Unbrick Stora MS2000

dmitrynino

Unbrick Stora MS2000
February 10, 2025 12:56PM

Registered: 9 months ago
Posts: 3

Hi guys!
I tried to switch to openwrt on my Stora MS2000
I did everything according to the instructions, but at step

tftp 0x0800000 u-boot.kwb
nand erase 0x0 100000
nand write 0x0800000 0x0 0x100000
reset

In the nand write line I wrote nand write 0x0800000 0x0 0x10000 (I skipped 0) and after that, it does not respond, there is nothing in the terminal either

Now when loading u-boot my log looks like this:

  __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: RD-88F6281A LE
  
U-Boot 1.1.4 (Sep  4 2009 - 09:36:11) Marvell version: 3.4.14
  
U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CEE60
  
Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz
  
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size  64MB
DRAM CS[1] base 0x04000000   size  64MB
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
CRC in Flash: ffffffff, Calculated CRC: 619d86db
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
## Error: environment overflow, "stdin" deleted
## Error: environment overflow, "stdout" deleted
## Error: environment overflow, "stderr" deleted
  
CPU : Marvell Feroceon (Rev 1)
## Error: environment overflow, "console" deleted
## Error: environment overflow, "mainlineLinux" deleted
## Error: environment overflow, "CASset" deleted
## Error: environment overflow, "enaMonExt" deleted
## Error: environment overflow, "enaCpuStream" deleted
## Error: environment overflow, "enaWrAllo" deleted
## Error: environment overflow, "pexMode" deleted
## Error: environment overflow, "disL2Cache" deleted
## Error: environment overflow, "setL2CacheWT" deleted
## Error: environment overflow, "disL2Prefetch" deleted
## Error: environment overflow, "enaICPref" deleted
## Error: environment overflow, "enaDCPref" deleted
## Error: environment overflow, "sata_dma_mode" deleted
## Error: environment overflow, "MALLOC_len" deleted
## Error: environment overflow, "ethprime" deleted
## Error: environment overflow, "netbsd_en" deleted
## Error: environment overflow, "vxworks_en" deleted
## Error: environment overflow, "bootargs_root" deleted
## Error: environment overflow, "bootargs_end" deleted
## Error: environment overflow, "image_name" deleted
## Error: environment overflow, "bootcmd" deleted
## Error: environment overflow, "standalone" deleted
## Error: environment overflow, "bootdelay" deleted
## Error: environment overflow, "disaMvPnp" deleted
## Error: environment overflow, "disaMvPnp" deleted
## Error: environment overflow, "ethaddr" deleted
## Error: environment overflow, "ethmtu" deleted
## Error: environment overflow, "eth1addr" deleted
## Error: environment overflow, "eth1mtu" deleted
## Error: environment overflow, "mvPhoneConfig" deleted
## Error: environment overflow, "mvNetConfig" deleted
## Error: environment overflow, "usb0Mode" deleted
## Error: environment overflow, "yuk_ethaddr" deleted
## Error: environment overflow, "nandEcc" deleted
## Error: environment overflow, "hddPowerCtrl" deleted
## Error: environment overflow, "netretry" deleted
## Error: environment overflow, "rcvrip" deleted
## Error: environment overflow, "loadaddr" deleted
## Error: environment overflow, "autoload" deleted
## Error: environment overflow, "enaAutoRecovery" deleted
  
Streaming disabled
Write allocate disabled
  
Module 0 is RGMII
Module 1 is TDM
  
USB 0: device mode
PEX 0: interface detected no Link.
Net:   ## Error: environment overflow, "ethact" deleted
egiga0, egiga1## Error: environment overflow, "ethact" deleted
  
