Sylvania model synet7wid

so i came across this little netbook Sylvania model synet7wid with a VIA wm8505 chip, it shows the SYLVANIA logo on
the screen with Loading OS Image ... then after a few about 10 seconds it says loading device drivers ...
with a bar like the windows xp loading screen. it was supposed to have windows ce 6 and will not go any farther.
okay, so i took it apart and hooked a uart dongle for a com port interface to a pc and this is what i get...

[2024-06-17 18:58:54.122] U-Boot 1.1.4 (Aug 11 2010 - 18:28:15)
[2024-06-17 18:58:54.124] WonderMedia Technologies, Inc.
[2024-06-17 18:58:54.125] WMT U-Boot Version : 0.12.01.00.27
[2024-06-17 18:58:54.128] U-Boot code: 03F80000 -> 03FBA184  BSS: -> 04007DA0
[2024-06-17 18:58:54.133] RAM Configuration:
[2024-06-17 18:58:54.133] Bank #0: 00000000 128 MB
[2024-06-17 18:58:54.136] boot from spi flash.
[2024-06-17 18:58:54.139] flash:
[2024-06-17 18:58:54.139]      Bank1: FFF80000 -- FFFFFFFF
[2024-06-17 18:58:54.142]      Bank2: FF780000 -- FFF7FFFF
[2024-06-17 18:58:54.144] Flash:  8.5 MB
[2024-06-17 18:58:54.174] vibra start !
[2024-06-17 18:58:54.174]   reg op: 0xD811005C | 0x8
[2024-06-17 18:58:54.176]   reg op: 0xD8110084 | 0x8
[2024-06-17 18:58:54.179]   reg op: 0xD81100AC | 0x8
[2024-06-17 18:58:54.191] vibra time: 200 mesc
[2024-06-17 18:58:54.399] vibra stop !
[2024-06-17 18:58:54.399]   reg op: 0xD81100AC & 0xFFFFFFF7
[2024-06-17 18:58:54.619] In:    serial
[2024-06-17 18:58:54.619] Out:   serial
[2024-06-17 18:58:54.619] Err:   serial
[2024-06-17 18:58:54.714] bootcmd="nand readblob 3C00000 3E00000;logo show"
[2024-06-17 18:58:54.716] maddr = 0x3c00000, naddr = 0x3e00000
[2024-06-17 18:58:54.717] 
[2024-06-17 18:58:54.717] <1> Read header
[2024-06-17 18:58:54.722] find NAND Flash SAMSUNG_K9GAG08U0D
[2024-06-17 18:58:54.726] nfc 0x1324 , divisor b
[2024-06-17 18:58:54.726] block4095 tag=74624230  version =1
[2024-06-17 18:58:54.731] block4094 tag=62743142  version =1
[2024-06-17 18:58:54.735] Un-know id = 0x0
[2024-06-17 18:58:54.735] Read finsih
[2024-06-17 18:58:54.738] Header is 0x00119436 0x80101000
[2024-06-17 18:58:54.741] 
[2024-06-17 18:58:54.741] <2> Read Data
[2024-06-17 18:58:54.744] error happen at 0x3c03ff8 ( 0 ) data area  byte387 , bit4 
[2024-06-17 18:58:54.746] org ( 0x3c0417b ) 0x10 =>  0x0
[2024-06-17 18:58:54.749] error happen at 0x3c04ff8 ( 4 ) data area  byte452 , bit0 
[2024-06-17 18:58:54.755] org ( 0x3c059bc ) 0x1 =>  0x0
[2024-06-17 18:58:54.759] error happen at 0x3c08ff8 ( 2 ) data area  byte291 , bit1 
[2024-06-17 18:58:54.765] org ( 0x3c0951b ) 0x2 =>  0x0
[2024-06-17 18:58:54.767] error happen at 0x3c08ff8 ( 4 ) data area  byte67 , bit2 
[2024-06-17 18:58:54.773] org ( 0x3c0983b ) 0x4 =>  0x0
[2024-06-17 18:58:54.777] error happen at 0x3c0cff8 ( 2 ) data area  byte359 , bit5 
[2024-06-17 18:58:54.782] org ( 0x3c0d55f ) 0x20 =>  0x0
[2024-06-17 18:58:54.786] error happen at 0x3c10ff8 ( 0 ) data area  byte397 , bit6 
[2024-06-17 18:58:54.791] org ( 0x3c11185 ) 0x40 =>  0x0
[2024-06-17 18:58:54.794] error happen at 0x3c10ff8 ( 1 ) data area  byte361 , bit3 
[2024-06-17 18:58:54.801] org ( 0x3c11361 ) 0x8 =>  0x0
[2024-06-17 18:58:54.801] error happen at 0x3c10ff8 ( 3 ) data area  byte333 , bit3 
[2024-06-17 18:58:54.806] org ( 0x3c11745 ) 0x8 =>  0x0
[2024-06-17 18:58:54.810] error happen at 0x3c13ff8 ( 6 ) data area  byte219 , bit5 
[2024-06-17 18:58:54.815] org ( 0x3c14cd3 ) 0x20 =>  0x0
[2024-06-17 18:58:54.818] error happen at 0x3c14ff8 ( 1 ) data area  byte493 , bit6 
[2024-06-17 18:58:54.824] org ( 0x3c153e5 ) 0xac =>  0xec
[2024-06-17 18:58:54.826] error happen at 0x3c14ff8 ( 3 ) data area  byte113 , bit3 
[2024-06-17 18:58:54.833] org ( 0x3c15669 ) 0x8 =>  0x0
[2024-06-17 18:58:54.834]  byte487 , bit2 
[2024-06-17 18:58:54.839] org ( 0x3c157df ) 0x4 =>  0x0

