U-Boot VAMP 0.6 Pogoplug V4
Posted by rustyspoons
|
U-Boot VAMP 0.6 Pogoplug V4 October 21, 2014 07:37AM |
Registered: 9 years ago Posts: 22 |
I have a collection of Pogoplugs thank's to the great U-Boot on here, brilliant little devices.
I also have serial access on them all.
On one of them I run VAMP 0.6 as a music player, I have tried a squeezelite install on ARCH/Debian but it does not seem to work as well as the Fedora based VAMP image that they have created on Vortexbox.
As the E02 is getting harder to find, I have ordered a V4 device, I would like to stick this in the AV rack and use it as just a music player.
The VAMP install is based on a Doozan U-Boot with modified environments, I would love to get VAMP running on a V4 but I believe the U-Boot is different, will the environments script in this guide work? or will I brick the V4
http://vortexbox.org/forum/vortexbox/general/51318-install-vamp-0-6
If it's a no go, what's required to get this image running on a V4, it looks a perfect device to run as a Squeezebox player, I am not bothered whether it will SD or USB boot, SD would be nice though.
Any help would be gratefully appreciated, keep up the good work :)
I also have serial access on them all.
On one of them I run VAMP 0.6 as a music player, I have tried a squeezelite install on ARCH/Debian but it does not seem to work as well as the Fedora based VAMP image that they have created on Vortexbox.
As the E02 is getting harder to find, I have ordered a V4 device, I would like to stick this in the AV rack and use it as just a music player.
The VAMP install is based on a Doozan U-Boot with modified environments, I would love to get VAMP running on a V4 but I believe the U-Boot is different, will the environments script in this guide work? or will I brick the V4
http://vortexbox.org/forum/vortexbox/general/51318-install-vamp-0-6
/usr/sbin/fw_setenv usb_scan 'usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done' /usr/sbin/fw_setenv usb_boot 'mw 0x800000 0 1; ext2load usb $usb_device 0x800000 uImage; if ext2load usb $usb_device 0x1100000 uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi' /usr/sbin/fw_setenv usb_scan_1 "usb=0:1 dev=sda3" /usr/sbin/fw_setenv usb_scan_2 "usb=1:1 dev=sdb3" /usr/sbin/fw_setenv usb_scan_3 "usb=2:1 dev=sdc3" /usr/sbin/fw_setenv usb_scan_4 "usb=3:1 dev=sdd3" /usr/sbin/fw_setenv usb_rootfstype ext4
If it's a no go, what's required to get this image running on a V4, it looks a perfect device to run as a Squeezebox player, I am not bothered whether it will SD or USB boot, SD would be nice though.
Any help would be gratefully appreciated, keep up the good work :)
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 21, 2014 11:42AM |
Admin Registered: 13 years ago Posts: 18,550 |
rustyspoons,
> will the environments script in this
> guide work? or will I brick the V4
>
> http://vortexbox.org/forum/vortexbox/general/51318
> -install-vamp-0-6
You will brick it with that procedure! See this u-boot:
http://forum.doozan.com/read.php?3,12381
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> will the environments script in this
> guide work? or will I brick the V4
>
> http://vortexbox.org/forum/vortexbox/general/51318
> -install-vamp-0-6
You will brick it with that procedure! See this u-boot:
http://forum.doozan.com/read.php?3,12381
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 21, 2014 12:03PM |
Registered: 9 years ago Posts: 22 |
bodhi Wrote:
-------------------------------------------------------
> rustyspoons,
>
> > will the environments script in this
> > guide work? or will I brick the V4
> >
> >
> http://vortexbox.org/forum/vortexbox/general/51318
>
> > -install-vamp-0-6
>
> You will brick it with that procedure! See this
> u-boot:
> http://forum.doozan.com/read.php?3,12381
Hi Bodhi,
Thanks for your reply, I wasn't going to use the U-Boot from the VAMP link, but the one on here, will the environment script in that link with the U-Boot you listed?
Cheers
Edited 1 time(s). Last edit at 10/21/2014 01:13PM by rustyspoons.
-------------------------------------------------------
> rustyspoons,
>
> > will the environments script in this
> > guide work? or will I brick the V4
> >
> >
> http://vortexbox.org/forum/vortexbox/general/51318
>
> > -install-vamp-0-6
>
> You will brick it with that procedure! See this
> u-boot:
> http://forum.doozan.com/read.php?3,12381
Hi Bodhi,
Thanks for your reply, I wasn't going to use the U-Boot from the VAMP link, but the one on here, will the environment script in that link with the U-Boot you listed?
