|
Re: Debian on WD MyCloud EX2 Ultra March 06, 2021 04:02PM |
Registered: 4 years ago Posts: 17 |
|
Re: Debian on WD MyCloud EX2 Ultra March 09, 2021 10:43AM |
Registered: 4 years ago Posts: 43 |
bodhi Wrote:
-------------------------------------------------------
> @dtd,
>
> Here is the revised version of the DTS and its
> DTB. I've changed the file name to be consistent
> with what we have currently. I also change the
> machine name in the DTS (do a diff with your
> version to see the changes).
>
> @all,
>
> Please try this armada-385-wd-ex2-ultra.dtb. I've
> added a fix to keep the persistent MAC address
> (local MAC address will not be generated by the
> kernel).
Thank you, bodhi!
I have compiled Kernel 5.11.5 for this box using your new .dtd and .dts files. I had to take off IPv6 support out of kernel in order for the final file fit into 5Mb. But I seem to mess up my u-boot and bootargs. My old instruction on how to flash u-boot doesn’t work.
And even if I do:
it just hangs, so there is no boot log.
Here is my printenv:
Edited 2 time(s). Last edit at 03/09/2021 10:57AM by vzhilov.
-------------------------------------------------------
> @dtd,
>
> Here is the revised version of the DTS and its
> DTB. I've changed the file name to be consistent
> with what we have currently. I also change the
> machine name in the DTS (do a diff with your
> version to see the changes).
>
> @all,
>
> Please try this armada-385-wd-ex2-ultra.dtb. I've
> added a fix to keep the persistent MAC address
> (local MAC address will not be generated by the
> kernel).
Thank you, bodhi!
I have compiled Kernel 5.11.5 for this box using your new .dtd and .dts files. I had to take off IPv6 support out of kernel in order for the final file fit into 5Mb. But I seem to mess up my u-boot and bootargs. My old instruction on how to flash u-boot doesn’t work.
And even if I do:
usb start fatload usb 0:1 0xa00000 uImage fatload usb 0:1 0xf00000 uInitrd bootm 0xa00000 0xf00000
it just hangs, so there is no boot log.
Here is my printenv:
Marvell» printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=root=/dev/ram console=ttyS0,115200 bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=d ovefb:lcd0:$1cd0_params cicd.lcd0_enable=$1cd0_enable cicd.lcd_panel=$1cd_panel ovefb:lcd0:$1cd0_params cicd.lcd0_enable=$1cd0_enable cicd.lcd_panel=$1cd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:ethO:none bootargs_root=root=/dev/nfs rw bootcmd=nand.e 0x02000020 0x0500000 0x0500000; nand read.e 0x2900000 0x0a00000 0x0500000; bootm 0x02000020 0x2900000 bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$s erverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$1cdO_params cicd.lcd0_enable=$1cd0_enable cicd.lcd_pane 1=$1cd_panel; bootz 0x2000000 — $fdtaddr; erverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$1cdO_params cicd.lcd0_enable=$1cd0_enable cicd.lcd_pane 1=$1cd_panel; bootz 0x2000000 — $fdtaddr; 1=$1cd_panel; bootz 0x2000000 — $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip= $ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$1cd0_params cicd.lcd0_enable=$1cd0_enable cicd.lcd_panel=$1cd_panel; bootz 0 x2000000 — $fdtaddr; $ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$1cd0_params cicd.lcd0_enable=$1cd0_enable cicd.lcd_panel=$1cd_panel; bootz 0 x2000000 — $fdtaddr; x2000000 — $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootdelay=1 cacheShare=no console=console=ttyS0,115200 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:1a:2c:36 ethlmtu=1500 eth2addr=00:50:43:1a:33:36 eth2mtu=1500 eth3addr=00:50:43:2c:33:la eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:33:2c:36 ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-38x—modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcdO_params=640x480-16@60 lcd_pane1=0 loadaddr=0x02000000 loads_echo=0 mtddevname=u—boot mtddevnum=0 mtdids=nand0=armada—nand mtdparts=mtdparts=armada—nand:5m(u—boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@2Ond0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm—armadaxp—db:default.arm—armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath,/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scrive=1 usbType=3 vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 3216/524284 bytes Marvell»
Edited 2 time(s). Last edit at 03/09/2021 10:57AM by vzhilov.
|
Re: Debian on WD MyCloud EX2 Ultra March 09, 2021 05:16PM |
Admin Registered: 14 years ago Posts: 19,422 |
vzhilov,
> I have compiled
> Kernel
> 5.11.5 for this box using your new .dtd and
> .dts files.
That's probably not enough. You need to use my kernel config and patches to make sure that it will work.
And also use earlyprintk to see more info during boot.
Current:
Should be
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I have compiled
> Kernel
> 5.11.5 for this box using your new .dtd and
> .dts files.
That's probably not enough. You need to use my kernel config and patches to make sure that it will work.
And also use earlyprintk to see more info during boot.
Current:
bootargs=root=/dev/ram console=ttyS0,115200
Should be
setenv bootargs 'root=/dev/ram console=ttyS0,115200 earlyprintk=serial'
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on WD MyCloud EX2 Ultra March 10, 2021 05:10AM |
Registered: 4 years ago Posts: 43 |
Quote
bodhi Wrote:
-------------------------------------------------------
> That's probably not enough. You need to use my
> kernel config and patches to make sure that it
> will work.
