Pogoplug E02 - Cold boot works but reboot doesn't March 16, 2014 12:03AM |
Registered: 10 years ago Posts: 3 |
U-Boot 2013.10 (Feb 21 2014 - 19:35:02)-tld-2 Pogo E02 gcc (Debian 4.6.3-14) 4.6.3 GNU ld (GNU Binutils for Debian) 2.22 Hit any key to stop autoboot: 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... READ_CAP ERROR EHCI timed out on TD - token=0xbe008d80 EHCI timed out on TD - token=0xbe008d80 EHCI timed out on TD - token=0xbe008d80 EHCI timed out on TD - token=0xbe008d80 EHCI timed out on TD - token=0xbe008d80 EHCI timed out on TD - token=0xbe008d80 2 Storage Device(s) found ** File not found /rescueme ** ** Unrecognized filesystem type ** UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 91 MiB UBI: number of good PEBs: 727 UBI: number of bad PEBs: 1 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 716 UBI: total number of reserved PEBs: 11 UBI: number of PEBs reserved for bad PEB handling: 7 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "rootfs", error -22 UBIFS error (pid 0): ubifs_mount: Error reading superblock on volume 'rootfs' errno=-22! ubifsmount - mount UBIFS volume Usage: ubifsmount <volume-name> - mount 'volume-name' volume 1 bytes read in 126 ms (0 Bytes/s) Found bootable drive on usb 0:1 3931528 bytes read in 259 ms (14.5 MiB/s) ** File not found /boot/uInitrd ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.13.6-1-ARCH Created: 2014-03-08 9:06:30 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3931464 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Starting kernel ...
U-Boot 2013.10 (Feb 21 2014 - 19:35:02)-tld-2 Pogo E02 gcc (Debian 4.6.3-14) 4.6.3 GNU ld (GNU Binutils for Debian) 2.22 Hit any key to stop autoboot: 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Device NOT ready Request Sense returned 02 04 01 READ_CAP ERROR EHCI timed out on TD - token=0xbe008d80 EHCI timed out on TD - token=0xbe008d80 EHCI timed out on TD - token=0xbe008d80 EHCI timed out on TD - token=0xbe008d80 EHCI timed out on TD - token=0xbe008d80 EHCI timed out on TD - token=0xbe008d80 1 Storage Device(s) found ** No partition table - usb 0 ** ** No partition table - usb 0 ** UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 91 MiB UBI: number of good PEBs: 727 UBI: number of bad PEBs: 1 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 716 UBI: total number of reserved PEBs: 11 UBI: number of PEBs reserved for bad PEB handling: 7 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "rootfs", error -22 UBIFS error (pid 0): ubifs_mount: Error reading superblock on volume 'rootfs' errno=-22! ubifsmount - mount UBIFS volume Usage: ubifsmount <volume-name> - mount 'volume-name' volume ** No partition table - usb 0 ** ** Bad device usb 1 ** ** Bad device usb 2 ** ** Bad device usb 3 ** ** No partition table - usb 0 ** ** No partition table - usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. NAND read: device 0 offset 0x100000, size 0x400000 4194304 bytes read: OK ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.3.2-kirkwide Created: 2012-10-29 22:52:12 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3627768 Bytes = 3.5 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Starting kernel ...
Device NOT ready Request Sense returned 02 04 01
# fw_printenv arcNumber=2097 baudrate=115200 console=ttyS0,115200 ethact=egiga0 ethaddr=00:25:31:04:85:56 force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi if_netconsole=ping $serverip ipaddr=192.168.1.137 led_error=orange blinking led_exit=green off led_init=green blinking machid=dd6 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) ncip=192.168.1.22 partition=nand0,2 pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi preboot=run if_netconsole start_netconsole rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi rescue_installed=1 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params serverip=192.168.1.22 start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=nc stdin=nc stdout=nc ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_device=0:1 usb_root=/dev/sda1 usb_rootdelay=10 usb_rootfstype=ext3 usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_scan_list=1 2 3 4 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset bootdelay=2 usb_init=run usb_scan
Re: Pogoplug E02 - Cold boot works but reboot doesn't March 16, 2014 01:11AM |
Admin Registered: 14 years ago Posts: 19,302 |
bootcmd=usb start; sleep 5; usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; resetIncrease the sleep period until you can boot without a "EHCI timed out on TD" message afte the 2nd "usb start". Or you could play with 3 "usb start"with sleep periods in between.
Re: Pogoplug E02 - Cold boot works but reboot doesn't March 16, 2014 01:33AM |
Registered: 10 years ago Posts: 3 |
Re: Pogoplug E02 - Cold boot works but reboot doesn't March 16, 2014 04:16PM |
Admin Registered: 14 years ago Posts: 19,302 |
Re: Pogoplug E02 - Cold boot works but reboot doesn't March 17, 2014 12:03AM |
Registered: 10 years ago Posts: 3 |
Re: Pogoplug E02 - Cold boot works but reboot doesn't March 17, 2014 12:36AM |
Admin Registered: 14 years ago Posts: 19,302 |
Re: Pogoplug E02 - Cold boot works but reboot doesn't March 27, 2014 08:21PM |
Admin Registered: 14 years ago Posts: 19,302 |
Re: Pogoplug E02 - Cold boot works but reboot doesn't March 28, 2014 09:14AM |
Registered: 12 years ago Posts: 232 |
Re: Pogoplug E02 - Cold boot works but reboot doesn't March 28, 2014 05:00PM |
Admin Registered: 14 years ago Posts: 19,302 |
Re: Pogoplug E02 - Cold boot works but reboot doesn't January 25, 2015 10:53AM |
Registered: 10 years ago Posts: 1 |
bootcmd=usb start; usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run usb_ready_retry=5
Re: Pogoplug E02 - Cold boot works but reboot doesn't January 25, 2015 12:08PM |
Admin Registered: 14 years ago Posts: 19,302 |
> bootcmd=usb start; usb start; run > force_rescue_bootcmd; run ubifs_bootcmd; run > usb_bootcmd; usb stop; run rescue_bootcmd; run > usb_ready_retry=5 >