|
z0rg
Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 15, 2018 03:05PM |
U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27)
Boot device: NAND
Attempting to set PLLA to 800 MHz ...
plla_ctrl0 : 0000030a
plla_ctrl1 : 00400000
plla_ctrl2 : 007f0068
plla_ctrl3 : 00000193
PLLA Set
-bash-4.0# cat /proc/mtd dev: size erasesize name mtd0: 10000000 00020000 "NAND 256MiB 3,3V 8-bit" mtd1: 026c0000 00020000 "Boot partition" mtd2: 0d940000 00020000 "Data Partition"
|
Re: Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 15, 2018 04:21PM |
Admin Registered: 13 years ago Posts: 19,092 |
> -bash-4.0# cat /proc/mtd > dev: size erasesize name > mtd0: 10000000 00020000 "NAND 256MiB 3,3V 8-bit" > mtd1: 026c0000 00020000 "Boot partition" > mtd2: 0d940000 00020000 "Data Partition" > >
|
z0rg
Re: Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 15, 2018 10:01PM |
Stage-1 Bootloader Thu Jun 3 10:29:14 PDT 2010
Attempting to set PLLA to 700MHz ...
plla_ctrl0 : 0x00000118
plla_ctrl1 : 0x00380000
plla_ctrl2 : 0x006F00D0
plla_ctrl3 : 0x000000B0
PLLA Set
Setup memory, testing
Reading NAND, Image 0
Failed to correct error
Failed to correct error
Hdr len: 0xA1A2A3A4
Hdr CRC: 0xB1B2B3B4
read failed
Reading NAND, Image 1
Hdr len: 0x0001AB60
Hdr CRC: 0xE0B0E526
OK
U-Boot 1.1.2 (Mar 2 2011 - 10:17:22)
U-Boot code: 60D00000 -> 60D1AB60 BSS: -> 60D1F218
RAM Configuration:
Bank #0: 60000000 128 MB
SRAM Configuration:
64KB at 0x50000000
NAND:256 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Setting Linux mem= boot arg value
Reading upgrade flag from NAND address 0x01ec0000 : 0
Hit any key to stop autoboot: 0
Extinguish LED
Loading from device 0: 256MiB 3,3V 8-bit (offset 0x440000)
Image Name: Linux-2.6.31.14-fast-20110422
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3078316 Bytes = 2.9 MB
Load Address: 60008000
Entry Point: 60008000
## Booting image at 60500000 ...
Image Name: Linux-2.6.31.14-fast-20110422
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3078316 Bytes = 2.9 MB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux.............................................................
Linux version 2.6.31.14-fast-20110422 (root@thom) (gcc version 4.4.2 20091019 (1
CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Oxsemi NAS
1 memory region
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writealloc
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: root=ubi0:rootfs ubi.mtd=2,512 rootfstype=ubifs console=tts
PID hash table entries: 512 (order: 9, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 123860KB available (5280K code, 311K data, 148K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:96
OX820_RPS_init_irq: interrupts 64 to 96
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Calibrating local timer... 349.98MHz.
CPU1: Booted secondary processor
Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736)
Brought up 2 CPUs
SMP: Total of 2 processors activated (558.69 BogoMIPS).
NET: Registered protocol family 16
Number of DMA channels = 4, version = 4
Reserving a DMA channel for ODRB
Allocating 645 SRAM generic DMA descriptors
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
Switched to NOHz mode on CPU #0
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Switched to NOHz mode on CPU #1
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
Create fragment cache
fuse init (API version 7.12)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
msgmni has been set to 242
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
brd: module loaded
loop: module loaded
ox820sata: OX820 sata core.