Oh, yes, you are right. Is that something new?
Quote
> And also use earlyprintk to see more info during
> boot.
>
> Current:
>> bootargs=root=/dev/ram console=ttyS0,115200 >>
> Should be
>> setenv bootargs 'root=/dev/ram > console=ttyS0,115200 earlyprintk=serial' >
Thank you, I did that. But still no luck, it just fails to recover partition:
Device UUID: 34375840-037F—B8C1-2285-24A3009F87FF
Service UUID: FFEO
RX UUID: FFE1
TX UUID: FFE1
Connecting
Successfully connected to BLE device.
Enable HD1
Enable HD2
et:
I port I Interface PHY address
1 egiga0 I RGMII In—Band
1 egigal RGMII In—Band
1 egiga2 I SGMII Ox00
egiga0, egigal, egiga2 [PRIME]
Hit any key to stop autoboot: 0
nand — NAND sub—system
Usage:
nand info — show available NAND devices
nand device [dev] — show or set current device
nand read — addr off partition size
nand write — addr off partition size
read/write 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
nand read. raw — addr offlpartition [count]
nand write. raw — addr offlpartition [count]
Use read.raw/write.raw to avoid ECC and access the flash as—is.
nand write.trimffs — addr off partition size
write 'size' bytes starting at offset 'off' from memory address
'addr', skipping bad blocks and dropping any pages at the end
of eraseblocks that contain only OxFF
nand erase[.spread] [clean] off size — erase 'size' bytes from offset 'off'
With '.spread', erase enough for given file size, otherwise,
'size' includes skipped bad blocks.
nand erase.part [clean] partition — erase entire mtd partition'
nand erase.chip [clean] — erase entire chip'
nand bad — show bad blocks
nand dump[.00b] off — dump page
nand scrub [—y] off size 1 scrub.part partition 1 scrub.chip
really clean NAND erasing bad blocks (UNSAFE)
nand markbad off [...] — mark bad block(s) at offset (UNSAFE)
nand biterr off — make a bit error at offset (UNSAFE)
AND read: device 0 offset 0xa00000, size 0x500000
5242880 bytes read: OK
•# Booting image at 02000020 ...
AND read: device 0 offset 0xc800800, size 0xf00000
15728640 bytes read: OK
•# Booting image at 00a00000
•# Booting kernel from Legacy Image at 00a00000
Image Name: Linux-382
Created: 2015-08-02 3:54:03 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4093292 Bytes = 3.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum OK
•# Loading init Ramdisk from Legacy Image at 00e00000
Image Name: Ramdisk
Created: 2015-10-05 5:02:44 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7010744 Bytes = 6.7 MiB
Load Address: 00e00000
Entry Point: 00e00000
Verifying Checksum OK
Loading Kernel Image ... OK
OK
Starting kernel ...
I have flashed new OS 5 from WD before doing all that, could that mess all up?
|
Re: Debian on WD MyCloud EX2 Ultra March 10, 2021 05:27AM |
Admin Registered: 14 years ago Posts: 19,422 |
vzhilov,
> I have flashed new OS 5 from WD before doing all
> that, could that mess all up?
Yes, the kernel files are ones from stock FW. So you need to reflash the new build uImage and uInitrd to NAND ( if that's what you want to boot from).
OTOH, if you only want to boot kernel from from USB/HDD rootfs then the u-boot envs were no longer good after that OS5 flash (bootcmd was reset).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I have flashed new OS 5 from WD before doing all
> that, could that mess all up?
Yes, the kernel files are ones from stock FW. So you need to reflash the new build uImage and uInitrd to NAND ( if that's what you want to boot from).
OTOH, if you only want to boot kernel from from USB/HDD rootfs then the u-boot envs were no longer good after that OS5 flash (bootcmd was reset).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on WD MyCloud EX2 Ultra March 10, 2021 05:46AM |
Registered: 4 years ago Posts: 43 |
|
Re: Debian on WD MyCloud EX2 Ultra March 10, 2021 07:33AM |
Registered: 4 years ago Posts: 43 |
Device UUID: 34375840-037F—B8C1-2285-24A3009F87FF
Service UUID: FFEO
RX UUID: FFE1
TX UUID: FFE1
Connecting
Successfully connected to BLE device.
Enable HD2
et:
1 port I Interface PHY address
1
1 egiga0 I RGMII In—Band
1 egigal RGMII In—Band
1 egiga2 I SGMII I 0x00
egiga0, egigal, egiga2 [PRIME]
Hit any key to stop autoboot: 0
Marvell» usb start
(Re)start USB...
USBO: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell» fatload usb 0:1 0x02000020 uImage
reading uImage
5159667 bytes read in 287 ms (17.1 MiB/s)
Marvell» fatload usb 0:1 0x2900000 uInitrd
reading uInitrd
4830114 bytes read in 265 ms (17.4 MiB/s)
Marvell» bootm 0x02000020 0x2900000
•# Booting image at 02000020 ...
