Re: Chip PC LXD8941 October 21, 2018 04:46PM |
Registered: 6 years ago Posts: 183 |
Re: Chip PC LXD8941 October 21, 2018 05:08PM |
Admin Registered: 13 years ago Posts: 18,898 |
Re: Chip PC LXD8941 October 22, 2018 04:44PM |
Registered: 6 years ago Posts: 183 |
Re: Chip PC LXD8941 October 22, 2018 06:01PM |
Admin Registered: 13 years ago Posts: 18,898 |
setenv bootcmd 'run set_bootargs_int; run bootcmd_int; run set_bootargs_sd; run bootcmd_sd; run bootcmd_bootm'
run set_bootargs_int; # set to internal therefore root=LABEL=rootfsINT run bootcmd_int; # when this fail it should proceed to run set_bootargs_sd run set_bootargs_sd; # reset to SD therefore root=LABEL=rootfsSD run bootcmd_sd; # when this fail it should proceed to run bootcmd_bootm which will fail run bootcmd_bootm # as this fails, the bahavior is depending on the box u-boot, it could reset, or hung.You need to test this.
Re: Chip PC LXD8941 October 23, 2018 04:13PM |
Registered: 6 years ago Posts: 183 |
setenv bootcmd 'run set_bootargs_int; run bootcmd_int; run set_bootargs_sd; run bootcmd_sd; run bootcmd_bootm'
setenv bootcmd 'run set_bootargs_sd; run bootcmd_sd; run set_bootargs_int; run bootcmd_int; run bootcmd_bootm'
Re: Chip PC LXD8941 October 23, 2018 05:39PM |
Admin Registered: 13 years ago Posts: 18,898 |
Quote
If I run the following bootcmd the bootargs are always set to root=LABEL=rootfsSD so the device will boot OK from SD but will fail to boot the rescue system on the internal memory when no SD card is present.
setenv bootcmd 'run set_bootargs_int; run bootcmd_int; run set_bootargs_sd; run bootcmd_sd; run bootcmd_bootm'
setenv bootcmd 'run set_bootargs_sd; run bootcmd_sd; run bootcmd_bootm; run set_bootargs_int; run bootcmd_int; run bootcmd_bootm;'
Re: Chip PC LXD8941 October 24, 2018 01:34PM |
Registered: 6 years ago Posts: 183 |
Hit any key to stop autoboot: 0 Card did not respond to voltage select! Device: MV_SDHCI Manufacturer ID: 0 OEM: 0 Name: Tran Speed: 0 Rd Block Len: 0 MMC version 0.0 High Capacity: No Capacity: 0 Bus Width: 1-bit ** Bad partition 1 ** ** Bad partition 1 ** Wrong Image Format for bootm command ERROR: can't get kernel image! Recovering... Loading file "/tffsb" from mmc device 0:2 (mmcda2) 787508 bytes read BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 28 DHCP client bound to address 192.168.1.135 Using egiga0 device arp eth addr 18:62:2c:2f:bc:34 host 129.100.2.50 is alive BootMe: ClientIP=192.168.1.135, ServerIP=129.100.2.50, ServerMAC=18:62:2c:2f:bc:34 platform=8xxx, name=L BootMe: timeout 3000 msecs (1 of 3) BootMe: ClientIP=192.168.1.135, ServerIP=129.100.2.50, ServerMAC=18:62:2c:2f:bc:34 platform=8xxx, name=L BootMe: timeout 3000 msecs (2 of 3) BootMe: ClientIP=192.168.1.135, ServerIP=129.100.2.50, ServerMAC=18:62:2c:2f:bc:34 platform=8xxx, name=L BootMe: timeout 3000 msecs (3 of 3) ServerMe: broadcasting IP address=192.168.1.135, Platform=8xxx, Name=L ServerMe: timeout, 0 servers found. ServerMe: broadcasting IP address=192.168.1.135, Platform=8xxx, Name=L ServerMe: timeout, 0 servers found. ServerMe: broadcasting IP address=192.168.1.135, Platform=8xxx, Name=L ServerMe: timeout, 0 servers found. ServerMe: broadcasting IP address=192.168.1.135, Platform=8xxx, Name=L
Re: Chip PC LXD8941 October 24, 2018 02:32PM |
Admin Registered: 13 years ago Posts: 18,898 |
Re: Chip PC LXD8941 --> LXD8541 October 27, 2018 03:28AM |
Registered: 9 years ago Posts: 295 |
Re: Chip PC LXD8941 October 27, 2018 06:25AM |
Registered: 6 years ago Posts: 183 |
Re: Chip PC LXD8941 October 27, 2018 04:37PM |
Registered: 9 years ago Posts: 295 |
| | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2009.08-svn7881 (Jan 23 2013 - 13:55:26) version: dove-5.3.4 BootROM: Version on chip: 2.33 Status: OK Retries #: 0 Board: RD-88AP510-Avengers SoC: MV88F510 Rev 7 CPU: ??? (0x0c08) (Rev 1) CPU @ 800Mhz, L2 @ 400Mhz DDR3 @ 400Mhz, TClock @ 166Mhz PEX 0: interface detected no Link. PEX 1: interface detected no Link. Write Leveling Results: CS0, Lane: 0, value: 2 CS0, Lane: 1, value: 3 CS0, Lane: 2, value: 1 CS0, Lane: 3, value: 1 DRAM: 1 GB CS 0: base 0x00000000 size 512 MB CS 1: base 0x20000000 size 512 MB Addresses 38M - 0M are saved for the U-Boot usage. SF: Detected MX25L1605D with page size 256, total 2097152 bytes *** env_relocate_spec **** *** Warning environment crc cae2a0b3 cae2a0b3 fffc.