scsi0 : oxnassata
scsi1 : oxnassata
ata1: SATA max UDMA/133 irq 50
ata2: SATA max UDMA/133 irq 50
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 2 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x000000000000-0x0000026c0000 : "Boot partition"
0x0000026c0000-0x000010000000 : "Data Partition"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd2 to ubi0
UBI: MTD device name: "Data Partition"
UBI: MTD device size: 217 MiB
UBI: number of good PEBs: 1738
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 1738
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 87/10
UBI: image sequence number: 580785302
UBI: background thread "ubi_bgt0d" started, PID 398
Probing for Synopsis GMAC, unit 0
eth0: use mtd hwaddr
eth0: Tuning GMAC 0 RGMII timings
eth0: PHY is Realtek RTL8211D, type 0x001cc914
eth0: GMAC ver = 53, vendor ver = 18 at 0xe1400000, IRQ 40
eth0: Found PHY at address 3, type 0x001cc914 -> 10/100/1000
eth0: Ethernet addr: 00:01:d2:12:08:12
probe() eth0: Leon x2 clock
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Start USB clocks
oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1
oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000
oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
IRQ 53 uses trigger mode 0; requested 3
input: gpio-keys as /devices/platform/gpio-keys/input/input0
irq 54: nobody cared (try booting with the "irqpoll" option)
[<c0032bb0>] (unwind_backtrace+0x0/0xe8) from [<c007992c>] (__report_bad_irq+0x)
[<c007992c>] (__report_bad_irq+0x74/0xa4) from [<c0079adc>] (note_interrupt+0x1)
[<c0079adc>] (note_interrupt+0x180/0x1ec) from [<c007a484>] (handle_level_irq+0)
[<c007a484>] (handle_level_irq+0x100/0x128) from [<c002d058>] (asm_do_IRQ+0x58/)
[<c002d058>] (asm_do_IRQ+0x58/0xac) from [<c002dbf8>] (__irq_svc+0x38/0xc0)
Exception stack(0xc7829b38 to 0xc7829b80)
9b20: c7829b80 ffff8bf3
9b40: 0000000a 00000000 00000000 00000102 c7828000 c0570040 00000000 c05a3f20
9b60: c00258b8 c0570040 00000000 c7829b80 c00539fc c0053894 20000113 ffffffff
[<c002dbf8>] (__irq_svc+0x38/0xc0) from [<c0053894>] (__do_softirq+0x58/0x140)
[<c0053894>] (__do_softirq+0x58/0x140) from [<c00539fc>] (irq_exit+0x80/0x9c)
[<c00539fc>] (irq_exit+0x80/0x9c) from [<c002d05c>] (asm_do_IRQ+0x5c/0xac)
[<c002d05c>] (asm_do_IRQ+0x5c/0xac) from [<c002dbf8>] (__irq_svc+0x38/0xc0)
Exception stack(0xc7829be0 to 0xc7829c28)
9be0: c059657c 60000013 e500001c 00000000 00000000 e510001c 00000029 c05aae80
9c00: 00000000 00000000 60000013 00000000 00000000 c7829c28 c0037d00 c03f64ac
9c20: 20000013 ffffffff
[<c002dbf8>] (__irq_svc+0x38/0xc0) from [<c03f64ac>] (_spin_unlock_irqrestore+0)
[<c03f64ac>] (_spin_unlock_irqrestore+0x14/0x18) from [<c0037d00>] (ox820_gpio_)
[<c0037d00>] (ox820_gpio_direction_output+0x60/0xa8) from [<c025d4d4>] (gpio_di)
[<c025d4d4>] (gpio_direction_output+0xcc/0xec) from [<c02ee358>] (i2c_start+0x1)
[<c02ee358>] (i2c_start+0x18/0x44) from [<c02ee9e4>] (bit_xfer+0x24/0x488)
[<c02ee9e4>] (bit_xfer+0x24/0x488) from [<c02ec5e4>] (i2c_transfer+0xb0/0xf0)
[<c02ec5e4>] (i2c_transfer+0xb0/0xf0) from [<c02ec8a0>] (i2c_smbus_xfer+0x27c/0)
[<c02ec8a0>] (i2c_smbus_xfer+0x27c/0x544) from [<c02ecc08>] (i2c_smbus_read_i2c)
[<c02ecc08>] (i2c_smbus_read_i2c_block_data+0x4c/0x70) from [<c03f31b4>] (ds130)
[<c03f31b4>] (ds1307_probe+0x354/0x5fc) from [<c02ec3d4>] (i2c_device_probe+0x9)
[<c02ec3d4>] (i2c_device_probe+0x98/0xb0) from [<c027ffb0>] (driver_probe_devic)
[<c027ffb0>] (driver_probe_device+0x78/0x164) from [<c027f5d4>] (bus_for_each_d)
[<c027f5d4>] (bus_for_each_drv+0x60/0x8c) from [<c02801ec>] (device_attach+0x5c)
[<c02801ec>] (device_attach+0x5c/0x74) from [<c027f3e8>] (bus_probe_device+0x24)
