Re: Bricked NSA320S during 2017.07 flash March 07, 2021 04:50PM |
Admin Registered: 13 years ago Posts: 19,106 |
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10And this is an extra env, remove it to avoid confusion
usb_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi
setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params' setenv usb_boot
fdisk -l fw_printenvIf there was no error in the above, then
fw_setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params' fw_setenv usb_boot
Re: Bricked NSA320S during 2017.07 flash March 09, 2021 12:19PM |
Registered: 3 years ago Posts: 32 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06 -0700) ZyXEL NSA310S/320S 1/2-Bay Power Media Server SoC: Kirkwood 88F6702_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA3x0S> printenv arcNumber=4931 baudrate=115200 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 bootcmd=run init_sata_power; run bootcmd_uenv; run scan_disk; run set_bootargs; bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then boose if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $l bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=ttyS0,115200 device=0:1 devices=usb ide disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-nsa320s.dtb ethact=egiga0 ethaddr=4c:9e:ff:0b:73:72 if_netconsole=ping $serverip init_ide=ide reset init_mmc=mmc rescan init_sata_power=mw.l f1010104 c70e0ffd init_usb=usb start ipaddr=192.168.100.11 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $d load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /b load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /bo load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x8000 partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; ; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $dis scan_ide=ide reset scan_mmc=mmc rescan scan_usb=usb start serverip=192.168.100.127 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 start_netconsole=setenv ncip; setenv bootdelay 10; setenv stdin nc; setenv stdou stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; se uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; uenv_loaded=0 uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknu uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_re usb_ready_retry=15 Environment size: 3251/131068 bytes NSA3x0S> boot boot bootd bootefi bootelf bootm bootp bootvx bootz NSA3x0S> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: ide_preinit failed Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 30717952 00057363-01 83 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... 78 bytes read in 538 ms (0 Bytes/s) no IDE devices available importing envs ... running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 508 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 5524320 bytes read in 776 ms (6.8 MiB/s) loading uInitrd ... 9484105 bytes read in 734 ms (12.3 MiB/s) loading DTB /boot/dts/kirkwood-nsa320s.dtb ... 12586 bytes read in 1461 ms (7.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.8.3-kirkwood-tld-1 Created: 2021-02-24 12:58:54 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5524256 Bytes = 5.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.8.3-kirkwood-tld-1 Created: 2021-02-24 12:59:13 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9484041 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f200000, end 0fb0b709 ... OK Loading Device Tree to 0f1f9000, end 0f1ff129 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.8.3-kirkwood-tld-1 (root@tldDebian) (gcc [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Zyxel NSA320S [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000f [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=root0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 by [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 232740K/262144K available (10240K kernel code, 10 [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x46c/ [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Rude variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay i [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycl [ 0.000011][ T0] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps eve [ 0.000063][ T0] Switching to timer-based delay loop, resolution 6ns [ 0.000999][ T0] Console: colour dummy device 80x30 [ 0.001064][ T0] Calibrating delay loop (skipped), value calculated using [ 0.001095][ T0] pid_max: default: 32768 minimum: 301 [ 0.001595][ T0] LSM: Security Framework initializing [ 0.001771][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 byte [ 0.001806][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 [ 0.003348][ T0] CPU: Testing write buffer coherency: ok [ 0.005401][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.005770][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.006121][ T1] rcu: Hierarchical SRCU implementation. [ 0.009413][ T1] devtmpfs: initialized [ 0.017702][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffff [ 0.017746][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, lin [ 0.018088][ T1] xor: measuring software checksum speed [ 0.110149][ T1] arm4regs : 902.000 MB/sec [ 0.210101][ T1] 8regs : 541.600 MB/sec [ 0.310097][ T1] 32regs : 787.200 MB/sec [ 0.310121][ T1] xor: using function: arm4regs (902.000 MB/sec) [ 0.310149][ T1] prandom: seed boundary self test passed [ 0.315189][ T1] prandom: 100 self tests passed [ 0.315205][ T1] pinctrl core: initialized pinctrl subsystem [ 0.316274][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.317075][ T1] NET: Registered protocol family 16 [ 0.318096][ T1] DMA: preallocated 256 KiB pool for atomic coherent alloca [ 0.319182][ T1] audit: initializing netlink subsys (disabled) [ 0.321006][ T16] audit: type=2000 audit(0.310:1): state=initialized audit_ [ 0.321158][ T1] cpuidle: using governor ladder [ 0.321254][ T1] cpuidle: using governor menu [ 0.322089][ T1] Feroceon L2: Enabling L2 [ 0.322143][ T1] Feroceon L2: Cache support initialised. [ 0.335233][ T1] No ATAGs? [ 2.560069][ C0] random: fast init done [ 6.420210][ T1] raid6: int32x8 gen() 93 MB/s [ 6.590101][ T1] raid6: int32x8 xor() 58 MB/s [ 6.760278][ T1] raid6: int32x4 gen() 95 MB/s [ 6.930156][ T1] raid6: int32x4 xor() 61 MB/s [ 7.100191][ T1] raid6: int32x2 gen() 124 MB/s [ 7.270076][ T1] raid6: int32x2 xor() 75 MB/s [ 7.440259][ T1] raid6: int32x1 gen() 93 MB/s [ 7.610212][ T1] raid6: int32x1 xor() 54 MB/s [ 7.610225][ T1] raid6: using algorithm int32x2 gen() 124 MB/s [ 7.610236][ T1] raid6: .... xor() 75 MB/s, rmw enabled [ 7.610247][ T1] raid6: using intx1 recovery algorithm [ 7.610555][ T1] vgaarb: loaded [ 7.611212][ T1] SCSI subsystem initialized [ 7.611801][ T1] usbcore: registered new interface driver usbfs [ 7.611878][ T1] usbcore: registered new interface driver hub [ 7.611976][ T1] usbcore: registered new device driver usb [ 7.612203][ T1] pps_core: LinuxPPS API ver. 1 registered [ 7.612218][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodol [ 7.612249][ T1] PTP clock support registered [ 7.614298][ T1] clocksource: Switched to clocksource orion_clocksource [ 9.396470][ T1] VFS: Disk quotas dquot_6.6.0 [ 9.396588][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 [ 9.408535][ T1] NET: Registered protocol family 2 [ 9.409561][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: [ 9.409608][ T1] TCP established hash table entries: 2048 (order: 1, 8192 [ 9.409653][ T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, [ 9.409690][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 9.410198][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear [ 9.410240][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, l [ 9.410504][ T1] NET: Registered protocol family 1 [ 9.411278][ T1] RPC: Registered named UNIX socket transport module. [ 9.411294][ T1] RPC: Registered udp transport module. [ 9.411304][ T1] RPC: Registered tcp transport module. [ 9.411315][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 9.411332][ T1] PCI: CLS 0 bytes, default 32 [ 9.411706][ T1] Trying to unpack rootfs image as initramfs... [ 10.390081][ T1] Freeing initrd memory: 9264K [ 10.390532][ T1] NetWinder Floating Point Emulator V0.97 (double precision [ 10.402536][ T1] Initialise system trusted keyrings [ 10.402603][ T1] Key type blacklist registered [ 10.402852][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 10.402977][ T1] zbud: loaded [ 10.404717][ T1] NFS: Registering the id_resolver key type [ 10.404755][ T1] Key type id_resolver registered [ 10.404767][ T1] Key type id_legacy registered [ 10.404793][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering [ 10.404813][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 10.405137][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat [ 10.405651][ T1] fuse: init (API version 7.31) [ 10.406146][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 10.406399][ T1] orangefs_init: module version upstream loaded [ 10.406415][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, [ 10.528829][ T1] async_tx: api initialized (async) [ 10.528857][ T1] Key type asymmetric registered [ 10.528870][ T1] Asymmetric key parser 'x509' registered [ 10.528936][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded [ 10.529155][ T1] io scheduler bfq registered [ 10.768544][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinc [ 10.770964][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge t [ 10.770992][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 10.771011][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefff [ 10.771028][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 10.771176][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 10.771225][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pr [ 10.772905][ T1] PCI: bus0: Fast back to back transfers disabled [ 10.772938][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-0 [ 10.774533][ T1] PCI: bus1: Fast back to back transfers enabled [ 10.774565][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to [ 10.774814][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe0000 [ 10.774837][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 10.775545][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 10.835537][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor [ 10.838683][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 10.895491][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor [ 10.898939][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 10.900525][ T1] printk: console [ttyS0] disabled [ 10.900629][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base [ 11.792377][ T1] printk: console [ttyS0] enabled [ 11.806797][ T1] loop: module loaded [ 11.811309][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 11.820883][ T1] scsi host0: sata_mv [ 11.825443][ T1] scsi host1: sata_mv [ 11.829569][ T1] ata1: SATA max UDMA/133 irq 32 [ 11.834442][ T1] ata2: SATA max UDMA/133 irq 32 [ 11.840349][ T1] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1 [ 11.847506][ T1] nand: Eon NAND 128MiB 3,3V 8-bit [ 11.852455][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, [ 11.860755][ T1] Scanning device for bad blocks [ 11.870680][ T1] Bad eraseblock 100 at 0x000000c80000 [ 11.881093][ T1] Bad eraseblock 200 at 0x000001900000 [ 11.928251][ T1] 9 fixed-partitions partitions found on MTD device orion_n [ 11.935638][ T1] Creating 9 MTD partitions on "orion_nand": [ 11.941461][ T1] 0x000000000000-0x000000100000 : "uboot" [ 11.948793][ T1] 0x000000100000-0x000000180000 : "uboot_env" [ 11.956356][ T1] 0x000000180000-0x000000200000 : "key_store" [ 11.963867][ T1] 0x000000200000-0x000000280000 : "info" [ 11.970992][ T1] 0x000000280000-0x000000c80000 : "etc" [ 11.978116][ T1] 0x000000c80000-0x000001680000 : "kernel_1" [ 11.985628][ T1] 0x000001680000-0x000004640000 : "rootfs1" [ 11.993206][ T1] 0x000004640000-0x000005040000 : "kernel_2" [ 12.000751][ T1] 0x000005040000-0x000008000000 : "rootfs2" [ 12.008876][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com [ 12.017421][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Ja [ 12.029347][ T1] libphy: Fixed MDIO Bus: probed [ 12.035590][ T1] libphy: orion_mdio_bus: probed [ 12.040396][ T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-ph [ 12.070900][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version [ 12.079898][ T1] mv643xx_eth: Set the PHY to fix link down [ 12.080890][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC [ 12.096429][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Drive [ 12.103701][ T1] ehci-pci: EHCI PCI platform driver [ 12.109030][ T1] ehci-orion: EHCI orion driver [ 12.113990][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 12.120282][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigne [ 12.128873][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 12.164327][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 12.171386][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct= [ 12.180367][ T89] ata1: SATA link down (SStatus 0 SControl F300) [ 12.186557][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, Seria [ 12.194534][ T1] usb usb1: Product: EHCI Host Controller [ 12.200087][ T1] usb usb1: Manufacturer: Linux 5.8.3-kirkwood-tld-1 ehci_h [ 12.207530][ T1] usb usb1: SerialNumber: f1050000.ehci [ 12.213723][ T1] hub 1-0:1.0: USB hub found [ 12.218265][ T1] hub 1-0:1.0: 1 port detected [ 12.223704][ T1] usbcore: registered new interface driver usb-storage [ 12.230909][ T1] mousedev: PS/2 mouse device common for all mice [ 12.237569][ T1] i2c /dev entries driver [ 12.244473][ T1] ht1382 0-0068: registered as rtc0 [ 12.250584][ T1] ht1382 0-0068: setting system clock to 2021-03-09T17:51:2 [ 12.260367][ T1] device-mapper: uevent: version 1.0.3 [ 12.266041][ T1] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialis [ 12.275744][ T1] device-mapper: multipath round-robin: version 1.2.0 loade [ 12.282941][ T1] device-mapper: multipath queue-length: version 0.2.0 load [ 12.290300][ T1] device-mapper: multipath service-time: version 0.3.0 load [ 12.297719][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 12.304513][ T1] device-mapper: raid: Loading target version 1.15.1 [ 12.313608][ T1] hid: raw HID events driver (C) Jiri Kosina [ 12.319919][ T1] drop_monitor: Initializing network drop monitor service [ 12.327565][ T1] NET: Registered protocol family 10 [ 12.334118][ T1] Segment Routing with IPv6 [ 12.338537][ T1] RPL Segment Routing with IPv6 [ 12.343320][ T1] NET: Registered protocol family 17 [ 12.348729][ T1] Key type dns_resolver registered [ 12.354516][ T1] registered taskstats version 1 [ 12.359295][ T1] Loading compiled-in X.509 certificates [ 12.364949][ T1] zswap: loaded using pool lzo/zbud [ 12.370397][ T1] Key type ._fscrypt registered [ 12.375177][ T1] Key type .fscrypt registered [ 12.379777][ T1] Key type fscrypt-provisioning registered [ 12.387558][ T1] Key type big_key registered [ 12.427018][ T1] Key type encrypted registered [ 12.538322][ T91] ata2: SATA link down (SStatus 0 SControl F300) [ 12.557647][ T1] Freeing unused kernel memory: 1024K [ 12.563865][ T1] Checked W+X mappings: passed, no W+X pages found [ 12.570253][ T1] Run /init as init process [ 12.584417][ T100] usb 1-1: new high-speed USB device number 2 using orion-e Loading, please wait... Starting version 241 [ 12.786272][ T100] usb 1-1: New USB device found, idVendor=05e3, idProduct=0 [ 12.804411][ T100] usb 1-1: New USB device strings: Mfr=0, Product=1, Serial [ 12.812214][ T100] usb 1-1: Product: USB2.0 Hub [ 12.843914][ T100] hub 1-1:1.0: USB hub found [ 12.854595][ T100] hub 1-1:1.0: 4 ports detected [ 13.184402][ T100] usb 1-1.1: new high-speed USB device number 3 using orion [ 13.518539][ T100] usb 1-1.1: New USB device found, idVendor=0951, idProduct [ 13.544525][ T100] usb 1-1.1: New USB device strings: Mfr=1, Product=2, Seri [ 13.552528][ T100] usb 1-1.1: Product: DataTraveler 2.0 [ 13.582603][ T100] usb 1-1.1: Manufacturer: Kingston [ 13.595530][ T100] usb 1-1.1: SerialNumber: 00241D8CE55DBE50595760E4 [ 13.619576][ T100] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 13.649129][ T100] scsi host2: usb-storage 1-1.1:1.0 [ 14.012072][ T129] usbcore: registered new interface driver uas [ 15.211874][ T58] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 [ 15.227451][ T7] sd 2:0:0:0: [sda] 30720000 512-byte logical blocks: (15.7 [ 15.242564][ T7] sd 2:0:0:0: [sda] Write Protect is off [ 15.249291][ T7] sd 2:0:0:0: [sda] No Caching mode page found [ 15.255354][ T7] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 15.270540][ T7] sda: sda1 [ 15.288565][ T7] sd 2:0:0:0: [sda] Attached SCSI removable disk Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 26.606594][ T152] process '/usr/bin/fstype' started with executable stack Begin: Will now check root file system ... fsck from util-linux 2.33.1 [/sbin/fsck.ext4 (1) -- /dev/sda1] fsck.ext4 -a -C0 /dev/sda1 rootfs: clean, 26084/960992 files, 429236/3839744 blocks done. [ 32.907829][ T161] EXT4-fs (sda1): mounted filesystem with ordered data mode done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Starting hotplug events dispatcher: systemd-udevd. [ ok ] Synthesizing the initial hotplug events (subsystems)...done. [....] Synthesizing the initial hotplug events (devices)...[ 37.250687][ T349] input: gpio_keys as /devices/platform/gpio_keys/input/input0 done. [....] Waiting for /dev to be fully populated...[ 37.737729][ T368] systemd-udevd[368]: Using default interface naming scheme 'v240'. [ 37.873376][ T368] systemd-udevd[368]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 37.941186][ T377] orion_wdt: Initial timeout 25 sec [ 38.405027][ C0] random: crng init done [ 38.426368][ T356] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 38.543361][ T350] marvell-cesa f1030000.crypto: CESA device successfully registered [ 38.719835][ T349] systemd-udevd[349]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. done. [ ok ] Setting hostname to 'debian'...done. [ ok ] Activating swap:. [ 41.272971][ T575] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [info] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs[ ok hat location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Starting Setting kernel variables: sysctl. [ ok ] Initializing random number generator...