USB:   scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
Aquiring an IP address using DHCP...
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `ethaddr' not set
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `eth1addr' not set
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `ethaddr' not set
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
Failed to retreive an IP address assuming default (<NULL>)!
Starting the Recovery process to retreive the file...
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `eth1addr' not set
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
Failed
Power Button is pressed!
MPP Sel: 00000530, Data IN Enable: 00020058, Data In Polarity: 00000040, Data In: 00000010
Power Button is released!
MAC: 00:01:B8:4A:48:0B, IP: 10.74.72.11
## Error: environment overflow, "ethaddr" deleted
## Error: environment overflow, "ipaddr" deleted
## Error: environment overflow, "serverip" deleted
## Error: environment overflow, "netmask" deleted
## Error: environment overflow, "image_name" deleted
## Error: environment overflow, "console" deleted
## Error: environment overflow, "bootargs_root" deleted
## Error: environment overflow, "rootpath" deleted
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `serverip' not set
## Error: environment overflow, "bootargs" deleted
## Booting image at 00800000 ...
Bad Magic Number

when entering setenv ipaddr I get the error environment overflow ipaddr deleted

I tried to boot from USB, doing it according to these instructions: https://forum.doozan.com/read.php?2,12096
using this u-boot to boot: uboot.2017.07-tld-1.netgear_ms2110.bodhi.tar

after loading I get this log:

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:38:05 -0700)
Netgear Stora MS2110

SoC:   Kirkwood 88F6281_A0
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  256 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   egiga0
PHY reset timed out
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0 
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found

Reset IDE: ide_preinit failed

Partition Map for USB device 0  --   Partition Type: DOS

Part	Start Sector	Num Sectors	UUID		Type
  1	2048      	7829504   	135e42c5-01	83

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **

no IDE devices available
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 692 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
6235659 bytes read in 1155 ms (5.1 MiB/s)
loading uInitrd ...
EHCI timed out on TD - token=0xce008d80
EHCI timed out on TD - token=0xe008d80
5791271 bytes read in 12554 ms (450.2 KiB/s)
loading DTB /boot/dts/kirkwood-netgear_stora_ms2000 ...
** File not found /boot/dts/kirkwood-netgear_stora_ms2000 **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-6.5.7-kirkwood-tld-1
   Created:      2025-02-09  18:02:18 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    6235595 Bytes = 5.9 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-6.5.7-kirkwood-tld-1
   Created:      2023-10-31  22:53:55 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5791207 Bytes = 5.5 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
   Loading Ramdisk to 03a7a000, end 03fffde7 ... OK

Starting kernel ...