....................... 

[2024-06-17 18:58:55.958] org ( 0x3d110fa ) 0x20 =>  0x0
[2024-06-17 18:58:55.962] error happen at 0x3d10ff8 ( 5 ) data area  byte304 , bit2 
[2024-06-17 18:58:55.967] org ( 0x3d11b28 ) 0x4 =>  0x0
[2024-06-17 18:58:55.971] error happen at 0x3d17ff8 ( 0 ) data area  byte520 , bit0 
[2024-06-17 18:58:55.974] org ( 0x3d18200 ) 0xb4 =>  0xb5
[2024-06-17 18:58:55.978] error happen at 0x3d17ff8 ( 6 ) data area  byte239 , bit3 
[2024-06-17 18:58:55.983] org ( 0x3d18ce7 ) 0x8 =>  0x0
[2024-06-17 18:58:55.985] error happen at 0x3d17ff8 ( 7 ) data area  byte2 , bit0 
[2024-06-17 18:58:55.991] org ( 0x3d18dfa ) 0x1 =>  0x0
[2024-06-17 18:58:55.994] error happen at 0x3d18ff8 ( 1 ) data area  byte98 , bit3 
[2024-06-17 18:58:55.998] org ( 0x3d1925a ) 0x8 =>  0x0
[2024-06-17 18:58:56.002] error happen at 0x3d18ff8 ( 6 ) data area  byte233 , bit4 
[2024-06-17 18:58:56.007] org ( 0x3d19ce1 ) 0x92 =>  0x82
[2024-06-17 18:58:56.010] Read finsih
[2024-06-17 18:58:56.010] show logo .....
[2024-06-17 18:58:56.014] LCD param (setting): 1,30000,8,800,480,48,40,40,3,29,13,d8110508|10,d8110504|10,d8110500|10
[2024-06-17 18:58:56.023] PWM param (setting): 0,25,100,90,98,58,8,0,27
[2024-06-17 18:58:56.035] LCD FrameBuffer = 0x07600000, BMP Address = 0x03C00000
[2024-06-17 18:58:56.271] Loading BMP ..... 
[2024-06-17 18:58:56.271] colorBits = 24
[2024-06-17 18:58:56.274] logo_width = 800, logo_height= 480
[2024-06-17 18:58:56.277] lcd_width= 800, lcd_height = 480
[2024-06-17 18:58:56.487] ok
[2024-06-17 18:58:56.491] Execute register operation for LCD:
[2024-06-17 18:58:56.494]   reg op: 0xD8110508 | 0x10
[2024-06-17 18:58:56.497]   reg op: 0xD8110504 | 0x10
[2024-06-17 18:58:56.497]   reg op: 0xD8110500 | 0x10
[2024-06-17 18:58:56.503] PWM0 input freq = 47916666 Hz, output freq = 19166 Hz
[2024-06-17 18:58:56.506] PWM0 register setting: scalar = 24, period = 99, duty = 89
[2024-06-17 18:58:56.512] REG32_VAL(0xd8000440) = 0x08080800
[2024-06-17 18:58:56.515] memory size: 128MB
[2024-06-17 18:58:56.520] ### main_loop entered: bootdelay=1
[2024-06-17 18:58:56.525] 
[2024-06-17 18:58:56.525] Execute register operation:
[2024-06-17 18:58:56.527]   reg op: 0xD8110064 | 0xC
[2024-06-17 18:58:56.527]   reg op: 0xD811008C | 0xC
[2024-06-17 18:58:56.530]   reg op: 0xD81100B4 & 0xFFFFFFFB
[2024-06-17 18:58:56.532]   reg op: 0xD81100B4 | 0x8
[2024-06-17 18:58:56.536]   reg op: 0xD8130054 | 0x1
[2024-06-17 18:58:56.542] ### main_loop: bootcmd="nand readblob 100000 0;go 100000"
[2024-06-17 18:58:56.545] Hit Enter key to stop autoboot:  1  0 
[2024-06-17 18:58:56.550] WMT # oot
[2024-06-17 19:02:25.373] Unknown command 'oot' - try 'help'
[2024-06-17 19:02:25.375] WMT # bot
[2024-06-17 19:02:27.685] Unknown command 'bot' - try 'help'
[2024-06-17 19:02:27.688] WMT # boot
[2024-06-17 19:02:29.727] maddr = 0x100000, naddr = 0x0
[2024-06-17 19:02:29.727] 
[2024-06-17 19:02:29.730] <1> Read header
[2024-06-17 19:02:29.730] Read finsih
[2024-06-17 19:02:29.730] Header is 0x015d7950 0x80101000
[2024-06-17 19:02:29.735] 
[2024-06-17 19:02:29.735] <2> Read Data
[2024-06-17 19:02:29.737] error happen at 0x103ff8 ( 0 ) data area  byte188 , bit2 
[2024-06-17 19:02:29.740] org ( 0x1040b4 ) 0x85 =>  0x81