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/4c:9e:ff:0b:73:72 Sending on LPF/eth0/4c:9e:ff:0b:73:72 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 [ 46.229486][ T1099] mv643xx_eth: Set the PHY back to auto-negotiation mode [ 48.081256][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled [ 48.098548][ T100] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15 DHCPOFFER of 192.168.100.11 from 192.168.100.100 DHCPREQUEST for 192.168.100.11 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.100.11 from 192.168.100.100 invoke-rc.d: could not determine current runlevel Reloading /etc/samba/smb.conf: smbd. bound to 192.168.100.11 -- renewal in 532171319 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... [....] Setting sensors limits...No sensors found! Make sure you loaded all the kernel drivers you need. Try sensors-detect to find out which these are. No sensors found! Make sure you loaded all the kernel drivers you need. Try sensors-detect to find out which these are. done. INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1363 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1390 (klogd) . ok [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [....] Starting a multimedia keyboard daemon for Linux : esekeydESE Key Deamon 1.2.7 (SVN-r63) Segmentation fault failed! [ ok ] Starting MTA: exim4. [warn] Not starting fancontrol; run pwmconfig first. ... (warning). [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NetBIOS name server: nmbd. [ ok ] Starting NTP server: ntpd. [....] Not starting S.M.A.R.T. daemon smartd, disabled via /etc/default/smartmon[warn ... (warning). [ ok ] Starting SMB/CIFS daemon: smbd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Running local boot scripts (/etc/rc.local). [FAIL] startpar: service(s) returned failure: esekeyd ... failed! Debian GNU/Linux 10 debian ttyS0 debian login: root Password: Last login: Tue Mar 9 18:49:20 CET 2021 on ttyS0 Linux debian 5.8.3-kirkwood-tld-1 #1.0 PREEMPT Sat Aug 22 16:10:01 PDT 2020 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# fdisk -l Disk /dev/mtdblock0: 1 MiB, 1048576 bytes, 2048 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/mtdblock1: 512 KiB, 524288 bytes, 1024 se[ 121.613805][ T2080] __nand_correct_data: uncorrectable ECC error ctors Units[ 121.620326][ T2080] __nand_correct_data: uncorrectable ECC error : sectors of 1 *[ 121.628071][ T2080] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 512 = 512 bytes[ 121.640776][ T2080] __nand_correct_data: uncorrectable ECC error Sector size (l[ 121.647956][ T2080] __nand_correct_data: uncorrectable ECC error ogical/physical)[ 121.655339][ T2080] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 : 512 bytes / 51[ 121.667737][ T2080] Buffer I/O error on dev mtdblock5, logical block 0, async page read 2 bytes I/O siz[ 121.677314][ T2080] __nand_correct_data: uncorrectable ECC error e (minimum/optim[ 121.684257][ T2080] __nand_correct_data: uncorrectable ECC error al): 512 bytes /[ 121.691954][ T2080] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 512 bytes [ 121.704257][ T2080] Buffer I/O error on dev mtdblock5, logical block 0, async page read Disk /dev/mtdblock2: 512 KiB, 524288 bytes, 1024 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/mtdblock3: 512 KiB, 524288 bytes, 1024 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/mtdblock4: 10 MiB, 10485760 bytes, 20480 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/mtdblock6: 47.8 MiB, 50069504 bytes, 97792 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/mtdblock7: 10 MiB, 10485760 bytes, 20480 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/mtdblock8: 47.8 MiB, 50069504 bytes, 97792 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/sda: 14.7 GiB, 15728640000 bytes, 30720000 sectors Disk model: DataTraveler 2.0 Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x00057363 Device Boot Start End Sectors Size Id Type /dev/sda1 2048 30719999 30717952 14.7G 83 Linux root@debian:~# fw_printenv arcNumber=4931 baudrate=115200 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 bootcmd=run init_sata_power; run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=ttyS0,115200 device=0:1 devices=usb ide disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-nsa320s.dtb ethact=egiga0 ethaddr=4c:9e:ff:0b:73:72 if_netconsole=ping $serverip init_ide=ide reset init_mmc=mmc rescan init_sata_power=mw.l f1010104 c70e0ffd init_usb=usb start ipaddr=192.168.100.11 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done scan_ide=ide reset scan_mmc=mmc rescan scan_usb=usb start serverip=192.168.100.127 start_netconsole=setenv ncip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_loaded=0 uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params root@debian:~#
Re: Bricked NSA320S during 2017.07 flash March 09, 2021 07:21PM |
Admin Registered: 13 years ago Posts: 19,106 |
Re: Bricked NSA320S during 2017.07 flash March 10, 2021 04:24PM |
Registered: 3 years ago Posts: 32 |
NSA3x0S> usb start starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found NSA3x0S> usb tree USB device tree: 1 Hub (480 Mb/s, 0mA) | u-boot EHCI Host Controller | +-2 Hub (480 Mb/s, 100mA) | USB2.0 Hub | +-3 Mass Storage (480 Mb/s, 200mA) Kingston DataTraveler 2.0 00241D8CE55DBE50595760E4 NSA3x0S> usb info 1: Hub, USB Revision 2.0 - u-boot EHCI Host Controller - Class: Hub - PacketSize: 64 Configurations: 1 - Vendor: 0x0000 Product 0x0000 Version 1.0 Configuration: 1 - Interfaces: 1 Self Powered 0mA Interface: 0 - Alternate Setting 0, Endpoints: 1 - Class Hub - Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms 2: Hub, USB Revision 2.0 - USB2.0 Hub - Class: Hub - PacketSize: 64 Configurations: 1 - Vendor: 0x05e3 Product 0x0608 Version 133.50 Configuration: 1 - Interfaces: 1 Self Powered Remote Wakeup 100mA Interface: 0 - Alternate Setting 0, Endpoints: 1 - Class Hub - Endpoint 1 In Interrupt MaxPacket 1 Interval 12ms 3: Mass Storage, USB Revision 2.0 - Kingston DataTraveler 2.0 00241D8CE55DBE50595760E4 - Class: (from Interface) Mass Storage - PacketSize: 64 Configurations: 1 - Vendor: 0x0951 Product 0x1665 Version 1.0 Configuration: 1 - Interfaces: 1 Bus Powered 200mA Interface: 0 - Alternate Setting 0, Endpoints: 2 - Class Mass Storage, Transp. SCSI, Bulk only - Endpoint 1 In Bulk MaxPacket 512 - Endpoint 2 Out Bulk MaxPacket 512
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06 -0700) ZyXEL NSA310S/320S 1/2-Bay Power Media Server SoC: Kirkwood 88F6702_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: WDC WD10EAVS-00D7B0 Firm: 01.01A01 Ser#: WD-WCAU41984981 Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 30717952 00057363-01 83 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... 70 bytes read in 538 ms (0 Bytes/s) Partition Map for IDE device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 1953523120 ec2d0c47-01 83 importing envs ... running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 508 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 5524320 bytes read in 777 ms (6.8 MiB/s) loading uInitrd ... 9484105 bytes read in 735 ms (12.3 MiB/s) loading DTB /boot/dts/kirkwood-nsa320s.dtb ... 12586 bytes read in 1461 ms (7.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.8.3-kirkwood-tld-1 Created: 2021-02-24 12:58:54 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5524256 Bytes = 5.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.8.3-kirkwood-tld-1 Created: 2021-02-24 12:59:13 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9484041 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f200000, end 0fb0b709 ... OK Loading Device Tree to 0f1f9000, end 0f1ff129 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.8.3-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Aug 22 16:10:01 PDT 2020 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Zyxel NSA320S [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 232740K/262144K available (10240K kernel code, 1085K rwdata, 4108K rodata, 1024K init, 298K bss, 29404K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x46c/0x808 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Rude variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000011][ T0] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000063][ T0] Switching to timer-based delay loop, resolution 6ns [ 0.000999][ T0] Console: colour dummy device 80x30 [ 0.001064][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.001095][ T0] pid_max: default: 32768 minimum: 301 [ 0.001595][ T0] LSM: Security Framework initializing [ 0.001771][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001806][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003348][ T0] CPU: Testing write buffer coherency: ok [ 0.005406][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.005774][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.006123][ T1] rcu: Hierarchical SRCU implementation. [ 0.009413][ T1] devtmpfs: initialized [ 0.017670][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.017714][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.018058][ T1] xor: measuring software checksum speed [ 0.110147][ T1] arm4regs : 902.000 MB/sec [ 0.210101][ T1] 8regs : 541.600 MB/sec [ 0.310099][ T1] 32regs : 787.200 MB/sec [ 0.310123][ T1] xor: using function: arm4regs (902.000 MB/sec) [ 0.310151][ T1] prandom: seed boundary self test passed [ 0.315191][ T1] prandom: 100 self tests passed [ 0.315205][ T1] pinctrl core: initialized pinctrl subsystem [ 0.316268][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.317067][ T1] NET: Registered protocol family 16 [ 0.318088][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.319179][ T1] audit: initializing netlink subsys (disabled) [ 0.321003][ T16] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 [ 0.321151][ T1] cpuidle: using governor ladder [ 0.321249][ T1] cpuidle: using governor menu [ 0.322082][ T1] Feroceon L2: Enabling L2 [ 0.322136][ T1] Feroceon L2: Cache support initialised. [ 0.335222][ T1] No ATAGs? [ 2.560069][ C0] random: fast init done [ 6.420231][ T1] raid6: int32x8 gen() 93 MB/s [ 6.590213][ T1] raid6: int32x8 xor() 58 MB/s [ 6.760151][ T1] raid6: int32x4 gen() 95 MB/s [ 6.930172][ T1] raid6: int32x4 xor() 61 MB/s [ 7.100261][ T1] raid6: int32x2 gen() 123 MB/s [ 7.270145][ T1] raid6: int32x2 xor() 75 MB/s [ 7.440172][ T1] raid6: int32x1 gen() 93 MB/s [ 7.610152][ T1] raid6: int32x1 xor() 55 MB/s [ 7.610165][ T1] raid6: using algorithm int32x2 gen() 123 MB/s [ 7.610176][ T1] raid6: .... xor() 75 MB/s, rmw enabled [ 7.610186][ T1] raid6: using intx1 recovery algorithm [ 7.610492][ T1] vgaarb: loaded [ 7.611146][ T1] SCSI subsystem initialized [ 7.611735][ T1] usbcore: registered new interface driver usbfs [ 7.611814][ T1] usbcore: registered new interface driver hub [ 7.611911][ T1] usbcore: registered new device driver usb [ 7.612139][ T1] pps_core: LinuxPPS API ver. 1 registered [ 7.612152][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 7.612184][ T1] PTP clock support registered [ 7.614228][ T1] clocksource: Switched to clocksource orion_clocksource [ 9.397046][ T1] VFS: Disk quotas dquot_6.6.0 [ 9.397163][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 9.409119][ T1] NET: Registered protocol family 2 [ 9.410149][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 9.410196][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 9.410241][ T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 9.410279][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 9.410785][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 9.410828][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 9.411095][ T1] NET: Registered protocol family 1 [ 9.411863][ T1] RPC: Registered named UNIX socket transport module. [ 9.411880][ T1] RPC: Registered udp transport module. [ 9.411891][ T1] RPC: Registered tcp transport module. [ 9.411901][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 9.411918][ T1] PCI: CLS 0 bytes, default 32 [ 9.412293][ T1] Trying to unpack rootfs image as initramfs... [ 10.390350][ T1] Freeing initrd memory: 9264K [ 10.390801][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 10.402814][ T1] Initialise system trusted keyrings [ 10.402889][ T1] Key type blacklist registered [ 10.403143][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 10.403268][ T1] zbud: loaded [ 10.405057][ T1] NFS: Registering the id_resolver key type [ 10.405100][ T1] Key type id_resolver registered [ 10.405111][ T1] Key type id_legacy registered [ 10.405137][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 10.405158][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 10.405480][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 10.405994][ T1] fuse: init (API version 7.31) [ 10.406456][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 10.406707][ T1] orangefs_init: module version upstream loaded [ 10.406722][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 10.527846][ T1] async_tx: api initialized (async) [ 10.527874][ T1] Key type asymmetric registered [ 10.527885][ T1] Asymmetric key parser 'x509' registered [ 10.527951][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 10.528170][ T1] io scheduler bfq registered [ 10.767513][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 10.769946][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 10.769974][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 10.769993][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 10.770011][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 10.770158][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 10.770207][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 10.771883][ T1] PCI: bus0: Fast back to back transfers disabled [ 10.771918][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 10.773443][ T1] PCI: bus1: Fast back to back transfers enabled [ 10.773475][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 10.773723][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref] [ 10.773745][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 10.774519][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 10.835454][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 10.838600][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 10.895425][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 10.898872][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 10.900454][ T1] printk: console [ttyS0] disabled [ 10.900559][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 10416666) is a 16550A [ 11.792315][ T1] printk: console [ttyS0] enabled [ 11.806714][ T1] loop: module loaded [ 11.811230][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 11.820795][ T1] scsi host0: sata_mv [ 11.825352][ T1] scsi host1: sata_mv [ 11.829472][ T1] ata1: SATA max UDMA/133 irq 32 [ 11.834344][ T1] ata2: SATA max UDMA/133 irq 32 [ 11.840248][ T1] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1 [ 11.847406][ T1] nand: Eon NAND 128MiB 3,3V 8-bit [ 11.852357][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 11.860657][ T1] Scanning device for bad blocks [ 11.870581][ T1] Bad eraseblock 100 at 0x000000c80000 [ 11.880996][ T1] Bad eraseblock 200 at 0x000001900000 [ 11.928182][ T1] 9 fixed-partitions partitions found on MTD device orion_nand [ 11.935576][ T1] Creating 9 MTD partitions on "orion_nand": [ 11.941396][ T1] 0x000000000000-0x000000100000 : "uboot" [ 11.948730][ T1] 0x000000100000-0x000000180000 : "uboot_env" [ 11.956294][ T1] 0x000000180000-0x000000200000 : "key_store" [ 11.963809][ T1] 0x000000200000-0x000000280000 : "info" [ 11.970926][ T1] 0x000000280000-0x000000c80000 : "etc" [ 11.978034][ T1] 0x000000c80000-0x000001680000 : "kernel_1" [ 11.985550][ T1] 0x000001680000-0x000004640000 : "rootfs1" [ 11.993132][ T1] 0x000004640000-0x000005040000 : "kernel_2" [ 12.000674][ T1] 0x000005040000-0x000008000000 : "rootfs2" [ 12.008792][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 12.017332][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 12.029261][ T1] libphy: Fixed MDIO Bus: probed [ 12.035499][ T1] libphy: orion_mdio_bus: probed [ 12.040307][ T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@1: Whitelisted compatible string. Please remove [ 12.070698][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 12.079699][ T1] mv643xx_eth: Set the PHY to fix link down [ 12.080694][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 4c:9e:ff:0b:73:72 [ 12.096239][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.103509][ T1] ehci-pci: EHCI PCI platform driver [ 12.108834][ T1] ehci-orion: EHCI orion driver [ 12.113796][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 12.120088][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 12.128682][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 12.164257][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 12.171315][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08 [ 12.180350][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.188264][ T1] usb usb1: Product: EHCI Host Controller [ 12.193819][ T1] usb usb1: Manufacturer: Linux 5.8.3-kirkwood-tld-1 ehci_hcd [ 12.201118][ T1] usb usb1: SerialNumber: f1050000.ehci [ 12.207286][ T1] hub 1-0:1.0: USB hub found [ 12.211765][ T1] hub 1-0:1.0: 1 port detected [ 12.217272][ T1] usbcore: registered new interface driver usb-storage [ 12.224477][ T1] mousedev: PS/2 mouse device common for all mice [ 12.231043][ T1] i2c /dev entries driver [ 12.237970][ T1] ht1382 0-0068: registered as rtc0 [ 12.244084][ T1] ht1382 0-0068: setting system clock to 2021-03-10T13:40:17 UTC (1615383617) [ 12.253846][ T1] device-mapper: uevent: version 1.0.3 [ 12.259554][ T1] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com [ 12.269242][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 12.276520][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 12.283803][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 12.291214][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 12.298008][ T1] device-mapper: raid: Loading target version 1.15.1 [ 12.307133][ T1] hid: raw HID