How do I get out of my Pogoplug Mobile rathole? February 26, 2017 06:06PM |
Registered: 7 years ago Posts: 4 |
Re: How do I get out of my Pogoplug Mobile rathole? February 26, 2017 06:42PM |
Admin Registered: 13 years ago Posts: 18,570 |
Quote
I currently have access to my Plug through a soldered cable. It has U-Boot v 2016.05-tld-1 for Pogoplug V4 installed, but will not boot from either my new USB stick (SanDisk 16GB) or my SD Card (SanDisk 16 GB), most likely due in a large part to the environment variables. I have a Raspberry Pi running Arch that I can use to play with my USB stick and SD Card.
printenv boot
Re: How do I get out of my Pogoplug Mobile rathole? February 26, 2017 06:50PM |
Registered: 7 years ago Posts: 4 |
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 3 2 0 Pogov4> printenv arcNumber=3960 bootargs=root=/dev/nfs nfsroot=192.168.0.220: ip=192.168.0.231:192.168.0.220:::::off bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=3 bootdev=usb device=0:1 devices=usb mmc ide disks=0 1 2 3 ethact=egiga0 ethaddr=00:25:31:05:b8:e4 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=f78 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 2901/131068 bytes Pogov4> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: ide_preinit failed Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 30210048 63754a41-01 83 Boot 2 30212096 1048576 63754a41-02 82 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** no IDE devices available running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 134 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 4604848 bytes read in 309 ms (14.2 MiB/s) loading uInitrd ... ** File not found /boot/uInitrd ** loading DTB ... ** No boot file defined ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.4.45-1-ARCH Created: 2017-01-29 5:31:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4604784 Bytes = 4.4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK Using machid 0xf78 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.45-1-ARCH (builduser@leming) (gcc version 6.3.1 20170109 (GCC) ) #1 PREEMPT Sat Jan 28 22:31:00 MST 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Pogoplug V4 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 119688K/131072K available (6606K kernel code, 547K rwdata, 1876K rodata, 300K init, 725K bss, 11384K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc08509e4 (8483 kB) [ 0.000000] .init : 0xc0851000 - 0xc089c000 ( 300 kB) [ 0.000000] .data : 0xc089c000 - 0xc0924e6c ( 548 kB) [ 0.000000] .bss : 0xc0924e6c - 0xc09da438 ( 726 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:114 [ 0.000021] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 24.811464] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 24.811749] Console: colour dummy device 80x30 [ 24.811794] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216) [ 24.901572] pid_max: default: 32768 minimum: 301 [ 24.901711] Security Framework initialized [ 24.901824] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 24.901853] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 24.902975] Initializing cgroup subsys io [ 24.903027] Initializing cgroup subsys memory [ 24.903107] Initializing cgroup subsys devices [ 24.903147] Initializing cgroup subsys freezer [ 24.903179] Initializing cgroup subsys net_cls [ 24.903208] Initializing cgroup subsys perf_event [ 24.903243] Initializing cgroup subsys net_prio [ 24.903369] CPU: Testing write buffer coherency: ok [ 24.904057] Setting up static identity map for 0x81e0 - 0x8238 [ 24.906998] devtmpfs: initialized [ 24.910601] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 24.911342] pinctrl core: initialized pinctrl subsystem [ 24.912588] NET: Registered protocol family 16 [ 24.913344] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 24.941602] cpuidle: using governor ladder [ 24.971604] cpuidle: using governor menu [ 24.971852] Kirkwood: MV88F6281-A1, TCLK=166666667. [ 24.971890] Feroceon