[2024-06-17 19:02:29.743] error happen at 0x103ff8 ( 6 ) data area  byte200 , bit2 
[2024-06-17 19:02:29.748] org ( 0x104cc0 ) 0x65 =>  0x61
[2024-06-17 19:02:29.751] error happen at 0x104ff8 ( 3 ) data area  byte365 , bit4 
[2024-06-17 19:02:29.757] org ( 0x105765 ) 0x50 =>  0x40
[2024-06-17 19:02:29.760] error happen at 0x104ff8 ( 5 ) data area  byte369 , bit4 
[2024-06-17 19:02:29.765] org ( 0x105b69 ) 0x10 =>  0x0
[2024-06-17 19:02:29.768] error happen at 0x104ff8 ( 7 ) data area  byte171 , bit1 
[2024-06-17 19:02:29.773] org ( 0x105ea3 ) 0x2 =>  0x0
[2024-06-17 19:02:29.777] error happen at 0x107ff8 ( 2 ) data area  byte35 , bit2 
[2024-06-17 19:02:29.780] org ( 0x10841b ) 0xe6 =>  0xe2
[2024-06-17 19:02:29.783] error happen at 0x108ff8 ( 4 ) data area  byte186 , bit2 
[2024-06-17 19:02:29.789] org ( 0x1098b2 ) 0x86 =>  0x82
[2024-06-17 19:02:29.793] error happen at 0x10cff8 ( 0 ) data area  byte340 , bit7 
[2024-06-17 19:02:29.798] org ( 0x10d14c ) 0x80 =>  0x0
[2024-06-17 19:02:29.801] error happen at 0x10cff8 ( 3 ) data area  byte146 , bit5 
[2024-06-17 19:02:29.806] org ( 0x10d68a ) 0xad =>  0x8d
[2024-06-17 19:02:29.810] error happen at 0x10fff8 ( 0 ) data area  byte40 , bit7 
[2024-06-17 19:02:29.817] org ( 0x110020 ) 0x80 =>  0x0
[2024-06-17 19:02:29.819] error happen at 0x110ff8 ( 0 ) data area  byte176 , bit1 
[2024-06-17 19:02:29.825] org ( 0x1110a8 ) 0x5b =>  0x59
[2024-06-17 19:02:29.829] error happen at 0x117ff8 ( 0 ) data area  byte388 , bit4 
[2024-06-17 19:02:29.833] org ( 0x11817c ) 0x57 =>  0x47
[2024-06-17 19:02:29.835] error happen at 0x118ff8 ( 5 ) data area  byte496 , bit1 
[2024-06-17 19:02:29.841] org ( 0x119be8 ) 0xff =>  0xfd
[2024-06-17 19:02:29.843] error happen at 0x118ff8 ( 6 ) data area  byte468 , bit0 
[2024-06-17 19:02:29.849] org ( 0x119dcc ) 0x1 =>  0x0
[2024-06-17 19:02:29.854] error happen at 0x11cff8 ( 6 ) data area  byte312 , bit1 
[2024-06-17 19:02:29.857] org ( 0x11dd30 ) 0x12 =>  0x10
[2024-06-17 19:02:29.861] error happen at 0x120ff8 ( 2 ) data area  byte129 , bit0 
[2024-06-17 19:02:29.866] org ( 0x121479 ) 0x31 =>  0x30
[2024-06-17 19:02:29.870] error happen at 0x123ff8 ( 0 ) data area  byte110 , bit2 
[2024-06-17 19:02:29.876] org ( 0x124066 ) 0x94 =>  0x90
[2024-06-17 19:02:29.878] error happen at 0x123ff8 ( 4 ) data area  byte213 , bit3 
[2024-06-17 19:02:29.884] org ( 0x1248cd ) 0x8 =>  0x0
[2024-06-17 19:02:29.887] error happen at 0x123ff8 ( 6 ) data area  byte351 , bit4 
[2024-06-17 19:02:29.892] org ( 0x124d57 ) 0xf1 =>  0xe1
[2024-06-17 19:02:29.899] error happen at 0x12fff8 ( 3 ) data area  byte478 , bit3 
......
[2024-06-17 19:02:47.982] error happen at 0x16c3ff8 ( 3 ) data area  byte6 , bit6 
[2024-06-17 19:02:47.988] org ( 0x16c45fe ) 0xe0 =>  0xa0
[2024-06-17 19:02:47.992] error happen at 0x16c8ff8 ( 5 ) data area  byte289 , bit1 
[2024-06-17 19:02:47.995] org ( 0x16c9b19 ) 0x2 =>  0x0
[2024-06-17 19:02:47.999] error happen at 0x16cbff8 ( 5 ) data area  byte368 , bit5 
[2024-06-17 19:02:48.005] org ( 0x16ccb68 ) 0xa0 =>  0x80
[2024-06-17 19:02:48.009] error happen at 0x16cfff8 ( 6 ) data area  byte242 , bit7 
[2024-06-17 19:02:48.014] org ( 0x16d0cea ) 0x80 =>  0x0
