Debian on Chip PC LXD8941
Posted by Koen
|
Re: Chip PC LXD8941 October 01, 2018 05:09PM |
Admin Registered: 13 years ago Posts: 19,192 |
Koen
Please post the serial bootlog with the new DTB appended.
And list the modules
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 10/01/2018 05:16PM by bodhi.
I've appended the new dtb and booted the device but when I insert a microSD card it is not recognised. After that I've used the following instructions to add gpio 12.
Please post the serial bootlog with the new DTB appended.
And list the modules
lsmod
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 10/01/2018 05:16PM by bodhi.
|
Re: Chip PC LXD8941 October 01, 2018 05:23PM |
Registered: 6 years ago Posts: 183 |
bootlog:
lsmod:
MIC>> setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 ${mtdparts} earlyprintk=serial'
MIC>> setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x3000000 /boot/uImage; ext2load usb 0:1 0x4000000 /boot/uInitrd'
MIC>> setenv bootcmd_exec 'run set_bootargs; run bootcmd_usb; bootm 0x3000000 0x4000000'
MIC>> run bootcmd_exec
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
......
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
..........................
4465719 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
......
......
............
.........................
...................................................
......................................................................................................
......................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
................................
8721585 bytes read
## Booting kernel from Legacy Image at 03000000 ...
Image Name: Linux-4.18.5-mvebu-tld-1
Created: 2018-10-01 20:31:50 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4465655 Bytes = 4.3 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 04000000 ...
Image Name: initramfs-4.18.5-mvebu-tld-1
Created: 2018-09-29 17:33:30 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 8721521 Bytes = 8.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
EUGENE lcd_disable
EUGENE lcd_panel_disable
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.18.5-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9)) #1 SMP PREEMPT Thu Aug 30 22:19:21 PDT 2018
[ 0.000000] CPU: ARMv7 Processor [413fc081] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Chip PC LXD8941
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] random: get_random_bytes called from start_kernel+0x78/0x4c4 with crng_init=0
[ 0.000000] percpu: Embedded 18 pages/cpu @(ptrval) s41548 r8192 d23988 u73728
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi0.0:768k(uboot),256k(uboot_env),768k(uboot2),-(kernel) earlyprintk=serial
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1016480K/1048576K available (9216K kernel code, 790K rwdata, 2304K rodata, 1024K init, 327K bss, 32096K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (10208 kB)
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 791 kB)
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 328 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.18.5-mvebu-tld-1 #1
[ 0.000000] Hardware name: Marvell Dove
[ 0.000000] [<c0117d00>] (unwind_backtrace) from [<c0112680>] (show_stack+0x10/0x14)
[ 0.000000] [<c0112680>] (show_stack) from [<c0944f18>] (dump_stack+0x70/0x8c)
[ 0.000000] [<c0944f18>] (dump_stack) from [<c0943574>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c0943574>] (Ldiv0) from [<c05c2fbc>] (dove_recalc_rate+0x44/0x8c)
[ 0.000000] [<c05c2fbc>] (dove_recalc_rate) from [<c05bed1c>] (clk_register+0x40c/0x5d4)
[ 0.000000] [<c05bed1c>] (clk_register) from [<c0d35580>] (dove_divider_clk_init+0x12c/0x190)
[ 0.000000] [<c0d35580>] (dove_divider_clk_init) from [<c0d353c8>] (dove_clk_init+0x4c/0x74)
[ 0.000000] [<c0d353c8>] (dove_clk_init) from [<c0d3353c>] (of_clk_init+0x184/0x240)
[ 0.000000] [<c0d3353c>] (of_clk_init) from [<c0d04004>] (time_init+0x20/0x2c)
[ 0.000000] [<c0d04004>] (time_init) from [<c0d00d14>] (start_kernel+0x2f8/0x4c4)
[ 0.000000] [<c0d00d14>] (start_kernel) from [<00000000>] ( (null))
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[ 0.000007] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[ 0.007824] Switching to timer-based delay loop, resolution 6ns
[ 0.014458] Console: colour dummy device 80x30
[ 0.018956] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[ 0.029471] pid_max: default: 32768 minimum: 301
[ 0.034307] Security Framework initialized
[ 0.038543] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.045144] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.053176] CPU: Testing write buffer coherency: ok
[ 0.058114] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[ 0.067934] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.127982] Setting up static identity map for 0x100000 - 0x100060
[ 0.134914] Hierarchical SRCU implementation.
[ 0.177885] smp: Bringing up secondary CPUs ...
[ 0.182407] smp: Brought up 1 node, 1 CPU
[ 0.186397] SMP: Total of 1 processors activated (333.33 BogoMIPS).
[ 0.192690] CPU: All CPU(s) started in SVC mode.
[ 0.198318] devtmpfs: initialized
[ 0.208120] VFP support v0.3: implementor 41 architecture 2 part 20 variant 9 rev 5
[ 0.216547] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.226740] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.233237] prandom: seed boundary self test passed
[ 0.241425] prandom: 100 self tests passed
[ 0.245503] pinctrl core: initialized pinctrl subsystem
[ 0.253335] NET: Registered protocol family 16
[ 0.259616] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.267001] audit: initializing netlink subsys (disabled)
[ 0.274958] audit: type=2000 audit(0.260:1): state=initialized audit_enabled=0 res=1
[ 0.298167] cpuidle: using governor ladder
[ 0.302377] cpuidle: using governor menu
[ 0.306513] Dove 88AP510 SoC
[ 0.309509] Tauros2: Disabling L2 prefetch.
[ 0.313679] Tauros2: Disabling burst8 line fill.
[ 0.318390] Tauros2: Enabling L2 cache.
[ 0.322208] Tauros2: L2 cache support initialised in ARMv7 mode.
[ 0.328612] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.428829] vgaarb: loaded
[ 0.431862] SCSI subsystem initialized
[ 0.438421] usbcore: registered new interface driver usbfs
[ 0.443933] usbcore: registered new interface driver hub
[ 0.450357] usbcore: registered new device driver usb
[ 0.456150] media: Linux media interface: v0.10
[ 0.461257] videodev: Linux video capture interface: v2.00
[ 0.467255] pps_core: LinuxPPS API ver. 1 registered
[ 0.472618] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.481945] PTP clock support registered
[ 0.488215] clocksource: Switched to clocksource orion_clocksource
[ 0.581468] VFS: Disk quotas dquot_6.6.0
[ 0.585446] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.612678] NET: Registered protocol family 2
[ 0.618890] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.626525] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.633958] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.640506] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.646938] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.652930] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.659522] NET: Registered protocol family 1
[ 0.694563] RPC: Registered named UNIX socket transport module.
[ 0.700529] RPC: Registered udp transport module.
[ 0.705209] RPC: Registered tcp transport module.
[ 0.709928] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.716555] Unpacking initramfs...
[ 1.272757] Freeing initrd memory: 8520K
[ 1.276873] NetWinder Floating Point Emulator V0.97 (double precision)
[ 1.286061] Initialise system trusted keyrings
[ 1.291577] Key type blacklist registered
[ 1.295772] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 1.302388] zbud: loaded
[ 1.315964] NFS: Registering the id_resolver key type
[ 1.321207] Key type id_resolver registered
[ 1.325371] Key type id_legacy registered
[ 1.329435] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.336103] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.342759] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.350367] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 1.356961] orangefs_init: module version upstream loaded
[ 1.369022] Key type asymmetric registered
[ 1.373100] Asymmetric key parser 'x509' registered
[ 1.378026] bounce: pool size: 64 pages
[ 1.382094] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 1.389782] io scheduler noop registered
[ 1.393688] io scheduler deadline registered
[ 1.398005] io scheduler cfq registered (default)
[ 1.404969] dove-pinctrl f10d0200.pin-ctrl: falling back to hardcoded PMU resource
[ 1.413571] dove-pinctrl f10d0200.pin-ctrl: [Firmware Bug]: Missing pinctrl regs in DTB. Please update your firmware.
[ 1.424908] dove-pinctrl f10d0200.pin-ctrl: registered pinctrl driver
[ 1.436448] mvebu-pcie mbus:pcie: PCI host bridge to bus 0000:00
[ 1.443528] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 1.449934] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 1.456783] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.464361] PCI: bus0: Fast back to back transfers disabled
[ 1.470148] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.478128] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.487546] PCI: bus1: Fast back to back transfers enabled
[ 1.494579] PCI: bus2: Fast back to back transfers enabled
[ 1.500224] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 1.505173] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 1.511297] mv_xor f1060800.dma-engine: Marvell shared XOR driver
[ 1.579304] mv_xor f1060800.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 1.587591] mv_xor f1060900.dma-engine: Marvell shared XOR driver
[ 1.649300] mv_xor f1060900.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 1.790832] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.801109] console [ttyS0] disabled
[ 1.805380] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 21, base_baud = 10416666) is a 16550A
[ 1.814630] console [ttyS0] enabled
[ 1.814630] console [ttyS0] enabled
[ 1.821751] bootconsole [earlycon0] disabled
[ 1.821751] bootconsole [earlycon0] disabled
[ 1.831487] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 22, base_baud = 10416666) is a 16550A
[ 1.842624] sata_mv f10a0000.sata-host: slots 32 ports 1
[ 1.860269] scsi host0: sata_mv
[ 1.863955] ata1: SATA max UDMA/133 irq 33
[ 1.870102] m25p80 spi0.0: found mx25l1606e, expected sst25vf080b
[ 1.876181] m25p80 spi0.0: mx25l1606e (2048 Kbytes)
[ 1.882594] 4 cmdlinepart partitions found on MTD device spi0.0
[ 1.888558] Creating 4 MTD partitions on "spi0.0":
[ 1.893330] 0x000000000000-0x0000000c0000 : "uboot"
[ 1.899811] 0x0000000c0000-0x000000100000 : "uboot_env"
[ 1.906580] 0x000000100000-0x0000001c0000 : "uboot2"
[ 1.913155] 0x0000001c0000-0x000000200000 : "kernel"
[ 1.922460] libphy: Fixed MDIO Bus: probed
[ 1.930303] libphy: orion_mdio_bus: probed
[ 1.942245] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 2.049558] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:05:35:09:92:9a
[ 2.059402] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.065918] ehci-pci: EHCI PCI platform driver
[ 2.070925] ehci-orion: EHCI orion driver
[ 2.075089] orion-ehci f1050000.usb-host: EHCI Host Controller
[ 2.081070] orion-ehci f1050000.usb-host: new USB bus registered, assigned bus number 1
[ 2.089517] orion-ehci f1050000.usb-host: irq 26, io mem 0xf1050000
[ 2.118250] orion-ehci f1050000.usb-host: USB 2.0 started, EHCI 1.00
[ 2.124869] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[ 2.133146] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.140377] usb usb1: Product: EHCI Host Controller
[ 2.145234] usb usb1: Manufacturer: Linux 4.18.5-mvebu-tld-1 ehci_hcd
[ 2.151685] usb usb1: SerialNumber: f1050000.usb-host
[ 2.157487] hub 1-0:1.0: USB hub found
[ 2.161473] hub 1-0:1.0: 1 port detected
[ 2.166156] orion-ehci f1051000.usb-host: EHCI Host Controller
[ 2.172276] orion-ehci f1051000.usb-host: new USB bus registered, assigned bus number 2
[ 2.180471] orion-ehci f1051000.usb-host: irq 27, io mem 0xf1051000
[ 2.201965] ata1: SATA link down (SStatus 0 SControl F300)
[ 2.208257] orion-ehci f1051000.usb-host: USB 2.0 started, EHCI 1.00
[ 2.214839] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[ 2.223128] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.230342] usb usb2: Product: EHCI Host Controller
[ 2.235201] usb usb2: Manufacturer: Linux 4.18.5-mvebu-tld-1 ehci_hcd
[ 2.241632] usb usb2: SerialNumber: f1051000.usb-host
[ 2.247367] hub 2-0:1.0: USB hub found
[ 2.251342] hub 2-0:1.0: 1 port detected
[ 2.256685] usbcore: registered new interface driver usblp
[ 2.262865] usbcore: registered new interface driver usb-storage
[ 2.269527] mousedev: PS/2 mouse device common for all mice
[ 2.276476] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time-clock as rtc0
[ 2.286360] i2c /dev entries driver
[ 2.289866] random: fast init done
[ 2.296367] orion_wdt: Initial timeout 25 sec
[ 2.304994] marvell-cesa f1030000.crypto-engine: CESA device successfully registered
[ 2.313429] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.319922] usbcore: registered new interface driver usbhid
[ 2.325468] usbhid: USB HID core driver
[ 2.330268] drop_monitor: Initializing network drop monitor service
[ 2.336970] NET: Registered protocol family 10
[ 2.352964] Segment Routing with IPv6
[ 2.356696] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.364724] NET: Registered protocol family 17
[ 2.369629] 8021q: 802.1Q VLAN Support v1.8
[ 2.373834] Key type dns_resolver registered
[ 2.378512] ThumbEE CPU extension supported.