**** Warning: clock source is too slow.Try smaller resolution. Streaming disabled L2 Cache Prefetch disabled L2 Cache ECC disabled USB 0: Host Mode USB 1: Host Mode Setting VPU power ON. Setting GPU power ON. PEX 0: interface detected no Link. PEX 1: interface detected no Link. MMC: MV_SDHCI: 0, MV_SDHCI: 1 NORMAL MODE detected Boot config is valid LCD config is invalid Using defaults Try to load image : 0x02f00000, /tffsb Loading file "/tffsb" from mmc device 0:2 (mmcda2) 787508 bytes read Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 MIC>> MIC>> MIC>> MIC>> MIC>> MIC>> MIC>> MIC>> setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 ${mtdparts} earlyprintk=serial' MIC>> setenv bootcmd_usb 'usb start; fatload usb 0:1 0x3000000 /uImage; fatload usb 0:1 0x4000000 /uInitrd' MIC>> setenv bootcmd_exec 'run set_bootargs; run bootcmd_usb; bootm 0x3000000 0x4000000' MIC>> sa Saving Environment to SPI Flash... Erasing 0xc0000 - 0xd0000: [Done] Writing to SPI flash: [Done] MIC>> run bootcmd_exec (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found Waiting for storage device(s) to settle before scanning... scanning bus for storage devices... 1 Storage Device(s) found reading /uImage ............................................................................................................................................................................................ ....................................................................................................................................................................................... 4465752 bytes read reading /uInitrd ............................................................................................................................................................................................ 7931992 bytes read ## Booting kernel from Legacy Image at 03000000 ... Image Name: Linux-4.18.4 Created: 2018-10-27 20:20:00 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4465688 Bytes = 4.3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 04000000 ... Image Name: initramfs-4.18.4 Created: 2018-10-27 20:20:55 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7931928 Bytes = 7.6 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... EUGENE lcd_disable EUGENE lcd_panel_disable Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.18.5-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9)) #1 SMP PREEMPT Thu Aug 30 22:19:21 PDT 2018 [ 0.000000] CPU: ARMv7 Processor [413fc081] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Chip PC LXD8941 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] random: get_random_bytes called from start_kernel+0x78/0x4c4 with crng_init=0 [ 0.000000] percpu: Embedded 18 pages/cpu @(ptrval) s41548 r8192 d23988 u73728 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi0.0:768k(uboot),256k(uboot_env),768k(uboot2),-(kernel) earlyprintk=serial [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1017252K/1048576K available (9216K kernel code, 790K rwdata, 2304K rodata, 1024K init, 327K bss, 31324K reserved, 0K cma-reserved, 262144K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (10208 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 791 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 328 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] Division by zero in kernel. [ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.18.5-mvebu-tld-1 #1 [ 0.000000] Hardware name: Marvell Dove [ 0.000000] [<c0117d00>] (unwind_backtrace) from [<c0112680>] (show_stack+0x10/0x14) [ 0.000000] [<c0112680>] (show_stack) from [<c0944f18>] (dump_stack+0x70/0x8c) [ 0.000000] [<c0944f18>] (dump_stack) from [<c0943574>] (Ldiv0+0x8/0x10) [ 0.000000] [<c0943574>] (Ldiv0) from [<c05c2fbc>] (dove_recalc_rate+0x44/0x8c) [ 0.000000] [<c05c2fbc>] (dove_recalc_rate) from [<c05bed1c>] (clk_register+0x40c/0x5d4) [ 0.000000] [<c05bed1c>] (clk_register) from [<c0d35580>] (dove_divider_clk_init+0x12c/0x190) [ 0.000000] [<c0d35580>] (dove_divider_clk_init) from [<c0d353c8>] (dove_clk_init+0x4c/0x74) [ 0.000000] [<c0d353c8>] (dove_clk_init) from [<c0d3353c>] (of_clk_init+0x184/0x240) [ 0.000000] [<c0d3353c>] (of_clk_init) from [<c0d04004>] (time_init+0x20/0x2c) [ 0.000000] [<c0d04004>] (time_init) from [<c0d00d14>] (start_kernel+0x2f8/0x4c4) [ 0.000000] [<c0d00d14>] (start_kernel) from [<00000000>] ( (null)) [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000008] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.007836] Switching