goflex net problems with uboot January 14, 2011 03:35AM |
Registered: 13 years ago Posts: 25 |
U-Boot 2010.09 (Oct 23 2010 - 11:53:10) Marvell-GoflexNet by Jeff Doozan, Peter Carmichael SoC: Kirkwood 88F6281_A0 DRAM: 128 MiB NAND: 256 MiB In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Block device usb 0 not supported ** Invalid boot device ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000010000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 219 MiB UBI: number of good PEBs: 1751 UBI: number of bad PEBs: 1 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 1730 UBI: total number of reserved PEBs: 21 UBI: number of PEBs reserved for bad PEB handling: 17 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! ** Block device usb 0 not supported ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported ** Block device usb 0 not supported ** Block device usb 0 not supported Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: ........ done. ### JFFS2 load complete: 524288 bytes loaded to 0x800000 ## Starting application at 0x00800200 ...
Marvell>> tftp 0x800000 uboot.mtd0.dockstar.original.kwb Using egiga0 device TFTP from server 192.168.1.1; our IP address is 192.168.1.100 Filename 'uboot.mtd0.dockstar.original.kwb'. Load address: 0x800000 Loading: ################################################################# ###################################### done Bytes transferred = 524288 (80000 hex) Marvell>> go 0x800200 ## Starting application at 0x00800200 ... U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: MV88F6281 Rev 3 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: DISCOVERY:0.1 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 CE>>
-sh-3.2# fw_printenv [ 26.710000] JFFS2 compression type 0x07 not available. [ 26.720000] Error: jffs2_decompress returned -5 ...
Re: goflex net problems with uboot May 30, 2011 12:05PM |
Registered: 12 years ago Posts: 6 |
Re: goflex net problems with uboot May 30, 2011 02:11PM |
Registered: 13 years ago Posts: 25 |