•# Booting kernel from Legacy Image at 02000020 ...
Image Name: Kernel—v5.11.5
Created: 2021-03-09 13:50:46 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5159603 Bytes = 4.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum OK
•# Loading init Ramdisk from Legacy Image at 02900000 ...
Image Name: BusyBox v1.31
Created: 2020-04-21 13:35:00 UTC
Image Type: ARM Linux RAMDisk Image (lzma compressed)
Data Size: 4830050 Bytes = 4.6 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum OK
Nothing else happens, even with your kernel
Edited 2 time(s). Last edit at 03/10/2021 07:37AM by vzhilov.
|
Re: Debian on WD MyCloud EX2 Ultra March 10, 2021 04:25PM |
Admin Registered: 14 years ago Posts: 19,422 |
vzhilov,
If you can no longer boot into your RAID rootfs (I recall you are using RAID), or HDD rootfs.
Try booting the rootfs Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2 on USB. See if you can get back to a working system first. And use
- the zImage-5.10.7-mvebu-tld-1 (from linux-5.10.7-mvebu-tld-1-bodhi.tar.bz2)
- the latest DTB (from linux-5.10.7-mvebu-tld-1-bodhi.tar.bz2)
- The uInitrd can be from Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2
This will give you an idea what's working.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
If you can no longer boot into your RAID rootfs (I recall you are using RAID), or HDD rootfs.
Try booting the rootfs Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2 on USB. See if you can get back to a working system first. And use
- the zImage-5.10.7-mvebu-tld-1 (from linux-5.10.7-mvebu-tld-1-bodhi.tar.bz2)
- the latest DTB (from linux-5.10.7-mvebu-tld-1-bodhi.tar.bz2)
- The uInitrd can be from Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2
This will give you an idea what's working.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on WD MyCloud EX2 Ultra March 11, 2021 08:31AM |
Registered: 4 years ago Posts: 43 |
If I would get a single message for a clue I will be happy
And then total silence
Edited 1 time(s). Last edit at 03/11/2021 08:32AM by vzhilov.
Device UUID: 34375840-037F—B8C1-2285-24A3009F87FF
Service UUID: FFEO
RX UUID: FFE1
TX UUID: FFE1
Connecting
Successfully connected to BLE device.
et:
1 port Interface 1 PHY address
1 1
1 egiga0 RGMII 1 In—Band
1 egigal RGMII 1 In—Band
1 egiga2 SGMII 1 0x00
egiga0, egigal, egiga2 [PRIME]
Hit any key to stop autoboot: 0
Marvell» usb start
(Re)start USB...
USBO: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell» fatload usb 0:1 0x02000020 uImage.bodhi
reading uImage.bodhi
5143307 bytes read in 289 ms (17 MiB/s)
Marvell» bootm 0x02000020
•# Booting image at 02000020 ...
•# Booting kernel from Legacy Image at 02000020 ...
Image Name: Linux-5.10.7—mvebu—tld-1
Created: 2021-03-11 9:23:54 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5143243 Bytes = 4.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum OK
And then total silence
Edited 1 time(s). Last edit at 03/11/2021 08:32AM by vzhilov.
|
Re: Debian on WD MyCloud EX2 Ultra March 11, 2021 10:12PM |
Admin Registered: 14 years ago Posts: 19,422 |
At this point:
> Hit any key to stop autoboot: 0
and do the rest like you did to boot the box from USB.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Hit any key to stop autoboot: 0
printenv
and do the rest like you did to boot the box from USB.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on WD MyCloud EX2 Ultra March 12, 2021 02:22AM |
Registered: 4 years ago Posts: 43 |
Connecting
Successfully connected to BLE device.
Enable HD2
Net:
1 port I Interface I PHY address
1 egiga0 RGMII In—Band
1 egigal RGMII In—Band
1 egiga2 I SGMII I 0x00
egiga0, egigal, egiga2 [PRIME]
Hit any key to stop autoboot: 0
Marvell» printenv
CASset=max
MALLOC_len=5
MPmode=SMP
autoload=no
baudrate=115200
boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr
bootargs=root=/dev/ram console=ttyS0,115200 earlyprintk=serial
bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=d
ovefb:lcd0:$lcd0_params cicd.lcd0_enable=$lcd0_enable cicd.lcd_panel=$1cd_panel
bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:ethO:none
bootargs_root=root=/dev/nfs rw
bootcmd=nand.e 0x02000020 0x0500000 0x0500000; nand read.e 0x2900000 0x0a00000 0x0500000; bootm 0x02000020 0x2900000
bootcmd_auto=stage_boot $boot_order
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$s
erverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$1cd0_params cicd.lcd0_enable=$lcd0_enable cicd.lcd_pane
l=$lcd_panel; bootz 0x2000000 — $fdtaddr;
bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=
$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params cicd.lcd0_enable=$1cd0_enable cicd.lcd_panel=$lcd_panel; bootz 0
x2000000 — $fdtaddr;
bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot
bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000;
bootdelay=1
cacheShare=no
console=console=ttyS0,115200
device_partition=0:1
disaMvPnp=no
eeeEnable=no
enaClockGating=no
enaCpuStream=no
enaFPU=yes
enaMonExt=no
enaWrAllo=no
eth1addr=00:50:43:1a:2c:36
ethlmtu=1500
eth2addr=00:50:43:1a:33:36
eth2mtu=1500
eth3addr=00:50:43:2c:33:la
eth3mtu=1500
ethact=egiga2
ethaddr=00:50:43:33:2c:36
ethmtu=1500
ethprime=egiga2
fdt_addr=2040000
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-38x—modular.dtb
filesize=12
ide_path=i
image_name=uImage
initrd_name=uInitrd
ipaddr=192.168.11.110
kernel_addr_r=2080000
lcd0_enable=0
lcd0_params=640x480-16@60
lcd_pane1=0
loadaddr=0x02000000
loads_echo=0
mtddevname=u—boot
mtddevnum=0
mtdids=nand0=armada—nand
mtdparts=mtdparts=armada—nand:5m(u—boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15tret0
sbOMode=host
usbActive=1
usbType=3
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 3235/524284 bytes
Marvell» usb start
(Re)start USB...