to timer-based delay loop, resolution 6ns [ 0.014595] Console: colour dummy device 80x30 [ 0.019110] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.029632] pid_max: default: 32768 minimum: 301 [ 0.034511] Security Framework initialized [ 0.038765] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.045371] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.053568] CPU: Testing write buffer coherency: ok [ 0.058518] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.068362] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.128015] Setting up static identity map for 0x100000 - 0x100060 [ 0.135077] Hierarchical SRCU implementation. [ 0.177903] smp: Bringing up secondary CPUs ... [ 0.182423] smp: Brought up 1 node, 1 CPU [ 0.186413] SMP: Total of 1 processors activated (333.33 BogoMIPS). [ 0.192718] CPU: All CPU(s) started in SVC mode. [ 0.198489] devtmpfs: initialized [ 0.208175] VFP support v0.3: implementor 41 architecture 2 part 20 variant 9 rev 5 [ 0.216721] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.226973] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.233536] prandom: seed boundary self test passed [ 0.242278] prandom: 100 self tests passed [ 0.246358] pinctrl core: initialized pinctrl subsystem [ 0.254586] NET: Registered protocol family 16 [ 0.261147] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.268767] audit: initializing netlink subsys (disabled) [ 0.276981] audit: type=2000 audit(0.260:1): state=initialized audit_enabled=0 res=1 [ 0.298231] cpuidle: using governor ladder [ 0.302463] cpuidle: using governor menu [ 0.306634] Dove 88AP510 SoC [ 0.309650] Tauros2: Disabling L2 prefetch. [ 0.313816] Tauros2: Disabling burst8 line fill. [ 0.318544] Tauros2: Enabling L2 cache. [ 0.322371] Tauros2: L2 cache support initialised in ARMv7 mode. [ 0.328840] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.439001] vgaarb: loaded [ 0.442086] SCSI subsystem initialized [ 0.448452] usbcore: registered new interface driver usbfs [ 0.453970] usbcore: registered new interface driver hub [ 0.460612] usbcore: registered new device driver usb [ 0.466522] media: Linux media interface: v0.10 [ 0.471723] videodev: Linux video capture interface: v2.00 [ 0.477807] pps_core: LinuxPPS API ver. 1 registered [ 0.483237] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.492591] PTP clock support registered [ 0.499320] clocksource: Switched to clocksource orion_clocksource [ 0.606619] VFS: Disk quotas dquot_6.6.0 [ 0.610660] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.641602] NET: Registered protocol family 2 [ 0.647216] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.655633] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.663044] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.669615] TCP: Hash tables configured (established 8192 bind 8192) [ 0.676059] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.682062] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.688674] NET: Registered protocol family 1 [ 0.723856] RPC: Registered named UNIX socket transport module. [ 0.729841] RPC: Registered udp transport module. [ 0.734523] RPC: Registered tcp transport module. [ 0.739206] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.745919] Unpacking initramfs... [ 1.351766] Freeing initrd memory: 7748K [ 1.355917] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.365621] Initialise system trusted keyrings [ 1.371326] Key type blacklist registered [ 1.375525] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 1.382173] zbud: loaded [ 1.395917] NFS: Registering the id_resolver key type [ 1.401189] Key type id_resolver registered [ 1.405350] Key type id_legacy registered [ 1.409427] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.416100] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.422809] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.430513] orangefs_debugfs_init: called with debug mask: :none: :0: [ 1.437138] orangefs_init: module version upstream loaded [ 1.450298] Key type asymmetric registered [ 1.454384] Asymmetric key parser 'x509' registered [ 1.459436] bounce: pool size: 64 pages [ 1.463429] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 1.471173] io scheduler noop registered [ 1.475076] io scheduler deadline registered [ 1.479481] io scheduler cfq registered (default) [ 1.486750] dove-pinctrl f10d0200.pin-ctrl: falling back to hardcoded PMU resource [ 1.495526] dove-pinctrl