Pogoplug Mobile Debian Install September 01, 2018 03:27PM |
Registered: 7 years ago Posts: 156 |
Boot default Pogoplug OS when USB/SD Card not attached Note that this section only works on a new unmodified Pogoplug. It assumes the command are all executed from within the default Pogoplug OS and not from Arch Linux or Debian. If you previously installed the uBoot from archlinuxarm.org and/or already running ALARM or Debian, use these instructions instead - Pogoplug v4 - Add option to boot default Pogoplug OS when USB/SD Card is Not Attached. To boot the default Pogoplug OS, we will need to chain load the original (dockstar) uboot which we'll download and store on the internal flash. The boot order will be USB, MMC/SD, SATA (Series 4 only) and then last, the original uBoot which will then load the default Pogoplug OS. Don't forget that you'll need to activate the Pogoplug on my.pogoplug.com if you plan on SSHing into the default Pogoplug OS. #remount '/' as read/write mount -o remount,rw / #download original uboot cd / wget http://download.doozan.com/uboot/files/uboot/uboot.mtd0.dockstar.original.kwb #update boot order to include pogoplug OS /tmp/fw_setenv bootcmd 'run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; run bootcmd_pogo; reset' #chain load original uboot /tmp/fw_setenv bootcmd_pogo 'if ubi part root 2048 && ubifsmount ubi:rootfs && ubifsload 0x800000 uboot.mtd0.dockstar.original.kwb ; then go 0x800200; fi'
Re: Pogoplug Mobile Debian Install September 01, 2018 03:36PM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Pogoplug Mobile Debian Install September 01, 2018 04:09PM |
Registered: 7 years ago Posts: 156 |
Quote
But it will not be running correctly as Pogo V4
Re: Pogoplug Mobile Debian Install September 01, 2018 04:55PM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Pogoplug Mobile Debian Install September 01, 2018 05:42PM |
Registered: 7 years ago Posts: 156 |
Re: Pogoplug Mobile Debian Install September 01, 2018 08:56PM |
Registered: 7 years ago Posts: 156 |
fw_setenv dtb_file '/boot/dts/kirkwood-dockstar.dtb'
fw_setenv dtb_file
Re: Pogoplug Mobile Debian Install September 01, 2018 09:06PM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Pogoplug Mobile Debian Install September 01, 2018 09:09PM |
Registered: 7 years ago Posts: 156 |
Re: Pogoplug Mobile Debian Install September 01, 2018 09:17PM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Pogoplug Mobile Debian Install September 01, 2018 11:51PM |
Registered: 7 years ago Posts: 156 |
[root@PogoplugMobile /tmp]# ls flash_erase hbplug.log resolv.conf fw_printenv nanddump uboot.2017.07-tld-1.pogo_v4.bodhi.tar fw_setenv nandwrite var [root@PogoplugMobile /tmp]# md5sum uboot.2017.07-tld-1.pogo_v4.bodhi.tar 62b5bf1fc998b35626bdca6106677fbd uboot.2017.07-tld-1.pogo_v4.bodhi.tar [root@PogoplugMobile /tmp]#
Re: Pogoplug Mobile Debian Install September 02, 2018 03:59AM |
Registered: 7 years ago Posts: 156 |
[root@PogoplugMobile /tmp]# md5sum uboot.2017.07-tld-1.pogo_v4.bodhi.tar 62b5bf1fc998b35626bdca6106677fbd uboot.2017.07-tld-1.pogo_v4.bodhi.tar [root@PogoplugMobile /tmp]# md5sum uboot.2016.05-tld-1.environment.bodhi.tar 62b5bf1fc998b35626bdca6106677fbd uboot.2016.05-tld-1.environment.bodhi.tar
Re: Pogoplug Mobile Debian Install September 02, 2018 04:53AM |
Admin Registered: 13 years ago Posts: 18,564 |
Quote
When I check the file on my mac after downloading from Dropbox I get the correct hash. I also get the correct hash when I download the same file I have hosted on my own server (this is where I wget the file from when I download to the Pogo
Re: Pogoplug Mobile Debian Install September 02, 2018 08:06AM |
Registered: 7 years ago Posts: 156 |
[root@PogoplugMobile /root]# wget --no-check-certificate https://www.dropbox.com/s/6k3a80jqdplpkeg/uboot.2017.07-tld-1.pogo _v4.bodhi.tar wget: unrecognized option `--no-check-certificate' Usage: wget [OPTION]... ...
