Welcome! Log In Create A New Profile

Advanced

UART Boot DNS-320 B1 with broken NAND

Posted by Ironaxe 
Re: UART Boot DNS-320 B1 with broken NAND
November 22, 2018 04:32PM
Ironaxe,

> Nope. Cant get to the Marvell prompt.

Try kwboot with the new NSA310S or Pogo V4 uboot. See if it can get pass the NAND error.

If you cannot get pass the NAND error, and cannot find correct NAND to install, I might be able to turn NAND off completely in a special build u-boot version for either NSA310S or Pogo V4.

But kwboot is important, to know that it works loading the image and start running.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: UART Boot DNS-320 B1 with broken NAND
November 23, 2018 02:40PM
Hi, the 310s and PogoV4 uboot you linked in your first post ( 2017.07 ) dont work for me.
Still stuck after sending.
Re: UART Boot DNS-320 B1 with broken NAND
November 23, 2018 03:49PM
Ironaxe,

> Hi, the 310s and PogoV4 uboot you linked in your
> first post ( 2017.07 ) dont work for me.
> Still stuck after sending.

Thanks. Then we know that the u-boot image header for NSA310S and Pogo V4 cannot be used. So the solution is back to either correct NAND chip or new u-boot for this box.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: UART Boot DNS-320 B1 with broken NAND
November 24, 2018 04:13PM
Btw.
Is it possible to write an u-boot Image to NAND from the Marvell>> Prompt ?
( nand write )
And where can i put the File besides from TFTP ? USB Maybe ?
Re: UART Boot DNS-320 B1 with broken NAND
November 24, 2018 04:38PM
Ironaxe,

> Is it possible to write an u-boot Image to NAND
> from the Marvell>> Prompt ?
> ( nand write )

Yes. Load into memory and nandwrite from there.

> And where can i put the File besides from TFTP ?
> USB Maybe ?

USB should work.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: UART Boot DNS-320 B1 with broken NAND
November 25, 2018 02:02AM
Can you help with the command?
Or point me to some Help to read?
Re: UART Boot DNS-320 B1 with broken NAND
November 25, 2018 02:29AM
Ironaxe,

Sure. it is similar to section B in this post in the Wiki thread:

Quote

Backup and Restore NAND mtds - Pogoplug V4 original MTD partitions

https://forum.doozan.com/read.php?3,16789,16789#msg-16789

You need to adjust the u-boot mtd0 name, and size for this box, and making sure that the mtdparts are defined correcly. Step 1 is for kwboot, so it is not applicable. Step 2 and the rest are relevant.

You could list the commands you about to run here, I can double check for you.


Quote

B. How to restore NAND in Serial Console:
==================================


Here is what to do if you've decided that you need to restore NAND mtd0 in serial console to go back to stock OS. Assuming only mtd0 was messed up (that's how it usually happens). If the entire NAND was messed up, then use this procedure to restore mtd0 and then calculate the offset and size of the rest of the other mtds. If you're not sure, pls post questions in this thread.

Caveats: This is something I would not recommend doing, unless you can no loger boot into Debian or Arch. Because If you can use kwboot to boot the box, then you can boot Debian or Arch quite easily, without doing this procedure. See the Debian kernel/rootfs thread for how to create the Debian 4.4 rootfs to use with this box.

The procedure below has a lot more risk of errors occurred than flashing NAND mtd0 from Linux command line (section A).

Prerequisites

r1. This procedure requires a working serial console connected to the Pogo V4. And knowledge how to use kwboot to boot the latest version of u-boot.

r2. Download the latest u-boot, and kwboot binary as described in the u-boot thread to the serial console server (where you run kwboot). Create a single partition, type Ext3, USB thumbdrive. Copy your backup mtd0 to this USB drive root folder. Plug this USB drive into the Pogo V4 top USB port.

Restore NAND mtd0

1. Connect serial console and use kwboot to boot the Pogo V4. See davygravy instruction for more details. I'm assume that you already know how to use kwboot.

Run kwboot and interrupt serial console when you see the countdown:
./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2016.05-tld-1.pogo_v4.mtd0.kwb -p
Expected output
Sending boot message. Please reboot the target...-
Sending boot image...
0 % [......................................................................]
<snip>
95 % [......................................................................]
97 % [......................................................................]
99 % [....................................]
[Type Ctrl-\ + c to quit]

U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:41:47 -0700)
Pogoplug V4

SoC: Kirkwood 88F6192_A1
DRAM: 128 MiB
WARNING: Caches not enabled
NAND: 128 MiB
MMC: kwsdio: 0
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0