f10d0200.pin-ctrl: [Firmware Bug]: Missing pinctrl regs in DTB. Please update your firmware. [ 1.506989] dove-pinctrl f10d0200.pin-ctrl: registered pinctrl driver [ 1.520644] mvebu-pcie mbus:pcie: PCI host bridge to bus 0000:00 [ 1.526639] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.533073] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 1.540148] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.547883] PCI: bus0: Fast back to back transfers disabled [ 1.553708] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.561810] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.571471] PCI: bus1: Fast back to back transfers enabled [ 1.578661] PCI: bus2: Fast back to back transfers enabled [ 1.584258] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.589215] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.595542] mv_xor f1060800.dma-engine: Marvell shared XOR driver [ 1.660611] mv_xor f1060800.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.668969] mv_xor f1060900.dma-engine: Marvell shared XOR driver [ 1.730604] mv_xor f1060900.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.893696] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.904415] console [ttyS0] disabled [ 1.908868] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 21, base_baud = 10416666) is a 16550A [ 1.918129] console [ttyS0] enabled [ 1.918129] console [ttyS0] enabled [ 1.925364] bootconsole [earlycon0] disabled [ 1.925364] bootconsole [earlycon0] disabled [ 1.935309] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 22, base_baud = 10416666) is a 16550A [ 1.946848] sata_mv f10a0000.sata-host: slots 32 ports 1 [ 1.964892] scsi host0: sata_mv [ 1.968666] ata1: SATA max UDMA/133 irq 33 [ 1.975285] m25p80 spi0.0: found mx25l1606e, expected sst25vf080b [ 1.981545] m25p80 spi0.0: mx25l1606e (2048 Kbytes) [ 1.987028] 4 cmdlinepart partitions found on MTD device spi0.0 [ 1.993897] Creating 4 MTD partitions on "spi0.0": [ 1.998677] 0x000000000000-0x0000000c0000 : "uboot" [ 2.005288] 0x0000000c0000-0x000000100000 : "uboot_env" [ 2.012414] 0x000000100000-0x0000001c0000 : "uboot2" [ 2.019191] 0x0000001c0000-0x000000200000 : "kernel" [ 2.029631] libphy: Fixed MDIO Bus: probed [ 2.037825] libphy: orion_mdio_bus: probed [ 2.051213] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.150798] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:05:35:06:33:d4 [ 2.160851] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.167373] ehci-pci: EHCI PCI platform driver [ 2.172479] ehci-orion: EHCI orion driver [ 2.176672] orion-ehci f1050000.usb-host: EHCI Host Controller [ 2.182683] orion-ehci f1050000.usb-host: new USB bus registered, assigned bus number 1 [ 2.191125] orion-ehci f1050000.usb-host: irq 26, io mem 0xf1050000 [ 2.219360] orion-ehci f1050000.usb-host: USB 2.0 started, EHCI 1.00 [ 2.226029] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18 [ 2.234318] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.241557] usb usb1: Product: EHCI Host Controller [ 2.246416] usb usb1: Manufacturer: Linux 4.18.5-mvebu-tld-1 ehci_hcd [ 2.252876] usb usb1: SerialNumber: f1050000.usb-host [ 2.258799] hub 1-0:1.0: USB hub found [ 2.262824] hub 1-0:1.0: 1 port detected [ 2.267650] orion-ehci f1051000.usb-host: EHCI Host Controller [ 2.273818] orion-ehci f1051000.usb-host: new USB bus registered, assigned bus number 2 [ 2.282058] orion-ehci f1051000.usb-host: irq 27, io mem 0xf1051000 [ 2.298472] random: fast init done [ 2.301927] ata1: SATA link down (SStatus 0 SControl F300) [ 2.309369] orion-ehci f1051000.usb-host: USB 2.0 started, EHCI 1.00 [ 2.315994] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18 [ 2.324291] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.331511] usb usb2: Product: EHCI Host Controller [ 2.336367] usb usb2: Manufacturer: Linux 4.18.5-mvebu-tld-1 ehci_hcd [ 2.342801] usb usb2: SerialNumber: f1051000.usb-host [ 2.348641] hub 2-0:1.0: USB hub found [ 2.352648] hub 2-0:1.0: 1 port detected [ 2.358234] usbcore: registered new interface driver usblp [ 2.364522] usbcore: registered new interface driver usb-storage [ 2.371297] mousedev: PS/2 mouse device common for all mice [ 2.378467] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time-clock as rtc0 [ 2.388495] i2c /dev entries driver [ 2.395625] orion_wdt: Initial timeout 25 sec [ 2.404935] marvell-cesa f1030000.crypto-engine: CESA device successfully registered [ 2.413506] hidraw: raw