Re: Debian on WD MyCloud EX2 Ultra March 06, 2021 04:02PM |
Registered: 3 years ago Posts: 17 |
Re: Debian on WD MyCloud EX2 Ultra March 09, 2021 10:43AM |
Registered: 4 years ago Posts: 43 |
usb start fatload usb 0:1 0xa00000 uImage fatload usb 0:1 0xf00000 uInitrd bootm 0xa00000 0xf00000
Marvell» printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=root=/dev/ram console=ttyS0,115200 bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=d ovefb:lcd0:$1cd0_params cicd.lcd0_enable=$1cd0_enable cicd.lcd_panel=$1cd_panel ovefb:lcd0:$1cd0_params cicd.lcd0_enable=$1cd0_enable cicd.lcd_panel=$1cd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:ethO:none bootargs_root=root=/dev/nfs rw bootcmd=nand.e 0x02000020 0x0500000 0x0500000; nand read.e 0x2900000 0x0a00000 0x0500000; bootm 0x02000020 0x2900000 bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$s erverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$1cdO_params cicd.lcd0_enable=$1cd0_enable cicd.lcd_pane 1=$1cd_panel; bootz 0x2000000 — $fdtaddr; erverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$1cdO_params cicd.lcd0_enable=$1cd0_enable cicd.lcd_pane 1=$1cd_panel; bootz 0x2000000 — $fdtaddr; 1=$1cd_panel; bootz 0x2000000 — $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip= $ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$1cd0_params cicd.lcd0_enable=$1cd0_enable cicd.lcd_panel=$1cd_panel; bootz 0 x2000000 — $fdtaddr; $ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$1cd0_params cicd.lcd0_enable=$1cd0_enable cicd.lcd_panel=$1cd_panel; bootz 0 x2000000 — $fdtaddr; x2000000 — $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootdelay=1 cacheShare=no console=console=ttyS0,115200 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:1a:2c:36 ethlmtu=1500 eth2addr=00:50:43:1a:33:36 eth2mtu=1500 eth3addr=00:50:43:2c:33:la eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:33:2c:36 ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-38x—modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcdO_params=640x480-16@60 lcd_pane1=0 loadaddr=0x02000000 loads_echo=0 mtddevname=u—boot mtddevnum=0 mtdids=nand0=armada—nand mtdparts=mtdparts=armada—nand:5m(u—boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@2Ond0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm—armadaxp—db:default.arm—armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath,/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scrive=1 usbType=3 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 3216/524284 bytes Marvell»
Re: Debian on WD MyCloud EX2 Ultra March 09, 2021 05:16PM |
Admin Registered: 13 years ago Posts: 18,821 |
bootargs=root=/dev/ram console=ttyS0,115200
setenv bootargs 'root=/dev/ram console=ttyS0,115200 earlyprintk=serial'
Re: Debian on WD MyCloud EX2 Ultra March 10, 2021 05:10AM |
Registered: 4 years ago Posts: 43 |
Quote
bodhi Wrote:
-------------------------------------------------------
> That's probably not enough. You need to use my
> kernel config and patches to make sure that it
> will work.
Quote
> And also use earlyprintk to see more info during
> boot.