[<c027f3e8>] (bus_probe_device+0x24/0x44) from [<c027df88>] (device_add+0x3f0/0)
[<c027df88>] (device_add+0x3f0/0x4d8) from [<c02ed604>] (i2c_new_device+0xbc/0x)
[<c02ed604>] (i2c_new_device+0xbc/0x124) from [<c02ee064>] (i2c_register_adapte)
[<c02ee064>] (i2c_register_adapter+0x124/0x1c4) from [<c02ee1b4>] (i2c_add_numb)
[<c02ee1b4>] (i2c_add_numbered_adapter+0xb0/0xc8) from [<c03f35d4>] (i2c_gpio_p)
[<c03f35d4>] (i2c_gpio_probe+0x178/0x22c) from [<c0280d98>] (platform_drv_probe)
[<c0280d98>] (platform_drv_probe+0x18/0x1c) from [<c027ffb0>] (driver_probe_dev)
[<c027ffb0>] (driver_probe_device+0x78/0x164) from [<c0280128>] (__driver_attac)
[<c0280128>] (__driver_attach+0x8c/0x90) from [<c027f8a4>] (bus_for_each_dev+0x)
[<c027f8a4>] (bus_for_each_dev+0x60/0x8c) from [<c027f17c>] (bus_add_driver+0x9)
[<c027f17c>] (bus_add_driver+0x9c/0x230) from [<c02803bc>] (driver_register+0x7)
[<c02803bc>] (driver_register+0x78/0x138) from [<c001d3d0>] (i2c_gpio_init+0xc/)
[<c001d3d0>] (i2c_gpio_init+0xc/0x30) from [<c002d4bc>] (do_one_initcall+0x30/0)
[<c002d4bc>] (do_one_initcall+0x30/0x1b4) from [<c0008554>] (kernel_init+0x164/)
[<c0008554>] (kernel_init+0x164/0x1f0) from [<c002eac0>] (kernel_thread_exit+0x)
handlers:
[<c02e97f4>] (gpio_keys_isr+0x0/0x8c)
Disabling IRQ #54
rtc-ds1307 0-0068: rtc core: registered m41t00 as rtc0
i2c-gpio i2c-gpio.0: using pins 41 (SDA) and 42 (SCL)
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
Registered led device: hddaerr
Registered led device: hddberr
Registered led device: system
Registered led device: firmware
Registered led device: usbcopy
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-ds1307 0-0068: setting system clock to 2018-01-16 11:33:45 UTC (1516102425)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
UBIFS: recovery needed
usb 1-1: new high speed USB device using oxnas-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 217921536 bytes (212814 KiB, 207 MiB, 1689 LEBs)
UBIFS: journal size: 9033728 bytes (8822 KiB, 8 MiB, 71 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:10.
Freeing init memory: 148K
Welcome to Fedora
Press 'I' to enter interactive startup.
Starting udev: [ OK ]
Setting hostname myhostname: [ OK ]
Checking filesystems
Checking all file systems.
[ OK ]
Mounting local filesystems: [ OK ]
Enabling /etc/fstab swaps: [ OK ]
Entering non-interactive startup
Bringing up loopback interface: [ OK ]
Bringing up interface eth0:
Determining IP information for eth0... failed; no link present. Check cable?
[FAILED]
Starting portreserve: [ OK ]
Starting system logger: [ OK ]
Starting rpcbind: [ OK ]
Starting NFS statd: [ OK ]
Starting RPC idmapd: [ OK ]
Starting system message bus: [ OK ]
Starting Avahi daemon... [ OK ]
Starting cups: [ OK ]
Mounting other filesystems: [ OK ]
Retrigger failed udev events[ OK ]
Starting NFS services: [ OK ]
Starting NFS daemon: rpc.nfsd: unable to resolve ANYADDR:nfs to inet address: Nn
rpc.nfsd: unable to set any sockets for nfsd
[FAILED]
Starting xinetd: [ OK ]
ntpdate: Synchronizing with time server: [FAILED]
Starting ntpd: [ OK ]
Starting vsftpd for vsftpd: [ OK ]
/etc/rc3.d/S90mldonkey: line 16: /etc/sysconfig/mldonkey: No such file or direcy
Starting Mldonkey (mlnet):
runuser: unrecognized option '--check'
Try `runuser --help' for more information.
[FAILED]
Starting Netatalk services:
Starting cnid_metad:[ OK ]
Starting afpd:[ OK ]
Starting NMB services: [ OK ]
Starting SMB services: [ OK ]
[ OK ] atd: [ OK ]
Starting DAAP server: [ OK ]
Starting smartd: [ OK ]
Fedora release 12 (Constantine)
Kernel 2.6.31.14-fast-20110422 on an armv6l (/dev/ttyS0)
myhostname login:
U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12)
Boot device: SATA
Attempting to set PLLA to 800 MHz ...