HID events driver (C) Jiri Kosina [ 2.420207] usbcore: registered new interface driver usbhid [ 2.425752] usbhid: USB HID core driver [ 2.430792] drop_monitor: Initializing network drop monitor service [ 2.437561] NET: Registered protocol family 10 [ 2.453702] Segment Routing with IPv6 [ 2.457450] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.465833] NET: Registered protocol family 17 [ 2.470884] 8021q: 802.1Q VLAN Support v1.8 [ 2.475099] Key type dns_resolver registered [ 2.479826] ThumbEE CPU extension supported. [ 2.484091] Registering SWP/SWPB emulation handler [ 2.490011] registered taskstats version 1 [ 2.494095] Loading compiled-in X.509 certificates [ 2.498938] zswap: loaded using pool lzo/zbud [ 2.523012] Key type big_key registered [ 2.535945] Key type encrypted registered [ 2.543553] rtc-mv f10d8500.real-time-clock: setting system clock to 2025-12-13 03:34:14 UTC (1765596854) [ 2.556701] Freeing unused kernel memory: 1024K [ 2.563842] Checked W+X mappings: passed, no W+X pages found Loading, please wait... [ 2.629449] usb 1-1: new high-speed USB device number 2 using orion-ehci starting version 232 [ 2.692524] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.708991] random: udevadm: uninitialized urandom read (16 bytes read) [ 2.716426] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.723649] usb 2-1: new high-speed USB device number 2 using orion-ehci [ 2.851251] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98 [ 2.869412] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 2.876523] usb 1-1: Product: USB2.0 Hub [ 2.899131] hub 1-1:1.0: USB hub found [ 2.909895] hub 1-1:1.0: 4 ports detected [ 2.951303] usb 2-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98 [ 2.969455] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 2.976567] usb 2-1: Product: USB2.0 Hub [ 2.998453] hub 2-1:1.0: USB hub found [ 3.010612] hub 2-1:1.0: 4 ports detected [ 3.359596] i2c i2c-0: Added multiplexed i2c bus 1 [ 3.379765] i2c i2c-0: Added multiplexed i2c bus 2 [ 3.411267] i2c i2c-0: Added multiplexed i2c bus 3 [ 3.419417] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 3.531108] sdhci: Secure Digital Host Controller Interface driver [ 3.537298] sdhci: Copyright(c) Pierre Ossman [ 3.577317] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.584996] usb 1-1.1: New USB device found, idVendor=8564, idProduct=1000, bcdDevice=11.00 [ 3.599383] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.606702] usb 1-1.1: Product: Mass Storage Device [ 3.619770] mmc0 bounce up to 128 segments into one, max segment size 65536 bytes [ 3.627400] usb 1-1.1: Manufacturer: JetFlash [ 3.634341] usb 1-1.1: SerialNumber: 17FFN7GE2ZIDHTYT [ 3.645744] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 3.673845] scsi host1: usb-storage 1-1.1:1.0 [ 3.682040] mmc0: SDHCI controller on f1090000.sdio-host [f1090000.sdio-host] using DMA [ 3.706392] sdhci-dove f1092000.sdio-host: Got CD GPIO [ 3.725060] mmc1 bounce up to 128 segments into one, max segment size 65536 bytes [ 3.785749] mmc1: SDHCI controller on f1092000.sdio-host [f1092000.sdio-host] using DMA [ 4.964686] usbcore: registered new interface driver uas Begin: Loading essential drivers ... done. [ 5.044499] scsi 1:0:0:0: Direct-Access JetFlash Transcend 16GB 1100 PQ: 0 ANSI: 4 [ 5.059681] sd 1:0:0:0: [sda] 30818304 512-byte logical blocks: (15.8 GB/14.7 GiB) [ 5.074099] sd 1:0:0:0: [sda] Write Protect is off [ 5.084278] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.109413] sda: sda1 sda2 sda3 [ 5.120541] sd 1:0:0:0: [sda] Attached SCSI removable disk Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.29.2 [/sbin/fsck.ext4 (1) -- /dev/sda3] fsck.ext4 -a -C0 /dev/sda3 rootfs: clean, 142178/930240 files, 1245377/3720960 blocks done. [ 15.275233] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Setting hostname to 'debian'...done. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [....] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 18.219600] sd 1:0:0:0: Attached scsi generic sg0 type 0 done. [....] Activating swap:swapon: /dev/sda2: found signature [page[ 21.020455] Adding 262140k swap on /dev/sda2. Priority:-2 extents:1 across:262140k FS size=4096, signature=swap] swapon: /dev/sda2: pagesize=4096, swapsize=268435456, devsize=268435456 swapon /dev/sda2 . ok [ 21.189580] EXT4-fs (sda3): re-mounted. Opts: (null) [....] Will now activate lvm and md swap:[ 22.019449] random: crng init done [ 22.022978] random: 7 urandom warning(s) missed due to ratelimiting swapon: /dev/sda2: already active -- ignored done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. /dev/disk/by-label/rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. ok [....] Cleaning up temporary files...