Cheers
Edited 1 time(s). Last edit at 10/21/2014 01:13PM by rustyspoons.
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 12:32AM |
Admin Registered: 13 years ago Posts: 18,550 |
rustyspoons,
Please read the 1st post of that thread. If you are unsure about any part, post your questions here.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Please read the 1st post of that thread. If you are unsure about any part, post your questions here.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 02:07AM |
Registered: 9 years ago Posts: 22 |
Sorry just realised there was a word missing in my reply and didn't make sense.
In my original post I put environment commands in a code box, which is what's needed to boot the image.
I wanted to know if that environment is compatible with the U-Boot for the V4, I know those strings work with the U-Boot for the E02 with the U-Boot from here.
However the VAMP image will not boot on an E02 unless you specify those environmental strings.
Will they work with the V4 U-Boot or are there some changes I need to make or are there alternative commands.
I'm not sure exactly which string is the one that gets VAMP to boot.
Thanks,
Dale
In my original post I put environment commands in a code box, which is what's needed to boot the image.
I wanted to know if that environment is compatible with the U-Boot for the V4, I know those strings work with the U-Boot for the E02 with the U-Boot from here.
However the VAMP image will not boot on an E02 unless you specify those environmental strings.
Will they work with the V4 U-Boot or are there some changes I need to make or are there alternative commands.
I'm not sure exactly which string is the one that gets VAMP to boot.
Thanks,
Dale
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 02:41AM |
Admin Registered: 13 years ago Posts: 18,550 |
@Dale,
With the new u-boot you can set whatever envs you need. If it's a Fedora image, then it should boot without problem. However, as always, it is prudent to try it out without flashing to NAND if you can. The Pogo V4 has UART booting, so you should try that since you have serial console. As instructed in the 1st post of my u-boot thread:
So download the u-boot image for Pogo V4, and kwboot. Try UART booting, and interrupt serial console, enter those envs that you know needed for booting the VAMP image. And boot it. If you booted into VAMP, then in VAMP, you should be able to flash this u-boot for real. The important part is UART booting, once you know you can do that, flashing u-boot manually is safe to do.
Also see here for how to boot UART with the Pogo V4 (a little bit trickier than other boxes):
http://forum.doozan.com/read.php?3,18153,18200#msg-18200
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 10/22/2014 02:43AM by bodhi.
With the new u-boot you can set whatever envs you need. If it's a Fedora image, then it should boot without problem. However, as always, it is prudent to try it out without flashing to NAND if you can. The Pogo V4 has UART booting, so you should try that since you have serial console. As instructed in the 1st post of my u-boot thread:
Quote
Important Note: If possible, try to test this boot image with UART booting before flashing to NAND. See davygravy's UART booting using kwboot instruction: here in this thread.
So download the u-boot image for Pogo V4, and kwboot. Try UART booting, and interrupt serial console, enter those envs that you know needed for booting the VAMP image. And boot it. If you booted into VAMP, then in VAMP, you should be able to flash this u-boot for real. The important part is UART booting, once you know you can do that, flashing u-boot manually is safe to do.
Also see here for how to boot UART with the Pogo V4 (a little bit trickier than other boxes):
http://forum.doozan.com/read.php?3,18153,18200#msg-18200
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 10/22/2014 02:43AM by bodhi.
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 03:30AM |
Registered: 9 years ago Posts: 22 |
bodhi Wrote:
-------------------------------------------------------
> @Dale,
>
> With the new u-boot you can set whatever envs you
> need. If it's a Fedora image, then it should boot
> without problem. However, as always, it is prudent
> to try it out without flashing to NAND if you can.
> The Pogo V4 has UART booting, so you should try
> that since you have serial console. As instructed
> in the 1st post of my u-boot thread:
>
>
> So download the u-boot image for Pogo V4, and
> kwboot. Try UART booting, and interrupt serial
> console, enter those envs that you know needed for
> booting the VAMP image. And boot it. If you booted
> into VAMP, then in VAMP, you should be able to
> flash this u-boot for real. The important part is
> UART booting, once you know you can do that,
> flashing u-boot manually is safe to do.