events driver (C) Jiri Kosina [ 12.313384][ T1] drop_monitor: Initializing network drop monitor service [ 12.320900][ T1] NET: Registered protocol family 10 [ 12.327643][ T1] Segment Routing with IPv6 [ 12.331986][ T1] RPL Segment Routing with IPv6 [ 12.336844][ T1] NET: Registered protocol family 17 [ 12.342222][ T1] Key type dns_resolver registered [ 12.347244][ T89] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 12.355161][ T1] registered taskstats version 1 [ 12.360234][ T1] Loading compiled-in X.509 certificates [ 12.366010][ T1] zswap: loaded using pool lzo/zbud [ 12.371463][ T1] Key type ._fscrypt registered [ 12.376249][ T1] Key type .fscrypt registered [ 12.380845][ T1] Key type fscrypt-provisioning registered [ 12.388643][ T1] Key type big_key registered [ 12.428636][ T1] Key type encrypted registered [ 12.584264][ T100] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 12.786200][ T100] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.32 [ 12.795200][ T100] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 12.803030][ T100] usb 1-1: Product: USB2.0 Hub [ 12.808645][ T100] hub 1-1:1.0: USB hub found [ 12.813444][ T100] hub 1-1:1.0: 4 ports detected [ 13.124340][ T89] ata1.00: ATA-8: WDC WD10EAVS-00D7B0, 01.01A01, max UDMA/133 [ 13.131625][ T89] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 13.143851][ T89] ata1.00: configured for UDMA/133 [ 13.159411][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD10EAVS-00D 1A01 PQ: 0 ANSI: 5 [ 13.169577][ T93] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 13.178555][ T93] sd 0:0:0:0: [sda] Write Protect is off [ 13.184213][ T93] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 13.202622][ T93] sda: sda1 [ 13.207440][ T93] sd 0:0:0:0: [sda] Attached SCSI disk [ 13.505937][ T91] ata2: SATA link down (SStatus 0 SControl F300) [ 13.525249][ T1] Freeing unused kernel memory: 1024K [ 13.531463][ T1] Checked W+X mappings: passed, no W+X pages found [ 13.537851][ T1] Run /init as init process Loading, please wait... Starting version 241 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 26.476500][ T148] __nand_correct_data: uncorrectable ECC error [ 26.482493][ T148] __nand_correct_data: uncorrectable ECC error [ 26.488561][ T148] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 26.500179][ T148] __nand_correct_data: uncorrectable ECC error [ 26.506196][ T148] __nand_correct_data: uncorrectable ECC error [ 26.512189][ T148] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 26.523210][ T148] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 27.764977][ T148] __nand_correct_data: uncorrectable ECC error [ 27.770969][ T148] __nand_correct_data: uncorrectable ECC error [ 27.777029][ T148] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 27.788645][ T148] __nand_correct_data: uncorrectable ECC error [ 27.794662][ T148] __nand_correct_data: uncorrectable ECC error [ 27.800654][ T148] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 27.811675][ T148] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done. [ 29.335938][ T152] __nand_correct_data: uncorrectable ECC error [ 29.341927][ T152] __nand_correct_data: uncorrectable ECC error [ 29.347992][ T152] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 29.359603][ T152] __nand_correct_data: uncorrectable ECC error [ 29.365612][ T152] __nand_correct_data: uncorrectable ECC error [ 29.371606][ T152] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 29.382625][ T152] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 29.880451][ T152] __nand_correct_data: uncorrectable ECC error [ 29.886555][ T152] __nand_correct_data: uncorrectable ECC error [ 29.892548][ T152] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 29.904146][ T152] __nand_correct_data: uncorrectable ECC error [ 29.910214][ T152] __nand_correct_data: uncorrectable ECC error [ 29.916228][ T152] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 29.927288][ T152] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 31.647064][ T156] __nand_correct_data: uncorrectable ECC error [ 31.653059][ T156] __nand_correct_data: uncorrectable ECC error [ 31.659126][ T156] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 31.670744][ T156] __nand_correct_data: uncorrectable ECC error [ 31.676761][ T156] __nand_correct_data: uncorrectable ECC error [ 31.682753][ T156] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 31.693774][ T156] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 32.191943][ T156] __nand_correct_data: uncorrectable ECC error [ 32.198049][ T156] __nand_correct_data: uncorrectable ECC error [ 32.204042][ T156] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 32.215642][ T156] __nand_correct_data: uncorrectable ECC error [ 32.221621][ T156] __nand_correct_data: uncorrectable ECC error [ 32.227699][ T156] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 32.238728][ T156] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 33.958197][ T160] __nand_correct_data: uncorrectable ECC error [ 33.964189][ T160] __nand_correct_data: uncorrectable ECC error [ 33.970279][ T160] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 33.981870][ T160] __nand_correct_data: uncorrectable ECC error [ 33.987940][ T160] __nand_correct_data: uncorrectable ECC error [ 33.993928][ T160] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 34.004953][ T160] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 34.503294][ T160] __nand_correct_data: uncorrectable ECC error [ 34.509396][ T160] __nand_correct_data: uncorrectable ECC error [ 34.515447][ T160] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 34.527059][ T160] __nand_correct_data: uncorrectable ECC error [ 34.533045][ T160] __nand_correct_data: uncorrectable ECC error [ 34.539065][ T160] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 34.550089][ T160] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 36.269053][ T164] __nand_correct_data: uncorrectable ECC error [ 36.275149][ T164] __nand_correct_data: uncorrectable ECC error [ 36.281145][ T164] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 36.292741][ T164] __nand_correct_data: uncorrectable ECC error [ 36.298810][ T164] __nand_correct_data: uncorrectable ECC error [ 36.304826][ T164] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 36.315853][ T164] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 36.813700][ T164] __nand_correct_data: uncorrectable ECC error [ 36.819801][ T164] __nand_correct_data: uncorrectable ECC error [ 36.825854][ T164] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 36.837472][ T164] __nand_correct_data: uncorrectable ECC error [ 36.843450][ T164] __nand_correct_data: uncorrectable ECC error [ 36.849470][ T164] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 36.860494][ T164] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 38.580082][ T168] __nand_correct_data: uncorrectable ECC error [ 38.586191][ T168] __nand_correct_data: uncorrectable ECC error [ 38.592182][ T168] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 38.603781][ T168] __nand_correct_data: uncorrectable ECC error [ 38.609846][ T168] __nand_correct_data: uncorrectable ECC error [ 38.615862][ T168] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 38.626890][ T168] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 39.124923][ T168] __nand_correct_data: uncorrectable ECC error [ 39.130918][ T168] __nand_correct_data: uncorrectable ECC error [ 39.136980][ T168] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 39.148594][ T168] __nand_correct_data: uncorrectable ECC error [ 39.154603][ T168] __nand_correct_data: uncorrectable ECC error [ 39.160595][ T168] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 39.171617][ T168] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 40.891525][ T172] __nand_correct_data: uncorrectable ECC error [ 40.897628][ T172] __nand_correct_data: uncorrectable ECC error [ 40.903623][ T172] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 40.915223][ T172] __nand_correct_data: uncorrectable ECC error [ 40.921203][ T172] __nand_correct_data: uncorrectable ECC error [ 40.927280][ T172] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 40.938308][ T172] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 41.436748][ T172] __nand_correct_data: uncorrectable ECC error [ 41.442740][ T172] __nand_correct_data: uncorrectable ECC error [ 41.448804][ T172] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 41.460415][ T172] __nand_correct_data: uncorrectable ECC error [ 41.466425][ T172] __nand_correct_data: uncorrectable ECC error [ 41.472418][ T172] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 41.483438][ T172] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 43.202202][ T176] __nand_correct_data: uncorrectable ECC error [ 43.208306][ T176] __nand_correct_data: uncorrectable ECC error [ 43.214365][ T176] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 43.225987][ T176] __nand_correct_data: uncorrectable ECC error [ 43.231971][ T176] __nand_correct_data: uncorrectable ECC error [ 43.237987][ T176] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 43.249014][ T176] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 43.747248][ T176] __nand_correct_data: uncorrectable ECC error [ 43.753241][ T176] __nand_correct_data: uncorrectable ECC error [ 43.759315][ T176] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 43.770953][ T176] __nand_correct_data: uncorrectable ECC error [ 43.776968][ T176] __nand_correct_data: uncorrectable ECC error [ 43.782961][ T176] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 43.793982][ T176] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 45.513223][ T180] __nand_correct_data: uncorrectable ECC error [ 45.519323][ T180] __nand_correct_data: uncorrectable ECC error [ 45.525376][ T180] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 45.536993][ T180] __nand_correct_data: uncorrectable ECC error [ 45.542981][ T180] __nand_correct_data: uncorrectable ECC error [ 45.549000][ T180] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 45.560025][ T180] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 46.058194][ T180] __nand_correct_data: uncorrectable ECC error [ 46.064189][ T180] __nand_correct_data: uncorrectable ECC error [ 46.070284][ T180] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 46.081879][ T180] __nand_correct_data: uncorrectable ECC error [ 46.087951][ T180] __nand_correct_data: uncorrectable ECC error [ 46.093946][ T180] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 46.104971][ T180] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 46.589564][ C0] random: crng init done Begin: Running /scripts/local-block ... done. [ 47.824444][ T184] __nand_correct_data: uncorrectable ECC error [ 47.830439][ T184] __nand_correct_data: uncorrectable ECC error [ 47.836493][ T184] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 47.848107][ T184] __nand_correct_data: uncorrectable ECC error [ 47.854094][ T184] __nand_correct_data: uncorrectable ECC error [ 47.860112][ T184] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 47.871136][ T184] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 48.369255][ T184] __nand_correct_data: uncorrectable ECC error [ 48.375361][ T184] __nand_correct_data: uncorrectable ECC error [ 48.381353][ T184] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 48.392951][ T184] __nand_correct_data: uncorrectable ECC error [ 48.399021][ T184] __nand_correct_data: uncorrectable ECC error [ 48.405041][ T184] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 48.416061][ T184] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 50.135517][ T188] __nand_correct_data: uncorrectable ECC error [ 50.141509][ T188] __nand_correct_data: uncorrectable ECC error [ 50.147572][ T188] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 50.159186][ T188] __nand_correct_data: uncorrectable ECC error [ 50.165194][ T188] __nand_correct_data: uncorrectable ECC error [ 50.171188][ T188] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 50.182208][ T188] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 50.680304][ T188] __nand_correct_data: uncorrectable ECC error [ 50.686406][ T188] __nand_correct_data: uncorrectable ECC error [ 50.692398][ T188] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 50.703997][ T188] __nand_correct_data: uncorrectable ECC error [ 50.710064][ T188] __nand_correct_data: uncorrectable ECC error [ 50.716079][ T188] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 50.727107][ T188] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 52.446672][ T192] __nand_correct_data: uncorrectable ECC error [ 52.452666][ T192] __nand_correct_data: uncorrectable ECC error [ 52.458731][ T192] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 52.470349][ T192] __nand_correct_data: uncorrectable ECC error [ 52.476359][ T192] __nand_correct_data: uncorrectable ECC error [ 52.482353][ T192] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 52.493373][ T192] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 52.991397][ T192] __nand_correct_data: uncorrectable ECC error [ 52.997501][ T192] __nand_correct_data: uncorrectable ECC error [ 53.003494][ T192] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 53.015096][ T192] __nand_correct_data: uncorrectable ECC error [ 53.021082][ T192] __nand_correct_data: uncorrectable ECC error [ 53.027159][ T192] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 53.038187][ T192] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 54.757761][ T196] __nand_correct_data: uncorrectable ECC error [ 54.763754][ T196] __nand_correct_data: uncorrectable ECC error [ 54.769839][ T196] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 54.781474][ T196] __nand_correct_data: uncorrectable ECC error [ 54.787491][ T196] __nand_correct_data: uncorrectable ECC error [ 54.793483][ T196] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 54.804505][ T196] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 55.302699][ T196] __nand_correct_data: uncorrectable ECC error [ 55.308805][ T196] __nand_correct_data: uncorrectable ECC error [ 55.314858][ T196] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 55.326476][ T196] __nand_correct_data: uncorrectable ECC error [ 55.332463][ T196] __nand_correct_data: uncorrectable ECC error [ 55.338482][ T196] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 55.349506][ T196] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 57.068312][ T200] __nand_correct_data: uncorrectable ECC error [ 57.074411][ T200] __nand_correct_data: uncorrectable ECC error [ 57.080408][ T200] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 57.092005][ T200] __nand_correct_data: uncorrectable ECC error [ 57.098074][ T200] __nand_correct_data: uncorrectable ECC error [ 57.104062][ T200] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 57.115086][ T200] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 57.613250][ T200] __nand_correct_data: uncorrectable ECC error [ 57.619345][ T200] __nand_correct_data: uncorrectable ECC error [ 57.625402][ T200] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 57.637019][ T200] __nand_correct_data: uncorrectable ECC error [ 57.642998][ T200] __nand_correct_data: uncorrectable ECC error [ 57.649016][ T200] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 57.660042][ T200] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 59.379617][ T204] __nand_correct_data: uncorrectable ECC error [ 59.385716][ T204] __nand_correct_data: uncorrectable ECC error [ 59.391711][ T204] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 59.403312][ T204] __nand_correct_data: uncorrectable ECC error [ 59.409380][ T204] __nand_correct_data: uncorrectable ECC error [ 59.415401][ T204] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 59.426428][ T204] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 59.924444][ T204] __nand_correct_data: uncorrectable ECC error [ 59.930440][ T204] __nand_correct_data: uncorrectable ECC error [ 59.936493][ T204] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 59.948108][ T204] __nand_correct_data: uncorrectable ECC error [ 59.954095][ T204] __nand_correct_data: uncorrectable ECC error [ 59.960114][ T204] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 59.971138][ T204] Buffer I/O error on dev mtdblock5, logical block 0, async page read done. [ 60.676732][ T206] __nand_correct_data: uncorrectable ECC error [ 60.682724][ T206] __nand_correct_data: uncorrectable ECC error [ 60.688790][ T206] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 60.700408][ T206] __nand_correct_data: uncorrectable ECC error [ 60.706418][ T206] __nand_correct_data: uncorrectable ECC error [ 60.712410][ T206] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 60.723431][ T206] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 61.221597][ T206] __nand_correct_data: uncorrectable ECC error [ 61.227699][ T206] __nand_correct_data: uncorrectable ECC error [ 61.233691][ T206] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 61.245292][ T206] __nand_correct_data: uncorrectable ECC error [ 61.251277][ T206] __nand_correct_data: uncorrectable ECC error [ 61.257355][ T206] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 61.268383][ T206] Buffer I/O error on dev mtdblock5, logical block 0, async page read Gave up waiting for root file system device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Missing modules (cat /proc/modules; ls /dev) ALERT! LABEL=rootfs does not exist. Dropping to a shell! BusyBox v1.30.1 (Debian 1:1.30.1-4) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs)
Re: Bricked NSA320S during 2017.07 flash March 10, 2021 05:10PM |
Admin Registered: 13 years ago Posts: 19,106 |
Quote
1. With only the USB rootfs plugged in. Power up, interrupt serial console and
setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params'
setenv usb_boot
Boot all the way into Debian and then, do
fdisk -l
fw_printenv
If there was no error in the above, then
fw_setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params'
fw_setenv usb_boot
And then reboot and let the box boot with interrupting it. Once you can reboot a few times, the we know all is well.