2. Verify the mtdparts is correct for Pogo V4

mtdparts
Expected output

device nand0 <orion_nand>, # parts = 5
#: name size offset mask_flags
0: u-boot 0x00200000 0x00000000 0
1: uImage 0x00300000 0x00200000 0
2: uImage2 0x00300000 0x00500000 0
3: failsafe 0x00800000 0x00800000 0
4: root 0x07000000 0x01000000 0

active partition: nand0,2 - (uImage2) 0x00300000 @ 0x00500000

defaults:
mtdids : none
mtdparts: none

3. Start the USB drive

usb start
Expected output

starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found

4. Load the backup mtd0. Here the stock mtd0 backup file name was mtd0.pogo_v4

ext2load usb 0:1 0x800000 /mtd0.pogo_v4
Expected output
2097152 bytes read in 1318 ms (1.5 MiB/s)


5. Erase mtd0

nand erase 0x0 0x200000
Expected output
NAND erase: device 0 offset 0x0, size 0x200000
Erasing at 0x1e0000 -- 100% complete.
OK

6. Flash mtd0.pogo_v4 to NAND mtd0

nand write 0x800000 0x0 0x200000
Expected output

NAND write: device 0 offset 0x0, size 0x200000
2097152 bytes written: OK

7. Reset the box to boot with stock u-boot
reset
Expected output:

The stock u-boot banner and other info. And then it will proceeed to boot stock OS.

DONE.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: UART Boot DNS-320 B1 with broken NAND
November 25, 2018 11:36AM
Thx. But mtdparts are not defined in the default configuration.
Re: UART Boot DNS-320 B1 with broken NAND
November 25, 2018 12:27PM
Ironaxe Wrote:
-------------------------------------------------------
> Thx. But mtdparts are not defined in the default
> configuration.

Interrupt serial console and list all commands:

help

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: UART Boot DNS-320 B1 with broken NAND
November 25, 2018 01:38PM
Marvell>> mtdparts
mtdids not defined, no default present



Marvell>> help
?       - alias for 'help'
SatR - sample at reset sub-system, relevent for DB only
base    - print or set address offset
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootext2    dev:boot_part1,boot_part2 addr boot_image linux_dev_name
bootm   - boot application image from memory
bootp   - boot image via network using BootP/TFTP protocol
bubt    - Burn an image on the Boot Nand Flash.
chpart  - change active partition
cmp     - memory compare
cmpm    - Compare Memory
cp      - memory copy
cpumap - Display CPU memory mapping settings.
crc32   - checksum calculation
date    - get/set/reset date & time
dclk    - Display the MV device CLKs.
dhcp    - invoke DHCP client to obtain IP/boot params
diskboot- boot from IDE device
echo    - echo args to console
eeprom  - EEPROM sub-system
erase   - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fi      - Find value in the memory.
flinfo  - print FLASH memory information
fsinfo  - print information about filesystems
fsload  - load binary file from a filesystem image
g       - start application at cached address 'addr'(default addr 0x40000)
go      - start application at address 'addr'
help    - print online help
icrc32  - checksum calculation
ide     - IDE sub-system
iloop   - infinite loop on address range
imd     - i2c memory display
iminfo  - print header information for application image
imm[.b, .s, .w, .l]     - i2c memory modify (auto-incrementing)
imw     - memory write (fill)
inm     - memory modify (constant address)
iprobe  - probe to discover valid I2C chip addresses
ir      - reading and changing MV internal register values.
loop    - infinite loop on address range
ls      - list files in a directory (default /)
map     - Diasplay address decode windows
md      - memory display
me      - PCI master enable
mm      - memory modify (auto-incrementing)
mmcinit - init mmc card
mp      - map PCI BAR
mtdparts- define flash/nand partitions
mtest   - simple RAM test
mw      - memory write (fill)
nand                   - NAND sub-system
nboot   - boot from NAND device
nbubt   - Burn a boot loader image on the Boot Nand Flash.
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
phyRead - Read PCI-E Phy register
pciePhyWrite    - Write PCI-E Phy register
phyRead - Read Phy register
phyWrite        - Write Phy register
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
rcvr    - Satrt recovery process (Distress Beacon with TFTP server)
reset   - Perform RESET of the CPU
resetenv        - Return all environment variable to default.
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
se      - PCI Slave enable
setenv  - set environment variables
sflash  - read, write or erase the external SPI Flash.
sg      - scanning the PHYs status
sp      - Scan PCI bus.
switchRegRead   - Read switch register
switchRegWrite  - Write switch register
Temp    - read chip Tj temp
tftpboot- boot image via network using TFTP protocol
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor version
Marvell>>

