Is uBoot OS specific?
Posted by balanga
|
Is uBoot OS specific? June 14, 2017 05:25PM |
Registered: 7 years ago Posts: 337 |
I don'know anything about uBoot, and I'm not sure if my understanding of it as a Universal boot loader for embedded ARM systems is correct. If that is the case, then presumably the same uBoot can load any OS which works on the platform, not just Debian, but also ArchLinux and even (God forbid) Windows.
Is my understanding correct?
Is my understanding correct?
|
Re: Is uBoot OS specific? June 14, 2017 05:34PM |
Admin Registered: 14 years ago Posts: 19,558 |
balanga Wrote:
-------------------------------------------------------
> I don'know anything about uBoot, and I'm not sure
> if my understanding of it as a Universal boot load
> er for embedded ARM systems is correct. If that is
> the case, then presumably the same uBoot can load
> any OS which works on the platform, not just Debia
> n, but also ArchLinux and even (God forbid) Window
> s.
>
> Is my understanding correct?
u-boot will load and run virtually all Linux distros (Debian, Arch, Gentoo, Fedora ....). But not Windows.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> I don'know anything about uBoot, and I'm not sure
> if my understanding of it as a Universal boot load
> er for embedded ARM systems is correct. If that is
> the case, then presumably the same uBoot can load
> any OS which works on the platform, not just Debia
> n, but also ArchLinux and even (God forbid) Window
> s.
>
> Is my understanding correct?
u-boot will load and run virtually all Linux distros (Debian, Arch, Gentoo, Fedora ....). But not Windows.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Is uBoot OS specific? June 15, 2017 08:53AM |
Registered: 7 years ago Posts: 337 |
|
Re: Is uBoot OS specific? June 15, 2017 11:17AM |
Registered: 8 years ago Posts: 310 |
|
Re: Is uBoot OS specific? June 16, 2017 04:38PM |
Registered: 7 years ago Posts: 337 |
|
Re: Is uBoot OS specific? June 16, 2017 04:49PM |
Admin Registered: 14 years ago Posts: 19,558 |
balanga Wrote:
-------------------------------------------------------
> Is there such a thing as a FreeBSD uBoot?
No. U-Boot is not OS specific. How you configure envs settings to boot certain distro is what make it specific.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> Is there such a thing as a FreeBSD uBoot?
No. U-Boot is not OS specific. How you configure envs settings to boot certain distro is what make it specific.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Is uBoot OS specific? June 19, 2017 10:30PM |
Registered: 7 years ago Posts: 337 |
|
Re: Is uBoot OS specific? June 19, 2017 10:51PM |
Registered: 8 years ago Posts: 310 |
balanga Wrote:
-------------------------------------------------------
> feas Wrote:
> --------------------------------------------------
> -----
> > yep
>
yep was a simple answer to your question if u-boot would allow other OS's to load.
>
> Does this mean you have or know someone who has Fr
> eeBSD working on a GoFlex Home unit?
For this question a simple google search came up with this but I can't speak of it from experience.
https://cooltrainer.org/freebsd-kirkwood/building/
-------------------------------------------------------
> feas Wrote:
> --------------------------------------------------
> -----
> > yep
>
yep was a simple answer to your question if u-boot would allow other OS's to load.
>
> Does this mean you have or know someone who has Fr
> eeBSD working on a GoFlex Home unit?
For this question a simple google search came up with this but I can't speak of it from experience.
https://cooltrainer.org/freebsd-kirkwood/building/
|
Re: Is uBoot OS specific? June 20, 2017 12:17AM |
Admin Registered: 14 years ago Posts: 19,558 |
balanga,
feas has covered the rootfs part.
Now the boot loader part is not comlicated. You have installed a new u-boot (mine or Arch does not matter), it will most likely boot FreeBSD rootfs with some simple changes in u-boot envs. But first I need to look at that the FreeBSD rootfs that you will have created, and give you something to try.
With that said, I would prefer that you boot in to Debian rootfs, and then update u-boot with my build so it will save me some time. But if you'd rather keep what you have then it is fine, too.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
feas has covered the rootfs part.
Now the boot loader part is not comlicated. You have installed a new u-boot (mine or Arch does not matter), it will most likely boot FreeBSD rootfs with some simple changes in u-boot envs. But first I need to look at that the FreeBSD rootfs that you will have created, and give you something to try.
With that said, I would prefer that you boot in to Debian rootfs, and then update u-boot with my build so it will save me some time. But if you'd rather keep what you have then it is fine, too.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Is uBoot OS specific? June 20, 2017 02:54AM |
Registered: 7 years ago Posts: 337 |
bodhi Wrote:
-------------------------------------------------------
> balanga,
>
> feas has covered the rootfs part.
>
> Now the boot loader part is not comlicated. You ha
> ve installed a new u-boot (mine or Arch does not m
> atter), it will most likely boot FreeBSD rootfs wi
> th some simple changes in u-boot envs. But first I
> need to look at that the FreeBSD rootfs that you w
> ill have created, and give you something to try.
>
> With that said, I would prefer that you boot in to
> Debian rootfs, and then update u-boot with my buil
> d so it will save me some time. But if you'd rathe
> r keep what you have then it is fine, too.
I'm more than happy to try. I'm more comfortable with FreeBSD - even have it running on my Raspberry Pi, and the ultimate goal was to have a FreeBSD based GoFlex Home unit. So tell me what I need to do and I'll give it a try.
-------------------------------------------------------
> balanga,
>
> feas has covered the rootfs part.
>
> Now the boot loader part is not comlicated. You ha
> ve installed a new u-boot (mine or Arch does not m
> atter), it will most likely boot FreeBSD rootfs wi
> th some simple changes in u-boot envs. But first I
> need to look at that the FreeBSD rootfs that you w
> ill have created, and give you something to try.