[....] Cleaning /tmp...done. /tmp. ok [....] Will now mount local filesystems:. ok [....] Will now activate swapfile swap:swapon: /dev/sda2: already active -- ignored done. [....] Checking minimum space in /tmp...done. [....] Cleaning up temporary files.... ok [....] Setting kernel variables...done. [....] Initializing random number generator...done. [ 24.365025] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 24.400148] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 24.408217] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 24.417003] cfg80211: failed to load regulatory.db [ 24.770426] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...eth0: waiting for carrier [ 27.764020] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 27.773878] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready eth0: carrier acquired eth0: adding address fe80::9021:ca8:dc86:fc65 DUID 00:01:00:01:23:66:d2:86:aa:6f:7b:d1:ea:4e eth0: IAID 35:06:33:d4 eth0: soliciting a DHCP lease eth0: soliciting an IPv6 router eth0: offered 192.168.178.115 from 192.168.178.1 eth0: probing address 192.168.178.115/24 eth0: Router Advertisement from fe80::ca0e:14ff:fec3:ea8c eth0: adding address 2a01:c22:3422:1900:e03:f169:17e6:3e97/64 eth0: adding route to 2a01:c22:3422:1900::/64 eth0: adding default route via fe80::ca0e:14ff:fec3:ea8c eth0: no useable IA found in lease eth0: dhcp6_readlease: /var/lib/dhcpcd5/dhcpcd-eth0.lease6: No such process eth0: soliciting a DHCPv6 lease eth0: REPLY6 received from fe80::ca0e:14ff:fec3:ea8c eth0: adding address 2a01:c22:3422:1900:9021:ca8:dc86:fc65/128 eth0: renew in 1800 seconds, rebind in 2880 seconds forked to background, child pid 2354 done. [....] Starting RPC port mapper daemon: rpcbind. ok [....] Starting NFS common utilities: statd idmapd. ok [....] Cleaning up temporary files.... ok [....] Setting sensors limits...No sensors found! Make sure you loaded all the kernel drivers you need. Try sensors-detect to find out which these are. No sensors found! Make sure you loaded all the kernel drivers you need. Try sensors-detect to find out which these are. done. INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Not starting NFS kernel daemon: no exports. ... (warning). [....] Not running dhcpcd because there is aleady an interface specific instance ... failed! [....] /var/run/dhcpcd-eth0.pid ... failed! [....] Starting system logging: syslog-ng. ok [....] Starting periodic command scheduler: cron. ok [....] Starting system message bus: dbus. ok [....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. ok [....] Starting NTP server: ntpd. ok [....] Not starting S.M.A.R.T. daemon smartd, disabled via /etc/default/smartmontools ... (warning). [....] Starting OpenBSD Secure Shell server: sshd. ok [....] Running local boot scripts (/etc/rc.local). ok [....] startpar: service(s) skipped, program is not configured: dhcpcd ... (warning). Debian GNU/Linux 9 debian ttyS0
Re: Chip PC LXD8941 October 27, 2018 04:58PM |
Admin Registered: 13 years ago Posts: 18,898 |
Re: Chip PC LXD8941 October 27, 2018 05:32PM |
Registered: 9 years ago Posts: 295 |
MIC>> printenv bootdelay=0 baudrate=115200 loads_echo=0 in_mfg=no ub_mfgphase=0000000 mb_sn=00000000 mtdids=nand0=dove-mtd arcNumber=1789 CASset=min MALLOC_len=5 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::dove:eth0:none image_name=uImage sataargs=root=/dev/sda1 rw init=/init video=dovefb:lcd0:1024x768-24@60,lcd1:1024x768-16@60 clcd.lcd0_enable=1 clcd.lcd1_enable=1 sataboot=ide reset;ext2load ide 0:1 0x2000000 /boot/uImage; setenv bootargs ${mtdparts} ${sataargs}; bootm 0x2000000 usbboot=usb start; sleep 3; ext2load usb 0:1 0x2000000 /boot/uImage; run usbargs;bootm 0x2000000 disaMvPnp=no usb0Mode=host usb1Mode=host yuk_ethaddr=00:00:00:EE:51:81 autoload=no lcd1_enable=1 ethact=egiga0 rootpath=/work/armel-dev lcd0_enable=1 nfsboot=tftpboot 0x2000000 uImage521g; setenv bootargs $(console) $(bootargs_root) nfsroot=$(serverip):$(rootpath) ip=dhcp usb0Mode=$(usb0Mode) usb1Mode=$(usb1Mode) video=dovefb:lcd0:$(lc0 load_addr=0x2000000 bootcmd_prev=ide reset; ext2load ide 0:2 0x3000000 tffsg; setenv