>
> Current:
>> bootargs=root=/dev/ram console=ttyS0,115200 >>
> Should be
>> setenv bootargs 'root=/dev/ram > console=ttyS0,115200 earlyprintk=serial' >
Device UUID: 34375840-037F—B8C1-2285-24A3009F87FF Service UUID: FFEO RX UUID: FFE1 TX UUID: FFE1 Connecting Successfully connected to BLE device. Enable HD1 Enable HD2 et: I port I Interface PHY address 1 egiga0 I RGMII In—Band 1 egigal RGMII In—Band 1 egiga2 I SGMII Ox00 egiga0, egigal, egiga2 [PRIME] Hit any key to stop autoboot: 0 nand — NAND sub—system Usage: nand info — show available NAND devices nand device [dev] — show or set current device nand read — addr off partition size nand write — addr off partition size read/write 'size' bytes starting at offset 'off' to/from memory address 'addr', skipping bad blocks. nand read. raw — addr offlpartition [count] nand write. raw — addr offlpartition [count] Use read.raw/write.raw to avoid ECC and access the flash as—is. nand write.trimffs — addr off partition size write 'size' bytes starting at offset 'off' from memory address 'addr', skipping bad blocks and dropping any pages at the end of eraseblocks that contain only OxFF nand erase[.spread] [clean] off size — erase 'size' bytes from offset 'off' With '.spread', erase enough for given file size, otherwise, 'size' includes skipped bad blocks. nand erase.part [clean] partition — erase entire mtd partition' nand erase.chip [clean] — erase entire chip' nand bad — show bad blocks nand dump[.00b] off — dump page nand scrub [—y] off size 1 scrub.part partition 1 scrub.chip really clean NAND erasing bad blocks (UNSAFE) nand markbad off [...] — mark bad block(s) at offset (UNSAFE) nand biterr off — make a bit error at offset (UNSAFE) AND read: device 0 offset 0xa00000, size 0x500000 5242880 bytes read: OK •# Booting image at 02000020 ... AND read: device 0 offset 0xc800800, size 0xf00000 15728640 bytes read: OK •# Booting image at 00a00000 •# Booting kernel from Legacy Image at 00a00000 Image Name: Linux-382 Created: 2015-08-02 3:54:03 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4093292 Bytes = 3.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum OK •# Loading init Ramdisk from Legacy Image at 00e00000 Image Name: Ramdisk Created: 2015-10-05 5:02:44 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7010744 Bytes = 6.7 MiB Load Address: 00e00000 Entry Point: 00e00000 Verifying Checksum OK Loading Kernel Image ... OK OK Starting kernel ...
Re: Debian on WD MyCloud EX2 Ultra March 10, 2021 05:27AM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Debian on WD MyCloud EX2 Ultra March 10, 2021 05:46AM |
Registered: 4 years ago Posts: 43 |
Re: Debian on WD MyCloud EX2 Ultra March 10, 2021 07:33AM |
Registered: 4 years ago Posts: 43 |
Device UUID: 34375840-037F—B8C1-2285-24A3009F87FF Service UUID: FFEO RX UUID: FFE1 TX UUID: FFE1 Connecting Successfully connected to BLE device. Enable HD2 et: 1 port I Interface PHY address 1 1 egiga0 I RGMII In—Band 1 egigal RGMII In—Band 1 egiga2 I SGMII I 0x00 egiga0, egigal, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell» usb start (Re)start USB... USBO: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Marvell» fatload usb 0:1 0x02000020 uImage reading uImage 5159667 bytes read in 287 ms (17.1 MiB/s) Marvell» fatload usb 0:1 0x2900000 uInitrd reading uInitrd 4830114 bytes read in 265 ms (17.4 MiB/s) Marvell» bootm 0x02000020 0x2900000 •# Booting image at 02000020 ... •# Booting kernel from Legacy Image at 02000020 ... Image Name: Kernel—v5.11.5 Created: 2021-03-09 13:50:46 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5159603 Bytes = 4.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum OK •# Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: BusyBox v1.31 Created: 2020-04-21 13:35:00 UTC Image Type: ARM Linux RAMDisk Image (lzma compressed) Data Size: 4830050 Bytes = 4.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum OK
Re: Debian on WD MyCloud EX2 Ultra March 10, 2021 04:25PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Debian on WD MyCloud EX2 Ultra March 11, 2021 08:31AM |
Registered: 4 years ago Posts: 43 |
