Problems Netgear Stora M2110 kwboot

Hallo,

i tried to set up Debian on my Netgear Stora, but i think i have made a mistake and i hope anyone could help me.

so it looks when it boots:

        __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__| 
 ** MARVELL BOARD: RD-88F6281A LE 

U-Boot 1.1.4 (Sep  4 2009 - 09:36:11) Marvell version: 3.4.14

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CEE60

Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz 

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size  64MB 
DRAM CS[1] base 0x04000000   size  64MB 
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
CRC in Flash: ffffffff, Calculated CRC: 619d86db
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
## Error: environment overflow, "stdin" deleted
## Error: environment overflow, "stdout" deleted
## Error: environment overflow, "stderr" deleted

CPU : Marvell Feroceon (Rev 1)
## Error: environment overflow, "console" deleted
## Error: environment overflow, "mainlineLinux" deleted
## Error: environment overflow, "CASset" deleted
## Error: environment overflow, "enaMonExt" deleted
## Error: environment overflow, "enaCpuStream" deleted
## Error: environment overflow, "enaWrAllo" deleted
## Error: environment overflow, "pexMode" deleted
## Error: environment overflow, "disL2Cache" deleted
## Error: environment overflow, "setL2CacheWT" deleted
## Error: environment overflow, "disL2Prefetch" deleted
## Error: environment overflow, "enaICPref" deleted
## Error: environment overflow, "enaDCPref" deleted
## Error: environment overflow, "sata_dma_mode" deleted
## Error: environment overflow, "MALLOC_len" deleted
## Error: environment overflow, "ethprime" deleted
## Error: environment overflow, "netbsd_en" deleted
## Error: environment overflow, "vxworks_en" deleted
## Error: environment overflow, "bootargs_root" deleted
## Error: environment overflow, "bootargs_end" deleted
## Error: environment overflow, "image_name" deleted
## Error: environment overflow, "bootcmd" deleted
## Error: environment overflow, "standalone" deleted
## Error: environment overflow, "bootdelay" deleted
## Error: environment overflow, "disaMvPnp" deleted
## Error: environment overflow, "disaMvPnp" deleted
## Error: environment overflow, "ethaddr" deleted
## Error: environment overflow, "ethmtu" deleted
## Error: environment overflow, "eth1addr" deleted
## Error: environment overflow, "eth1mtu" deleted
## Error: environment overflow, "mvPhoneConfig" deleted
## Error: environment overflow, "mvNetConfig" deleted
## Error: environment overflow, "usb0Mode" deleted
## Error: environment overflow, "yuk_ethaddr" deleted
## Error: environment overflow, "nandEcc" deleted
## Error: environment overflow, "hddPowerCtrl" deleted
## Error: environment overflow, "netretry" deleted
## Error: environment overflow, "rcvrip" deleted
## Error: environment overflow, "loadaddr" deleted
## Error: environment overflow, "autoload" deleted
## Error: environment overflow, "enaAutoRecovery" deleted

Streaming disabled 
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: device mode
PEX 0: interface detected no Link.
Net:   ## Error: environment overflow, "ethact" deleted
egiga0, egiga1## Error: environment overflow, "ethact" deleted

USB:   scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
Aquiring an IP address using DHCP...
## Error: environment overflow, "ethact" deleted
*** ERROR: `ethaddr' not set
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
## Error: environment overflow, "ethact" deleted
*** ERROR: `ethaddr' not set
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
## Error: environment overflow, "ethact" deleted
*** ERROR: `ethaddr' not set
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
Failed to retreive an IP address assuming default (<NULL>)!
Starting the Recovery process to retreive the file...
## Error: environment overflow, "ethact" deleted
*** ERROR: `ethaddr' not set
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
Failed
Power Button is pressed!
MPP Sel: 00000530, Data IN Enable: 00020058, Data In Polarity: 00000040, Data In: 00000011
Power Button is released!
MAC: 00:01:01:E9:34:80, IP: 10.233.52.128
## Error: environment overflow, "ethaddr" deleted
## Error: environment overflow, "ipaddr" deleted
## Error: environment overflow, "serverip" deleted
## Error: environment overflow, "netmask" deleted
## Error: environment overflow, "image_name" deleted
## Error: environment overflow, "console" deleted
## Error: environment overflow, "bootargs_root" deleted
## Error: environment overflow, "rootpath" deleted
## Error: environment overflow, "ethact" deleted
*** ERROR: `serverip' not set
## Error: environment overflow, "bootargs" deleted
## Booting image at 00800000 ...
Bad Magic Number
Marvell>>

i downloaded the latest U-boot uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb and managed to boot the MS2000 with the help of kwboot.

it works until i should reboot.

root@lenovo-debian:/home/joker/Downloads/kwboot-tool# ./kwboot -t /dev/ttyUSB0 -b uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb -p
Sending boot message. Please reboot the target...