>
> With that said, I would prefer that you boot in to
> Debian rootfs, and then update u-boot with my buil
> d so it will save me some time. But if you'd rathe
> r keep what you have then it is fine, too.
I'm more than happy to try. I'm more comfortable with FreeBSD - even have it running on my Raspberry Pi, and the ultimate goal was to have a FreeBSD based GoFlex Home unit. So tell me what I need to do and I'll give it a try.
|
Re: Is uBoot OS specific? June 20, 2017 03:04AM |
Admin Registered: 14 years ago Posts: 19,558 |
balanga,
> So tell me what I need to do
> and I'll give it a try.
As I said, I need to look at that the FreeBSD rootfs that you have and give you something to try (I don't know what it looks like).
On the system that you have FreeBSD running,
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> So tell me what I need to do
> and I'll give it a try.
As I said, I need to look at that the FreeBSD rootfs that you have and give you something to try (I don't know what it looks like).
On the system that you have FreeBSD running,
dmesg ls -l / ls -lart /boot ls -l /lib/modules
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Is uBoot OS specific? June 20, 2017 07:24AM |
Registered: 7 years ago Posts: 337 |
dmesg
ls -l /
ls -lart /boot
gpart show (equivalent to fdisk)
This is from FreeBSD running on a Raspeberry Pi booted from a 32GB MicroSDHC card. There was no such directory as /lib/modules. Maybe what you want is called something else on FreeBSD. This will give you the layout of the filesystem on FreeBSD. Any applications which are not part of the core OS are installed under /usr/local
https://www.freebsd.org/cgi/man.cgi?hier(7)
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2016 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.0-CURRENT #0 r310476: Fri Dec 23 08:20:46 MST 2016
brd@hive.raspbsd.org:/usr/local/raspbsd/obj/RPI2/obj/arm.armv6/usr/local/raspbsd/src/common/sys/RPI2 arm
FreeBSD clang version 3.9.1 (tags/RELEASE_391/final 289601) (based on LLVM 3.9.1)
WARNING: WITNESS option enabled, expect reduced performance.
VT: init without driver.
CPU: ARM Cortex-A7 r0p5 (ECO: 0x00000000)
CPU Features:
Multiprocessing, Thumb2, Security, Virtualization, Generic Timer, VMSAv7,
PXN, LPAE, Coherent Walk
Optional instructions:
SDIV/UDIV, UMULL, SMULL, SIMD(ext)
LoUU:2 LoC:3 LoUIS:2
Cache level 1:
32KB/64B 4-way data cache WB Read-Alloc Write-Alloc
32KB/32B 2-way instruction cache Read-Alloc
Cache level 2:
512KB/64B 8-way unified cache WB Read-Alloc Write-Alloc
real memory = 989851648 (943 MB)
avail memory = 952913920 (908 MB)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> mem 0x3f000000-0x3fffffff on ofwbus0
local_intc0: <BCM2836 Interrupt Controller> mem 0x40000000-0x400000ff on simplebus0
intc0: <BCM2835 Interrupt Controller> mem 0xb200-0xb3ff irq 4 on simplebus0
generic_timer0: <ARMv7 Generic Timer> irq 0,1,2,3 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 19200000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 19200000 Hz quality 1000
bcmwd0: <BCM2708/2835 Watchdog> mem 0x10001c-0x100027 on simplebus0
gpio0: <BCM2708/2835 GPIO controller> mem 0x200000-0x2000af irq 5,6,7,8 on simplebus0
gpio0: read-only pins: 46,48-53.
gpio0: reserved pins: 48-53.
gpiobus0: <OFW GPIO bus> on gpio0
gpioc0: <GPIO controller> on gpio0
bcmrng0: <Broadcom BCM2835 RNG> mem 0x104000-0x10401f irq 9 on simplebus0
iichb0: <BCM2708/2835 BSC controller> mem 0x205000-0x20501f irq 10 on simplebus0
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
iichb1: <BCM2708/2835 BSC controller> mem 0x804000-0x80401f irq 11 on simplebus0
iicbus1: <OFW I2C bus> on iichb1
iic1: <I2C generic I/O> on iicbus1
spi0: <BCM2708/2835 SPI controller> mem 0x204000-0x20401f irq 12 on simplebus0
spibus0: <OFW SPI bus> on spi0
bcm_dma0: <BCM2835 DMA Controller> mem 0x7000-0x7fff,0xe05000-0xe05fff irq 13,14,15,16,17,18,19,20,21,22,23,24,25 on simplebus0
mbox0: <BCM2835 VideoCore Mailbox> mem 0xb880-0xb8bf irq 26 on simplebus0
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x300000-0x3000ff irq 27 on simplebus0
mmc0: <MMC/SD bus> on sdhci_bcm0
uart0: <PrimeCell UART (PL011)> mem 0x201000-0x201fff irq 28 on simplebus0
uart0: console (115200,n,8,1)
vchiq0: <BCM2835 VCHIQ> mem 0xb800-0xb84f irq 29 on simplebus0
vchiq: local ver 8 (min 3), remote ver 8.
pcm0: <VCHIQ audio> on vchiq0
bcm283x_dwcotg0: <DWC OTG 2.0 integrated USB controller (bcm283x)> mem 0x980000-0x99ffff irq 30 on simplebus0
usbus0 on bcm283x_dwcotg0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
bcm2835_cpufreq0: <CPU Frequency Control> on cpu0
cpu1: <Open Firmware CPU> on cpulist0
cpu2: <Open Firmware CPU> on cpulist0
cpu3: <Open Firmware CPU> on cpulist0
fb0: <BCM2835 VT framebuffer driver> on ofwbus0
fbd0 on fb0
VT: initialize with new VT driver "fb".
fb0: 1280x1024(1280x1024@0,0) 24bpp
fb0: fbswap: 1, pitch 3840, base 0x3d5b9000, screen_size 3932160
gpioled0: <GPIO LEDs> on ofwbus0
cryptosoft0: <software crypto>
Timecounters tick every 1.000 msec
usbus0: 480Mbps High Speed USB v2.0
ugen0.1: <DWCOTG OTG Root HUB> at usbus0
uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
mmcsd0: 32GB <SDHC 00000 1.0 SN A011143E MFG 03/2015 by 27 SM> at mmc0 41.6MHz/4bit/65535-block
bcm2835_cpufreq0: ARM 600MHz, Core 250MHz, SDRAM 400MHz, Turbo OFF
Release APs
WARNING: WITNESS option enabled, expect reduced performance.
