In UART boot the default MAC Address is automatically set.

I have created a uEnv.txt file for setting the right one but I get:

Warning: egiga0 MAC addresses don't match:
Address in SROM is         ec:43:f6:40:84:91
Address in environment is  xx:xx:xx:xx:xx:xx

How can I fix this in UART boot ?

>

> Warning: egiga0 MAC addresses don't match:
> Address in SROM is         ec:43:f6:40:84:91
> Address in environment is  xx:xx:xx:xx:xx:xx
>

Try setting it at u-boot prompt

setenv ethaddr xx:xx:xx:xx:xx:xx

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi Wrote:
-------------------------------------------------------
> >

> > Warning: egiga0 MAC addresses don't match:
> > Address in SROM is         ec:43:f6:40:84:91
> > Address in environment is  xx:xx:xx:xx:xx:xx
> >

>
> Try setting it at u-boot prompt
>
>

> setenv ethaddr xx:xx:xx:xx:xx:xx
>

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:42:03 -0700)
ZyXEL NSA325 2-Bay Power Media Server

SoC:   Kirkwood 88F6282_A1
DRAM:  512 MiB
WARNING: Caches not enabled
NAND:  128 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   egiga0
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot:  0
NSA325> setenv ethaddr xx:xx:xx:xx:xx:xx

Warning: egiga0 MAC addresses don't match:
Address in SROM is         xx:xx:xx:xx:xx:xx
Address in environment is  52:3b:20:9c:11:51

The same behaviour.

> Warning: egiga0 MAC addresses don't match:
> Address in SROM is xx:xx:xx:xx:xx:xx
> Address in environment is 52:3b:20:9c:11:51
> [/code]
>
> The same behaviour.

OK. I was hoping it would behave differently. Apparently not.

You will have to either set it explicitly in /etc/network/interfaces in Debian. Or flash the new u-boot, and then set it with setenv (in u-boot) or fw_setenv (in Debian).

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Thanks bodhi.

How shoul it like interfeces ?

Right now I have:

auto lo eth0
iface lo inet loopback
iface eth0 inet dhcp
    hwaddress ether xx:xx:xx:xx:xx:xx

This does not work and reports the same error as before.



Edited 1 time(s). Last edit at 04/10/2022 11:54AM by miazza.

auto lo eth0
iface lo inet loopback
iface eth0 inet dhcp
    hwaddress ether xx:xx:xx:xx:xx:xx

When you have the MAC address in this /etc/network/interfaces, Debian will reset the MAC address while the system boot. So after booting with kwboot into Debian

ifconfig -a

So you should see the MAC address actually being used in the output.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

It seems that the MAC is correct now:

ifconfig -a
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.1.104  netmask 255.255.255.0  broadcast 192.168.1.255
        inet6 fe80::ee43:f6ff:fe40:8491  prefixlen 64  scopeid 0x20<link>
        ether ec:xx:xx:xx:xx:xx  txqueuelen 1000  (Ethernet)
        RX packets 298  bytes 33624 (32.8 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 107  bytes 13369 (13.0 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 35

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 20  bytes 3229 (3.1 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 20  bytes 3229 (3.1 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

The Router is now reading the right MAC.
Thanks



Edited 1 time(s). Last edit at 04/11/2022 02:39PM by miazza.