USBO: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell» fattoad usb 0:1 0x02000020 uImage.bodhi
reading uImage.bodhi
5143307 bytes read in 283 ms (17.3 MiB/s)
Marvell» bootm 0x02000020
•# Booting image at 02000020 ...
•# Booting kernel from Legacy Image at 02000020 ...
Image Name: Linux-5.10.7—mvebu—tld-1
Created: 2021-03-11 9:23:54 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5143243 Bytes = 4.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum OK
Edited 1 time(s). Last edit at 03/12/2021 02:23AM by vzhilov.
|
Re: Debian on WD MyCloud EX2 Ultra March 12, 2021 04:55PM |
Admin Registered: 14 years ago Posts: 19,422 |
vzhilov.
Set this env before booting:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Set this env before booting:
setenv fdt_skip_update yes
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on WD MyCloud EX2 Ultra March 13, 2021 01:40AM |
Registered: 4 years ago Posts: 43 |
Device UUID: 34375840-037F—B8C1-2285-24A3009F87FF
Service UUID: FFEO
RX UUID: FFE1
TX UUID: FFE1
Connecting
Successfully connected to BLE device.
Enable HD2
Net:
port I Interface 1 PHY address
I egiga0 I RGMII 1 In—Band
I egigal RGMII 1 In—Band
I egiga2 I SGMII 1 0x00
egiga0, egigal, egiga2 [PRIME]
Hit any key to stop autoboot: 0
Marvell» printenv fdt_skip_update
fdt_skip_update=no
Marvell» setenv fdt_skip_update yes
Marvell» printenv fdt_skip_update
fdt_skip_update=yes
Marvell» usb start
(Re)start USB...
USBO: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell» fatload usb 0:1 0x02000020 uImage.bodhi
reading uImage.bodhi
5143307 bytes read in 284 ms (17.3 MiB/s)
Marvell» bootm 0x02000020
## Booting image at 02000020 ...
## Booting kernel from Legacy Image at 02000020 ...
Image Name: Linux-5.10.7—mvebu—tld-1
Created: 2021-03-11 9:23:54 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5143243 Bytes = 4.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum OK
Same thing, unfortunately. Nothing after I try to boot the kernel.
|
Re: Debian on WD MyCloud EX2 Ultra March 13, 2021 04:09PM |
Admin Registered: 14 years ago Posts: 19,422 |
vzhilov,
Indeed it is qutite a strange behavior. Your envs don't have any thing that stands out that could be wrong other than fdt_skip_update. This is a quite important setting, which must be set to yes when running with modern kernel DTB.
I'd suggest:
- Go back a few kernel versions. Keep using an older and older uImage until it can boot.
- Boot with a normal bootargs (no RAID). Alternately with earlyprintk and without. Load to 0x02000000 (instead of 0x02000020 as stock does):
So for each uImage try 2 boots
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Indeed it is qutite a strange behavior. Your envs don't have any thing that stands out that could be wrong other than fdt_skip_update. This is a quite important setting, which must be set to yes when running with modern kernel DTB.
fdt_skip_update=no
I'd suggest:
- Go back a few kernel versions. Keep using an older and older uImage until it can boot.
- Boot with a normal bootargs (no RAID). Alternately with earlyprintk and without. Load to 0x02000000 (instead of 0x02000020 as stock does):
So for each uImage try 2 boots
fatload usb 0:1 0x02000000 uImage stenv fdt_skip_update yes setenv bootargs 'root=/dev/sda1 console=ttyS0,115200' bootm 0x02000000and
fatload usb 0:1 0x02000000 uImage stenv fdt_skip_update yes setenv bootargs 'root=/dev/sda1 console=ttyS0,115200 earlyprintk=serial' bootm 0x02000000
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on WD MyCloud EX2 Ultra March 19, 2021 02:59PM |
Registered: 4 years ago Posts: 43 |
|
Re: Debian on WD MyCloud EX2 Ultra March 19, 2021 03:52PM |
Admin Registered: 14 years ago Posts: 19,422 |
vzhilov,
> I have tried some so far, but don’t get any
> results. I’m thinking to try with the rescue
> kernel that always boots in case of failover.
> Which one is that? How do I get that, like below?
