1 recovery algorithm [ 5.130658][ T1] vgaarb: loaded [ 5.134385][ T1] SCSI subsystem initialized [ 5.139190][ T1] usbcore: registered new interface driver usbfs [ 5.145377][ T1] usbcore: registered new interface driver hub [ 5.151431][ T1] usbcore: registered new device driver usb [ 5.157265][ T1] pps_core: LinuxPPS API ver. 1 registered [ 5.162914][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 5.172711][ T1] PTP clock support registered [ 5.178247][ T1] clocksource: Switched to clocksource orion_clocksource [ 5.790880][ T1] VFS: Disk quotas dquot_6.6.0 [ 5.795539][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 5.809880][ T1] NET: Registered protocol family 2 [ 5.815482][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 1, 8192 bytes) [ 5.823969][ T1] TCP established hash table entries: 16384 (order: 4, 65536 bytes) [ 5.831982][ T1] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 5.839384][ T1] TCP: Hash tables configured (established 16384 bind 16384) [ 5.846649][ T1] UDP hash table entries: 1024 (order: 2, 16384 bytes) [ 5.853380][ T1] UDP-Lite hash table entries: 1024 (order: 2, 16384 bytes) [ 5.860695][ T1] NET: Registered protocol family 1 [ 5.866187][ T1] RPC: Registered named UNIX socket transport module. [ 5.872828][ T1] RPC: Registered udp transport module. [ 5.878194][ T1] RPC: Registered tcp transport module. [ 5.883577][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 5.890688][ T1] PCI: CLS 0 bytes, default 32 [ 5.895442][ T1] Trying to unpack rootfs image as initramfs... [ 6.437667][ T1] Freeing initrd memory: 9556K [ 6.442426][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 6.450517][ T1] Initialise system trusted keyrings [ 6.455668][ T1] Key type blacklist registered [ 6.460565][ T1] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 6.467719][ T1] zbud: loaded [ 6.471757][ T1] NFS: Registering the id_resolver key type [ 6.477488][ T1] Key type id_resolver registered [ 6.482401][ T1] Key type id_legacy registered [ 6.487091][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 6.494464][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 6.501721][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 6.509596][ T1] fuse: init (API version 7.31) [ 6.514542][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 6.521790][ T1] orangefs_init: module version upstream loaded [ 6.527854][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 6.548044][ T1] async_tx: api initialized (async) [ 6.553150][ T1] Key type asymmetric registered [ 6.557912][ T1] Asymmetric key parser 'x509' registered [ 6.563533][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 6.572637][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.581989][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 6.590272][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 6.596424][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 6.603978][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 6.610983][ T1] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400 [ 6.617668][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 6.625801][ T1] PCI: bus0: Fast back to back transfers disabled [ 6.632069][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 6.641413][ T1] PCI: bus1: Fast back to back transfers enabled [ 6.647571][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 6.654985][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref] [ 6.662885][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 6.668926][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.728798][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 6.738047][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.798759][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 6.808180][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.816112][ T1] printk: console [ttyS0] disabled [ 6.821148][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 6.830821][ T1] printk: console [ttyS0] enabled [ 6.830821][ T1] printk: console [ttyS0] enabled [ 6.840643][ T1] printk: bootconsole [earlycon0] disabled [ 6.840643][ T1] printk: bootconsole [earlycon0] disabled [ 6.857275][ T1] loop: module loaded [ 6.861592][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 6.869120][ T1] scsi host0: sata_mv [ 6.873393][ T1] scsi host1: sata_mv [ 6.877438][ T1] ata1: SATA max UDMA/133 irq 33 [ 6.882297][ T1] ata2: SATA