Device UUID: 34375840-037F—B8C1-2285-24A3009F87FF Service UUID: FFEO RX UUID: FFE1 TX UUID: FFE1 Connecting Successfully connected to BLE device. et: 1 port Interface 1 PHY address 1 1 1 egiga0 RGMII 1 In—Band 1 egigal RGMII 1 In—Band 1 egiga2 SGMII 1 0x00 egiga0, egigal, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell» usb start (Re)start USB... USBO: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Marvell» fatload usb 0:1 0x02000020 uImage.bodhi reading uImage.bodhi 5143307 bytes read in 289 ms (17 MiB/s) Marvell» bootm 0x02000020 •# Booting image at 02000020 ... •# Booting kernel from Legacy Image at 02000020 ... Image Name: Linux-5.10.7—mvebu—tld-1 Created: 2021-03-11 9:23:54 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5143243 Bytes = 4.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum OK
Re: Debian on WD MyCloud EX2 Ultra March 11, 2021 10:12PM |
Admin Registered: 13 years ago Posts: 18,821 |
printenv
Re: Debian on WD MyCloud EX2 Ultra March 12, 2021 02:22AM |
Registered: 4 years ago Posts: 43 |
Connecting Successfully connected to BLE device. Enable HD2 Net: 1 port I Interface I PHY address 1 egiga0 RGMII In—Band 1 egigal RGMII In—Band 1 egiga2 I SGMII I 0x00 egiga0, egigal, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell» printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=root=/dev/ram console=ttyS0,115200 earlyprintk=serial bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=d ovefb:lcd0:$lcd0_params cicd.lcd0_enable=$lcd0_enable cicd.lcd_panel=$1cd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:ethO:none bootargs_root=root=/dev/nfs rw bootcmd=nand.e 0x02000020 0x0500000 0x0500000; nand read.e 0x2900000 0x0a00000 0x0500000; bootm 0x02000020 0x2900000 bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$s erverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$1cd0_params cicd.lcd0_enable=$lcd0_enable cicd.lcd_pane l=$lcd_panel; bootz 0x2000000 — $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip= $ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params cicd.lcd0_enable=$1cd0_enable cicd.lcd_panel=$lcd_panel; bootz 0 x2000000 — $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootdelay=1 cacheShare=no console=console=ttyS0,115200 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:1a:2c:36 ethlmtu=1500 eth2addr=00:50:43:1a:33:36 eth2mtu=1500 eth3addr=00:50:43:2c:33:la eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:33:2c:36 ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-38x—modular.dtb filesize=12 ide_path=i image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_pane1=0 loadaddr=0x02000000 loads_echo=0 mtddevname=u—boot mtddevnum=0 mtdids=nand0=armada—nand mtdparts=mtdparts=armada—nand:5m(u—boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15tret0 sbOMode=host usbActive=1 usbType=3 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 3235/524284 bytes Marvell» usb start (Re)start USB... USBO: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Marvell» fattoad usb 0:1 0x02000020 uImage.bodhi reading uImage.bodhi 5143307 bytes read in 283 ms (17.3 MiB/s) Marvell» bootm 0x02000020 •# Booting image at 02000020 ... •# Booting kernel from Legacy Image at 02000020 ... Image Name: Linux-5.10.7—mvebu—tld-1 Created: 2021-03-11 9:23:54 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5143243 Bytes = 4.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum OK
Re: Debian on WD MyCloud EX2 Ultra March 12, 2021 04:55PM |
Admin Registered: 13 years ago Posts: 18,821 |
setenv fdt_skip_update yes
Re: Debian on WD MyCloud EX2 Ultra March 13, 2021 01:40AM |
Registered: 4 years ago Posts: 43 |
Device UUID: 34375840-037F—B8C1-2285-24A3009F87FF Service UUID: FFEO RX UUID: FFE1 TX UUID: FFE1 Connecting Successfully connected to BLE device. Enable HD2 Net: port I Interface 1 PHY address I egiga0 I RGMII 1 In—Band I egigal RGMII 1 In—Band I egiga2 I SGMII 1 0x00 egiga0, egigal, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell» printenv fdt_skip_update fdt_skip_update=no Marvell» setenv fdt_skip_update yes Marvell» printenv fdt_skip_update fdt_skip_update=yes Marvell» usb start (Re)start USB... USBO: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Marvell» fatload usb 0:1 0x02000020 uImage.bodhi reading uImage.bodhi 5143307 bytes read in 284 ms (17.3 MiB/s) Marvell» bootm 0x02000020 ## Booting image at 02000020 ... ## Booting kernel from Legacy Image at 02000020 ... Image Name: Linux-5.10.7—mvebu—tld-1 Created: 2021-03-11 9:23:54 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5143243 Bytes = 4.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum OK