bootargs $(console) ip=dhcp usb0Mode=$(usb0Mode) usb1Mode=$(usb1Mode) video=dovefb:lcd0:$(lcd0_params),lcd1:$(lcd1_params)0 gatewayip=192.168.9.1 netmask=255.255.255.0 ipaddr=192.168.9.96 serverip=192.168.9.90 bootargs=console=tty0,115200 mtdparts=spi0.0:768k(u-boot),256k(uboot_env),768k(u-boot2),-(unused) rootdelay=6 cpufreq_disable pm_disable usb0Mode=host usb1Mode=host video=dovefb:lcd0:10241 boottest=ide reset; ext2load ide 0:2 0x3000000 uImage; setenv bootargs $(console) $(mtdparts) ip=dhcp usb0Mode=$(usb0Mode) usb1Mode=$(usb1Mode) video=dovefb:lcd0:$(lcd0_params),lcd1:$(lcd0 bootcmd2=usb reset; ext2load usb 0:2 0x3000000 uImage; setenv bootargs $(console) mtdparts=spi0.0:768k(u-boot),256k(uboot_env),768k(u-boot2),-(unused) rootdelay=6 cpufreq_disable pm_disab0 lcd0_params=1024x768-24@60-edid lcd1_params=1024x768-24@60-edid bootide=ide reset; ext2load ide 0:2 0x3000000 uImage; setenv bootargs $(console) $(mtdparts) cpufreq_disable lcdseamless pm_disable usb0Mode=$(usb0Mode) usb1Mode=$(usb1Mode) video=dovefb:0 bootmmc=mmcinfo 0; ext2load mmc 0:2 0x3000000 tffsg; setenv bootargs $(console) mtdparts=spi0.0:768k(u-boot),256k(uboot_env),768k(u-boot2),-(unused) cpufreq_disable pm_disable usb0Mode=$(0 console=console=ttyS0,115200 mtdparts=mtdparts=spi0.0:768k(uboot),256k(uboot_env),768k(uboot2),-(kernel) rootinit=root=initramfs init=/linuxrc lcdargs=vmalloc=384MB video=dovefb:lcd0:1024x768-24@60,lcd1:1024x768-24@60 clcd.lcd0_enable=1 clcd.lcd1_enable=1 usbargs=usb0Mode=host usb1Mode=host useNandHal=ganged bootusb=usb reset; ext2load usb 0:2 0x3000000 tffsg; setenv bootargs console=ttyS0,115200 mtdparts=spi0.0:768k(uboot),256k(uboot_env),768k(uboot2),-(kernel) root=initramfs init=/linuxrc v0 fileaddr=3000000 ethaddr=00:05:35:06:33:D4 bootcmd=run bootmmc stdin=serial stdout=lcd stderr=lcd passDramInitTag=yes mainlineLinux=yes enaMonExt=no pexMode=RC disL2Cache=no disL2Ecc=no sata_dma_mode=yes enaL2ExtraFeatures=yes enaCpuStream=no enaVpuPower=yes enaGpuPower=yes filesize=C0434 Environment size: 3887/65532 bytes
Re: Chip PC LXD8941 November 02, 2018 05:05PM |
Registered: 6 years ago Posts: 183 |
root@debian:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x000000 0x010000
Re: Chip PC LXD8941 November 02, 2018 05:50PM |
Admin Registered: 13 years ago Posts: 18,898 |
# MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x000000 0x010000 0x10000
SF: Detected MX25L1605D with page size 256, total 2097152 bytes *** env_relocate_spec **** *** Warning environment crc cae2a0b3 cae2a0b3 fffc.**** Warning: clock source is too slow.Try smaller resolution.
Re: Chip PC LXD8941 November 03, 2018 08:57AM |
Registered: 6 years ago Posts: 183 |
Re: Chip PC LXD8941 November 03, 2018 04:38PM |
Admin Registered: 13 years ago Posts: 18,898 |
dmesg | grep -i10 'mtd partition' cat /proc/cmdline cat /proc/mtd cat /ect/fw_env.config fw_setenv test 1
Re: Chip PC LXD8941 November 03, 2018 05:30PM |
Registered: 6 years ago Posts: 183 |
root@debian:~# dmesg | grep -i10 'mtd partition' [ 1.774725] console [ttyS0] enabled [ 1.781845] bootconsole [earlycon0] disabled [ 1.791580] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 22, base_baud = 10416666) is a 16550A [ 1.802556] sata_mv f10a0000.sata-host: version 1.28 [ 1.802719] sata_mv f10a0000.sata-host: slots 32 ports 1 [ 1.820391] scsi host0: sata_mv [ 1.824075] ata1: SATA max UDMA/133 irq 33 [ 1.830212] m25p80 spi0.0: found mx25l1606e, expected sst25vf080b [ 1.836291] m25p80 spi0.0: mx25l1606e (2048 Kbytes) [ 1.842711] 4 cmdlinepart partitions found on MTD device spi0.0 [ 1.848678] Creating 4 MTD partitions on "spi0.0": [ 1.853457] 0x000000000000-0x0000000c0000 : "uboot" [ 1.859933] 0x0000000c0000-0x000000100000 : "uboot_env" [ 1.866714] 0x000000100000-0x0000001c0000 : "uboot2" [ 1.873307] 0x0000001c0000-0x000000200000 : "kernel" [ 1.882598] libphy: Fixed MDIO Bus: probed [ 1.890466] libphy: orion_mdio_bus: probed [ 1.902355] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.009644] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:05:35:09:92:9a [ 2.019500] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.026020] ehci-pci: EHCI PCI platform driver root@debian:~#
root@debian:~# cat /proc/cmdline console=ttyS0,115200 root=LABEL=rootfsSD rootdelay=10 mtdparts=spi0.0:768k(uboot),256k(uboot_env),768k(uboot2),-(kernel) earlyprintk=serial root@debian:~#