Trying to mount root from ufs:/dev/mmcsd0s2a [rw,noatime]...
uhub0: 1 port with 1 removable, self powered
warning: no time-of-day clock registered, system time will not be set accurately
ugen0.2: <vendor 0x0424 product 0x9514> at usbus0
uhub1: <vendor 0x0424 product 0x9514, class 9/0, rev 2.00/2.00, addr 2> on usbus0
uhub1: MTT enabled
uhub1: 5 ports with 4 removable, self powered
ugen0.3: <vendor 0x0424 product 0xec00> at usbus0
smsc0 on uhub1
smsc0: <vendor 0x0424 product 0xec00, rev 2.00/2.00, addr 3> on usbus0
random: unblocking device.
smsc0: chip 0xec00, rev. 0002
miibus0: <MII bus> on smsc0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ue0: <USB Ethernet> on smsc0
ue0: Ethernet address: b8:27:eb:2c:a6:39
ugen0.4: <vendor 0x0000 USB OPTICAL MOUSE> at usbus0
ugen0.5: <NOVATEK USB Keyboard> at usbus0
ukbd0 on uhub1
ukbd0: <NOVATEK USB Keyboard, class 0/0, rev 1.10/1.12, addr 5> on usbus0
kbd1 at ukbd0
smsc0: chip 0xec00, rev. 0002
ue0: link state changed to DOWN
ue0: link state changed to UP
ums0 on uhub1
ums0: <vendor 0x0000 USB OPTICAL MOUSE, class 0/0, rev 1.10/1.00, addr 4> on usbus0
ums0: 3 buttons and [XYZ] coordinates ID=1
uhid0 on uhub1
uhid0: <NOVATEK USB Keyboard, class 0/0, rev 1.10/1.12, addr 5> on usbus0
lock order reversal:
1st 0xd779fdb0 bufwait (bufwait) @ /usr/local/raspbsd/src/common/sys/kern/vfs_bio.c:3512
2nd 0xc47d0400 dirhash (dirhash) @ /usr/local/raspbsd/src/common/sys/ufs/ufs/ufs_dirhash.c:281
stack backtrace:
lock order reversal:
1st 0xc4f96a54 ufs (ufs) @ /usr/local/raspbsd/src/common/sys/kern/vfs_subr.c:2592
2nd 0xd77b5e08 bufwait (bufwait) @ /usr/local/raspbsd/src/common/sys/ufs/ffs/ffs_vnops.c:277
3rd 0xc4ec3a54 ufs (ufs) @ /usr/local/raspbsd/src/common/sys/kern/vfs_subr.c:2592
stack backtrace:
ugen0.5: <NOVATEK USB Keyboard> at usbus0 (disconnected)
ukbd0: at uhub1, port 3, addr 5 (disconnected)
ukbd0: detached
uhid0: at uhub1, port 3, addr 5 (disconnected)
uhid0: detached
ugen0.4: <vendor 0x0000 USB OPTICAL MOUSE> at usbus0 (disconnected)
ums0: at uhub1, port 2, addr 4 (disconnected)
ums0: detached
ls -l /
total 4209 -rw-r--r-- 2 root wheel 950 Dec 23 15:27 .cshrc -rw-r--r-- 2 root wheel 242 Dec 23 15:27 .profile drwxrwxr-x 2 root operator 512 Dec 23 15:21 .snap -r-------- 1 root wheel 4194304 Dec 23 15:21 .sujournal -r--r--r-- 1 root wheel 6190 Dec 23 15:27 COPYRIGHT drwxr-xr-x 2 root wheel 1024 Dec 23 15:23 bin drwxr-xr-x 9 raspberry 1001 1024 Dec 23 15:41 boot dr-xr-xr-x 18 root wheel 512 Jun 16 20:09 dev -rw-r--r-- 1 root 1001 4096 Jun 16 20:09 entropy drwxr-xr-x 27 raspberry 1001 2560 Jun 16 20:12 etc drwxr-xr-x 4 root wheel 1536 Dec 23 15:24 lib drwxr-xr-x 3 root wheel 512 Dec 23 15:23 libexec drwxr-xr-x 2 root wheel 512 Dec 23 15:21 media drwxr-xr-x 4 root wheel 512 Jun 16 20:08 mnt dr-xr-xr-x 2 root wheel 512 Dec 23 15:21 proc drwxr-xr-x 2 root wheel 2560 Dec 23 15:23 rescue drwxr-xr-x 6 root wheel 512 Jun 20 11:59 root drwxr-xr-x 2 root wheel 2560 Dec 23 15:27 sbin lrwxr-xr-x 1 root wheel 11 Dec 23 15:27 sys -> usr/src/sys drwxrwxrwt 8 root wheel 512 Jun 20 03:41 tmp drwxr-xr-x 15 root wheel 512 Dec 23 15:29 usr drwxr-xr-x 25 root wheel 512 Jun 16 20:09 var total 2164
ls -lart /boot
drwxr-xr-x 1 root 1001 16384 Jan 1 1980 msdos -rw-r--r-- 1 raspberry 1001 335 Apr 29 2015 loader.rc drwxr-xr-x 2 root wheel 512 Dec 23 15:21 firmware drwxr-xr-x 2 root wheel 512 Dec 23 15:21 modules drwxr-xr-x 2 root wheel 512 Dec 23 15:21 zfs -r-xr-xr-x 1 root wheel 403660 Dec 23 15:25 loader.efi -r-xr-xr-x 1 root wheel 101444 Dec 23 15:25 boot1.efi -r--r--r-- 1 root wheel 819200 Dec 23 15:25 boot1.efifat drwxr-xr-x 2 root wheel 512 Dec 23 15:25 defaults -r--r--r-- 1 root wheel 5858 Dec 23 15:25 menu.rc.sample -r--r--r-- 1 root wheel 3550 Dec 23 15:25 beastie.4th -r--r--r-- 1 root wheel 2802 Dec 23 15:25 brand.4th -r--r--r-- 1 root wheel 2122 Dec 23 15:25 brand-fbsd.4th -r--r--r-- 1 root wheel 6201 Dec 23 15:25 check-password.4th -r--r--r-- 1 root wheel 