plla_ctrl0 : 0000030a
plla_ctrl1 : 00400000
plla_ctrl2 : 007f0068
plla_ctrl3 : 00000193
PLLA Set
Bus 0: OK
Device 0:
reading bootargs.bin
reading u-boot.img
reading u-boot.img
U-Boot 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) for OXNAS
DRAM: 128 MiB
IDE: Bus 0: OK
Device 0: Model: WDC WD1600BMVS-11F9S0 Firm: 01.01A11 Ser#: WD-WXE808KJM418
Type: Hard Disk
Supports 48-bit addressing
Capacity: 152627.8 MB = 149.0 GB (312581808 x 512)
NAND: 256 MiB
reading u-boot.env
In: serial
Out: serial
Err: serial
Net: mii0
## Error: "safeboot" not defined
Hit any key to stop autoboot: 0
4488520 bytes read in 1624 ms (2.6 MiB/s)
7033 bytes read in 59 ms (116.2 KiB/s)
magic: 0xd00dfeed
totalsize: 0x1b79 (7033)
off_dt_struct: 0x38
off_dt_strings: 0x18d4
off_mem_rsvmap: 0x28
version: 17
last_comp_version: 16
boot_cpuid_phys: 0x0
size_dt_strings: 0x2a5
size_dt_struct: 0x189c
number mem_rsv: 0x0
## Booting kernel from Legacy Image at 60000000 ...
Image Name: Linux-4.1.0-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4488456 Bytes = 4.3 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Flattened Device Tree blob at 61000000
Booting using the fdt blob at 0x61000000
Loading Kernel Image ... OK
Loading Device Tree to 67e26000, end 67e2ab78 ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.1.0-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.5
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructione
[ 0.000000] Machine model: Pogoplug Pro
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_p
[ 0.000000] Start Ox820 platform
[ 0.000000] PERCPU: Embedded 11 pages/cpu @c7edc000 s15456 r8192 d21408 u45056
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total page2
[ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/sda2 rootfst2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 120984K/131072K available (6235K kernel code, 275K rwdata,)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc07edec8 (8088 kB)
[ 0.000000] .init : 0xc07ee000 - 0xc0820000 ( 200 kB)
[ 0.000000] .data : 0xc0820000 - 0xc0864fa0 ( 276 kB)
[ 0.000000] .bss : 0xc0864fa0 - 0xc08a06a0 ( 238 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] clocksource rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffs
[ 0.000010] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 214s
[ 0.000179] Console: colour dummy device 80x30
[ 0.000209] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440)
[ 0.050032] pid_max: default: 32768 minimum: 301
[ 0.050191] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.050211] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.051082] Initializing cgroup subsys net_cls
[ 0.051148] CPU: Testing write buffer coherency: ok
[ 0.051550] Setting up static identity map for 0x60008220 - 0x60008258
[ 0.170147] Brought up 2 CPUs
[ 0.170170] SMP: Total of 2 processors activated (638.97 BogoMIPS).
[ 0.171146] devtmpfs: initialized
[ 0.176332] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_s
[ 0.176578] prandom: seed boundary self test passed
[ 0.181263] prandom: 100 self tests passed
[ 0.181294] pinctrl core: initialized pinctrl subsystem
[ 0.182174] NET: Registered protocol family 16
[ 0.182740] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.210012] cpuidle: using governor ladder
[ 0.240005] cpuidle: using governor menu
[ 0.245112] gpio-oxnas 44000000.gpio: at address c8848000
[ 0.245442] gpio-oxnas 44100000.gpio: at address c884a000
[ 0.246031] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
[ 0.259089] vgaarb: loaded
[ 0.259614] SCSI subsystem initialized
[ 0.260546] usbcore: registered new interface driver usbfs
[ 0.260659] usbcore: registered new interface driver hub
[ 0.260820] usbcore: registered new device driver usb
[ 0.261050] pps_core: LinuxPPS API ver. 1 registered
[ 0.261063] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giomet>
[ 0.261112] PTP clock support registered
[ 0.262888] cfg80211: Calling CRDA to update world regulatory domain
[ 0.263413] Switched to clocksource rps_clocksource_timer
[ 0.282613] NET: Registered protocol family 2
[ 0.283601] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.283650] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.283688] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.283791] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.283837] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.284129] NET: Registered protocol family 1
[ 0.284628] RPC: Registered named UNIX socket transport module.
[ 0.284646] RPC: Registered udp transport module.
[ 0.284659] RPC: Registered tcp transport module.