[    0.000000][    T0] Booting Linux on physical CPU 0x0
[    0.000000][    T0] Linux version 6.5.7-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 PREEMPT Wed Oct 18 21:14:11 PDT 2023
[    0.000000][    T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000][    T0] CPU: VIVT data cache, VIVT instruction cache
[    0.000000][    T0] OF: fdt: Machine model: NETGEAR MS2000 / MS2110 aka Stora
[    0.000000][    T0] Memory policy: Data cache writeback
[    0.000000][    T0] Zone ranges:
[    0.000000][    T0]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000][    T0] Movable zone start for each node
[    0.000000][    T0] Early memory node ranges
[    0.000000][    T0]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000][    T0] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000][    T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1m(uboot),4m@1m(kernel),251m@5m(rootfs) rw
[    0.000000][    T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000][    T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000][    T0] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000][    T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000][    T0] Memory: 102520K/131072K available (12288K kernel code, 1755K rwdata, 5416K rodata, 1024K init, 301K bss, 28552K reserved, 0K cma-reserved)
[    0.000000][    T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000][    T0] trace event string verifier disabled
[    0.000000][    T0] rcu: Preemptible hierarchical RCU implementation.
[    0.000000][    T0] 	Trampoline variant of Tasks RCU enabled.
[    0.000000][    T0] 	Tracing variant of Tasks RCU enabled.
[    0.000000][    T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000][    T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000][    T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000][    T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000002][    T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.000060][    T0] Switching to timer-based delay loop, resolution 5ns
[    0.000793][    T0] Console: colour dummy device 80x30
[    0.000884][    T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[    0.000922][    T0] CPU: Testing write buffer coherency: ok
[    0.001088][    T0] pid_max: default: 32768 minimum: 301
[    0.011737][    T0] LSM: initializing lsm=capability,integrity
[    0.014622][    T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.014668][    T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.030052][    T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[    0.030592][    T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[    0.031209][    T1] Setting up static identity map for 0x100000 - 0x100058
[    0.031626][    T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2
[    0.032241][    T1] rcu: Hierarchical SRCU implementation.
[    0.032263][    T1] rcu: 	Max phase no-delay instances is 1000.
[    0.035928][    T1] devtmpfs: initialized
[    0.048466][    T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.048523][    T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.052086][    T1] prandom: seed boundary self test passed
[    0.057209][    T1] prandom: 100 self tests passed
[    0.057228][    T1] pinctrl core: initialized pinctrl subsystem
[    0.062837][    T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.064010][    T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.070582][    T1] audit: initializing netlink subsys (disabled)
[    0.073332][    T1] thermal_sys: Registered thermal governor 'step_wise'
[    0.073544][   T19] audit: type=2000 audit(0.070:1): state=initialized audit_enabled=0 res=1
[    0.073609][    T1] cpuidle: using governor ladder
[    0.073711][    T1] cpuidle: using governor menu
[    0.074534][    T1] Feroceon L2: Enabling L2
[    0.074582][    T1] Feroceon L2: Cache support initialised.
[    0.087568][    T1] No ATAGs?
[    0.450081][    T1] raid6: int32x8  gen()    91 MB/s
[    0.790075][    T1] raid6: int32x4  gen()    88 MB/s
[    1.130114][    T1] raid6: int32x2  gen()   113 MB/s
[    1.470075][    T1] raid6: int32x1  gen()    82 MB/s
[    1.470092][    T1] raid6: using algorithm int32x2 gen() 113 MB/s
[    1.810079][    T1] raid6: .... xor() 72 MB/s, rmw enabled
[    1.810096][    T1] raid6: using intx1 recovery algorithm
[    1.812175][    T1] SCSI subsystem initialized
[    1.813150][    T1] usbcore: registered new interface driver usbfs
[    1.813285][    T1] usbcore: registered new interface driver hub
[    1.813407][    T1] usbcore: registered new device driver usb
[    1.813839][    T1] pps_core: LinuxPPS API ver. 1 registered
[    1.813851][    T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.813891][    T1] PTP clock support registered
[    1.817288][    T1] vgaarb: loaded
[    1.830883][    T1] clocksource: Switched to clocksource orion_clocksource
[    1.842499][    T1] VFS: Disk quotas dquot_6.6.0
[    1.843025][    T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.882184][    T1] NET: Registered PF_INET protocol family