L2: Enabling L2 [ 24.971942] Feroceon L2: Cache support initialised. [ 24.975353] Kirkwood PCIe port 0: link down [ 24.975369] PCI: bus0 uses PCIe port 0 [ 24.975715] PCI host bridge to bus 0000:00 [ 24.975741] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 24.975758] pci_bus 0000:00: root bus resource [io 0x1000-0xffff] [ 24.975774] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 24.976304] PCI: bus0: Fast back to back transfers disabled [ 25.013755] vgaarb: loaded [ 25.014219] SCSI subsystem initialized [ 25.014948] usbcore: registered new interface driver usbfs [ 25.015061] usbcore: registered new interface driver hub [ 25.015147] usbcore: registered new device driver usb [ 25.015399] pps_core: LinuxPPS API ver. 1 registered [ 25.015412] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 25.015463] PTP clock support registered [ 25.017067] clocksource: Switched to clocksource orion_clocksource [ 25.074325] FS-Cache: Loaded [ 25.093375] NET: Registered protocol family 2 [ 25.094551] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 25.094590] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 25.094620] TCP: Hash tables configured (established 1024 bind 1024) [ 25.094727] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 25.094764] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 25.095037] NET: Registered protocol family 1 [ 25.095510] RPC: Registered named UNIX socket transport module. [ 25.095526] RPC: Registered udp transport module. [ 25.095536] RPC: Registered tcp transport module. [ 25.095546] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 25.098586] futex hash table entries: 256 (order: -1, 3072 bytes) [ 25.117715] VFS: Disk quotas dquot_6.6.0 [ 25.118115] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 25.121130] FS-Cache: Netfs 'nfs' registered for caching [ 25.122812] NFS: Registering the id_resolver key type [ 25.122905] Key type id_resolver registered [ 25.122918] Key type id_legacy registered [ 25.123042] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 25.124991] fuse init (API version 7.23) [ 25.128268] aufs 4.4-20170130 [ 25.135844] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 25.135880] io scheduler noop registered [ 25.135902] io scheduler deadline registered [ 25.136296] io scheduler cfq registered [ 25.136690] io scheduler bfq registered (default) [ 25.136702] BFQ I/O-scheduler: v7r11 [ 25.136998] mv_xor mv_xor.0: Marvell shared XOR driver [ 25.179011] mv_xor mv_xor.0: Marvell XOR (Registers Mode): ( xor cpy ) [ 25.179369] mv_xor mv_xor.1: Marvell shared XOR driver [ 25.218922] mv_xor mv_xor.1: Marvell XOR (Registers Mode): ( xor cpy ) [ 25.227179] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 25.228738] console [ttyS0] disabled [ 25.248824] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A [ 25.837206] console [ttyS0] enabled [ 25.864222] brd: module loaded [ 25.878801] loop: module loaded [ 25.882446] sata_mv sata_mv.0: cannot get optional clkdev [ 25.888013] sata_mv sata_mv.0: slots 32 ports 1 [ 25.895015] scsi host0: sata_mv [ 25.898749] ata1: SATA max UDMA/133 irq 21 [ 25.903868] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 25.910395] nand: Hynix H27U1G8F2BTR-BC [ 25.914221] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 25.921804] Scanning device for bad blocks [ 25.969648] Bad eraseblock 533 at 0x0000042a0000 [ 25.989206] Bad eraseblock 716 at 0x000005980000 [ 26.018966] 4 cmdlinepart partitions found on MTD device orion_nand [ 26.025207] Creating 4 MTD partitions on "orion_nand": [ 26.030354] 0x000000000000-0x000000100000 : "u-boot" [ 26.036030] 0x000000100000-0x000000500000 : "uImage" [ 26.041669] 0x000000500000-0x000002500000 : "rootfs" [ 26.047366] 0x000002500000-0x000008000000 : "data" [ 26.062657] libphy: orion_mdio_bus: probed [ 26.066901] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 26.257111] ata1: SATA link down (SStatus 0 SControl F300) [ 