[ 0.284669] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.286484] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.286561] Initialise system trusted keyring
[ 0.300464] zpool: loaded
[ 0.300487] zbud: loaded
[ 0.306260] NFS: Registering the id_resolver key type
[ 0.306324] Key type id_resolver registered
[ 0.306339] Key type id_legacy registered
[ 0.306380] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.306403] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.307374] fuse init (API version 7.23)
[ 0.309125] Key type big_key registered
[ 0.315194] alg: No test for stdrng (krng)
[ 0.371811] Key type asymmetric registered
[ 0.371845] Asymmetric key parser 'x509' registered
[ 0.371988] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 25)
[ 0.372021] io scheduler noop registered
[ 0.372044] io scheduler deadline registered
[ 0.372413] io scheduler cfq registered (default)
[ 0.373135] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.374622] console [ttyS0] disabled
[ 0.374714] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 6, base_baud = 3906A
[ 0.903201] console [ttyS0] enabled
[ 0.917340] loop: module loaded
[ 0.922465] scsi host0: sata_oxnas
[ 0.926341] ata1: SATA max UDMA/133 irq 7
[ 0.930611] ox820sata: reseting SATA core
[ 0.931640] nand: Could not find valid ONFI parameter page; aborting
[ 0.931683] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[ 0.931688] nand: Hynix NAND 256MiB 3,3V 8-bit
[ 0.931699] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size4
[ 0.931717] Scanning device for bad blocks
[ 1.099194] 2 ofpart partitions found on MTD device 41000000.nand
[ 1.105295] Creating 2 MTD partitions on "41000000.nand":
[ 1.110691] 0x000000000000-0x000000e00000 : "boot"
[ 1.117130] 0x000000e00000-0x000008000000 : "data"
[ 1.124474] stmmaceth 40400000.ethernet: no reset control found
[ 1.130375] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 1.135431] Ring mode enabled
[ 1.138470] DMA HW capability register supported
[ 1.142988] Enhanced/Alternate descriptors
[ 1.147322] Enabled extended descriptors
[ 1.151321] RX Checksum Offload Engine supported (type 2)
[ 1.156776] TX Checksum insertion supported
[ 1.161029] Wake-Up On Lan supported
[ 1.164669] Enable RX Mitigation via HW Watchdog Timer
[ 1.173647] libphy: stmmac: probed
[ 1.177047] eth0: PHY ID 001cc914 at 0 IRQ POLL (stmmac-0:00) active
[ 1.183472] eth0: PHY ID 001cc914 at 3 IRQ POLL (stmmac-0:03)
[ 1.189296] PPP generic driver version 2.4.2
[ 1.194188] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.200737] ehci-pci: EHCI PCI platform driver
[ 1.205678] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 1.211215] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus num1
[ 1.219018] oxnas-ehci 40200100.ehci: irq 10, io mem 0x40200100
[ 1.240601] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 1.246912] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.253749] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.260958] usb usb1: Product: EHCI Host Controller
[ 1.265815] usb usb1: Manufacturer: Linux 4.1.0-oxnas-tld-1 ehci_hcd
[ 1.272151] usb usb1: SerialNumber: 40200100.ehci
[ 1.277826] hub 1-0:1.0: USB hub found
[ 1.281697] hub 1-0:1.0: 2 ports detected
[ 1.286727] usbcore: registered new interface driver cdc_acm
[ 1.292446] cdc_acm: USB Abstract Control Model driver for USB modems and ISDNs
[ 1.300625] usbcore: registered new interface driver cdc_wdm
[ 1.306442] usbcore: registered new interface driver usb-storage
[ 1.312706] usbcore: registered new interface driver usbserial
[ 1.318602] usbcore: registered new interface driver usbserial_generic
[ 1.325199] usbserial: USB Serial support registered for generic
[ 1.331624] mousedev: PS/2 mouse device common for all mice
[ 1.337346] i2c /dev entries driver
[ 1.342289] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.347924] usbcore: registered new interface driver usbhid
[ 1.353564] usbhid: USB HID core driver
[ 1.359296] NET: Registered protocol family 10
[ 1.365455] sit: IPv6 over IPv4 tunneling driver
[ 1.371333] NET: Registered protocol family 17
[ 1.375938] Key type dns_resolver registered
[ 1.381739] Loading compiled-in X.509 certificates
[ 1.390883] Key type encrypted registered
[ 1.395686] ubi0: attaching mtd1
[ 1.480015] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1.540034] ata1.00: ATA-8: WDC WD1600BMVS-11F9S0, 01.01A11, max UDMA/133
[ 1.546931] ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 1.551027] ubi0: scanning is finished
[ 1.551196] ubi0 error: ubi_read_volume_table: the layout volume was not found
[ 1.552110] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd1, error -22
[ 1.552148] UBI error: cannot attach mtd1
[ 1.576709] ata1.00: configured for UDMA/133
[ 1.581690] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BMVS-1 1A11 PQ:5