Re: UART Boot DNS-320 B1 with broken NAND
November 25, 2018 02:41PM
And,

printenv

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: UART Boot DNS-320 B1 with broken NAND
November 26, 2018 05:46AM
Marvell>> printenv      
bootargs=root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none
bootcmd=nand read.e 0xa00000 0x100000 0x300000;nand read.e 0xf00000 0x600000 0x300000;bootm 0xa00000 0xf00000
baudrate=115200
loads_echo=0
ipaddr=2.66.66.201
serverip=2.66.66.32
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
MALLOC_len=1
ethprime=egiga0
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
bootdelay=1
disaMvPnp=no
ethaddr=00:50:43:00:02:02
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
enaAutoRecovery=yes
pcieTune=no
ethact=egiga0

Environment size: 1272/131068 bytes
Marvell>> 
Re: UART Boot DNS-320 B1 with broken NAND
November 26, 2018 04:44PM
Ironaxe,

From the look of your bootcmd, and bootargs, I think it is safe to flash.
bootcmd=nand read.e 0xa00000 0x100000 0x300000;nand read.e 0xf00000 0x600000 0x300000;bootm 0xa00000 0xf00000
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)

However, usually we want to take extra precaution to make sure the MTD parts layout looks sane before doing it.
setenv mtdids 'nand0=nand_mtd'
setenv mtdparts 'mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)'

and then execute mtdparts command to see if they are recognized:
mtdparts

And then, if it looks OK. We want to make sure the nand write flashing command in the example matches what you have. So you can list the commands you about to run here for doublecheck.

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 1 time(s). Last edit at 11/26/2018 04:47PM by bodhi.
Re: UART Boot DNS-320 B1 with broken NAND
November 27, 2018 05:56AM
After
setenv........

Marvell>> mtdparts

device nand0 <nand_mtd>, # parts = 2
 #: name			size		offset		mask_flags
 0: uboot               0x000c0000	0x00000000	1
 1: root                0x07f00000	0x00100000	0

active partition: nand0,0 - (uboot) 0x000c0000 @ 0x00000000

defaults:
mtdids  : <NULL>
mtdparts: <NULL>

I would do:

usb start
......
fatload usb 0:1 0x800000 /mtd0.dns-320
......
nand erase 0x0 0x100000 ( 1MB U-Boot File )
......
nand write 0x800000 0x0 0x100000

Maybe change
setenv mtdparts 'mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)'
to
setenv mtdparts 'mtdparts=nand_mtd:0x100000@0(uboot)ro,0x7f00000@0x100000(root)'
??



Edited 2 time(s). Last edit at 11/27/2018 05:58AM by Ironaxe.
Re: UART Boot DNS-320 B1 with broken NAND
November 27, 2018 01:07PM
Ironaxe,

> Marvell>> mtdparts
>
> device nand0 <nand_mtd>, # parts = 2
> #: name size offset mask_flags
> 0: uboot 0x000c0000 0x00000000 1
> 1: root 0x07f00000 0x00100000 0
>
> active partition: nand0,0 - (uboot) 0x000c0000 @
> 0x00000000


Looks good!

> defaults:
> mtdids : <NULL>
> mtdparts: <NULL>

We don't need this.


> usb start
> ......
> fatload usb 0:1 0x800000 /mtd0.dns-320


fatload should work, or use ext2load if the USB is formatted as EXT2 or EXT3.


> ......
> nand erase 0x0 0x100000 ( 1MB U-Boot File )
> ......
> nand write 0x800000 0x0 0x100000

Looks good.


> Maybe change
>
> setenv mtdparts
> 'mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)'
>
> to
>
> setenv mtdparts
> 'mtdparts=nand_mtd:0x100000@0(uboot)ro,0x7f00000@0x100000(root)'
>

Don't change mtd layout, use stock definition 0xc0000 to make sure (no need to change).

setenv mtdparts 'mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)'

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: UART Boot DNS-320 B1 with broken NAND
November 27, 2018 01:21PM
OK.
Tried the above. But the Box does not boot itself without kwboot. :(
Re: UART Boot DNS-320 B1 with broken NAND
November 27, 2018 08:38PM
Ironaxe Wrote:
-------------------------------------------------------
> OK.
> Tried the above.

Can you post the serial console log of the actual flashing?

> But the Box does not boot itself

What is the behavior? Does it ouput anything when you power up?

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: UART Boot DNS-320 B1 with broken NAND
November 28, 2018 05:36AM
Marvell>> setenv mtdids 'nand0=nand_mtd'
Marvell>> setenv mtdparts 'mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)'
Marvell>> mtdparts

device nand0 <nand_mtd>, # parts = 2
 #: name			size		offset		mask_flags
 0: uboot               0x000c0000	0x00000000	1
 1: root                0x07f00000	0x00100000	0

active partition: nand0,0 - (uboot) 0x000c0000 @ 0x00000000

defaults:
mtdids  : <NULL>
mtdparts: <NULL>
Marvell>> usb start
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
Marvell>> fatload usb 0:1 0x800000 /mtd0.dns-320
reading /mtd0.dns-320
......................................................................................................