[2024-06-17 19:02:48.017] error happen at 0x16d0ff8 ( 6 ) data area  byte476 , bit4 
[2024-06-17 19:02:48.023] org ( 0x16d1dd4 ) 0x10 =>  0x0
[2024-06-17 19:02:48.029] Read finsih
[2024-06-17 19:02:48.029] ## Starting application at 0x00100000 ...
[2024-06-17 19:02:48.055] Windows CE Kernel for ARM (Thumb Enabled) Built on Oct 20 2009 at 18:39:19
[2024-06-17 19:02:48.061] +WMTOEMInit
[2024-06-17 19:02:48.061] [WMSOC 8505] BSP version: 0.1
[2024-06-17 19:02:48.064] NKForceCleanBoot
[2024-06-17 19:02:48.067] -WMTOEMInit
[2024-06-17 19:02:48.067] OEMGetExtensionDRAM: DRAM (128+0)MB
[2024-06-17 19:02:48.212] bEnvConfig=FALSE.
[2024-06-17 19:02:48.212] okey to crc verified, go...
[2024-06-17 19:02:48.219] warning:parse keypad param failed.
[2024-06-17 19:02:48.222] FMD_Init for board: WM8505_GLink7
[2024-06-17 19:02:48.225] OALIoCtlShowBootProgress(0)
[2024-06-17 19:02:48.228] FMD!DumpRegKey> Drivers\BuiltIn\NFlash 
[2024-06-17 19:02:48.233] 		Profile = MSFlash
[2024-06-17 19:02:48.235] 		IClass :
[2024-06-17 19:02:48.235] 			{A4E7EDDA-E575-4252-9D6B-4195D48BB865}
[2024-06-17 19:02:48.241] 		Order = 00000000
[2024-06-17 19:02:48.241] 		FriendlyName = VIA NAND FLASH Driver (System Disk)
[2024-06-17 19:02:48.246] 		Dll = flashmdd.dll
[2024-06-17 19:02:48.249] 		FlashPddDll = wm_flashpdd_600.dll
[2024-06-17 19:02:48.252] 		Prefix = DSK
[2024-06-17 19:02:48.252] 		Flags = 00001000
[2024-06-17 19:02:48.255] FMD_Init: g_hNandMutex = 0x01050003, 0
[2024-06-17 19:02:48.421] FMD:NAND_WAIT_READY: B2R Status not ready!!
[2024-06-17 19:02:48.425] FMD_Init: nand_reset chip 0 OK!
[2024-06-17 19:02:48.428] ReadFlashID
[2024-06-17 19:02:48.428] FMD_Init: Flash ID is ec d5 94 29 34
[2024-06-17 19:02:48.434] initChipInfo Product ID=SAMSUNG_NF_K9GAG08U0D 
[2024-06-17 19:02:48.437] PLLB_clock Clock=575 MHz
[2024-06-17 19:02:48.439] Clock=00000007 r/w cycle=00002424
[2024-06-17 19:02:48.442] INFO: INT0: Mapped DMAIrq 0x1d to SysDMAIntr 0x10.
[2024-06-17 19:02:48.448] FMD_Init: hevDMAInterrupt = 0x01060003, 0
[2024-06-17 19:02:48.451] ReadBBTSectorBCH:Spare ECC error: startSectorAddr=0x0007ff80                                       
[2024-06-17 19:02:48.459] (sector offset in chip is 0x0007ff80),                                     
[2024-06-17 19:02:48.464] BCH Error count 0x0000000f
[2024-06-17 19:02:48.467] IsBadBlockTBLExisted(block 0x00000fff):Read sector:  0x0007ff80 Failed
[2024-06-17 19:02:48.475] FMD:Scan_NandFlash:  chip 0x00000000 BLOCK 0x00000fff scan fail
[2024-06-17 19:02:48.481] IsBadBlockTBLExisted(block 0x00000ffe):Linux Mirror BBT found:  1tbB
[2024-06-17 19:02:48.487] FMD:Scan_NandFlash: Found Wince TBL pattern=31746242
[2024-06-17 19:02:48.490] FMD:Scan_NandFlash:  chip 0x00000000 BLOCK 0x00000ffd scan fail
[2024-06-17 19:02:48.495] FMD:Scan_NandFlash:  chip 0x00000000 BLOCK 0x00000ffc scan fail
[2024-06-17 19:02:48.504] LoadNandFlashTBL: Use TBL1
[2024-06-17 19:02:48.504] GetBadBlockNum: block 0xb63 in chip 0 is bad block
[2024-06-17 19:02:48.509] GetBadBlockNum: block 0xc72 in chip 0 is bad block
[2024-06-17 19:02:48.515] LoadNandFlashTBL: Bad Block Num=2
[2024-06-17 19:02:48.520] FMD_Init: (Left ~ Right) / Total = (64MB ~ 256MB) / 2048MB !