>
> Also see here for how to boot UART with the Pogo
> V4 (a little bit trickier than other boxes):
> http://forum.doozan.com/read.php?3,18153,18200#msg
> -18200
Thanks Bodhi,
Very informative information,
Will report back when I get this working, should make a lot of VAMP users happy if this will work on a V4 :D
-------------------------------------------------------
> @Dale,
>
> With the new u-boot you can set whatever envs you
> need. If it's a Fedora image, then it should boot
> without problem. However, as always, it is prudent
> to try it out without flashing to NAND if you can.
> The Pogo V4 has UART booting, so you should try
> that since you have serial console. As instructed
> in the 1st post of my u-boot thread:
>
>
>Quote
Important Note: If possible, try to test
> this boot image with UART booting before flashing
> to NAND. See davygravy's UART booting using kwboot
> instruction: here in this thread.
> So download the u-boot image for Pogo V4, and
> kwboot. Try UART booting, and interrupt serial
> console, enter those envs that you know needed for
> booting the VAMP image. And boot it. If you booted
> into VAMP, then in VAMP, you should be able to
> flash this u-boot for real. The important part is
> UART booting, once you know you can do that,
> flashing u-boot manually is safe to do.
>
> Also see here for how to boot UART with the Pogo
> V4 (a little bit trickier than other boxes):
> http://forum.doozan.com/read.php?3,18153,18200#msg
> -18200
Thanks Bodhi,
Very informative information,
Will report back when I get this working, should make a lot of VAMP users happy if this will work on a V4 :D
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 03:42AM |
Admin Registered: 13 years ago Posts: 18,550 |
> Will report back when I get this working, should
> make a lot of VAMP users happy if this will work
> on a V4 :D
That would be cool :) I'll give you a hand whenever you need an answer in setting up u-boot for that.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> make a lot of VAMP users happy if this will work
> on a V4 :D
That would be cool :) I'll give you a hand whenever you need an answer in setting up u-boot for that.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 06:42AM |
Registered: 9 years ago Posts: 22 |
Bodhi,
I have your UBOOT installed and also have a working copy of Debian on a flash stick, device is working fine, can boot to Debian perfectly, got root access and SSH.
It will not boot from VAMP image as I expected, the green light flashes then flashes red and re-boots, I just need to figure out what the environment differences are to boot the VAMP image.
Thanks,
Dale
I have your UBOOT installed and also have a working copy of Debian on a flash stick, device is working fine, can boot to Debian perfectly, got root access and SSH.
It will not boot from VAMP image as I expected, the green light flashes then flashes red and re-boots, I just need to figure out what the environment differences are to boot the VAMP image.
Thanks,
Dale
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 08:34AM |
Registered: 9 years ago Posts: 22 |
This is what I get if I manually insert the environemnts listed in Post 1 and try and boot the VAMP image.
Current Printenv:
Edited 1 time(s). Last edit at 10/22/2014 09:31AM by rustyspoons.
Pogov4> boot
b o o t
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
** Bad device usb 0x800000 **
** Bad device usb 0x1100000 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
** Bad device mmc 0 **
** Bad device mmc 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Reset IDE: ide_preinit failed
** Bad device size - ide 0 **
** Bad device size - ide 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
resetting ...
Current Printenv:
Pogov4> printenv p r i n t e n v arcNumber=3960 baudrate=115200 bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 ethaddr=00:25:31:05:2a:77 if_netconsole=ping $serverip ipaddr=192.168.1.10 led_error=orange blinking led_exit=green off led_init=green blinking machid=F78 mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) ncip=192.168.1.100 partition=nand0,2 preboot=run if_netconsole start_netconsole preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 serverip=192.168.1.100 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=nc stdin=nc stdout=nc usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 uImage; if ext2load usb $usb_device 0x1100000 uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 usb_rootfstype=ext4 usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_1=usb=0:1 dev=sda3 usb_scan_2=usb=1:1 dev=sdb3 usb_scan_3=usb=2:1 dev=sdc3 usb_scan_4=usb=3:1 dev=sdd3 Environment size: 2743/131068 bytes
Edited 1 time(s). Last edit at 10/22/2014 09:31AM by rustyspoons.