I'm not familiar with that rescue kernel.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I have tried some so far, but don’t get any
> results. I’m thinking to try with the rescue
> kernel that always boots in case of failover.
> Which one is that? How do I get that, like below?
I'm not familiar with that rescue kernel.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on WD MyCloud EX2 Ultra March 24, 2021 04:06AM |
Registered: 4 years ago Posts: 43 |
I mean, since my /dev/mtdblock1 partition is of a problem I still can boot if I dont stop boot process. As I understand it boots from some other default partition:
So I’m trying to understand which one is that boots fine. So I can copy it to flash drive (with dd) and try to boot with that old kernel from flash drive. As we see above this kernel 100% boots fine. If that will not do so from USB then the problem is something else. Then I will stop trying different kernels and will try to look somewhere else.
Enable HD1
Enable HD2
et:
I port I Interface I PHY address
1 egiga0 I RGMII In—Band
1 egigal RGMII In—Band
1 egiga2 I SGMII 0x00
egiga0, egigal, egiga2 [PRIME]
Hit any key to stop autoboot: 0
nand — NAND sub—system
Usage:
nand info — show available NAND devices
nand device [dev] — show or set current device
nand read — addr off partition size
nand write — addr offipartition size
read/write 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
nand read. raw — addr offlpartition [count]
nand write. raw — addr off partition [count]
Use read.raw/write.raw to avoid ECC and access the flash as—is.
nand write.trimffs — addr offipartition size
write 'size' bytes starting at offset 'off' from memory address
'addr', skipping bad blocks and dropping any pages at the end
of eraseblocks that contain only OxFF
nand erase[.spread] [clean] off size — erase 'size' bytes from offset 'off'
With '.spread', erase enough for given file size, otherwise,
'size' includes skipped bad blocks.
nand erase.part [clean] partition — erase entire mtd partition'
nand erase.chip [clean] — erase entire chip'
nand bad — show bad blocks
nand dump[.00b] off — dump page
nand scrub [—y] off size 1 scrub.part partition 1 scrub.chip
really clean NAND erasing bad blocks (UNSAFE)
nand markbad off [...] — mark bad block(s) at offset (UNSAFE)
nand biterr off — make a bit error at offset (UNSAFE)
AND read: device 0 offset 0xa00000, size 0x500000
5242880 bytes read: OK
•# Booting image at 02000020 ...
AND read: device 0 offset 0xc800800, size 0xf00000
15728640 bytes read: OK
•# Booting image at 00a00000
•# Booting kernel from Legacy Image at 00a00000
Image Name: Linux-382
Created: 2015-08-02 3:54:03 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4093292 Bytes = 3.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum OK
•# Loading init Ramdisk from Legacy Image at 00e00000
Image Name: Ramdisk
Created: 2015-10-05 5:02:44 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7010744 Bytes = 6.7 MiB
Load Address: 00e00000
Entry Point: 00e00000
Verifying Checksum OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU Ox0
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Initializing cgroup subsys cpuacct
Linux version 3.10.39 (kman@kmachine) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALI
GN) ) #1 SMP Sun Aug 2 11:53:57 CST 2015 2014T30p5 Build—git3e9fe59
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 385 Development Board
bootconsole [earlycon0] enabled
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 1 pages/cpu @c09d0000 s8320 r8192 d16256 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32737
Kernel command line: root=/dev/ram console=ttyS0,115200 earlyprintk=serial
PID hash table entries: 4096 (order: —1, 16384 bytes)
So I’m trying to understand which one is that boots fine. So I can copy it to flash drive (with dd) and try to boot with that old kernel from flash drive. As we see above this kernel 100% boots fine. If that will not do so from USB then the problem is something else. Then I will stop trying different kernels and will try to look somewhere else.
|
Re: Debian on WD MyCloud EX2 Ultra April 08, 2021 04:15AM |
Registered: 4 years ago Posts: 43 |
|
Re: Debian on WD MyCloud EX2 Ultra April 08, 2021 04:27PM |
Admin Registered: 14 years ago Posts: 19,422 |
vzhilov,
> Just a remark, I don’t have any HDD attached to
> the device, only the flash drive which I use to
> boot the kernel. Can that be a problem?
Of course. There must be a rootfs somewhere on your system to boot into Debian.
The kernel has started to boot:
However, is this the only output you see on serial console and it stopped?
And your bootargs told the kernel to look for the rootfs on RAID, not on USB.
If the only drive plugged in is the USB with rootfs on it, then the root device should be:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Just a remark, I don’t have any HDD attached to
> the device, only the flash drive which I use to
> boot the kernel. Can that be a problem?
Of course. There must be a rootfs somewhere on your system to boot into Debian.
The kernel has started to boot:
Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU Ox0 Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 3.10.39 (kman@kmachine) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALI GN) ) #1 SMP Sun Aug 2 11:53:57 CST 2015 2014T30p5 Build—git3e9fe59 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 385 Development Board bootconsole [earlycon0] enabled Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 1 pages/cpu @c09d0000 s8320 r8192 d16256 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32737 Kernel command line: root=/dev/ram console=ttyS0,115200 earlyprintk=serial PID hash table entries: 4096 (order: —1, 16384 bytes)
However, is this the only output you see on serial console and it stopped?