[2024-06-17 19:02:48.523] FMD_Init done: System Disk.
[2024-06-17 19:02:48.526] FMD_GetInfo
[2024-06-17 19:02:48.529] FMD_GetInfo
[2024-06-17 19:02:48.751] BCH_ReadSector:Spare ECC  error: startSectorAddr=0x00006990                                (sector offset in chip is 0x00006990), NFECC_STATUS2_REG value 0x00000801, ERR_POS_REG1 0x102000e1,                                ERR_POS_REG2 0x00000b51
[2024-06-17 19:02:48.782] BCH_ReadSector:Spare ECC  error: startSectorAddr=0x0000cc18                                (sector offset in chip is 0x0000cc18), NFECC_STATUS2_REG value 0x00000801, ERR_POS_REG1 0x1020001c,                                ERR_POS_REG2 0x00000b51
[2024-06-17 19:02:48.825] BCH_ReadSector:Data ECC  error: startSectorAddr=0x0000ea80                                     (sector offset in chip is 0x0000ea80),                                      NFECC_STATUS2_REG value 0x00000101, ERR_POS_REG1 0x10200e19,ERR_POS_REG2 0x00000b51
[2024-06-17 19:02:48.847] BCH_ReadSector:Data ECC  error: startSectorAddr=0x0000ea80                                     (sector offset in chip is 0x0000ea80),                                      NFECC_STATUS2_REG value 0x00000301, ERR_POS_REG1 0x10200733,ERR_POS_REG2 0x00000b51
[2024-06-17 19:02:48.869] BCH_ReadSector:Data ECC  error: startSectorAddr=0x0000ea80                                     (sector offset in chip is 0x0000ea80),                                      NFECC_STATUS2_REG value 0x00000501, ERR_POS_REG1 0x10200230,ERR_POS_REG2 0x00000b51
[2024-06-17 19:02:48.891] BCH_ReadSector:Data ECC  error: startSectorAddr=0x0000ea80                                     
.....
[2024-06-17 19:03:34.033] BCH_ReadSector:Data ECC  error: startSectorAddr=0x00009409                                     (sector offset in chip is 0x00009409),                                      NFECC_STATUS2_REG value 0x00000701, ERR_POS_REG1 0x0e9503a8,ERR_POS_REG2 0x00001055
[2024-06-17 19:03:34.062] BCH_ReadSector:Data ECC  error: startSectorAddr=0x00009410                                     (sector offset in chip is 0x00009410),                                      NFECC_STATUS2_REG value 0x00000201, ERR_POS_REG1 0x0e950ee5,ERR_POS_REG2 0x00001055
[2024-06-17 19:03:34.087] BCH_ReadSector:Data ECC  error: startSectorAddr=0x00009411                                     (sector offset in chip is 0x00009411),                                      NFECC_STATUS2_REG value 0x00000101, ERR_POS_REG1 0x0e950fde,ERR_POS_REG2 0x00001055
[2024-06-17 19:03:34.122] BCH_ReadSector:Data ECC  error: startSectorAddr=0x00009418                                     (sector offset in chip is 0x00009418),                                      NFECC_STATUS2_REG value 0x00000401, ERR_POS_REG1 0x0e951010,ERR_POS_REG2 0x00001055
[2024-06-17 19:03:34.144] BCH_ReadSector:Data ECC parity error: startSectorAddr=0x00009418                                             (sector offset in chip is 0x00009418),                                              NFECC_STATUS2_REG value 0x00000401, ERR_POS_REG1 0x0e951010,ERR_POS_REG2 0x00001055
[2024-06-17 19:03:34.172] BCH_ReadSector:Data ECC  error: startSectorAddr=0x0000941c                                     (sector offset in chip is 0x0000941c),

