Re: RN10400 October 11, 2020 10:37AM |
Registered: 4 months ago Posts: 26 |
Re: RN10400 November 15, 2020 01:18AM |
Registered: 4 months ago Posts: 26 |
Re: RN10400 November 15, 2020 04:32PM |
Admin Registered: 9 years ago Posts: 14,850 |
apt-get update apt-get install picocom apt-get install minicom
Re: RN10400 November 21, 2020 04:14AM |
Registered: 4 months ago Posts: 26 |
Re: RN10400 November 21, 2020 04:17AM |
Registered: 3 years ago Posts: 93 |
Re: RN10400 November 21, 2020 04:21AM |
Registered: 4 months ago Posts: 26 |
Re: RN10400 November 21, 2020 04:30AM |
Registered: 4 months ago Posts: 26 |
Re: RN10400 November 21, 2020 04:44AM |
Registered: 3 years ago Posts: 93 |
Re: RN10400 November 21, 2020 04:33PM |
Admin Registered: 9 years ago Posts: 14,850 |
Re: RN10400 December 28, 2020 11:11AM |
Registered: 4 months ago Posts: 26 |
Re: RN10400 December 28, 2020 12:21PM |
Registered: 2 years ago Posts: 161 |
Re: RN10400 December 28, 2020 12:58PM |
Registered: 4 months ago Posts: 26 |
Re: RN10400 December 28, 2020 02:48PM |
Registered: 4 months ago Posts: 26 |
BootROM 1.08 Booting from NAND flash General initialization - Version: 1.0.0 High speed PHY - Version: 2.1.4 (COM-PHY-V20) Update PEX Device ID 0x6710 High speed PHY - Ended Successfully 0001 DDR3 Training Sequence - Ver 5.7.1 DDR3 Training Sequence - Run without PBS. DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1 06/23/2015 ReadyNAS-104 V2.0 Board: DB-88F6710-BP SoC: MV6710 A1 CPU: Marvell PJ4B v7 UP (Rev 1) LE CPU @ 1200 [MHz] L2 @ 600 [MHz] TClock @ 200 [MHz] DDR @ 600 [MHz] DDR 16Bit Width, FastPath Memory Access DRAM: 512 MiB Map: Code: 0x1feef000:0x1ff9f514 BSS: 0x1ffef8a0 Stack: 0x1f9eeef8 Heap: 0x1f9ef000:0x1feef000 NAND: (ID 0xf12c) 128 MiB MMC: MRVL_MMC: 0 Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 Initialize and scan all PCI interfaces PEX unit.port(active IF[-first bus]): ------------------------------------------ PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0 PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0 FPU not initialized USB 0: Host Mode USB 1: Host Mode Shutting down unused interfaces: SDIO AUDIO TDM Modules/Interfaces Detected: RGMII0 Phy RGMII1 Phy PEX0 (Lane 0) PEX1 (Lane 1) SATA0 (Lane 2) SATA1 (Lane 3) Net: egiga0, egiga1 [PRIME] Power On! FDT loaded successfully Hit any key to stop autoboot: 0 (Re)start USB... USB: Active port: 0 Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Invalid boot device ** ** Invalid boot device ** NAND read: device 0 offset 0xd4000, size 0x6000 24576 bytes read: OK Wrong Image Format for bootm command ERROR: can't get kernel image! Marvell>>
Re: RN10400 December 28, 2020 04:08PM |
Admin Registered: 9 years ago Posts: 14,850 |
Quote
root@Debian:~# picocom --b 115200 --f n --p n --d 8 /dev/ttyUSB0
Quote
scanning bus for storage devices... 0 Storage Device(s) found
Quote
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Quote
Hit any key to stop autoboot: 0
printenvPlease post the serial console log up until this point.
Re: RN10400 December 29, 2020 01:01AM |
Registered: 4 months ago Posts: 26 |
Re: RN10400 December 29, 2020 06:49PM |
Registered: 4 months ago Posts: 26 |
Re: RN10400 December 30, 2020 02:17AM |
Admin Registered: 9 years ago Posts: 14,850 |
This text is inside code tags
Re: RN10400 December 30, 2020 02:23PM |
Registered: 4 months ago Posts: 26 |
Ps.: i did that with the output from the RN10400 yesterday, i edit the the message and cut out the output from the RN10400 then i push the formatted code bottom and copy the output in there.