And your bootargs told the kernel to look for the rootfs on RAID, not on USB.
Kernel command line: root=/dev/ram console=ttyS0,115200 earlyprintk=serial
If the only drive plugged in is the USB with rootfs on it, then the root device should be:
root=/dev/sda1
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on WD MyCloud EX2 Ultra November 24, 2022 01:53PM |
Registered: 2 years ago Posts: 144 |
I think it is my exactly same situation.. totally silence.
Edited 1 time(s). Last edit at 11/24/2022 01:58PM by i5Js.
Marvell>> fatload usb 0:1 0x02000000 boot_mio/uImage reading boot_mio/uImage 3886355 bytes read in 153 ms (24.2 MiB/s) Marvell>> setenv fdt_skip_update yes Marvell>> setenv bootargs root=/dev/sda2 console=ttyS0,115200 earlyprintk=serial Marvell>> bootm 0x02000000 ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: WDMC-Gen2 Created: 2022-11-23 15:00:20 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3886291 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK
Edited 1 time(s). Last edit at 11/24/2022 01:58PM by i5Js.
|
Re: Debian on WD MyCloud EX2 Ultra November 24, 2022 02:39PM |
Registered: 2 years ago Posts: 144 |
Testing with one of your kernels
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> fatload usb 0:1 0x02000000 boot/uimage
reading boot/uimage
5076006 bytes read in 195 ms (24.8 MiB/s)
Marvell>> setenv fdt_skip_update yes
Marvell>> setenv bootargs root=/dev/sda2 console=ttyS0,115200 earlyprintk=serial
Marvell>> bootm 0x02000000
## Booting image at 02000000 ...
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-5.2.9-mvebu-tld-1
Created: 2022-11-24 20:26:21 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5075942 Bytes = 4.8 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
|
Re: Debian on WD MyCloud EX2 Ultra January 18, 2023 04:08AM |
Registered: 2 years ago Posts: 12 |
Hi guys, i had modded my ex2 ultra with the following guide:
https://wd.hides.su/wdnas.el8.website/WDMyCloud-Ex2-Ultra/Debian-linux_4.14.4/_info_EN.txt
My rootfs is currently on my Radi 1 hdd's:
mount /dev/md1 /mnt/root
I am on the kernel used by that guide (4.15 RC6) and i want to update it to at least 5.1.x without loosing my data / configuration.
Can you guys please help me with that?
Thank you so much in advance
Edited 1 time(s). Last edit at 01/18/2023 10:10AM by marcexeu.
https://wd.hides.su/wdnas.el8.website/WDMyCloud-Ex2-Ultra/Debian-linux_4.14.4/_info_EN.txt
My rootfs is currently on my Radi 1 hdd's:
mount /dev/md1 /mnt/root
I am on the kernel used by that guide (4.15 RC6) and i want to update it to at least 5.1.x without loosing my data / configuration.
Can you guys please help me with that?
Thank you so much in advance
Edited 1 time(s). Last edit at 01/18/2023 10:10AM by marcexeu.
|
Re: Debian on WD MyCloud EX2 Ultra January 18, 2023 02:35PM |
Admin Registered: 14 years ago Posts: 19,422 |
marcexeu,
> I am on the kernel used by that guide (4.15 RC6)
> and i want to update it to at least 5.1.x without
> loosing my data / configuration.
Whatever you will decide, you should backup the rootfs before doing anything.
The kernel is recent enough
wget http://fox-exe.ru/WDMyCloud/WDMyCloud-Ex2-Ultra/Debian-linux_4.14.4/debian-stretch-rootfs.tar.xz
that you could potentially upgrade the kernel and also the stretch rootfs to some later Debian version. But the rootfs upgrade will be a massive change.
Debian stretch is too old. Have you upgrade Debian, and to what version?
You will need serial console. The kernel files can be temporarily on USB or tftp, so you can boot it into your RAID rootfs, so you can see that it work. Booting might have problem depending on what Debian version is on your rootfs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I am on the kernel used by that guide (4.15 RC6)
> and i want to update it to at least 5.1.x without
> loosing my data / configuration.
Whatever you will decide, you should backup the rootfs before doing anything.
The kernel is recent enough
wget http://fox-exe.ru/WDMyCloud/WDMyCloud-Ex2-Ultra/Debian-linux_4.14.4/debian-stretch-rootfs.tar.xz
that you could potentially upgrade the kernel and also the stretch rootfs to some later Debian version. But the rootfs upgrade will be a massive change.
Debian stretch is too old. Have you upgrade Debian, and to what version?
You will need serial console. The kernel files can be temporarily on USB or tftp, so you can boot it into your RAID rootfs, so you can see that it work. Booting might have problem depending on what Debian version is on your rootfs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on WD MyCloud EX2 Ultra January 19, 2023 10:36AM |
Registered: 2 years ago Posts: 12 |
I am currently on debian 11 with kernel Linux-4.15.0-rc6 but i do not have a serial cable.
Looks like i need to update uImage and URamdisk in case i want to upgrade kernel to 5.x or superior.