How could i reboot the Stora?
The Power Button does not work. when i turn off and on Power ist does not boot and no LED is working.

I hope you could help me, thanks.



Edited 2 time(s). Last edit at 01/16/2021 01:02PM by Martin83.

Martin83,

> i downloaded the latest U-boot
> uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb and
> managed to boot the MS2000 with the help of
> kwboot.
>
> it works until i should reboot.
>
>

> root@lenovo-debian:/home/joker/Downloads/kwboot-tool#
> ./kwboot -t /dev/ttyUSB0 -b
> uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb -p
> Sending boot message. Please reboot the target...
>

Did you create the USB rootfs using Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2 from the release thread?

https://forum.doozan.com/read.php?2,12096

> How could i reboot the Stora?

At this point, I would say forget about stock OS for this Stora. Once you booted into Debian on USB, you can flash u-boot uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb permanently and run Debian on USB.

And then set it up to run on HDD if you like to do so.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

hi,

thanks for your answer!

Quote

Did you create the USB rootfs using Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2 from the release thread?

Yes, i have done it like it is explained on 25 Aug. 2019 including step 4.

But at this point, i do not know how to boot it on my Stora.

Martin



Edited 1 time(s). Last edit at 01/16/2021 07:02PM by Martin83.

Martin83,

Quote

root@lenovo-debian:/home/joker/Downloads/kwboot-tool# ./kwboot -t /dev/ttyUSB0 -b uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb -p
Sending boot message. Please reboot the target...

So did you see anything more after this? did uboot.2017.07-tld-1.netgear_ms2110 start? please pos the serial console log of this kwboot attempt.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Hi,

in terminal nothing more happend.

In the console it looks like this:

## Error: environment overflow, "ethaddr" deleted
## Error: environment overflow, "ipaddr" deleted
## Error: environment overflow, "serverip" deleted
## Error: environment overflow, "netmask" deleted
## Error: environment overflow, "image_name" deleted
## Error: environment overflow, "console" deleted
## Error: environment overflow, "bootargs_root" deleted
## Error: environment overflow, "rootpath" deleted
## Error: environment overflow, "ethact" deleted
*** ERROR: `serverip' not set
## Error: environment overflow, "bootargs" deleted
## Booting image at 00800000 ...
Bad Magic Number
Marvell>> �"3DUfw�"3DUfw�"3DUfw�"3DUfw"3DUfw"3DUfw"3DUfw�"3DUfw�"3DUfw�"3DUfw"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw�"3DUfw"3DUfw�"3DUfw"3DUfw�"3DUfw�"3DUfw

Martin83,

When you start kwboot and see:

root@lenovo-debian:/home/joker/Downloads/kwboot-tool# ./kwboot -t /dev/ttyUSB0 -b uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb -p
Sending boot message. Please reboot the target...

And then nothing happened, try Control-C and recall the command and execute again. Try this serval times.

There are Stora boxes that don't work with UART booting. So it is possible that this box is the version that does not.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

That's when you power up or reset the device for booting.

I only experienced problems with kwboot when I forgot the -p parameter. Works like a charm.

Looks like you already overwritten the environment variables with the 2017 variables. So get your ext3 stick ready and boot after the injection.

bodhi Wrote:
-------------------------------------------------------
> Martin83,
>
> When you start kwboot and see:
>
>

> root@lenovo-debian:/home/joker/Downloads/kwboot-tool#
> ./kwboot -t /dev/ttyUSB0 -b
> uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb -p
> Sending boot message. Please reboot the target...
>

>
> And then nothing happened, try Control-C and
> recall the command and execute again. Try this
> serval times.
>
> There are Stora boxes that don't work with UART
> booting. So it is possible that this box is the
> version that does not.

Hi there,
So what can be done additionally if I get permamnent
Sending boot message. Please reboot the target...
Should I send Stora to garbage or somehow can use it?
There are no reaction from the box, only fan spinning....

> So what can be done additionally if I get
> permamnent
> Sending boot message. Please reboot the
> target...
> Should I send Stora to garbage or somehow can use
> it?

Most Kirkwood boxes have JTAG. But I'm not sure if the Stora has JTAG exposed. Usually you'll need to solder the header. See these examples in the Wiki thread

https://forum.doozan.com/read.php?2,23630

Quote

Unbricking with Serial Console & JTAG console

Repair Pogo E02 with Raspberry PI (JTAG) and OpenOCD
Unbricking Dockstar with JTAG and OpenOCD

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Hi here,

For Stora jTAG :

https://sigri44.github.io/OpenStora/wiki/index_Jtag_Pinout

Thanks Sigri!

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)