[    1.882557][    T1] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    1.884939][    T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    1.885234][    T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    1.885271][    T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    1.885312][    T1] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    1.885353][    T1] TCP: Hash tables configured (established 1024 bind 1024)
[    1.886203][    T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[    1.886499][    T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    1.886542][    T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    1.887609][    T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    1.892053][    T1] RPC: Registered named UNIX socket transport module.
[    1.892071][    T1] RPC: Registered udp transport module.
[    1.892079][    T1] RPC: Registered tcp transport module.
[    1.892086][    T1] RPC: Registered tcp-with-tls transport module.
[    1.892094][    T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.892121][    T1] PCI: CLS 0 bytes, default 32
[    1.901503][   T32] Trying to unpack rootfs image as initramfs...
[    3.086787][   T32] Freeing initrd memory: 5656K
[    4.299770][    T1] Initialise system trusted keyrings
[    4.299902][    T1] Key type blacklist registered
[    4.301842][    T1] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    4.302072][    T1] zbud: loaded
[    4.325155][    T1] NFS: Registering the id_resolver key type
[    4.325220][    T1] Key type id_resolver registered
[    4.325233][    T1] Key type id_legacy registered
[    4.325470][    T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    4.325497][    T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    4.327414][    T1] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    4.328502][    T1] fuse: init (API version 7.38)
[    4.330277][    T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[    4.330732][    T1] orangefs_init: module version upstream loaded
[    4.331262][    T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[    4.585844][    T1] xor: measuring software checksum speed
[    4.596630][    T1]    arm4regs        :   917 MB/sec
[    4.614356][    T1]    8regs           :   556 MB/sec
[    4.626846][    T1]    32regs          :   789 MB/sec
[    4.626858][    T1] xor: using function: arm4regs (917 MB/sec)
[    4.626878][    T1] async_tx: api initialized (async)
[    4.626898][    T1] Key type asymmetric registered
[    4.626908][    T1] Asymmetric key parser 'x509' registered
[    4.690376][    T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    4.691038][    T1] io scheduler bfq registered
[    4.919167][    T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    4.921642][    T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[    4.923272][    T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[    4.924514][    T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[    4.924615][    T1] mvebu-pcie mbus@f1000000:pcie@82000000:      MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[    4.924670][    T1] mvebu-pcie mbus@f1000000:pcie@82000000:      MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[    4.924706][    T1] mvebu-pcie mbus@f1000000:pcie@82000000:       IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[    4.925783][    T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[    4.925809][    T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[    4.925834][    T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[    4.925854][    T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[    4.925872][    T1] pci_bus 0000:00: root bus resource [io  0x1000-0xeffff]
[    4.926013][    T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[    4.928126][    T1] PCI: bus0: Fast back to back transfers disabled
[    4.928161][    T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    4.928562][    T1] PCI: bus1: Fast back to back transfers enabled
[    4.928589][    T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    4.928641][    T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[    4.929949][    T1] mv_xor f1060800.xor: Marvell shared XOR driver
[    4.994098][    T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    4.999860][    T1] mv_xor f1060900.xor: Marvell shared XOR driver
[    5.064099][    T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    5.070224][    T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    5.073685][    T1] printk: console [ttyS0] disabled
[    5.074506][    T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 28, base_baud = 12500000) is a 16550A
[    5.074587][    T1] printk: console [ttyS0] enabled
[    6.077123][    T1] loop: module loaded
[    6.082363][    T1] sata_mv f1080000.sata: slots 32 ports 2
[    6.094068][    T1] scsi host0: sata_mv
[    6.099903][    T1] scsi host1: sata_mv
[    6.104443][    T1] ata1: SATA max UDMA/133 irq 29
[    6.109280][    T1] ata2: SATA max UDMA/133 irq 29
[    6.115912][    T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda
[    6.123064][    T1] nand: Samsung NAND 256MiB 3,3V 8-bit
[    6.128409][    T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    6.136779][    T1] Scanning device for bad blocks
[    6.328820][    T1] Bad eraseblock 1736 at 0x00000d900000