1863 Dec 23 15:25 color.4th -r--r--r-- 1 root wheel 4049 Dec 23 15:25 delay.4th -r--r--r-- 1 root wheel 1486 Dec 23 15:25 efi.4th -r--r--r-- 1 root wheel 4172 Dec 23 15:25 frames.4th -r--r--r-- 1 root wheel 7494 Dec 23 15:25 loader.4th -r--r--r-- 1 root wheel 16918 Dec 23 15:25 loader.help -r--r--r-- 1 root wheel 3106 Dec 23 15:25 logo-beastie.4th -r--r--r-- 1 root wheel 2632 Dec 23 15:25 logo-beastiebw.4th -r--r--r-- 1 root wheel 2210 Dec 23 15:25 logo-fbsdbw.4th -r--r--r-- 1 root wheel 2627 Dec 23 15:25 logo-orb.4th -r--r--r-- 1 root wheel 2350 Dec 23 15:25 logo-orbbw.4th -r--r--r-- 1 root wheel 36012 Dec 23 15:25 menu.4th -r--r--r-- 1 root wheel 9256 Dec 23 15:25 menu-commands.4th -r--r--r-- 1 root wheel 18593 Dec 23 15:25 menusets.4th -r--r--r-- 1 root wheel 2671 Dec 23 15:25 screen.4th -r--r--r-- 1 root wheel 2609 Dec 23 15:25 shortcuts.4th -r--r--r-- 1 root wheel 36284 Dec 23 15:25 support.4th -r--r--r-- 1 root wheel 3061 Dec 23 15:25 version.4th drwxr-xr-x 2 root wheel 512 Dec 23 15:29 dtb drwxr-xr-x 2 root 1001 11776 Dec 23 15:29 kernel -r--r--r-- 1 root wheel 283886 Dec 23 15:29 ubldr -r--r--r-- 1 root wheel 231800 Dec 23 15:29 ubldr.bin drwxr-xr-x 9 raspberry 1001 1024 Dec 23 15:41 . -rw-r--r-- 1 root 1001 4096 Jun 16 20:09 entropy drwxr-xr-x 18 raspberry 1001 1024 Jun 16 20:09 ..
gpart show (equivalent to fdisk)
=> 63 62521281 mmcsd0 MBR (30G)
63 102375 1 !12 [active] (50M)
102438 62418906 2 freebsd (30G)
=> 0 62418906 mmcsd0s2 BSD (30G)
0 90 - free - (45K)
90 62418816 1 freebsd-ufs (30G)
This is from FreeBSD running on a Raspeberry Pi booted from a 32GB MicroSDHC card. There was no such directory as /lib/modules. Maybe what you want is called something else on FreeBSD. This will give you the layout of the filesystem on FreeBSD. Any applications which are not part of the core OS are installed under /usr/local
https://www.freebsd.org/cgi/man.cgi?hier(7)
|
Re: Is uBoot OS specific? June 20, 2017 07:40AM |
Registered: 7 years ago Posts: 337 |
|
Re: Is uBoot OS specific? June 20, 2017 04:25PM |
Admin Registered: 14 years ago Posts: 19,558 |
balanga Wrote:
-------------------------------------------------------
> That should be:-
>
> https://www.freebsd.org/cgi/man.cgi?query=hier&man
> path=FreeBSD+6.1-RELEASE&format=html
That's interesting. But what you should do next is googling "FreeBSD u-boot" to find out how other people did this.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> That should be:-
>
> https://www.freebsd.org/cgi/man.cgi?query=hier&man
> path=FreeBSD+6.1-RELEASE&format=html
That's interesting. But what you should do next is googling "FreeBSD u-boot" to find out how other people did this.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Is uBoot OS specific? June 20, 2017 05:33PM |
Registered: 7 years ago Posts: 337 |
To be quite honest, this is a very technical area, and most of the hits show pages which I don't understand. There are so many pages which span quite a period and relate to wide range of hardware that it is difficult to limit the search to my situation. I will study the link which you provided earlier and see if I can make anything of it,
|
Re: Is uBoot OS specific? June 20, 2017 05:57PM |
Admin Registered: 14 years ago Posts: 19,558 |
balanga Wrote:
-------------------------------------------------------
> To be quite honest, this is a very technical area,
> and most of the hits show pages which I don't unde
> rstand. There are so many pages which span quite a
> period and relate to wide range of hardware that i
> t is difficult to limit the search to my situation
> . I will study the link which you provided earlier
> and see if I can make anything of it,
There is really no hardware specifics in this. Basically you want to search for topics that peole discuss how to set up u-boot to boot FreeBSD. For example,
- Is the ubldr the boot file for FreeBSD?
- which file is FreeBSD kernel file?
- Where is the DTB? is it built in to BSD kernel file?
