Re: 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) February 23, 2018 03:40PM |
Admin Registered: 13 years ago Posts: 19,107 |
uname -a flash_erase --version dpkg -l | grep mtd-utils
Re: 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) March 21, 2018 09:50PM |
Registered: 6 years ago Posts: 183 |
debian login: root Password: Last login: Wed Mar 21 18:29:42 PDT 2018 on ttyS0 Linux debian 4.4.54-oxnas-tld-1 #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017 armv6l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors # pogoplug pro /dev/mtd0 0x00100000 0x20000 0x20000 root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00e00000 00020000 "boot" mtd1: 07200000 00020000 "data" root@debian:~# nanddump --noecc --omitoob -f mtd0 /dev/mtd0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00e00000... root@debian:~# fw_printenv > current_envs.txt root@debian:~# dmesg | grep -i 'bad' [ 1.668702] Scanning device for bad blocks [ 1.689141] Bad eraseblock 249 at 0x000001f20000 root@debian:~# cd /tmp root@debian:/tmp# tar -xf uboot.2015.10-tld-2.ox820.bodhi.tar tar: uboot.2015.10-tld-2.ox820.bodhi.tar: Cannot open: No such file or directory tar: Error is not recoverable: exiting now root@debian:/tmp#
Re: 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) March 21, 2018 10:15PM |
Admin Registered: 13 years ago Posts: 19,107 |
Quote
Download U-Boot image at Dropbox
Re: 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) March 21, 2018 10:35PM |
Registered: 6 years ago Posts: 183 |
root@debian:/# ls . .. TEMP bin boot config-4.4.89-oxnas-tld-1 dev etc home lib linux-4.4.89-oxnas-tld-1.patch linux-dtb-4.4.89-oxnas-tld-1.tar linux-headers-4.4.89-oxnas-tld-1_1.0_armel.deb linux-image-4.4.89-oxnas-tld-1_1.0_armel.deb lost+found media mnt opt proc root run sbin srv sys tmp uboot.2015.10-tld-2.ox820.bodhi.tar uboot.2015.10-tld-2.ox820.environment uboot.2015.10-tld-2.ox820.environment.img uboot.2015.10-tld-2.ox820.mtd0.img uboot.spl.2013.10.ox820.850mhz.mtd0.img usr var zImage-4.4.89-oxnas-tld-1 root@debian:/#
# picocom -b 115200 /dev/ttyUSB0 picocom v2.2 port is : /dev/ttyUSB0 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 stopbits are : 1 escape is : C-a local echo is : no noinit is : no noreset is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv -E imap is : omap is : emap is : crcrlf,delbs, Type [C-a] [C-h] to see available commands Terminal ready 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Reset IDE: U-Boot SPL 2013.10-tld-4 (Sep 07 2014 - 14:10:12) Boot device: NAND Attempting to set PLLA to 850 MHz ... plla_ctrl0 : 0000020a plla_ctrl1 : 00330000 plla_ctrl2 : 0065008b plla_ctrl3 : 000000f1 PLLA Set U-Boot 2015.10-tld-2 (Oct 21 2017 - 22:00:02 -0700) OXNAS OX820 DRAM: 128 MiB NAND: 128 MiB In: serial Out: serial Err: serial Net: dwmac.40400000 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Reset IDE: SATA PHY not ready for device 0 ide_preinit failed Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 15630336 4f02bf5a-01 83 Boot loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** no IDE devices available running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 221 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 4621824 bytes read in 526 ms (8.4 MiB/s) loading uInitrd ... 4594376 bytes read in 564 ms (7.8 MiB/s) loading DTB /boot/dts/ox820-pogoplug-pro.dtb ... 7067 bytes read in 259 ms (26.4 KiB/s) ## Booting kernel from Legacy Image at 60500000 ... Image Name: Linux-4.4.117-oxnas-tld-1 Created: 2018-03-21 1:30:52 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4621760 Bytes = 4.4 MiB Load Address: 60008000 Entry Point: 60008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 60e00000 ... Image Name: initramfs-4.4.117-oxnas-tld-1 Created: 2018-03-21 1:32:26 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 4594312 Bytes = 4.4 MiB Load Address: 60000000 Entry Point: 60000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 62c00000 Booting using the fdt blob at 0x62c00000 Loading Kernel Image ... OK Loading Ramdisk to 679c5000, end 67e26a88 ... OK Loading Device Tree to 679c0000, end 679c4b9a ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017 [ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Pogoplug V3 Pro [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map [ 0.000000] PERCPU: Embedded 12 pages/cpu @c7eda000 s17696 r8192 d23264 u49152 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 116204K/131072K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 