[ 2.382769] Registering SWP/SWPB emulation handler
[ 2.388540] registered taskstats version 1
[ 2.392620] Loading compiled-in X.509 certificates
[ 2.397453] zswap: loaded using pool lzo/zbud
[ 2.418806] Key type big_key registered
[ 2.430415] Key type encrypted registered
[ 2.437392] rtc-mv f10d8500.real-time-clock: setting system clock to 2006-08-24 06:03:24 UTC (1156399404)
[ 2.450170] Freeing unused kernel memory: 1024K
[ 2.456736] Checked W+X mappings: passed, no W+X pages found
Loading, please wait...
[ 2.528330] usb 1-1: new high-speed USB device number 2 using orion-ehci
starting version 232
[ 2.570918] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 2.583652] random: udevadm: uninitialized urandom read (16 bytes read)
[ 2.590847] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 2.618308] usb 2-1: new high-speed USB device number 2 using orion-ehci
[ 2.740144] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98
[ 2.758320] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.765431] usb 1-1: Product: USB2.0 Hub
[ 2.786723] hub 1-1:1.0: USB hub found
[ 2.799345] hub 1-1:1.0: 4 ports detected
[ 2.840219] usb 2-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98
[ 2.858337] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.865448] usb 2-1: Product: USB2.0 Hub
[ 2.886183] hub 2-1:1.0: USB hub found
[ 2.899735] hub 2-1:1.0: 4 ports detected
[ 3.124551] i2c i2c-0: Added multiplexed i2c bus 1
[ 3.129472] usb 1-1.4: new high-speed USB device number 3 using orion-ehci
[ 3.164812] i2c i2c-0: Added multiplexed i2c bus 2
[ 3.196104] i2c i2c-0: Added multiplexed i2c bus 3
[ 3.293282] sdhci: Secure Digital Host Controller Interface driver
[ 3.300638] usb 1-1.4: New USB device found, idVendor=0781, idProduct=5530, bcdDevice= 1.26
[ 3.315850] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.330333] usb 1-1.4: Product: Cruzer
[ 3.334073] usb 1-1.4: Manufacturer: SanDisk
[ 3.343356] sdhci: Copyright(c) Pierre Ossman
[ 3.347740] usb 1-1.4: SerialNumber: 20060775210A3B80C5B2
[ 3.353972] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.360593] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 3.377918] mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
[ 3.386155] scsi host1: usb-storage 1-1.4:1.0
[ 3.445427] mmc0: SDHCI controller on f1090000.sdio-host [f1090000.sdio-host] using DMA
[ 3.469269] mmc1 bounce up to 128 segments into one, max segment size 65536 bytes
[ 3.521410] mmc1: SDHCI controller on f1092000.sdio-host [f1092000.sdio-host] using DMA
[ 3.574490] mmc1: new high speed MMC card at address 0001
[ 4.409866] scsi 1:0:0:0: Direct-Access SanDisk Cruzer 1.26 PQ: 0 ANSI: 5
[ 4.427196] sd 1:0:0:0: [sda] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB)
[ 4.442311] sd 1:0:0:0: [sda] Write Protect is off
[ 4.451014] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 4.480305] sda: sda1
[ 4.486052] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 4.596826] usbcore: registered new interface driver uas
[ 4.612593] mmcblk1: mmc1:0001 SEM02G 1.82 GiB
[ 4.617496] mmcblk1boot0: mmc1:0001 SEM02G partition 1 1.00 MiB
[ 4.648887] mmcblk1boot1: mmc1:0001 SEM02G partition 2 1.00 MiB
[ 4.656488] mmcblk1rpmb: mmc1:0001 SEM02G partition 3 128 KiB, chardev (242:0)
[ 4.675109] mmcblk1: p1 p2 p3
[ 4.678941] mmcblk1: p3 size 1831410 extends beyond EOD, truncated
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.29.2
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1
rootfs: clean, 26714/488640 files, 378694/1953536 blocks
done.
[ 15.226094] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 15.254919] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Setting hostname to 'debian'...done.
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
. ok
[ ok ] Synthesizing the initial hotplug events...done.
[....] Waiting for /dev to be fully populated...[ 18.030621] sd 1:0:0:0: Attached scsi generic sg0 type 0
done.
[ ok ] Activating swap:.
[ 20.664505] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 20.909581] random: crng init done
[ 20.912980] random: 7 urandom warning(s) missed due to ratelimiting
[ ok ] Will now activate lvm and md swap:done.
[info] Will now check all file systems.
fsck from util-linux 2.29.2
Checking all file systems.
LABEL=rootfs is mounted
[ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables...done.
[ ok ] Initializing random number generator...done.
[ 23.589259] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 25.995202] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 26.005054] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5
Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:05:35:09:92:9a
Sending on LPF/eth0/00:05:35:09:92:9a
Sending on Socket/fallback
DHCPREQUEST of 192.168.1.135 on eth0 to 255.255.255.255 port 67
DHCPREQUEST of 192.168.1.135 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.1.135 from 192.168.1.1
bound to 192.168.1.135 -- renewal in 20573 seconds.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
[ ok ] Setting up ALSA...done (none loaded).
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2567 (syslogd)
. ok
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2566 (klogd)
. ok
[ ok ] Starting NTP server: ntpd.
[ ok ] Running local boot scripts (/etc/rc.local).
Debian GNU/Linux 9 debian ttyS0
debian login:
lsmod:
root@debian:~# lsmod Module Size Used by armada 45056 0 drm_kms_helper 114688 1 armada drm 294912 2 armada,drm_kms_helper drm_panel_orientation_quirks 16384 1 drm fb_sys_fops 16384 1 drm_kms_helper syscopyarea 16384 1 drm_kms_helper sysfillrect 16384 1 drm_kms_helper sysimgblt 16384 1 drm_kms_helper cfbfillrect 16384 1 drm_kms_helper cfbimgblt 16384 1 drm_kms_helper cfbcopyarea 16384 1 drm_kms_helper sg 32768 0 uio_pdrv_genirq 16384 0 uio 20480 1 uio_pdrv_genirq mmc_block 36864 0 uas 20480 0 sdhci_dove 16384 0 sdhci_pltfm 16384 1 sdhci_dove sdhci 49152 2 sdhci_dove,sdhci_pltfm mmc_core 122880 3 sdhci_dove,sdhci,mmc_block i2c_mux_pinctrl 16384 0 root@debian:~#
|
Re: Chip PC LXD8941 October 01, 2018 05:57PM |
Admin Registered: 13 years ago Posts: 19,192 |
Koen,
Sorry, I meant the boot log without the card inserted. And then plug in the card. List the modules.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Sorry, I meant the boot log without the card inserted. And then plug in the card. List the modules.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Chip PC LXD8941 October 01, 2018 06:25PM |
Registered: 6 years ago Posts: 183 |
Here the boot log from serial console. When I plug in the card there is no new output to console.
MIC>> setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 ${mtdparts} earlyprintk=serial'
MIC>> setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x3000000 /boot/uImage; ext2load usb 0:1 0x4000000 /boot/uInitrd'
MIC>> setenv bootcmd_exec 'run set_bootargs; run bootcmd_usb; bootm 0x3000000 0x4000000'
MIC>> run bootcmd_exec
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
......
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
..........................
4465719 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
......
......
............
.........................
...................................................
......................................................................................................
......................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
................................
8721585 bytes read
## Booting kernel from Legacy Image at 03000000 ...
Image Name: Linux-4.18.5-mvebu-tld-1
Created: 2018-10-01 20:31:50 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4465655 Bytes = 4.3 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 04000000 ...
Image Name: initramfs-4.18.5-mvebu-tld-1
Created: 2018-09-29 17:33:30 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 8721521 Bytes = 8.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
EUGENE lcd_disable
EUGENE lcd_panel_disable
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.18.5-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9)) #1 SMP PREEMPT Thu Aug 30 22:19:21 PDT 2018
[ 0.000000] CPU: ARMv7 Processor [413fc081] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Chip PC LXD8941
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] random: get_random_bytes called from start_kernel+0x78/0x4c4 with crng_init=0
[ 0.000000] percpu: Embedded 18 pages/cpu @(ptrval) s41548 r8192 d23988 u73728
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi0.0:768k(uboot),256k(uboot_env),768k(uboot2),-(kernel) earlyprintk=serial
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1016480K/1048576K available (9216K kernel code, 790K rwdata, 2304K rodata, 1024K init, 327K bss, 32096K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (10208 kB)
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 791 kB)
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 328 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.18.5-mvebu-tld-1 #1
[ 0.000000] Hardware name: Marvell Dove
[ 0.000000] [<c0117d00>] (unwind_backtrace) from [<c0112680>] (show_stack+0x10/0x14)
[ 0.000000] [<c0112680>] (show_stack) from [<c0944f18>] (dump_stack+0x70/0x8c)
[ 0.000000] [<c0944f18>] (dump_stack) from [<c0943574>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c0943574>] (Ldiv0) from [<c05c2fbc>] (dove_recalc_rate+0x44/0x8c)
[ 0.000000] [<c05c2fbc>] (dove_recalc_rate) from [<c05bed1c>] (clk_register+0x40c/0x5d4)
[ 0.000000] [<c05bed1c>] (clk_register) from [<c0d35580>] (dove_divider_clk_init+0x12c/0x190)
[ 0.000000] [<c0d35580>] (dove_divider_clk_init) from [<c0d353c8>] (dove_clk_init+0x4c/0x74)
[ 0.000000] [<c0d353c8>] (dove_clk_init) from [<c0d3353c>] (of_clk_init+0x184/0x240)
[ 0.000000] [<c0d3353c>] (of_clk_init) from [<c0d04004>] (time_init+0x20/0x2c)
[ 0.000000] [<c0d04004>] (time_init) from [<c0d00d14>] (start_kernel+0x2f8/0x4c4)
[ 0.000000] [<c0d00d14>] (start_kernel) from [<00000000>] ( (null))
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[ 0.000007] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[ 0.007824] Switching to timer-based delay loop, resolution 6ns
[ 0.014457] Console: colour dummy device 80x30
[ 0.018956] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[ 0.029471] pid_max: default: 32768 minimum: 301
[ 0.034306] Security Framework initialized
[ 0.038537] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.045135] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.053167] CPU: Testing write buffer coherency: ok
[ 0.058105] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[ 0.067922] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.127980] Setting up static identity map for 0x100000 - 0x100060
[ 0.134904] Hierarchical SRCU implementation.
[ 0.177887] smp: Bringing up secondary CPUs ...
[ 0.182406] smp: Brought up 1 node, 1 CPU
[ 0.186397] SMP: Total of 1 processors activated (333.33 BogoMIPS).
[ 0.192690] CPU: All CPU(s) started in SVC mode.
[ 0.198315] devtmpfs: initialized
[ 0.208118] VFP support v0.3: implementor 41 architecture 2 part 20 variant 9 rev 5
[ 0.216541] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.226743] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.233235] prandom: seed boundary self test passed
[ 0.241425] prandom: 100 self tests passed
[ 0.245503] pinctrl core: initialized pinctrl subsystem
[ 0.253354] NET: Registered protocol family 16
[ 0.259630] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.267012] audit: initializing netlink subsys (disabled)
[ 0.274964] audit: type=2000 audit(0.260:1): state=initialized audit_enabled=0 res=1
[ 0.298166] cpuidle: using governor ladder
[ 0.302371] cpuidle: using governor menu
[ 0.306506] Dove 88AP510 SoC
[ 0.309502] Tauros2: Disabling L2 prefetch.
[ 0.313670] Tauros2: Disabling burst8 line fill.
[ 0.318383] Tauros2: Enabling L2 cache.
[ 0.322207] Tauros2: L2 cache support initialised in ARMv7 mode.
[ 0.328610] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.428823] vgaarb: loaded
[ 0.431852] SCSI subsystem initialized
[ 0.438365] usbcore: registered new interface driver usbfs
[ 0.443871] usbcore: registered new interface driver hub
[ 0.450322] usbcore: registered new device driver usb
[ 0.456115] media: Linux media interface: v0.10
[ 0.461227] videodev: Linux video capture interface: v2.00
[ 0.467224] pps_core: LinuxPPS API ver. 1 registered
[ 0.472584] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.481908] PTP clock support registered
[ 0.488198] clocksource: Switched to clocksource orion_clocksource
[ 0.581275] VFS: Disk quotas dquot_6.6.0
[ 0.585255] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.612698] NET: Registered protocol family 2
[ 0.618903] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.626543] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.633974] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.640523] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.646955] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.652945] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.659539] NET: Registered protocol family 1
[ 0.694572] RPC: Registered named UNIX socket transport module.