[    6.367953][    T1] 3 cmdlinepart partitions found on MTD device orion_nand
[    6.375013][    T1] Creating 3 MTD partitions on "orion_nand":
[    6.380944][    T1] 0x000000000000-0x000000100000 : "uboot"
[    6.387643][    T1] 0x000000100000-0x000000500000 : "kernel"
[    6.394351][    T1] 0x000000500000-0x000010000000 : "rootfs"
[    6.403487][    T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[    6.412159][    T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[    6.428241][    T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@8: Whitelisted compatible string. Please remove
[    6.444963][   T53] ata1: SATA link down (SStatus 0 SControl F300)
[    6.474235][    T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    6.802637][   T55] ata2: SATA link down (SStatus 0 SControl F300)
[    7.242515][    T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51
[    7.252845][    T1] orion-ehci f1050000.ehci: EHCI Host Controller
[    7.259121][    T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    7.267882][    T1] orion-ehci f1050000.ehci: irq 32, io mem 0xf1050000
[    7.300925][    T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    7.308166][    T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[    7.317229][    T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.325223][    T1] usb usb1: Product: EHCI Host Controller
[    7.330839][    T1] usb usb1: Manufacturer: Linux 6.5.7-kirkwood-tld-1 ehci_hcd
[    7.338214][    T1] usb usb1: SerialNumber: f1050000.ehci
[    7.344938][    T1] hub 1-0:1.0: USB hub found
[    7.349475][    T1] hub 1-0:1.0: 1 port detected
[    7.355482][    T1] usbcore: registered new interface driver usb-storage
[    7.363029][    T1] mousedev: PS/2 mouse device common for all mice
[    7.640931][   T50] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    7.842013][   T50] usb 1-1: New USB device found, idVendor=18a5, idProduct=0302, bcdDevice= 1.00
[    7.851001][   T50] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    7.858918][   T50] usb 1-1: Product: STORE N GO                    
[    7.865340][   T50] usb 1-1: Manufacturer: Verbatim                      
[    7.872214][   T50] usb 1-1: SerialNumber: 10J223000000411D
[    7.879066][   T50] usb-storage 1-1:1.0: USB Mass Storage device detected
[    7.887147][   T50] scsi host2: usb-storage 1-1:1.0
[    8.400938][    T1] rtc-mv f1010300.rtc: internal RTC not ticking
[    8.407475][    T1] i2c_dev: i2c /dev entries driver
[    8.417108][    T1] rtc-pcf8563 0-0051: registered as rtc0
[    8.424006][    T1] rtc-pcf8563 0-0051: setting system clock to 2025-02-10T18:19:48 UTC (1739211588)
[    8.435932][    T1] device-mapper: uevent: version 1.0.3
[    8.442106][    T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[    8.452125][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[    8.459402][    T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[    8.466850][    T1] device-mapper: multipath service-time: version 0.3.0 loaded
[    8.474335][    T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[    8.484819][    T1] ledtrig-cpu: registered to indicate activity on CPUs
[    8.491871][    T1] hid: raw HID events driver (C) Jiri Kosina
[    8.498322][    T1] drop_monitor: Initializing network drop monitor service
[    8.507301][    T1] NET: Registered PF_INET6 protocol family
[    8.515675][    T1] Segment Routing with IPv6
[    8.520082][    T1] RPL Segment Routing with IPv6
[    8.525047][    T1] In-situ OAM (IOAM) with IPv6
[    8.529916][    T1] NET: Registered PF_PACKET protocol family
[    8.536205][    T1] Key type dns_resolver registered
[    8.564766][    T1] registered taskstats version 1
[    8.569897][    T1] Loading compiled-in X.509 certificates
[    8.602396][    T1] Key type .fscrypt registered
[    8.607065][    T1] Key type fscrypt-provisioning registered
[    8.620813][    T1] Key type big_key registered
[    8.682101][    T1] Key type encrypted registered
[    8.818820][  T107] "cryptomgr_test" (107) uses obsolete ecb(arc4) skcipher
[    8.961990][   T18] scsi 2:0:0:0: Direct-Access     Verbatim STORE N GO       1.00 PQ: 0 ANSI: 2
[    8.983446][   T32] sd 2:0:0:0: [sda] 7831552 512-byte logical blocks: (4.01 GB/3.73 GiB)
[    9.001680][   T32] sd 2:0:0:0: [sda] Write Protect is off
[    9.020944][   T32] sd 2:0:0:0: [sda] No Caching mode page found
[    9.027008][   T32] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    9.047460][   T32]  sda: sda1
[    9.061275][   T32] sd 2:0:0:0: [sda] Attached SCSI removable disk
[   11.633319][    T1] clk: Disabling unused clocks
[   11.642627][    T1] Freeing unused kernel image (initmem) memory: 1024K
[   11.661987][    T1] Checked W+X mappings: passed, no W+X pages found
[   11.668410][    T1] Run /init as init process
Loading, please wait...
Starting systemd-udevd version 252.17-1~deb12u1
[   13.437877][  T157] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
done.
Gave up waiting for root file system device.  Common problems:
 - Boot args (cat /proc/cmdline)
   - Check rootdelay= (did the system wait long enough?)
 - Missing modules (cat /proc/modules; ls /dev)
ALERT!  LABEL=rootfs does not exist.  Dropping to a shell!