1048576 bytes read
Marvell>> nand erase 0x0 0x100000

NAND erase: device 0 offset 0x0, size 0x100000
Erasing at 0xe0000 -- 100% complete.
OK
Marvell>> nand write 0x800000 0x0 0x100000

NAND write: device 0 offset 0x0, size 0x100000
load addr ....  =800000
1048576 bytes written: OK

Looks ok to me ^^

No Output on Power up. Just a Blinking Power LED.



Edited 2 time(s). Last edit at 11/28/2018 06:07AM by Ironaxe.
Re: UART Boot DNS-320 B1 with broken NAND
November 28, 2018 04:04PM
> Marvell>> fatload usb 0:1 0x800000 /mtd0.dns-320

Try kwboot the brick box with this file mtd0.dns-320.

Interrupt serial console after it was loaded and run. And

ver
help  
printenv
setenv mtdids 'nand0=nand_mtd'
setenv mtdparts 'mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)'
mtdparts

Please post entire serial console log here (from kwboot command till the last line on the screen).

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: UART Boot DNS-320 B1 with broken NAND
November 29, 2018 02:41AM
Im using the mtd0.dns-320 with kwboot.
( was the only File that worked so far )

root@debian:/u-boot# ./tools/kwboot -t -B 115200 /dev/ttyUSB0 -b mtd0.dns-320 -p
Sending boot message. Please reboot the target.../
Sending boot image...
  0 % [......................................................................]
  0 % [......................................................................]
  1 % [......................................................................]
  2 % [......................................................................]
 .....
 98 % [......................................................................]
 99 % [......................................................................]
 99 % [..]
[Type Ctrl-\ + c to quit]


 ** MARVELL BOARD: DB-88F6702A-BP LE 

U-Boot 1.1.4 (Apr 19 2012 - 11:21:19) Marvell version: 3.6.0.DNS-320B.01

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 166Mhz 

DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB 
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled 
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0 
Marvell>> ver         

U-Boot 1.1.4 (Apr 19 2012 - 11:21:19) Marvell version: 3.6.0.DNS-320B.01
Marvell>> help
?       - alias for 'help'
SatR - sample at reset sub-system, relevent for DB only
base    - print or set address offset
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootext2    dev:boot_part1,boot_part2 addr boot_image linux_dev_name 
bootm   - boot application image from memory
bootp	- boot image via network using BootP/TFTP protocol
bubt	- Burn an image on the Boot Nand Flash.
chpart	- change active partition
cmp     - memory compare
cmpm	- Compare Memory
cp      - memory copy
cpumap - Display CPU memory mapping settings.
crc32   - checksum calculation
date    - get/set/reset date & time
dclk	- Display the MV device CLKs.
dhcp	- invoke DHCP client to obtain IP/boot params
diskboot- boot from IDE device
echo    - echo args to console
eeprom  - EEPROM sub-system
erase   - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fi	- Find value in the memory.
flinfo  - print FLASH memory information
fsinfo	- print information about filesystems
fsload	- load binary file from a filesystem image
g	- start application at cached address 'addr'(default addr 0x40000)
go      - start application at address 'addr'
help    - print online help
icrc32  - checksum calculation
ide     - IDE sub-system
iloop   - infinite loop on address range
imd     - i2c memory display
iminfo  - print header information for application image
imm[.b, .s, .w, .l]     - i2c memory modify (auto-incrementing)
imw     - memory write (fill)
inm     - memory modify (constant address)
iprobe  - probe to discover valid I2C chip addresses
ir	- reading and changing MV internal register values.
loop    - infinite loop on address range
ls	- list files in a directory (default /)
map	- Diasplay address decode windows
md      - memory display
me	- PCI master enable
mm      - memory modify (auto-incrementing)
mmcinit - init mmc card
mp	- map PCI BAR
mtdparts- define flash/nand partitions
mtest   - simple RAM test
mw      - memory write (fill)
nand                   - NAND sub-system
nboot   - boot from NAND device
nbubt	- Burn a boot loader image on the Boot Nand Flash.
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
phyRead	- Read PCI-E Phy register
pciePhyWrite	- Write PCI-E Phy register
phyRead	- Read Phy register
phyWrite	- Write Phy register
ping	- send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
rcvr	- Satrt recovery process (Distress Beacon with TFTP server)
reset   - Perform RESET of the CPU
resetenv	- Return all environment variable to default.
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
se	- PCI Slave enable
setenv  - set environment variables
sflash	- read, write or erase the external SPI Flash.
sg	- scanning the PHYs status
sp	- Scan PCI bus.
switchRegRead	- Read switch register
switchRegWrite	- Write switch register
Temp	- read chip Tj temp
tftpboot- boot image via network using TFTP protocol
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor version
Marvell>> printenv
bootargs=root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none
bootcmd=nand read.e 0xa00000 0x100000 0x300000;nand read.e 0xf00000 0x600000 0x300000;bootm 0xa00000 0xf00000
baudrate=115200
loads_echo=0
ipaddr=2.66.66.201
serverip=2.66.66.32
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
MALLOC_len=1
ethprime=egiga0
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
bootdelay=1
disaMvPnp=no
ethaddr=00:50:43:00:02:02
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
enaAutoRecovery=yes
pcieTune=no
ethact=egiga0