Try `wget --help' for more options. [root@PogoplugMobile /root]# wget --help GNU Wget 1.12, a non-interactive network retriever. Usage: wget [OPTION]... ... Mandatory arguments to long options are mandatory for short options too. Startup: -V, --version display the version of Wget and exit. -h, --help print this help. -b, --background go to background after startup. -e, --execute=COMMAND execute a `.wgetrc'-style command. Logging and input file: -o, --output-file=FILE log messages to FILE. -a, --append-output=FILE append messages to FILE. -d, --debug print lots of debugging information. -q, --quiet quiet (no output). -v, --verbose be verbose (this is the default). -nv, --no-verbose turn off verboseness, without being quiet. -i, --input-file=FILE download URLs found in local or external FILE. -F, --force-html treat input file as HTML. -B, --base=URL resolves HTML input-file links (-i -F) relative to URL. Download: -t, --tries=NUMBER set number of retries to NUMBER (0 unlimits). --retry-connrefused retry even if connection is refused. -O, --output-document=FILE write documents to FILE. -nc, --no-clobber skip downloads that would download to existing files. -c, --continue resume getting a partially-downloaded file. --progress=TYPE select progress gauge type. -N, --timestamping don't re-retrieve files unless newer than local. -S, --server-response print server response. --spider don't download anything. -T, --timeout=SECONDS set all timeout values to SECONDS. --dns-timeout=SECS set the DNS lookup timeout to SECS. --connect-timeout=SECS set the connect timeout to SECS. --read-timeout=SECS set the read timeout to SECS. -w, --wait=SECONDS wait SECONDS between retrievals. --waitretry=SECONDS wait 1..SECONDS between retries of a retrieval. --random-wait wait from 0...2*WAIT secs between retrievals. --no-proxy explicitly turn off proxy. -Q, --quota=NUMBER set retrieval quota to NUMBER. --bind-address=ADDRESS bind to ADDRESS (hostname or IP) on local host. --limit-rate=RATE limit download rate to RATE. --no-dns-cache disable caching DNS lookups. --restrict-file-names=OS restrict chars in file names to ones OS allows. --ignore-case ignore case when matching files/directories. -4, --inet4-only connect only to IPv4 addresses. -6, --inet6-only connect only to IPv6 addresses. --prefer-family=FAMILY connect first to addresses of specified family, one of IPv6, IPv4, or none. --user=USER set both ftp and http user to USER. --password=PASS set both ftp and http password to PASS. --ask-password prompt for passwords. --no-iri turn off IRI support. --local-encoding=ENC use ENC as the local encoding for IRIs. --remote-encoding=ENC use ENC as the default remote encoding. Directories: -nd, --no-directories don't create directories. -x, --force-directories force creation of directories. -nH, --no-host-directories don't create host directories. --protocol-directories use protocol name in directories. -P, --directory-prefix=PREFIX save files to PREFIX/... --cut-dirs=NUMBER ignore NUMBER remote directory components. HTTP options: --http-user=USER set http user to USER. --http-password=PASS set http password to PASS. --no-cache disallow server-cached data. --default-page=NAME Change the default page name (normally this is `index.html'.). -E, --adjust-extension save HTML/CSS documents with proper extensions. --ignore-length ignore `Content-Length' header field. --header=STRING insert