Quote
2. After Step 1 above was done OK. Shutdown the box and insert the HDD into slot 1.
Boot and verify that the HDD can be access. And dont do step 3 below yet until you can see the HDD 1 is functioning well. IOW, try to copy some large files from the USB rootfs to the HDD... so on.
setenv mtdparts 'mtdparts=orion_nand:0x100000(uboot)'(The above is to hide the rest of the mtd partitions from the kernel, just expose mtd0)
boot
fw_setenv mtdparts 'mtdparts=orion_nand:0x100000(uboot)'Since we are booting with rootfs on USB/HDD, the only parttion needed is mtd0. In the future, should you want to use the other mtds for storing OpenWrt or other rescue system then reset the mtdparts back to the original.
Re: Bricked NSA320S during 2017.07 flash March 11, 2021 10:58AM |
Registered: 3 years ago Posts: 32 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06 -0700) ZyXEL NSA310S/320S 1/2-Bay Power Media Server SoC: Kirkwood 88F6702_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA3x0S> setenv mtdparts 'mtdparts=orion_nand:0x100000(uboot)' NSA3x0S> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: WDC WD10EAVS-00D7B0 Firm: 01.01A01 Ser#: WD-WCAU41984981 Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 30717952 00057363-01 83 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... 70 bytes read in 538 ms (0 Bytes/s) Partition Map for IDE device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 1953523120 ec2d0c47-01 83 importing envs ... running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 507 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 5524320 bytes read in 777 ms (6.8 MiB/s) loading uInitrd ... 9484105 bytes read in 734 ms (12.3 MiB/s) loading DTB /boot/dts/kirkwood-nsa320s.dtb ... 12586 bytes read in 1461 ms (7.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.8.3-kirkwood-tld-1 Created: 2021-02-24 12:58:54 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5524256 Bytes = 5.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.8.3-kirkwood-tld-1 Created: 2021-02-24 12:59:13 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9484041 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f200000, end 0fb0b709 ... OK Loading Device Tree to 0f1f9000, end 0f1ff129 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.8.3-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Aug 22 16:10:01 PDT 2020 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Zyxel NSA320S [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot) [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 232740K/262144K available (10240K kernel code, 1085K rwdata, 4108K rodata, 1024K init, 298K bss, 29404K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x46c/0x808 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Rude variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000011][ T0] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000060][ T0] Switching to timer-based delay loop, resolution 6ns [ 0.000997][ T0] Console: colour dummy device 80x30 [ 0.001061][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.001094][ T0] pid_max: default: 32768 minimum: 301 [ 0.001592][ T0] LSM: Security Framework initializing [ 0.001768][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001803][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003347][ T0] CPU: Testing write buffer coherency: ok [ 0.005419][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.005787][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.006138][ T1] rcu: Hierarchical SRCU implementation. [ 0.009426][ T1] devtmpfs: initialized [ 0.017219][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.017263][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.017610][ T1] xor: measuring software checksum speed [ 0.110142][ T1] arm4regs : 902.000 MB/sec [ 0.210099][ T1] 8regs : 541.600 MB/sec [ 0.310092][ T1] 32regs : 787.200 MB/sec [ 0.310115][ T1] xor: using function: arm4regs (902.000 MB/sec) [ 0.310145][ T1] prandom: seed boundary self test passed [ 0.315186][ T1] prandom: 100 self tests passed [ 0.315202][ T1] pinctrl core: initialized pinctrl subsystem [ 0.316275][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.317072][ T1] NET: Registered protocol family 16 [ 0.317851][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.318940][ T1] audit: initializing netlink subsys (disabled) [ 0.320767][ T16] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 [ 0.320917][ T1] cpuidle: using governor ladder [ 0.321013][ T1] cpuidle: using governor menu [ 0.321603][ T1] Feroceon L2: Enabling L2 [ 0.321657][ T1] Feroceon L2: Cache support initialised. [ 0.334752][ T1] No ATAGs? [ 2.560067][ C0] random: fast init done [ 6.420382][ T1] raid6: int32x8 gen() 93 MB/s [ 6.590280][ T1] raid6: int32x8 xor() 58 MB/s [ 6.760228][ T1] raid6: int32x4 gen() 95 MB/s [ 6.930261][ T1] raid6: int32x4 xor() 61 MB/s [ 7.100089][ T1] raid6: int32x2 gen() 122 MB/s [ 7.270102][ T1] raid6: int32x2 xor() 74 MB/s [ 7.440200][ T1] raid6: int32x1 gen() 93 MB/s [ 7.610190][ T1] raid6: int32x1 xor() 54 MB/s [ 7.610204][ T1] raid6: using algorithm int32x2 gen() 122 MB/s [ 7.610214][ T1] raid6: .... xor() 74 MB/s, rmw enabled [ 7.610224][ T1] raid6: using intx1 recovery algorithm [ 7.610529][ T1] vgaarb: loaded [ 7.611192][ T1] SCSI subsystem initialized [ 7.611770][ T1] usbcore: registered new interface driver usbfs [ 7.611849][ T1] usbcore: registered new interface driver hub [ 7.611946][ T1] usbcore: registered new device driver usb [ 7.612175][ T1] pps_core: LinuxPPS API ver. 1 registered [ 7.612189][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 7.612220][ T1] PTP clock support registered [ 7.614022][ T1] clocksource: Switched to clocksource orion_clocksource [ 9.396250][ T1] VFS: Disk quotas dquot_6.6.0 [ 9.396368][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 9.408347][ T1] NET: Registered protocol family 2 [ 9.409371][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 9.409418][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 9.409462][ T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 9.409500][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 9.410013][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 9.410055][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 9.410316][ T1] NET: Registered protocol family 1 [ 9.411090][ T1] RPC: Registered named UNIX socket transport module. [ 9.411105][ T1] RPC: Registered udp transport module. [ 9.411116][ T1] RPC: Registered tcp transport module. [ 9.411127][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 9.411143][ T1] PCI: CLS 0 bytes, default 32 [ 9.411521][ T1] Trying to unpack rootfs image as initramfs... [ 10.393682][ T1] Freeing initrd memory: 9264K [ 10.393889][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 10.405963][ T1] Initialise system trusted keyrings [ 10.406030][ T1] Key type blacklist registered [ 10.406284][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 10.406408][ T1] zbud: loaded [ 10.408077][ T1] NFS: Registering the id_resolver key type [ 10.408115][ T1] Key type id_resolver registered [ 10.408127][ T1] Key type id_legacy registered [ 10.408153][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 10.408175][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 10.408500][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 10.409016][ T1] fuse: init (API version 7.31) [ 10.409478][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 10.409728][ T1] orangefs_init: module version upstream loaded [ 10.409743][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 10.529827][ T1] async_tx: api initialized (async) [ 10.529854][ T1] Key type asymmetric registered [ 10.529867][ T1] Asymmetric key parser 'x509' registered [ 10.529932][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 10.530155][ T1] io scheduler bfq registered [ 10.769496][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 10.771914][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 10.771942][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 10.771962][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 10.771980][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 10.772126][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 10.772174][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 10.773852][ T1] PCI: bus0: Fast back to back transfers disabled [ 10.773886][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 10.775483][ T1] PCI: bus1: Fast back to back transfers enabled [ 10.775514][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 10.775763][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref] [ 10.775785][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 10.776494][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 10.835251][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 10.838431][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 10.895215][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 10.898662][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 10.900244][ T1] printk: console [ttyS0] disabled [ 10.900351][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 10416666) is a 16550A [ 11.780561][ T1] printk: console [ttyS0] enabled [ 11.794944][ T1] loop: module loaded [ 11.799462][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 11.809021][ T1] scsi host0: sata_mv [ 11.813524][ T1] scsi host1: sata_mv [ 11.817722][ T1] ata1: SATA max UDMA/133 irq 32 [ 11.822495][ T1] ata2: SATA max UDMA/133 irq 32 [ 11.828457][ T1] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1 [ 11.835611][ T1] nand: Eon NAND 128MiB 3,3V 8-bit [ 11.840561][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 11.848861][ T1] Scanning device for bad blocks [ 11.858770][ T1] Bad eraseblock 100 at 0x000000c80000 [ 11.869180][ T1] Bad eraseblock 200 at 0x000001900000 [ 11.916293][ T1] 1 cmdlinepart partitions found on MTD device orion_nand [ 11.923226][ T1] Creating 1 MTD partitions on "orion_nand": [ 11.929072][ T1] 0x000000000000-0x000000100000 : "uboot" [ 11.936755][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 11.945300][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 11.957231][ T1] libphy: Fixed MDIO Bus: probed [ 11.963404][ T1] libphy: orion_mdio_bus: probed [ 11.968260][ T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@1: Whitelisted compatible string. Please remove [ 11.998504][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 12.007769][ T1] mv643xx_eth: Set the PHY to fix link down [ 12.008542][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 4c:9e:ff:0b:73:72 [ 12.023912][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.031260][ T1] ehci-pci: EHCI PCI platform driver [ 12.036526][ T1] ehci-orion: EHCI orion driver [ 12.041441][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 12.047709][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 12.056309][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 12.084171][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 12.091225][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08 [ 12.100210][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.108146][ T1] usb usb1: Product: EHCI Host Controller [ 12.113728][ T1] usb usb1: Manufacturer: Linux 5.8.3-kirkwood-tld-1 ehci_hcd [ 12.121051][ T1] usb usb1: SerialNumber: f1050000.ehci [ 12.127247][ T1] hub 1-0:1.0: USB hub found [ 12.131761][ T1] hub 1-0:1.0: 1 port detected [ 12.137328][ T1] usbcore: registered new interface driver usb-storage [ 12.144512][ T1] mousedev: PS/2 mouse device common for all mice [ 12.151129][ T1] i2c /dev entries driver [ 12.158084][ T1] ht1382 0-0068: registered as rtc0 [ 12.164235][ T1] ht1382 0-0068: setting system clock to 2021-03-11T08:43:28 UTC (1615452208) [ 12.174012][ T1] device-mapper: uevent: version 1.0.3 [ 12.179775][ T1] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com [ 12.189439][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 12.196711][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 12.203993][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 12.211407][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 12.218202][ T1] device-mapper: raid: Loading target version 1.15.1 [ 12.227305][ T1] hid: raw HID events driver (C) Jiri Kosina [ 12.233585][ T1] drop_monitor: Initializing network drop monitor service [ 12.241095][ T1] NET: Registered protocol family 10 [ 12.247852][ T1] Segment Routing with IPv6 [ 12.252193][ T1] RPL Segment Routing with IPv6 [ 12.257048][ T1] NET: Registered protocol family 17 [ 12.262419][ T1] Key type dns_resolver registered [ 12.267948][ T1] registered taskstats version 1 [ 12.272724][ T1] Loading compiled-in X.509 certificates [ 12.278375][ T1] zswap: loaded using pool lzo/zbud [ 12.283822][ T1] Key type ._fscrypt registered [ 12.288601][ T1] Key type .fscrypt registered [ 12.293199][ T1] Key type fscrypt-provisioning registered [ 12.300952][ T1] Key type big_key registered [ 12.340414][ T1] Key type encrypted registered [ 12.474080][ T89] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 12.504063][ T100] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 12.705943][ T100] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.32 [ 12.714821][ T100] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 12.722642][ T100] usb 1-1: Product: USB2.0 Hub [ 12.728275][ T100] hub 1-1:1.0: USB hub found [ 12.733194][ T100] hub 1-1:1.0: 4 ports detected [ 12.816256][ T89] ata1.00: ATA-8: WDC WD10EAVS-00D7B0, 01.01A01, max UDMA/133 [ 12.823545][ T89] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 12.835770][ T89] ata1.00: configured for UDMA/133 [ 12.851302][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD10EAVS-00D 1A01 PQ: 0 ANSI: 5 [ 12.861469][ T93] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 12.870428][ T93] sd 0:0:0:0: [sda] Write Protect is off [ 12.876315][ T93] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 12.897486][ T93] sda: sda1 [ 12.902259][ T93] sd 0:0:0:0: [sda] Attached SCSI disk [ 13.205738][ T91] ata2: SATA link down (SStatus 0 SControl F300) [ 13.225046][ T1] Freeing unused kernel memory: 1024K [ 13.231265][ T1] Checked W+X mappings: passed, no W+X pages found [ 13.237645][ T1] Run /init as init process Loading, please wait... Starting version 241 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. [ 47.328822][ C0] random: crng init done Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. done. Gave up waiting for root file system device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Missing modules (cat /proc/modules; ls /dev) ALERT! LABEL=rootfs does not exist. Dropping to a shell! BusyBox v1.30.1 (Debian 1:1.30.1-4) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs)
Re: Bricked NSA320S during 2017.07 flash March 11, 2021 05:18PM |
Admin Registered: 13 years ago Posts: 19,106 |
Begin: Running /scripts/local-block ... done.