Environment size: 1272/131068 bytes
Marvell>> setenv mtdids 'nand0=nand_mtd'
Marvell>> setenv mtdparts 'mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)'
Marvell>> mtdparts

device nand0 <nand_mtd>, # parts = 2
 #: name			size		offset		mask_flags
 0: uboot               0x000c0000	0x00000000	1
 1: root                0x07f00000	0x00100000	0

active partition: nand0,0 - (uboot) 0x000c0000 @ 0x00000000

defaults:
mtdids  : <NULL>
mtdparts: <NULL>
Marvell>>

Maybe i should just give up the NAND and focus on USB ^^



Edited 1 time(s). Last edit at 11/29/2018 03:15AM by Ironaxe.
Re: UART Boot DNS-320 B1 with broken NAND
November 29, 2018 05:57AM
Ironaxe,

Yes :) perhaps getting USB roofs working is a better idea. I did not see any thing you did wrong. It should work.

However, flashing uboot/mtd insde Debian is always a better approach (I’ve mentioned this many times in this forum).

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: UART Boot DNS-320 B1 with broken NAND
November 29, 2018 06:16AM
Ok.
Then lets go this way.
( More reading ^^ )

Hope you can help me further. ^^



Edited 1 time(s). Last edit at 11/29/2018 11:02AM by Ironaxe.
Re: UART Boot DNS-320 B1 with broken NAND
November 29, 2018 04:25PM
The latest Kirkwood rootfs release thread:

https://forum.doozan.com/read.php?2,12096

Quote

Latest released rootfs: Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 (24 Jul 2017)


You need to look for the DTS for this DNS-320 B1.

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 1 time(s). Last edit at 11/29/2018 06:58PM by bodhi.
Re: UART Boot DNS-320 B1 with broken NAND
November 29, 2018 06:57PM
Ironaxe,

Use this DTB in my kernel release rootfs Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2.

dts/kirkwood-dns320.dtb

So when you do Step 4, that is the correct DTB name:

Quote

Updated 24 Jul 2017:

Basic Debian stretch Kirkwood rootfs for most Kirwood plugs:

- tarball size: 188M
- install size: 488M
- The init system used in this rootfs is sysvinit . To boot with systemd, see note 2 below.
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, isc-dhcp-client, dialog, bzip2, nfs server/client, iperf, ethtool, sysvinit-core, sysvinit, and sysvinit-utils.
- see LED controls in /etc/rc.local, and /etc/init.d/halt
- see some useful aliases in /root/.profile
- root password: root

Download at Dropbox:

Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2

md5:
bf3d29569943875df348fb5ca03b348c
sha256:
4ed5714fdb123cdb40e973f3d0754e91cd199b75a9874018f2b5dc9cfa8ae8bb

And remember to check the hash of what you download, as always.

Installation:

Installation can be done on any Linux box, with a fresh USB drive (SD card or HDD would work fine too).

Note: all steps below must be done while logging in as root user (not sudo). If you are not the root user then don't continue, because the rootfs will not work.

1. Format a new USB drive with a single Ext3 partition, and label it rootfs. If you are running the latest U-Boot for Kirkwood then you can use Ext4.

2. Mount the drive on a Linux box. cd to top level directory and extract it. It is assuming the USB drive is mounted at /media/sdb1
cd /media/sdb1
tar -xjf Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2

3. Adjust fstab (optional).

Edit /media/sdb1/etc/fstab entry for root device to match the rootfstype of your rootfstype if you use Ext4 or Ext2. However, you can keep it as is without problem in booting since the kernel will figure out which file system the rootfs was formatted.

LABEL=rootfs / ext3 noatime,errors=remount-ro 0 1

4. Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Skip this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time).

Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box (see the folder /media/sdb1/boot/dts for the exact spelling of your Kirkwood box name).