STRING among the headers. --max-redirect maximum redirections allowed per page. --proxy-user=USER set USER as proxy username. --proxy-password=PASS set PASS as proxy password. --referer=URL include `Referer: URL' header in HTTP request. --save-headers save the HTTP headers to file. -U, --user-agent=AGENT identify as AGENT instead of Wget/VERSION. --no-http-keep-alive disable HTTP keep-alive (persistent connections). --no-cookies don't use cookies. --load-cookies=FILE load cookies from FILE before session. --save-cookies=FILE save cookies to FILE after session. --keep-session-cookies load and save session (non-permanent) cookies. --post-data=STRING use the POST method; send STRING as the data. --post-file=FILE use the POST method; send contents of FILE. --content-disposition honor the Content-Disposition header when choosing local file names (EXPERIMENTAL). --auth-no-challenge send Basic HTTP authentication information without first waiting for the server's challenge. FTP options: --ftp-user=USER set ftp user to USER. --ftp-password=PASS set ftp password to PASS. --no-remove-listing don't remove `.listing' files. --no-glob turn off FTP file name globbing. --no-passive-ftp disable the "passive" transfer mode. --retr-symlinks when recursing, get linked-to files (not dir). Recursive download: -r, --recursive specify recursive download. -l, --level=NUMBER maximum recursion depth (inf or 0 for infinite). --delete-after delete files locally after downloading them. -k, --convert-links make links in downloaded HTML or CSS point to local files. -K, --backup-converted before converting file X, back up as X.orig. -m, --mirror shortcut for -N -r -l inf --no-remove-listing. -p, --page-requisites get all images, etc. needed to display HTML page. --strict-comments turn on strict (SGML) handling of HTML comments. Recursive accept/reject: -A, --accept=LIST comma-separated list of accepted extensions. -R, --reject=LIST comma-separated list of rejected extensions. -D, --domains=LIST comma-separated list of accepted domains. --exclude-domains=LIST comma-separated list of rejected domains. --follow-ftp follow FTP links from HTML documents. --follow-tags=LIST comma-separated list of followed HTML tags. --ignore-tags=LIST comma-separated list of ignored HTML tags. -H, --span-hosts go to foreign hosts when recursive. -L, --relative follow relative links only. -I, --include-directories=LIST list of allowed directories. -X, --exclude-directories=LIST list of excluded directories. -np, --no-parent don't ascend to the parent directory. Mail bug reports and suggestions to <bug-wget@gnu.org>.
[root@PogoplugMobile /tmp]# du -a -h 4.0K ./uboot.2016.05-tld-1.environment.bodhi.tar 4.0K ./uboot.2017.07-tld-1.pogo_v4.bodhi.tar 4.0K ./fw_setenv 4.0K ./fw_printenv 4.0K ./flash_erase 4.0K ./nandwrite 4.0K ./nanddump
[root@PogoplugMobile /tmp]# wget http://www.lenfertdesign.com/pogo/pogo-mobile-v4-debian/uboot.2017.07-tld-1.pogo_v4.bodhi. tar --2018-09-02 13:04:15-- http://my.domain.com/pogo/pogo-mobile-v4-debian/uboot.2017.07-tld-1.pogo_v4.bodhi.tar Resolving my.domain.com... 162.215.248.223 Connecting to my.domain.com|162.215.248.223|:80... connected. HTTP request sent, awaiting response... 200 OK Length: unspecified [text/html] Saving to: `uboot.2017.07-tld-1.pogo_v4.bodhi.tar.1' [ <=> ] 7 --.-K/s in 0s 2018-09-02 13:04:16 (204 KB/s) - `uboot.2017.07-tld-1.pogo_v4.bodhi.tar.1' saved [7]