e2fsck /dev/sdb1and check the label to make sure that it is rootfs
e2label /dev/sdb1
Re: Bricked NSA320S during 2017.07 flash April 09, 2021 02:22PM |
Registered: 3 years ago Posts: 32 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06 -0700) ZyXEL NSA310S/320S 1/2-Bay Power Media Server SoC: Kirkwood 88F6702_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA3x0S> setenv devices "usb" NSA3x0S> NSA3x0S> setenv bootcmd 'run init_sata_power; run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec;' NSA3x0S> NSA3x0S> printenv arcNumber=4931 baudrate=115200 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 bootcmd=run init_sata_power; run bootcmd_uenv; run scan_disk; run set_bootargs; bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then boose if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $l bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=ttyS0,115200 device=0:1 devices=usb disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-nsa320s.dtb ethact=egiga0 ethaddr=4c:9e:ff:0b:73:72 if_netconsole=ping $serverip init_ide=ide reset init_mmc=mmc rescan init_sata_power=mw.l f1010104 c70e0ffd init_usb=usb start ipaddr=192.168.100.11 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $d load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /b load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /bo load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x8000 partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; ; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $dis scan_ide=ide reset scan_mmc=mmc rescan scan_usb=usb start serverip=192.168.100.127 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 start_netconsole=setenv ncip; setenv bootdelay 10; setenv stdin nc; setenv stdou stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; se uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; uenv_loaded=0 uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknu uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_re usb_ready_retry=15 Environment size: 3247/131068 bytes NSA3x0S> setenv mtdparts "orion_nand:0x100000(uboot),0x80000(uboot_env)" NSA3x0S> printenv arcNumber=4931 baudrate=115200 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 bootcmd=run init_sata_power; run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=ttyS0,115200 device=0:1 devices=usb disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-nsa320s.dtb ethact=egiga0 ethaddr=4c:9e:ff:0b:73:72 if_netconsole=ping $serverip init_ide=ide reset init_mmc=mmc rescan init_sata_power=mw.l f1010104 c70e0ffd init_usb=usb start ipaddr=192.168.100.11 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done scan_ide=ide reset scan_mmc=mmc rescan scan_usb=usb start serverip=192.168.100.127 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_loaded=0 uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 3124/131068 bytes NSA3x0S> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 30717952 00057363-01 83 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... 70 bytes read in 538 ms (0 Bytes/s) importing envs ... running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 508 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 5524320 bytes read in 778 ms (6.8 MiB/s) loading uInitrd ... 9484105 bytes read in 736 ms (12.3 MiB/s) loading DTB /boot/dts/kirkwood-nsa320s.dtb ... 12586 bytes read in 1461 ms (7.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.8.3-kirkwood-tld-1 Created: 2021-02-24 12:58:54 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5524256 Bytes = 5.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.8.3-kirkwood-tld-1 Created: 2021-02-24 12:59:13 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9484041 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f200000, end 0fb0b709 ... OK Loading Device Tree to 0f1f9000, end 0f1ff129 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.8.3-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Aug 22 16:10:01 PDT 2020 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Zyxel NSA320S [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 orion_nand:0x100000(uboot),0x80000(uboot_env) [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 232740K/262144K available (10240K kernel code, 1085K rwdata, 4108K rodata, 1024K init, 298K bss, 29404K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x46c/0x808 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Rude variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000011][ T0] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000060][ T0] Switching to timer-based delay loop, resolution 6ns [ 0.000994][ T0] Console: colour dummy device 80x30 [ 0.001058][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.001089][ T0] pid_max: default: 32768 minimum: 301 [ 0.001590][ T0] LSM: Security Framework initializing [ 0.001764][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001798][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003330][ T0] CPU: Testing write buffer coherency: ok [ 0.005399][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.005766][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.006115][ T1] rcu: Hierarchical SRCU implementation. [ 0.009409][ T1] devtmpfs: initialized [ 0.017294][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.017337][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.017686][ T1] xor: measuring software checksum speed [ 0.110144][ T1] arm4regs : 902.000 MB/sec [ 0.210100][ T1] 8regs : 541.600 MB/sec [ 0.310098][ T1] 32regs : 787.600 MB/sec [ 0.310122][ T1] xor: using function: arm4regs (902.000 MB/sec) [ 0.310152][ T1] prandom: seed boundary self test passed [ 0.315191][ T1] prandom: 100 self tests passed [ 0.315207][ T1] pinctrl core: initialized pinctrl subsystem [ 0.316264][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.317066][ T1] NET: Registered protocol family 16 [ 0.317898][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.318977][ T1] audit: initializing netlink subsys (disabled) [ 0.320802][ T16] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 [ 0.320951][ T1] cpuidle: using governor ladder [ 0.321048][ T1] cpuidle: using governor menu [ 0.321694][ T1] Feroceon L2: Enabling L2 [ 0.321748][ T1] Feroceon L2: Cache support initialised. [ 0.334839][ T1] No ATAGs? [ 2.560067][ C0] random: fast init done [ 6.420184][ T1] raid6: int32x8 gen() 93 MB/s [ 6.590220][ T1] raid6: int32x8 xor() 58 MB/s [ 6.760263][ T1] raid6: int32x4 gen() 95 MB/s [ 6.930227][ T1] raid6: int32x4 xor() 61 MB/s [ 7.100119][ T1] raid6: int32x2 gen() 121 MB/s [ 7.270147][ T1] raid6: int32x2 xor() 75 MB/s [ 7.440256][ T1] raid6: int32x1 gen() 93 MB/s [ 7.610117][ T1] raid6: int32x1 xor() 54 MB/s [ 7.610131][ T1] raid6: using algorithm int32x2 gen() 121 MB/s [ 7.610141][ T1] raid6: .... xor() 75 MB/s, rmw enabled [ 7.610152][ T1] raid6: using intx1 recovery algorithm [ 7.610462][ T1] vgaarb: loaded [ 7.611124][ T1] SCSI subsystem initialized [ 7.611695][ T1] usbcore: registered new interface driver usbfs [ 7.611773][ T1] usbcore: registered new interface driver hub [ 7.611872][ T1] usbcore: registered new device driver usb [ 7.612098][ T1] pps_core: LinuxPPS API ver. 1 registered [ 7.612112][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 7.612144][ T1] PTP clock support registered [ 7.614004][ T1] clocksource: Switched to clocksource orion_clocksource [ 9.396748][ T1] VFS: Disk quotas dquot_6.6.0 [ 9.396866][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 9.408802][ T1] NET: Registered protocol family 2 [ 9.409827][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 9.409874][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 9.409918][ T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 9.409956][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 9.410468][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 9.410511][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 9.410774][ T1] NET: Registered protocol family 1 [ 9.411538][ T1] RPC: Registered named UNIX socket transport module. [ 9.411553][ T1] RPC: Registered udp transport module. [ 9.411564][ T1] RPC: Registered tcp transport module. [ 9.411575][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 9.411592][ T1] PCI: CLS 0 bytes, default 32 [ 9.411969][ T1] Trying to unpack rootfs image as initramfs... [ 10.393900][ T1] Freeing initrd memory: 9264K [ 10.394262][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 10.406253][ T1] Initialise system trusted keyrings [ 10.406320][ T1] Key type blacklist registered [ 10.406572][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 10.406697][ T1] zbud: loaded [ 10.408362][ T1] NFS: Registering the id_resolver key type [ 10.408397][ T1] Key type id_resolver registered [ 10.408409][ T1] Key type id_legacy registered [ 10.408435][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 10.408456][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 10.408780][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 10.409294][ T1] fuse: init (API version 7.31) [ 10.409752][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 10.410003][ T1] orangefs_init: module version upstream loaded [ 10.410019][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 10.528818][ T1] async_tx: api initialized (async) [ 10.528845][ T1] Key type asymmetric registered [ 10.528857][ T1] Asymmetric key parser 'x509' registered [ 10.528922][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 10.529146][ T1] io scheduler bfq registered [ 10.768449][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 10.770867][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 10.770895][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 10.770915][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 10.770933][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 10.771079][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 10.771127][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 10.772805][ T1] PCI: bus0: Fast back to back transfers disabled [ 10.772838][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 10.774431][ T1] PCI: bus1: Fast back to back transfers enabled [ 10.774462][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 10.774713][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref] [ 10.774735][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 10.775447][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 10.835233][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 10.838414][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 10.895199][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 10.898625][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 10.900216][ T1] printk: console [ttyS0] disabled [ 10.900321][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 10416666) is a 16550A [ 11.781392][ T1] printk: console [ttyS0] enabled [ 11.795802][ T1] loop: module loaded [ 11.800317][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 11.809869][ T1] scsi host0: sata_mv [ 11.814444][ T1] scsi host1: sata_mv [ 11.818570][ T1] ata1: SATA max UDMA/133 irq 32 [ 11.823344][ T1] ata2: SATA max UDMA/133 irq 32 [ 11.829337][ T1] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1 [ 11.836495][ T1] nand: Eon NAND 128MiB 3,3V 8-bit [ 11.841445][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 11.849751][ T1] Scanning device for bad blocks [ 11.859675][ T1] Bad eraseblock 100 at 0x000000c80000 [ 11.870091][ T1] Bad eraseblock 200 at 0x000001900000 [ 11.917247][ T1] 9 fixed-partitions partitions found on MTD device orion_nand [ 11.924636][ T1] Creating 9 MTD partitions on "orion_nand": [ 11.930458][ T1] 0x000000000000-0x000000100000 : "uboot" [ 11.937776][ T1] 0x000000100000-0x000000180000 : "uboot_env" [ 11.945358][ T1] 0x000000180000-0x000000200000 : "key_store" [ 11.952859][ T1] 0x000000200000-0x000000280000 : "info" [ 11.960000][ T1] 0x000000280000-0x000000c80000 : "etc" [ 11.967115][ T1] 0x000000c80000-0x000001680000 : "kernel_1" [ 11.974622][ T1] 0x000001680000-0x000004640000 : "rootfs1" [ 11.982208][ T1] 0x000004640000-0x000005040000 : "kernel_2" [ 11.989735][ T1] 0x000005040000-0x000008000000 : "rootfs2" [ 11.997853][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 12.006397][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 12.018341][ T1] libphy: Fixed MDIO Bus: probed [ 12.024563][ T1] libphy: orion_mdio_bus: probed [ 12.029368][ T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@1: Whitelisted compatible string. Please remove [ 12.059766][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 12.069030][ T1] mv643xx_eth: Set the PHY to fix link down [ 12.069809][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 4c:9e:ff:0b:73:72 [ 12.085352][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.092619][ T1] ehci-pci: EHCI PCI platform driver [ 12.097948][ T1] ehci-orion: EHCI orion driver [ 12.102909][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 12.109203][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 12.117794][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 12.154033][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 12.161104][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08 [ 12.170145][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.178059][ T1] usb usb1: Product: EHCI Host Controller [ 12.183615][ T1] usb usb1: Manufacturer: Linux 5.8.3-kirkwood-tld-1 ehci_hcd [ 12.190921][ T1] usb usb1: SerialNumber: f1050000.ehci [ 12.197092][ T1] hub 1-0:1.0: USB hub found [ 12.201568][ T1] hub 1-0:1.0: 1 port detected [ 12.207075][ T1] usbcore: registered new interface driver usb-storage [ 12.214256][ T1] mousedev: PS/2 mouse device common for all mice [ 12.220819][ T1] i2c /dev entries driver [ 12.227746][ T1] ht1382 0-0068: registered as rtc0 [ 12.233862][ T1] ht1382 0-0068: setting system clock to 2021-04-09T17:18:50 UTC (1617988730) [ 12.243615][ T1] device-mapper: uevent: version 1.0.3 [ 12.249326][ T1] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com [ 12.258995][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 12.266273][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 12.273554][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 12.280967][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 12.287756][ T1] device-mapper: raid: Loading target version 1.15.1 [ 12.296891][ T1] hid: raw HID events driver (C) Jiri Kosina [ 12.303137][ T1] drop_monitor: Initializing network drop monitor service [ 12.310658][ T1] NET: Registered protocol family 10 [ 12.317410][ T1] Segment Routing with IPv6 [ 12.321755][ T1] RPL Segment Routing with IPv6 [ 12.326613][ T1] NET: Registered protocol family 17 [ 12.331998][ T1] Key type dns_resolver registered [ 12.337591][ T1] registered taskstats version 1 [ 12.342364][ T1] Loading compiled-in X.509 certificates [ 12.348014][ T1] zswap: loaded using pool lzo/zbud [ 12.353458][ T1] Key type ._fscrypt registered [ 12.358239][ T1] Key type .fscrypt registered [ 12.362839][ T1] Key type fscrypt-provisioning registered [ 12.370611][ T1] Key type big_key registered [ 12.404143][ T89] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 12.417898][ T1] Key type encrypted registered [ 12.574040][ T100] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 12.775931][ T100] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.32 [ 12.784933][ T100] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 12.792769][ T100] usb 1-1: Product: USB2.0 Hub [ 12.798381][ T100] hub 1-1:1.0: USB hub found [ 12.803180][ T100] hub 1-1:1.0: 4 ports detected [ 14.014115][ T89] ata1.00: ATA-8: WDC WD10EAVS-00D7B0, 01.01A01, max UDMA/133 [ 14.021405][ T89] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 14.033611][ T89] ata1.00: configured for UDMA/133 [ 14.049171][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD10EAVS-00D 1A01 PQ: 0 ANSI: 5 [ 14.059323][ T93] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 14.068291][ T93] sd 0:0:0:0: [sda] Write Protect is off [ 14.073947][ T93] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 14.094459][ T93] sda: sda1 [ 14.099212][ T93] sd 0:0:0:0: [sda] Attached SCSI disk [ 14.704051][ T91] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 14.744095][ T91] ata2.00: ATA-8: WDC WD10EAVS-00D7B0, 01.01A01, max UDMA/133 [ 14.751380][ T91] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 14.763570][ T91] ata2.00: configured for UDMA/133 [ 14.779082][ T58] scsi 1:0:0:0: Direct-Access ATA WDC WD10EAVS-00D 1A01 PQ: 0 ANSI: 5 [ 14.789226][ T93] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 14.798022][ T93] sd 1:0:0:0: [sdb] Write Protect is off [ 14.803636][ T93] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 14.821677][ T93] sdb: sdb1 sdb2 [ 14.827089][ T93] sd 1:0:0:0: [sdb] Attached SCSI disk [ 14.835542][ T1] Freeing unused kernel memory: 1024K [ 14.855080][ T1] Checked W+X mappings: passed, no W+X pages found [ 14.861430][ T1] Run /init as init process Loading, please wait... Starting version 241 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 27.925639][ T149] __nand_correct_data: uncorrectable ECC error [ 27.931636][ T149] __nand_correct_data: uncorrectable ECC error [ 27.937699][ T149] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 27.949313][ T149] __nand_correct_data: uncorrectable ECC error [ 27.955321][ T149] __nand_correct_data: uncorrectable ECC error [ 27.961314][ T149] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 27.972335][ T149] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 30.103521][ T149] __nand_correct_data: uncorrectable ECC error [ 30.109622][ T149] __nand_correct_data: uncorrectable ECC error [ 30.115673][ T149] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 30.127292][ T149] __nand_correct_data: uncorrectable ECC error [ 30.133271][ T149] __nand_correct_data: uncorrectable ECC error [ 30.139290][ T149] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 30.150314][ T149] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done. [ 31.674673][ T153] __nand_correct_data: uncorrectable ECC error [ 31.680670][ T153] __nand_correct_data: uncorrectable ECC error [ 31.686729][ T153] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 31.698343][ T153] __nand_correct_data: uncorrectable ECC error [ 31.704356][ T153] __nand_correct_data: uncorrectable ECC error [ 31.710348][ T153] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 31.721370][ T153] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 32.219759][ T153] __nand_correct_data: uncorrectable ECC error [ 32.225859][ T153] __nand_correct_data: uncorrectable ECC error [ 32.231853][ T153] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 32.243454][ T153] __nand_correct_data: uncorrectable ECC error [ 32.249527][ T153] __nand_correct_data: uncorrectable ECC error [ 32.255542][ T153] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 32.266562][ T153] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 34.286406][ T157] __nand_correct_data: uncorrectable ECC error [ 34.292395][ T157] __nand_correct_data: uncorrectable ECC error [ 34.298461][ T157] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 34.310076][ T157] __nand_correct_data: uncorrectable ECC error [ 34.316088][ T157] __nand_correct_data: uncorrectable ECC error [ 34.322082][ T157] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 34.333102][ T157] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 34.831156][ T157] __nand_correct_data: uncorrectable ECC error [ 34.837259][ T157] __nand_correct_data: uncorrectable ECC error [ 34.843258][ T157] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 34.854859][ T157] __nand_correct_data: uncorrectable ECC error [ 34.860845][ T157] __nand_correct_data: uncorrectable ECC error [ 34.866922][ T157] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 34.877953][ T157] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 36.897152][ T161] __nand_correct_data: uncorrectable ECC error [ 36.903144][ T161] __nand_correct_data: uncorrectable ECC error [ 36.909220][ T161] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 36.920854][ T161] __nand_correct_data: uncorrectable ECC error [ 36.926864][ T161] __nand_correct_data: uncorrectable ECC error [ 36.932856][ T161] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 36.943878][ T161] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 37.441488][ T161] __nand_correct_data: uncorrectable ECC error [ 37.447589][ T161] __nand_correct_data: uncorrectable ECC error [ 37.453583][ T161] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 37.465184][ T161] __nand_correct_data: uncorrectable ECC error [ 37.471162][ T161] __nand_correct_data: uncorrectable ECC error [ 37.477239][ T161] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 37.488269][ T161] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 37.833832][ C0] random: crng init done Begin: Running /scripts/local-block ... done. [ 39.508473][ T165] __nand_correct_data: uncorrectable ECC error [ 39.514570][ T165] __nand_correct_data: uncorrectable ECC error [ 39.520566][ T165] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 39.532163][ T165] __nand_correct_data: uncorrectable ECC error [ 39.538231][ T165] __nand_correct_data: uncorrectable ECC error [ 39.544246][ T165] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 39.555265][ T165] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 40.053326][ T165] __nand_correct_data: uncorrectable ECC error [ 40.059430][ T165] __nand_correct_data: uncorrectable ECC error [ 40.065481][ T165] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 40.077099][ T165] __nand_correct_data: uncorrectable ECC error [ 40.083086][ T165] __nand_correct_data: uncorrectable ECC error [ 40.089107][ T165] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 40.100131][ T165] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 42.120063][ T169] __nand_correct_data: uncorrectable ECC error [ 42.126169][ T169] __nand_correct_data: uncorrectable ECC error [ 42.132161][ T169] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 42.143761][ T169] __nand_correct_data: uncorrectable ECC error [ 42.149828][ T169] __nand_correct_data: uncorrectable ECC error [ 42.155849][ T169] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 42.166869][ T169] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 42.665121][ T169] __nand_correct_data: uncorrectable ECC error [ 42.671114][ T169] __nand_correct_data: uncorrectable ECC error [ 42.677176][ T169] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 42.688786][ T169] __nand_correct_data: uncorrectable ECC error [ 42.694798][ T169] __nand_correct_data: uncorrectable ECC error [ 42.700791][ T169] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 42.711812][ T169] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 44.730822][ T173] __nand_correct_data: uncorrectable ECC error [ 44.736929][ T173] __nand_correct_data: uncorrectable ECC error [ 44.742928][ T173] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 