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 12:14PM |
Admin Registered: 13 years ago Posts: 18,550 |
These needs to be adjusted:
to
because as you said, VAMP likes this better:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd
to
usb_load_uimage=ext2load usb $device 0x800000 /uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /uInitrd
because as you said, VAMP likes this better:
/usr/sbin/fw_setenv usb_boot 'mw 0x800000 0 1; ext2load usb $usb_device 0x800000 uImage; if ext2load usb $usb_device 0x1100000 uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi'
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 12:55PM |
Registered: 9 years ago Posts: 22 |
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 01:45PM |
Registered: 9 years ago Posts: 22 |
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 01:49PM |
Registered: 9 years ago Posts: 22 |
rustyspoons Wrote:
-------------------------------------------------------
> UPDATE,
>
> Re-installed your
> uboot.2014.07-tld-1.environment.img, now entering
> the 2 commands at Uboot console gets it booting
> off VAMP kernel...
>
> Progress is happening!!
Got a Green/Red LED on together and it's hung at starting Kernel.
-------------------------------------------------------
> UPDATE,
>
> Re-installed your
> uboot.2014.07-tld-1.environment.img, now entering
> the 2 commands at Uboot console gets it booting
> off VAMP kernel...
>
> Progress is happening!!
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4
gcc (Debian 4.6.3-14) 4.6.3
GNU ld (GNU Binutils for Debian) 2.22
Hit any key to stop autoboot: 9
0
Pogov4> setenv usb_load_uimage ext2load usb $device 0x800000 /uImage
s e t e n v u s b _ l o a d _ u i m a g e e x t 2 l o a d u s b $ d e v i c e 0 x 8 0 0 0 0 0 / u I m a g e
Pogov4> setenv usb_load_uinitrd ext2load usb $device 0x1100000 /uInitrd
s e t e n v u s b _ l o a d _ u i n i t r d e x t 2 l o a d u s b $ d e v i c e 0 x 1 1 0 0 0 0 0 / u I n i t r d
Pogov4> boot
b o o t
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
3604400 bytes read in 380 ms (9 MiB/s)
15522922 bytes read in 1452 ms (10.2 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: 3.9.4-200.fc18.armv5tel.kirkwood
Created: 2013-06-04 19:13:51 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3604336 Bytes = 3.4 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs
Created: 2013-06-04 19:13:52 UTC
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 15522858 Bytes = 14.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Got a Green/Red LED on together and it's hung at starting Kernel.
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 02:18PM |
Registered: 9 years ago Posts: 70 |
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 02:20PM |
Registered: 9 years ago Posts: 22 |
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 02:31PM |
Registered: 9 years ago Posts: 70 |
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 02:38PM |
Registered: 9 years ago Posts: 22 |
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4
SoC: Kirkwood 88F6192_A1
DRAM: 128 MiB
WARNING: Caches not enabled
NAND: 128 MiB
MMC: kwsdio: 0
In: serial
Out: serial
Err: serial
Net: egiga0
No link on egiga0
ping failed; host 192.168.1.100 is not alive
Hit any key to stop autoboot: 0
Pogov4> setenv usb_load_uimage ext2load usb $device 0x800000 /uImage
Pogov4> setenv usb_load_uinitrd ext2load usb $device 0x1100000 /uInitrd
Pogov4> boot
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
3604400 bytes read in 417 ms (8.2 MiB/s)
15522922 bytes read in 1610 ms (9.2 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: 3.9.4-200.fc18.armv5tel.kirkwood
Created: 2013-06-04 19:13:51 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3604336 Bytes = 3.4 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs
Created: 2013-06-04 19:13:52 UTC
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 15522858 Bytes = 14.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Using machid 0xf78 from environment
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Serial console, and hung :(
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 02:54PM |
Registered: 9 years ago Posts: 22 |
Current NAND env (without me overiding) Of My V4
Pogov4> printenv arcNumber=3960 baudrate=115200 bootargs=console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 ethaddr=00:25:31:05:2a:77 if_netconsole=ping $serverip ipaddr=192.168.1.10 led_error=orange blinking led_exit=green off led_init=green blinking machid=F78 mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot=run if_netconsole start_netconsole preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext3 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 serverip=192.168.1.100 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 usb_rootfstype=ext3
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 03:06PM |
Registered: 9 years ago Posts: 22 |
Booting....
setenv machid
setenv archnumber
Now get as far as....
setenv machid
setenv archnumber
Now get as far as....