Things like that.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> To be quite honest, this is a very technical area,
> and most of the hits show pages which I don't unde
> rstand. There are so many pages which span quite a
> period and relate to wide range of hardware that i
> t is difficult to limit the search to my situation
> . I will study the link which you provided earlier
> and see if I can make anything of it,
There is really no hardware specifics in this. Basically you want to search for topics that peole discuss how to set up u-boot to boot FreeBSD. For example,
- Is the ubldr the boot file for FreeBSD?
- which file is FreeBSD kernel file?
- Where is the DTB? is it built in to BSD kernel file?
Things like that.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Is uBoot OS specific? June 29, 2017 08:36AM |
Registered: 9 years ago Posts: 298 |
https://cooltrainer.org/freebsd-kirkwood/installation/
Sounds easy enough, uboot basically has to load "kernel.bin" to RAM and then just execute it. You seem to have a file called "kernel" in your boot partition so I guess it's that the one in more modern FreeBSD.
for example (from serial console, if from linux use fw_setenv instead of setenv)
setenv bootcmd 'usb reset; fatload usb 0:1 0x900000 /boot/kernel; go 0x900000'
would set your device for looking into first partition of first usb device, which is formatted as FAT32, and load a file called kernel from inside the /boot folder, and then plain execute it.
You can also make something more complex as stated in the link above, if you want it to be able to find the right USB drive if you have more than one connected. Or boot from Sata drives, just write "ide" instead of "usb" in the line above.
Or you can keep the whole /boot folder as a separate partition on FAT32 if you want to keep your rootfs on UDF or whatever other filesystem. In that case change the "/boot/kernel" from above into "kernel", and add a line in FreeBSD's fstab to mount that partition over /boot folder.
The hard part seems to be getting a freebsd kernel/OS compiled for it.
EDIT: saw your posts on bsd forum, add
V=s
as an argument to your make. That is verbose mode. It will allow you to see what is going on, as long as it keeps spewing text it's probably still working.
Edited 3 time(s). Last edit at 06/29/2017 08:52AM by bobafetthotmail.
Sounds easy enough, uboot basically has to load "kernel.bin" to RAM and then just execute it. You seem to have a file called "kernel" in your boot partition so I guess it's that the one in more modern FreeBSD.
for example (from serial console, if from linux use fw_setenv instead of setenv)
setenv bootcmd 'usb reset; fatload usb 0:1 0x900000 /boot/kernel; go 0x900000'
would set your device for looking into first partition of first usb device, which is formatted as FAT32, and load a file called kernel from inside the /boot folder, and then plain execute it.
You can also make something more complex as stated in the link above, if you want it to be able to find the right USB drive if you have more than one connected. Or boot from Sata drives, just write "ide" instead of "usb" in the line above.
Or you can keep the whole /boot folder as a separate partition on FAT32 if you want to keep your rootfs on UDF or whatever other filesystem. In that case change the "/boot/kernel" from above into "kernel", and add a line in FreeBSD's fstab to mount that partition over /boot folder.
The hard part seems to be getting a freebsd kernel/OS compiled for it.
EDIT: saw your posts on bsd forum, add
V=s
as an argument to your make. That is verbose mode. It will allow you to see what is going on, as long as it keeps spewing text it's probably still working.
Edited 3 time(s). Last edit at 06/29/2017 08:52AM by bobafetthotmail.
|
Re: Is uBoot OS specific? July 19, 2017 05:57AM |
Registered: 7 years ago Posts: 337 |
bobafetthotmail Wrote:
-------------------------------------------------------
> https://cooltrainer.org/freebsd-kirkwood/installat
> ion/
>
> Sounds easy enough, uboot basically has to load "k
> ernel.bin" to RAM and then just execute it. You se
> em to have a file called "kernel" in your boot par
> tition so I guess it's that the one in more modern
> FreeBSD.
>
> for example (from serial console, if from linux us
> e fw_setenv instead of setenv)
>
> setenv bootcmd 'usb reset; fatload usb 0:1 0x90000
> 0 /boot/kernel; go 0x900000'
>
> would set your device for looking into first parti
> tion of first usb device, which is formatted as FA
> T32, and load a file called kernel from inside the
> /boot folder, and then plain execute it.
>
> You can also make something more complex as stated
> in the link above, if you want it to be able to fi
> nd the right USB drive if you have more than one c
> onnected. Or boot from Sata drives, just write "id
> e" instead of "usb" in the line above.
>
> Or you can keep the whole /boot folder as a separa
> te partition on FAT32 if you want to keep your roo
> tfs on UDF or whatever other filesystem. In that c
> ase change the "/boot/kernel" from above into "ker
> nel", and add a line in FreeBSD's fstab to mount t
> hat partition over /boot folder.
>
> The hard part seems to be getting a freebsd kernel
> /OS compiled for it.
>
> EDIT: saw your posts on bsd forum, add
> V=s
> as an argument to your make. That is verbose mode.
> It will allow you to see what is going on, as long
> as it keeps spewing text it's probably still worki
> ng.
I've had a bit of a break from my GFH project, but having just seen your post, I thought I'd resume... Firstly, I'd just like to mention that I'm rather out of my depth trying to do what I'd want, which is to run FreeBSD on my GoFlexHome unit... Having searched various forums, websites, mailing lists, it seems like solutions exist, but instructions are not always up to date, or unclear.. My experience so far as shown me how to replace the stock Seagate software, lock myself out, connect via a serial cable and unlock myself. All this thanks to help from bodhi on this forum and the FreeBSD forum.
Reading your post, I take it that my first task is to try and build a FreeBSD image using instructions here:-
https://cooltrainer.org/freebsd-kirkwood/building/
Unfortunately some of the instructions don't work and they are based on FreeBSD v8 and the current release is v11...but I'll see how far I can get. I expect it will take me a few days to get anywhere with it.