14868K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0827e14 (8320 kB) [ 0.000000] .init : 0xc0828000 - 0xc0860000 ( 224 kB) [ 0.000000] .data : 0xc0860000 - 0xc08a8378 ( 289 kB) [ 0.000000] .bss : 0xc08a8378 - 0xc08e6350 ( 248 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:160 [ 0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns [ 0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns [ 0.000163] Console: colour dummy device 80x30 [ 0.000197] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744) [ 0.050019] pid_max: default: 32768 minimum: 301 [ 0.050186] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.050204] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.051023] Initializing cgroup subsys net_cls [ 0.051105] CPU: Testing write buffer coherency: ok [ 0.051530] Setting up static identity map for 0x60008220 - 0x60008258 [ 0.190136] Brought up 2 CPUs [ 0.190159] SMP: Total of 2 processors activated (678.29 BogoMIPS). [ 0.190945] devtmpfs: initialized [ 0.196339] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.196385] futex hash table entries: 512 (order: 2, 16384 bytes) [ 0.196700] prandom: seed boundary self test passed [ 0.201116] prandom: 100 self tests passed [ 0.201144] pinctrl core: initialized pinctrl subsystem [ 0.201943] NET: Registered protocol family 16 [ 0.202501] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.230021] cpuidle: using governor ladder [ 0.260014] cpuidle: using governor menu [ 0.265216] gpio-oxnas 44000000.gpio: at address c8848000 [ 0.265607] gpio-oxnas 44100000.gpio: at address c884a000 [ 0.266158] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver [ 0.389219] oxnas-pcie 47c00000.pcie-controller: PCIe version/deviceID 0x82510b5 [ 0.389337] oxnas-pcie 47c00000.pcie-controller: link up [ 0.389655] oxnas-pcie 47c00000.pcie-controller: PCI host bridge to bus 0000:00 [ 0.389683] pci_bus 0000:00: root bus resource [mem 0x48000000-0x49ffffff] [ 0.389701] pci_bus 0000:00: root bus resource [mem 0x4a000000-0x4bdfffff pref] [ 0.389719] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] [ 0.389736] pci_bus 0000:00: root bus resource [bus 00-7f] [ 0.390341] PCI: bus0: Fast back to back transfers disabled [ 0.390430] pci 0000:00:00.0: BAR 0: assigned [mem 0x48000000-0x4800ffff] [ 0.390891] vgaarb: loaded [ 0.391383] SCSI subsystem initialized [ 0.392243] usbcore: registered new interface driver usbfs [ 0.392350] usbcore: registered new interface driver hub [ 0.392506] usbcore: registered new device driver usb [ 0.392727] pps_core: LinuxPPS API ver. 1 registered [ 0.392742] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.392791] PTP clock support registered [ 0.394951] clocksource: Switched to clocksource rps_clocksource_timer [ 0.413424] NET: Registered protocol family 2 [ 0.414320] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.414361] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 0.414397] TCP: Hash tables configured (established 1024 bind 1024) [ 0.414497] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.414543] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.414812] NET: Registered protocol family 1 [ 0.415349] RPC: Registered named UNIX socket transport module. [ 0.415370] RPC: Registered udp transport module. [ 0.415380] RPC: Registered tcp transport module. [ 0.415390] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.415787] Unpacking initramfs... [ 0.890467] Freeing initrd memory: 4488K (c79c5000 - c7e27000) [ 0.891947] Initialise system trusted keyring [ 0.905070] zbud: loaded [ 0.910456] NFS: Registering the id_resolver key type [ 0.910517] Key type id_resolver registered [ 0.910533] Key type id_legacy registered [ 0.910579] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.910604] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.911587] fuse init (API version 7.23) [ 0.913594] Key type big_key registered [ 0.990748] Key type asymmetric registered [ 0.990784] Asymmetric key parser 'x509' registered [ 0.990917] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.990940] io scheduler noop registered [ 0.990960] io scheduler deadline registered [ 0.991022] io scheduler cfq registered (default) [ 0.991700] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.993274] console [ttyS0] disabled [ 0.993374] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 390625) is a 16550A [ 1.576570] console [ttyS0] enabled [ 1.591482] loop: module loaded [ 1.596587] scsi host0: sata_oxnas [ 1.600473] ata1: SATA max UDMA/133 irq 7 [ 1.604567] sata_oxnas: resetting SATA core [ 1.605649] nand: Could not find valid ONFI parameter page; aborting [ 1.605690] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 1.605696] nand: Hynix NAND 128MiB 3,3V 8-bit [ 1.605703] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.605721] Scanning device for bad blocks [ 1.625676] Bad eraseblock 249 at 0x000001f20000 [ 1.687449] 2 cmdlinepart partitions found on MTD device 41000000.nand [ 1.693977] Creating 2 MTD partitions on "41000000.nand": [ 1.699358] 0x000000000000-0x000000e00000 : "boot" [ 1.706124] 0x000000e00000-0x000008000000 : "data" [ 1.713497] oxnas-gmac 40400000.ethernet: no reset control found [ 1.719482] stmmac - user ID: 0x12, Synopsys ID: 0x35 [ 1.724554] Ring mode enabled [ 1.727595] DMA HW capability register supported [ 1.732126] Enhanced/Alternate descriptors [ 1.736458] Enabled extended descriptors [ 1.740464] RX Checksum Offload Engine supported (type 2) [ 1.745922] TX Checksum insertion supported [ 1.750184] Wake-Up On Lan supported [ 1.753830] Enable RX Mitigation via HW Watchdog Timer [ 1.784750] libphy: stmmac: probed [ 1.788144] eth%d: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active [ 1.794606] eth%d: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03) [ 1.801346] PPP generic driver version 2.4.2 [ 1.806026] rt2800pci 0000:00:00.0: enabling device (0140 -> 0142) [ 1.812428] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3090, rev 3213 detected [ 1.823631] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected [ 1.832852] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.839365] ehci-pci: EHCI PCI platform driver [ 1.844259] oxnas-ehci 40200100.ehci: EHCI Host Controller [ 1.849758] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1 [ 1.857623] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100 [ 1.880002] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00 [ 1.886312] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.893117] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.900336] usb usb1: Product: EHCI Host Controller [ 1.905195] usb usb1: Manufacturer: Linux 4.4.54-oxnas-tld-1 ehci_hcd [ 1.911626] usb usb1: SerialNumber: 40200100.ehci [ 1.917317] hub 1-0:1.0: USB hub found [ 1.921175] hub 1-0:1.0: 2 ports detected [ 1.926320] usbcore: registered new interface driver cdc_acm [ 1.932016] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.940134] usbcore: registered new interface driver cdc_wdm [ 1.945937] usbcore: registered new interface driver usb-storage [ 1.952153] usbcore: registered new interface driver usbserial [ 1.958018] usbcore: registered new interface driver usbserial_generic [ 1.964615] usbserial: USB Serial support registered for generic [ 1.971087] mousedev: PS/2 mouse device common for all mice [ 1.976811] i2c /dev entries driver [ 1.981698] hidraw: raw HID events driver (C) Jiri Kosina [ 1.987322] usbcore: registered new interface driver usbhid [ 1.992929] usbhid: USB HID core driver [ 1.998796] NET: Registered protocol family 10 [ 2.010158] ata1: SATA link down (SStatus 0 SControl 310) [ 2.020945] sit: IPv6 over IPv4 tunneling driver [ 2.026560] NET: Registered protocol family 17 [ 2.031260] Key type dns_resolver registered [ 2.036915] registered taskstats version 1 [ 2.041080] Loading compiled-in X.509 certificates [ 2.045967] zswap: loaded using pool lzo/zbud [ 2.064947] Key type encrypted registered [ 2.072102] Freeing unused kernel memory: 224K (c0828000 - c0860000) Loading, please wait... [ 2.240051] usb 1-1: new high-speed USB device number 2 using oxnas-ehci starting version 232 [ 2.256634] random: systemd-udevd: uninitialized urandom read (16 bytes read, 0 bits of entropy available) [ 2.267914] random: systemd-udevd: uninitialized urandom read (16 bytes read, 0 bits of entropy available) [ 2.268971] random: udevadm: uninitialized urandom read (16 bytes read, 0 bits of entropy available) [ 2.271280] random: udevadm: uninitialized urandom read (16 bytes read, 0 bits of entropy available) [ 2.271464] random: udevadm: uninitialized urandom read (16 bytes read, 0 bits of entropy available) [ 2.272624] random: udevadm: uninitialized urandom read (16 bytes read, 0 bits of entropy available) [ 2.273684] random: udevadm: uninitialized urandom read (16 bytes read, 0 bits of entropy available) [ 2.277739] random: udevadm: uninitialized urandom read (16 bytes read, 0 bits of entropy available) [ 2.278760] random: udevadm: uninitialized urandom read (16 bytes read, 0 bits of entropy available) [ 2.279715] random: udevadm: uninitialized urandom read (16 bytes read, 0 bits of entropy available) [ 2.442078] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 2.448768] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 2.480204] usb 1-1: Product: USB2.0 Hub [ 2.492039] hub 1-1:1.0: USB hub found [ 2.500213] hub 1-1:1.0: 4 ports detected [ 2.586283] rt2800pci 0000:00:00.0 wlp0s0: renamed from wlan0 [ 2.800145] usb 1-1.3: new high-speed USB device number 3 using oxnas-ehci [ 2.931151] usb 1-1.3: New USB device found, idVendor=0781, idProduct=5530 [ 2.938007] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.945331] usb 1-1.3: Product: Cruzer [ 2.949066] usb 1-1.3: Manufacturer: SanDisk [ 2.953359] usb 1-1.3: SerialNumber: 20053248121181F0AC47 [ 2.960227] usb-storage 1-1.3:1.0: USB Mass Storage device detected [ 2.967045] scsi host1: usb-storage 1-1.3:1.0 [ 2.986777] usbcore: registered new interface driver uas Begin: Loading essential drivers ... done. [ 3.971261] scsi 1:0:0:0: Direct-Access SanDisk Cruzer 1.20 PQ: 0 ANSI: 5 [ 3.987658] sd 1:0:0:0: [sda] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB) [ 3.997388] sd 1:0:0:0: [sda] Write Protect is off [ 4.007508] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 4.027438] sda: sda1 [ 4.041889] sd 1:0:0:0: [sda] Attached SCSI removable disk Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.29.2 [/sbin/fsck.ext4 (1) -- /dev/sda1] fsck.ext4 -a -C0 /dev/sda1 rootfs: recovering journal rootfs: clean, 14035/488640 files, 181527/1953792 blocks done. [ 13.410416] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ ok ] Synthesizing the initial hotplug events...done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Activating swap...done. [ 17.422397] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 17.962972] random: nonblocking pool is initialized [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.29.2 done. [ ok ] Loading kernel modules...done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/edited for security Sending on LPF/eth0/edited for security Sending on Socket/fallback DHCPREQUEST of 192.edited for security on eth0 to 255.255.255.255 port 67 [ 26.130150] oxnas-gmac 40400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off DHCPREQUEST of 192.edited for security on eth0 to 255.255.255.255 port 67 DHCPACK of 192.edited for security from 192.edited for security bound to 192.edited for security -- renewal in 16565 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1245 (syslogd) . ok [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting system message bus: dbus. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1244 (klogd) . ok [ ok ] Starting NTP server: ntpd. Debian GNU/Linux 9 debian ttyS0 debian login: root Password: Last login: Wed Mar 21 20:46:45 PDT 2018 on ttyS0 Linux debian 4.4.54-oxnas-tld-1 #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017 armv6l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~#
Re: 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) March 22, 2018 12:06AM |
Admin Registered: 13 years ago Posts: 19,107 |
Re: 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) July 21, 2018 05:04PM |
Admin Registered: 13 years ago Posts: 19,107 |
Derek
Re: 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) July 25, 2018 12:34AM |
root@pogoplug:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000 root@pogoplug:~# cat /proc/mtd dev: size erasesize name mtd0: 00200000 00020000 "u-boot" mtd1: 00300000 00020000 "uImage" mtd2: 00300000 00020000 "uImage2" mtd3: 00800000 00020000 "failsafe" mtd4: 07000000 00020000 "root" mtd5: 00010000 00008000 "spi0.0" root@pogoplug:~# dmesg | grep -i 'bad' [ 4.121566] Scanning device for bad blocks
Re: 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) July 25, 2018 03:27AM |
Admin Registered: 13 years ago Posts: 19,107 |
Derek
Re: 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) July 25, 2018 09:55PM |
Re: 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) July 31, 2018 01:24PM |
Registered: 6 years ago Posts: 5 |
Re: 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) July 31, 2018 02:04PM |
Admin Registered: 13 years ago Posts: 19,107 |
Re: 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) July 31, 2018 11:22PM |
Admin Registered: 13 years ago Posts: 19,107 |
mari8b
Re: 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) August 09, 2018 06:28AM |
Re: 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) August 09, 2018 08:26AM |
Admin Registered: 13 years ago Posts: 19,107 |