[ 0.700539] RPC: Registered udp transport module.
[ 0.705217] RPC: Registered tcp transport module.
[ 0.709936] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.716566] Unpacking initramfs...
[ 1.272621] Freeing initrd memory: 8520K
[ 1.276734] NetWinder Floating Point Emulator V0.97 (double precision)
[ 1.285977] Initialise system trusted keyrings
[ 1.291500] Key type blacklist registered
[ 1.295688] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 1.302301] zbud: loaded
[ 1.315876] NFS: Registering the id_resolver key type
[ 1.321126] Key type id_resolver registered
[ 1.325284] Key type id_legacy registered
[ 1.329349] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.336016] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.342671] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.350278] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 1.356874] orangefs_init: module version upstream loaded
[ 1.368953] Key type asymmetric registered
[ 1.373030] Asymmetric key parser 'x509' registered
[ 1.377956] bounce: pool size: 64 pages
[ 1.382024] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 1.389718] io scheduler noop registered
[ 1.393619] io scheduler deadline registered
[ 1.397937] io scheduler cfq registered (default)
[ 1.404914] dove-pinctrl f10d0200.pin-ctrl: falling back to hardcoded PMU resource
[ 1.413513] dove-pinctrl f10d0200.pin-ctrl: [Firmware Bug]: Missing pinctrl regs in DTB. Please update your firmware.
[ 1.424853] dove-pinctrl f10d0200.pin-ctrl: registered pinctrl driver
[ 1.436412] mvebu-pcie mbus:pcie: PCI host bridge to bus 0000:00
[ 1.443503] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 1.449917] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 1.456765] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.464359] PCI: bus0: Fast back to back transfers disabled
[ 1.470139] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.478119] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.487537] PCI: bus1: Fast back to back transfers enabled
[ 1.494578] PCI: bus2: Fast back to back transfers enabled
[ 1.500223] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 1.505172] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 1.511297] mv_xor f1060800.dma-engine: Marvell shared XOR driver
[ 1.579342] mv_xor f1060800.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 1.587631] mv_xor f1060900.dma-engine: Marvell shared XOR driver
[ 1.649330] mv_xor f1060900.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 1.790998] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.801305] console [ttyS0] disabled
[ 1.805574] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 21, base_baud = 10416666) is a 16550A
[ 1.814835] console [ttyS0] enabled
[ 1.814835] console [ttyS0] enabled
[ 1.821958] bootconsole [earlycon0] disabled
[ 1.821958] bootconsole [earlycon0] disabled
[ 1.831695] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 22, base_baud = 10416666) is a 16550A
[ 1.842840] sata_mv f10a0000.sata-host: slots 32 ports 1
[ 1.860473] scsi host0: sata_mv
[ 1.864150] ata1: SATA max UDMA/133 irq 33
[ 1.870408] m25p80 spi0.0: found mx25l1606e, expected sst25vf080b
[ 1.876482] m25p80 spi0.0: mx25l1606e (2048 Kbytes)
[ 1.882783] 4 cmdlinepart partitions found on MTD device spi0.0
[ 1.888743] Creating 4 MTD partitions on "spi0.0":
[ 1.893519] 0x000000000000-0x0000000c0000 : "uboot"
[ 1.899870] 0x0000000c0000-0x000000100000 : "uboot_env"
[ 1.906667] 0x000000100000-0x0000001c0000 : "uboot2"
[ 1.913386] 0x0000001c0000-0x000000200000 : "kernel"
[ 1.922672] libphy: Fixed MDIO Bus: probed
[ 1.930529] libphy: orion_mdio_bus: probed
[ 1.942512] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 2.049558] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:05:35:09:92:9a
[ 2.059404] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.065928] ehci-pci: EHCI PCI platform driver
[ 2.070932] ehci-orion: EHCI orion driver
[ 2.075096] orion-ehci f1050000.usb-host: EHCI Host Controller
[ 2.081080] orion-ehci f1050000.usb-host: new USB bus registered, assigned bus number 1
[ 2.089429] orion-ehci f1050000.usb-host: irq 26, io mem 0xf1050000
[ 2.118232] orion-ehci f1050000.usb-host: USB 2.0 started, EHCI 1.00
[ 2.124853] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[ 2.133127] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.140361] usb usb1: Product: EHCI Host Controller
[ 2.145216] usb usb1: Manufacturer: Linux 4.18.5-mvebu-tld-1 ehci_hcd
[ 2.151668] usb usb1: SerialNumber: f1050000.usb-host
[ 2.157467] hub 1-0:1.0: USB hub found
[ 2.161450] hub 1-0:1.0: 1 port detected
[ 2.166133] orion-ehci f1051000.usb-host: EHCI Host Controller
[ 2.172248] orion-ehci f1051000.usb-host: new USB bus registered, assigned bus number 2
[ 2.180446] orion-ehci f1051000.usb-host: irq 27, io mem 0xf1051000
[ 2.201940] ata1: SATA link down (SStatus 0 SControl F300)
[ 2.208239] orion-ehci f1051000.usb-host: USB 2.0 started, EHCI 1.00
[ 2.214818] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[ 2.223101] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.230316] usb usb2: Product: EHCI Host Controller
[ 2.235175] usb usb2: Manufacturer: Linux 4.18.5-mvebu-tld-1 ehci_hcd
[ 2.241606] usb usb2: SerialNumber: f1051000.usb-host
[ 2.247340] hub 2-0:1.0: USB hub found
[ 2.251314] hub 2-0:1.0: 1 port detected
[ 2.256663] usbcore: registered new interface driver usblp
[ 2.262845] usbcore: registered new interface driver usb-storage
[ 2.269512] mousedev: PS/2 mouse device common for all mice
[ 2.276461] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time-clock as rtc0
[ 2.286343] i2c /dev entries driver
[ 2.289840] random: fast init done
[ 2.296338] orion_wdt: Initial timeout 25 sec
[ 2.304964] marvell-cesa f1030000.crypto-engine: CESA device successfully registered
[ 2.313408] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.319896] usbcore: registered new interface driver usbhid
[ 2.325443] usbhid: USB HID core driver
[ 2.330243] drop_monitor: Initializing network drop monitor service
[ 2.336938] NET: Registered protocol family 10
[ 2.352932] Segment Routing with IPv6
[ 2.356661] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.364716] NET: Registered protocol family 17
[ 2.369617] 8021q: 802.1Q VLAN Support v1.8
[ 2.373825] Key type dns_resolver registered
[ 2.378499] ThumbEE CPU extension supported.
[ 2.382761] Registering SWP/SWPB emulation handler
[ 2.388536] registered taskstats version 1
[ 2.392620] Loading compiled-in X.509 certificates
[ 2.397454] zswap: loaded using pool lzo/zbud
[ 2.418705] Key type big_key registered
[ 2.430246] Key type encrypted registered
[ 2.437205] rtc-mv f10d8500.real-time-clock: hctosys: unable to read the hardware clock
[ 2.448485] Freeing unused kernel memory: 1024K
[ 2.455050] Checked W+X mappings: passed, no W+X pages found
Loading, please wait...
[ 2.528311] usb 1-1: new high-speed USB device number 2 using orion-ehci
starting version 232
[ 2.571018] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 2.581839] random: udevadm: uninitialized urandom read (16 bytes read)
[ 2.589132] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 2.618298] usb 2-1: new high-speed USB device number 2 using orion-ehci
[ 2.740179] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98
[ 2.758318] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.765423] usb 1-1: Product: USB2.0 Hub
[ 2.786761] hub 1-1:1.0: USB hub found
[ 2.799323] hub 1-1:1.0: 4 ports detected
[ 2.840196] usb 2-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98
[ 2.858322] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.865430] usb 2-1: Product: USB2.0 Hub
[ 2.886313] hub 2-1:1.0: USB hub found
[ 2.899712] hub 2-1:1.0: 4 ports detected
[ 3.126858] i2c i2c-0: Added multiplexed i2c bus 1
[ 3.131783] usb 1-1.4: new high-speed USB device number 3 using orion-ehci
[ 3.177407] i2c i2c-0: Added multiplexed i2c bus 2
[ 3.185770] i2c i2c-0: Added multiplexed i2c bus 3
[ 3.309428] usb 1-1.4: New USB device found, idVendor=0781, idProduct=5530, bcdDevice= 1.26
[ 3.317770] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.338316] usb 1-1.4: Product: Cruzer
[ 3.342072] usb 1-1.4: Manufacturer: SanDisk
[ 3.346323] usb 1-1.4: SerialNumber: 20060775210A3B80C5B2
[ 3.356241] sdhci: Secure Digital Host Controller Interface driver
[ 3.367389] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 3.396108] scsi host1: usb-storage 1-1.4:1.0
[ 3.407326] sdhci: Copyright(c) Pierre Ossman
[ 3.425324] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.441104] mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
[ 3.491227] mmc0: SDHCI controller on f1090000.sdio-host [f1090000.sdio-host] using DMA
[ 3.513395] mmc1 bounce up to 128 segments into one, max segment size 65536 bytes
[ 3.568367] mmc1: SDHCI controller on f1092000.sdio-host [f1092000.sdio-host] using DMA
[ 3.621032] mmc1: new high speed MMC card at address 0001
[ 4.409900] scsi 1:0:0:0: Direct-Access SanDisk Cruzer 1.26 PQ: 0 ANSI: 5
[ 4.427722] sd 1:0:0:0: [sda] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB)
[ 4.442975] sd 1:0:0:0: [sda] Write Protect is off
[ 4.451627] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 4.479716] sda: sda1
[ 4.485341] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 4.624389] usbcore: registered new interface driver uas
[ 4.641273] mmcblk1: mmc1:0001 SEM02G 1.82 GiB
[ 4.646172] mmcblk1boot0: mmc1:0001 SEM02G partition 1 1.00 MiB
[ 4.677696] mmcblk1boot1: mmc1:0001 SEM02G partition 2 1.00 MiB
[ 4.685285] mmcblk1rpmb: mmc1:0001 SEM02G partition 3 128 KiB, chardev (242:0)
[ 4.706573] mmcblk1: p1 p2 p3
[ 4.710327] mmcblk1: p3 size 1831410 extends beyond EOD, truncated
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.29.2
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1
rootfs: clean, 26714/488640 files, 378695/1953536 blocks
done.
[ 15.256130] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 15.285076] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Setting hostname to 'debian'...done.
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
. ok
[ ok ] Synthesizing the initial hotplug events...done.
[....] Waiting for /dev to be fully populated...[ 18.120391] sd 1:0:0:0: Attached scsi generic sg0 type 0
done.
[ ok ] Activating swap:.
[ 20.701039] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 20.715092] random: crng init done
[ 20.718486] random: 7 urandom warning(s) missed due to ratelimiting
[ ok ] Will now activate lvm and md swap:done.
[info] Will now check all file systems.
fsck from util-linux 2.29.2
Checking all file systems.
LABEL=rootfs is mounted
[ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables...done.
[ ok ] Initializing random number generator...done.
[ 23.609178] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 25.961307] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 25.971146] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5
Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:05:35:09:92:9a
Sending on LPF/eth0/00:05:35:09:92:9a
Sending on Socket/fallback
DHCPREQUEST of 192.168.1.135 on eth0 to 255.255.255.255 port 67
DHCPREQUEST of 192.168.1.135 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.1.135 from 192.168.1.1
bound to 192.168.1.135 -- renewal in 18087 seconds.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
[ ok ] Setting up ALSA...done (none loaded).
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2571 (syslogd)
. ok
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting periodic command scheduler: cron.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2572 (klogd)
. ok
[ ok ] Starting system message bus: dbus.
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Running local boot scripts (/etc/rc.local).