Generate the uImage with DTB embedded inside:
cd /media/sdb1/boot
cp -a zImage-4.12.1-kirkwood-tld-1 zImage.fdt
cat dts/kirkwood-dns320.dtb >> zImage.fdt
mv uImage uImage.orig
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.12.1-kirkwood-tld-1 -d zImage.fdt uImage
sync

If your Linux box does not have mkimage, then install it

apt-get install u-boot-tools

5. Done. Take this USB rootfs to your plug and cold start. After booted into Debian, see Note1 and Note2 below. It is very important that you do Note1 steps to secure your box.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: UART Boot DNS-320 B1 with broken NAND
November 30, 2018 02:48AM
So close ^^

root@debian:/u-boot# ./tools/kwboot -t -B 115200 /dev/ttyUSB0 -b mtd0.dns-320 -p
Sending boot message. Please reboot the target.../
Sending boot image...
  0 % [......................................................................]
  0 % [......................................................................]
  1 % [......................................................................]
  2 % [......................................................................]
 .......
 98 % [......................................................................]
 99 % [......................................................................]
 99 % [..]
[Type Ctrl-\ + c to quit]


 ** MARVELL BOARD: DB-88F6702A-BP LE 

U-Boot 1.1.4 (Apr 19 2012 - 11:21:19) Marvell version: 3.6.0.DNS-320B.01

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 166Mhz 

DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB 
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled 
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0 
Marvell>> setenv ethaddr AC:F1:DF:12:DF:9A
Marvell>> setenv ipaddr 192.168.1.103
Marvell>> setenv bootargs console=ttyS0,115200 root=/dev/sda1 usb-storage.delay_use=0 rootdelay=1 rw
Marvell>> usb reset ; ext2load usb 0:1 0xa00000 /boot/uImage ; ext2load usb 0:1 0xf00000 /boot/uInitrd
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
.................................................................................................................................................................................................................................................................................................................................................................................

3835017 bytes read
....
.........................................................................................................................................................................................................................................................................................................................................................................................................................
.....................................................................................................................................................................................................................................................................................................

7245696 bytes read
Marvell>> bootm 0xa00000 0xf00000
## Booting image at 00a00000 ...
   Image Name:   Linux-4.12.1-kirkwood-tld-1
   Created:      2018-11-30   9:27:17 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3834953 Bytes =  3.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00f00000 ...
   Image Name:   initramfs-4.12.1-kirkwood-tld-1
   Created:      2017-07-24   0:18:23 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7245632 Bytes =  6.9 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

And thats it :(

I found a DTS File for the 320L ( Actually the DNS-320 Rev. B is a DNS-320L Rev. A )
I opened the mtd0.dns-320 File with a Hex Editor and it stated DNS-320L and not DNS-320.
DNS-320L DTS File



Edited 1 time(s). Last edit at 11/30/2018 02:48AM by Ironaxe.
Re: UART Boot DNS-320 B1 with broken NAND
November 30, 2018 03:14AM
The load addresses are not right.

Try

setenv ethaddr AC:F1:DF:12:DF:9A
setenv ipaddr 192.168.1.103
setenv bootargs console=ttyS0,115200 root=/dev/sda1 usb-storage.delay_use=0 rootdelay=1 rw earlyprintk=serial
usb reset ; ext2load usb 0:1 0x800000 /boot/uImage ; ext2load usb 0:1 0x2100000 /boot/uInitrd
bootm 0x800000 0x2100000

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: UART Boot DNS-320 B1 with broken NAND
November 30, 2018 03:24AM
Better :)
Just no Ethernet....