44.754529][ T173] __nand_correct_data: uncorrectable ECC error [ 44.760515][ T173] __nand_correct_data: uncorrectable ECC error [ 44.766590][ T173] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 44.777621][ T173] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 45.275812][ T173] __nand_correct_data: uncorrectable ECC error [ 45.281801][ T173] __nand_correct_data: uncorrectable ECC error [ 45.287866][ T173] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 45.299474][ T173] __nand_correct_data: uncorrectable ECC error [ 45.305485][ T173] __nand_correct_data: uncorrectable ECC error [ 45.311478][ T173] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 45.322500][ T173] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 47.341436][ T177] __nand_correct_data: uncorrectable ECC error [ 47.347538][ T177] __nand_correct_data: uncorrectable ECC error [ 47.353529][ T177] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 47.365128][ T177] __nand_correct_data: uncorrectable ECC error [ 47.371108][ T177] __nand_correct_data: uncorrectable ECC error [ 47.377184][ T177] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 47.388214][ T177] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 47.886156][ T177] __nand_correct_data: uncorrectable ECC error [ 47.892145][ T177] __nand_correct_data: uncorrectable ECC error [ 47.898208][ T177] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 47.909819][ T177] __nand_correct_data: uncorrectable ECC error [ 47.915829][ T177] __nand_correct_data: uncorrectable ECC error [ 47.921822][ T177] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 47.932843][ T177] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 49.952892][ T181] __nand_correct_data: uncorrectable ECC error [ 49.958997][ T181] __nand_correct_data: uncorrectable ECC error [ 49.965056][ T181] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 49.976674][ T181] __nand_correct_data: uncorrectable ECC error [ 49.982659][ T181] __nand_correct_data: uncorrectable ECC error [ 49.988680][ T181] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 49.999704][ T181] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 50.497843][ T181] __nand_correct_data: uncorrectable ECC error [ 50.503834][ T181] __nand_correct_data: uncorrectable ECC error [ 50.509924][ T181] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 50.521516][ T181] __nand_correct_data: uncorrectable ECC error [ 50.527584][ T181] __nand_correct_data: uncorrectable ECC error [ 50.533574][ T181] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 50.544598][ T181] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 52.563905][ T185] __nand_correct_data: uncorrectable ECC error [ 52.570011][ T185] __nand_correct_data: uncorrectable ECC error [ 52.576061][ T185] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 52.587682][ T185] __nand_correct_data: uncorrectable ECC error [ 52.593668][ T185] __nand_correct_data: uncorrectable ECC error [ 52.599688][ T185] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 52.610711][ T185] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 53.108970][ T185] __nand_correct_data: uncorrectable ECC error [ 53.115074][ T185] __nand_correct_data: uncorrectable ECC error [ 53.121065][ T185] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 53.132786][ T185] __nand_correct_data: uncorrectable ECC error [ 53.138871][ T185] __nand_correct_data: uncorrectable ECC error [ 53.144895][ T185] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 53.155922][ T185] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 55.186452][ T189] __nand_correct_data: uncorrectable ECC error [ 55.192443][ T189] __nand_correct_data: uncorrectable ECC error [ 55.198507][ T189] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 55.210119][ T189] __nand_correct_data: uncorrectable ECC error [ 55.216139][ T189] __nand_correct_data: uncorrectable ECC error [ 55.222129][ T189] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 55.233150][ T189] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 55.731035][ T189] __nand_correct_data: uncorrectable ECC error [ 55.737140][ T189] __nand_correct_data: uncorrectable ECC error [ 55.743134][ T189] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 55.754731][ T189] __nand_correct_data: uncorrectable ECC error [ 55.760712][ T189] __nand_correct_data: uncorrectable ECC error [ 55.766786][ T189] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 55.777810][ T189] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 57.808388][ T193] __nand_correct_data: uncorrectable ECC error [ 57.814487][ T193] __nand_correct_data: uncorrectable ECC error [ 57.820482][ T193] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 57.832080][ T193] __nand_correct_data: uncorrectable ECC error [ 57.838148][ T193] __nand_correct_data: uncorrectable ECC error [ 57.844163][ T193] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 57.855183][ T193] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 58.353090][ T193] __nand_correct_data: uncorrectable ECC error [ 58.359191][ T193] __nand_correct_data: uncorrectable ECC error [ 58.365243][ T193] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 58.376862][ T193] __nand_correct_data: uncorrectable ECC error [ 58.382847][ T193] __nand_correct_data: uncorrectable ECC error [ 58.388867][ T193] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 58.399891][ T193] Buffer I/O error on dev mtdblock5, logical block 0, async page read Begin: Running /scripts/local-block ... done. [ 60.430293][ T197] __nand_correct_data: uncorrectable ECC error [ 60.436398][ T197] __nand_correct_data: uncorrectable ECC error [ 60.442395][ T197] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 60.453993][ T197] __nand_correct_data: uncorrectable ECC error [ 60.460061][ T197] __nand_correct_data: uncorrectable ECC error [ 60.466076][ T197] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 60.477104][ T197] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 60.974959][ T197] __nand_correct_data: uncorrectable ECC error [ 60.980949][ T197] __nand_correct_data: uncorrectable ECC error [ 60.987012][ T197] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 60.998623][ T197] __nand_correct_data: uncorrectable ECC error [ 61.004634][ T197] __nand_correct_data: uncorrectable ECC error [ 61.010626][ T197] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 61.021648][ T197] Buffer I/O error on dev mtdblock5, logical block 0, async page read done. [ 62.049726][ T199] __nand_correct_data: uncorrectable ECC error [ 62.055834][ T199] __nand_correct_data: uncorrectable ECC error [ 62.061824][ T199] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 62.073422][ T199] __nand_correct_data: uncorrectable ECC error [ 62.079488][ T199] __nand_correct_data: uncorrectable ECC error [ 62.085620][ T199] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 62.096654][ T199] Buffer I/O error on dev mtdblock5, logical block 0, async page read [ 62.594408][ T199] __nand_correct_data: uncorrectable ECC error [ 62.600405][ T199] __nand_correct_data: uncorrectable ECC error [ 62.606466][ T199] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 62.618078][ T199] __nand_correct_data: uncorrectable ECC error [ 62.624090][ T199] __nand_correct_data: uncorrectable ECC error [ 62.630082][ T199] blk_update_request: I/O error, dev mtdblock5, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 62.641104][ T199] Buffer I/O error on dev mtdblock5, logical block 0, async page read Gave up waiting for root file system device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Missing modules (cat /proc/modules; ls /dev) ALERT! LABEL=rootfs does not exist. Dropping to a shell! BusyBox v1.30.1 (Debian 1:1.30.1-4) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs)
Re: Bricked NSA320S during 2017.07 flash April 09, 2021 04:26PM |
Admin Registered: 13 years ago Posts: 19,106 |
mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env)
setenv mtdparts 'mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env)' printenvAnd then
boot
Re: Bricked NSA320S during 2017.07 flash April 10, 2021 04:58PM |
Registered: 3 years ago Posts: 32 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06 -0700) ZyXEL NSA310S/320S 1/2-Bay Power Media Server SoC: Kirkwood 88F6702_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA3x0S> setenv mtdparts 'mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env) ' NSA3x0S> printenv arcNumber=4931 baudrate=115200 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=ttyS0,115200 device=0:1 devices=usb disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-nsa320s.dtb ethact=egiga0 ethaddr=4c:9e:ff:0b:73:72 if_netconsole=ping $serverip init_ide=ide reset init_mmc=mmc rescan init_sata_power=mw.l f1010104 c70e0ffd init_usb=usb start ipaddr=192.168.100.11 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done scan_ide=ide reset scan_mmc=mmc rescan scan_usb=usb start serverip=192.168.100.127 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_loaded=0 uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 3112/131068 bytes NSA3x0S> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 30717952 00057363-01 83 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... 70 bytes read in 538 ms (0 Bytes/s) importing envs ... running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 508 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 5524320 bytes read in 778 ms (6.8 MiB/s) loading uInitrd ... 9484105 bytes read in 736 ms (12.3 MiB/s) loading DTB /boot/dts/kirkwood-nsa320s.dtb ... 12586 bytes read in 1461 ms (7.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.8.3-kirkwood-tld-1 Created: 2021-02-24 12:58:54 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5524256 Bytes = 5.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.8.3-kirkwood-tld-1 Created: 2021-02-24 12:59:13 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9484041 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f200000, end 0fb0b709 ... OK Loading Device Tree to 0f1f9000, end 0f1ff129 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.8.3-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Aug 22 16:10:01 PDT 2020 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Zyxel NSA320S [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env) [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 232740K/262144K available (10240K kernel code, 1085K rwdata, 4108K rodata, 1024K init, 298K bss, 29404K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x46c/0x808 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Rude variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000011][ T0] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000060][ T0] Switching to timer-based delay loop, resolution 6ns [ 0.000996][ T0] Console: colour dummy device 80x30 [ 0.001059][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.001093][ T0] pid_max: default: 32768 minimum: 301 [ 0.001587][ T0] LSM: Security Framework initializing [ 0.001764][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001797][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003331][ T0] CPU: Testing write buffer coherency: ok [ 0.005402][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.005769][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.006119][ T1] rcu: Hierarchical SRCU implementation. [ 0.009409][ T1] devtmpfs: initialized [ 0.017218][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.017261][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.017605][ T1] xor: measuring software checksum speed [ 0.110138][ T1] arm4regs : 901.600 MB/sec [ 0.210101][ T1] 8regs : 541.600 MB/sec [ 0.310096][ T1] 32regs : 787.200 MB/sec [ 0.310120][ T1] xor: using function: arm4regs (901.600 MB/sec) [ 0.310149][ T1] prandom: seed boundary self test passed [ 0.315189][ T1] prandom: 100 self tests passed [ 0.315204][ T1] pinctrl core: initialized pinctrl subsystem [ 0.316269][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.317069][ T1] NET: Registered protocol family 16 [ 0.317848][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.318933][ T1] audit: initializing netlink subsys (disabled) [ 0.320767][ T16] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 [ 0.320918][ T1] cpuidle: using governor ladder [ 0.321015][ T1] cpuidle: using governor menu [ 0.321605][ T1] Feroceon L2: Enabling L2 [ 0.321660][ T1] Feroceon L2: Cache support initialised. [ 0.334746][ T1] No ATAGs? [ 2.560067][ C0] random: fast init done [ 6.420148][ T1] raid6: int32x8 gen() 93 MB/s [ 6.590342][ T1] raid6: int32x8 xor() 58 MB/s [ 6.760181][ T1] raid6: int32x4 gen() 95 MB/s [ 6.930241][ T1] raid6: int32x4 xor() 61 MB/s [ 7.100151][ T1] raid6: int32x2 gen() 123 MB/s [ 7.270117][ T1] raid6: int32x2 xor() 75 MB/s [ 7.440182][ T1] raid6: int32x1 gen() 93 MB/s [ 7.610252][ T1] raid6: int32x1 xor() 54 MB/s [ 7.610265][ T1] raid6: using algorithm int32x2 gen() 123 MB/s [ 7.610276][ T1] raid6: .... xor() 75 MB/s, rmw enabled [ 7.610286][ T1] raid6: using intx1 recovery algorithm [ 7.610594][ T1] vgaarb: loaded [ 7.611260][ T1] SCSI subsystem initialized [ 7.611841][ T1] usbcore: registered new interface driver usbfs [ 7.611917][ T1] usbcore: registered new interface driver hub [ 7.612014][ T1] usbcore: registered new device driver usb [ 7.612242][ T1] pps_core: LinuxPPS API ver. 1 registered [ 7.612256][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 7.612288][ T1] PTP clock support registered [ 7.614105][ T1] clocksource: Switched to clocksource orion_clocksource [ 9.396920][ T1] VFS: Disk quotas dquot_6.6.0 [ 9.397038][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 9.409015][ T1] NET: Registered protocol family 2 [ 9.410035][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 9.410082][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 9.410126][ T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 9.410164][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 9.410681][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 9.410725][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 9.410987][ T1] NET: Registered protocol family 1 [ 9.411753][ T1] RPC: Registered named UNIX socket transport module. [ 9.411769][ T1] RPC: Registered udp transport module. [ 9.411779][ T1] RPC: Registered tcp transport module. [ 9.411789][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 9.411807][ T1] PCI: CLS 0 bytes, default 32 [ 9.412183][ T1] Trying to unpack rootfs image as initramfs... [ 10.394806][ T1] Freeing initrd memory: 9264K [ 10.395012][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 10.406993][ T1] Initialise system trusted keyrings [ 10.407063][ T1] Key type blacklist registered [ 10.407309][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 10.407432][ T1] zbud: loaded [ 10.409097][ T1] NFS: Registering the id_resolver key type [ 10.409137][ T1] Key type id_resolver registered [ 10.409150][ T1] Key type id_legacy registered [ 10.409175][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 10.409197][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 10.409521][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 10.410039][ T1] fuse: init (API version 7.31) [ 10.410501][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 10.410754][ T1] orangefs_init: module version upstream loaded [ 10.410769][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 10.532837][ T1] async_tx: api initialized (async) [ 10.532865][ T1] Key type asymmetric registered [ 10.532878][ T1] Asymmetric key parser 'x509' registered [ 10.532943][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 10.533166][ T1] io scheduler bfq registered [ 10.772441][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 10.774935][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 10.774963][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 10.774983][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 10.775000][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 10.775146][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 10.775195][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 10.776868][ T1] PCI: bus0: Fast back to back transfers disabled [ 10.776901][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 10.778421][ T1] PCI: bus1: Fast back to back transfers enabled [ 10.778452][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 10.778699][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref] [ 10.778721][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 10.779423][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 10.835341][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 10.838483][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 10.895293][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 10.898736][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 10.900321][ T1] printk: console [ttyS0] disabled [ 10.900427][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 10416666) is a 16550A [ 11.782329][ T1] printk: console [ttyS0] enabled [ 11.796730][ T1] loop: module loaded [ 11.801243][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 11.810798][ T1] scsi host0: sata_mv [ 11.815363][ T1] scsi host1: sata_mv [ 11.819484][ T1] ata1: SATA max UDMA/133 irq 32 [ 11.824357][ T1] ata2: SATA max UDMA/133 irq 32 [ 11.830266][ T1] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1 [ 11.837421][ T1] nand: Eon NAND 128MiB 3,3V 8-bit [ 11.842372][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 11.850670][ T1] Scanning device for bad blocks [ 11.860595][ T1] Bad eraseblock 100 at 0x000000c80000 [ 11.871011][ T1] Bad eraseblock 200 at 0x000001900000 [ 11.918101][ T1] 2 cmdlinepart partitions found on MTD device orion_nand [ 11.925060][ T1] Creating 2 MTD partitions on "orion_nand": [ 11.930884][ T1] 0x000000000000-0x000000100000 : "uboot" [ 11.938170][ T1] 0x000000100000-0x000000180000 : "uboot_env" [ 11.946129][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 11.954668][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 11.966555][ T1] libphy: Fixed MDIO Bus: probed [ 11.972759][ T1] libphy: orion_mdio_bus: probed [ 11.977614][ T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@1: Whitelisted compatible string. Please remove [ 12.007989][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 12.016937][ T1] mv643xx_eth: Set the PHY to fix link down [ 12.017921][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 4c:9e:ff:0b:73:72 [ 12.033304][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.040656][ T1] ehci-pci: EHCI PCI platform driver [ 12.045926][ T1] ehci-orion: EHCI orion driver [ 12.050837][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 12.057127][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 12.065720][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 12.094250][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 12.101284][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08 [ 12.110273][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.118208][ T1] usb usb1: Product: EHCI Host Controller [ 12.123790][ T1] usb usb1: Manufacturer: Linux 5.8.3-kirkwood-tld-1 ehci_hcd [ 12.131113][ T1] usb usb1: SerialNumber: f1050000.ehci [ 12.137320][ T1] hub 1-0:1.0: USB hub found [ 12.141841][ T1] hub 1-0:1.0: 1 port detected [ 12.147397][ T1] usbcore: registered new interface driver usb-storage [ 12.154635][ T1] mousedev: PS/2 mouse device common for all mice [ 12.161235][ T1] i2c /dev entries driver [ 12.168248][ T1] ht1382 0-0068: registered as rtc0 [ 12.174373][ T1] ht1382 0-0068: setting system clock to 2021-04-10T13:40:24 UTC (1618062024) [ 12.184065][ T1] device-mapper: uevent: version 1.0.3 [ 12.189814][ T1] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@redhat.com [ 12.199476][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 12.206753][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 12.214037][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 12.221450][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 12.228246][ T1] device-mapper: raid: Loading target version 1.15.1 [ 12.237398][ T1] hid: raw HID events driver (C) Jiri Kosina [ 12.243647][ T1] drop_monitor: Initializing network drop monitor service [ 12.251154][ T1] NET: Registered protocol family 10 [ 12.257915][ T1] Segment Routing with IPv6 [ 12.262264][ T1] RPL Segment Routing with IPv6 [ 12.267119][ T1] NET: Registered protocol family 17 [ 12.272502][ T1] Key type dns_resolver registered [ 12.278021][ T1] registered taskstats version 1 [ 12.282795][ T1] Loading compiled-in X.509 certificates [ 12.288441][ T1] zswap: loaded using pool lzo/zbud [ 12.293885][ T1] Key type ._fscrypt registered [ 12.298662][ T1] Key type .fscrypt registered [ 12.303261][ T1] Key type fscrypt-provisioning registered [ 12.311026][ T1] Key type big_key registered [ 12.350487][ T1] Key type encrypted registered [ 12.474160][ T89] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 12.514151][ T100] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 12.715979][ T100] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.32 [ 12.724859][ T100] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 12.732677][ T100] usb 1-1: Product: USB2.0 Hub [ 12.738301][ T100] hub 1-1:1.0: USB hub found [ 12.743228][ T100] hub 1-1:1.0: 4 ports detected [ 13.304213][ T89] ata1.00: ATA-8: WDC WD10EAVS-00D7B0, 01.01A01, max UDMA/133 [ 13.311503][ T89] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 13.323721][ T89] ata1.00: configured for UDMA/133 [ 13.339286][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD10EAVS-00D 1A01 PQ: 0 ANSI: 5 [ 13.349462][ T93] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 13.358433][ T93] sd 0:0:0:0: [sda] Write Protect is off [ 13.364091][ T93] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 13.384439][ T93] sda: sda1 [ 13.389201][ T93] sd 0:0:0:0: [sda] Attached SCSI disk [ 13.685814][ T91] ata2: SATA link down (SStatus 0 SControl F300) [ 13.705115][ T1] Freeing unused kernel memory: 1024K [ 13.711336][ T1] Checked W+X mappings: passed, no W+X pages found [ 13.717715][ T1] Run /init as init process Loading, please wait... Starting version 241 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. [ 48.549101][ C0] random: crng init done Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. Begin: Running /scripts/local-block ... done. done. Gave up waiting for root file system device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Missing modules (cat /proc/modules; ls /dev) ALERT! LABEL=rootfs does not exist. Dropping to a shell! BusyBox v1.30.1 (Debian 1:1.30.1-4) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs)
Re: Bricked NSA320S during 2017.07 flash April 10, 2021 05:42PM |
Admin Registered: 13 years ago Posts: 19,106 |
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env)The kernel will look for a partition that has the label rootfs. It will scan all drives, USB and HDD, to find that partition.
