Zyxel NSA325 questions (uboot) April 25, 2020 12:52PM |
Registered: 4 years ago Posts: 2 |
Re: Zyxel NSA325 questions (uboot) April 25, 2020 04:56PM |
Admin Registered: 13 years ago Posts: 19,107 |
Re: Zyxel NSA325 questions (uboot) April 26, 2020 02:38AM |
Registered: 4 years ago Posts: 2 |
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init bootcmd=nand read.e 0x2000000 $(kernel_addr) 0xA00000; bootm 0x2000000 bootdelay=2 baudrate=115200 loads_echo=0 ipaddr=10.4.52.165 serverip=10.4.52.7 rootpath=/srv/ubuntu netmask=255.255.255.0 nandEcc=1bit MODEL_ID=AE03 PRODUCT_NAME=NSA-325v2 FEATURE_BIT=00 CONTRY_TYPE=FF VENDOR_NAME=MitraStar Technology Corp. run_diag=yes ethaddr=4C:9E:FF:BF:55:FC stdin=serial stdout=serial stderr=serial console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root) mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes ethprime=egiga0 netbsd_en=no vxworks_en=no bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; lcd0_enable=0 lcd0_params=640x480-16@60 disaMvPnp=no ethmtu=1500 mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no image_multi=yes enaAutoRecovery=yes kernel_addr=0xc80000 pcieTune=no pcieTune1=no ethact=egiga0
arcNumber=4495 baudrate=115200 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=console=ttyS0,115200 device=0:1 devices=usb ide disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-nsa325.dtb ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15
Re: Zyxel NSA325 questions (uboot) April 26, 2020 03:39AM |
Admin Registered: 13 years ago Posts: 19,107 |
Multivan
Re: Zyxel NSA325 questions (uboot) August 25, 2023 04:42AM |
Re: Zyxel NSA325 questions (uboot) August 25, 2023 12:45PM |
Admin Registered: 13 years ago Posts: 19,107 |
Multivan
Re: Zyxel NSA325 questions (uboot) September 05, 2023 07:45AM |
Re: Zyxel NSA325 questions (uboot) September 05, 2023 12:14PM |
Admin Registered: 13 years ago Posts: 19,107 |
Quote
Where did you download this u-boott.kwb (what version is this), stock u-boot or one of my new u-boot releases?
Multivali
Re: Zyxel NSA325 questions (uboot) September 06, 2023 09:01AM |
Re: Zyxel NSA325 questions (uboot) September 06, 2023 02:49PM |
Admin Registered: 13 years ago Posts: 19,107 |
Multivan
Re: Zyxel NSA325 questions (uboot) September 12, 2023 11:49AM |
Re: Zyxel NSA325 questions (uboot) September 12, 2023 12:54PM |
Admin Registered: 13 years ago Posts: 19,107 |
printenv bootAnd post the entire serial console log here (copy/paste everything on the terminal).
Multivan
Re: Zyxel NSA325 questions (uboot) September 13, 2023 01:54AM |
NSA325> printenv baudrate=115200 bootcmd=run setenv bootargs; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000 bootdelay=3 console=console=ttyS0,115200 ethact=egiga0 ethaddr=xx:xx:xx:xx:xx:xx mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x00c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi) stderr=serial stdin=serial stdout=serial Environment size: 349/131068 bytes NSA325> boot ## Error: "setenv" not defined ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=2", size 126 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512 ubi0: VID header offset: 512 (aligned 512), data offset: 2048 ubi0: good PEBs: 1009, bad PEBs: 5, corrupted PEBs: 0 ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1682627295 ubi0: available PEBs: 0, total reserved PEBs: 1009, PEBs reserved for bad PEB handling: 15 Read 0 bytes from volume kernel to 800000 No size specified -> Using max size (2709504) ## Booting kernel from Legacy Image at 00800000 ... Image Name: ARM OpenWrt Linux-5.10.176 Created: 2023-04-27 20:28:15 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2689432 Bytes = 2.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.176 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r20134-5f15225c1e) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 Thu Apr 27 20:28:15 2023 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: ZyXEL NSA325 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttyS0,115200 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 510160K/524288K available (6008K kernel code, 600K rwdata, 928K rodata, 1024K init, 215K bss, 14128K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000038] Switching to timer-based delay loop, resolution 5ns [ 0.000165] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000190] pid_max: default: 32768 minimum: 301 [ 0.000356] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.000378] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001195] CPU: Testing write buffer coherency: ok [ 0.002294] Setting up static identity map for 0x100000 - 0x10003c [ 0.002521] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1 [ 0.002731] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.005706] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.005736] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.005856] pinctrl core: initialized pinctrl subsystem [ 0.007283] NET: Registered protocol family 16 [ 0.007630] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.008554] thermal_sys: Registered thermal governor 'step_wise' [ 0.008649] cpuidle: using governor ladder [ 0.008923] Feroceon L2: Enabling L2 [ 0.008964] Feroceon L2: Cache support initialised. [ 0.017627] No ATAGs? [ 0.059756] SCSI subsystem initialized [ 0.061286] usbcore: registered new interface driver usbfs [ 0.061334] usbcore: registered new interface driver hub [ 0.061378] usbcore: registered new device driver usb [ 0.066379] clocksource: Switched to