-------------------------------------------------------
> https://cooltrainer.org/freebsd-kirkwood/installat
> ion/
>
> Sounds easy enough, uboot basically has to load "k
> ernel.bin" to RAM and then just execute it. You se
> em to have a file called "kernel" in your boot par
> tition so I guess it's that the one in more modern
> FreeBSD.
>
> for example (from serial console, if from linux us
> e fw_setenv instead of setenv)
>
> setenv bootcmd 'usb reset; fatload usb 0:1 0x90000
> 0 /boot/kernel; go 0x900000'
>
> would set your device for looking into first parti
> tion of first usb device, which is formatted as FA
> T32, and load a file called kernel from inside the
> /boot folder, and then plain execute it.
>
> You can also make something more complex as stated
> in the link above, if you want it to be able to fi
> nd the right USB drive if you have more than one c
> onnected. Or boot from Sata drives, just write "id
> e" instead of "usb" in the line above.
>
> Or you can keep the whole /boot folder as a separa
> te partition on FAT32 if you want to keep your roo
> tfs on UDF or whatever other filesystem. In that c
> ase change the "/boot/kernel" from above into "ker
> nel", and add a line in FreeBSD's fstab to mount t
> hat partition over /boot folder.
>
> The hard part seems to be getting a freebsd kernel
> /OS compiled for it.
>
> EDIT: saw your posts on bsd forum, add
> V=s
> as an argument to your make. That is verbose mode.
> It will allow you to see what is going on, as long
> as it keeps spewing text it's probably still worki
> ng.
I've had a bit of a break from my GFH project, but having just seen your post, I thought I'd resume... Firstly, I'd just like to mention that I'm rather out of my depth trying to do what I'd want, which is to run FreeBSD on my GoFlexHome unit... Having searched various forums, websites, mailing lists, it seems like solutions exist, but instructions are not always up to date, or unclear.. My experience so far as shown me how to replace the stock Seagate software, lock myself out, connect via a serial cable and unlock myself. All this thanks to help from bodhi on this forum and the FreeBSD forum.
Reading your post, I take it that my first task is to try and build a FreeBSD image using instructions here:-
https://cooltrainer.org/freebsd-kirkwood/building/
Unfortunately some of the instructions don't work and they are based on FreeBSD v8 and the current release is v11...but I'll see how far I can get. I expect it will take me a few days to get anywhere with it.
|
Re: Is uBoot OS specific? July 19, 2017 07:38AM |
Registered: 12 years ago Posts: 1,303 |
balanga Wrote:
-------------------------------------------------------
> Reading your post, I take it that my first task is to try and build a FreeBSD image using instructions here:-
> https://cooltrainer.org/freebsd-kirkwood/building/
> Unfortunately some of the instructions don't work and they are based on FreeBSD v8 and the current release is v11...but I'll see how far I can get. I expect it will take me a few days to get anywhere with it.
>
If you are looking for the source code of a FreeBSD for Kirkwood, perhaps this GitHUB repo is what you need? Perhaps, you need to visit Building FreeBSD for Kirkwood discussion forum to learn more on how to build FreeBSD for a Kirkwood platform?
-------------------------------------------------------
> Reading your post, I take it that my first task is to try and build a FreeBSD image using instructions here:-
> https://cooltrainer.org/freebsd-kirkwood/building/
> Unfortunately some of the instructions don't work and they are based on FreeBSD v8 and the current release is v11...but I'll see how far I can get. I expect it will take me a few days to get anywhere with it.
>
If you are looking for the source code of a FreeBSD for Kirkwood, perhaps this GitHUB repo is what you need? Perhaps, you need to visit Building FreeBSD for Kirkwood discussion forum to learn more on how to build FreeBSD for a Kirkwood platform?
|
Re: Is uBoot OS specific? July 19, 2017 01:48PM |
Registered: 7 years ago Posts: 337 |
habibie Wrote:
-------------------------------------------------------
> balanga Wrote:
> --------------------------------------------------
> -----
> > Reading your post, I take it that my first task
> is to try and build a FreeBSD image using instruct
> ions here:-
> > https://cooltrainer.org/freebsd-kirkwood/buildin
> g/
> > Unfortunately some of the instructions don't wor
> k and they are based on FreeBSD v8 and the current
> release is v11...but I'll see how far I can get. I
> expect it will take me a few days to get anywhere
> with it.
> >
> If you are looking for the source code of a FreeBS
> D for Kirkwood, perhaps this [url=https://github.c
> om/okeeblow/FreeBSD-kirkwood]GitHUB[/url] repo is
> what you need? Perhaps, you need to visit [url=htt
> ps://forums.freebsd.org/threads/61375]Building Fre
> eBSD for Kirkwood[/url] discussion forum to learn
> more on how to build FreeBSD for a Kirkwood platfo
> rm?
Actually, that is a thread I started.... Having looked at building FreeBSD today, it looks like the latest FreeBSD source (v11.0) includes all the necessary source and no patches are required, as far as I can tell. What I need to figure out now is to install FreeBSD on a USB stick and launch it from U-Boot. Not sure if need a different U-Boot...
-------------------------------------------------------
> balanga Wrote:
> --------------------------------------------------
> -----
> > Reading your post, I take it that my first task
> is to try and build a FreeBSD image using instruct
> ions here:-
> > https://cooltrainer.org/freebsd-kirkwood/buildin
> g/
> > Unfortunately some of the instructions don't wor
> k and they are based on FreeBSD v8 and the current
> release is v11...but I'll see how far I can get. I
> expect it will take me a few days to get anywhere
> with it.
> >
> If you are looking for the source code of a FreeBS
> D for Kirkwood, perhaps this [url=https://github.c
> om/okeeblow/FreeBSD-kirkwood]GitHUB[/url] repo is
> what you need? Perhaps, you need to visit [url=htt
> ps://forums.freebsd.org/threads/61375]Building Fre
> eBSD for Kirkwood[/url] discussion forum to learn
> more on how to build FreeBSD for a Kirkwood platfo
> rm?