Re: Debian on WD MyCloud EX2 Ultra March 13, 2021 04:09PM |
Admin Registered: 13 years ago Posts: 18,821 |
fdt_skip_update=no
fatload usb 0:1 0x02000000 uImage stenv fdt_skip_update yes setenv bootargs 'root=/dev/sda1 console=ttyS0,115200' bootm 0x02000000and
fatload usb 0:1 0x02000000 uImage stenv fdt_skip_update yes setenv bootargs 'root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial' bootm 0x02000000
Re: Debian on WD MyCloud EX2 Ultra March 19, 2021 02:59PM |
Registered: 4 years ago Posts: 43 |
Re: Debian on WD MyCloud EX2 Ultra March 19, 2021 03:52PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Debian on WD MyCloud EX2 Ultra March 24, 2021 04:06AM |
Registered: 4 years ago Posts: 43 |
Enable HD1 Enable HD2 et: I port I Interface I PHY address 1 egiga0 I RGMII In—Band 1 egigal RGMII In—Band 1 egiga2 I SGMII 0x00 egiga0, egigal, egiga2 [PRIME] Hit any key to stop autoboot: 0 nand — NAND sub—system Usage: nand info — show available NAND devices nand device [dev] — show or set current device nand read — addr off partition size nand write — addr offipartition size read/write 'size' bytes starting at offset 'off' to/from memory address 'addr', skipping bad blocks. nand read. raw — addr offlpartition [count] nand write. raw — addr off partition [count] Use read.raw/write.raw to avoid ECC and access the flash as—is. nand write.trimffs — addr offipartition size write 'size' bytes starting at offset 'off' from memory address 'addr', skipping bad blocks and dropping any pages at the end of eraseblocks that contain only OxFF nand erase[.spread] [clean] off size — erase 'size' bytes from offset 'off' With '.spread', erase enough for given file size, otherwise, 'size' includes skipped bad blocks. nand erase.part [clean] partition — erase entire mtd partition' nand erase.chip [clean] — erase entire chip' nand bad — show bad blocks nand dump[.00b] off — dump page nand scrub [—y] off size 1 scrub.part partition 1 scrub.chip really clean NAND erasing bad blocks (UNSAFE) nand markbad off [...] — mark bad block(s) at offset (UNSAFE) nand biterr off — make a bit error at offset (UNSAFE) AND read: device 0 offset 0xa00000, size 0x500000 5242880 bytes read: OK •# Booting image at 02000020 ... AND read: device 0 offset 0xc800800, size 0xf00000 15728640 bytes read: OK •# Booting image at 00a00000 •# Booting kernel from Legacy Image at 00a00000 Image Name: Linux-382 Created: 2015-08-02 3:54:03 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4093292 Bytes = 3.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum OK •# Loading init Ramdisk from Legacy Image at 00e00000 Image Name: Ramdisk Created: 2015-10-05 5:02:44 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7010744 Bytes = 6.7 MiB Load Address: 00e00000 Entry Point: 00e00000 Verifying Checksum OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU Ox0 Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 3.10.39 (kman@kmachine) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALI GN) ) #1 SMP Sun Aug 2 11:53:57 CST 2015 2014T30p5 Build—git3e9fe59 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 385 Development Board bootconsole [earlycon0] enabled Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 1 pages/cpu @c09d0000 s8320 r8192 d16256 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32737 Kernel command line: root=/dev/ram console=ttyS0,115200 earlyprintk=serial PID hash table entries: 4096 (order: —1, 16384 bytes)
Re: Debian on WD MyCloud EX2 Ultra April 08, 2021 04:15AM |
Registered: 4 years ago Posts: 43 |
Re: Debian on WD MyCloud EX2 Ultra April 08, 2021 04:27PM |
Admin Registered: 13 years ago Posts: 18,821 |
Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU Ox0 Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 3.10.39 (kman@kmachine) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALI GN) ) #1 SMP Sun Aug 2 11:53:57 CST 2015 2014T30p5 Build—git3e9fe59 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 385 Development Board bootconsole [earlycon0] enabled Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 1 pages/cpu @c09d0000 s8320 r8192 d16256 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32737 Kernel command line: root=/dev/ram console=ttyS0,115200 earlyprintk=serial PID hash table entries: 4096 (order: —1, 16384 bytes)
Kernel command line: root=/dev/ram console=ttyS0,115200 earlyprintk=serial
root=/dev/sda1