Update it loosing data on roots is ok if necessary (i can reinstall samba, trasmission and openvpn server), i think what i need is uImage and Ramdisk compactible with a newer kernel + to untar the new kernel to my rootfs right?
Looks like i need to update uImage and URamdisk in case i want to upgrade kernel to 5.x or superior.
Update it loosing data on roots is ok if necessary (i can reinstall samba, trasmission and openvpn server), i think what i need is uImage and Ramdisk compactible with a newer kernel + to untar the new kernel to my rootfs right?
|
Re: Debian on WD MyCloud EX2 Ultra January 19, 2023 04:26PM |
Admin Registered: 14 years ago Posts: 19,422 |
> I am currently on debian 11 with kernel
> Linux-4.15.0-rc6
Great! then you could install new kernel linux-5.15.5-mvebu-tld-1-bodhi.tar.bz2 or the latest linux-6.0.7-mvebu-tld-1-bodhi.tar.bz2 But try it out with tftp or USB first.
> but i do not have a serial cable.
That will make quite risky.
>
> Looks like i need to update uImage and URamdisk in
> case i want to upgrade kernel to 5.x or superior.
>
>
> Update it loosing data on roots is ok if necessary
> (i can reinstall samba, trasmission and openvpn
> server), i think what i need is uImage and Ramdisk
> compactible with a newer kernel + to untar the new
> kernel to my rootfs right?
No. You are booting with the kernel stored on flash, and rootfs on RAID. Eventhough the kernel is installed on the rootfs, kernel files need to be copied to NAND like you did before in that installation.
The flashing above is the risky part. If it does not work, then you have to connect serial console to recover (it is painful to do so). So serial console will allow you to boot the new kernel using tftp or USB storage first.
Or one of the users in this working thread can volunteer to flash the new kernel and boot that way so you can be sure it will work.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 01/19/2023 04:26PM by bodhi.
> Linux-4.15.0-rc6
Great! then you could install new kernel linux-5.15.5-mvebu-tld-1-bodhi.tar.bz2 or the latest linux-6.0.7-mvebu-tld-1-bodhi.tar.bz2 But try it out with tftp or USB first.
> but i do not have a serial cable.
That will make quite risky.
>
> Looks like i need to update uImage and URamdisk in
> case i want to upgrade kernel to 5.x or superior.
>
>
> Update it loosing data on roots is ok if necessary
> (i can reinstall samba, trasmission and openvpn
> server), i think what i need is uImage and Ramdisk
> compactible with a newer kernel + to untar the new
> kernel to my rootfs right?
No. You are booting with the kernel stored on flash, and rootfs on RAID. Eventhough the kernel is installed on the rootfs, kernel files need to be copied to NAND like you did before in that installation.
Quote
https://wd.hides.su/wdnas.el8.website/WDMyCloud-Ex2-Ultra/Debian-linux_4.14.4/_info_EN.txt
dd if=/dev/zero of=/dev/mtdblock1
dd if=uImage of=/dev/mtdblock1
dd if=/dev/zero of=/dev/mtdblock2
dd if=uRamdisk of=/dev/mtdblock2
The flashing above is the risky part. If it does not work, then you have to connect serial console to recover (it is painful to do so). So serial console will allow you to boot the new kernel using tftp or USB storage first.
Or one of the users in this working thread can volunteer to flash the new kernel and boot that way so you can be sure it will work.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 01/19/2023 04:26PM by bodhi.
|
Re: Debian on WD MyCloud EX2 Ultra January 20, 2023 02:26AM |
Registered: 2 years ago Posts: 12 |
Thank you, there is a recovery mode from usb on this device for re-flashing the uImage and uRamdisk, so no issues with:
dd if=/dev/zero of=/dev/mtdblock1
dd if=uImage of=/dev/mtdblock1
dd if=/dev/zero of=/dev/mtdblock2
dd if=uRamdisk of=/dev/mtdblock2
If possible i would like to update it to kernel 6.0.7, if i undestood it correclty the process is:
1) Unpack kernel on Rootfs
2) Flash uImage
3) Flash uRamdisk
4) reboot
right?
So now what i need is only the uImage and uRamdisk that workds with 6.0.7, but i do not have a dtd file, and even if i found one, i dont know how to configure it to boot from my sata hdd. Can you please help me on that?
Thank you in advance!
dd if=/dev/zero of=/dev/mtdblock1
dd if=uImage of=/dev/mtdblock1
dd if=/dev/zero of=/dev/mtdblock2
dd if=uRamdisk of=/dev/mtdblock2
If possible i would like to update it to kernel 6.0.7, if i undestood it correclty the process is:
1) Unpack kernel on Rootfs
2) Flash uImage
3) Flash uRamdisk
4) reboot
right?
So now what i need is only the uImage and uRamdisk that workds with 6.0.7, but i do not have a dtd file, and even if i found one, i dont know how to configure it to boot from my sata hdd. Can you please help me on that?
Thank you in advance!
|
Re: Debian on WD MyCloud EX2 Ultra January 20, 2023 03:19PM |
Admin Registered: 14 years ago Posts: 19,422 |
marcexeu,
> 1) Unpack kernel on Rootfs
> 2) Flash uImage
> 3) Flash uRamdisk
> 4) reboot
>
> right?