Debian GNU/Linux 9 debian ttyS0
debian login: root
Password:
Last login: Mon Oct 1 15:24:23 PDT 2018 from 192.168.1.2 on pts/0
Linux debian 4.18.5-mvebu-tld-1 #1 SMP PREEMPT Thu Aug 30 22:19:21 PDT 2018 armv7l
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
debian
192.168.1.135
Chip PC LXD8941
Linux version 4.18.5-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9)) #1 SMP PREEMPT Thu Aug 30 22:19:21 PDT 2018
Debian 9.5
Mon Oct 1 16:20:00 PDT 2018 up 1 minute
root@debian:~#
root@debian:~# lsmod Module Size Used by armada 45056 0 drm_kms_helper 114688 1 armada drm 294912 2 armada,drm_kms_helper drm_panel_orientation_quirks 16384 1 drm fb_sys_fops 16384 1 drm_kms_helper syscopyarea 16384 1 drm_kms_helper sysfillrect 16384 1 drm_kms_helper sysimgblt 16384 1 drm_kms_helper cfbfillrect 16384 1 drm_kms_helper cfbimgblt 16384 1 drm_kms_helper cfbcopyarea 16384 1 drm_kms_helper sg 32768 0 uio_pdrv_genirq 16384 0 uio 20480 1 uio_pdrv_genirq mmc_block 36864 0 uas 20480 0 sdhci_dove 16384 0 sdhci_pltfm 16384 1 sdhci_dove sdhci 49152 2 sdhci_dove,sdhci_pltfm mmc_core 122880 3 sdhci_dove,sdhci,mmc_block i2c_mux_pinctrl 16384 0 root@debian:~#
|
Re: Chip PC LXD8941 October 01, 2018 07:50PM |
Admin Registered: 13 years ago Posts: 19,192 |
It does work now! list the partition.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
fdisk -l
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Chip PC LXD8941 October 01, 2018 07:54PM |
Admin Registered: 13 years ago Posts: 19,192 |
Does this box have both internal SD and external SD slot?
There is a 1.82GB SD card that was detected by the kernel in the log.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 10/01/2018 07:56PM by bodhi.
There is a 1.82GB SD card that was detected by the kernel in the log.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 10/01/2018 07:56PM by bodhi.
|
Re: Chip PC LXD8941 October 02, 2018 02:00AM |
Registered: 6 years ago Posts: 183 |
|
Re: Chip PC LXD8941 October 02, 2018 02:52AM |
Admin Registered: 13 years ago Posts: 19,192 |
Ok. Here is the new DTB with mmc 0.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Chip PC LXD8941 October 02, 2018 01:03PM |
Registered: 6 years ago Posts: 183 |
This latest .dtb file doesn't fix mmc0 but makes mmc1 disappear as well :-)
Koen
Koen
MIC>> setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 ${mtdparts} earlyprintk=serial'
MIC>> setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x3000000 /boot/uImage; ext2load usb 0:1 0x4000000 /boot/uInitrd'
MIC>> setenv bootcmd_exec 'run set_bootargs; run bootcmd_usb; bootm 0x3000000 0x4000000'
MIC>> run bootcmd_exec
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
......
......
............
.........................
...................................................
......................................................................................................
............................................................................................................................................................................................................
..........................
4465752 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
......
......
............
.........................
...................................................
......................................................................................................
......................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
................................
8721585 bytes read
## Booting kernel from Legacy Image at 03000000 ...
Image Name: Linux-4.18.5-mvebu-tld-1
Created: 2018-10-02 17:47:49 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4465688 Bytes = 4.3 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 04000000 ...
Image Name: initramfs-4.18.5-mvebu-tld-1
Created: 2018-09-29 17:33:30 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 8721521 Bytes = 8.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
EUGENE lcd_disable
EUGENE lcd_panel_disable
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.18.5-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9)) #1 SMP PREEMPT Thu Aug 30 22:19:21 PDT 2018
[ 0.000000] CPU: ARMv7 Processor [413fc081] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Chip PC LXD8941
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] random: get_random_bytes called from start_kernel+0x78/0x4c4 with crng_init=0
[ 0.000000] percpu: Embedded 18 pages/cpu @(ptrval) s41548 r8192 d23988 u73728
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi0.0:768k(uboot),256k(uboot_env),768k(uboot2),-(kernel) earlyprintk=serial
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1016480K/1048576K available (9216K kernel code, 790K rwdata, 2304K rodata, 1024K init, 327K bss, 32096K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (10208 kB)
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 791 kB)
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 328 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.18.5-mvebu-tld-1 #1
[ 0.000000] Hardware name: Marvell Dove
[ 0.000000] [<c0117d00>] (unwind_backtrace) from [<c0112680>] (show_stack+0x10/0x14)
[ 0.000000] [<c0112680>] (show_stack) from [<c0944f18>] (dump_stack+0x70/0x8c)
[ 0.000000] [<c0944f18>] (dump_stack) from [<c0943574>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c0943574>] (Ldiv0) from [<c05c2fbc>] (dove_recalc_rate+0x44/0x8c)
[ 0.000000] [<c05c2fbc>] (dove_recalc_rate) from [<c05bed1c>] (clk_register+0x40c/0x5d4)
[ 0.000000] [<c05bed1c>] (clk_register) from [<c0d35580>] (dove_divider_clk_init+0x12c/0x190)
[ 0.000000] [<c0d35580>] (dove_divider_clk_init) from [<c0d353c8>] (dove_clk_init+0x4c/0x74)
[ 0.000000] [<c0d353c8>] (dove_clk_init) from [<c0d3353c>] (of_clk_init+0x184/0x240)
[ 0.000000] [<c0d3353c>] (of_clk_init) from [<c0d04004>] (time_init+0x20/0x2c)
[ 0.000000] [<c0d04004>] (time_init) from [<c0d00d14>] (start_kernel+0x2f8/0x4c4)
[ 0.000000] [<c0d00d14>] (start_kernel) from [<00000000>] ( (null))
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[ 0.000007] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[ 0.007824] Switching to timer-based delay loop, resolution 6ns
[ 0.014457] Console: colour dummy device 80x30
[ 0.018955] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[ 0.029472] pid_max: default: 32768 minimum: 301
[ 0.034310] Security Framework initialized
[ 0.038543] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.045145] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.053177] CPU: Testing write buffer coherency: ok
[ 0.058115] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[ 0.067932] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.127982] Setting up static identity map for 0x100000 - 0x100060
[ 0.134921] Hierarchical SRCU implementation.
[ 0.177882] smp: Bringing up secondary CPUs ...
[ 0.182398] smp: Brought up 1 node, 1 CPU
[ 0.186388] SMP: Total of 1 processors activated (333.33 BogoMIPS).
[ 0.192684] CPU: All CPU(s) started in SVC mode.
[ 0.198299] devtmpfs: initialized
[ 0.208121] VFP support v0.3: implementor 41 architecture 2 part 20 variant 9 rev 5
[ 0.216539] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.226727] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.233223] prandom: seed boundary self test passed
[ 0.241406] prandom: 100 self tests passed
[ 0.245487] pinctrl core: initialized pinctrl subsystem
[ 0.253317] NET: Registered protocol family 16
[ 0.259604] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.266984] audit: initializing netlink subsys (disabled)
[ 0.274943] audit: type=2000 audit(0.260:1): state=initialized audit_enabled=0 res=1
[ 0.298171] cpuidle: using governor ladder
[ 0.302381] cpuidle: using governor menu
[ 0.306522] Dove 88AP510 SoC
[ 0.309521] Tauros2: Disabling L2 prefetch.
[ 0.313688] Tauros2: Disabling burst8 line fill.
[ 0.318399] Tauros2: Enabling L2 cache.
[ 0.322217] Tauros2: L2 cache support initialised in ARMv7 mode.
[ 0.328617] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.428831] vgaarb: loaded
[ 0.431868] SCSI subsystem initialized
[ 0.438354] usbcore: registered new interface driver usbfs
[ 0.443863] usbcore: registered new interface driver hub
[ 0.450328] usbcore: registered new device driver usb
[ 0.456118] media: Linux media interface: v0.10
[ 0.461231] videodev: Linux video capture interface: v2.00
[ 0.467228] pps_core: LinuxPPS API ver. 1 registered
[ 0.472598] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.481916] PTP clock support registered
[ 0.488207] clocksource: Switched to clocksource orion_clocksource
[ 0.581342] VFS: Disk quotas dquot_6.6.0
[ 0.585323] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.612659] NET: Registered protocol family 2
[ 0.618922] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.626560] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.633998] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.640556] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.646992] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.652991] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.659583] NET: Registered protocol family 1
[ 0.694619] RPC: Registered named UNIX socket transport module.
[ 0.700582] RPC: Registered udp transport module.
[ 0.705261] RPC: Registered tcp transport module.
[ 0.709980] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.716615] Unpacking initramfs...
[ 1.272699] Freeing initrd memory: 8520K
[ 1.276812] NetWinder Floating Point Emulator V0.97 (double precision)
[ 1.286023] Initialise system trusted keyrings
[ 1.291535] Key type blacklist registered
[ 1.295722] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 1.302333] zbud: loaded
[ 1.315902] NFS: Registering the id_resolver key type
[ 1.321146] Key type id_resolver registered
[ 1.325310] Key type id_legacy registered
[ 1.329374] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.336042] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.342698] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.350311] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 1.356901] orangefs_init: module version upstream loaded
[ 1.368976] Key type asymmetric registered
[ 1.373057] Asymmetric key parser 'x509' registered
[ 1.377981] bounce: pool size: 64 pages
[ 1.382048] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 1.389739] io scheduler noop registered
[ 1.393645] io scheduler deadline registered
[ 1.397960] io scheduler cfq registered (default)
[ 1.404948] dove-pinctrl f10d0200.pin-ctrl: falling back to hardcoded PMU resource
[ 1.413547] dove-pinctrl f10d0200.pin-ctrl: [Firmware Bug]: Missing pinctrl regs in DTB. Please update your firmware.
[ 1.424882] dove-pinctrl f10d0200.pin-ctrl: registered pinctrl driver
[ 1.436436] mvebu-pcie mbus:pcie: PCI host bridge to bus 0000:00
[ 1.443517] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 1.449920] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 1.456765] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.464367] PCI: bus0: Fast back to back transfers disabled
[ 1.470148] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.478129] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.487552] PCI: bus1: Fast back to back transfers enabled
[ 1.494594] PCI: bus2: Fast back to back transfers enabled
[ 1.500242] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 1.505190] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 1.511319] mv_xor f1060800.dma-engine: Marvell shared XOR driver
[ 1.579336] mv_xor f1060800.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 1.587617] mv_xor f1060900.dma-engine: Marvell shared XOR driver
[ 1.649322] mv_xor f1060900.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 1.790719] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.800999] console [ttyS0] disabled
[ 1.805279] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 21, base_baud = 10416666) is a 16550A
[ 1.814532] console [ttyS0] enabled
[ 1.814532] console [ttyS0] enabled
[ 1.821657] bootconsole [earlycon0] disabled
[ 1.821657] bootconsole [earlycon0] disabled
[ 1.831386] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 22, base_baud = 10416666) is a 16550A
[ 1.842527] sata_mv f10a0000.sata-host: slots 32 ports 1
[ 1.860169] scsi host0: sata_mv
[ 1.863850] ata1: SATA max UDMA/133 irq 33
[ 1.870153] m25p80 spi0.0: found mx25l1606e, expected sst25vf080b
[ 1.876233] m25p80 spi0.0: mx25l1606e (2048 Kbytes)
[ 1.882525] 4 cmdlinepart partitions found on MTD device spi0.0
[ 1.888485] Creating 4 MTD partitions on "spi0.0":
[ 1.893260] 0x000000000000-0x0000000c0000 : "uboot"
[ 1.899623] 0x0000000c0000-0x000000100000 : "uboot_env"
[ 1.906410] 0x000000100000-0x0000001c0000 : "uboot2"
[ 1.913130] 0x0000001c0000-0x000000200000 : "kernel"
[ 1.922432] libphy: Fixed MDIO Bus: probed
[ 1.930301] libphy: orion_mdio_bus: probed
[ 1.942224] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 2.049553] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:05:35:09:92:9a
[ 2.059394] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.065910] ehci-pci: EHCI PCI platform driver
[ 2.070918] ehci-orion: EHCI orion driver
[ 2.075081] orion-ehci f1050000.usb-host: EHCI Host Controller
[ 2.081057] orion-ehci f1050000.usb-host: new USB bus registered, assigned bus number 1
[ 2.089486] orion-ehci f1050000.usb-host: irq 26, io mem 0xf1050000
[ 2.118243] orion-ehci f1050000.usb-host: USB 2.0 started, EHCI 1.00
[ 2.124865] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[ 2.133146] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.140377] usb usb1: Product: EHCI Host Controller
[ 2.145234] usb usb1: Manufacturer: Linux 4.18.5-mvebu-tld-1 ehci_hcd
[ 2.151686] usb usb1: SerialNumber: f1050000.usb-host
[ 2.157476] hub 1-0:1.0: USB hub found
[ 2.161456] hub 1-0:1.0: 1 port detected
[ 2.166148] orion-ehci f1051000.usb-host: EHCI Host Controller
[ 2.172265] orion-ehci f1051000.usb-host: new USB bus registered, assigned bus number 2
[ 2.180456] orion-ehci f1051000.usb-host: irq 27, io mem 0xf1051000
[ 2.201947] ata1: SATA link down (SStatus 0 SControl F300)
[ 2.208249] orion-ehci f1051000.usb-host: USB 2.0 started, EHCI 1.00
[ 2.214828] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18
[ 2.223111] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.230327] usb usb2: Product: EHCI Host Controller
[ 2.235185] usb usb2: Manufacturer: Linux 4.18.5-mvebu-tld-1 ehci_hcd
[ 2.241614] usb usb2: SerialNumber: f1051000.usb-host
[ 2.247359] hub 2-0:1.0: USB hub found
[ 2.251330] hub 2-0:1.0: 1 port detected
[ 2.256678] usbcore: registered new interface driver usblp
[ 2.262854] usbcore: registered new interface driver usb-storage
[ 2.269517] mousedev: PS/2 mouse device common for all mice
[ 2.276467] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time-clock as rtc0
[ 2.286342] i2c /dev entries driver
[ 2.289840] random: fast init done
[ 2.296342] orion_wdt: Initial timeout 25 sec
[ 2.304952] marvell-cesa f1030000.crypto-engine: CESA device successfully registered
[ 2.313398] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.319889] usbcore: registered new interface driver usbhid
[ 2.325435] usbhid: USB HID core driver
[ 2.330229] drop_monitor: Initializing network drop monitor service
[ 2.336922] NET: Registered protocol family 10
[ 2.352917] Segment Routing with IPv6
[ 2.356643] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.364692] NET: Registered protocol family 17
[ 2.369590] 8021q: 802.1Q VLAN Support v1.8
[ 2.373800] Key type dns_resolver registered
[ 2.378493] ThumbEE CPU extension supported.