[ 1.591283] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 G)
[ 1.599779] sd 0:0:0:0: [sda] Write Protect is off
[ 1.604892] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesnA
[ 1.610644] usb 1-1: new high-speed USB device number 2 using oxnas-ehci
[ 1.626273] sda: sda1 sda2 sda3
[ 1.632250] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.644341] EXT4-fs (sda2): INFO: recovery required on readonly filesystem
[ 1.651271] EXT4-fs (sda2): write access will be enabled during recovery
[ 1.791731] EXT4-fs (sda2): recovery complete
[ 1.801228] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: ()
[ 1.808906] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[ 1.843102] devtmpfs: mounted
[ 1.846400] Freeing unused kernel memory: 200K (c07ee000 - c0820000)
[ 1.918195] usb 1-1: New USB device found, idVendor=0951, idProduct=16ae
[ 1.925030] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.932523] usb 1-1: Product: DT microDuo 3C
[ 1.936780] usb 1-1: Manufacturer: Kingston
[ 1.940974] usb 1-1: SerialNumber: 1C6F654E5981BF7069030ABF
[ 1.948487] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 1.955153] scsi host1: usb-storage 1-1:1.0
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ 3.040808] scsi 1:0:0:0: Direct-Access Kingston DT microDuo 3C PMAP PQ:6
[ 3.470092] cfg80211: Calling CRDA to update world regulatory domain
[....] Starting the hotplug events dispatcher: udevd[ 3.516549] udevd[191]: st5
. ok
[....] Synthesizing the initial hotplug events...[ 4.175774] sd 1:0:0:0: [sdb])
[ 4.224688] sd 1:0:0:0: [sdb] Write Protect is off
[ 4.231388] sd 1:0:0:0: [sdb] No Caching mode page found
[ 4.236700] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 4.306122] sdb: sdb1
[ 4.324472] sd 1:0:0:0: [sdb] Attached SCSI removable disk
done.
[....] Waiting for /dev to be fully populated...[ 5.459699] kjournald startings
[ 5.962529] EXT3-fs (sdb1): using internal journal
[ 5.967316] EXT3-fs (sdb1): recovery complete
[ 5.971681] EXT3-fs (sdb1): mounted filesystem with ordered data mode
[ 6.036234] random: nonblocking pool is initialized
udevd[313]: failed to execute '/sbin/hdparm' '/sbin/hdparm -S 120 /dev/sdb1': No y
done.
[ 6.630120] cfg80211: Calling CRDA to update world regulatory domain
[ 6.978744] EXT4-fs (sda2): re-mounted. Opts: (null)
[....] Checking root file system...fsck from util-linux 2.20.1
rootfs: clean, 27495/262144 files, 300760/1048576 blocks
done.
[ 7.309327] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[....] Cleaning up temporary files... /tmp /lib/init/rw. ok
[....] Loading kernel modules...done.
[ 9.790179] cfg80211: Calling CRDA to update world regulatory domain
[....] Activating lvm and md swap...[ 11.452720] Adding 524284k swap on /swapfiS
done.
[....] Checking file systems...fsck from util-linux 2.20.1
home was not cleanly unmounted, check forced.
[ 12.950087] cfg80211: Calling CRDA to update world regulatory domain
[ 16.120035] cfg80211: Calling CRDA to update world regulatory domain
[ 19.290050] cfg80211: Calling CRDA to update world regulatory domain
[ 22.450024] cfg80211: Calling CRDA to update world regulatory domain
[ 25.610017] cfg80211: Calling CRDA to update world regulatory domain
[ 28.770050] cfg80211: Calling CRDA to update world regulatory domain
[ 31.940037] cfg80211: Calling CRDA to update world regulatory domain
[ 35.110059] cfg80211: Exceeded CRDA call max attempts. Not calling CRDA
home: 11/9510912 files (0.0% non-contiguous), 612135/38019798 blocks
fsck died with exit status 1
done.
[....] Mounting local filesystems...done.
[....] Activating swapfile swap...done.
[....] Cleaning up temporary files.... ok
[....] Setting kernel variables ...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 42
Copyright 2004-2011 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/74:f0:6d:6a:1d:17
Sending on LPF/eth0/74:f0:6d:6a:1d:17
Sending on Socket/fallback
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 21
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
No DHCPOFFERS received.
Trying recorded lease 192.168.143.130
PING 192.168.143.1 (192.168.143.1) 56(84) bytes of data.
--- 192.168.143.1 ping statistics ---
1 packets transmitted, 0 received, 100% packet loss, time 0ms
No working leases in persistent database - sleeping.
done.
[....] Starting rpcbind daemon.... ok
[....] Starting NFS common utilities: statd idmapd. ok
[....] Cleaning up temporary files.... ok
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting NTP server: ntpd. ok
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2720 (syslogd)
. ok
[....] Starting system message bus: dbus. ok
[....] Starting NFS common utilities: statd idmapd. ok
[....] Loading cpufreq kernel modules...done (none).
[....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. ok
[....] CPUFreq Utilities: Setting ondemand CPUFreq governor...disabled, governor .