---------------------------------------------------------------------------------------------------------------------------------

it just sits there with the little 3 little blue boxes moving like xp does at bootup and the log freezes.
here is some info from the stopping of the uboot

WonderMedia Technologies, Inc.
W-Load Version : 0.19.00.01
ethaddr............found


U-Boot 1.1.4 (Aug 11 2010 - 18:28:15)
WonderMedia Technologies, Inc.
WMT U-Boot Version : 0.12.01.00.27
U-Boot code: 03F80000 -> 03FBA184  BSS: -> 04007DA0
RAM Configuration:
Bank #0: 00000000 128 MB
boot from spi flash.
flash:
     Bank1: FFF80000 -- FFFFFFFF
     Bank2: FF780000 -- FFF7FFFF
Flash:  8.5 MB
vibra start !
  reg op: 0xD811005C | 0x8
  reg op: 0xD8110084 | 0x8
  reg op: 0xD81100AC | 0x8
vibra time: 200 mesc
vibra stop !
  reg op: 0xD81100AC & 0xFFFFFFF7
In:    serial
Out:   serial
Err:   serial
bootcmd="nand readblob 3C00000 3E00000;logo show"
maddr = 0x3c00000, naddr = 0x3e00000

<1> Read header
find NAND Flash SAMSUNG_K9GAG08U0D
nfc 0x1324 , divisor b
block4095 tag=74624230  version =1
block4094 tag=62743142  version =1
Un-know id = 0x0
Read finsih
Header is 0x00119436 0x80101000