[ 2.382752] Registering SWP/SWPB emulation handler
[ 2.388520] registered taskstats version 1
[ 2.392603] Loading compiled-in X.509 certificates
[ 2.397439] zswap: loaded using pool lzo/zbud
[ 2.418649] Key type big_key registered
[ 2.430294] Key type encrypted registered
[ 2.437277] rtc-mv f10d8500.real-time-clock: setting system clock to 2018-10-02 17:49:56 UTC (1538502596)
[ 2.450051] Freeing unused kernel memory: 1024K
[ 2.456613] Checked W+X mappings: passed, no W+X pages found
Loading, please wait...
[ 2.528319] usb 1-1: new high-speed USB device number 2 using orion-ehci
starting version 232
[ 2.570966] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 2.583994] random: udevadm: uninitialized urandom read (16 bytes read)
[ 2.591249] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 2.618303] usb 2-1: new high-speed USB device number 2 using orion-ehci
[ 2.740236] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98
[ 2.758328] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.765440] usb 1-1: Product: USB2.0 Hub
[ 2.786691] hub 1-1:1.0: USB hub found
[ 2.799345] hub 1-1:1.0: 4 ports detected
[ 2.840206] usb 2-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98
[ 2.858331] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.865439] usb 2-1: Product: USB2.0 Hub
[ 2.886174] hub 2-1:1.0: USB hub found
[ 2.899723] hub 2-1:1.0: 4 ports detected
[ 3.126798] i2c i2c-0: Added multiplexed i2c bus 1
[ 3.131726] usb 1-1.4: new high-speed USB device number 3 using orion-ehci
[ 3.176934] i2c i2c-0: Added multiplexed i2c bus 2
[ 3.197130] i2c i2c-0: Added multiplexed i2c bus 3
[ 3.285246] sdhci: Secure Digital Host Controller Interface driver
[ 3.299479] usb 1-1.4: New USB device found, idVendor=0781, idProduct=5530, bcdDevice= 1.26
[ 3.307825] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.326919] sdhci: Copyright(c) Pierre Ossman
[ 3.331326] usb 1-1.4: Product: Cruzer
[ 3.335070] usb 1-1.4: Manufacturer: SanDisk
[ 3.346939] usb 1-1.4: SerialNumber: 20060775210A3B80C5B2
[ 3.357301] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 3.364501] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.384270] mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
[ 3.391861] scsi host1: usb-storage 1-1.4:1.0
[ 3.445672] mmc0: SDHCI controller on f1090000.sdio-host [f1090000.sdio-host] using DMA
[ 3.468289] sdhci-dove f1092000.sdio-host: Got CD GPIO
[ 3.473569] mmc1 bounce up to 128 segments into one, max segment size 65536 bytes
[ 3.548569] mmc1: SDHCI controller on f1092000.sdio-host [f1092000.sdio-host] using DMA
[ 4.409958] scsi 1:0:0:0: Direct-Access SanDisk Cruzer 1.26 PQ: 0 ANSI: 5
[ 4.427283] sd 1:0:0:0: [sda] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB)
[ 4.444162] sd 1:0:0:0: [sda] Write Protect is off
[ 4.453286] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 4.482272] sda: sda1
[ 4.487898] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 4.603575] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.29.2
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1
rootfs: clean, 26714/488640 files, 378698/1953536 blocks
done.
[ 15.056064] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 15.084859] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Setting hostname to 'debian'...done.
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
. ok
[ ok ] Synthesizing the initial hotplug events...done.
[....] Waiting for /dev to be fully populated...[ 17.901913] sd 1:0:0:0: Attached scsi generic sg0 type 0
done.
[ ok ] Activating swap:.
[ 20.300670] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ ok ] Will now activate lvm and md swap:done.
[info] Will now check all file systems.
fsck from util-linux 2.29.2
Checking all file systems.
LABEL=rootfs is mounted
[ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ 21.688304] random: crng init done
[ 21.691704] random: 7 urandom warning(s) missed due to ratelimiting
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables...done.
[ ok ] Initializing random number generator...done.
[ 23.209216] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 25.550301] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 25.560143] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5
Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:05:35:09:92:9a
Sending on LPF/eth0/00:05:35:09:92:9a
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9
DHCPREQUEST of 192.168.1.135 on eth0 to 255.255.255.255 port 67
DHCPOFFER of 192.168.1.135 from 192.168.1.1
DHCPACK of 192.168.1.135 from 192.168.1.1
bound to 192.168.1.135 -- renewal in 17966 seconds.
done.
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
[ ok ] Setting up ALSA...done (none loaded).
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2564 (syslogd)
. ok
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2565 (klogd)
. ok
[ ok ] Starting NTP server: ntpd.
[ ok ] Running local boot scripts (/etc/rc.local).
Debian GNU/Linux 9 debian ttyS0
debian login: root
Password:
Last login: Tue Oct 2 10:42:42 PDT 2018 from 192.168.1.2 on pts/0
Linux debian 4.18.5-mvebu-tld-1 #1 SMP PREEMPT Thu Aug 30 22:19:21 PDT 2018 armv7l
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
debian
192.168.1.135
Chip PC LXD8941
Linux version 4.18.5-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9)) #1 SMP PREEMPT Thu Aug 30 22:19:21 PDT 2018
Debian 9.5
Tue Oct 2 10:50:51 PDT 2018 up
root@debian:~#
root@debian:~# lsmod Module Size Used by armada 45056 0 drm_kms_helper 114688 1 armada drm 294912 2 armada,drm_kms_helper drm_panel_orientation_quirks 16384 1 drm fb_sys_fops 16384 1 drm_kms_helper syscopyarea 16384 1 drm_kms_helper sysfillrect 16384 1 drm_kms_helper sysimgblt 16384 1 drm_kms_helper cfbfillrect 16384 1 drm_kms_helper cfbimgblt 16384 1 drm_kms_helper cfbcopyarea 16384 1 drm_kms_helper sg 32768 0 uio_pdrv_genirq 16384 0 uio 20480 1 uio_pdrv_genirq uas 20480 0 sdhci_dove 16384 0 sdhci_pltfm 16384 1 sdhci_dove sdhci 49152 2 sdhci_dove,sdhci_pltfm mmc_core 122880 2 sdhci_dove,sdhci i2c_mux_pinctrl 16384 0 root@debian:~#
root@debian:~# modprobe mmc_block root@debian:~# root@debian:~# cat /proc/partitions major minor #blocks name 31 0 768 mtdblock0 31 1 256 mtdblock1 31 2 768 mtdblock2 31 3 256 mtdblock3 8 0 7816704 sda 8 1 7814144 sda1 root@debian:~#
|
Re: Chip PC LXD8941 October 02, 2018 01:05PM |
Admin Registered: 13 years ago Posts: 19,192 |
Koen,
> This latest .dtb file doesn't fix mmc0 but makes
> mmc1 disappear as well :-)
:) that proved the GPIO 12 is for mmc 1, for sure.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> This latest .dtb file doesn't fix mmc0 but makes
> mmc1 disappear as well :-)
:) that proved the GPIO 12 is for mmc 1, for sure.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Chip PC LXD8941 October 02, 2018 01:12PM |
Admin Registered: 13 years ago Posts: 19,192 |
Now we need to find where this is done in GPL. It is some where between 40 and 45.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
+ { 40, MPP_SDIO0 }, /* will configure MPPs 40-45 */
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Chip PC LXD8941 October 02, 2018 03:25PM |
Registered: 6 years ago Posts: 183 |
Hi bodhi,
I've had another look through the Dell Wyse Ubuntu files and found some more stuff related to SD card in the file 'dove-rd-avng-setup.c'.
There is a section called 'Board Init' which includes some SD card setup calls:
Trawling through some of the other files I have found the 'dove_sd_card_int_wa_setup' function in 'common.c'
I'm not sure if this is what is needed to activate the sd card slot but I thought I would share it anyway.
Koen
Edited 1 time(s). Last edit at 10/02/2018 03:29PM by Koen.
I've had another look through the Dell Wyse Ubuntu files and found some more stuff related to SD card in the file 'dove-rd-avng-setup.c'.
There is a section called 'Board Init' which includes some SD card setup calls:
/*****************************************************************************
* Board Init
****************************************************************************/
static void __init dove_rd_avng_init(void)
{
u32 dev, rev;
/*
* Basic Dove setup. Needs to be called early.
*/
dove_init();
dove_pcie_id(&dev, &rev);
if (rev >= DOVE_REV_X0)
dove_mpp_conf(dove_rd_avng_x0_mpp_modes);
else
dove_mpp_conf(dove_rd_avng_y0_mpp_modes);
dove_rd_avng_gpio_init(rev);
pm_power_off = dove_rd_avng_power_off;
/* sdio card interrupt workaround using GPIOs */
dove_sd_card_int_wa_setup(0);
dove_sd_card_int_wa_setup(1);
Trawling through some of the other files I have found the 'dove_sd_card_int_wa_setup' function in 'common.c'
/*****************************************************************************
* SDIO
****************************************************************************/
#define DOVE_SD0_START_GPIO 40
#define DOVE_SD1_START_GPIO 46
struct sdhci_dove_int_wa sdio0_data = {
.gpio = DOVE_SD0_START_GPIO + 3,
.func_select_bit = 0
};
static u64 sdio_dmamask = DMA_BIT_MASK(32);
/*****************************************************************************
* SDIO0
****************************************************************************/
static struct resource dove_sdio0_resources[] = {
{
.start = DOVE_SDIO0_PHYS_BASE,
.end = DOVE_SDIO0_PHYS_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
}, {
.start = IRQ_DOVE_SDIO0,
.end = IRQ_DOVE_SDIO0,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device dove_sdio0 = {
.name = "sdhci-mv",
.id = 0,
.dev = {
.dma_mask = &sdio_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
},
.resource = dove_sdio0_resources,
.num_resources = ARRAY_SIZE(dove_sdio0_resources),
};
void __init dove_sdio0_init(void)
{
platform_device_register(&dove_sdio0);
}
/*****************************************************************************
* SDIO1
****************************************************************************/
struct sdhci_dove_int_wa sdio1_data = {
.gpio = DOVE_SD1_START_GPIO + 3,
.func_select_bit = 1
};
static struct resource dove_sdio1_resources[] = {
{
.start = DOVE_SDIO1_PHYS_BASE,
.end = DOVE_SDIO1_PHYS_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
}, {
.start = IRQ_DOVE_SDIO1,
.end = IRQ_DOVE_SDIO1,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device dove_sdio1 = {
.name = "sdhci-mv",
.id = 1,
.dev = {
.dma_mask = &sdio_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
},
.resource = dove_sdio1_resources,
.num_resources = ARRAY_SIZE(dove_sdio1_resources),
};
void __init dove_sdio1_init(void)
{
platform_device_register(&dove_sdio1);
}
/* sdio card interrupt workaround, when no command is running, switch the
* DATA[1] pin to be gpio-in with level interrupt.