Incorrect. What the above does is an intermediate step that hopefully will boot the system, but not a full installation.
Here is the full kernel installation in my release thread.
Just run uImage and uInitrd (i.e. uRamdisk) will boot the system into your rootfs (a different rootfs than the kernel is intended for). Most likely it will boot your current rootfs, but it will encounter problem later.
Step 3 above will install the kernel, and populate other parts of the rootfs.
>
> So now what i need is only the uImage and uRamdisk
> that workds with 6.0.7, but i do not have a dtd
> file, and even if i found one,
Step 4 above will append the DTB to uImage for kernel 6.0.7.
> i dont know how to
> configure it to boot from my sata hdd. Can you
> please help me on that?
Once you can boot the kernel, it will find your rootfs on RAID. When you get to that point, I can help. Also you can read this thread to see what other people have done.
========
Note:
The new kernel uImage and uInitrd size are substantially larger than the old kernel. So the flashing must take into account about the difference. And the boot command in u-boot might have to be adjusted to boot the new kernel.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 01/20/2023 03:42PM by bodhi.
> 1) Unpack kernel on Rootfs
> 2) Flash uImage
> 3) Flash uRamdisk
> 4) reboot
>
> right?
Incorrect. What the above does is an intermediate step that hopefully will boot the system, but not a full installation.
Here is the full kernel installation in my release thread.
Quote
Updated 09 Nov 2022:
Kernel 6.0.7-mvebu-tld-1 package has been uploaded.
New/Updated in this release:
- General kernel upgrade.
Latest Linux kernel 6.x general release information can be found at:
LinuxChanges log
Download at Dropbox
linux-6.0.7-mvebu-tld-1-bodhi.tar.bz2
md5:
bfb1d7cf103f501b991e21b9886db4f6
sha256:
dcf50e17352f7d84ab606abdef374ec0d3db1c39b242c6ae7924b7283edc3ead
As always, please check the hash of your download!
There are 6 files in this tarball:
Quote
linux-image-6.0.7-mvebu-tld-1_1.0_armhf.deb
linux-headers-6.0.7-mvebu-tld-1_1.0_armhf.deb
zImage-6.0.7-mvebu-tld-1
config-6.0.7-mvebu-tld-1
linux-dtb-6.0.7-mvebu-tld-1.tar
linux-6.0.7-mvebu-tld-1.patch
Installation
NOTE: the following steps are for a general kernel upgrade. For initial installation, please see "Installation Instruction for specific boxes" in the thread description at the top of this release thread.
1. Backup your current zImage, uImage, and uInitrd. In the /boot directory, these are files for your current kernel (xx.xx.xx is the version number):
uInitrd
uImage
zImage-xx.xx.xx-mvebu-xxx
initrd.img-xx.xx.xx-mvebu-xxx
System.map-xx.xx.xx-mvebu-xxx
vmlinuz-xx.xx.xx-mvebu-xxx
config-xx.xx.xx-mvebu-xxx
dts/
2. Extract the kernel and the DTB files in the archive:
cd /boot
tar -xjf linux-6.0.7-mvebu-tld-1-bodhi.tar.bz2
tar -xf linux-dtb-6.0.7-mvebu-tld-1.tar
3. And install it with dpkg. Remove flash-kernel first to avoid potential problem (if flash-kernel was not installed then you'll see some error output):
cd /boot
apt-get remove flash-kernel
dpkg -i linux-image-6.0.7-mvebu-tld-1_1.0_armhf.deb
4. Create uImage and uInitrd (kernel file initrd.img-6.0.7-mvebu-tld-1 was generated by dpkg in step 3). I am using the Zyxel NAS326 as an example here. Please replace armada-380-zyxel-nas326.dtb below with the appropriate DTB name for your box.
cd /boot
cp -a zImage-6.0.7-mvebu-tld-1 zImage.fdt
cat dts/armada-380-zyxel-nas326.dtb >> zImage.fdt
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.0.7-mvebu-tld-1 -d zImage.fdt uImage
mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-6.0.7-mvebu-tld-1 -d initrd.img-6.0.7-mvebu-tld-1 uInitrd
5. The new uImage and uInitrd files should be created in /boot directory now. You're ready to reboot the system:
sync
sync
sync
shutdown -r now
Just run uImage and uInitrd (i.e. uRamdisk) will boot the system into your rootfs (a different rootfs than the kernel is intended for). Most likely it will boot your current rootfs, but it will encounter problem later.
Step 3 above will install the kernel, and populate other parts of the rootfs.
>
> So now what i need is only the uImage and uRamdisk
> that workds with 6.0.7, but i do not have a dtd
> file, and even if i found one,
Step 4 above will append the DTB to uImage for kernel 6.0.7.
> i dont know how to
> configure it to boot from my sata hdd. Can you
> please help me on that?
Once you can boot the kernel, it will find your rootfs on RAID. When you get to that point, I can help. Also you can read this thread to see what other people have done.
========
Note:
The new kernel uImage and uInitrd size are substantially larger than the old kernel. So the flashing must take into account about the difference. And the boot command in u-boot might have to be adjusted to boot the new kernel.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 01/20/2023 03:42PM by bodhi.