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 000c0000 00001000 "uboot" mtd1: 00040000 00001000 "uboot_env" mtd2: 000c0000 00001000 "uboot2" mtd3: 00040000 00001000 "kernel" root@debian:~#
root@debian:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x000000 0x010000 0x010000 root@debian:~#
root@debian:~# fw_setenv test 1 root@debian:~# fw_printenv | grep test root@debian:~#
Re: Chip PC LXD8941 November 03, 2018 05:58PM |
Admin Registered: 13 years ago Posts: 18,898 |
# MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x000000 0x010000 0x1000
Re: Chip PC LXD8941 November 04, 2018 01:11PM |
Registered: 6 years ago Posts: 183 |
root@debian:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x000000 0x010000 0x1000 root@debian:~# root@debian:~# fw_setenv koen test root@debian:~# root@debian:~# fw_printenv | grep koen root@debian:~#
Re: Chip PC LXD8941 November 04, 2018 04:52PM |
Admin Registered: 13 years ago Posts: 18,898 |
Re: Chip PC LXD8941 November 05, 2018 04:15PM |
Admin Registered: 13 years ago Posts: 18,898 |
SF: Detected MX25L1605D with page size 256, total 2097152 bytes
Re: Chip PC LXD8941 November 05, 2018 05:49PM |
Registered: 6 years ago Posts: 183 |
[ 27.165642] m25p80 spi0.0: mx25l1605d (2048 Kbytes)
[ 1.830166] m25p80 spi0.0: found mx25l1606e, expected sst25vf080b
Re: Chip PC LXD8941 November 05, 2018 09:06PM |
Admin Registered: 13 years ago Posts: 18,898 |
johnn
Re: Debian on Chip PC LXD8941 January 03, 2019 03:27PM |
Re: Debian on Chip PC LXD8941 January 04, 2019 02:33PM |
Registered: 6 years ago Posts: 183 |
Marvin
Re: Debian on Chip PC LXD8941 February 09, 2019 06:01PM |
## Booting kernel from Legacy Image at 03000000 ... Image Name: Linux-4.20.6-mvebu-tld-1 Created: 2019-02-09 23:44:38 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4589848 Bytes = 4.4 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 04000000 ... Image Name: initramfs-4.20.6-mvebu-tld-1 Created: 2019-02-09 23:11:56 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 20276386 Bytes = 19.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... EUGENE lcd_disable EUGENE lcd_panel_disable Uncompressing Linux... done, booting the kernel. Error: invalid dtb and unrecognized/unsupported machine ID r1=0x000006fd, r2=0x00000100 r2[]=05 00 00 00 01 00 41 54 00 00 00 00 00 00 00 00 Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Berlin ffffffff Marvell Armada 39x (Device Tree) ffffffff Marvell Armada 380/385 (Device Tree) ffffffff Marvell Armada 375 (Device Tree) ffffffff Marvell Armada 370/XP (Device Tree) ffffffff Marvell Dove Please check your kernel config and/or bootloader.
Re: Debian on Chip PC LXD8941 February 09, 2019 07:52PM |
Admin Registered: 13 years ago Posts: 18,898 |
ls -lart /media/sdb1/boot
Marvin
Re: Debian on Chip PC LXD8941 February 09, 2019 08:24PM |
-rw-r--r-- 1 root root 155806 Jul 30 2017 config-4.12.4-mvebu-tld-1 -rwxr-xr-x 1 root root 4021296 Jul 30 2017 zImage-4.12.4-mvebu-tld-1 -rw------- 1 root root 4021296 Jul 30 2017 vmlinuz-4.12.4-mvebu-tld-1 -rw------- 1 root root 2615209 Jul 30 2017 System.map-4.12.4-mvebu-tld-1 -rw-r--r-- 1 root root 8525990 Jul 30 2017 linux-headers-4.12.4-mvebu-tld-1_1.0_armhf.deb -rwxr-xr-x 1 root root 4589848 Feb 6 00:15 zImage-4.20.6-mvebu-tld-1 drwxr-xr-x 6 root root 4096 Feb 6 00:26 linux-image-4.20.6_deb -rw-r--r-- 1 root root 20190276 Feb 6 00:26 linux-image-4.20.6-mvebu-tld-1_1.0_armhf.deb -rw-r--r-- 1 root root 9387008 Feb 6 00:28 linux-headers-4.20.6-mvebu-tld-1_1.0_armhf.deb drwxr-xr-x 2 root root 4096 Feb 6 01:15 dts -rw-r--r-- 1 root root 921600 Feb 6 01:18 linux-dtb-4.20.6-mvebu-tld-1.tar -rw-r--r-- 1 root root 67443 Feb 7 22:26 linux-4.20.6-mvebu-tld-1.patch -rw-r--r-- 1 root root 13880 Feb 9 13:20 dove-chip-lxd8941.dtb drwxrwxrwx 22 root root 4096 Feb 9 22:28 .. -rw-r--r-- 1 root root 174269 Feb 9 22:42 config-4.20.6-mvebu-tld-1 -rw------- 1 root root 2975213 Feb 9 22:42 System.map-4.20.6-mvebu-tld-1 -rw------- 1 root root 4589848 Feb 9 22:42 vmlinuz-4.20.6-mvebu-tld-1 -rw-r--r-- 1 root root 16636416 Feb 9 22:46 initrd.img-4.12.4-mvebu-tld-1 drwxr-xr-x 4 root root 4096 Feb 9 22:57 . -rw-r--r-- 1 root root 20276386 Feb 9 23:09 initrd.img-4.20.6-mvebu-tld-1 -rw-r--r-- 1 root root 20276450 Feb 9 23:13 uInitrd -rwxr-xr-x 1 root root 4603725 Feb 9 23:44 zImage -rw-r--r-- 1 root root 4589912 Feb 9 23:44 uImage
Re: Debian on Chip PC LXD8941 February 10, 2019 04:04AM |
Admin Registered: 13 years ago Posts: 18,898 |
-rw-r--r-- 1 root root 4589912 Feb 9 23:44 uImage