Actually, that is a thread I started.... Having looked at building FreeBSD today, it looks like the latest FreeBSD source (v11.0) includes all the necessary source and no patches are required, as far as I can tell. What I need to figure out now is to install FreeBSD on a USB stick and launch it from U-Boot. Not sure if need a different U-Boot...
|
Re: Is uBoot OS specific? July 19, 2017 05:54PM |
Admin Registered: 14 years ago Posts: 19,558 |
balanga,
>What I need to figure out now is to
> install FreeBSD on a USB stick and launch it from
> U-Boot. Not sure if need a different U-Boot...
I think you also need to verify which are the boot files on the FreeBSD rootfs. I briefly searched for this topic, and I can see that a "ubldr.bin" or something like that is used in booting. This is most likely because u-boot mainline does not deal with FreeBSD directly, but it can load a binary and run it. So the "ubldr.bin" is a FreeBSD loader.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
>What I need to figure out now is to
> install FreeBSD on a USB stick and launch it from
> U-Boot. Not sure if need a different U-Boot...
I think you also need to verify which are the boot files on the FreeBSD rootfs. I briefly searched for this topic, and I can see that a "ubldr.bin" or something like that is used in booting. This is most likely because u-boot mainline does not deal with FreeBSD directly, but it can load a binary and run it. So the "ubldr.bin" is a FreeBSD loader.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Is uBoot OS specific? July 20, 2017 07:26AM |
Registered: 12 years ago Posts: 1,303 |
balanga Wrote:
-------------------------------------------------------
> Actually, that is a thread I started.... Having lo oked at building FreeBSD today, it looks like the latest FreeBSD source (v11.0) includes all the necessary source and no patches are required, as far as I can tell. What I need to figure out now is to install FreeBSD on a USB stick and launch it from U-Boot. Not sure if need a different U-Boot...
>
R U talking about this latest FreeBSD source?
-------------------------------------------------------
> Actually, that is a thread I started.... Having lo oked at building FreeBSD today, it looks like the latest FreeBSD source (v11.0) includes all the necessary source and no patches are required, as far as I can tell. What I need to figure out now is to install FreeBSD on a USB stick and launch it from U-Boot. Not sure if need a different U-Boot...
>
R U talking about this latest FreeBSD source?
|
Re: Is uBoot OS specific? July 20, 2017 01:03PM |
Registered: 7 years ago Posts: 337 |
habibie Wrote:
-------------------------------------------------------
> balanga Wrote:
> --------------------------------------------------
> -----
> > Actually, that is a thread I started.... Having
> lo oked at building FreeBSD today, it looks like t
> he latest FreeBSD source (v11.0) includes all the
> necessary source and no patches are required, as f
> ar as I can tell. What I need to figure out now is
> to install FreeBSD on a USB stick and launch it fr
> om U-Boot. Not sure if need a different U-Boot...
> >
> R U talking about this [url=https://github.com/fre
> ebsd/freebsd]latest FreeBSD source[/url]?
No, I'm talking about the latest RELEASE version:-
[url]http://ftp.freebsd.org/pub/FreeBSD/releases/amd64/amd64/11.0-RELEASE/src.txz[/url]
Using:-
make buildworld TARGET_ARCH=arm -DWITH_FDT
make buildkernel TARGET_ARCH=arm KERNCONF=DB-88F6XXX
Unfortunately I don't know how to launch this, so I can't test it.
-------------------------------------------------------
> balanga Wrote:
> --------------------------------------------------
> -----
> > Actually, that is a thread I started.... Having
> lo oked at building FreeBSD today, it looks like t
> he latest FreeBSD source (v11.0) includes all the
> necessary source and no patches are required, as f
> ar as I can tell. What I need to figure out now is
> to install FreeBSD on a USB stick and launch it fr
> om U-Boot. Not sure if need a different U-Boot...
> >
> R U talking about this [url=https://github.com/fre
> ebsd/freebsd]latest FreeBSD source[/url]?
No, I'm talking about the latest RELEASE version:-
[url]http://ftp.freebsd.org/pub/FreeBSD/releases/amd64/amd64/11.0-RELEASE/src.txz[/url]
Using:-
make buildworld TARGET_ARCH=arm -DWITH_FDT
make buildkernel TARGET_ARCH=arm KERNCONF=DB-88F6XXX
Unfortunately I don't know how to launch this, so I can't test it.
|
Re: Is uBoot OS specific? July 20, 2017 05:02PM |
Admin Registered: 14 years ago Posts: 19,558 |
balanga,
> No, I'm talking about the latest RELEASE version:-
>
> http://ftp.freebsd.org/pub/FreeBSD/releases/amd64/
> amd64/11.0-RELEASE/src.txz
Looks like x86 architecture, not ARM.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> No, I'm talking about the latest RELEASE version:-
>
> http://ftp.freebsd.org/pub/FreeBSD/releases/amd64/
> amd64/11.0-RELEASE/src.txz
Looks like x86 architecture, not ARM.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Is uBoot OS specific? July 20, 2017 10:05PM |
Registered: 12 years ago Posts: 1,303 |
bodhi Wrote:
-------------------------------------------------------
> balanga,
>
> > No, I'm talking about the latest RELEASE version
> :-
> >
> > http://ftp.freebsd.org/pub/FreeBSD/releases/amd64/amd64/11.0-RELEASE/src.txz
>
> Looks like x86 architecture, not ARM.
>
It does appear so. But, it contains the source code of $FreeBSD: releng/11.0/README 300137 2016-05-18 10:43:13Z avos $
-------------------------------------------------------
> balanga,
>
> > No, I'm talking about the latest RELEASE version
> :-
> >
> > http://ftp.freebsd.org/pub/FreeBSD/releases/amd64/amd64/11.0-RELEASE/src.txz
>
> Looks like x86 architecture, not ARM.