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] OF: fdt: Machine model: D-Link DNS-320 NAS (Rev A1)
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 usb-storage.delay_use=0 rootdelay=1 rw earlyprintk=serial
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 109416K/131072K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 21656K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0900000   (9184 kB)
[    0.000000]       .init : 0xc0c00000 - 0xc0d00000   (1024 kB)
[    0.000000]       .data : 0xc0d00000 - 0xc0db3274   ( 717 kB)
[    0.000000]        .bss : 0xc0db9b9c - 0xc0e01e60   ( 289 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[    0.000009] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[    0.007915] Switching to timer-based delay loop, resolution 6ns
[    0.014390] Console: colour dummy device 80x30
[    0.018977] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[    0.029590] pid_max: default: 32768 minimum: 301
[    0.034489] Security Framework initialized
[    0.038829] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.045507] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.053570] CPU: Testing write buffer coherency: ok
[    0.059607] Setting up static identity map for 0x100000 - 0x100058
[    0.066139] mvebu-soc-id: MVEBU SoC ID=0x6702, Rev=0x3
[    0.074980] devtmpfs: initialized
[    0.083976] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.093947] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.100567] prandom: seed boundary self test passed
[    0.110026] prandom: 100 self tests passed
[    0.114191] pinctrl core: initialized pinctrl subsystem
[    0.120756] NET: Registered protocol family 16
[    0.125780] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.134508] cpuidle: using governor ladder
[    0.138802] cpuidle: using governor menu
[    0.143329] Feroceon L2: Enabling L2
[    0.147005] Feroceon L2: Cache support initialised.
[    0.152376] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[    0.169129] No ATAGs?
[    0.179924] vgaarb: loaded
[    0.185393] SCSI subsystem initialized
[    0.189796] usbcore: registered new interface driver usbfs
[    0.195421] usbcore: registered new interface driver hub
[    0.200928] usbcore: registered new device driver usb
[    0.207219] clocksource: Switched to clocksource orion_clocksource
[    0.316436] VFS: Disk quotas dquot_6.6.0
[    0.320582] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.339315] NET: Registered protocol family 2
[    0.344564] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.351645] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.358087] TCP: Hash tables configured (established 1024 bind 1024)
[    0.364580] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.370510] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.377016] NET: Registered protocol family 1
[    0.381918] RPC: Registered named UNIX socket transport module.
[    0.387972] RPC: Registered udp transport module.
[    0.392742] RPC: Registered tcp transport module.
[    0.397546] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.404295] Unpacking initramfs...
[    1.156623] Freeing initrd memory: 7076K
[    1.160903] NetWinder Floating Point Emulator V0.97 (double precision)
[    1.168502] audit: initializing netlink subsys (disabled)
[    1.174425] Initialise system trusted keyrings
[    1.179000] audit: type=2000 audit(1.156:1): state=initialized audit_enabled=0 res=1
[    1.186857] Key type blacklist registered
[    1.191135] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    1.197765] zbud: loaded
[    1.201451] NFS: Registering the id_resolver key type
[    1.206591] Key type id_resolver registered
[    1.210918] Key type id_legacy registered
[    1.215014] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.221806] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.228439] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.235743] fuse init (API version 7.26)
[    1.240120] orangefs_debugfs_init: called with debug mask: :none: :0:
[    1.246848] orangefs_init: module version upstream loaded
[    1.252342] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[    2.567226] random: fast init done
[    8.273679] Key type asymmetric registered
[    8.278134] Asymmetric key parser 'x509' registered
[    8.283135] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    8.290727] io scheduler noop registered
[    8.294714] io scheduler deadline registered
[    8.299189] io scheduler cfq registered (default)
[    8.305451] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    8.314962] mv_xor f1060800.xor: Marvell shared XOR driver
[    8.378088] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr )
[    8.385952] mv_xor f1060900.xor: Marvell shared XOR driver
[    8.448096] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr )
[    8.456213] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    8.464102] console [ttyS0] disabled
[    8.467875] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A
[    8.476919] console [ttyS0] enabled
[    8.476919] console [ttyS0] enabled
[    8.484002] bootconsole [earlycon0] disabled
[    8.484002] bootconsole [earlycon0] disabled
[    8.493365] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 26, base_baud = 10416666) is a 16550A
[    8.511815] loop: module loaded
[    8.515627] sata_mv f1080000.sata: slots 32 ports 2
[    8.523612] scsi host0: sata_mv
[    8.527271] scsi host1: sata_mv
[    8.530676] ata1: SATA max UDMA/133 irq 33
[    8.534754] ata2: SATA max UDMA/133 irq 33
[    8.540103] nand: Could not find valid ONFI parameter page; aborting
[    8.546441] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[    8.552844] nand: Hynix NAND 128MiB 3,3V 8-bit
[    8.557293] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    8.564834] Scanning device for bad blocks
[    8.673065] 6 ofpart partitions found on MTD device orion_nand
[    8.678898] Creating 6 MTD partitions on "orion_nand":
[    8.684021] 0x000000000000-0x000000100000 : "u-boot"
[    8.690454] 0x000000100000-0x000000600000 : "uImage"
[    8.696881] 0x000000600000-0x000000b00000 : "ramdisk"
[    8.703475] 0x000000b00000-0x000007100000 : "image"
[    8.710565] 0x000007100000-0x000007b00000 : "mini firmware"
[    8.717458] 0x000007b00000-0x000008000000 : "config"
[    8.724976] libphy: Fixed MDIO Bus: probed
[    8.730021] libphy: orion_mdio_bus: probed
[    8.734510] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    8.741982] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    8.748591] ehci-pci: EHCI PCI platform driver
[    8.753084] ehci-orion: EHCI orion driver
[    8.757366] orion-ehci f1050000.ehci: EHCI Host Controller
[    8.762894] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    8.770822] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000
[    8.797248] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    8.803524] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    8.810336] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    8.817566] usb usb1: Product: EHCI Host Controller
[    8.822424] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd
[    8.829133] usb usb1: SerialNumber: f1050000.ehci
[    8.834627] hub 1-0:1.0: USB hub found
[    8.838464] hub 1-0:1.0: 1 port detected
[    8.843121] usbcore: registered new interface driver usb-storage
[    8.849566] mousedev: PS/2 mouse device common for all mice
[    8.870355] ata1: SATA link down (SStatus 0 SControl F300)
[    9.197248] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    9.209025] ata2: SATA link down (SStatus 0 SControl F300)
[    9.389833] usb 1-1: New USB device found, idVendor=058f, idProduct=6387
[    9.396523] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    9.403666] usb 1-1: Product: Mass Storage Device
[    9.408374] usb 1-1: Manufacturer: JetFlash
[    9.412543] usb 1-1: SerialNumber: F1V4T9I4
[    9.417691] usb-storage 1-1:1.0: USB Mass Storage device detected
[    9.424117] scsi host2: usb-storage 1-1:1.0
[    9.430307] scsi 2:0:0:0: Direct-Access     JetFlash Transcend 1GB    8.07 PQ: 0 ANSI: 2
[    9.440872] sd 2:0:0:0: [sda] 1972224 512-byte logical blocks: (1.01 GB/963 MiB)
[    9.448738] sd 2:0:0:0: [sda] Write Protect is off
[    9.453985] sd 2:0:0:0: [sda] No Caching mode page found
[    9.459349] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    9.489479]  sda: sda1
[    9.494240] sd 2:0:0:0: [sda] Attached SCSI removable disk
[    9.937250] rtc-mv f1010300.rtc: internal RTC not ticking
[    9.942828] i2c /dev entries driver
[    9.948393] hidraw: raw HID events driver (C) Jiri Kosina
[    9.954159] drop_monitor: Initializing network drop monitor service
[    9.960699] NET: Registered protocol family 17
[    9.965223] Key type dns_resolver registered
[    9.970382] registered taskstats version 1
[    9.974460] Loading compiled-in X.509 certificates
[    9.979324] zswap: loaded using pool lzo/zbud
[    9.994596] Key type big_key registered
[   10.008742] Key type encrypted registered
[   10.014398] hctosys: unable to open rtc device (rtc0)
[   10.022901] Freeing unused kernel memory: 1024K
Loading, please wait...
starting version 232
[   10.520638] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Warning: fsck not present, so skipping root file system
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ ok ] Setting hostname to 'debian'...done.
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
. ok 
[ ok ] Synthesizing the initial hotplug events...[   14.173285] input: gpio_keys as /devices/platform/gpio_keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[   14.479281] orion_wdt: Initial timeout 25 sec
[   14.589399] marvell-cesa f1030000.crypto: CESA device successfully registered
[   14.628629] sd 2:0:0:0: Attached scsi generic sg0 type 0
done.
[ ok ] Activating swap:.
[....] Will now check root file system:fsck from util-linux 2.29.2
[/sbin/fsck.ext2 (1) -- /] fsck.ext2 -y -C0 /dev/sda1 
e2fsck 1.43.4 (31-Jan-2017)
rootfs: clean, 14456/61568 files, 174420/246272 blocks
. ok 
[   17.322662] random: crng init done
[ ok ] Will now activate lvm and md swap:done.
[info] Will now check all file systems.
fsck from util-linux 2.29.2
Checking all file systems.
LABEL=rootfs is mounted
[....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is wri[ ok ..
[ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done.
[ ok .
[ ok ] Will now mount local filesystems:.
[ ok ] Will now activate swapfile swap:done.
[ ok ] Checking minimum space in /tmp...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables...done.
[ ok ] Initializing random number generator...done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5
Copyright 2004-2016 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Cannot find device "eth0"
Failed to get interface index: No such device