[....] Starting rpcbind daemon...[....] Already running.. ok
[....] Starting OpenBSD Secure Shell server: sshd. ok
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2721 (klogd)
. ok
[....] Not starting NFS kernel daemon: no exports. ... (warning).
Debian GNU/Linux 7 debian ttyS0
debian login:
|
Re: Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 16, 2018 12:10AM |
Admin Registered: 13 years ago Posts: 19,092 |
U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27) Boot device: NAND
|
Re: Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 16, 2018 01:42AM |
Admin Registered: 13 years ago Posts: 19,092 |
|
z0rg
Re: Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 16, 2018 02:58AM |
|
Re: Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 16, 2018 04:06AM |
Admin Registered: 13 years ago Posts: 19,092 |
U-Boot 1.1.2 (Mar 2 2011 - 10:17:22)
U-Boot code: 60D00000 -> 60D1AB60 BSS: -> 60D1F218
RAM Configuration:
Bank #0: 60000000 128 MB
SRAM Configuration:
64KB at 0x50000000
NAND:256 MiB
|
z0rg
Re: Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 16, 2018 04:25AM |
> U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27) > > Boot device: NAND >>
root@debian:~/tools# cat /etc/fw_env.config # Configuration file for fw_(printenv/saveenv) utility. # Up to two entries are valid, in this case the redundant # environment sector is assumed present. # Notice, that the "Number of sectors" is ignored on NOR. # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0x00100000 0x20000 0x20000 root@debian:~/tools# cat /proc/mtd dev: size erasesize name mtd0: 00e00000 00020000 "boot" mtd1: 07200000 00020000 "data"
root@debian:~/tools# nanddump --noecc --omitoob -f mtd0.14.01.2018fromHDD.dump /dev/mtd0 Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00e00000... root@debian:~# fw_printenv > current_envs_14.01.2018.txt Warning: Bad CRC, using default environment
root@debian:~# dmesg | grep -i 'bad' [ 0.956221] Scanning device for bad blocks
root@debian:~# cd tmp root@debian:~/tmp# tar -xf ./../uboot.2015.10-tld-2.ox820.bodhi.tar tar: uboot.2015.10-tld-2.ox820.mtd0.img: time stamp 2017-10-21 22:01:36 is 1508642663.31616384 s in the future tar: uboot.spl.2013.10.ox820.850mhz.mtd0.img: time stamp 2014-09-07 15:29:11 is 1410123118.31024512 s in the future tar: uboot.2015.10-tld-2.ox820.environment: time stamp 2017-10-22 02:40:51 is 1508659418.3084736 s in the future tar: uboot.2015.10-tld-2.ox820.environment.img: time stamp 2017-10-22 02:41:24 is 1508659451.30349696 s in the future
root@debian:~/tmp# flash_erase /dev/mtd0 0x0 6 Erasing 128 Kibyte @ a0000 -- 100 % complete
root@debian:~/tmp# nandwrite /dev/mtd0 uboot.spl.2013.10.ox820.850mhz.mtd0.img Writing data to block 0 at offset 0x0
root@debian:~/tmp# nandwrite -s 262144 /dev/mtd0 uboot.2015.10-tld-2.ox820.mtd0.img Writing data to block 2 at offset 0x40000 Writing data to block 3 at offset 0x60000 Writing data to block 4 at offset 0x80000 Writing data to block 5 at offset 0xa0000
root@debian:~/tmp# flash_erase /dev/mtd0 0x00100000 1 Erasing 128 Kibyte @ 100000 -- 100 % complete
root@debian:~/tmp# nandwrite -s 1048576 /dev/mtd0 uboot.2015.10-tld-2.ox820.environment.img Writing data to block 8 at offset 0x100000
U-Boot SPL 2013.10-tld-4 (Sep 07 2014 - 14:10:12) Boot device: NAND Attempting to set PLLA to 850 MHz ... plla_ctrl0 : 0000020a plla_ctrl1 : 00330000 plla_ctrl2 : 0065008b plla_ctrl3 : 000000f1 PLLA Setand freezes
root@debian:~# [ 3741.837975] __nand_correct_data: uncorrectable ECC error [ 5676.149752] __nand_correct_data: uncorrectable ECC error
|
Re: Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 17, 2018 03:47AM |
Admin Registered: 13 years ago Posts: 19,092 |
Quote
> root@debian:~# fw_printenv >
> current_envs_14.01.2018.txt
> Warning: Bad CRC, using default environment
> [/code]
>
> What does "Warning: Bad CRC, using default
> environment" mean? May be, are my troubles related
> with this.