clocksource orion_clocksource [ 0.067094] NET: Registered protocol family 2 [ 0.067285] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.068060] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.068108] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.068165] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.068218] TCP: Hash tables configured (established 4096 bind 4096) [ 0.068291] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.068316] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.068477] NET: Registered protocol family 1 [ 0.068505] PCI: CLS 0 bytes, default 32 [ 0.072386] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.075619] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.075635] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.076287] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.078433] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.079480] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges: [ 0.079518] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 [ 0.079541] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 0.079556] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 0.079716] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 0.079734] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.079747] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) [ 0.079757] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 0.079766] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 0.079862] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400 [ 0.080943] PCI: bus0: Fast back to back transfers disabled [ 0.080958] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.081081] pci 0000:01:00.0: [1033:0194] type 00 class 0x0c0330 [ 0.081116] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 0.081240] pci 0000:01:00.0: PME# supported from D0 D3hot [ 0.081280] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 0.082214] PCI: bus1: Fast back to back transfers disabled [ 0.082231] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.082387] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff] [ 0.082403] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit] [ 0.082423] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.082435] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 0.082487] pci 0000:00:01.0: enabling device (0140 -> 0142) [ 0.082505] pci 0000:01:00.0: enabling device (0140 -> 0142) [ 0.084305] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.085679] printk: console [ttyS0] disabled [ 0.085763] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 0.683818] printk: console [ttyS0] enabled [ 0.688577] Loading iSCSI transport class v2.0-870. [ 0.697613] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 0.704002] nand: Samsung NAND 128MiB 3,3V 8-bit [ 0.708665] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.716275] Scanning device for bad blocks [ 0.731957] Bad eraseblock 121 at 0x000000f20000 [ 0.744156] Bad eraseblock 201 at 0x000001920000 [ 0.762533] Bad eraseblock 346 at 0x000002b40000 [ 0.794324] Bad eraseblock 632 at 0x000004f00000 [ 0.829536] Bad eraseblock 954 at 0x000007740000 [ 0.840773] 3 fixed-partitions partitions found on MTD device orion_nand [ 0.847510] Creating 3 MTD partitions on "orion_nand": [ 0.852674] 0x000000000000-0x0000000c0000 : "uboot" [ 0.859641] 0x0000000c0000-0x000000140000 : "uboot_env" [ 0.865406] 0x000000140000-0x000008000000 : "ubi" [ 0.882095] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 0.892441] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 28:28:5d:13:f0:f8 [ 0.901430] i2c /dev entries driver [ 0.906144] orion_wdt: Initial timeout 21 sec [ 0.921171] marvell-cesa f1030000.crypto: CESA device successfully registered [ 0.929121] NET: Registered protocol family 10 [ 0.935495] Segment Routing with IPv6 [ 0.939275] NET: Registered protocol family 17 [ 0.943790] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 0.956966] 8021q: 802.1Q VLAN Support v1.8 [ 0.965276] UBI: auto-attach mtd2 [ 0.968652] ubi0: attaching mtd2 [ 1.142334] ubi0: scanning is finished [ 1.157366] ubi0: attached mtd2 (name "ubi", size 126 MiB) [ 1.162887] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes [ 1.169815] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512 [ 1.176558] ubi0: VID header offset: 512 (aligned 512), data offset: 2048 [ 1.183377] ubi0: good PEBs: 1009, bad PEBs: 5, corrupted PEBs: 0 [ 1.189508] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 [ 1.196772] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1682627295 [ 1.205944] ubi0: available PEBs: 0, total reserved PEBs: 1009, PEBs reserved for bad PEB handling: 15 [ 1.215584] ubi0: background thread "ubi_bgt0d" started, PID 468 [ 1.222502] block ubiblock0_1: created from ubi0:1(rootfs) [ 1.228037] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem [ 1.240524] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 1.250851] Freeing unused kernel memory: 1024K [ 1.255827] Run /sbin/init as init process [ 1.533486] init: Console is alive [ 1.537149] init: - watchdog - [ 1.919255] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 2.023251] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.035594] fsl-ehci: Freescale EHCI Host controller driver [ 2.045288] ehci-orion: EHCI orion driver [ 2.049499] orion-ehci f1050000.ehci: EHCI Host Controller [ 2.055042] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 2.062862] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 