*/
void __init dove_sd_card_int_wa_setup(int port)
{
int gpio = 0, i, irq = 0;
char *name;
switch(port) {
case 0:
gpio = DOVE_SD0_START_GPIO;
name = "sd0";
dove_sdio0.dev.platform_data = &sdio0_data;
irq = sdio0_data.irq = gpio_to_irq(sdio0_data.gpio);
break;
case 1:
gpio = DOVE_SD1_START_GPIO;
name = "sd1";
dove_sdio1.dev.platform_data = &sdio1_data;
irq = sdio1_data.irq = gpio_to_irq(sdio1_data.gpio);
break;
default:
printk(KERN_ERR "dove_sd_card_int_wa_setup: bad port (%d)\n",
port);
return;
}
for (i = gpio; i < (gpio + 6); i++) {
orion_gpio_set_valid(i, 1);
if (gpio_request(i, name) != 0)
printk(KERN_ERR "dove: failed to config gpio (%d) for %s\n",
i, name);
gpio_direction_input(i);
}
set_irq_type(irq, IRQ_TYPE_LEVEL_LOW);
}
I'm not sure if this is what is needed to activate the sd card slot but I thought I would share it anyway.
Koen
Edited 1 time(s). Last edit at 10/02/2018 03:29PM by Koen.
|
Re: Chip PC LXD8941 October 03, 2018 12:02AM |
Admin Registered: 13 years ago Posts: 19,192 |
Koen,
Yeah. Looks like they had some problem, and had to work around it. It is consisten with the comment,
I was too distracted about on SDIO1 and GPO 12! We'll try 40.
And BTW, what you did above was good (trying to use import/export GPIO to manipulate the bits in class devices in Debian).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 10/03/2018 12:04AM by bodhi.
Yeah. Looks like they had some problem, and had to work around it. It is consisten with the comment,
Quote
+ { 40, MPP_SDIO0 }, /* will configure MPPs 40-45 */
I was too distracted about on SDIO1 and GPO 12! We'll try 40.
And BTW, what you did above was good (trying to use import/export GPIO to manipulate the bits in class devices in Debian).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 10/03/2018 12:04AM by bodhi.
|
Re: Chip PC LXD8941 October 03, 2018 12:38AM |
Admin Registered: 13 years ago Posts: 19,192 |
Ok let's try this version.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Chip PC LXD8941 October 14, 2018 07:41AM |
Registered: 6 years ago Posts: 183 |
I've tried this latest dtb but can't get the SD card to show up so I've reverted back to the .dtb from 26 September. I've cloned the USB stick to a SD card and plugged it into the device. I then change uboot environment from serial using the following commands:
This boots into Debian from the SD card however it is not very responsive probably due to the low quality (class 4) card. The stock system doesn't offer a terminal or ssh access so I'm thinking of wiping the internal memory and installing Debian there.
The device has 2GB of internal memory divided into 3 partitions:
mmcblk1p1 seems to be a FAT file system that doesn't mount in Debian. Probably best to leave it in place.
mmcblk1p2 is an ext3 filesystem with the following contents:
tffsb is an image that is loaded by uboot during boot to display on the screen, tffsd and tffsf contain data, tffsg is the uImage and tffsh & tffsi are identical squashfs filesystems.
mmcblk1p3 is an ext3 filesystem with the following contents:
So I'm thinking of removing the uImage and squashfs files from partition 2 but leave the three small files in place. I would then resize partition 2 to its minimal required size, wipe the contents of partition 3 and resizing it to the maximum size and install Debian in there.
Koen
setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 ${mtdparts} earlyprintk=serial'
setenv bootcmd_sd 'mmcinfo 1; ext2load mmc 1:1 0x3000000 /boot/uImage; ext2load mmc 1:1 0x4000000 /boot/uInitrd'
setenv bootcmd_exec 'run set_bootargs; run bootcmd_sd; bootm 0x3000000 0x4000000'
run bootcmd_exec
This boots into Debian from the SD card however it is not very responsive probably due to the low quality (class 4) card. The stock system doesn't offer a terminal or ssh access so I'm thinking of wiping the internal memory and installing Debian there.
The device has 2GB of internal memory divided into 3 partitions:
root@debian:~# cat /proc/partitions major minor #blocks name 31 0 768 mtdblock0 31 1 256 mtdblock1 31 2 768 mtdblock2 31 3 256 mtdblock3 8 0 7816704 sda 8 1 7814144 sda1 179 0 1912832 mmcblk1 179 1 8001 mmcblk1p1 179 2 1028160 mmcblk1p2 179 3 876639 mmcblk1p3
mmcblk1p1 seems to be a FAT file system that doesn't mount in Debian. Probably best to leave it in place.
mmcblk1p2 is an ext3 filesystem with the following contents:
root@debian:/mnt/temp# ll total 320036 drwxr-xr-x 3 root root 4096 Sep 22 00:49 . drwxr-xr-x 3 root root 4096 Sep 22 00:48 .. drwx------ 2 root root 16384 Feb 4 1930 lost+found -rw-r--r-- 1 root root 787508 Jul 21 2013 tffsb -rw-r--r-- 1 root root 524288 Oct 15 2000 tffsd -rw-r--r-- 1 root root 80 Dec 31 2012 tffsf -rw-r--r-- 1 root root 14119164 Jan 21 2014 tffsg -rw-r--r-- 1 root root 155951104 Feb 2 2014 tffsh -rw-r--r-- 1 root root 155951104 Feb 2 2014 tffsi root@debian:/mnt/temp#
tffsb is an image that is loaded by uboot during boot to display on the screen, tffsd and tffsf contain data, tffsg is the uImage and tffsh & tffsi are identical squashfs filesystems.
mmcblk1p3 is an ext3 filesystem with the following contents:
root@debian:/mnt/temp# ll total 56 drwxr-xr-x 11 root root 4096 May 18 2016 . drwxr-xr-x 3 root root 4096 Sep 22 00:48 .. -r--r--r-- 3 root root 0 May 18 2016 .wh..wh.aufs drwx------ 2 root root 4096 May 18 2016 .wh..wh.orph drwx------ 2 root root 4096 May 18 2016 .wh..wh.plnk drwxr-xr-x 2 root root 4096 May 18 2016 doc drwxr-xr-x 9 root root 4096 Dec 31 2012 etc drwxrwxrwx 3 root root 4096 Jan 14 2014 lib drwx------ 2 root root 16384 May 18 2016 lost+found drwxr-xr-x 12 root root 4096 Dec 31 2012 root drwxr-xr-x 4 root root 4096 May 18 2016 usr drwxr-xr-x 5 root root 4096 Jan 2 2013 var root@debian:/mnt/temp# du -lsh . 15M . root@debian:/mnt/temp#
So I'm thinking of removing the uImage and squashfs files from partition 2 but leave the three small files in place. I would then resize partition 2 to its minimal required size, wipe the contents of partition 3 and resizing it to the maximum size and install Debian in there.
Koen
|
Re: Chip PC LXD8941 October 14, 2018 10:40AM |
Registered: 6 years ago Posts: 183 |
OK the steps above have worked. I've created backups of the original partitions to an external drive and removed most of the files. Then I've resized the filesystem and partition mmcblk1p2. I've removed the old mmcblk1p3 partition and re-created it with the rootfs label. Then I used the following commands in serial to boot from the internal memory:
new partition layout:
More than 1GB of free space on a clean 4.12 rootfs install:
Koen
setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 ${mtdparts} earlyprintk=serial'
setenv bootcmd_int 'mmcinfo 0; ext2load mmc 0:3 0x3000000 /boot/uImage; ext2load mmc 0:3 0x4000000 /boot/uInitrd'
setenv bootcmd_exec 'run set_bootargs; run bootcmd_int; bootm 0x3000000 0x4000000'
run bootcmd_exec
new partition layout:
root@debian:/# cat /proc/partitions major minor #blocks name 31 0 768 mtdblock0 31 1 256 mtdblock1 31 2 768 mtdblock2 31 3 256 mtdblock3 179 0 1912832 mmcblk1 179 1 8001 mmcblk1p1 179 2 21264 mmcblk1p2 179 3 1883136 mmcblk1p3 179 24 128 mmcblk1rpmb 179 16 1024 mmcblk1boot1 179 8 1024 mmcblk1boot0 root@debian:/#
More than 1GB of free space on a clean 4.12 rootfs install:
root@debian:/# df -h Filesystem Size Used Avail Use% Mounted on udev 498M 0 498M 0% /dev tmpfs 101M 1.2M 100M 2% /run /dev/mmcblk1p3 1.8G 595M 1.1G 36% / tmpfs 5.0M 0 5.0M 0% /run/lock tmpfs 201M 0 201M 0% /run/shm tmpfs 502M 0 502M 0% /tmp root@debian:/#
Koen
|
Re: Chip PC LXD8941 October 14, 2018 04:16PM |
Admin Registered: 13 years ago Posts: 19,192 |
Hi Koen,
Good works! I have been busy so can only resond to posts. No time to research much.
Usually we do "mmc reset" here.
Another observation. Why didn't you just wipe out the internal SD and make 1 partition? if you are not going to use stock as rescue then why keeping multiple partitions?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Good works! I have been busy so can only resond to posts. No time to research much.
Usually we do "mmc reset" here.
Quote
setenv bootcmd_int 'mmcinfo 0; ext2load mmc 0:3 0x3000000 /boot/uImage; ext2load mmc 0:3 0x4000000 /boot/uInitrd'
Another observation. Why didn't you just wipe out the internal SD and make 1 partition? if you are not going to use stock as rescue then why keeping multiple partitions?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Chip PC LXD8941 October 14, 2018 05:08PM |
Registered: 6 years ago Posts: 183 |
Hi bodhi,
stock uboot loads an image from the 2nd partition to display on screen during boot. I can't find it anywhere in the uboot environment variables so I assume that this behavior is hard coded. This happens before you get to the uboot prompt so I am afraid that removing the 2nd partition may result in a brick. The 1st partition can't be mounted in Debian so I'm not sure what is stored in there. In the end the size of the 1st and 2nd partitions is now small enough that I don't care too much about the wasted space.
Koen
stock uboot loads an image from the 2nd partition to display on screen during boot. I can't find it anywhere in the uboot environment variables so I assume that this behavior is hard coded. This happens before you get to the uboot prompt so I am afraid that removing the 2nd partition may result in a brick. The 1st partition can't be mounted in Debian so I'm not sure what is stored in there. In the end the size of the 1st and 2nd partitions is now small enough that I don't care too much about the wasted space.
Koen
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2009.08-svn7881 (Jan 23 2013 - 13:55:26) version: dove-5.3.4
BootROM:
Version on chip: 2.33
Status: OK
Retries #: 0
Board: RD-88AP510-Avengers
SoC: MV88F510 Rev 7
CPU: ??? (0x0c08) (Rev 1)
CPU @ 933Mhz, L2 @ 466Mhz
DDR3 @ 466Mhz, TClock @ 166Mhz
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Write Leveling Results:
CS0, Lane: 0, value: 2
CS0, Lane: 1, value: 5
CS0, Lane: 2, value: 1
CS0, Lane: 3, value: 1
DRAM: 1 GB
CS 0: base 0x00000000 size 512 MB
CS 1: base 0x20000000 size 512 MB
Addresses 38M - 0M are saved for the U-Boot usage.
SF: Detected MX25L1605D with page size 256, total 2097152 bytes
*** env_relocate_spec ****
*** Warning environment crc c6db905b c6db905b fffc.****
Warning: clock source is too slow.Try smaller resolution.
Streaming disabled
L2 Cache Prefetch disabled
L2 Cache ECC disabled
USB 0: Host Mode
USB 1: Host Mode
Setting VPU power ON.
Setting GPU power ON.
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
MMC: MV_SDHCI: 0, MV_SDHCI: 1
NORMAL MODE detected
Boot config is valid
LCD config is invalid
Using defaults
Try to load image : 0x02f00000, /tffsb
Loading file "/tffsb" from mmc device 0:2 (mmcda2)
787508 bytes read
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
MIC>>
|
Re: Chip PC LXD8941 October 14, 2018 05:38PM |
Admin Registered: 13 years ago Posts: 19,192 |
Koen,
I see. Good sense :)
I think we need to find u-boot GPL to make this more robust.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Quote
stock uboot loads an image from the 2nd partition to display on screen during boot
I see. Good sense :)
I think we need to find u-boot GPL to make this more robust.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Chip PC LXD8941 October 19, 2018 05:02PM |
Registered: 6 years ago Posts: 183 |
I've tried to setup a boot sequence where the device first tries to boot from SD, then USB and eventually the internal memory. I've used the following settings:
Unfortunately this doesn't work. Once the first attempt at booting fails the device continues into some sort of recovery mode and tries to boot from a server. I'm not sure if this is behaviour is hard coded since it is not defined in the normal uboot environment settings?