BusyBox v1.35.0 (Debian 1:1.35.0-4+b3) built-in shell (ash)
Enter 'help' for a list of built-in commands.

(initramfs) [   75.930948][    C0] random: crng init done

Guys, please help me, I don't know what to do

Reply Quote

bodhi

Re: Unbrick Stora MS2000
February 11, 2025 03:08AM

Admin
Registered: 14 years ago
Posts: 19,932

dmitrynino,

> [ 8.961990][ T18] scsi 2:0:0:0: Direct-Access
> Verbatim STORE N GO 1.00 PQ: 0 ANSI: 2
> [ 8.983446][ T32] sd 2:0:0:0: [sda] 7831552
> 512-byte logical blocks: (4.01 GB/3.73 GiB)
> [ 9.001680][ T32] sd 2:0:0:0: [sda] Write
> Protect is off
> [ 9.020944][ T32] sd 2:0:0:0: [sda] No
> Caching mode page found
> [ 9.027008][ T32] sd 2:0:0:0: [sda] Assuming
> drive cache: write through
> [ 9.047460][ T32] sda: sda1
> [ 9.061275][ T32] sd 2:0:0:0: [sda] Attached
> SCSI removable disk
> [ 11.633319][ T1] clk: Disabling unused
> clocks
> [ 11.642627][ T1] Freeing unused kernel image
> (initmem) memory: 1024K
> [ 11.661987][ T1] Checked W+X mappings:
> passed, no W+X pages found
> [ 11.668410][ T1] Run /init as init process
> Loading, please wait...
> Starting systemd-udevd version 252.17-1~deb12u1
> [ 13.437877][ T157] usbcore: registered new
> interface driver uas

When you get to this point, the USB has been enumerated OK. And the /boot folder was OK.

But perhaps the rootfs was not created correctly. Try recreating it again, following the steps very closely, being root user (not sudo), all the time while you formt and extract the tarball, using only command line tools (not GUI). Label the rootfs as rootfs.

If not successful booting after a few tries, use a different USB brand such as Sandisk, Transcend,....

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Reply Quote

dmitrynino

Re: Unbrick Stora MS2000
February 15, 2025 12:11PM

Registered: 9 months ago
Posts: 3

Hi Bodhi, thanks for the answer
I tried to do everything step by step described here: https://forum.doozan.com/read.php?2,138815
I got this log:

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__| 
 ** MARVELL BOARD: RD-88F6281A LE 

U-Boot 1.1.4 (Sep  4 2009 - 09:36:11) Marvell version: 3.4.14

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CEE60

Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz 

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size  64MB 
DRAM CS[1] base 0x04000000   size  64MB 
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
CRC in Flash: ffffffff, Calculated CRC: 619d86db
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
## Error: environment overflow, "stdin" deleted
## Error: environment overflow, "stdout" deleted
## Error: environment overflow, "stderr" deleted

CPU : Marvell Feroceon (Rev 1)
## Error: environment overflow, "console" deleted
## Error: environment overflow, "mainlineLinux" deleted
## Error: environment overflow, "CASset" deleted
## Error: environment overflow, "enaMonExt" deleted
## Error: environment overflow, "enaCpuStream" deleted
## Error: environment overflow, "enaWrAllo" deleted
## Error: environment overflow, "pexMode" deleted
## Error: environment overflow, "disL2Cache" deleted
## Error: environment overflow, "setL2CacheWT" deleted
## Error: environment overflow, "disL2Prefetch" deleted
## Error: environment overflow, "enaICPref" deleted
## Error: environment overflow, "enaDCPref" deleted
## Error: environment overflow, "sata_dma_mode" deleted
## Error: environment overflow, "MALLOC_len" deleted
## Error: environment overflow, "ethprime" deleted
## Error: environment overflow, "netbsd_en" deleted
## Error: environment overflow, "vxworks_en" deleted
## Error: environment overflow, "bootargs_root" deleted
## Error: environment overflow, "bootargs_end" deleted
## Error: environment overflow, "image_name" deleted
## Error: environment overflow, "bootcmd" deleted
## Error: environment overflow, "standalone" deleted
## Error: environment overflow, "bootdelay" deleted
## Error: environment overflow, "disaMvPnp" deleted
## Error: environment overflow, "disaMvPnp" deleted
## Error: environment overflow, "ethaddr" deleted
## Error: environment overflow, "ethmtu" deleted
## Error: environment overflow, "eth1addr" deleted
## Error: environment overflow, "eth1mtu" deleted
## Error: environment overflow, "mvPhoneConfig" deleted
## Error: environment overflow, "mvNetConfig" deleted
## Error: environment overflow, "usb0Mode" deleted
## Error: environment overflow, "yuk_ethaddr" deleted
## Error: environment overflow, "nandEcc" deleted
## Error: environment overflow, "hddPowerCtrl" deleted
## Error: environment overflow, "netretry" deleted
## Error: environment overflow, "rcvrip" deleted
## Error: environment overflow, "loadaddr" deleted
## Error: environment overflow, "autoload" deleted
## Error: environment overflow, "enaAutoRecovery" deleted