2.096410] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 2.102988] hub 1-0:1.0: USB hub found [ 2.107292] hub 1-0:1.0: 1 port detected [ 2.115885] ehci-platform: EHCI generic platform driver [ 2.131909] sata_mv f1080000.sata: slots 32 ports 2 [ 2.141429] scsi host0: sata_mv [ 2.145662] scsi host1: sata_mv [ 2.149080] ata1: SATA max UDMA/133 irq 32 [ 2.153210] ata2: SATA max UDMA/133 irq 32 [ 2.396392] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 2.598466] hub 1-1:1.0: USB hub found [ 2.602618] hub 1-1:1.0: 4 ports detected [ 2.656405] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 2.665115] ata1.00: ATA-9: WDC WD30EFRX-68EUZN0, 80.00A80, max UDMA/133 [ 2.671864] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 2.683260] ata1.00: configured for UDMA/133 [ 2.687847] scsi 0:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A80 PQ: 0 ANSI: 5 [ 2.697098] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 2.704894] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 2.711242] sd 0:0:0:0: [sda] Write Protect is off [ 2.716151] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.206401] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 3.215115] ata2.00: ATA-9: WDC WD30EFRX-68EUZN0, 80.00A80, max UDMA/133 [ 3.221860] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 3.231178] ata2.00: configured for UDMA/133 [ 3.235734] scsi 1:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A80 PQ: 0 ANSI: 5 [ 3.244985] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 3.252792] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 3.258939] sd 1:0:0:0: [sdb] Write Protect is off [ 3.263841] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.488639] sda: sda1 sda2 [ 3.492473] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.049098] sdb: sdb1 sdb2 [ 4.052983] sd 1:0:0:0: [sdb] Attached SCSI disk [ 4.061886] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 4.067207] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2 [ 4.074889] xhci_hcd 0000:01:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004 [ 4.084222] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 4.089499] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 [ 4.096947] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed [ 4.108479] hub 2-0:1.0: USB hub found [ 4.112737] hub 2-0:1.0: 2 ports detected [ 4.117282] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.126213] hub 3-0:1.0: USB hub found [ 4.130536] hub 3-0:1.0: 2 ports detected [ 4.140476] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.150500] init: - preinit - [ 4.790459] random: jshn: uninitialized urandom read (4 bytes read) [ 4.879912] random: jshn: uninitialized urandom read (4 bytes read) [ 5.097363] random: jshn: uninitialized urandom read (4 bytes read) [ 5.237642] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled [ 5.247469] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 6.859443] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled [ 6.869285] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9.440818] UBIFS (ubi0:2): Mounting in unauthenticated mode [ 9.472542] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 667 [ 9.505853] UBIFS (ubi0:2): recovery needed [ 9.634917] UBIFS (ubi0:2): recovery completed [ 9.639482] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data" [ 9.647369] UBIFS (ubi0:2): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 9.657339] UBIFS (ubi0:2): FS size: 120637440 bytes (115 MiB, 935 LEBs), journal size 6064128 bytes (5 MiB, 47 LEBs) [ 9.667999] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB) [ 9.674647] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID CE6DD0C1-1FB5-4D73-A2B8-DDBB23A9BFAF, small LPT model [ 9.689042] mount_root: switching to ubifs overlay [ 9.700926] urandom-seed: Seeding with /etc/urandom.seed [ 9.767706] procd: - early - [ 9.770726] procd: - watchdog - [ 10.383035] procd: - watchdog - [ 10.387081] procd: - ubus - [ 10.433123] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.442335] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.449060] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.457929] procd: - init - Please press Enter to activate this console. [ 11.170656] kmodloader: loading kernel modules from /etc/modules.d/* [ 11.234609] rtc-pcf8563 0-0051: registered as rtc0 [ 11.246437] rtc-pcf8563 0-0051: setting system clock to 2023-09-13T06:36:35 UTC (1694586995) [ 11.262652] urngd: v1.0.2 started. [ 11.349965] PPP generic driver version 2.4.2 [ 11.368584] NET: Registered protocol family 24 [ 11.395853] kmodloader: done loading kernel modules from /etc/modules.d/* [ 11.415830] random: crng init done [ 11.419282] random: 28 urandom warning(s) missed due to ratelimiting [ 17.621251] br-lan: port 1(eth0) entered blocking state [ 17.626545] br-lan: port 1(eth0) entered disabled state [ 17.631992] device eth0 entered promiscuous mode [ 20.596176] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control enabled [ 20.630712] br-lan: port 1(eth0) entered blocking state [ 20.635975] br-lan: port 1(eth0) entered forwarding state [ 20.655605] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Re: Zyxel NSA325 questions (uboot) September 13, 2023 08:50AM |
Registered: 8 years ago Posts: 38 |
Multivan
Re: Zyxel NSA325 questions (uboot) September 13, 2023 11:08AM |
Re: Zyxel NSA325 questions (uboot) September 13, 2023 11:53AM |
Registered: 8 years ago Posts: 38 |
Re: Zyxel NSA325 questions (uboot) September 13, 2023 02:00PM |
Admin Registered: 13 years ago Posts: 19,107 |