One thing I have noticed is that there is a 2nd uboot stored in mtd2 which differs from the one in mtd0. Could it be that after running uboot in mtd0 fails it tries again but runs uboot in mtd2?
It would be great if anyone has an idea how to avoid booting recovery mode and how to run a multi stage bootcmd.
Thanks,
Koen
setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 ${mtdparts} earlyprintk=serial'
setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x3000000 /boot/uImage; ext2load usb 0:1 0x4000000 /boot/uInitrd'
setenv bootcmd_sd 'mmc reset; mmcinfo 1; ext2load mmc 1:1 0x3000000 /boot/uImage; ext2load mmc 1:1 0x4000000 /boot/uInitrd'
setenv bootcmd_int 'mmc reset; mmcinfo 0; ext2load mmc 0:3 0x3000000 /boot/uImage; ext2load mmc 0:3 0x4000000 /boot/uInitrd'
setenv boot_usb 'run set_bootargs; run bootcmd_usb; bootm 0x3000000 0x4000000'
setenv boot_sd 'run set_bootargs; run bootcmd_sd; bootm 0x3000000 0x4000000'
setenv boot_int 'run set_bootargs; run bootcmd_int; bootm 0x3000000 0x4000000'
setenv bootcmd 'run boot_sd; run boot_usb; run boot_int'
saveenv
boot
Unfortunately this doesn't work. Once the first attempt at booting fails the device continues into some sort of recovery mode and tries to boot from a server. I'm not sure if this is behaviour is hard coded since it is not defined in the normal uboot environment settings?
MIC>> boot Card did not respond to voltage select! Device: MV_SDHCI Manufacturer ID: 0 OEM: 0 Name: Tran Speed: 0 Rd Block Len: 0 MMC version 0.0 High Capacity: No Capacity: 0 Bus Width: 1-bit ** Bad partition 1 ** ** Bad partition 1 ** Wrong Image Format for bootm command ERROR: can't get kernel image! Recovering... Loading file "/tffsb" from mmc device 0:2 (mmcda2) 787508 bytes read BOOTP broadcast 1 BOOTP broadcast 2 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 28 DHCP client bound to address 192.168.1.135 Using egiga0 device arp eth addr 18:62:2c:2f:bc:34 host 129.100.2.50 is alive BootMe: ClientIP=192.168.1.135, ServerIP=129.100.2.50, ServerMAC=18:62:2c:2f:bc:34 platform=8xxx, name=L BootMe: timeout 3000 msecs (1 of 3) BootMe: ClientIP=192.168.1.135, ServerIP=129.100.2.50, ServerMAC=18:62:2c:2f:bc:34 platform=8xxx, name=L BootMe: timeout 3000 msecs (2 of 3) BootMe: ClientIP=192.168.1.135, ServerIP=129.100.2.50, ServerMAC=18:62:2c:2f:bc:34 platform=8xxx, name=L BootMe: timeout 3000 msecs (3 of 3) ServerMe: broadcasting IP address=192.168.1.135, Platform=8xxx, Name=L ServerMe: timeout, 0 servers found. ServerMe: broadcasting IP address=192.168.1.135, Platform=8xxx, Name=L ServerMe: timeout, 0 servers found. ServerMe: broadcasting IP address=192.168.1.135, Platform=8xxx, Name=L Abort
One thing I have noticed is that there is a 2nd uboot stored in mtd2 which differs from the one in mtd0. Could it be that after running uboot in mtd0 fails it tries again but runs uboot in mtd2?
It would be great if anyone has an idea how to avoid booting recovery mode and how to run a multi stage bootcmd.
Thanks,
Koen
MIC>> printenv
bootdelay=0
baudrate=115200
loads_echo=0
in_mfg=no
ub_mfgphase=0000000
mb_sn=00000000
mtdids=nand0=dove-mtd
arcNumber=1789
CASset=min
MALLOC_len=5
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::dove:eth0:none
image_name=uImage
disaMvPnp=no
usb0Mode=host
usb1Mode=host
yuk_ethaddr=00:00:00:EE:51:81
autoload=no
lcd1_enable=1
ethact=egiga0
rootpath=/work/armel-dev
lcd0_enable=1
load_addr=0x2000000
bootcmd_prev=ide reset; ext2load ide 0:2 0x3000000 tffsg; setenv bootargs $(console) ip=dhcp usb0Mode=$(usb0Mode) usb1Mode=$(usb1Mode) video=dovefb:lcd0:$(lcd0_params),lcd1:$(lcd1_params) clcd.lcd0_enable=1 clcd.lcd1_enable=1; bootm 0x3000000
gatewayip=192.168.9.1
netmask=255.255.255.0
ipaddr=192.168.9.96
serverip=192.168.9.90
bootargs=console=tty0,115200 mtdparts=spi0.0:768k(u-boot),256k(uboot_env),768k(u-boot2),-(unused) rootdelay=6 cpufreq_disable pm_disable usb0Mode=host usb1Mode=host video=dovefb:lcd0:1024x768-24@60,lcd1:1024x768-24@60 clcd.lcd0_enable=1 clcd.lcd1_enable=1
bootcmd2=usb reset; ext2load usb 0:2 0x3000000 uImage; setenv bootargs $(console) mtdparts=spi0.0:768k(u-boot),256k(uboot_env),768k(u-boot2),-(unused) rootdelay=6 cpufreq_disable pm_disable usb0Mode=$(usb0Mode) usb1Mode=$(usb1Mode) video=dovefb:lcd0:$(lcd0_params),lcd1:$(lcd1_params) clcd.lcd0_enable=1 clcd.lcd1_enable=1; bootm 0x3000000
lcd0_params=1024x768-24@60-edid
lcd1_params=1024x768-24@60-edid
bootmmc=mmcinfo 0; ext2load mmc 0:2 0x3000000 tffsg; setenv bootargs $(console) mtdparts=spi0.0:768k(u-boot),256k(uboot_env),768k(u-boot2),-(unused) cpufreq_disable pm_disable usb0Mode=$(usb0Mode) usb1Mode=$(usb1Mode) video=dovefb:lcd0:$(lcd0_params),lcd1:$(lcd1_params) clcd.lcd0_enable=1 clcd.lcd1_enable=1; bootm 0x3000000
console=console=ttyS0,115200
mtdparts=mtdparts=spi0.0:768k(uboot),256k(uboot_env),768k(uboot2),-(kernel)
rootinit=root=initramfs init=/linuxrc
lcdargs=vmalloc=384MB video=dovefb:lcd0:1024x768-24@60,lcd1:1024x768-24@60 clcd.lcd0_enable=1 clcd.lcd1_enable=1
fileaddr=3000000
ethaddr=00:05:35:09:92:9A
bootcmd_exec=run set_bootargs; run bootcmd_int; bootm 0x3000000 0x4000000
usbargs=setenv bootargs ${mtdparts} console=ttyS0,115200 root=/dev/sdb1 rw rootdelay=10 video=dovefb:lcd0:1024x768-16@60,lcd1:1024x768-16@60 clcd.lcd0_enable=1 clcd.lcd1_enable=1
usbboot=usb start; sleep 3; ext2load usb 0:1 0x2000000 /boot/uImage; run usbargs;bootm 0x2000000
sataargs=root=/dev/sda1 rw init=/init video=dovefb:lcd0:1024x768-24@60,lcd1:1024x768-16@60 clcd.lcd0_enable=1 clcd.lcd1_enable=1
sataboot=ide reset;ext2load ide 0:1 0x2000000 /boot/uImage; setenv bootargs ${mtdparts} ${sataargs}; bootm 0x2000000
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 ${mtdparts} earlyprintk=serial
bootcmd_usb=usb start; ext2load usb 0:1 0x3000000 /boot/uImage; ext2load usb 0:1 0x4000000 /boot/uInitrd
bootcmd_sd=mmc reset; mmcinfo 1; ext2load mmc 1:1 0x3000000 /boot/uImage; ext2load mmc 1:1 0x4000000 /boot/uInitrd
bootcmd_int=mmc reset; mmcinfo 0; ext2load mmc 0:3 0x3000000 /boot/uImage; ext2load mmc 0:3 0x4000000 /boot/uInitrd
boot_usb=run set_bootargs; run bootcmd_usb; bootm 0x3000000 0x4000000
boot_sd=run set_bootargs; run bootcmd_sd; bootm 0x3000000 0x4000000
boot_int=run set_bootargs; run bootcmd_int; bootm 0x3000000 0x4000000
bootcmd=run boot_int
stdin=serial
stdout=lcd
stderr=lcd
passDramInitTag=yes
mainlineLinux=yes
enaMonExt=no
pexMode=RC
disL2Cache=no
disL2Ecc=no
sata_dma_mode=yes
enaL2ExtraFeatures=yes
enaCpuStream=no
enaVpuPower=yes
enaGpuPower=yes
filesize=C0434
Environment size: 3529/65532 bytes
MIC>>
|
Re: Chip PC LXD8941 October 19, 2018 09:21PM |
Admin Registered: 13 years ago Posts: 19,192 |
Koen,
The envs logic needs to be a little bit more complicate than what you currently have. I don't think I covered this part for you, since we are still getting these boxes to completelly brought up to the way we want (i.e. display, sound are remaining works).
But, since you are apprently want to use them as headless production servers now :), I will show you how to change the envs to make it resilient, and fall through the execution paths correctly from the 1st to the last device.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
The envs logic needs to be a little bit more complicate than what you currently have. I don't think I covered this part for you, since we are still getting these boxes to completelly brought up to the way we want (i.e. display, sound are remaining works).
But, since you are apprently want to use them as headless production servers now :), I will show you how to change the envs to make it resilient, and fall through the execution paths correctly from the 1st to the last device.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Chip PC LXD8941 October 19, 2018 10:14PM |
Admin Registered: 13 years ago Posts: 19,192 |
setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 ${mtdparts} earlyprintk=serial'
setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x3000000 /boot/uImage; ext2load usb 0:1 0x4000000 /boot/uInitrd'
setenv bootcmd_sd 'mmc reset; mmcinfo 1; ext2load mmc 1:1 0x3000000 /boot/uImage; ext2load mmc 1:1 0x4000000 /boot/uInitrd'
setenv bootcmd_int 'mmc reset; mmcinfo 0; ext2load mmc 0:3 0x3000000 /boot/uImage; ext2load mmc 0:3 0x4000000 /boot/uInitrd'
setenv bootcmd_bootm 'bootm 0x3000000 0x4000000'
setenv bootmcd 'run set_bootargs; if run boot_sd; then; run bootcmd_bootm; else if run boot_usb; then; run bootcmd_bootm; else if run boot_int; then; run bootcmd_bootm; fi; fi; fi'
Now, if you also want to fall back to recovery, too, then more needs to be added to bootcmd.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Chip PC LXD8941 October 20, 2018 05:28PM |
Registered: 6 years ago Posts: 183 |
Hi bodhi,
at the moment I don't care about the network booting 'recovery' option as implemented by the stock uboot.
yes I've become a bit impatient and I'm trying to get my devices in a state so that they have an easy recover option which does not require serial connection. Audio and video are nice to have but not essential in my use case. I enjoy the search for information, reverse engineering and figuring things out but seem to have reached the end of my knowledge at the moment. I did email ChipPC about the GPL sources and did get an initial response but it has been quiet ever since. Based on this I think it is unlikely that we will ever have access to uboot and/or kernel sources.
Stock uboot doesn't know 'if then else' statements so the settings you have provided don't work unfortunately.
I'm not sure if I should just adjust uboot environment such that it says 'enaMonExt=yes' instead of 'enaMonExt=no' ?
Koen
at the moment I don't care about the network booting 'recovery' option as implemented by the stock uboot.
Quote
bodhi
But, since you are apprently want to use them as headless production servers now :), I will show you how to change the envs to make it resilient, and fall through the execution paths correctly from the 1st to the last device.
yes I've become a bit impatient and I'm trying to get my devices in a state so that they have an easy recover option which does not require serial connection. Audio and video are nice to have but not essential in my use case. I enjoy the search for information, reverse engineering and figuring things out but seem to have reached the end of my knowledge at the moment. I did email ChipPC about the GPL sources and did get an initial response but it has been quiet ever since. Based on this I think it is unlikely that we will ever have access to uboot and/or kernel sources.
Quote
Chip PC
On Fri, 21 Sep 2018 at 08:42, Dan wrote:
Sorry a LXD8941 is thin client Arm , you can only boot to ThinX OS
From: Koen
Sent: Friday, September 21, 2018 2:14 AM
To: info <info@chippc.com>
Cc: info <info@chippc.com>
Subject: LXD8941 GPL and uboot sources
Hi,
I've picked up a 2nd hand LXD8941 on ebay and want to turn it into a low power home server. It would help a lot if you could point me to the uboot and GPL sources of the software used in the LXD8941.