Streaming disabled 
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: device mode
PEX 0: interface detected no Link.
Net:   ## Error: environment overflow, "ethact" deleted
egiga0, egiga1## Error: environment overflow, "ethact" deleted

USB:   scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Trying to load image from USB flash drive using FAT FS
reading /flashware.img

** Unable to read "/flashware.img" from usb 0:1 **
Trying to load image from USB flash drive using ext2 FS partition 0
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:0 **
Trying to load image from USB flash drive using ext2 FS partition 1
....
.
......
............
.........................
...................................................
...........

1162592 bytes read
## Error: environment overflow, "filesize" deleted
Missing loadaddr environment variable assuming default (0x400000)!
Update bootcmd
## Error: environment overflow, "bootcmd" deleted
## Error: environment overflow, "console" deleted
Erasing Nand...Writing to Nand... done

bootcmd: setenv bootargs $(console) root=/dev/ram0 rootfstype=squashfs initrd=0x600000,0xffd00000 ramdisk_size=-3072 recovery=usb serverip=0.0.0.0; bootm 0x400000;
## Error: environment overflow, "bootcmd" deleted
Booting the image (@ 0x400000)...
Power Button is pressed!
MPP Sel: 00000530, Data IN Enable: 00020058, Data In Polarity: 00000040, Data In: 00000010
Power Button is released!
MAC: 00:01:82:81:CA:16, IP: 10.129.202.22
## Error: environment overflow, "ethaddr" deleted
## Error: environment overflow, "ipaddr" deleted
## Error: environment overflow, "serverip" deleted
## Error: environment overflow, "netmask" deleted
## Error: environment overflow, "image_name" deleted
## Error: environment overflow, "console" deleted
## Error: environment overflow, "bootargs_root" deleted
## Error: environment overflow, "rootpath" deleted
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `serverip' not set
## Error: environment overflow, "bootargs" deleted
## Booting image at 00800000 ...
Bad Magic Number
Marvell>> nand erase 0xA0000 0x60000         

NAND erase: device 0 offset 0xa0000, size 0x60000
Erasing at 0xe0000 -- 100% complete.
OK
Marvell>> nand write 0xA0000 0xA0000 0x60000

NAND write: device 0 offset 0xa0000, size 0x60000
 393216 bytes written: OK
Marvell>> reset

After the reset command, the store does not respond, if I load it again via kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.kwb, I get this log.