max UDMA/133 irq 33 [ 6.888351][ T1] m25p80 spi0.0: mx25l4005a (512 Kbytes) [ 6.893876][ T1] 2 cmdlinepart partitions found on MTD device spi0.0 [ 6.900551][ T1] Creating 2 MTD partitions on "spi0.0": [ 6.906067][ T1] 0x000000000000-0x00000007f000 : "uboot" [ 6.912596][ T1] 0x00000007f000-0x000000080000 : "u-boot-env" [ 6.920273][ T1] libphy: Fixed MDIO Bus: probed [ 6.925630][ T1] libphy: orion_mdio_bus: probed [ 6.940286][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 6.948129][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 6.956060][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 18:03:73:41:db:40 [ 6.965657][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.973004][ T1] ehci-pci: EHCI PCI platform driver [ 6.978204][ T1] ehci-orion: EHCI orion driver [ 6.983098][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 6.989369][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 6.997896][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 7.028272][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 7.035191][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 7.044209][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.052171][ T1] usb usb1: Product: EHCI Host Controller [ 7.057765][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-2 ehci_hcd [ 7.065120][ T1] usb usb1: SerialNumber: f1050000.ehci [ 7.070972][ T1] hub 1-0:1.0: USB hub found [ 7.075466][ T1] hub 1-0:1.0: 1 port detected [ 7.080623][ T1] usbcore: registered new interface driver usb-storage [ 7.087607][ T1] mousedev: PS/2 mouse device common for all mice [ 7.094342][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 7.100078][ T1] i2c /dev entries driver [ 7.104720][ T1] device-mapper: uevent: version 1.0.3 [ 7.110313][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 7.119818][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 7.127103][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 7.134492][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 7.141924][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 7.148798][ T1] device-mapper: raid: Loading target version 1.14.0 [ 7.156128][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 7.162527][ T1] drop_monitor: Initializing network drop monitor service [ 7.169754][ T1] NET: Registered protocol family 17 [ 7.175127][ T1] Key type dns_resolver registered [ 7.180738][ T1] registered taskstats version 1 [ 7.185573][ T1] Loading compiled-in X.509 certificates [ 7.191262][ T1] zswap: loaded using pool lzo/zbud [ 7.259514][ T1] Key type big_key registered [ 7.292566][ T1] Key type encrypted registered [ 7.299013][ T1] rtc-mv f1010300.rtc: setting system clock to 2019-09-23T07:15:38 UTC (1569222938) [ 7.388284][ T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 7.399769][ T112] ata1.00: ATA-7: TS16GSSD25H-M, 20100712, max UDMA/133 [ 7.406592][ T112] ata1.00: 31277056 sectors, multi 0: LBA48 [ 7.419139][ T112] ata1.00: configured for UDMA/133 [ 7.434511][ T7] scsi 0:0:0:0: Direct-Access ATA TS16GSSD25H-M 0712 PQ: 0 ANSI: 5 [ 7.444131][ T116] sd 0:0:0:0: [sda] 31277056 512-byte logical blocks: (16.0 GB/14.9 GiB) [ 7.452473][ T15] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 7.460359][ T116] sd 0:0:0:0: [sda] Write Protect is off [ 7.466050][ T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.477323][ T116] sda: sda1 [ 7.481558][ T116] sd 0:0:0:0: [sda] Attached SCSI disk [ 7.658780][ T15] usb 1-1: New USB device found, idVendor=058f, idProduct=6254, bcdDevice= 1.00 [ 7.667704][ T15] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 7.676007][ T15] hub 1-1:1.0: USB hub found [ 7.680649][ T15] hub 1-1:1.0: 4 ports detected [ 7.791869][ T114] ata2: SATA link down (SStatus 0 SControl F300) [ 7.811331][ T1] Freeing unused kernel memory: 1024K [ 7.816964][ T1] Checked W+X mappings: passed, no W+X pages found [ 7.823495][ T1] Run /init as init process Loading, please wait... Starting version 241 [ 8.363925][ T163] input: gpio_keys as /devices/platform/gpio_keys/input/input0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.33.1 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 sata_rootfs: clean, 20025/979200 files, 297293/3909376 blocks done. [ 18.863381][ T194] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 18.881355][ T194] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 131.668290][ C0] random: crng init done