[ 20.602809] scsi 0:0:0:0: Direct-Access Lexar USB Flash Drive 8.07 PQ: 0 ANSI: 4 [ 20.616490] sd 0:0:0:0: [sda] 15659008 512-byte logical blocks: (8.01 GB/7.46 GiB) [ 20.626105] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 20.637734] sd 0:0:0:0: [sda] Write Protect is off [ 20.649733] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 20.670941] sda: sda1 sda2 sda3 [ 20.684355] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 21.189022] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 21.203459] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null) dracut-initqueue[133]: Warning: e2fsck returned with 1 [ 24.479397] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 25.032156] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null) dracut-initqueue[133]: Warning: /sysroot has no proper rootfs layout, ignoring and removing offending mount hook dracut-initqueue[133]: Warning: Can't mount root filesystem [ OK ] Started Show Plymouth Boot Screen. [ OK ] Reached target Basic System. dracut-initqueue[133]: Warning: e2fsck returned with 1 dracut-initqueue[133]: Warning: /sysroot has no proper rootfs layout, ignoring and removing offending mount hook dracut-initqueue[133]: Warning: Can't mount root filesystem Entering emergency mode. Exit the shell to continue. Type "journalctl" to view system logs. dracut:/#
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 04:44PM |
Admin Registered: 13 years ago Posts: 18,550 |
Make sure your u-boot env rootfstype matches what fs you have on the USB drive (ext2,3,4).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 04:47PM |
Registered: 9 years ago Posts: 22 |
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 22, 2014 08:40PM |
Admin Registered: 13 years ago Posts: 18,550 |
rustyspoons Wrote:
-------------------------------------------------------
> bodhi Wrote:
> --------------------------------------------------
> -----
> > Make sure your u-boot env rootfstype matches
> what
> > fs you have on the USB drive (ext2,3,4).
>
> I've tried ext4 but still the same.
Your dmesg showed that the kernel thinks the VAMP rootfs is Ext2.
- Does the rootfs labeled "rootfs"?
- what is the content of fstab?
- what are the ouput of:
ls -l /
ls -l /boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> bodhi Wrote:
> --------------------------------------------------
> -----
> > Make sure your u-boot env rootfstype matches
> what
> > fs you have on the USB drive (ext2,3,4).
>
> I've tried ext4 but still the same.
Your dmesg showed that the kernel thinks the VAMP rootfs is Ext2.
- Does the rootfs labeled "rootfs"?
- what is the content of fstab?
- what are the ouput of:
ls -l /
ls -l /boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 23, 2014 07:52AM |
Registered: 9 years ago Posts: 22 |
bodhi Wrote:
-------------------------------------------------------
> rustyspoons Wrote:
> --------------------------------------------------
> -----
> > bodhi Wrote:
> >
> --------------------------------------------------
>
> > -----
> > > Make sure your u-boot env rootfstype matches
> > what
> > > fs you have on the USB drive (ext2,3,4).
> >
> > I've tried ext4 but still the same.
>
> Your dmesg showed that the kernel thinks the VAMP
> rootfs is Ext2.
>
> - Does the rootfs labeled "rootfs"? - Yes
> - what is the content of fstab?
> - what are the ouput of:
> ls -l /
> ls -l /boot
I see dmesg mention that, but in the original VAMP script to set the envs it states rootfs as ext4?,
I will fire this image up on a serial attached E02 and check some things, I think there is a slight difference somewhere with your UBoot env's and Jeff's UBoot envs?
Yes it's labled "rootfs"
rootfs
boot
/etc/fstab
Thanks Bodhi,
Dale
-------------------------------------------------------
> rustyspoons Wrote:
> --------------------------------------------------
> -----
> > bodhi Wrote:
> >
> --------------------------------------------------
>
> > -----
> > > Make sure your u-boot env rootfstype matches
> > what
> > > fs you have on the USB drive (ext2,3,4).
> >
> > I've tried ext4 but still the same.
>
> Your dmesg showed that the kernel thinks the VAMP
> rootfs is Ext2.
>
> - Does the rootfs labeled "rootfs"? - Yes
> - what is the content of fstab?
> - what are the ouput of:
> ls -l /
> ls -l /boot
I see dmesg mention that, but in the original VAMP script to set the envs it states rootfs as ext4?,
I will fire this image up on a serial attached E02 and check some things, I think there is a slight difference somewhere with your UBoot env's and Jeff's UBoot envs?