Quote
> root@debian:~/tmp# tar -xf
> ./../uboot.2015.10-tld-2.ox820.bodhi.tar
> tar: uboot.2015.10-tld-2.ox820.mtd0.img: time
> stamp 2017-10-21 22:01:36 is 1508642663.31616384 s
> in the future
> tar: uboot.spl.2013.10.ox820.850mhz.mtd0.img: time
> stamp 2014-09-07 15:29:11 is 1410123118.31024512 s
> in the future
> tar: uboot.2015.10-tld-2.ox820.environment: time
> stamp 2017-10-22 02:40:51 is 1508659418.3084736 s
> in the future
> tar: uboot.2015.10-tld-2.ox820.environment.img:
> time stamp 2017-10-22 02:41:24 is
> 1508659451.30349696 s in the future
> [/code]
10th step root@debian:~/tmp# nandwrite -s 1048576 /dev/mtd0 uboot.2015.10-tld-2.ox820.environment.img Writing data to block 8 at offset 0x100000
fw_printenv
root@debian:~# [ 3741.837975] __nand_correct_data: uncorrectable ECC error [ 5676.149752] __nand_correct_data: uncorrectable ECC error
|
Re: Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 17, 2018 05:23AM |
Registered: 6 years ago Posts: 3 |
> 10th step > root@debian:~/tmp# nandwrite -s 1048576 /dev/mtd0 > uboot.2015.10-tld-2.ox820.environment.img > Writing data to block 8 at offset 0x100000 >>
> fw_printenv >
root@debian:~/tmp# fw_printenv bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm 0x60500000 0x60e00000 0x62c00000; else bootm 0x60500000 0x60e00000; fi; else if run load_dtb; then bootm 0x60500000 - 0x62c00000; else bootm 0x60500000; fi; fi bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb usb_custom_params=zswap.enabled=1 device=0:1 devices=usb ide disks=0 1 2 3 ethaddr=52:3b:20:9c:11:51 ethact=mii0 if_netconsole=ping $serverip ipaddr=192.168.0.222 serverip=192.168.0.220 dtb_file=/boot/dts/ox820-pogoplug-pro.dtb load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device 0x62c00000 $dtb_file load_initrd=echo loading uInitrd ...; load $bootdev $device 0x60e00000 /boot/uInitrd load_uimage=echo loading uImage ...; load $bootdev $device 0x60500000 /boot/uImage mainlineLinux=yes mtdids=nand0=41000000.nand mtdparts=mtdparts=41000000.nand:14m(boot),-(data) preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 0x60500000 /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_import=echo importing envs ...; env import -t 0x60510000 $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x60500000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi usb_ready_retry=15
U-Boot SPL 2013.10-tld-4 (Sep 07 2014 - 14:10:12) Boot device: NAND Attempting to set PLLA to 850 MHz ... plla_ctrl0 : 0000020a plla_ctrl1 : 00330000 plla_ctrl2 : 0065008b plla_ctrl3 : 000000f1 PLLA Set
> root@debian:~# [ 3741.837975] __nand_correct_data: > uncorrectable ECC error > [ 5676.149752] __nand_correct_data: uncorrectable > ECC error >
|
Re: Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 17, 2018 05:04PM |
Admin Registered: 13 years ago Posts: 19,092 |
|
Re: Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 17, 2018 09:44PM |
Registered: 6 years ago Posts: 3 |
U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) Boot device: SATA Attempting to set PLLA to 800 MHz ...
U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27)
Boot device: NAND
Attempting to set PLLA to 800 MHz ...
plla_ctrl0 : 0000030a
plla_ctrl1 : 00400000
plla_ctrl2 : 007f0068
plla_ctrl3 : 00000193
PLLA Set
|
Re: Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 17, 2018 09:44PM |
Registered: 6 years ago Posts: 3 |
U-Boot SPL 2013.10-ga72eb8f-dirty (Feb 19 2014 - 15:21:12) Boot device: SATA Attempting to set PLLA to 800 MHz ...
U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27)
Boot device: NAND
Attempting to set PLLA to 800 MHz ...
plla_ctrl0 : 0000030a
plla_ctrl1 : 00400000
plla_ctrl2 : 007f0068
plla_ctrl3 : 00000193
PLLA Set
|
Re: Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 19, 2018 05:16AM |
Admin Registered: 13 years ago Posts: 19,092 |
U-Boot SPL 2013.10-tld-3 ....
|
Re: Akitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) January 26, 2018 08:37AM |
Admin Registered: 13 years ago Posts: 19,092 |
> > U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27) > > Boot device: NAND > > Attempting to set PLLA to 800 MHz ... > > plla_ctrl0 : 0000030a > > plla_ctrl1 : 00400000 > > plla_ctrl2 : 007f0068 > > plla_ctrl3 : 00000193 > > > > PLLA Set >>