27.151511] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:b8:e4 [ 27.160450] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 27.166958] ehci-pci: EHCI PCI platform driver [ 27.171521] ehci-orion: EHCI orion driver [ 27.175627] orion-ehci orion-ehci.0: EHCI Host Controller [ 27.181073] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 27.188845] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 27.207118] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 27.214508] hub 1-0:1.0: USB hub found [ 27.218366] hub 1-0:1.0: 1 port detected [ 27.223365] usbcore: registered new interface driver uas [ 27.228924] usbcore: registered new interface driver usb-storage [ 27.234990] usbcore: registered new interface driver ums-alauda [ 27.241021] usbcore: registered new interface driver ums-cypress [ 27.247115] usbcore: registered new interface driver ums-datafab [ 27.253174] usbcore: registered new interface driver ums_eneub6250 [ 27.259432] usbcore: registered new interface driver ums-freecom [ 27.265485] usbcore: registered new interface driver ums-isd200 [ 27.271482] usbcore: registered new interface driver ums-jumpshot [ 27.277659] usbcore: registered new interface driver ums-karma [ 27.283543] usbcore: registered new interface driver ums-onetouch [ 27.289744] usbcore: registered new interface driver ums-realtek [ 27.295803] usbcore: registered new interface driver ums-sddr09 [ 27.301802] usbcore: registered new interface driver ums-sddr55 [ 27.307797] usbcore: registered new interface driver ums-usbat [ 27.314239] mousedev: PS/2 mouse device common for all mice [ 27.537107] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 27.689755] usb-storage 1-1:1.0: USB Mass Storage device detected [ 27.696260] scsi host1: usb-storage 1-1:1.0 [ 28.327105] rtc-mv rtc-mv: internal RTC not ticking [ 28.332179] i2c /dev entries driver [ 28.336555] sdhci: Secure Digital Host Controller Interface driver [ 28.342750] sdhci: Copyright(c) Pierre Ossman [ 28.387413] sdhci-pltfm: SDHCI platform and OF driver helper [ 28.396925] ledtrig-cpu: registered to indicate activity on CPUs [ 28.403177] usbcore: registered new interface driver r8712u [ 28.409190] gre: GRE over IPv4 demultiplexor driver [ 28.414150] NET: Registered protocol family 17 [ 28.418838] Key type dns_resolver registered [ 28.425705] registered taskstats version 1 [ 28.432447] Key type encrypted registered [ 28.437399] console [netcon0] enabled [ 28.441055] netconsole: network logging started [ 28.446171] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 28.453370] hctosys: unable to open rtc device (rtc0) [ 28.463307] Waiting 10 sec before mounting root device... [ 28.698369] scsi 1:0:0:0: Direct-Access SanDisk Cruzer Fit 1.00 PQ: 0 ANSI: 6 [ 28.708413] sd 1:0:0:0: [sda] 31260672 512-byte logical blocks: (16.0 GB/14.9 GiB) [ 28.716303] sd 1:0:0:0: Attached scsi generic sg0 type 0 [ 28.722210] sd 1:0:0:0: [sda] Write Protect is off [ 28.728408] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 28.744762] sda: sda1 sda2 [ 28.751773] sd 1:0:0:0: [sda] Attached SCSI removable disk [ 38.477451] VFS: Cannot open root device "LABEL=rootfs" or unknown-block(0,0): error -6 [ 38.485427] Please append a correct "root=" boot option; here are the available partitions: [ 38.493864] 0100 8192 ram0 (driver?) [ 38.498542] 0101 8192 ram1 (driver?) [ 38.503152] 0102 8192 ram2 (driver?) [ 38.507812] 0103 8192 ram3 (driver?) [ 38.512423] 0104 8192 ram4 (driver?) [ 38.517027] 0105 8192 ram5 (driver?) [ 38.521688] 0106 8192 ram6 (driver?) [ 38.526298] 0107 8192 ram7 (driver?) [ 38.530932] 0108 8192 ram8 (driver?) [ 38.535543] 0109 8192 ram9 (driver?) [ 38.540168] 010a 8192 ram10 (driver?) [ 38.544866] 010b 8192 ram11 (driver?) [ 38.549577] 010c 8192 ram12 (driver?) [ 38.554275] 010d 8192 ram13 (driver?) [ 38.558993] 010e 8192 ram14 (driver?) [ 38.563692] 010f 8192 ram15 (driver?) [ 38.568408] 0800 15630336 sda driver: sd [ 38.573015] 0801 15105024 sda1 63754a41-01 [ 38.577898] 0802 