Yes it's labled "rootfs"
rootfs
dale@HP7800:/media/dale/rootfs$ ls -l total 76 lrwxrwxrwx. 1 root root 7 Feb 2 2013 bin -> usr/bin drwxr-xr-x. 2 root root 4096 Feb 2 2013 boot drwxr-xr-x. 2 root root 4096 Feb 2 2013 dev drwxr-xr-x. 91 root root 4096 Oct 22 20:55 etc drwxr-xr-x. 2 root root 4096 Jul 23 2012 home lrwxrwxrwx. 1 root root 7 Feb 2 2013 lib -> usr/lib drwx------. 2 root root 16384 Feb 2 2013 lost+found drwxr-xr-x. 2 root root 4096 Jul 23 2012 media drwxr-xr-x. 2 root root 4096 Jul 23 2012 mnt drwxr-xr-x. 3 root root 4096 May 21 2013 opt drwxr-xr-x 2 root root 4096 Feb 2 2013 proc dr-xr-x---. 3 root root 4096 Apr 24 2013 root drwxr-xr-x. 14 root root 4096 Feb 2 2013 run lrwxrwxrwx. 1 root root 8 Feb 2 2013 sbin -> usr/sbin drwxr-xr-x. 2 root root 4096 Jul 23 2012 srv drwxr-xr-x. 2 root root 4096 Feb 2 2013 sys drwxrwxrwt. 2 root root 4096 Feb 2 2013 tmp drwxr-xr-x. 12 root root 4096 Feb 2 2013 usr drwxr-xr-x. 19 root root 4096 Apr 24 2013 var
boot
dale@HP7800:/media/dale/borootfsot$ ls -l total 58265 -rw-r--r-- 1 root root 195 Feb 2 2013 boot.cmd.mmc -rw-r--r-- 1 root root 195 Feb 2 2013 boot.cmd.usb -rw-r--r-- 1 root root 267 Feb 2 2013 boot.scr -rw-r--r-- 1 root root 267 Feb 2 2013 boot.scr.mmc -rw-r--r-- 1 root root 267 Feb 2 2013 boot.scr.usb -rw-r--r-- 1 root root 120709 May 26 2013 config-3.9.4-200.fc18.armv5tel.kirkwood drwxr-xr-x 2 root root 1024 Jun 4 2013 dtb-3.9.4-200.fc18.armv5tel.kirkwood drwxr-xr-x 3 root root 1024 Feb 2 2013 grub2 -rw------- 1 root root 15522858 Jun 4 2013 initramfs-3.9.4-200.fc18.armv5tel.kirkwood.img -rw-r--r-- 1 root root 242272 Feb 2 2013 initrd-plymouth.img -rw------- 1 root root 33 Jun 4 2013 klist.txt drwx------. 2 root root 12288 Feb 2 2013 lost+found -rw------- 1 root root 1649327 May 26 2013 System.map-3.9.4-200.fc18.armv5tel.kirkwood -rw-r--r-- 1 root root 3604400 Jun 4 2013 uImage -rw-r--r-- 1 root root 3604400 Jun 4 2013 uImage-3.9.4-200.fc18.armv5tel.kirkwood -rw-r--r-- 1 root root 15522922 Jun 4 2013 uInitrd -rw-r--r-- 1 root root 15522922 Jun 4 2013 uInitrd-3.9.4-200.fc18.armv5tel.kirkwood -rwxr-xr-x 1 root root 3604336 May 26 2013 vmlinuz-3.9.4-200.fc18.armv5tel.kirkwood
/etc/fstab
# # /etc/fstab # Created by anaconda on Fri Feb 1 23:08:47 2013 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # UUID=997e9b52-62a6-4273-9427-ffe2c16ac534 / ext4 defaults 1 1 UUID=c5755968-e771-4898-a876-3af2fc0cdfc3 /boot ext2 defaults 1 2 UUID=798c08db-e355-4bad-b721-59f0c7656465 swap swap defaults 0 0
Thanks Bodhi,
Dale
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 23, 2014 01:41PM |
Registered: 9 years ago Posts: 22 |
Thought this might help
Pogoplug E02 with VAMP, Working uBOOT Env
Edited 2 time(s). Last edit at 10/23/2014 01:46PM by rustyspoons.