Re: Bricked NSA320S during 2017.07 flash April 11, 2021 03:18PM |
Registered: 3 years ago Posts: 32 |
Re: Bricked NSA320S during 2017.07 flash April 11, 2021 03:19PM |
Registered: 3 years ago Posts: 32 |
Re: Bricked NSA320S during 2017.07 flash April 11, 2021 06:25PM |
Admin Registered: 13 years ago Posts: 19,106 |
Re: Bricked NSA320S during 2017.07 flash April 12, 2021 12:03AM |
Registered: 3 years ago Posts: 32 |
Quote
bodhi Wrote:
-------------------------------------------------------
> Hi mervin,
>
> I think I need to modify the DTS to fix this problem once for all.
>
> However, as I recall the init_sata_power must be used always. Let me take sometime (in the next few days) and will upload a new DTB for you to test.
Re: Bricked NSA320S during 2017.07 flash April 12, 2021 12:25AM |
Admin Registered: 13 years ago Posts: 19,106 |
Re: Bricked NSA320S during 2017.07 flash April 12, 2021 12:39AM |
Registered: 3 years ago Posts: 32 |
root@debian:~# fdisk -l Disk /dev/mtdblock0: 1 MiB, 1048576 bytes, 2048 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/mtdblock1: 512 KiB, 524288 bytes, 1024 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes [ 101.882792][ T5] usb 1-1.1: USB disconnect, device number 4 [ 101.895765][ T76] blk_update_request: I/O error, dev sdb, sector 272936 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 0 [ 101.906886][ T76] EXT4-fs warning (device sdb1): ext4_end_bio:346: I/O error 10 writing to inode 262805 starting block 34118) [ 101.918768][ T76] Buffer I/O error on device sdb1, logical block 33861 [ 101.926169][ T76] blk_update_request: I/O error, dev sdb, sector 8796224 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 0 [ 101.937356][ T76] EXT4-fs warning (device sdb1): ext4_end_bio:346: I/O error 10 writing to inode 262736 starting block 1099529) [ 101.949372][ T76] Buffer I/O error on device sdb1, logical block 1099272 [ 101.956602][ T76] blk_update_request: I/O error, dev sdb, sector 8661848 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 0 [ 101.967745][ T76] EXT4-fs warning (device sdb1): ext4_end_bio:346: I/O error 10 writing to inode 261501 starting block 1082732) [ 101.979830][ T58] Buffer I/O error on device sdb1, logical block 1082475 [ 101.987061][ T76] blk_update_request: I/O error, dev sdb, sector 8659224 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 0 [ 101.998211][ T76] EXT4-fs warning (device sdb1): ext4_end_bio:346: I/O error 10 writing to inode 260888 starting block 1082404) [ 102.010176][ T76] Buffer I/O error on device sdb1, logical block 1082147 [ 102.017388][ T76] blk_update_request: I/O error, dev sdb, sector 8664704 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 0 [ 102.028526][ T76] EXT4-fs warning (device sdb1): ext4_end_bio:346: I/O error 10 writing to inode 260887 starting block 1083089) [ 102.040485][ T76] Buffer I/O error on device sdb1, logical block 1082832 [ 102.047634][ T93] blk_update_request: I/O error, dev sdb, sector 8662392 op 0x1:(WRITE) flags 0x0 phys_seg 1 prio class 0 [ 102.071070][ T93] EXT4-fs warning (device sdb1): ext4_end_bio:346: I/O error 10 writing to inode 260884 starting block 1082800) [ 102.094478][ T93] Buffer I/O error on device sdb1, logical block 1082543 [ 102.101569][ T76] blk_update_request: I/O error, dev sdb, sector 4196608 op 0x1:(WRITE) flags 0x3000 phys_seg 1 prio class 0 [ 102.113802][ T76] Buffer I/O error on dev sdb1, logical block 524320, lost async page write [ 102.122484][ T76] blk_update_request: I/O error, dev sdb, sector 8391048 op 0x1:(WRITE) flags 0x3000 phys_seg 1 prio class 0 [ 102.134202][ T76] Buffer I/O error on dev sdb1, logical block 1048625, lost async page write [ 102.143219][ T166] blk_update_request: I/O error, dev sdb, sector 12856160 op 0x1:(WRITE) flags 0x800 phys_seg 4 prio class 0 [ 102.158079][ T5] blk_update_request: I/O error, dev sdb, sector 8391080 op 0x1:(WRITE) flags 0x3000 phys_seg 1 prio class 0 [ 102.169842][ T166] Aborting journal on device sdb1-8. [ 102.175102][ T5] Buffer I/O error on dev sdb1, logical block 1048629, lost async page write [ 102.183744][ T166] Buffer I/O error on dev sdb1, logical block 1606659, lost sync page write [ 102.192992][ T166] JBD2: Error -5 detected when updating journal superblock for sdb1-8. [ 102.222497][ T5] JBD2: Error while async write back metadata bh 524320. [ 102.223129][ T5] JBD2: Error while async write back metadata bh 1048625. Disk /dev/sda: 931.5 GiB, 1000204886016 bytes, 1953525168 sectors Disk model: WDC WD10EAVS-00D Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0xa7810ec0 Device Boot Start End Sectors Size Id Type /dev/sda1 2048 29999103 29997056 14.3G 7 HPFS/NTFS/exFAT /dev/sda2 30001152 1953525167 1923524016 917.2G 83 Linux root@debian:~# [ 102.232114][ T5] JBD2: Error while async write back metadata bh 1048629. [ 102.574349][ T5] usb 1-1.1: new high-speed USB device number 5 using orion-ehci [ 102.739787][ T5] usb 1-1.1: New USB device found, idVendor=0951, idProduct=1665, bcdDevice= 1.00 [ 102.748855][ T5] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 102.757232][ T5] usb 1-1.1: Product: DataTraveler 2.0 [ 102.762533][ T5] usb 1-1.1: Manufacturer: Kingston [ 102.767908][ T5] usb 1-1.1: SerialNumber: 00241D8CE55DBE50595760E4 [ 102.781597][ T5] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 102.795688][ T5] scsi host3: usb-storage 1-1.1:1.0 [ 103.908781][ T93] scsi 3:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 6 [ 103.925606][ T93] sd 3:0:0:0: Attached scsi generic sg1 type 0 [ 105.521345][ T58] sd 3:0:0:0: [sdc] 30720000 512-byte logical blocks: (15.7 GB/14.6 GiB) [ 105.530699][ T58] sd 3:0:0:0: [sdc] Write Protect is off [ 105.539692][ T58] sd 3:0:0:0: [sdc] No Caching mode page found [ 105.546276][ T58] sd 3:0:0:0: [sdc] Assuming drive cache: write through [ 105.553854][ T329] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #391149: comm systemd-udevd: reading directory lblock 0 [ 105.566796][ T329] EXT4-fs (sdb1): Remounting filesystem read-only [ 105.573240][ T329] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #521337: comm systemd-udevd: reading directory lblock 0 [ 105.586064][ T329] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #391149: comm systemd-udevd: reading directory lblock 0 [ 105.598620][ T329] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #391149: comm systemd-udevd: reading directory lblock 0 [ 105.611492][ T329] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #658197: comm systemd-udevd: reading directory lblock 0 [ 105.623956][ T329] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #521270: comm systemd-udevd: reading directory lblock 0 [ 105.636506][ T58] sdc: sdc1 [ 105.639938][ T329] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #391149: comm systemd-udevd: reading directory lblock 0 [ 105.656741][ T58] sd 3:0:0:0: [sdc] Attached SCSI removable disk [ 105.668740][ T329] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #391149: comm systemd-udevd: reading directory lblock 0 [ 105.681148][ T329] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #391149: comm systemd-udevd: reading directory lblock 0 [ 105.693875][ T329] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #521269: comm systemd-udevd: reading directory lblock 0 ^C root@debian:~# [ 128.014903][ T1409] EXT4-fs error: 11 callbacks suppressed [ 128.014927][ T1409] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #391149: comm cron: reading directory lblock 0 [ 128.032208][ T1409] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #391149: comm cron: reading directory lblock 0 [ 128.043924][ T1409] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #262443: comm cron: reading directory lblock 0 [ 128.055736][ T1409] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #391149: comm cron: reading directory lblock 0 [ 128.067517][ T1409] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #391149: comm cron: reading directory lblock 0 [ 128.079293][ T1409] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #391149: comm cron: reading directory lblock 0 [ 128.091290][ T1409] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #262443: comm cron: reading directory lblock 0 shutdown -h now [ 135.894715][ T2053] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #651521: comm bash: reading directory lblock 0 [ 135.906106][ T2053] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #651521: comm bash: reading directory lblock 0 [ 135.917952][ T2053] EXT4-fs warning (device sdb1): dx_probe:757: inode #657707: lblock 0: comm bash: error -5 reading directory block [ 135.930324][ T2053] EXT4-fs warning (device sdb1): dx_probe:757: inode #657831: lblock 0: comm bash: error -5 reading directory block [ 135.942689][ T2053] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #390913: comm bash: reading directory lblock 0 [ 135.954436][ T2053] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #391049: comm bash: reading directory lblock 0 -bash: shutdown: command not found root@debian:~# shutdown -h now [ 137.364690][ T2053] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #651521: comm bash: reading directory lblock 0 [ 137.376078][ T2053] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #651521: comm bash: reading directory lblock 0 [ 137.387884][ T2053] EXT4-fs warning (device sdb1): dx_probe:757: inode #657707: lblock 0: comm bash: error -5 reading directory block [ 137.400216][ T2053] EXT4-fs warning (device sdb1): dx_probe:757: inode #657831: lblock 0: comm bash: error -5 reading directory block [ 137.412528][ T2053] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #390913: comm bash: reading directory lblock 0 [ 137.424140][ T2053] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #391049: comm bash: reading directory lblock 0 -bash: shutdown: command not found root@debian:~# shutdown -h now [ 138.604689][ T2053] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #651521: comm bash: reading directory lblock 0 [ 138.616232][ T2053] EXT4-fs error (device sdb1): __ext4_find_entry:1526: inode #651521: comm bash: reading directory lblock 0 [ 138.628053][ T2053] EXT4-fs warning (device sdb1): dx_probe:757: inode #657707: lblock 0: comm bash: error -5 reading directory block [ 138.640389][ T2053] EXT4-fs warning (device sdb1): dx_probe:757: inode #657831: lblock 0: comm bash: error -5 reading directory block -bash: shutdown: command not found root@debian:~# shutdown -h now [ 139.554781][ T2053] EXT4-fs warning (device sdb1): dx_probe:757: inode #657707: lblock 0: comm bash: error -5 reading directory block [ 139.566915][ T2053] EXT4-fs warning (device sdb1): dx_probe:757: inode #657831: lblock 0: comm bash: error -5 reading directory block -bash: shutdown: command not found root@debian:~# ▒
Re: Bricked NSA320S during 2017.07 flash April 19, 2021 04:17PM |
Registered: 3 years ago Posts: 32 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06 -0700) ZyXEL NSA310S/320S 1/2-Bay Power Media Server SoC: Kirkwood 88F6702_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 Reset IDE: Bus 0: OK Bus 1: ............OK Device 0: Model: WDC WD10EACS-22D6B0 Firm: 01.01A01 Ser#: WD-WCAU43709977 Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) Device 1: Model: WDC WD10EAVS-00D7B0 Firm: 01.01A01 Ser#: WD-WCAU41984981 Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) Partition Map for IDE device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 19997953 bf82038f-01 83 2 20000768 1933524400 bf82038f-02 83 Partition Map for IDE device 1 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 1953523120 ec2d0c47-01 83 running scan_disk ... Scan device ide Reset IDE: Bus 0: OK Bus 1: OK Device 0: Model: WDC WD10EACS-22D6B0 Firm: 01.01A01 Ser#: WD-WCAU43709977 Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) Device 1: Model: WDC WD10EAVS-00D7B0 Firm: 01.01A01 Ser#: WD-WCAU41984981 Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) device ide 0:1 1 bytes read in 57 ms (0 Bytes/s) Found bootable drive on ide 0 loading uImage ... 5350552 bytes read in 2005 ms (2.5 MiB/s) loading uInitrd ... 9609342 bytes read in 3514 ms (2.6 MiB/s) loading DTB /boot/dts/kirkwood-nsa320s.dtb ... 12594 bytes read in 70 ms (174.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.11.4-kirkwood-tld-1 Created: 2021-04-19 12:56:29 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5350488 Bytes = 5.1 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.11.4-kirkwood-tld-1 Created: 2021-04-19 12:56:37 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9609278 Bytes = 9.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f1e1000, end 0fb0b03e ... OK Loading Device Tree to 0f1da000, end 0f1e0131 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.11.4-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sun Mar 7 18:16:07 PST 2021 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Zyxel NSA320S [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env) [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 232144K/262144K available (10240K kernel code, 1544K rwdata, 4208K rodata, 1024K init, 305K bss, 30000K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x408/0x7b4 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000002][ T0] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000066][ T0] Switching to timer-based delay loop, resolution 6ns [ 0.000973][ T0] Console: colour dummy device 80x30 [ 0.001056][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.001104][ T0] pid_max: default: 32768 minimum: 301 [ 0.001556][ T0] LSM: Security Framework initializing [ 0.001763][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001816][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003420][ T0] CPU: Testing write buffer coherency: ok [ 0.005971][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.006350][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.006740][ T1] rcu: Hierarchical SRCU implementation. [ 0.008295][ T1] devtmpfs: initialized [ 0.015623][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.015687][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.060692][ T1] prandom32: self test passed (less than 6 bits correlated) [ 0.060742][ T1] prandom: seed boundary self test passed [ 0.065790][ T1] prandom: 100 self tests passed [ 0.065812][ T1] pinctrl core: initialized pinctrl subsystem [ 0.067565][ T1] NET: Registered protocol family 16 [ 0.068407][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.069477][ T1] audit: initializing netlink subsys (disabled) [ 0.071139][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.071564][ T16] audit: type=2000 audit(0.060:1): state=initialized audit_enabled=0 res=1 [ 0.071749][ T1] cpuidle: using governor ladder [ 0.071859][ T1] cpuidle: using governor menu [ 0.072469][ T1] Feroceon L2: Enabling L2 [ 0.072529][ T1] Feroceon L2: Cache support initialised. [ 0.084917][ T1] No ATAGs? [ 2.560073][ C0] random: fast init done [ 5.947081][ T39] "cryptomgr_test" (39) uses obsolete ecb(arc4) skcipher [ 6.170340][ T1] raid6: int32x8 gen() 93 MB/s [ 6.340227][ T1] raid6: int32x8 xor() 57 MB/s [ 6.510335][ T1] raid6: int32x4 gen() 94 MB/s [ 6.680266][ T1] raid6: int32x4 xor() 61 MB/s [ 6.850110][ T1] raid6: int32x2 gen() 121 MB/s [ 