Bricked Pogo E02 not loading from USB

PogoE02> reset
resetting ...


U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0 
PogoE02> printenv
arcNumber=3542
baudrate=115200
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
bootdelay=3
console=ttyS0,115200
dtb_file=/boot/dts/kirkwood-pogo_e02.dtb
ethact=egiga0
ethaddr=52:3b:20:9c:11:51
fileaddr=800000
filesize=20000
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
ipaddr=192.168.1.123
led_error=orange blinking
led_exit=green off
led_init=green blinking
machid=dd6
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
serverip=192.168.1.156
stderr=serial
stdin=serial
stdout=serial
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_device=0:1
usb_init=run usb_scan
usb_ready_retry=30
usb_root=/dev/sda1
usb_rootdelay=10
usb_rootfstype=ext3
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_scan_list=1 2 3 4
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params

Environment size: 2502/131068 bytes
PogoE02> usb reset
resetting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 5
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 4
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 3
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 2
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 1
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80a88
unable to get device descriptor (error=-1) retry: 0
1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
PogoE02> 

radsfaninlv,

That has confirmed what David and I suspected the problem was.

u-boot-2017.07-tld-1 supposed to show

PogoE02> usb reset
usb reset
resetting USB...
USB0:   USB EHCI 1.00
........
Use USB retry period from the environment: 30 second(s)
1 Storage Device(s) found

If the usb_ready_retry env is

usb_ready_retry=30

So check your power supply cable and perhaps at the power coming to power supply and out of power supply to the board (i.e how much voltage and AMP, is it enough power?).

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

I tried changing the power cord and moving to a different room with the same result.

I removed the power supply board and plugged it in and took some measurements where it is printed GND and 5V (the back of the plug receptical that connects the power supply board to the main board). i got the following results:

Volts AC: 7.1
Volts DC: 0.1
mAmps: No reading

Is there another place where I should take the readings?