<2> Read Data
error happen at 0x3c03ff8 ( 0 ) data area  byte387 , bit4
org ( 0x3c0417b ) 0x10 =>  0x0
error happen at 0x3c04ff8 ( 4 ) data area  byte452 , bit0
org ( 0x3c059bc ) 0x1 =>  0x0
error happen at 0x3c08ff8 ( 2 ) data area  byte291 , bit1
org ( 0x3c0951b ) 0x2 =>  0x0
error happen at 0x3c08ff8 ( 4 ) data area  byte67 , bit2
org ( 0x3c0983b ) 0x4 =>  0x0
........
org ( 0x3d1925a ) 0x8 =>  0x0
error happen at 0x3d18ff8 ( 6 ) data area  byte233 , bit4
org ( 0x3d19ce1 ) 0x92 =>  0x82
Read finsih
show logo .....
LCD param (setting): 1,30000,8,800,480,48,40,40,3,29,13,d8110508|10,d8110504|10,d8110500|10
PWM param (setting): 0,25,100,90,98,58,8,0,27
LCD FrameBuffer = 0x07600000, BMP Address = 0x03C00000
Loading BMP .....
colorBits = 24
logo_width = 800, logo_height= 480
lcd_width= 800, lcd_height = 480
ok
Execute register operation for LCD:
  reg op: 0xD8110508 | 0x10
  reg op: 0xD8110504 | 0x10
  reg op: 0xD8110500 | 0x10
PWM0 input freq = 47916666 Hz, output freq = 19166 Hz
PWM0 register setting: scalar = 24, period = 99, duty = 89
REG32_VAL(0xd8000440) = 0x08080800
memory size: 128MB
### main_loop entered: bootdelay=1

Execute register operation:
  reg op: 0xD8110064 | 0xC
  reg op: 0xD811008C | 0xC
  reg op: 0xD81100B4 & 0xFFFFFFFB
  reg op: 0xD81100B4 | 0x8
  reg op: 0xD8130054 | 0x1
### main_loop: bootcmd="nand readblob 100000 0;go 100000"
Hit Enter key to stop autoboot:  0
WMT #
WMT # ?
shutdown the board
?       - alias for 'help'
autoscr - run script from memory
base    - print or set address offset
bdinfo  - print Board Info structure
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootm   - boot application image from memory
bootp   - boot image via network using BootP/TFTP protocol
cleanlcd - clean LCD screen
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
dhcp    - invoke DHCP client to obtain IP/boot params
diskboot- boot from IDE device
dmacp     - dma memory copy
echo    - echo args to console
erase   - erase FLASH memory
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fatstore - store binary file to a dos filesystem
flinfo  - print FLASH memory information
go      - start application at address 'addr'
help    - print online help
ide     - IDE sub-system
iminfo  - print header information for application image
imls    - list all images found in flash
itest   - return true/false on integer compare
lcdinit - initialize LCD
loadb   - load binary file over serial line (kermit mode)
loads   - load S-Record file over serial line
show    -
loop    - infinite loop on address range
md      - memory display
mii     - MII utility commands
mm      - memory modify (auto-incrementing)
mmcinit - init mmc card
msleep   - delay execution for some time
mtest   - simple RAM test
mw      - memory write (fill)
nand    - NAND sub-system
nfs     - boot image via network using NFS protocol
nm      - memory modify (constant address)
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
randmac - generate a random MAC address and save to "ethaddr" environment variable
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
sdwaitins - wait sd card inserted or removed
sdwaitins 0 -- waiting removed
sdwaitins 1 -- waiting inserted
setenv  - set environment variables
shutdown the board
sleep   - delay execution for some time
textout - show text to the screen
textout x y "str" color
color is 24bit Hex, R[23:16], G[15:8], B[7:0]
for example: textout 0 0 "hello world" FFFFFF
tftpboot- boot image via network using TFTP protocol
tmpt     - execute Mass Production Tool
uploadfile- Transfer the spi flash image to the server.
version - print monitor version
WMT # printenv
baudrate=115200
ipaddr=192.168.1.2
serverip=192.168.1.1
netmask=255.255.255.0
bootfile="uzImage.bin"
loadaddr=0x02000000
serialnum=a2f8d8e6232b7aa93a935f6900349222
sys.flt=947142419
text1=textout 728 458 "V1.7.3" c5c5c5
touchic=true
audioic=wm9715
touchirq=gpio5
kpadid=gcx710v1_17
panelres.x=800
panelres.y=480
bootargs=mem=109M noinitrd root=/dev/mtdblock9 rootfstype=yaffs2 rw console=ttyS0,115200n8 init=/init lcdid=1 androidboot.console=ttyS0
amp_powerup=0xd811005c|0x4,0xd8110084|0x4,0xd81100ac&~0x4
amp_powerdown=0xd811005c|0x4,0xd8110084|0x4,0xd81100ac|0x4
wifi_powerdown=0xd811005c|0x2,0xd8110084|0x2,0xd81100ac&~0x2
wifi_powerup=0xd811005c|0x2,0xd8110084|0x2,0xd81100ac|0x2
basevolt=3300
hibernation_ui=yes
eth_ui=yes
gsensor_axis=0,1,1,-1,2,1
gsensor_int=gpio6
gsensor_ui=yes
motor_ui=yes
vibra_start=0xD811005C|0x8,0xD8110084|0x8,0xD81100AC|0x8
vibra_stop=0xD81100AC&~0x8
vibra_enable=1
restore=no
need_restore_data=yes
orientation_ui=yes
camera_ui=yes
camera_rotate=90
camera_up=5c|0x1,84|0x1,ac|0x1
camera_down=ac&~0x1
pppoe_ui=yes
modem3g_ui=no
enable_hw_scal=no
musicplayer_black_cd=no
restore_byandroid=no
audio.dacpcmvol=15
lcdparam=1,30000,8,800,480,48,40,40,3,29,13,d8110508|10,d8110504|10,d8110500|10
board_name=WM8505_GLink7
TouchIC=0
NoBootProgressBar=0
NoBootInformation=0
battvoltlist=6774,6889,7377,7498,7538,7599,7650,7698,7763,7821,7939
bLowVoltShutdown=1
audio.recordselect=MicIn
audio.gpio=3
audio.ic=VT1613
pwmparam=0,25,100,90,98,58,8,0,27
EthernetIC=1
WIFIGPIO=2
LowVoltConfig=12
gpiostate=1
FakeBattDetect=4
fakeadcpercent=1
ThreshholdCnt=520000
regop=D8110064|C,D811008C|C,D81100B4&~4,D81100B4|8,D8130054|1
ethaddr=00:40:63:2E:0B:9A
wince_system_disk_start_mb=40
wince_system_disk_end_mb=100
wince_flash_disk_start_mb=100
wince_flash_disk_end_mb=ffffffff
flash_safeaddr=2000000
flash_bmpaddr=3E00000
bootdelay=1
SHOW_LOGO=1
LCD_ENABLE=1
LCD_ID=1
BMP_ADR=3C00000
LCDC_FB=7600000
CxScreen=320
CyScreen=1E0
LOGO_STRING=Loading OS Image ...
X_LTEXT=116
Y_LTEXT=166
logocmd=nand readblob 3C00000 3E00000;logo show
bootcmd=nand readblob 100000 0;go 100000
filesize=119436
stdin=serial
stdout=serial
stderr=serial
ver=U-Boot 1.1.4 (Aug 11 2010 - 18:28:15)