Pogoplug E02 with VAMP, Working uBOOT Env
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
u-boot>> printenv arcNumber=2097 baudrate=115200 bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset bootdelay=3 console=ttyS0,115200 ethact=egiga0 ethaddr=00:25:31:00:51:EE force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params stderr=serial stdin=serial stdout=serial ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 uImage; if ext2load usb $usb_device 0x1100000 uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_device=0:1 usb_init=run usb_scan usb_root=/dev/sda1 usb_rootdelay=10 usb_rootfstype=ext4 usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_1=usb=0:1 dev=sda3 usb_scan_2=usb=1:1 dev=sdb3 usb_scan_3=usb=2:1 dev=sdc3 usb_scan_4=usb=3:1 dev=sdd3 usb_scan_list=1 2 3 4 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
Edited 2 time(s). Last edit at 10/23/2014 01:46PM by rustyspoons.
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 23, 2014 04:10PM |
Admin Registered: 13 years ago Posts: 18,550 |
@Dale,
The new u-boot is a drop-in replacement for davygravy's u-boot, which is what you have installed on Pogo E02. All envs are reusable as they are. Of course, each machine needs a different u-boot binary, but the code is common. As for kernel, I suspect there might be a different issue lurking, but you have not got to that point yet! Currently you are still at the rootfs mounting stage.
If this rootfs partition is labeled "rootfs" (not the /boot partition)
Then use the rootfs partition label approach. Base on your current env for the Pogo V4 above, you can do this:
In serial console:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
The new u-boot is a drop-in replacement for davygravy's u-boot, which is what you have installed on Pogo E02. All envs are reusable as they are. Of course, each machine needs a different u-boot binary, but the code is common. As for kernel, I suspect there might be a different issue lurking, but you have not got to that point yet! Currently you are still at the rootfs mounting stage.
If this rootfs partition is labeled "rootfs" (not the /boot partition)
UUID=997e9b52-62a6-4273-9427-ffe2c16ac534 / ext4 defaults 1 1
Then use the rootfs partition label approach. Base on your current env for the Pogo V4 above, you can do this:
In serial console:
setenv usb_root 'LABEL=rootfs'And then go ahead, boot. If you can't boot, then please repost the envs. If you boot into VAMP or got stuck somewhere, then post the entire serial console log.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 23, 2014 05:40PM |
Registered: 9 years ago Posts: 22 |
Bodhi,
It's working :D
Few little tweaks and I'll make a script to install the env's, amazing, boots quicker than E02 and playing music right now :D :D, thanks for your assistance :D
It's working :D
Few little tweaks and I'll make a script to install the env's, amazing, boots quicker than E02 and playing music right now :D :D, thanks for your assistance :D
Fedora release 18 (Spherical Cow) Kernel 3.9.4-200.fc18.armv5tel.kirkwood on an armv5tel (ttyS0) localhost login: root Password: [root@localhost ~]# [ 174.858681] usb 2-1: new full-speed USB device number 2 using xhci_hcd [ 174.880098] usb 2-1: New USB device found, idVendor=08bb, idProduct=2704 [ 174.886784] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 174.893933] usb 2-1: Product: USB Audio DAC [ 174.898359] usb 2-1: Manufacturer: Burr-Brown from TI [ 174.905311] usb 2-1: ep 0x85 - rounding interval to 64 microframes, ep desc says 80 microframes
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 23, 2014 06:35PM |
Admin Registered: 13 years ago Posts: 18,550 |
Awesome :)
Yes, please post your script, or instruction here so others looking for installing VAMP or just Fedora can find it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Yes, please post your script, or instruction here so others looking for installing VAMP or just Fedora can find it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 24, 2014 04:21AM |
Registered: 9 years ago Posts: 22 |
|
Re: U-Boot VAMP 0.6 Pogoplug V4 October 24, 2014 05:11AM |
Admin Registered: 13 years ago Posts: 18,550 |
Dale,
Please post these:
I want to see if the kernel identifies the box as Pogo V4. If not then the LEDs can not be controlled correctly. However, there might be a work around if we can take a look at (where is the Git) the source tree used to build the Fedora kernel.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 10/24/2014 05:13AM by bodhi.
Please post these:
dmesg cat /proc/cpuinfo ls /sys/class/leds/ -l
I want to see if the kernel identifies the box as Pogo V4. If not then the LEDs can not be controlled correctly. However, there might be a work around if we can take a look at (where is the Git) the source tree used to build the Fedora kernel.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 10/24/2014 05:13AM by bodhi.