524288 sda2 63754a41-02 [ 38.582761] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 38.590996] CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.45-1-ARCH #1 [ 38.597322] Hardware name: Pogoplug V4 [ 38.601094] [<c0010524>] (unwind_backtrace) from [<c000d9d0>] (show_stack+0x10/0x14) [ 38.608820] [<c000d9d0>] (show_stack) from [<c00cda50>] (panic+0x88/0x208) [ 38.615678] [<c00cda50>] (panic) from [<c08522c8>] (mount_block_root+0x1a0/0x260) [ 38.623131] [<c08522c8>] (mount_block_root) from [<c0852578>] (mount_root+0xf4/0x120) [ 38.630931] [<c0852578>] (mount_root) from [<c0852700>] (prepare_namespace+0x15c/0x1bc) [ 38.638906] [<c0852700>] (prepare_namespace) from [<c0851eb4>] (kernel_init_freeable+0x1fc/0x254) [ 38.647756] [<c0851eb4>] (kernel_init_freeable) from [<c0648c7c>] (kernel_init+0x8/0xe8) [ 38.655817] [<c0648c7c>] (kernel_init) from [<c000a4d0>] (ret_from_fork+0x14/0x24) [ 38.663361] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Re: How do I get out of my Pogoplug Mobile rathole? February 26, 2017 11:53PM |
Admin Registered: 13 years ago Posts: 18,570 |
> U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700) > Pogoplug V4 > [ 0.000000] Linux version 4.4.45-1-ARCH (buildu > ser@leming) (gcc version 6.3.1 20170109 (GCC) ) #1 > PREEMPT Sat Jan 28 22:31:00 MST 2017 > [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
Quote
Updated 20 Feb 2016:
This Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 is to keep in sync with kernel Linux-4.4.0-kirkwood-tld-1.
setenv dtb_file '/boot/dts/kirkwood-pogoplug_v4.dtb'
printenv boot
Re: How do I get out of my Pogoplug Mobile rathole? March 04, 2017 09:22PM |
Registered: 7 years ago Posts: 4 |
dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb devices=usb devices=mmc usb ide disks=0 1 2 3 4 5 6 7
[ 0.171429] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[ 1.285998] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 36 [ 1.286022] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 37 [ 1.286040] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 38 [ 1.286058] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 39 [ 1.286076] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 40 [ 1.286093] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 41 [ 1.286110] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 42 [ 1.286128] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 43 [ 1.286145] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 44 [ 1.286163] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 45 [ 1.286180] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 46 [ 1.286198] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47 [ 1.286215] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 48 [ 1.286233] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49
Warning: File system check failed but did not detect errors [ 20.769718] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 20.788923] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done.
[ 24.863264] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
root@debian:~# fdisk -l /dev/sda Disk /dev/sda: 14.9 GiB, 16005464064 bytes, 31260672 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x95537bd3 Device Boot Start End Sectors Size Id Type /dev/sda1 * 2048 31260671 31258624 14.9G 83 Linux root@debian:~# cat /etc/fstab # /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> /dev/root / ext2 noatime,errors=remount-ro 0 1 tmpfs /tmp tmpfs defaults 0 0 root@debian:~#A screen capture with my reboot, interupt, print env vars, boot, and login is attached as a file. I think I hit some limit with the size of this post and could not embed it.
Re: How do I get out of my Pogoplug Mobile rathole? March 04, 2017 10:26PM |
Admin Registered: 13 years ago Posts: 18,570 |
mountexpected output
/dev/sda1 on / type ext3 (rw,noatime,errors=remount-ro,data=ordered)
devices=usb ide
/dev/sda1 on / type ext3 (rw,noatime,errors=remount-ro,data=ordered)