>
It does appear so. But, it contains the source code of $FreeBSD: releng/11.0/README 300137 2016-05-18 10:43:13Z avos $
|
Re: Is uBoot OS specific? July 21, 2017 07:43AM |
Registered: 7 years ago Posts: 337 |
There is also
http://ftp.freebsd.org/pub/FreeBSD/releases/arm64/11.0-RELEASE/src.txz
but it is the same file. There's only a single source tree.
Any suggestions as to what I should put in uEnv.txt to try and boot FreeBSD?
I've tried
uimage=/boot/kernel.bin
but get
reading /boot/kernel.bin
4408164 bytes read in 249 ms (16.9 MiB/s)
Booting from 0 ...
Wrong Image Format for bootm command
Where can I find a list of options which I can put in uEnv.txt?
http://ftp.freebsd.org/pub/FreeBSD/releases/arm64/11.0-RELEASE/src.txz
but it is the same file. There's only a single source tree.
Any suggestions as to what I should put in uEnv.txt to try and boot FreeBSD?
I've tried
uimage=/boot/kernel.bin
but get
reading /boot/kernel.bin
4408164 bytes read in 249 ms (16.9 MiB/s)
Booting from 0 ...
Wrong Image Format for bootm command
Where can I find a list of options which I can put in uEnv.txt?
|
Re: Is uBoot OS specific? July 21, 2017 08:45AM |
Registered: 7 years ago Posts: 337 |
|
Re: Is uBoot OS specific? July 21, 2017 02:17PM |
Admin Registered: 14 years ago Posts: 19,558 |
bodhi Wrote:
-------------------------------------------------------
> balanga,
>
> >What I need to figure out now is to
> > install FreeBSD on a USB stick and launch it fro
> m
> > U-Boot. Not sure if need a different U-Boot...
>
> I think you also need to verify which are the boot
> files on the FreeBSD rootfs. I briefly searched fo
> r this topic, and I can see that a "ubldr.bin" or
> something like that is used in booting. This is mo
> st likely because u-boot mainline does not deal wi
> th FreeBSD directly, but it can load a binary and
> run it. So the "ubldr.bin" is a FreeBSD loader.
balanga,
Please read what I wrote above. bootm is for Linux.
You need to do more research and find out how people boot FreeBSD with u-boot. If you are not sure that you understand those instruction, then post them here. Perhaps I can help that way.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> balanga,
>
> >What I need to figure out now is to
> > install FreeBSD on a USB stick and launch it fro
> m
> > U-Boot. Not sure if need a different U-Boot...
>
> I think you also need to verify which are the boot
> files on the FreeBSD rootfs. I briefly searched fo
> r this topic, and I can see that a "ubldr.bin" or
> something like that is used in booting. This is mo
> st likely because u-boot mainline does not deal wi
> th FreeBSD directly, but it can load a binary and
> run it. So the "ubldr.bin" is a FreeBSD loader.
balanga,
Please read what I wrote above. bootm is for Linux.
You need to do more research and find out how people boot FreeBSD with u-boot. If you are not sure that you understand those instruction, then post them here. Perhaps I can help that way.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Is uBoot OS specific? July 21, 2017 03:43PM |
Registered: 7 years ago Posts: 337 |
I thought that the easiest way to understand how things work and make some progress would be load a file over the network and execute it...
If I run DHCP, I retreive a file called gpxelinux.0. The system displays:-
TFTP fromserver 192.168.1.2; our IP address is 192.168.1.47
Filename 'gpxelinux.0'
Load address: 0x810000
Loading: ########
5.3 MiB/s
done
Bytes transferred = 111334 (1b2e6 hex)
GoFlexHome>
What I thought I should be able to do was run this program using
go 0x810000
I get
## Starting application at 0x00810000
and then nothing. Not sure if what I'm attempting makes any sense or what myresults show...
If I run DHCP, I retreive a file called gpxelinux.0. The system displays:-
TFTP fromserver 192.168.1.2; our IP address is 192.168.1.47
Filename 'gpxelinux.0'
Load address: 0x810000
Loading: ########
5.3 MiB/s
done
Bytes transferred = 111334 (1b2e6 hex)
GoFlexHome>
What I thought I should be able to do was run this program using
go 0x810000
I get
## Starting application at 0x00810000
and then nothing. Not sure if what I'm attempting makes any sense or what myresults show...
|
Re: Is uBoot OS specific? July 21, 2017 10:39PM |
Registered: 12 years ago Posts: 1,303 |
balanga Wrote:
-------------------------------------------------------
> Reading your post, I take it that my first task is to try and build a FreeBSD image using instructions here:-
> https://cooltrainer.org/freebsd-kirkwood/building/
> Unfortunately some of the instructions don't work and they are based on FreeBSD v8 and the current release is v11...but I'll see how far I can get. I
> expect it will take me a few days to get anywhere with it.
>
I did some googling and foudn this How to build a FreeBSD toolchain for Linux and don't know if this may help or not. I basically is aguide on how to create a FreeBSD toolchain (v10) for Linux platform. once you have such a toolchain, perhaps building a FreeBSD will become more obvious?
-------------------------------------------------------
> Reading your post, I take it that my first task is to try and build a FreeBSD image using instructions here:-
> https://cooltrainer.org/freebsd-kirkwood/building/
> Unfortunately some of the instructions don't work and they are based on FreeBSD v8 and the current release is v11...but I'll see how far I can get. I
> expect it will take me a few days to get anywhere with it.
>
I did some googling and foudn this How to build a FreeBSD toolchain for Linux and don't know if this may help or not. I basically is aguide on how to create a FreeBSD toolchain (v10) for Linux platform. once you have such a toolchain, perhaps building a FreeBSD will become more obvious?