Re: Pogoplug Mobile Debian Install September 02, 2018 11:55AM |
Registered: 9 years ago Posts: 226 |
root@debian:/tmp#wget http://www.lenfertdesign.com/pogo/asdf --2018-09-02 12:51:20-- http://www.lenfertdesign.com/pogo/asdf Resolving www.lenfertdesign.com (www.lenfertdesign.com)... 162.215.248.223 Connecting to www.lenfertdesign.com (www.lenfertdesign.com)|162.215.248.223|:80... connected. HTTP request sent, awaiting response... 200 OK Length: unspecified [text/html] Saving to: ‘asdf’ asdf [ <=> ] 7 --.-KB/s in 0s 2018-09-02 12:51:20 (24.0 KB/s) - ‘asdf’ saved [7] root@debian:/tmp# md5sum asdf 62b5bf1fc998b35626bdca6106677fbd asdf root@debian:/tmp# ls -la asdf -rw-r--r-- 1 root root 7 Sep 2 12:51 asdf
wget -O uboot.2017.07-tld-1.pogo_v4.bodhi.tar "https://uc5f8764e008f7aeaba73ca1b4a6.dl.dropboxusercontent.com/cd/0/get/APhyv697J7wTOENnB6WcJg5b_EXQ1dpa-44H7s5-UQVMRIueq1snIeQ8ByMn7TOVn8e4mvZEyWlAYue_LP0PgBSlx4TcgpN67S2IK2f8V4HupICRlY2RlB-aQBSgKGDgT0MRMSlm_3greMlLMXhSn6sxqOAsfhiEbvbAmq2QRs6vaakqqJel6Y43fJwR3wuFgOo/file?_download_id=124575681663902872012049707605899692080703948951554099193509579131&_notify_domain=www.dropbox.com&dl=1"-JT
Re: Pogoplug Mobile Debian Install September 02, 2018 04:44PM |
Registered: 7 years ago Posts: 156 |
[root@PogoplugMobile /root]# cat /sys/class/net/eth0/address 00:25:31:03:49:49 #from router #00:25:31:03:49:49 (matches above) also matches sticker on Pogo [root@PogoplugMobile /tmp]# /tmp/fw_printenv ethaddr ethaddr=52:3b:20:9c:11:51 #!!! this is different than what I had before [root@PogoplugMobile /tmp]# /tmp/fw_setenv ethaddr "$(cat /sys/class/net/eth0/address)" Can't overwrite "ethaddr" [root@PogoplugMobile /tmp]# /tmp/fw_setenv ethaddr "00:25:31:03:49:49" Can't overwrite "ethaddr"
Re: Pogoplug Mobile Debian Install September 02, 2018 04:49PM |
Registered: 7 years ago Posts: 156 |
[root@PogoplugMobile /tmp]# /tmp/fw_printenv bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking dtb_file=/boot/dts/kirkwood-pogo_e02.dtb load_dtb_addr=0x1c00000 load_initrd_addr=0x1100000 load_uimage_addr=0x800000 load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage mainlineLinux=yes mtdids=nand0=orion_nand partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi usb_ready_retry=15 arcNumber=3960 machid=f78 usb_rootfstype=ext3 mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
Re: Pogoplug Mobile Debian Install September 02, 2018 04:56PM |
Admin Registered: 13 years ago Posts: 18,564 |
dtb_file=/boot/dts/kirkwood-pogo_e02.dtb
Re: Pogoplug Mobile Debian Install September 02, 2018 04:59PM |
Registered: 7 years ago Posts: 156 |
Now for my next stumper. I'm unable to overwrite my ethernet address. The last 2 commands show where it fails to overwrite. How big of a problem is this? [root@PogoplugMobile /root]# cat /sys/class/net/eth0/address 00:25:31:03:49:49 #from router #00:25:31:03:49:49 (matches above) also matches sticker on Pogo [root@PogoplugMobile /tmp]# /tmp/fw_printenv ethaddr ethaddr=52:3b:20:9c:11:51 #!!! this is different than what I had before [root@PogoplugMobile /tmp]# /tmp/fw_setenv ethaddr "$(cat /sys/class/net/eth0/address)" Can't overwrite "ethaddr" [root@PogoplugMobile /tmp]# /tmp/fw_setenv ethaddr "00:25:31:03:49:49" Can't overwrite "ethaddr"
Re: Pogoplug Mobile Debian Install September 02, 2018 05:02PM |
Admin Registered: 13 years ago Posts: 18,564 |