        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__| 
 ** MARVELL BOARD: RD-88F6281A LE 

U-Boot 1.1.4 (Sep  4 2009 - 09:36:11) Marvell version: 3.4.14

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CEE60

Soc: 88F6281 A0 (DDR2)
CPU running @ 800Mhz L2 running @ 266Mhz
SysClock = 266Mhz , TClock = 200Mhz 

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size  64MB 
DRAM CS[1] base 0x04000000   size  64MB 
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
CRC in Flash: 2444894c, Calculated CRC: e890e7d3
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++

CPU : Marvell Feroceon (Rev 1)

Streaming disabled 
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0, egiga1 [PRIME]
USB:   scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
Aquiring an IP address using DHCP...
egiga1 no link
egiga0 no link
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5

Retry count exceeded; starting again
egiga1 no link
egiga0 no link
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5

Retry count exceeded; starting again
egiga1 no link
egiga0 no link
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5

Retry count exceeded; starting again
Failed to retreive an IP address assuming default (169.254.100.100)!
Starting the Recovery process to retreive the file...
egiga1 no link
egiga0 no link
uImage load address 0x02000000
Warning: Missing environment variable "deviceName". Assuming default!
Warning: Missing environment variable "modelNumber". Assuming default!
Broadcasting Distress Beacon Packet.
Warning: Missing environment variable "deviceName". Assuming default!
Warning: Missing environment variable "modelNumber". Assuming default!
Broadcasting Distress Beacon Packet.
Warning: Missing environment variable "deviceName". Assuming default!
Warning: Missing environment variable "modelNumber". Assuming default!
Broadcasting Distress Beacon Packet.
Warning: Missing environment variable "deviceName". Assuming default!

I tried different USB, the result does not change.

Reply Quote

bodhi

Re: Unbrick Stora MS2000
February 15, 2025 09:23PM

Admin
Registered: 14 years ago
Posts: 19,932

dmitrynino,

You were doing great here:

https://forum.doozan.com/read.php?3,139098,139098#msg-139098

And I suggested what to do here:

https://forum.doozan.com/read.php?3,139098,139104#msg-139104

Don't try anything else.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Reply Quote

dmitrynino

Re: Unbrick Stora MS2000
February 16, 2025 05:23AM

Registered: 9 months ago
Posts: 3

Hi!
I did everything again and on another USB, here is my log:

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__| 
 ** MARVELL BOARD: RD-88F6281A LE 

U-Boot 1.1.4 (Sep  4 2009 - 09:36:11) Marvell version: 3.4.14

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CEE60

Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz 

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size  64MB 
DRAM CS[1] base 0x04000000   size  64MB 
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
CRC in Flash: 2444894c, Calculated CRC: e890e7d3
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++

CPU : Marvell Feroceon (Rev 1)

Streaming disabled 
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0, egiga1 [PRIME]
USB:   scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Trying to load image from USB flash drive using FAT FS
reading /flashware.img

** Unable to read "/flashware.img" from usb 0:1 **
Trying to load image from USB flash drive using ext2 FS partition 0
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:0 **
Trying to load image from USB flash drive using ext2 FS partition 1
....
.
......
............
.........................
...................................................
...........

1162592 bytes read
Update bootcmd
Erasing Nand...Writing to Nand... done

bootcmd: setenv bootargs $(console) root=/dev/ram0 rootfstype=squashfs initrd=0x2200000,0xffe1bd60 ramdisk_size=-1936 recovery=usb serverip=0.0.0.0; bootm 0x2000000;
Booting the image (@ 0x2000000)...
## Booting image at 02000000 ...
Bad Magic Number
Power Button is pressed!
MPP Sel: 00000530, Data IN Enable: 00020058, Data In Polarity: 00000040, Data In: 00000010
Power Button is released!
MAC: 00:01:D1:B9:05:E3, IP: 10.185.5.227
egiga1 no link
egiga0 no link
Using egiga1 device
TFTP from server 10.0.0.1; our IP address is 10.185.5.227
Filename 'uImage'.
Load address: 0x800000
Loading: T T T T T T T T T T 
Retry count exceeded; starting again
## Booting image at 00800000 ...
Bad Magic Number
Hit any key to stop autoboot:  0 
Usage:
usb     - USB sub-system

## Booting image at 02000000 ...
Bad Magic Number
Marvell>>

Reply Quote

Newer Topic Older Topic

Print View RSS

Author:

Your Email:

Subject:

Help information

BBcode help

Spam prevention:

Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.

Enter code:

Message: