Totaly f***ed up my Goflex Home uBoot October 03, 2014 05:02PM |
Registered: 9 years ago Posts: 8 |
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:41:47) Seagate GoFlex Home SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: nc Out: nc Err: nc
Re: Totaly f***ed up my Goflex Home uBoot October 04, 2014 12:10AM |
Admin Registered: 13 years ago Posts: 18,623 |
Quote
> I have working UART, but all i see is:
>
>> U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:41:47) > Seagate GoFlex Home > > SoC: Kirkwood 88F6281_A1 > DRAM: 128 MiB > WARNING: Caches not enabled > NAND: 256 MiB > In: nc > Out: nc > Err: nc >>
> looks like serial console is completely
> disabled…
Quote
> In: nc
> Out: nc
> Err: nc
Re: Totaly f***ed up my Goflex Home uBoot October 04, 2014 03:25AM |
Registered: 9 years ago Posts: 8 |
Re: Totaly f***ed up my Goflex Home uBoot October 04, 2014 04:00AM |
Admin Registered: 13 years ago Posts: 18,623 |
stderr=nc stdin=nc stdout=nc preboot=So netconsole did not start (preboot could have been set to something wrong or empty, likewise with ipaddr and serverip), but input/output are set to netconsole.
Re: Totaly f***ed up my Goflex Home uBoot October 04, 2014 04:12AM |
Registered: 9 years ago Posts: 8 |
Re: Totaly f***ed up my Goflex Home uBoot October 04, 2014 04:29AM |
Admin Registered: 13 years ago Posts: 18,623 |
Re: Totaly f***ed up my Goflex Home uBoot October 04, 2014 04:47AM |
Registered: 9 years ago Posts: 8 |
Re: Totaly f***ed up my Goflex Home uBoot October 04, 2014 03:54PM |
Registered: 9 years ago Posts: 8 |
Re: Totaly f***ed up my Goflex Home uBoot October 04, 2014 05:07PM |
Admin Registered: 13 years ago Posts: 18,623 |
Re: Totaly f***ed up my Goflex Home uBoot October 04, 2014 05:20PM |
Registered: 9 years ago Posts: 8 |
Re: Totaly f***ed up my Goflex Home uBoot October 04, 2014 06:10PM |
Admin Registered: 13 years ago Posts: 18,623 |
Re: Totaly f***ed up my Goflex Home uBoot October 04, 2014 08:18PM |
Admin Registered: 13 years ago Posts: 18,623 |
Re: Totaly f***ed up my Goflex Home uBoot October 05, 2014 03:39AM |
Registered: 9 years ago Posts: 8 |
U-Boot 2014.07-tld-2-uart-rescue (Oct 04 2014 - 17:28:55) Seagate GoFlex Home SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 256 MiB In: nc Out: nc Err: nc Hit any key to stop autoboot: 0 GoFlexHome>:) nice work.
arcNumber=3338 baudrate=115200 bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run sata_bootcmd; run rescue_bootcmd; run pogo_bootcmd; reset bootdelay=10 console=ttyS0,115200 ethact=egiga0 ethaddr=00:10:75:2f:3e:99 force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ipaddr=10.10.10.6 led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) nc_start=setenv stdin nc; setenv stdout nc; setenv stderr nc; version nc_test=ping $ncip ncip=10.10.10.5 ncipk=10.10.10.4 partition=nand0,2 pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi preboot=setenv stderr serial; setenv stdin serial; setenv stdout serial; setenv baudrate 115200; setenv console ttyS0,115200; setenv bootdelay 10 rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params sata_boot=ide reset; mw 0x800000 0 1; ext2load ide $sata_device 0x800000 /boot/uImage; if ext2load ide $sata_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_bootcmd=run sata_set_bootargs; run sata_boot sata_device=0:1 sata_root=/dev/sda1 sata_rootdelay=10 sata_rootfstype=ext3 sata_set_bootargs=setenv bootargs console=$console root=$sata_root rootdelay=$sata_rootdelay rootfstype=$sata_rootfstype $mtdparts $sata_custom_params serverip=10.10.10.3 stderr=serial stdin=serial stdout=serial ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_custom_params=ignore_loglevel netconsole=6665@10.10.10.3/eth0,6666@10.10.10.4/ usb_device=0:1 usb_init=run usb_scan usb_root=/dev/sda1 usb_rootdelay=10 usb_rootfstype=ext4 usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_scan_list=1 2 3 4 usb_set_bootargs=setenv bootargs console=$console root=/dev/disk/by-label/urootfs rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params Environment size: 3269/131068 bytes
GoFlexHome>usb start GoFlexHome>mw 0x800000 0 1; ext2load usb 0:1 0x800000 /boot/uImage; if ext2load usb 0:1 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi 2756040 bytes read in 382 ms (6.9 MiB/s) 6032465 bytes read in 477 ms (12.1 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.16.0-kirkwood-tld-2 Created: 2014-09-01 23:18:31 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2755976 Bytes = 2.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.16.0-kirkwood-tld-2 Created: 2014-09-01 23:18:48 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6032401 Bytes = 5.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel.
Re: Totaly f***ed up my Goflex Home uBoot October 05, 2014 01:19PM |
Admin Registered: 13 years ago Posts: 18,623 |
Re: Totaly f***ed up my Goflex Home uBoot October 12, 2014 04:23AM |
Registered: 9 years ago Posts: 8 |
Re: Totaly f***ed up my Goflex Home uBoot October 12, 2014 05:02AM |
Admin Registered: 13 years ago Posts: 18,623 |