> Now for my next stumper. I'm unable to overwrite > my ethernet address. The last 2 commands show > where it fails to overwrite. How big of a problem > is this? > > [root@PogoplugMobile /root]# cat > /sys/class/net/eth0/address > 00:25:31:03:49:49 > > #from router > #00:25:31:03:49:49 (matches above) also matches > sticker on Pogo > > [root@PogoplugMobile /tmp]# /tmp/fw_printenv > ethaddr > ethaddr=52:3b:20:9c:11:51 > #!!! this is different than what I had before > > [root@PogoplugMobile /tmp]# /tmp/fw_setenv ethaddr > "$(cat /sys/class/net/eth0/address)" > Can't overwrite "ethaddr" > > [root@PogoplugMobile /tmp]# /tmp/fw_setenv ethaddr > "00:25:31:03:49:49" > Can't overwrite "ethaddr" >
Re: Pogoplug Mobile Debian Install September 02, 2018 05:08PM |
Registered: 7 years ago Posts: 156 |
fw_setenv dtb_file '/boot/dts/pogoplug_v4.dtb'
Re: Pogoplug Mobile Debian Install September 02, 2018 05:20PM |
Admin Registered: 13 years ago Posts: 18,564 |
fw_setenv dtb_file '/boot/dts/kirkwood-pogoplug_v4.dtb'
Re: Pogoplug Mobile Debian Install September 02, 2018 06:49PM |
Registered: 7 years ago Posts: 156 |
Re: Pogoplug Mobile Debian Install September 02, 2018 08:50PM |
Registered: 7 years ago Posts: 156 |
bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_pogo; reset
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec
Re: Pogoplug Mobile Debian Install September 03, 2018 02:27PM |
Admin Registered: 13 years ago Posts: 18,564 |
fw_setenv bootcmd_exec 'if run load_uimage; then; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi; fi' fw_setenv bootcmd 'run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; run bootcmd_pogo'
Re: Pogoplug Mobile Debian Install September 03, 2018 03:05PM |
Registered: 7 years ago Posts: 156 |
[root@PogoplugMobile /]# /tmp/fw_printenv bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb_addr=0x1c00000 load_initrd_addr=0x1100000 load_uimage_addr=0x800000 load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage mainlineLinux=yes mtdids=nand0=orion_nand partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi usb_ready_retry=15 arcNumber=3960 machid=f78 usb_rootfstype=ext3 mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb bootcmd_pogo=if ubi part root 2048 && ubifsmount ubi:rootfs && ubifsload 0x800000 uboot.mtd0.dockstar.original.kwb ; then go 0x800200; fi bootcmd_exec=if run load_uimage; then; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi; fi bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; run bootcmd_pogo
Re: Pogoplug Mobile Debian Install September 03, 2018 04:00PM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Pogoplug Mobile Debian Install September 03, 2018 04:06PM |
Registered: 7 years ago Posts: 156 |
Re: Pogoplug Mobile Debian Install September 06, 2018 09:02PM |
Registered: 7 years ago Posts: 156 |
Re: Pogoplug Mobile Debian Install September 06, 2018 10:07PM |
Registered: 11 years ago Posts: 1,303 |
Re: Pogoplug Mobile Debian Install September 06, 2018 11:34PM |
Admin Registered: 13 years ago Posts: 18,564 |
Quote
Backup and Cloning rootfs
CrashPlan 4.3.0
Backup/Restore rootfs using tar command
Adjust udev rules after cloning rootfs
Stock Pogoplug rootfs
How to clone a rootfs from one Kirkwood box to another: Step 1 and Step 2
How to clone SATA rootfs to USB rootfs
Quote
To restore it later when needed, use the same command that I have in the instruction in the first post. For example:
cd /media/mmcblk0p1
tar -xjf /media/sda1/my-rootfs.tar.bz2