Environment size: 2184/65531 bytes
WMT #

---------------------------------------------------------------------

so can this be fixed the way you all do your fancy repairs?

mrc333777,

> so can this be fixed the way you all do your fancy
> repairs?

This is a hard one to do "fancy repairs" :) The NAND flash (which is where the system is) is bad. The saving grace is it's an ARM box and run u-boot. So you would need to find the FW first (backup or installation image). And in u-boot console, you would erase NAND, hoping that all the bad blocks are gathered and put away by the flash controller. And then flash it.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

You could also consider installing a Linux OS on the device as it is supported by the mainline Linux kernel. See https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/boot/dts/vt8500/wm8505-ref.dts which is the device file for Wondermedia WM8505 Netbook.

how would i do all this?

I've had a few of these Sylvania netbooks and a couple have bricked themselves in this same way. I'm guessing cheap NAND and being powered off for a long time was the culprit. I was able to fix them by re-flashing Windows CE with one of the upgrade images Sylvania released many moons ago.

Since I can't seem to find it online anymore, I've reuploaded it here -- https://drive.google.com/file/d/15CuCaBuNny4NJ8yCeipHCzX4mesjXlDV/view

Format an SD card to FAT32, I'd probably make the partition no larger than 2 GB since it can be fussy. Extract the ZIP file onto the card, ensuring the "script" folder is in the base directory. Then insert the card into the netbook and boot. It should automatically erase and re-flash the internal NAND with a clean copy of Windows CE.

I, uh, may also have a Github repo with Debian specifically for these netbooks -- https://github.com/lrussell887/Debian-for-WM8505-Netbooks
Even if the NAND is fried, this runs entirely off of the SD card. Mainline is missing support for the keyboard among other things so this uses a kernel based off linux-vtwm. I only found this post because I ended up Googling `uzImage.bin` while looking over some things lol.

Also this forum seems right up my alley wish I had found it sooner.



Edited 1 time(s). Last edit at 08/14/2024 01:27AM by lrussell887.