Hi
I have
bricked my Pogoplug pink V2 E02 .
During jeffs install got errors in uboot and corrupt debs error , checked the thread
http://forum.doozan.com/read.php?2,4323,page=1 then installed
using gorgone wget to install correctly , booted fine . Uboot had errors but it booted fine with the debian prompt . Tried installing new kernel 3.2 .
Errors in last command
mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-3.3.2-kirkwood-dg -d initrd.img-3.3.2-kirkwood-dg uInitrd
that file not found , tried again but still same error .Knew was screwed so thought to update unboot atleast so i have a booting system .Installed the new uboot from the new kernel 3.2 thread , automated install and not manual version .It did not finish lots of errors , tried twice thrice but no luck .
Rebooted and as expected bricked , no lights , cannot find ip with ipscan , no ip is there
Got nokia ca42 and made the serial cable . Rebooted , luckily uBoot seems to be working, but uBoot environment is messed up .
printenv is
u-boot>> printenv
arcNumber=2097
baudrate=115200
bootcmd=run bootcmd_usb; usb stop; run bootcmd_pogo; reset
bootcmd_pogo=fsload uboot-original-mtd0.kwb; go 0x800200
bootcmd_usb=run usb_init; run usb_load_uimage; run set_bootargs_usb; run usb_boot;
bootdelay=3
console=ttyS0,115200
ethact=egiga0
ethaddr=02:50:43:b8:df:7d
led_error=orange blinking
led_exit=green off
led_init=green blinking
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts
stderr=serial
stdin=serial
stdout=serial
usb_boot=if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000;else bootm 0x800000;fi;
usb_device=0:1
usb_init=usb start
usb_load_uimage=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage
usb_root=/dev/sda1
usb_rootdelay=10
usb_rootfstype=ext2
Got the rootfs from here
http://forum.doozan.com/read.php?2,7806 and booted correctly to debian prompt . Thanks to davygravy , I came to
root@debian-kirkwood-wide login : prompt .
Installed rescue system
http://forum.doozan.com/read.php?4,7915 from here . Arch number set was 3542 &untarred and installed the rescue system . Installed other apps like transmission , samba on working debian rootfs install
Till now not rebooted and after rebooted screwed and this is the error
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
Retry count exceeded; starting again
this is version
u-boot>> version
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
printnv
u-boot>> printenv
baudrate=115200
bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm
bootcmd_pogo=run bootcmd_rescue
bootcmd_rescue=run set_bootargs_rescue; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000
bootdelay=5
ethact=egiga0
ethaddr=02:50:43:e4:d9:b1
rescue_installed=1
set_bootargs_rescue=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts
stderr=serial
stdin=serial
stdout=serial
Environment size: 540/131068 bytes
Booted rescue and came to rescue:~#
here i tried to update uboot manually which again gave errors and did not finish manually ,rebooted came to the uboot prompt and it started becoming unresponsive that is not taking keyboard , tried 4/5 times didint work . Then added the serial cable jumpers again to check
it worked for 2 minutes , i cancelled auto boot came to uboot prompt , gave command version and after that it stopped taking keyboard
restarted and serial console is empty now , doesnt show the start up log . Well now its completely lost , no output from serial also , just blank putty screen
another thing when i give power to pogo the green LED has stopped glowing .When i switch it on and off then LAN and power LED glows and again off
All these steps were completely tutored to me by our member varkey . A big thanks to him and this would not have been possible without him .
Now the jtag journey starts .
Now please tell me out of these which will revive my Pogoplug . They are available locally here and ebay will take minimum 20 days so want to buy from here .
http://store.hbeonlabs.com/index.php?route=product/product&filter_name=jtag&product_id=125
http://store.hbeonlabs.com/index.php?route=product/product&filter_name=jtag&product_id=157
http://store.hbeonlabs.com/index.php?route=product/product&filter_name=jtag&product_id=124
http://store.hbeonlabs.com/index.php?route=product/product&filter_name=jtag&product_id=139
or this one
http://store.hbeonlabs.com/index.php?route=product/product&product_id=58
and
i do know of this wiggler clone which works
http://www.ebay.com/itm/270889738328?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
No issues of using it on parallel or usb port
thanks
Edited 4 time(s). Last edit at 07/09/2012 04:01AM by kuduku.