Re: Debian on WD MyCloud EX2 Ultra November 24, 2022 01:53PM |
Registered: 1 year ago Posts: 142 |
Marvell>> fatload usb 0:1 0x02000000 boot_mio/uImage reading boot_mio/uImage 3886355 bytes read in 153 ms (24.2 MiB/s) Marvell>> setenv fdt_skip_update yes Marvell>> setenv bootargs root=/dev/sda2 console=ttyS0,115200 earlyprintk=serial Marvell>> bootm 0x02000000 ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: WDMC-Gen2 Created: 2022-11-23 15:00:20 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3886291 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK
Re: Debian on WD MyCloud EX2 Ultra November 24, 2022 02:39PM |
Registered: 1 year ago Posts: 142 |
Marvell>> usb start (Re)start USB... USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Marvell>> fatload usb 0:1 0x02000000 boot/uimage reading boot/uimage 5076006 bytes read in 195 ms (24.8 MiB/s) Marvell>> setenv fdt_skip_update yes Marvell>> setenv bootargs root=/dev/sda2 console=ttyS0,115200 earlyprintk=serial Marvell>> bootm 0x02000000 ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-5.2.9-mvebu-tld-1 Created: 2022-11-24 20:26:21 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5075942 Bytes = 4.8 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK
Re: Debian on WD MyCloud EX2 Ultra January 18, 2023 04:08AM |
Registered: 1 year ago Posts: 12 |
Re: Debian on WD MyCloud EX2 Ultra January 18, 2023 02:35PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Debian on WD MyCloud EX2 Ultra January 19, 2023 10:36AM |
Registered: 1 year ago Posts: 12 |
Re: Debian on WD MyCloud EX2 Ultra January 19, 2023 04:26PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
https://wd.hides.su/wdnas.el8.website/WDMyCloud-Ex2-Ultra/Debian-linux_4.14.4/_info_EN.txt
dd if=/dev/zero of=/dev/mtdblock1
dd if=uImage of=/dev/mtdblock1
dd if=/dev/zero of=/dev/mtdblock2
dd if=uRamdisk of=/dev/mtdblock2
Re: Debian on WD MyCloud EX2 Ultra January 20, 2023 02:26AM |
Registered: 1 year ago Posts: 12 |
Re: Debian on WD MyCloud EX2 Ultra January 20, 2023 03:19PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
Updated 09 Nov 2022:
Kernel 6.0.7-mvebu-tld-1 package has been uploaded.
New/Updated in this release:
- General kernel upgrade.
Latest Linux kernel 6.x general release information can be found at:
LinuxChanges log
Download at Dropbox
linux-6.0.7-mvebu-tld-1-bodhi.tar.bz2
md5:
bfb1d7cf103f501b991e21b9886db4f6
sha256:
dcf50e17352f7d84ab606abdef374ec0d3db1c39b242c6ae7924b7283edc3ead
As always, please check the hash of your download!
There are 6 files in this tarball:
Quote
linux-image-6.0.7-mvebu-tld-1_1.0_armhf.deb
linux-headers-6.0.7-mvebu-tld-1_1.0_armhf.deb
zImage-6.0.7-mvebu-tld-1
config-6.0.7-mvebu-tld-1
linux-dtb-6.0.7-mvebu-tld-1.tar
linux-6.0.7-mvebu-tld-1.patch
Installation
NOTE: the following steps are for a general kernel upgrade. For initial installation, please see "Installation Instruction for specific boxes" in the thread description at the top of this release thread.
1. Backup your current zImage, uImage, and uInitrd. In the /boot directory, these are files for your current kernel (xx.xx.xx is the version number):
uInitrd
uImage
zImage-xx.xx.xx-mvebu-xxx
initrd.img-xx.xx.xx-mvebu-xxx
System.map-xx.xx.xx-mvebu-xxx
vmlinuz-xx.xx.xx-mvebu-xxx
config-xx.xx.xx-mvebu-xxx
dts/
2. Extract the kernel and the DTB files in the archive:
cd /boot
tar -xjf linux-6.0.7-mvebu-tld-1-bodhi.tar.bz2
tar -xf linux-dtb-6.0.7-mvebu-tld-1.tar
3. And install it with dpkg. Remove flash-kernel first to avoid potential problem (if flash-kernel was not installed then you'll see some error output):
cd /boot
apt-get remove flash-kernel
dpkg -i linux-image-6.0.7-mvebu-tld-1_1.0_armhf.deb
4. Create uImage and uInitrd (kernel file initrd.img-6.0.7-mvebu-tld-1 was generated by dpkg in step 3). I am using the Zyxel NAS326 as an example here. Please replace armada-380-zyxel-nas326.dtb below with the appropriate DTB name for your box.
cd /boot
cp -a zImage-6.0.7-mvebu-tld-1 zImage.fdt
cat dts/armada-380-zyxel-nas326.dtb >> zImage.fdt
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.0.7-mvebu-tld-1 -d zImage.fdt uImage
mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-6.0.7-mvebu-tld-1 -d initrd.img-6.0.7-mvebu-tld-1 uInitrd
5. The new uImage and uInitrd files should be created in /boot directory now. You're ready to reboot the system:
sync
sync
sync
shutdown -r now