doblecero
Problem installing NSA320 u-boot - continued March 07, 2018 06:15PM |
fw_setenv mtdparts 'xxxxxxxxx'since I didn't had that variable in the backup i took of the environment before, so I just didn't run that.
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:46:11 -0700) ZyXEL NSA320 2-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: OK Device 0: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC4N6UX02JH Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) Device 1: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC4N5JCKKV6 Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) Unknown command 'mmc' - try 'help' ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** Bad device usb 0 ** Partition Map for IDE device 0 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000800 0x000f3fff "mitraswap" attrs: 0x0000000000000000 type: 0657fd6d-a4ab-43c4-84e5-0933c84b4f4f type: swap guid: 8a6ebe8b-87c9-4dc7-9a85-9f670ef809cf 2 0x000f4000 0x15d509fff "eexxtt44" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 type: data guid: 9a279fa3-46de-4fae-b268-e4e15c6064b3 Partition Map for IDE device 1 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000800 0x000f3fff "mitraswap" attrs: 0x0000000000000000 type: 0657fd6d-a4ab-43c4-84e5-0933c84b4f4f type: swap guid: 31d9fc6d-19db-4264-b8e1-e7f43baed572 2 0x000f4000 0x15d509fff "eexxtt44" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 type: data guid: b2806883-140c-4bcc-bfdf-39b4a6603f0b Unknown command 'mmc' - try 'help' running scan_disk ... Scan device usb device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Reset IDE: Bus 0: OK Bus 1: OK Device 0: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC4N6UX02JH Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) Device 1: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC4N5JCKKV6 Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) device ide 0:1 ** File not found /boot/uImage ** device ide 1:1 Failed to mount ext2 filesystem... ** Unrecognized filesystem type ** device ide 2:1 ** Bad device ide 2 ** device ide 3:1 ** Bad device ide 3 ** Scan device mmc Unknown command 'mmc' - try 'help' device mmc 0:1 ** Bad device mmc 0 ** device mmc 1:1 ** Bad device mmc 1 ** device mmc 2:1 ** Bad device mmc 2 ** device mmc 3:1 ** Bad device mmc 3 ** loading uImage ... ** Bad device usb 0 ** loading uInitrd ... ** Bad device usb 0 ** loading DTB /boot/dts/kirkwood-nsa320.dtb ... ** Bad device usb 0 ** Wrong Image Format for bootm command Error occured, error code = 112 ERROR: can't get kernel image! NSA320>
arcNumber=3956 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-nsa320.dtb ethact=egiga0 ethaddr=MY_MAC_IN_RIGHT_FORMAT fileaddr=1c00000 filesize=0 if_netconsole=ping $serverip init_ide=ide reset init_mmc=mmc rescan init_usb=usb start ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done scan_ide=ide reset scan_mmc=mmc rescan scan_usb=usb start serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_loaded=0 uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 3144/131068 bytes
Re: Problem installing NSA320 u-boot - continued March 07, 2018 07:05PM |
Admin Registered: 13 years ago Posts: 18,594 |
Quote
3. Be sure to save your current uBoot image in mtd0, or have a backup image saved somewhere as precaution. And save your current u-boot envs with fw_printenv, or just copy/paste the listing into a text file. Note the nanddump command below allows future restoration to the same box you're backing up, and also can be used to restore a differrent box's mtd0 if needed.
Dumping NAND mtd0:
nanddump --noecc --omitoob -l 0x80000 -f mtd0 /dev/mtd0
doblecero
Re: Problem installing NSA320 u-boot - continued March 08, 2018 03:12AM |
flash_erase /dev/mtd0 0 4 nandwrite /dev/mtd0 mtd0_backup_uboot
Re: Problem installing NSA320 u-boot - continued March 08, 2018 03:45AM |
Admin Registered: 13 years ago Posts: 18,594 |
> flash_erase /dev/mtd0 0 4 > nandwrite /dev/mtd0 mtd0_backup_uboot >>
Re: Problem installing NSA320 u-boot - continued March 11, 2018 10:15AM |
Registered: 6 years ago Posts: 1 |
Re: Problem installing NSA320 u-boot - continued March 11, 2018 05:19PM |
Admin Registered: 13 years ago Posts: 18,594 |