Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 07, 2015 04:08AM |
Registered: 9 years ago Posts: 50 |
... [ 4.865759] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1 [ 4.872168] nand: Eon NAND 128MiB 3,3V 8-bit [ 4.876451] nand: 128MiB, SLC, page size: 2048, OOB size: 64 [ 4.882145] Scanning device for bad blocks [ 4.891585] Bad eraseblock 100 at 0x000000c80000 [ 4.901493] Bad eraseblock 200 at 0x000001900000 [ 4.954432] Creating 9 MTD partitions on "orion_nand": ...
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 07, 2015 05:03AM |
Admin Registered: 13 years ago Posts: 19,006 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 07, 2015 09:41AM |
Registered: 9 years ago Posts: 50 |
U-Boot 2013.10-tld-1 (Aug 29 2014 - 22:07:26) ZyXEL NSA325 2-Bay Power Media Server SoC: Kirkwood 88F6282_?? DRAM: 512 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA325>
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 08, 2015 04:57AM |
Admin Registered: 13 years ago Posts: 19,006 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 08, 2015 05:32AM |
Registered: 9 years ago Posts: 22 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 08, 2015 12:12PM |
Registered: 9 years ago Posts: 50 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 08, 2015 12:37PM |
Admin Registered: 13 years ago Posts: 19,006 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 10, 2015 08:14AM |
Registered: 10 years ago Posts: 94 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 10, 2015 10:58AM |
Admin Registered: 13 years ago Posts: 19,006 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 24, 2015 10:56PM |
Registered: 14 years ago Posts: 89 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 24, 2015 11:31PM |
Admin Registered: 13 years ago Posts: 19,006 |
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi rescue_installed=1 pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi bootcmd=usb start; run force_rescue_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; reset
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 25, 2015 10:57AM |
Registered: 14 years ago Posts: 89 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 25, 2015 11:51AM |
Admin Registered: 13 years ago Posts: 19,006 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 26, 2015 06:23AM |
Registered: 10 years ago Posts: 26 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 26, 2015 06:44AM |
Admin Registered: 13 years ago Posts: 19,006 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 26, 2015 11:20AM |
Registered: 10 years ago Posts: 26 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 27, 2015 08:19AM |
Registered: 14 years ago Posts: 89 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 27, 2015 09:26AM |
Admin Registered: 13 years ago Posts: 19,006 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 27, 2015 10:42AM |
Registered: 14 years ago Posts: 89 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 27, 2015 11:46AM |
Admin Registered: 13 years ago Posts: 19,006 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 27, 2015 09:45PM |
Registered: 9 years ago Posts: 5 |
Reset IDE: ide_preinit failed
IDE device 0: device type unknown IDE device 1: device type unknown
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 27, 2015 09:53PM |
Registered: 14 years ago Posts: 89 |
root@LinuxA:/# fw_printenv mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) baudrate=115200 bootcmd=run bootcmd_uenv; run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 if_netconsole=ping $serverip led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand partition=nand0,2 preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi uenv_import=echo importing envs ...; env import -t 0x810000 uenv_load=usb start; mmc rescan; ide reset; setenv uenv_loaded 0; for devtype in usb mmc ide; do for disknum in 0; do run uenv_read_disk; done; done uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi arcNumber=2998 ethaddr=00:10:75:1A:3D:0C serverip=192.168.2.106 ipaddr=192.168.2.108
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 27, 2015 11:33PM |
Admin Registered: 13 years ago Posts: 19,006 |
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi rescue_installed=1 pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
bootcmd=run bootcmd_uenv; run force_rescue_bootcmd; run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; run rescue_bootcmd; reset
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 27, 2015 11:37PM |
Admin Registered: 13 years ago Posts: 19,006 |
Reset IDE: ide_preinit failed
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 28, 2015 06:29AM |
Registered: 9 years ago Posts: 5 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 28, 2015 07:59AM |
Admin Registered: 13 years ago Posts: 19,006 |
Quote
But as I said it does not even power on. Also, it's a 3.5 inch drive.
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 28, 2015 03:32PM |
Registered: 9 years ago Posts: 5 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 28, 2015 04:01PM |
Admin Registered: 13 years ago Posts: 19,006 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 28, 2015 06:28PM |
Registered: 9 years ago Posts: 5 |
Re: 2014.07 U-Boot for FDT and Non-FDT Kernel - GoFlexNet, GoFlexHome, PogoE02, Dockstar, iConnect, NetgearStora, PogoV4/Mobile, Sheevaplug January 29, 2015 02:12AM |
Admin Registered: 13 years ago Posts: 19,006 |