Thanks in advance,
Koen
Stock uboot doesn't know 'if then else' statements so the settings you have provided don't work unfortunately.
MIC>> boot Unknown command 'if' - try 'help' Unknown command 'then' - try 'help' ## Booting kernel from Legacy Image at 03000000 ... Image Name: Linux-4.18.5-mvebu-tld-1 Created: 2018-10-14 16:09:11 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4465655 Bytes = 4.3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Wrong Ramdisk Image Format Ramdisk image is corrupt or invalid Unknown command 'else' - try 'help' Unknown command 'then' - try 'help' ## Booting kernel from Legacy Image at 03000000 ... Image Name: Linux-4.18.5-mvebu-tld-1 Created: 2018-10-14 16:09:11 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4465655 Bytes = 4.3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Wrong Ramdisk Image Format Ramdisk image is corrupt or invalid Unknown command 'else' - try 'help' Unknown command 'then' - try 'help' ## Booting kernel from Legacy Image at 03000000 ... Image Name: Linux-4.18.5-mvebu-tld-1 Created: 2018-10-14 16:09:11 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4465655 Bytes = 4.3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Wrong Ramdisk Image Format Ramdisk image is corrupt or invalid This command can be used only if enaMonExt is set! This command can be used only if enaMonExt is set! This command can be used only if enaMonExt is set! MIC>>
I'm not sure if I should just adjust uboot environment such that it says 'enaMonExt=yes' instead of 'enaMonExt=no' ?
Koen
|
Re: Chip PC LXD8941 October 20, 2018 06:40PM |
Admin Registered: 13 years ago Posts: 19,192 |
Koen,
> Stock uboot doesn't know 'if then else' statements
> so the settings you have provided don't work
> unfortunately.
Ah :) this u-boot is old and did not even have a hush parser activated.
> I'm not sure if I should just adjust uboot environment such that it says 'enaMonExt=yes' instead of 'enaMonExt=no' ?
I am not sure that env play any role in this.
> Audio and video are nice to have but not essential in my use case.
That's great! then you are all set to use it as a headless server. Go ahead and also try testing in Debian, I recall you've listed a summary of what capabilities we got so far for this box. Is there anything important missing?
There are still some more hacking possible in u-boot, even without the GPL source. Let me look at my notes and suggest what you can do.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Stock uboot doesn't know 'if then else' statements
> so the settings you have provided don't work
> unfortunately.
Ah :) this u-boot is old and did not even have a hush parser activated.
> I'm not sure if I should just adjust uboot environment such that it says 'enaMonExt=yes' instead of 'enaMonExt=no' ?
I am not sure that env play any role in this.
> Audio and video are nice to have but not essential in my use case.
That's great! then you are all set to use it as a headless server. Go ahead and also try testing in Debian, I recall you've listed a summary of what capabilities we got so far for this box. Is there anything important missing?
There are still some more hacking possible in u-boot, even without the GPL source. Let me look at my notes and suggest what you can do.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Chip PC LXD8941 October 21, 2018 10:43AM |
Registered: 6 years ago Posts: 183 |
Hi bodhi,
I've found a way to get multi stage booting to work without 'if then' statements or dropping into the stock network boot recovery mode. My settings are listed below. First it loads the uImage and uInitrd from internal memory into RAM. Then it tries to load them from the SD card. If an SD card is present the uImage and uInitrd in RAM get overwritten by those from the SD card, resulting in the device booting from the SD card. If no SD card is present the uImage and uInitrd in RAM remain unchanged and the device boots from internal memory.
This probably isn't the cleanest solution since if there is a difference in the 2 uImage and uInitrd file sizes you could end up with bits of RAM that contain executable code which does not get overwritten. However I think this risk is small and it does allow me to run the device with an easy recovery method.
Koen
Edit:
Ok some more testing shows that this setup is not completely reliable. The uImage and uInitrd get loaded OK but when there are 2 rootfs available it is a bit random which one gets used.
Edited 1 time(s). Last edit at 10/21/2018 11:30AM by Koen.
I've found a way to get multi stage booting to work without 'if then' statements or dropping into the stock network boot recovery mode. My settings are listed below. First it loads the uImage and uInitrd from internal memory into RAM. Then it tries to load them from the SD card. If an SD card is present the uImage and uInitrd in RAM get overwritten by those from the SD card, resulting in the device booting from the SD card. If no SD card is present the uImage and uInitrd in RAM remain unchanged and the device boots from internal memory.
This probably isn't the cleanest solution since if there is a difference in the 2 uImage and uInitrd file sizes you could end up with bits of RAM that contain executable code which does not get overwritten. However I think this risk is small and it does allow me to run the device with an easy recovery method.
Koen
setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 ${mtdparts} earlyprintk=serial'
setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x3000000 /boot/uImage; ext2load usb 0:1 0x4000000 /boot/uInitrd'
setenv bootcmd_sd 'mmc reset; mmcinfo 1; ext2load mmc 1:1 0x3000000 /boot/uImage; ext2load mmc 1:1 0x4000000 /boot/uInitrd'
setenv bootcmd_int 'mmc reset; mmcinfo 0; ext2load mmc 0:3 0x3000000 /boot/uImage; ext2load mmc 0:3 0x4000000 /boot/uInitrd'
setenv bootcmd_bootm 'bootm 0x3000000 0x4000000'
setenv bootcmd 'run set_bootargs; run bootcmd_int; run bootcmd_sd; run bootcmd_bootm'
saveenv
boot
Edit:
Ok some more testing shows that this setup is not completely reliable. The uImage and uInitrd get loaded OK but when there are 2 rootfs available it is a bit random which one gets used.
Edited 1 time(s). Last edit at 10/21/2018 11:30AM by Koen.
|
Re: Chip PC LXD8941 October 21, 2018 12:07PM |
Registered: 6 years ago Posts: 183 |
Ok I think the solution may be to create an uboot script as described on the website:
https://www.denx.de/wiki/DULG/UBootScripts
The script would contain a single line which changes the label to a different name for the SD card.
The script would be sourced from the SD card so the label is only changed when the SD card is actually present. If the SD card is not present the script can't be sourced and hopefully the device will continue to boot from the internal memory.
Koen
Edited 1 time(s). Last edit at 10/21/2018 01:28PM by Koen.
https://www.denx.de/wiki/DULG/UBootScripts
The script would contain a single line which changes the label to a different name for the SD card.
setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfsSD rootdelay=10 ${mtdparts} earlyprintk=serial'
The script would be sourced from the SD card so the label is only changed when the SD card is actually present. If the SD card is not present the script can't be sourced and hopefully the device will continue to boot from the internal memory.
Koen
Edited 1 time(s). Last edit at 10/21/2018 01:28PM by Koen.
|
Re: Chip PC LXD8941 October 21, 2018 02:18PM |
Registered: 6 years ago Posts: 183 |
The following method works to make the device boot from SD card when present or otherwise from the internal memory:
Create a file changeLabelSD.txt which contains the following line. This script adjusts the root file system label which is passed to the kernel to avoid confusion.
Execute the following command to convert this script into an .img file that can be parsed by uboot.
Copy changeLabelSD.img to the root of your SD card. Change the label of the SD card to rootfsSD so it matches the setting in the script.
Adjust the uboot environment as follows:
The load address 0x10000000 is just a large number so it is hopefully far enough away from uImage and uInitrd. It seems to work OK since the device boots from the SD card if it can find it during boot and otherwise it boots from the internal memory.
Koen
Edited 1 time(s). Last edit at 10/21/2018 02:21PM by Koen.
Create a file changeLabelSD.txt which contains the following line. This script adjusts the root file system label which is passed to the kernel to avoid confusion.
setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfsSD rootdelay=10 ${mtdparts} earlyprintk=serial'
Execute the following command to convert this script into an .img file that can be parsed by uboot.
mkimage -T script -C none -n 'change label SD' -d changeLabelSD.txt changeLabelSD.img
Copy changeLabelSD.img to the root of your SD card. Change the label of the SD card to rootfsSD so it matches the setting in the script.
Adjust the uboot environment as follows:
setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 ${mtdparts} earlyprintk=serial'
setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x3000000 /boot/uImage; ext2load usb 0:1 0x4000000 /boot/uInitrd'
setenv bootcmd_sd 'mmc reset; mmcinfo 1; ext2load mmc 1:1 0x3000000 /boot/uImage; ext2load mmc 1:1 0x4000000 /boot/uInitrd'
setenv bootcmd_int 'mmc reset; mmcinfo 0; ext2load mmc 0:3 0x3000000 /boot/uImage; ext2load mmc 0:3 0x4000000 /boot/uInitrd'
setenv bootcmd_bootm 'bootm 0x3000000 0x4000000'
setenv changelabel 'mmc reset; mmcinfo 1; ext2load mmc 1:1 0x10000000 /changeLabelSD.img; source 0x10000000'
setenv bootcmd 'run set_bootargs; run bootcmd_int; run changelabel; run bootcmd_sd; run bootcmd_bootm'
saveenv
boot
The load address 0x10000000 is just a large number so it is hopefully far enough away from uImage and uInitrd. It seems to work OK since the device boots from the SD card if it can find it during boot and otherwise it boots from the internal memory.
Koen
Edited 1 time(s). Last edit at 10/21/2018 02:21PM by Koen.
|
Re: Chip PC LXD8941 October 21, 2018 02:46PM |
Registered: 6 years ago Posts: 183 |
The script does work but is not completely correct since dmesg shows the following:
resulting in this:
It seems that ${mtdparts} does not get replaced by the value / string that is already present in the uboot environment settings. Maybe scripts don't have access to the other environment values. Anyway I guess I need to add a line which defines mtdparts to the script and try again.
Koen
0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfsSD rootdelay=10 ${mtdparts} earlyprintk=serial
resulting in this:
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00200000 00001000 "spi0.0" root@debian:~#
It seems that ${mtdparts} does not get replaced by the value / string that is already present in the uboot environment settings. Maybe scripts don't have access to the other environment values. Anyway I guess I need to add a line which defines mtdparts to the script and try again.
Koen
|
Re: Chip PC LXD8941 October 21, 2018 03:07PM |
Registered: 6 years ago Posts: 183 |
Either I'm making a mistake somewhere or this version of uboot doesn't seem to like parameter substitution in scripts. Using the following complete line in the script does work:
as shown by dmesg:
Koen
setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfsSD rootdelay=10 mtdparts=spi0.0:768k(uboot),256k(uboot_env),768k(uboot2),-(kernel) earlyprintk=serial'
as shown by dmesg:
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfsSD rootdelay=10 mtdparts=spi0.0:768k(uboot),256k(uboot_env),768k(uboot2),-(kernel) earlyprintk=serial
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 000c0000 00001000 "uboot" mtd1: 00040000 00001000 "uboot_env" mtd2: 000c0000 00001000 "uboot2" mtd3: 00040000 00001000 "kernel"
Koen
|
Re: Chip PC LXD8941 October 21, 2018 04:17PM |
Admin Registered: 13 years ago Posts: 19,192 |
Koen,
No need to use the boot script (more moving parts), you should just set a different root label in the bootargs for each type of device. You can also use an env for this rootfs label, too. Something like this.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 10/21/2018 04:18PM by bodhi.
No need to use the boot script (more moving parts), you should just set a different root label in the bootargs for each type of device. You can also use an env for this rootfs label, too. Something like this.
setenv set_bootargs_int 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfsINT rootdelay=10 ${mtdparts} earlyprintk=serial'
setenv set_bootargs_sd 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfsSD rootdelay=10 ${mtdparts} earlyprintk=serial'
setenv set_bootargs_usb 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfsUSB rootdelay=10 ${mtdparts} earlyprintk=serial'
setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x3000000 /boot/uImage; ext2load usb 0:1 0x4000000 /boot/uInitrd'
setenv bootcmd_sd 'mmc reset; mmcinfo 1; ext2load mmc 1:1 0x3000000 /boot/uImage; ext2load mmc 1:1 0x4000000 /boot/uInitrd'
setenv bootcmd_int 'mmc reset; mmcinfo 0; ext2load mmc 0:3 0x3000000 /boot/uImage; ext2load mmc 0:3 0x4000000 /boot/uInitrd'
setenv bootcmd_bootm 'bootm 0x3000000 0x4000000'
setenv bootcmd 'run set_bootargs_int; run bootcmd_int; run set_bootargs_sd; run bootcmd_sd; run bootcmd_bootm'
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 10/21/2018 04:18PM by bodhi.