7.020147][ T1] raid6: int32x2 xor() 72 MB/s [ 7.190255][ T1] raid6: int32x1 gen() 93 MB/s [ 7.360301][ T1] raid6: int32x1 xor() 54 MB/s [ 7.360322][ T1] raid6: using algorithm int32x2 gen() 121 MB/s [ 7.360339][ T1] raid6: .... xor() 72 MB/s, rmw enabled [ 7.360353][ T1] raid6: using intx1 recovery algorithm [ 7.360648][ T1] vgaarb: loaded [ 7.361291][ T1] SCSI subsystem initialized [ 7.361861][ T1] usbcore: registered new interface driver usbfs [ 7.361958][ T1] usbcore: registered new interface driver hub [ 7.362037][ T1] usbcore: registered new device driver usb [ 7.362273][ T1] pps_core: LinuxPPS API ver. 1 registered [ 7.362292][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 7.362331][ T1] PTP clock support registered [ 7.364316][ T1] clocksource: Switched to clocksource orion_clocksource [ 7.465019][ T1] VFS: Disk quotas dquot_6.6.0 [ 7.465154][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 7.484973][ T1] NET: Registered protocol family 2 [ 7.494863][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 7.494927][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 7.494980][ T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 7.495027][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 7.495275][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 7.495361][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 7.495405][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 7.495668][ T1] NET: Registered protocol family 1 [ 7.496486][ T1] RPC: Registered named UNIX socket transport module. [ 7.496513][ T1] RPC: Registered udp transport module. [ 7.496528][ T1] RPC: Registered tcp transport module. [ 7.496542][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 7.496562][ T1] PCI: CLS 0 bytes, default 32 [ 7.496916][ T1] Trying to unpack rootfs image as initramfs... [ 9.434785][ T1] Freeing initrd memory: 9388K [ 9.435016][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 10.231400][ T1] Initialise system trusted keyrings [ 10.231483][ T1] Key type blacklist registered [ 10.231757][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 10.231899][ T1] zbud: loaded [ 10.233536][ T1] NFS: Registering the id_resolver key type [ 10.233589][ T1] Key type id_resolver registered [ 10.233607][ T1] Key type id_legacy registered [ 10.233657][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 10.233687][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 10.234006][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 10.234658][ T1] fuse: init (API version 7.33) [ 10.235130][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 10.235387][ T1] orangefs_init: module version upstream loaded [ 10.235410][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 10.354467][ T1] xor: measuring software checksum speed [ 10.365186][ T1] arm4regs : 927 MB/sec [ 10.382947][ T1] 8regs : 556 MB/sec [ 10.395202][ T1] 32regs : 809 MB/sec [ 10.395224][ T1] xor: using function: arm4regs (927 MB/sec) [ 10.395250][ T1] async_tx: api initialized (async) [ 10.395274][ T1] Key type asymmetric registered [ 10.395290][ T1] Asymmetric key parser 'x509' registered [ 10.395361][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 10.395513][ T1] io scheduler bfq registered [ 10.634819][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 10.637084][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges: [ 10.637191][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 [ 10.637247][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 10.637288][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 10.637636][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 10.637666][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 10.637697][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) [ 10.637724][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 10.637749][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 10.637913][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 10.637960][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 10.639731][ T1] PCI: bus0: Fast back to back transfers disabled [ 10.639774][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 10.641331][ T1] PCI: bus1: Fast back to back transfers enabled [ 10.641369][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 10.641616][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe00007ff pref] [ 10.641651][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 10.642482][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 10.705647][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 10.708691][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 10.765606][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 10.768922][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 10.770560][ T1] printk: console [ttyS0] disabled [ 10.770676][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 10416666) is a 16550A [ 11.721601][ T1] printk: console [ttyS0] enabled [ 11.736164][ T1] loop: module loaded [ 11.740919][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 11.750633][ T1] scsi host0: sata_mv [ 11.755246][ T1] scsi host1: sata_mv [ 11.759369][ T1] ata1: SATA max UDMA/133 irq 32 [ 11.764157][ T1] ata2: SATA max UDMA/133 irq 32 [ 11.770465][ T1] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1 [ 11.777608][ T1] nand: Eon NAND 128MiB 3,3V 8-bit [ 11.782558][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 11.790891][ T1] Scanning device for bad blocks [ 11.800833][ T1] Bad eraseblock 100 at 0x000000c80000 [ 11.811265][ T1] Bad eraseblock 200 at 0x000001900000 [ 11.858418][ T1] 2 cmdlinepart partitions found on MTD device orion_nand [ 11.865376][ T1] Creating 2 MTD partitions on "orion_nand": [ 11.871192][ T1] 0x000000000000-0x000000100000 : "uboot" [ 11.878435][ T1] 0x000000100000-0x000000180000 : "uboot_env" [ 11.886543][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 11.895086][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 11.906872][ T1] libphy: Fixed MDIO Bus: probed [ 11.913304][ T1] libphy: orion_mdio_bus: probed [ 11.918146][ T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@1: Whitelisted compatible string. Please remove [ 11.948668][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 11.958203][ T1] mv643xx_eth: Set the PHY to fix link down [ 11.958960][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 4c:9e:ff:0b:73:72 [ 11.974473][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.981708][ T1] ehci-pci: EHCI PCI platform driver [ 11.987020][ T1] ehci-orion: EHCI orion driver [ 11.991960][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 11.998274][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 12.006874][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 12.034347][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 12.041387][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.11 [ 12.050374][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.058316][ T1] usb usb1: Product: EHCI Host Controller [ 12.063908][ T1] usb usb1: Manufacturer: Linux 5.11.4-kirkwood-tld-1 ehci_hcd [ 12.071324][ T1] usb usb1: SerialNumber: f1050000.ehci [ 12.077501][ T1] hub 1-0:1.0: USB hub found [ 12.082029][ T1] hub 1-0:1.0: 1 port detected [ 12.087687][ T1] usbcore: registered new interface driver usb-storage [ 12.094981][ T1] mousedev: PS/2 mouse device common for all mice [ 12.101556][ T1] i2c /dev entries driver [ 12.106622][ T1] i2c i2c-0: Not using recovery: no recover_bus() found [ 12.115344][ T1] ht1382 0-0068: registered as rtc0 [ 12.121463][ T1] ht1382 0-0068: setting system clock to 2021-04-19T13:00:34 UTC (1618837234) [ 12.131483][ T1] device-mapper: uevent: version 1.0.3 [ 12.137171][ T1] device-mapper: ioctl: 4.43.0-ioctl (2020-10-01) initialised: dm-devel@redhat.com [ 12.146833][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 12.154038][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 12.161394][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 12.168815][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 12.175613][ T1] device-mapper: raid: Loading target version 1.15.1 [ 12.184917][ T1] hid: raw HID events driver (C) Jiri Kosina [ 12.191157][ T1] drop_monitor: Initializing network drop monitor service [ 12.198806][ T1] NET: Registered protocol family 10 [ 12.205413][ T1] Segment Routing with IPv6 [ 12.209764][ T1] RPL Segment Routing with IPv6 [ 12.214617][ T1] NET: Registered protocol family 17 [ 12.219992][ T1] Key type dns_resolver registered [ 12.225586][ T1] registered taskstats version 1 [ 12.230375][ T1] Loading compiled-in X.509 certificates [ 12.236337][ T1] zswap: loaded using pool lzo/zbud [ 12.241766][ T1] Key type ._fscrypt registered [ 12.246554][ T1] Key type .fscrypt registered [ 12.251159][ T1] Key type fscrypt-provisioning registered [ 12.258925][ T1] Key type big_key registered [ 12.264409][ T89] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 12.306504][ T1] Key type encrypted registered [ 12.314579][ T89] ata1.00: ATA-8: WDC WD10EACS-22D6B0, 01.01A01, max UDMA/133 [ 12.321885][ T89] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 12.334705][ T89] ata1.00: configured for UDMA/133 [ 12.350253][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD10EACS-22D 1A01 PQ: 0 ANSI: 5 [ 12.360512][ T93] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 12.369478][ T93] sd 0:0:0:0: [sda] Write Protect is off [ 12.375197][ T93] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 12.387790][ T93] sda: sda1 sda2 [ 12.393190][ T93] sd 0:0:0:0: [sda] Attached SCSI disk [ 12.454349][ T100] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 12.656264][ T100] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.32 [ 12.665174][ T100] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 12.673029][ T100] usb 1-1: Product: USB2.0 Hub [ 12.678606][ T100] hub 1-1:1.0: USB hub found [ 12.683382][ T100] hub 1-1:1.0: 4 ports detected [ 13.014360][ T91] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 13.384404][ T91] ata2.00: ATA-8: WDC WD10EAVS-00D7B0, 01.01A01, max UDMA/133 [ 13.391699][ T91] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 13.403898][ T91] ata2.00: configured for UDMA/133 [ 13.419450][ T58] scsi 1:0:0:0: Direct-Access ATA WDC WD10EAVS-00D 1A01 PQ: 0 ANSI: 5 [ 13.429569][ T93] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 13.438384][ T93] sd 1:0:0:0: [sdb] Write Protect is off [ 13.444005][ T93] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 13.457260][ T93] sdb: sdb1 [ 13.461980][ T93] sd 1:0:0:0: [sdb] Attached SCSI disk [ 13.470415][ T1] Freeing unused kernel memory: 1024K [ 13.476693][ T1] Checked W+X mappings: passed, no W+X pages found [ 13.483046][ T1] Run /init as init process Loading, please wait... Starting version 241 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 26.346846][ T149] process '/usr/bin/fstype' started with executable stack Begin: Will now check root file system ... fsck from util-linux 2.33.1 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 rootfs: clean, 18068/625856 files, 311880/2499744 blocks done. [ 26.812242][ T158] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 26.841489][ T158] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Starting hotplug events dispatcher: systemd-udevd. [ ok ] Synthesizing the initial hotplug events (subsystems)...done. [....] Synthesizing the initial hotplug events (devices)...[ 30.647275][ T345] input: gpio_keys as /devices/platform/gpio_keys/input/input0 done. [....] Waiting for /dev to be fully populated...[ 30.797889][ T347] systemd-udevd[347]: Using default interface naming scheme 'v240'. [ 30.960892][ T347] systemd-udevd[347]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 31.104558][ T367] orion_wdt: Initial timeout 25 sec [ 31.375787][ T347] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 31.456070][ T347] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 31.586816][ C0] random: crng init done [ 31.727855][ T348] marvell-cesa f1030000.crypto: CESA device successfully registered [ 31.831255][ T365] systemd-udevd[365]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. done. [ ok ] Setting hostname to 'debian'...done. [ ok ] Activating swap:. [ 34.814616][ T567] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro. Quota mode: none. [info] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Starting Setting kernel variables: sysctl. [ ok ] Initializing random number generator...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/4c:9e:ff:0b:73:72 Sending on LPF/eth0/4c:9e:ff:0b:73:72 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 [ 39.361909][ T1091] mv643xx_eth: Set the PHY back to auto-negotiation mode [ 41.493378][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled [ 41.510698][ T100] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 DHCPOFFER of 192.168.100.11 from 192.168.100.100 DHCPREQUEST for 192.168.100.11 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.100.11 from 192.168.100.100 bound to 192.168.100.11 -- renewal in 528646380 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1324 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1351 (klogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 10 debian ttyS0 debian login: root Password: Last login: Mon Apr 19 05:49:24 PDT 2021 on ttyS0 Linux debian 5.11.4-kirkwood-tld-1 #1.0 PREEMPT Sun Mar 7 18:16:07 PST 2021 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# fdisk -l Disk /dev/mtdblock0: 1 MiB, 1048576 bytes, 2048 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/mtdblock1: 512 KiB, 524288 bytes, 1024 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/sda: 931.5 GiB, 1000204886016 bytes, 1953525168 sectors Disk model: WDC WD10EACS-22D Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0xbf82038f Device Boot Start End Sectors Size Id Type /dev/sda1 2048 20000000 19997953 9.5G 83 Linux /dev/sda2 20000768 1953525167 1933524400 922G 83 Linux Disk /dev/sdb: 931.5 GiB, 1000204886016 bytes, 1953525168 sectors Disk model: WDC WD10EAVS-00D Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0xec2d0c47 Device Boot Start End Sectors Size Id Type /dev/sdb1 2048 1953525167 1953523120 931.5G 83 Linux root@debian:~# e2label /dev/sda1 rootfs root@debian:~# e2label /dev/sdb1 DISK2
Re: Bricked NSA320S during 2017.07 flash April 19, 2021 05:22PM |
Admin Registered: 13 years ago Posts: 19,106 |
Re: Bricked NSA320S during 2017.07 flash April 20, 2021 04:50AM |
Registered: 3 years ago Posts: 32 |
Re: Bricked NSA320S during 2017.07 flash April 20, 2021 03:49PM |
Admin Registered: 13 years ago Posts: 19,106 |
Re: Bricked NSA320S during 2017.07 flash April 21, 2021 06:58AM |
Registered: 3 years ago Posts: 32 |
Re: Bricked NSA320S during 2017.07 flash April 22, 2021 08:52PM |
Admin Registered: 13 years ago Posts: 19,106 |
Re: Bricked NSA320S during 2017.07 flash August 01, 2023 01:55AM |
Registered: 3 years ago Posts: 20 |
Re: Bricked NSA320S during 2017.07 flash December 03, 2023 02:42PM |
Admin Registered: 13 years ago Posts: 19,106 |
Quote
[ 7.747243] mtd: no closing ) found in partition name
dmesg | grep -2 mtdparts dmesg | grep -2 0x0 cat /proc/mtd
Re: Bricked NSA320S during 2017.07 flash December 03, 2023 03:51PM |
Registered: 9 years ago Posts: 465 |