If you think you have received this message due to a bug rather
than a configuration issue please read the section on submitting
bugs on either our web page at www.isc.org or in the README file
before submitting a bug.  These pages explain the proper
process and the information we find helpful for debugging..

exiting.
ifup: failed to bring up eth0
failed.
[   20.587552] NET: Registered protocol family 10
[   20.595040] Segment Routing with IPv6
[ ok ] Starting RPC port mapper daemon: rpcbind.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1267 (syslogd)
. ok 
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1266 (klogd)
. ok 
[ ok ] Running local boot scripts (/etc/rc.local).

Debian GNU/Linux 9 debian ttyS0

debian login:



Edited 2 time(s). Last edit at 11/30/2018 04:27AM by Ironaxe.
Re: UART Boot DNS-320 B1 with broken NAND
November 30, 2018 05:19PM
Let me see. Perhaps I can take a look at the your link DTS and compile it. Probably a different PHY address is used.

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 1 time(s). Last edit at 11/30/2018 05:20PM by bodhi.
Re: UART Boot DNS-320 B1 with broken NAND
November 30, 2018 05:57PM
Ah. The mainline DNS-320 has no Ethernet activation node!

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: UART Boot DNS-320 B1 with broken NAND
December 01, 2018 02:07AM
Lol.
OK.
I tried to compile the Kernel with the DTS File, but when it boots the uImage i get a "wrong Hardware ID" Error.
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: